MPLS-TE-MIB
This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft <draft-ietf-mpls- rsvp-lsp-tunnel-07.txt>, August 2000; Constraint- Based LSP Setup using LDP, B. Jamoussi, Internet Draft <draft-ietf-mpls-cr-ldp-04.txt>, July 2000; Requirements for Traffic Engineering Over MPLS, Awduche, D., J. Malcolm, J., Agogbua, J., O'Dell, M., J. McManus, <rfc2702.txt>, September 1999.
120
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
120 total| Object Name |
|---|
mplsTeMIB OBJECT IDENTIFIER .1.3.6.1.3.95 |
RFC1155-SMI Unknown .1.3.6.1.3.95 |
mplsTeScalars OBJECT IDENTIFIER .1.3.6.1.3.95.1 |
mplsTunnelConfiguredThe number of tunnels configured on this device. A
tunnel is considered configured if the
mplsTunnelRowStatus is active(1).ro Gauge .1.3.6.1.3.95.1.1 |
mplsTunnelActiveThe number of tunnels active on this device. A
tunnel is considered active if the
mplsTunnelOperStatus is up(1).ro Gauge .1.3.6.1.3.95.1.2 |
mplsTunnelTEDistProtoThe traffic engineering distribution protocol(s)
used by this LSR. Note that an LSR may support
more than one distribution protocols
simultaneously.ro OCTET STRING .1.3.6.1.3.95.1.3 |
mplsTunnelMaxHopsThe maximum number of hops that can be specified
for a tunnel on this device.ro Gauge .1.3.6.1.3.95.1.4 |
mplsTeObjects OBJECT IDENTIFIER .1.3.6.1.3.95.2 |
mplsTunnelIndexNextThis object contains the next appropriate value to
be used for mplsTunnelIndex when creating entries
in mplsTunnelTable. If the number of unassigned
entries is exhausted, a retrival operation will
return a value of 0. This object may also return
a value of 0 when the LSR is unable to accept
conceptual row creation, for example, if the
mplsTunnelTable is implemented as read-only. To
obtain the value of mplsTunnelIndex for a new
entry, the manager must first issue a management
protocol retrieval operation to obtain the current
value of this object. The agent should modify the
value to reflect the next unassigned index after
each retrieval operation. After a manager
retrieves a value the agent will determine through
its local policy when this index value will be
made available for reuse.ro INTEGER .1.3.6.1.3.95.2.1 |
mplsTunnelTableThe mplsTunnelTable allows new MPLS tunnels to be
created between an LSR and a remote endpoint, and
existing tunnels to be reconfigured or removed.
Note that only point-to-point tunnel segments are
supported, although multi-point-to-point and point-
to-multi-point connections are supported by an LSR
acting as a cross-connect. Each MPLS tunnel can
thus have one out-segment originating at this LSR
and/or one in-segment terminating at this LSR. SEQUENCE OF MplsTunnelEntry .1.3.6.1.3.95.2.2 |
mplsTunnelEntryAn entry in this table represents an MPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signaling protocol. Whenever a new entry is
created with mplsTunnelIsIf set to true(1), then a
corresponding entry is created in ifTable as well
(see RFC 2233). The ifType of this entry is
mplsTunnel(150). MplsTunnelEntry .1.3.6.1.3.95.2.2.1 |
mplsTunnelIndexUniquely identifies this row. MplsTunnelIndex -- Rsyntax INTEGER .1.3.6.1.3.95.2.2.1.1 |
mplsTunnelInstanceUniquely identifies an instance of a tunnel. It is
useful to identify multiple instances of tunnels
for the purposes of backup and parallel tunnels. MplsTunnelInstanceIndex -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.2 |
mplsTunnelIngressLSRIdThe purpose of this object is to uniquely identity
a tunnel within a network. When the MPLS
signalling protoocol is rsvp(2) this value should
mimic the Extended Tunnel Id field in the Session
object. When the MPLS signalling protoocol is
crldp(3) this value should mimic the Ingress LSR
Router ID field in the LSPID TLV object. MplsLsrId -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.3 |
mplsTunnelEgressLSRIdSpecifies the egress LSR Id.ro MplsLsrId -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.4 |
mplsTunnelNameThe canonical name assigned to the tunnel. This
name can be used to refer to the tunnel on the
LSRs console port. If mplsTunnelIsIf is set to
true then the ifName of the interface
corresponding to this tunnel should have a value
equal to mplsTunnelName. Also see the description
of ifName in RFC 2233.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.2.1.5 |
mplsTunnelDescrA textual string containing information about the
tunnel. If there is no description this object
contains a zero length string.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.2.1.6 |
mplsTunnelIsIfDenotes whether or not this tunnel corresponds to
an interface represented in the interfaces group
table. Note that if this variable is set to true
then the ifName of the interface corresponding to
this tunnel should have a value equal to
mplsTunnelName. Also see the description of
ifName in RFC 2233.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.3.95.2.2.1.7 |
mplsTunnelIfIndexIf mplsTunnelIsIf is set to true, then this value
contains the LSR-assigned ifIndex which
corresponds to an entry in the interfaces table.
