MPLS-L3VPN-DRAFT-03-MIB
AI MIB Summary
The MPLS-L3VPN-DRAFT-03-MIB provides managed object definitions for monitoring Layer-3 Multiprotocol Label Switching Virtual Private Network (L3VPN) instances, specifically tracking VRF (Virtual Routing and Forwarding) table states, label binding information, and associated routing protocol adjacencies across MPLS-enabled routers. This module enables the collection of operational metrics regarding L3VPN tunnel establishment, route distribution, and label stack integrity for network fault isolation and capacity planning.
This MIB contains managed object definitions for the Layer-3 Multiprotocol Label Switching Virtual Private Networks. Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFCXXX; see the RFC itself for full legal notices.
Main OID:
mplsL3VpnMIB.1.3.6.1.2.1.10.166.1
93
Objects
Active
Status
10
Dependencies
Imported Objects
Objects
93 total| Object Name |
|---|
mplsL3VpnMIBThis MIB contains managed object definitions for the Layer-3 Multiprotocol Label Switching Virtual Private Networks. Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFCXXX; see the RFC itself for full legal notices. MODULE-IDENTITY .1.3.6.1.2.1.10.166.1 |
mplsL3VpnNotifications OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.0 |
mplsVrfIfUpThis notification is generated when: a. The ifOperStatus of an interface associated with a VRF changes to the up(1) state. b. When an interface with ifOperStatus = up(1) is associated with a VRF. NOTIFICATION-TYPE .1.3.6.1.2.1.10.166.1.0.1 |
mplsVrfIfDownThis notification is generated when: a. The ifOperStatus of an interface associated with a VRF changes to the down(1) state. b. When an interface with ifOperStatus = up(1) state is disassociated with a VRF. NOTIFICATION-TYPE .1.3.6.1.2.1.10.166.1.0.2 |
mplsNumVrfRouteMidThreshExceededThis notification is generated when the number of routes contained by the specified VRF exceeds the value indicated by mplsL3VpnVrfMidRouteThreshold. A single notification MUST be generated when this threshold is exceeded, and no other notifications of this type should be issued until the value of mplsL3VpnVrfPerfCurrNumRoutes has fallen below that of mplsL3VpnVrfConfMidRteThresh. NOTIFICATION-TYPE .1.3.6.1.2.1.10.166.1.0.3 |
mplsNumVrfRouteMaxThreshExceededThis notification is generated when the number of routes contained by the specified VRF exceeds or attempts to exceed the maximum allowed value as indicated by mplsL3VpnVrfMaxRouteThreshold. In cases where mplsL3VpnVrfConfHighRteThresh is set to the same value as mplsL3VpnVrfConfMaxRoutes, mplsL3VpnVrfConfHighRteThresh need not be exceeded; rather, just reached for this notification to be issued. Note that mplsL3VpnVrfConfRteMxThrshTime denotes the interval at which the this notification will be re-issued after the maximum value has been exceeded (or reached if mplsL3VpnVrfConfMaxRoutes and mplsL3VpnVrfConfHighRteThresh are equal) and the initial notification has been issued. This value is intended to prevent continuous generation of notifications by an agent in the event that routes are continually added to a VRF after it has reached its maximum value. The default value is 0 minutes. If this value is set to 0, the agent should only issue a single notification at the time that the maximum threshold has been reached, and should not issue any more notifications until the value of routes has fallen below the configured threshold value. NOTIFICATION-TYPE .1.3.6.1.2.1.10.166.1.0.4 |
mplsNumVrfSecIllglLblThrshExcdThis notification is generated when the number of illegal label violations on a VRF as indicated by mplsL3VpnVrfSecIllegalLblVltns has exceeded mplsL3VpnVrfSecIllLblRcvThrsh. The threshold is not included in the varbind here because the value of mplsL3VpnVrfSecIllegalLblVltns should be one greater than the threshold at the time this notification is issued. NOTIFICATION-TYPE .1.3.6.1.2.1.10.166.1.0.5 |
