NETGEAR-ROUTING-MIB
AI MIB Summary
The NETGEAR-ROUTING-MIB provides vendor-specific SNMP access to monitor and configure dynamic routing protocols, static route tables, and interface routing states on NETGEAR enterprise routers and switches. This module enables the collection of routing table entries, protocol adjacency states, and route metric counters for network topology analysis and troubleshooting.
The NETGEAR Private MIB for Routing
Main OID:
agentRouting.ng7000Switch.2
114
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
114 total| Object Name |
|---|
agentRoutingThe NETGEAR Private MIB for Routing MODULE-IDENTITY .ng7000Switch.2 |
agentSwitchArpGroup OBJECT IDENTIFIER .ng7000Switch.2.1 |
agentSwitchArpAgeoutTimeConfigures the ARP entry ageout time in seconds.
Allowable range: 15-21600rw Integer32 .ng7000Switch.2.1.1 |
agentSwitchArpResponseTimeConfigures the ARP request response timeout in seconds.
Allowable range: 1-10rw Integer32 .ng7000Switch.2.1.2 |
agentSwitchArpMaxRetriesConfigures the ARP count of maximum request for retries.
Allowable range: 0-10rw Integer32 .ng7000Switch.2.1.3 |
agentSwitchArpCacheSizeConfigures the ARP maximum number of entries in the cache.
Allowable range is platform-specific.rw Integer32 .ng7000Switch.2.1.4 |
agentSwitchArpDynamicRenewThis indicates the current setting of ARP dynamic renew mode.rw Enumeration .ng7000Switch.2.1.5 |
agentSwitchArpTotalEntryCountCurrentCurrent number of entries in the ARP cache.ro Gauge32 .ng7000Switch.2.1.6 |
agentSwitchArpTotalEntryCountPeakPeak number of entries recorded in the ARP cache over
time. This value is restarted whenever the ARP cache
size is changed.ro Gauge32 .ng7000Switch.2.1.7 |
agentSwitchArpStaticEntryCountCurrentCurrent number of configured static ARP entries.ro Gauge32 .ng7000Switch.2.1.8 |
agentSwitchArpStaticEntryCountMaxMaximum number of configurable static ARP entries.ro Integer32 .ng7000Switch.2.1.9 |
agentSwitchArpTableThis table augments the MIB-II ipNetToMediaTable by providing
per-interface ARP entry information. SEQUENCE OF AgentSwitchArpEntry .ng7000Switch.2.1.10 |
agentSwitchArpEntry AgentSwitchArpEntry .ng7000Switch.2.1.10.1 |
agentSwitchArpAgeThis defines the time (in seconds) since the ARP entry
was last refreshed. This value is 0 for ARP entries of
type local(1) or static(3), since these entries are
not subject to aging.ro TimeTicks (SNMPv2-SMI) .ng7000Switch.2.1.10.1.1 |
agentSwitchArpIpAddressThe IP Address assigned to each interface.ro IpAddress .ng7000Switch.2.1.10.1.2 |
agentSwitchArpMacAddressThe hardware MAX Address that each interface maps to.rw PhysAddress (SNMPv2-TC) .ng7000Switch.2.1.10.1.3 |
agentSwitchArpInterfaceThe Associated IfIndex which identified the ARP Entry.ro Integer32 .ng7000Switch.2.1.10.1.4 |
agentSwitchArpTypeThe type of ARP entry.ro Enumeration .ng7000Switch.2.1.10.1.5 |
agentSwitchArpStatusThe status of this ARP entry. Setting this object destroy will remove the entry.rw RowStatus (SNMPv2-TC) .ng7000Switch.2.1.10.1.6 |
agentSwitchIpGroup OBJECT IDENTIFIER .ng7000Switch.2.2 |
agentSwitchIpRoutingModeAdministratively enables/disables routing on the switch.rw Enumeration .ng7000Switch.2.2.1 |
agentSwitchIpInterfaceTable SEQUENCE OF AgentSwitchIpInterfaceEntry .ng7000Switch.2.2.3 |
agentSwitchIpInterfaceEntry AgentSwitchIpInterfaceEntry .ng7000Switch.2.2.3.1 |