Otherwise this variable should contain the value
of zero indicating that a valid ifIndex was not
assigned to this tunnel interface.ro InterfaceIndexOrZero -- Rsyntax INTEGER .1.3.6.1.3.95.2.2.1.8 |
mplsTunnelXCPointerThis variable points to a row in the mplsXCTable.
This table identifies the segments that compose
this tunnel, their characteristics, and
relationships to each other. A value of
zeroDotZero indicates that no LSP has been
associated with this tunnel yet.rw RowPointer -- Rsyntax OBJECT IDENTIFIER .1.3.6.1.3.95.2.2.1.9 |
mplsTunnelSignallingProtoThe signaling protocol, if any, which was used to
setup this tunnel.rw Enumeration .1.3.6.1.3.95.2.2.1.10 |
mplsTunnelSetupPrioIndicates the setup priority of this tunnel.rw INTEGER .1.3.6.1.3.95.2.2.1.11 |
mplsTunnelHoldingPrioIndicates the holding priority for this tunnel.rw INTEGER .1.3.6.1.3.95.2.2.1.12 |
mplsTunnelSessionAttributesThis bitmask indicates optional session values for
this tunnel. The following describes these
bitfields:
fastRerouteThis flag indicates that the any tunnel
hop may choose to reroute this tunnel without
tearing it down.
This flag permits transit routers to use a local
repair mechanism which may result in violation of
the explicit routing of this tunnel. When a fault
is detected on an adjacent downstream link or
node, a transit router can reroute traffic for
fast service restoration.
mergingPermitted This flag permits transit routers
to merge this session with other RSVP sessions for
the purpose of reducing resource overhead on
downstream transit routers, thereby providing
better network scalability.
isPersistent Indicates whether this tunnel should
be restored automatically after a failure occurs.
isPinned This flag indicates whether the loose-
routed hops of this tunnel are to be pinned.
isComputed This flag indicates whether the tunnel
path is computed using a constraint-based routing
algorithm based on the mplsTunnelHopTable entries.
recordRoute This flag indicates
whether or not the signaling protocol should
remember the tunnel path after it has been
signaled.rw OCTET STRING .1.3.6.1.3.95.2.2.1.13 |
mplsTunnelOwnerIndicates which protocol created and is
responsible for managing this tunnel. Values
rsvp(2) and crldp(3) should not be used at the
head-end of a MPLS tunnel.rw Enumeration .1.3.6.1.3.95.2.2.1.14 |
mplsTunnelLocalProtectInUseIndicates that the local repair mechanism is in
use to maintain this tunnel (usually in the face
of an outage of the link it was previously routed
over).rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.3.95.2.2.1.15 |
mplsTunnelResourcePointerThis variable represents a pointer to the traffic
parameter specification for this tunnel. This
value may point at an entry in the
mplsTunnelResourceEntry to indicate which
mplsTunnelResourceEntry is to be assigned to this
segment. This value may optionally point at an
externally defined traffic parameter specification
table. A value of zeroDotZero indicates best-
effort treatment. By having the same value of
this object, two or more segments can indicate
resource sharing.rw RowPointer -- Rsyntax OBJECT IDENTIFIER .1.3.6.1.3.95.2.2.1.16 |
mplsTunnelInstancePriorityThis value indicates which priority, in descending
order, with 0 indicating the lowest priority,