mplsNumVrfRouteMaxThreshClearedThis notification is generated only after the number of routes contained by the specified VRF exceeds or attempts to exceed the maximum allowed value as indicated by mplsVrfMaxRouteThreshold, and then falls below this value. The emission of this notification informs the operator that the error condition has been cleared without the operator having to query the device. Note that mplsL3VpnVrfConfRteMxThrshTime denotes the interval at which the the mplsNumVrfRouteMaxThreshExceeded notification will be re-issued after the maximum value has been exceeded (or reached if mplsL3VpnVrfConfMaxRoutes and mplsL3VpnVrfConfHighRteThresh are equal) and the initial notification has been issued. Therefore, the generation of this notification should also be emitted with this same frequency (assuming that the error condition is cleared). Specifically, if the error condition is reached and cleared several times during the period of time specified in mplsL3VpnVrfConfRteMxThrshTime, only a single notification will be issued to indicate the first instance of the error condition as well as the first time the error condition is cleared. This behavior is intended to prevent continuous generation of notifications by an agent in the event that routes are continually added and removed to/from a VRF after it has reached its maximum value. The default value is 0. If this value is set to 0, the agent should issue a notification whenever the maximum threshold has been cleared. NOTIFICATION-TYPE .1.3.6.1.2.1.10.166.1.0.6 |
mplsL3VpnObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.1 |
mplsL3VpnScalars OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.1.1 |
mplsL3VpnConfiguredVrfsThe number of VRFs which are configured on this node.ro Unsigned32 .1.3.6.1.2.1.10.166.1.1.1.1 |
mplsL3VpnActiveVrfsThe number of VRFs which are active on this node. That is, those VRFs whose corresponding mplsL3VpnVrfOperStatus object value is equal to operational (1).ro Unsigned32 .1.3.6.1.2.1.10.166.1.1.1.2 |
mplsL3VpnConnectedInterfacesTotal number of interfaces connected to a VRF.ro Unsigned32 .1.3.6.1.2.1.10.166.1.1.1.3 |
mplsL3VpnNotificationEnableIf this object is true, then it enables the generation of all notifications defined in this MIB.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.1.4 |
mplsL3VpnVrfConfMaxPossRtsDenotes maximum number of routes which the device will allow all VRFs jointly to hold. If this value is set to 0, this indicates that the device is unable to determine the absolute maximum. In this case, the configured maximum MAY not actually be allowed by the device.ro Unsigned32 .1.3.6.1.2.1.10.166.1.1.1.5 |
mplsL3VpnVrfConfRteMxThrshTimeDenotes the interval in seconds, at which the route max threshold notification may be re-issued after the maximum value has been exceeded (or has been reached if mplsL3VpnVrfConfMaxRoutes and mplsL3VpnVrfConfHighRteThresh are equal) and the initial notification has been issued. This value is intended to prevent continuous generation of notifications by an agent in the event that routes are continually added to a VRF after it has reached its maximum value. If this value is set to 0, the agent should only issue a single notification at the time that the maxium threshold has been reached, and should not issue any more notifications until the value of routes has fallen below the configured threshold value. This is the recommended default behavior.ro Unsigned32 UNITS "seconds" .1.3.6.1.2.1.10.166.1.1.1.6 |
mplsL3VpnConf OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.1.2 |
mplsL3VpnIfConfTableThis table specifies per-interface MPLS capability and associated information. SEQUENCE OF MplsL3VpnIfConfEntry .1.3.6.1.2.1.10.166.1.1.2.1 |
mplsL3VpnIfConfEntryAn entry in this table is created by an LSR for every interface capable of supporting MPLS L3VPN. Each entry in this table is meant to correspond to an entry in the Interfaces Table. MplsL3VpnIfConfEntry .1.3.6.1.2.1.10.166.1.1.2.1.1 |