agentSwitchIpInterfaceIfIndexThe IfIndex associated with this instance.ro Integer32 .ng7000Switch.2.2.3.1.1 |
agentSwitchIpInterfaceIpAddressThe IpAddress assigned to this interface. When setting this value,
the value of agentSwitchIpInterfaceNetMask must be set at the same time.rw IpAddress .ng7000Switch.2.2.3.1.2 |
agentSwitchIpInterfaceNetMaskThe NetMask assigned to this interface. When setting this value, the
value of agentSwitchIpInterfaceIpAddress must be set at the same time.rw IpAddress .ng7000Switch.2.2.3.1.3 |
agentSwitchIpInterfaceClearIpSets the interfaces IpAddress and NetMask back to 0.0.0.0rw Enumeration .ng7000Switch.2.2.3.1.4 |
agentSwitchIpInterfaceRoutingModeEnables or disables routing for this interface.rw Enumeration .ng7000Switch.2.2.3.1.5 |
agentSwitchIpInterfaceProxyARPModeEnables or disables Proxy ARP for this interface.rw Enumeration .ng7000Switch.2.2.3.1.6 |
agentSwitchIpInterfaceMtuValueConfigures the MTU value for this interface. If the value returned is 0
this interface is not enabled for routing. It is not valid to set this
value to 0 if routing is enabled.rw Unsigned32 (0|128..1500) .ng7000Switch.2.2.3.1.7 |
agentSwitchIpRouterDiscoveryTableThere is no global administrative flag for router discovery. The global
routing flag (agentSwitchIpRoutingMode) will be used for this purpose. If routing
is disabled, router discovery is disabled as well. SEQUENCE OF AgentSwitchIpRouterDiscoveryEntry .ng7000Switch.2.2.4 |
agentSwitchIpRouterDiscoveryEntry AgentSwitchIpRouterDiscoveryEntry .ng7000Switch.2.2.4.1 |
agentSwitchIpRouterDiscoveryIfIndexInterface Number to configure Router Discovery on.ro Integer32 .ng7000Switch.2.2.4.1.1 |
agentSwitchIpRouterDiscoveryAdvertiseModeEnable or disable router discovery on the interface.rw Enumeration .ng7000Switch.2.2.4.1.2 |
agentSwitchIpRouterDiscoveryMaxAdvertisementIntervalMaximum time allowed between sending router advertisements
from the interface.rw Integer32 .ng7000Switch.2.2.4.1.3 |
agentSwitchIpRouterDiscoveryMinAdvertisementIntervalMinimum time allowed between sending router advertisements from the interface.
This value must be less than or equal to
agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.rw Integer32 .ng7000Switch.2.2.4.1.4 |
agentSwitchIpRouterDiscoveryAdvertisementLifetimeValue of lifetime field of router advertsisement sent from
the interface.
This value must be greater than or equal to
agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.rw Integer32 .ng7000Switch.2.2.4.1.5 |
agentSwitchIpRouterDiscoveryPreferenceLevelPreferability of the address as a default router address,
related to other addresses on the same subnet. This is defined
as the larger the number, the higher the preference.rw Integer32 .ng7000Switch.2.2.4.1.6 |
agentSwitchIpRouterDiscoveryAdvertisementAddressAddress used when sending router advertisements from the interface.rw IpAddress .ng7000Switch.2.2.4.1.7 |
agentSwitchIpVlanTable SEQUENCE OF AgentSwitchIpVlanEntry .ng7000Switch.2.2.5 |
agentSwitchIpVlanEntryA Static VLAN for which routing can be enabled/disabled AgentSwitchIpVlanEntry .ng7000Switch.2.2.5.1 |
agentSwitchIpVlanIdThe Vlan's Id.ro Integer32 .ng7000Switch.2.2.5.1.1 |
agentSwitchIpVlanIfIndexThe IfIndex associated with this VLAN.ro Integer32 .ng7000Switch.2.2.5.1.2 |
agentSwitchIpVlanRoutingStatusStatus of Routing mode per Vlan.