within a group of tunnel instances. A group of
tunnel instances is defined as a set of tunnels
with the same mplsTunnelIndex in this table, but
with a different mplsTunnelInstance. Tunnel group
priorities are used to denote the priority at
which a particular tunnel instance will supercede
another. Instances of tunnels containing the same
mplsTunnelInstancePriority will be used for load
sharing.rw Gauge .1.3.6.1.3.95.2.2.1.17 |
mplsTunnelHopTableIndexIndex into the mplsTunnelHopTable entry that
specifies the explicit route hops for this
tunnel.rw MplsPathIndexOrZero -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.18 |
mplsTunnelARHopTableIndexIndex into the mplsTunnelARHopTable entry that
specifies the actual hops traversed by the
tunnel.ro MplsPathIndexOrZero -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.19 |
mplsTunnelCHopTableIndexIndex into the mplsTunnelCHopTable entry that
specifies the computed hops traversed by the
tunnel.ro MplsPathIndexOrZero -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.20 |
mplsTunnelPrimaryInstanceSpecifies the instance index of the primary
instance of this tunnel.ro MplsTunnelInstanceIndex -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.21 |
mplsTunnelPrimaryTimeUpSpecifies the total time the primary instance of
this tunnel has been active. The primary instance
of this tunnel is defined in
mplsTunnelPrimaryInstance.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.3.95.2.2.1.22 |
mplsTunnelPathChangesSpecifies the number of times the paths has
changed for this tunnel.ro Counter .1.3.6.1.3.95.2.2.1.23 |
mplsTunnelLastPathChangeSpecifies the time since the last path change for
this tunnel.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.3.95.2.2.1.24 |
mplsTunnelCreationTimeSpecifies the value of SysUpTime when the first
instance of this tunnel came into existence.ro TimeStamp -- Rsyntax TimeTicks .1.3.6.1.3.95.2.2.1.25 |
mplsTunnelStateTransitionsSpecifies the number of times the state of this
tunnel instance has changed.ro Counter .1.3.6.1.3.95.2.2.1.26 |
mplsTunnelIncludeAnyAffinityA link satisfies the include-any constraint if and
only if the constraint is zero, or the link and
the constraint have a resource class in common.rw Gauge .1.3.6.1.3.95.2.2.1.27 |
mplsTunnelIncludeAllAffinityA link satisfies the include-all constraint if and
only if the link contains all of the adminstrative
groups specified in the constraint.rw Gauge .1.3.6.1.3.95.2.2.1.28 |
mplsTunnelExcludeAllAffinityA link satisfies the exclude-all constraint if and
only if the link contains none of the
adminstrative groups specifie in the constraint.rw Gauge .1.3.6.1.3.95.2.2.1.29 |
mplsTunnelPathInUseThis value denotes the configured path that was
chosen for this tunnel. This value reflects the
secondary index into the TunnelHopTable. This path
may not exactly match the one in the ARHopTable
due to the fact that some CSPF modification may
have taken place. See the ARHopTable for the
actual path being taken by the tunnel. A value of
zero denotes that no path is currently in use or
available.rw MplsPathIndexOrZero -- Rsyntax Gauge .1.3.6.1.3.95.2.2.1.30 |
mplsTunnelRoleThis value signifies the role that this tunnel
entry/instance represents. This value MUST be set
to head(1) at the originating point of the tunnel.