mplsL3VpnIfConfIndexThis is a unique index for an entry in the mplsL3VpnIfConfTable. A non-zero index for an entry indicates the ifIndex for the corresponding interface entry in the MPLS-VPN-layer in the ifTable. Note that this table does not necessarily correspond one-to-one with all entries in the Interface MIB having an ifType of MPLS-layer; rather, only those which are enabled for MPLS L3VPN functionality. InterfaceIndex (IF-MIB) .1.3.6.1.2.1.10.166.1.1.2.1.1.1 |
mplsL3VpnIfVpnClassificationDenotes whether this link participates in a carrier-of-carrier's, enterprise, or inter-provider scenario.rw Enumeration .1.3.6.1.2.1.10.166.1.1.2.1.1.2 |
mplsL3VpnIfVpnRouteDistProtocolDenotes the route distribution protocol across the PE-CE link. Note that more than one routing protocol may be enabled at the same time, thus this object is specified as a bitmask. For example, static(5) and ospf(2) are a typical configuration.rw Bits .1.3.6.1.2.1.10.166.1.1.2.1.1.3 |
mplsL3VpnIfConfStorageTypeThe storage type for this entry.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.2.1.1.4 |
mplsL3VpnIfConfRowStatusThis variable is used to create, modify, and/or delete a row in this table. Rows in this table signify that the specified interface is associated with this VRF. If the row creation operation succeeds, the interface will have been associated with the specified VRF, otherwise the agent MUST not allow the association. If the agent only allows read-only operations on this table, it MUST create entries in this table as they are created on the device. When a row in this table is in active(1) state, no objects in that row can be modified by the agent except mplsL3VpnIfConfStorageType and mplsL3VpnIfConfRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.2.1.1.5 |
mplsL3VpnVrfTableThis table specifies per-interface MPLS L3VPN VRF Table capability and associated information. Entries in this table define VRF routing instances associated with MPLS/VPN interfaces. Note that multiple interfaces can belong to the same VRF instance. The collection of all VRF instances comprises an actual VPN. SEQUENCE OF MplsL3VpnVrfEntry .1.3.6.1.2.1.10.166.1.1.2.2 |
mplsL3VpnVrfEntryAn entry in this table is created by an LSR for every VRF capable of supporting MPLS L3VPN. The indexing provides an ordering of VRFs per-VPN interface. MplsL3VpnVrfEntry .1.3.6.1.2.1.10.166.1.1.2.2.1 |
mplsL3VpnVrfNameThe human-readable name of this VPN. This MAY be equivalent to the RFC2685 VPN-ID, but may also vary. If it is set to the VPN ID, it MUST be equivalent to the value of mplsL3VpnVrfVpnId. It is strongly recommended that all sites supporting VRFs that are part of the same VPN use the same naming convention for VRFs as well as the same VPN ID. MplsL3VpnName .1.3.6.1.2.1.10.166.1.1.2.2.1.1 |
mplsL3VpnVrfVpnIdThe VPN ID as specified in RFC 2685. If a VPN ID has not been specified for this VRF, then this variable SHOULD be set to an empty string.rw VPNId (VPN-TC-MIB) .1.3.6.1.2.1.10.166.1.1.2.2.1.2 |
mplsL3VpnVrfDescriptionThe human-readable description of this VRF.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.2.1.10.166.1.1.2.2.1.3 |
mplsL3VpnVrfRDThe route distinguisher for this VRF.rw MplsL3VpnRouteDistinguisher .1.3.6.1.2.1.10.166.1.1.2.2.1.4 |
mplsL3VpnVrfCreationTimeThe time at which this VRF entry was created.ro TimeStamp (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.2.2.1.5 |
mplsL3VpnVrfOperStatusDenotes whether a VRF is operational or not. A VRF is up(1) when at least one interface associated with the VRF, which ifOperStatus is up(1). A VRF is down(2) when: a. There does not exist at least one interface whose ifOperStatus is up(1). b. There are no interfaces associated with the VRF.ro Enumeration .1.3.6.1.2.1.10.166.1.1.2.2.1.6 |
mplsL3VpnVrfActiveInterfacesTotal number of interfaces connected to this VRF with ifOperStatus = up(1). This counter should be incremented when: a. When the ifOperStatus of one of the connected interfaces changes from down(2) to up(1). b. When an interface with ifOperStatus = up(1) is connected to this VRF. This counter should be decremented when: a. When the ifOperStatus of one of the connected interfaces changes from up(1) to down(2). b. When one of the connected interfaces with ifOperStatus = up(1) gets disconnected from this VRF.ro Unsigned32 .1.3.6.1.2.1.10.166.1.1.2.2.1.7 |