active(1) - Vlan is enabled for routing
createAndGo(4) - Adds Vlan entry for routing
destroy(6) - Removes Vlan from routingrw RowStatus (SNMPv2-TC) .ng7000Switch.2.2.5.1.3 |
agentSwitchSecondaryAddressTableContains a list of secondary IP Addresses associated with an interface. SEQUENCE OF AgentSwitchSecondaryAddressEntry .ng7000Switch.2.2.6 |
agentSwitchSecondaryAddressEntryA secondary IP Address for a given interface. This IP Address must not
conflict with the IP Address configured in the agentSwitchIpInterfaceTable. AgentSwitchSecondaryAddressEntry .ng7000Switch.2.2.6.1 |
agentSwitchSecondaryIpAddressThe Secondary IP Address assigned to this interface. IpAddress .ng7000Switch.2.2.6.1.1 |
agentSwitchSecondaryNetMaskThe Secondary Net Mask assigned to this interface. This value must be
set during creation, and can not be changed.rw IpAddress .ng7000Switch.2.2.6.1.2 |
agentSwitchSecondaryStatusCreates a new entry in the Secondary Address table.
Allowed values are:
createAndGo(4) - Creates an entry in this table, associating the address
with a given interface. The agentSwitchSecondaryNetMask
object must be set during creation.
destroy(6) - Removes the associated address from the interface.rw RowStatus (SNMPv2-TC) .ng7000Switch.2.2.6.1.3 |
agentRouterRipConfigGroup OBJECT IDENTIFIER .ng7000Switch.2.3 |
agentRouterRipAdminStateSets the administrative mode of RIP in the router.rw Enumeration .ng7000Switch.2.3.1 |
agentRouterRipSplitHorizonModeSets the RIP split horizon operating mode in the router.
A value of none(1) means split horizon processing is
disabled. When set to simple(2), the simple split
horizon technique is used. When set to poisonReverse(3),
the split horizon with poison reverse technique is used.
The default split horizon mode is simple(2).rw Enumeration .ng7000Switch.2.3.2 |
agentRouterRipAutoSummaryModeSets the RIP auto summarization mode in the router.
A value of enable(1) means that routes advertized by
this RIP router are combined, or summarized, whenever
possible into aggregates. When set to disable(2),
routes are not aggregated in RIP updates generated
by this router. The default auto summary mode is
enable(1).rw Enumeration .ng7000Switch.2.3.3 |
agentRouterRipHostRoutesAcceptModeSets the RIP host route acceptance mode in the router.
A value of enable(1) means that host routes advertized
to this RIP router will be accepted (learned) into its
routing table. When set to disable(2), host routes
advertized in RIP updates from neighboring routers
are ignored. The default host routes accept mode is
enable(1).rw Enumeration .ng7000Switch.2.3.4 |
agentRouterRipDefaultMetricDefault metric of redistributed routes, when RIP redistributes
from other protocols.rw Integer32 .ng7000Switch.2.3.5 |
agentRouterRipDefaultMetricConfiguredFlag to determine whether RIP default-metric is configured or not.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.3.6 |
agentRouterRipDefaultInfoOriginateFlag to determine, whether RIP can advertise a default-route learned
from another protocol.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.3.7 |
agentRipRouteRedistTableThis table contains the MIB objects required to configure
route-redistribution for RIP. Here, RIP is the Destination
protocol and the source protocols can be any of : BGP, OSPF,
Static, Connected. SEQUENCE OF AgentRipRouteRedistEntry .ng7000Switch.2.3.8 |
agentRipRouteRedistEntry AgentRipRouteRedistEntry .ng7000Switch.2.3.8.1 |
agentRipRouteRedistSourceSource route, from which RIP can redistribute routes.