This value MUST be set to transit(2) at transit
points along the tunnel, if transit points are
supported. This value MUST be set to tail(3) at
the terminating point of the tunnel if tunnel
tails are supported.rw Enumeration .1.3.6.1.3.95.2.2.1.31 |
mplsTunnelTotalUpTimeThis value represents the aggregate up time for
all instances of this tunnel, if available. If
this value is unavailable, it MUST return a value
of 0.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.3.95.2.2.1.32 |
mplsTunnelInstanceUpTimeThis value identifies the total time that this
tunnel instance's operStatus has been Up(1).rw TimeTicks (SNMPv2-SMI) .1.3.6.1.3.95.2.2.1.33 |
mplsTunnelAdminStatusIndicates the desired operational status of this
tunnel.rw Enumeration .1.3.6.1.3.95.2.2.1.34 |
mplsTunnelOperStatusIndicates the actual operational status of this
tunnel, which is typically but not limited to, a
function of the state of individual segments of
this tunnel.ro Enumeration .1.3.6.1.3.95.2.2.1.35 |
mplsTunnelRowStatusThis variable is used to create, modify, and/or
delete a row in this table.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.3.95.2.2.1.36 |
mplsTunnelStorageTypeThis variable indicates the storage type for this
object.rw StorageType -- Rsyntax INTEGER { -- other(1), -- volatile(2), -- nonVolatile(3), -- permanent(4), -- readOnly(5) -- } .1.3.6.1.3.95.2.2.1.37 |
mplsTunnelHopListIndexNextThis object contains an appropriate value to be
used for mplsTunnelHopListIndex when creating
entries in the mplsTunnelHopTable. If the number
of unassigned entries is exhausted, a retrival
operation will return a value of 0. This object
may also return a value of 0 when the LSR is
unable to accept conceptual row creation, for
example, if the mplsTunnelHopTable is implemented
as read-only. To obtain the value of
mplsTunnelHopListIndex for a new entry in the
mplsTunnelHopTable, the manager issues a
management protocol retrieval operation to obtain
the current value of mplsTunnelHopIndex. After
each retrieval operation, the agent should modify
the value to reflect the next unassigned index.
After a manager retrieves a value the agent will
determine through its local policy when this index
value will be made available for reuse.ro Gauge .1.3.6.1.3.95.2.3 |
mplsTunnelHopTableThe mplsTunnelHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, when it is established via
signaling, for the outgoing direction of the
tunnel. Each row in this table is indexed by
mplsTunnelHopListIndex. Each row also has a
secondary index mplsTunnelHopIndex corresponding
to the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelHopTable. SEQUENCE OF MplsTunnelHopEntry .1.3.6.1.3.95.2.4 |
mplsTunnelHopEntryAn entry in this table represents a tunnel hop.
An entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol. MplsTunnelHopEntry .1.3.6.1.3.95.2.4.1 |
mplsTunnelHopListIndexPrimary index into this table identifying a
particular explicit route object. MplsPathIndex -- Rsyntax Gauge .1.3.6.1.3.95.2.4.1.1 |
mplsPathOptionIndexSecondary index into this table identifying a
particular group of hops representing a particular
configured path. This is otherwise known as a path
option. MplsPathIndex -- Rsyntax Gauge .1.3.6.1.3.95.2.4.1.2 |
mplsTunnelHopIndexSecondary index into this table identifying a
particular hop. MplsPathIndex -- Rsyntax Gauge .1.3.6.1.3.95.2.4.1.3 |
mplsTunnelHopAddrTypeDenotes the address type of this tunnel hop.rw Enumeration .1.3.6.1.3.95.2.4.1.4 |
mplsTunnelHopIpv4AddrIf mplsTunnelHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.rw InetAddressIPv4 -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.4.1.5 |
mplsTunnelHopIpv4PrefixLenIf mplsTunnelHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0.rw Gauge .1.3.6.1.3.95.2.4.1.6 |
mplsTunnelHopIpv6AddrIf the mplsTunnelHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0.rw InetAddressIPv6 -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.4.1.7 |
mplsTunnelHopIpv6PrefixLenIf mplsTunnelHopAddrType is set to ipV6(2), this
value will contain the prefix length for this
hop's IPv6 address. This object is otherwise
insignificant and should contain a value of 0.rw Gauge .1.3.6.1.3.95.2.4.1.8 |
mplsTunnelHopAsNumberIf mplsTunnelHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this
fact.rw Gauge .1.3.6.1.3.95.2.4.1.9 |
mplsTunnelHopLspIdIf mplsTunnelHopAddrType is set to lspid(4), then
this value will contain the LSPID of a tunnel of
this hop. The present tunnel being configured is
tunneled through this hop (using label
stacking). This object is otherwise insignificant
and should contain a value of 0 to indicate this
fact.rw MplsLSPID -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.4.1.10 |
mplsTunnelHopTypeDenotes whether this tunnel hop is routed in a
strict or loose fashion.rw Enumeration .1.3.6.1.3.95.2.4.1.11 |
mplsTunnelHopRowStatusThis variable is used to create, modify, and/or
delete a row in this table.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.3.95.2.4.1.12 |
mplsTunnelHopStorageTypeThis variable indicates the storage type for this
object.rw StorageType -- Rsyntax INTEGER { -- other(1), -- volatile(2), -- nonVolatile(3), -- permanent(4), -- readOnly(5) -- } .1.3.6.1.3.95.2.4.1.13 |
mplsTunnelResourceIndexNextThis object contains the next appropriate value to
be used for mplsTunnelResourceIndex when creating
entries in the mplsTunnelResourceTable. If the
number of unassigned entries is exhausted, a
retrival operation will return a value of 0. This
object may also return a value of 0 when the LSR
is unable to accept conceptual row creation, for
example, if the mplsTunnelTable is implemented as
read-only. To obtain the mplsTunnelResourceIndex
value for a new entry, the manager must first
issue a management protocol retrieval operation to
obtain the current value of this object. The agent
should modify the value to reflect the next
unassigned index after each retrieval operation.