mplsL3VpnVrfAssociatedInterfacesTotal number of interfaces connected to this VRF (independent of ifOperStatus type).ro Unsigned32 .1.3.6.1.2.1.10.166.1.1.2.2.1.8 |
mplsL3VpnVrfConfMidRteThreshDenotes mid-level water marker for the number of routes which this VRF may hold.rw Unsigned32 .1.3.6.1.2.1.10.166.1.1.2.2.1.9 |
mplsL3VpnVrfConfHighRteThreshDenotes high-level water marker for the number of routes which this VRF may hold.rw Unsigned32 .1.3.6.1.2.1.10.166.1.1.2.2.1.10 |
mplsL3VpnVrfConfMaxRoutesDenotes maximum number of routes which this VRF is configured to hold. This value MUST be less than or equal to mplsL3VpnVrfConfMaxPossRts unless it is set to 0.rw Unsigned32 .1.3.6.1.2.1.10.166.1.1.2.2.1.11 |
mplsL3VpnVrfConfLastChangedThe value of sysUpTime at the time of the last change of this table entry, which includes changes of VRF parameters defined in this table or addition or deletion of interfaces associated with this VRF.ro TimeStamp (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.2.2.1.12 |
mplsL3VpnVrfConfRowStatusThis variable is used to create, modify, and/or delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.2.2.1.13 |
mplsL3VpnVrfConfStorageTypeThe storage type for this entry.rw StorageType (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.2.2.1.14 |
mplsL3VpnVrfRTTableThis table specifies per-VRF route target association. Each entry identifies a connectivity policy supported as part of a VPN. SEQUENCE OF MplsL3VpnVrfRTEntry .1.3.6.1.2.1.10.166.1.1.2.3 |
mplsL3VpnVrfRTEntryAn entry in this table is created by an LSR for each route target configured for a VRF supporting a MPLS L3VPN instance. The indexing provides an ordering per-VRF instance. MplsL3VpnVrfRTEntry .1.3.6.1.2.1.10.166.1.1.2.3.1 |
mplsL3VpnVrfRTIndexAuxiliary index for route-targets configured for a particular VRF. Unsigned32 .1.3.6.1.2.1.10.166.1.1.2.3.1.2 |
mplsL3VpnVrfRTTypeThe route target export distribution type. Enumeration .1.3.6.1.2.1.10.166.1.1.2.3.1.3 |
mplsL3VpnVrfRTThe route target distribution policy.rw MplsL3VpnRouteDistinguisher .1.3.6.1.2.1.10.166.1.1.2.3.1.4 |
mplsL3VpnVrfRTDescrDescription of the route target.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.2.1.10.166.1.1.2.3.1.5 |
mplsL3VpnVrfRTRowStatusThis variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modified by the agent except mplsL3VpnVrfRTRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.2.3.1.6 |
mplsL3VpnVrfSecTableThis table specifies per MPLS L3VPN VRF Table security features. SEQUENCE OF MplsL3VpnVrfSecEntry .1.3.6.1.2.1.10.166.1.1.2.6 |
mplsL3VpnVrfSecEntryAn entry in this table is created by an LSR for every VRF capable of supporting MPLS L3VPN. Each entry in this table is used to indicate security-related information for each VRF entry. MplsL3VpnVrfSecEntry .1.3.6.1.2.1.10.166.1.1.2.6.1 |
mplsL3VpnVrfSecIllegalLblVltnsIndicates the number of illegally received labels on this VPN/VRF.ro Counter32 .1.3.6.1.2.1.10.166.1.1.2.6.1.1 |
mplsL3VpnVrfSecIllLblRcvThrshThe number of illegally received labels above which this notification is issued.rw Unsigned32 .1.3.6.1.2.1.10.166.1.1.2.6.1.2 |
mplsL3VpnPerf OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.1.3 |
mplsL3VpnVrfPerfTableThis table specifies per MPLS L3VPN VRF Table performance information. SEQUENCE OF MplsL3VpnVrfPerfEntry .1.3.6.1.2.1.10.166.1.1.3.1 |
mplsL3VpnVrfPerfEntryAn entry in this table is created by an LSR for every VRF capable of supporting MPLS L3VPN. MplsL3VpnVrfPerfEntry .1.3.6.1.2.1.10.166.1.1.3.1.1 |
mplsL3VpnVrfPerfRoutesAddedIndicates the number of routes added to this VPN/VRF since this device has last been reset or the VRF was created, whichever came last.ro Counter32 .1.3.6.1.2.1.10.166.1.1.3.1.1.1 |
mplsL3VpnVrfPerfRoutesDeletedIndicates the number of routes removed from this VPN/VRF.ro Counter32 .1.3.6.1.2.1.10.166.1.1.3.1.1.2 |
mplsL3VpnVrfPerfCurrNumRoutesIndicates the number of routes currently used by this VRF.ro Unsigned32 .1.3.6.1.2.1.10.166.1.1.3.1.1.3 |