This object also acts as the identifier for the
RIP redistribution Table entry.ro Enumeration .ng7000Switch.2.3.8.1.1 |
agentRipRouteRedistModeUser enabels/disables route-redistribution for a particular source
protocol.rw Enumeration .ng7000Switch.2.3.8.1.2 |
agentRipRouteRedistMetricMetric used for redistributing a particular source protocol route
into RIP.rw Integer32 .ng7000Switch.2.3.8.1.3 |
agentRipRouteRedistMetricConfiguredFlag to determine whether RIP redistribute-metric is configured or not.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.3.8.1.4 |
agentRipRouteRedistMatchInternalIf this flag is true, RIP redistributes OSPF internal routes.
It will be non-applicable, when source protocol is other than ospf.rw Enumeration .ng7000Switch.2.3.8.1.5 |
agentRipRouteRedistMatchExternal1If this flag is true, RIP redistributes OSPF External1 routes.
It will be non-applicable, when source protocol is other than ospf.rw Enumeration .ng7000Switch.2.3.8.1.6 |
agentRipRouteRedistMatchExternal2If this flag is true, RIP redistributes OSPF External2 routes.
It will be non-applicable, when source protocol is other than ospf.rw Enumeration .ng7000Switch.2.3.8.1.7 |
agentRipRouteRedistMatchNSSAExternal1If this flag is true, RIP redistributes OSPF NSSA-External1 routes.
It will be non-applicable, when source protocol is other than ospf.rw Enumeration .ng7000Switch.2.3.8.1.8 |
agentRipRouteRedistMatchNSSAExternal2If this flag is true, RIP redistributes OSPF NSSA-External2 routes.
It will be non-applicable, when source protocol is other than ospf.rw Enumeration .ng7000Switch.2.3.8.1.9 |
agentRipRouteRedistDistListAccess-list number of the access-list, which filters routes received
from a source-protocol.rw Unsigned32 .ng7000Switch.2.3.8.1.10 |
agentRipRouteRedistDistListConfiguredFlag to determine whether Access-list is configured or not.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.3.8.1.11 |
agentRip2IfConfTableA list of subnets which require separate
configuration in RIP. Augments rip2IfConfTable
in the RIPv2-MIB. SEQUENCE OF AgentRip2IfConfEntry .ng7000Switch.2.3.9 |
agentRip2IfConfEntryA Single Routing Domain in a single Subnet.
Augments rip2IfConfEntry in RIPv2-MIB. AgentRip2IfConfEntry .ng7000Switch.2.3.9.1 |
agentRip2IfConfAuthKeyIdThe identifier for the authentication key used
on this interface. This field is only meaningful
when the RIPv2-MIB rip2IfConfAuthType is md5(3);
otherwise, the value is not used.rw INTEGER .ng7000Switch.2.3.9.1.1 |
agentRouterOspfConfigGroup OBJECT IDENTIFIER .ng7000Switch.2.4 |
agentOspfDefaultMetricDefault metric of redistributed routes, when OSPF redistributes
from other protocols.rw Integer32 .ng7000Switch.2.4.1 |
agentOspfDefaultMetricConfiguredFlag to determine whether OSPF default-metric is configured or not.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.4.2 |
agentOspfDefaultInfoOriginateFlag to determine, whether OSPF can advertise a default-route learned
from another protocol.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.4.3 |
agentOspfDefaultInfoOriginateAlwaysWhen this flag is true, the router advertises 0.0.0.0/0.0.0.0 always.
Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the
router's forwarding table contains a default route.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.4.4 |
agentOspfDefaultInfoOriginateMetricMetric of the default route,which OSPF advertises when learned from
other protocol.rw Integer32 .ng7000Switch.2.4.5 |
agentOspfDefaultInfoOriginateMetricConfiguredFlag to determine whether OSPF default-info originate metric
is configured or not.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.4.6 |
agentOspfDefaultInfoOriginateMetricTypeMetric Type of the default route,which OSPF advertises when learned from
other protocol. It can be 1(external type 1) or 2(external type 2).rw Enumeration .ng7000Switch.2.4.7 |
agentOspfRouteRedistTableThis table contains the MIB objects required to configure
route-redistribution for OSPF. Here, OSPF is the Destination
protocol and the source protocols can be any of : BGP, RIP,
Static, Connected. SEQUENCE OF AgentOspfRouteRedistEntry .ng7000Switch.2.4.8 |
agentOspfRouteRedistEntry AgentOspfRouteRedistEntry .ng7000Switch.2.4.8.1 |
agentOspfRouteRedistSourceSource protocol, from which OSPF can redistribute routes.
This object also acts as the identifier for the
OSPF redistribution Table entry.ro Enumeration .ng7000Switch.2.4.8.1.1 |
agentOspfRouteRedistModeUser enabels/disables route-redistribution for a particular source
protocol.rw Enumeration .ng7000Switch.2.4.8.1.2 |
agentOspfRouteRedistMetricMetric used for redistributing a particular source protocol route
into OSPF.rw Integer32 .ng7000Switch.2.4.8.1.3 |
agentOspfRouteRedistMetricConfiguredFlag to determine whether OSPF redistribute-metric is configured or not.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.4.8.1.4 |
agentOspfRouteRedistMetricTypeMetric Type of routes,which OSPF redistributes from other source protocols.
It can be 1(external type 1) or 2(external type 2).rw Enumeration .ng7000Switch.2.4.8.1.5 |
agentOspfRouteRedistTagIt specifies the tag field in routes redistributed by OSPF.rw Unsigned32 .ng7000Switch.2.4.8.1.6 |
agentOspfRouteRedistSubnetsIf this value is false, then OSPF will not redistribute subnetted routes.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.4.8.1.7 |
agentOspfRouteRedistDistListAccess-list number of the access-list, which filters routes received
from a source-protocol.rw Unsigned32 .ng7000Switch.2.4.8.1.8 |
agentOspfRouteRedistDistListConfiguredFlag to determine whether Access-list is configured or not.rw TruthValue (SNMPv2-TC) .ng7000Switch.2.4.8.1.9 |
agentOspfIfTableThe OSPF Interface Table describes the inter-
faces from the viewpoint of OSPF. Augments
ospfIfTable from the OSPF-MIB. SEQUENCE OF AgentOspfIfEntry .ng7000Switch.2.4.9 |
agentOspfIfEntryThe OSPF Interface Entry describes one inter-
face from the viewpoint of OSPF. Augments
ospfIfEntry in OSPF-MIB. AgentOspfIfEntry .ng7000Switch.2.4.9.1 |
agentOspfIfAuthKeyIdThe identifier for the authentication key used
on this interface. This field is only meaningful
when the OSPF-MIB ospfIfAuthType is md5(2);
otherwise, the value is not used.rw INTEGER .ng7000Switch.2.4.9.1.1 |
agentOspfIfIpMtuIgnoreFlagConfigures the IP MTU Ignore Flag value for this OSPF interface.rw Enumeration .ng7000Switch.2.4.9.1.2 |
agentOspfVirtIfTableInformation about this router's virtual inter-
faces. Augments ospfVirtIfTable from the OSPF-MIB. SEQUENCE OF AgentOspfVirtIfEntry .ng7000Switch.2.4.10 |
agentOspfVirtIfEntryInformation about a single Virtual Interface.