After a manager retrieves a value the agent will
determine through its local policy when this index
value will be made available for reuse.ro Gauge .1.3.6.1.3.95.2.5 |
mplsTunnelResourceTableThe mplsTunnelResourceTable allows a manager to
specify which resources are desired for an MPLS
tunnel. This table also allows several tunnels to
point to a single entry in this table, implying
that these tunnels should share resources. SEQUENCE OF MplsTunnelResourceEntry .1.3.6.1.3.95.2.6 |
mplsTunnelResourceEntryAn entry in this table represents a set of
resources for an MPLS tunnel. An entry can be
created by a network administrator or by an SNMP
agent as instructed by any MPLS signaling
protocol. MplsTunnelResourceEntry .1.3.6.1.3.95.2.6.1 |
mplsTunnelResourceIndexUniquely identifies this row. Gauge .1.3.6.1.3.95.2.6.1.1 |
mplsTunnelResourceMaxRateThe maximum rate in bits/second. Note that
setting mplsTunnelResourceMaxRate,
mplsTunnelResourceMeanRate, and
mplsTunnelResourceMaxBurstSize to 0 indicates best-
effort treatment.
This object is copied to an instance of
mplsTrafficParamMaxRate in mplsTrafficParamTable
the OID of which is copied into the corresponding
mplsInSegmentTrafficParamPtr.rw MplsBitRate -- Rsyntax INTEGER .1.3.6.1.3.95.2.6.1.2 |
mplsTunnelResourceMeanRateThis object is copied into an instance of
mplsTrafficParamMeanRate in the
mplsTrafficParamTable. The OID of this table entry
is then copied into the corresponding
mplsInSegmentTrafficParamPtr.
When resource allocation is performed as requested
by this TSpec object, it is copied into an entry
in mplsTrafficParamTable [LSRMIB]:
mplsTunnelInMeanRate to mplsTrafficParamMeanRate.
The OID of this entry is copied to
mplsInSegmentTrafficParamPtr of the corresponding
in-segment entry.rw MplsBitRate -- Rsyntax INTEGER .1.3.6.1.3.95.2.6.1.3 |
mplsTunnelResourceMaxBurstSizeThe maximum burst size in bytes. This object is
copied to mplsInSegmentMaxBurstSize of the
corresponding in-segment.
When resource allocation is performed as requested
by this TSpec object, it is copied into an entry
in mplsTrafficParamTable [LSRMIB]:
mplsTunnelInMaxBurstSize to
mplsTrafficParamMaxBurstSize. The OID of this
entry is copied to mplsInSegmentTrafficParamPtr of
the corresponding in-segment entry.rw MplsBurstSize -- Rsyntax INTEGER .1.3.6.1.3.95.2.6.1.4 |
mplsTunnelResourceRowStatusThis variable is used to create, modify, and/or
delete a row in this table.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.3.95.2.6.1.5 |
mplsTunnelResourceStorageTypeThis variable indicates the storage type for this
object.rw StorageType -- Rsyntax INTEGER { -- other(1), -- volatile(2), -- nonVolatile(3), -- permanent(4), -- readOnly(5) -- } .1.3.6.1.3.95.2.6.1.6 |
mplsTunnelARHopTableThe mplsTunnelARHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as reported by the MPLS
signaling protocol, for the outgoing direction of
the tunnel. Each row in this table is indexed by
mplsTunnelARHopListIndex. Each row also has a
secondary index mplsTunnelARHopIndex,
corresponding to the next hop that this row
corresponds to. The first row in the table is the
first hop after the origination point of the
tunnel. In case we want to specify a particular
interface on the originating LSR of an outgoing
tunnel by which we want packets to exit the LSR,
we specify this as the first hop for this tunnel
in mplsTunnelARHopTable.
Please note that since the information necessary
to build entries within this table are not
provided by some MPLS signaling protocols,
implementation of this table is optional.
Furthermore, since the information in this table
is actually provided by the MPLS signaling
protocol after the path has been set-up, the
entries in this table are provided only for
observation, and hence, all variables in this
table are accessible exclusively as read-only. SEQUENCE OF MplsTunnelARHopEntry .1.3.6.1.3.95.2.7 |
mplsTunnelARHopEntryAn entry in this table represents a tunnel hop.
An entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol. MplsTunnelARHopEntry .1.3.6.1.3.95.2.7.1 |
mplsTunnelARHopListIndexPrimary index into this table identifying a
particular recorded hop list. Gauge .1.3.6.1.3.95.2.7.1.1 |
mplsTunnelARHopIndexSecondary index into this table identifying the
particular hop. Gauge .1.3.6.1.3.95.2.7.1.2 |
mplsTunnelARHopAddrTypeDenotes the address type of this tunnel hop.ro Enumeration .1.3.6.1.3.95.2.7.1.3 |
mplsTunnelARHopIpv4AddrIf mplsTunnelARHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.ro InetAddressIPv4 -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.7.1.4 |
mplsTunnelARHopIpv4PrefixLenIf mplsTunnelARHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0.ro Gauge .1.3.6.1.3.95.2.7.1.5 |
mplsTunnelARHopIpv6AddrIf the mplsTunnelARHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0.ro InetAddressIPv6 -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.7.1.6 |
mplsTunnelARHopIpv6PrefixLenIf mplsTunnelARHopAddrType is set to ipV6(2), this
value will contain the prefix length for this
hop's IPv6 address. This object is otherwise
insignificant and should contain a value of 0.ro Gauge .1.3.6.1.3.95.2.7.1.7 |
mplsTunnelARHopAsNumberIf mplsTunnelARHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this
fact.ro Gauge .1.3.6.1.3.95.2.7.1.8 |
mplsTunnelARHopTypeDenotes whether this is tunnel hop is routed in a
strict or loose fashion.ro Enumeration .1.3.6.1.3.95.2.7.1.9 |
mplsTunnelCHopTableThe mplsTunnelCHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as computed by a constraint-
based routing protocol, based on the
mplsTunnelHopTable for the outgoing direction of
the tunnel. Each row in this table is indexed by
mplsTunnelCHopListIndex. Each row also has a
secondary index mplsTunnelCHopIndex, corresponding
to the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelCHopTable.
Please note that since the information necessary
to build entries within this table may not be
supported by some LSRs, implementation of this
table is optional. Furthermore, since the
information in this table is actually provided by
routing protocol after the path has been computed,
the entries in this table are provided only for
observation, and hence, all variables in this
table are accessible exclusively as read-only. SEQUENCE OF MplsTunnelCHopEntry .1.3.6.1.3.95.2.8 |
mplsTunnelCHopEntryAn entry in this table represents a tunnel hop.