Augments ospfVirtIfEntry in OSPF-MIB. AgentOspfVirtIfEntry .ng7000Switch.2.4.10.1 |
agentOspfVirtIfAuthKeyIdThe identifier for the authentication key used
on this virtual interface. This field is only meaningful
when the OSPF-MIB ospfVirtIfAuthType is md5(2);
otherwise, the value is not used.rw INTEGER .ng7000Switch.2.4.10.1.1 |
agentRouterOspfRFC1583CompatibilityModeFrom RFC2328:
Controls the preference rules used in Section 16.4 when
choosing among multiple AS-external-LSAs advertising the
same destination. When set to 'enabled', the preference
rules remain those specified by RFC 1583 ([Ref9]). When set
to 'disabled', the preference rules are those stated in
Section 16.4.1, which prevent routing loops when AS-
external-LSAs for the same destination have been originated
from different areas. Set to 'enabled' by default.
In order to minimize the chance of routing loops, all OSPF
routers in an OSPF routing domain should have
RFC1583Compatibility set identically. When there are routers
present that have not been updated with the functionality
specified in Section 16.4.1 of this memo, all routers should
have RFC1583Compatibility set to 'enabled'. Otherwise, all
routers should have RFC1583Compatibility set to 'disabled',
preventing all routing loops.rw Enumeration .ng7000Switch.2.4.11 |
agentSnmpTrapFlagsConfigGroupLayer3 OBJECT IDENTIFIER .ng7000Switch.2.5 |
agentSnmpVRRPNewMasterTrapFlagThis flag enables the sending of VRRP new master notification
traps.rw Enumeration .ng7000Switch.2.5.1 |
agentSnmpVRRPAuthFailureTrapFlagThis flag enables the sending of VRRP authentication failure
notification traps.rw Enumeration .ng7000Switch.2.5.2 |
agentBootpDhcpRelayGroup OBJECT IDENTIFIER .ng7000Switch.2.6 |
agentBootpDhcpRelayMaxHopCountThe BOOTP/DHCP Max Hop Count.
The relay agent silently discards BOOTREQUEST messages whose hops field exceeds the value 16
assuming that the request is looped through the intermediate agents. The default value is 4.rw Integer32 .ng7000Switch.2.6.1 |
agentBootpDhcpRelayForwardingIpThe BOOTP/DHCP Server IP Address.
All the requests will be forwarded and the replies expected from this address.rw IpAddress .ng7000Switch.2.6.2 |
agentBootpDhcpRelayForwardModeThe BOOTP/DHCP Admin Mode.
The relaying functionality can be administratively enabled or disabled by this objectrw Enumeration .ng7000Switch.2.6.3 |
agentBootpDhcpRelayMinWaitTimeThe BOOTP/DHCP Minimum Wait Time.
When the BOOTP relay agent receives a BOOTREQUEST message, it MAY use the value of the 'secs'
(seconds since client began booting) field of the request as a factor in deciding whether to
relay the request or not.rw Integer32 .ng7000Switch.2.6.4 |
agentBootpDhcpRelayCircuitIdOptionModeThe BOOTP/DHCP Circuit ID Option Mode.
This flag is set to enable/disable the network element to add/remove the DHCP Relay agent
Circuit ID sub-options.rw Enumeration .ng7000Switch.2.6.5 |
agentBootpDhcpRelayNumOfRequestsReceivedThe Number of BOOTP/DHCP Requests Received.
Total number of BOOTREQUESTs received from all clients.ro Integer32 .ng7000Switch.2.6.6 |
agentBootpDhcpRelayNumOfRequestsForwardedThe Number of BOOTP/DHCP Requests Forwarded.
Total number of BOOTREQUESTs forwarded to the next agents/servers.ro Integer32 .ng7000Switch.2.6.7 |
agentBootpDhcpRelayNumOfDiscardsThe Number of BOOTP/DHCP Discards.
Total number of packets discarded by the network element because of error in the packet.ro Integer32 .ng7000Switch.2.6.8 |
agentECMPGroup OBJECT IDENTIFIER .ng7000Switch.2.7 |
agentECMPOspfMaxPathsIt sets the number of paths that OSPF can report for a given destination
where maxpaths is platform-dependent.rw Integer32 .ng7000Switch.2.7.1 |