An entry in this table is created by a constraint-
based routing protocol based on the hops specified
in the corresponding mplsTunnelHopTable. MplsTunnelCHopEntry .1.3.6.1.3.95.2.8.1 |
mplsTunnelCHopListIndexPrimary index into this table identifying a
particular computed hop list. Gauge .1.3.6.1.3.95.2.8.1.1 |
mplsTunnelCHopIndexSecondary index into this table identifying the
particular hop. Gauge .1.3.6.1.3.95.2.8.1.2 |
mplsTunnelCHopAddrTypeDenotes the address type of this tunnel hop.ro Enumeration .1.3.6.1.3.95.2.8.1.3 |
mplsTunnelCHopIpv4AddrIf mplsTunnelCHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.ro InetAddressIPv4 -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.8.1.4 |
mplsTunnelCHopIpv4PrefixLenIf mplsTunnelCHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0.ro Gauge .1.3.6.1.3.95.2.8.1.5 |
mplsTunnelCHopIpv6AddrIf the mplsTunnelCHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0.ro InetAddressIPv6 -- Rsyntax OCTET STRING .1.3.6.1.3.95.2.8.1.6 |
mplsTunnelCHopIpv6PrefixLenIf mplsTunnelCHopAddrType is set to ipV6(2), this
value will contain the prefix length for this
hop's IPv6 address. This object is otherwise
insignificant and should contain a value of 0.ro Gauge .1.3.6.1.3.95.2.8.1.7 |
mplsTunnelCHopAsNumberIf mplsTunnelCHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this
fact.ro Gauge .1.3.6.1.3.95.2.8.1.8 |
mplsTunnelCHopTypeDenotes whether this is tunnel hop is routed in a
strict or loose fashion.ro Enumeration .1.3.6.1.3.95.2.8.1.9 |
mplsTunnelPerfTableThis table provides per-tunnel MPLS performance
information. SEQUENCE OF MplsTunnelPerfEntry .1.3.6.1.3.95.2.9 |
mplsTunnelPerfEntryAn entry in this table is created by the LSR for
every tunnel. Its is an extension to
mplsTunnelEntry. MplsTunnelPerfEntry .1.3.6.1.3.95.2.9.1 |
mplsTunnelPerfPacketsNumber of packets forwarded by the tunnel.ro Counter .1.3.6.1.3.95.2.9.1.1 |
mplsTunnelPerfHCPacketsHigh capacity counter for number of packets
forwarded by the tunnel.ro --?? syntax is not convertable to SMIv1 Counter .1.3.6.1.3.95.2.9.1.2 |
mplsTunnelPerfErrorsNumber of errored packets.ro Counter .1.3.6.1.3.95.2.9.1.3 |
mplsTunnelPerfBytesNumber of bytes forwarded by the tunnel.ro Counter .1.3.6.1.3.95.2.9.1.4 |
mplsTunnelPerfHCBytesHigh capacity counter for number of bytes
forwarded by the tunnel.ro --?? syntax is not convertable to SMIv1 Counter .1.3.6.1.3.95.2.9.1.5 |
mplsTunnelTrapEnableIf this object is true, then it enables the
generation of mplsTunnelUp and mplsTunnelDown
traps, otherwise these traps are not emitted.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.3.95.2.10 |
mplsTeNotifications OBJECT IDENTIFIER .1.3.6.1.3.95.3 |
mplsTeNotifyPrefix OBJECT IDENTIFIER .1.3.6.1.3.95.3.0 |
mplsTunnelUpThis notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to leave the down
state and transition into some other state (but
not into the notPresent state). This other state
is indicated by the included value of
mplsTunnelOperStatus. TRAP-TYPE .1.3.6.1.3.95.3.0.1 |
mplsTunnelDownThis notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to enter the down
state from some other state (but not from the
notPresent state). This other state is indicated
by the included value of mplsTunnelOperStatus. TRAP-TYPE .1.3.6.1.3.95.3.0.2 |
mplsTunnelReroutedThis notification is generated when a tunnel is
rerouted or re-optimized. If the Actual Path is
used, then this object MAY contain the new path
for this tunnel some time after this trap is
issued by the agent. TRAP-TYPE .1.3.6.1.3.95.3.0.3 |
mplsTeConformance OBJECT IDENTIFIER .1.3.6.1.3.95.4 |
mplsTeGroups OBJECT IDENTIFIER .1.3.6.1.3.95.4.1 |
mplsTunnelGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.1 |
mplsTunnelManualGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.2 |
mplsTunnelSignaledGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.3 |
mplsTunnelScalarGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.4 |
mplsTunnelIsIntfcGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.5 |
mplsTunnelIsNotIntfcGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.6 |
mplsTunnelOptionalGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.7 |
mplsTeNotificationGroup OBJECT IDENTIFIER .1.3.6.1.3.95.4.1.8 |
mplsTeCompliances OBJECT IDENTIFIER .1.3.6.1.3.95.4.2 |
mplsTeModuleCompliance OBJECT IDENTIFIER .1.3.6.1.3.95.4.2.1 |