mplsL3VpnVrfPerfRoutesDroppedThis counter should be incremented when the number of routes contained by the specified VRF exceeds or attempts to exceed the maximum allowed value as indicated by mplsL3VpnVrfMaxRouteThreshold.ro Counter32 .1.3.6.1.2.1.10.166.1.1.3.1.1.4 |
mplsL3VpnRoute OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.1.4 |
mplsL3VpnVrfRteTableThis table specifies per-interface MPLS L3VPN VRF Table routing information. Entries in this table define VRF routing entries associated with the specified MPLS/VPN interfaces. Note that this table contains both BGP and IGP routes, as both may appear in the same VRF. SEQUENCE OF MplsL3VpnVrfRteEntry .1.3.6.1.2.1.10.166.1.1.4.1 |
mplsL3VpnVrfRteEntryAn entry in this table is created by an LSR for every route present configured (either dynamically or statically) within the context of a specific VRF capable of supporting MPLS/BGP VPN. The indexing provides an ordering of VRFs per-VPN interface. Implementors need to be aware that if the value of the mplsL3VpnVrfName (an OID) has more that 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3. MplsL3VpnVrfRteEntry .1.3.6.1.2.1.10.166.1.1.4.1.1 |
mplsL3VpnVrfRteInetCidrDestTypeThe type of the mplsL3VpnVrfRteInetCidrDest address, as defined in the InetAddress MIB. Only those address types that may appear in an actual routing table are allowed as values of this object. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.1 |
mplsL3VpnVrfRteInetCidrDestThe destination IP address of this route. The type of this address is determined by the value of the mplsL3VpnVrfRteInetCidrDestType object. The values for the index objects mplsL3VpnVrfRteInetCidrDest and mplsL3VpnVrfRteInetCidrPfxLen must be consistent. When the value of mplsL3VpnVrfRteInetCidrDest is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object mplsL3VpnVrfRteInetCidrPfxLen MUST be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.2 |
mplsL3VpnVrfRteInetCidrPfxLenIndicates the number of leading one bits which form the mask to be logical-ANDed with the destination address before being compared to the value in the mplsL3VpnVrfRteInetCidrDest field. The values for the index objects mplsL3VpnVrfRteInetCidrDest and mplsL3VpnVrfRteInetCidrPfxLen must be consistent. When the value of mplsL3VpnVrfRteInetCidrDest is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object mplsL3VpnVrfRteInetCidrPfxLen MUST be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests. InetAddressPrefixLength .1.3.6.1.2.1.10.166.1.1.4.1.1.3 |
mplsL3VpnVrfRteInetCidrPolicyThis object is an opaque object without any defined semantics. Its purpose is to serve as an additional index which may delineate between multiple entries to the same destination. The value { 0 0 } shall be used as the default value for this object. OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.1.4.1.1.4 |
mplsL3VpnVrfRteInetCidrNHopTypeThe type of the mplsL3VpnVrfRteInetCidrNextHop address, as defined in the InetAddress MIB. Value should be set to unknown(0) for non-remote routes. Only those address types that may appear in an actual routing table are allowed as values of this object. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.5 |
mplsL3VpnVrfRteInetCidrNextHopOn remote routes, the address of the next system en route. For non-remote routes, a zero length string. The type of this address is determined by the value of the mplsL3VpnVrfRteInetCidrNHopType object. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.6 |
mplsL3VpnVrfRteInetCidrIfIndexThe ifIndex value which identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.7 |
mplsL3VpnVrfRteInetCidrTypeThe type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4)refers to a route for which the next hop is not the final destination. Routes which do not result in traffic forwarding or rejection should not be displayed even if the implementation keeps them stored internally. reject(2) refers to a route which, if matched, discards the message as unreachable and returns a notification (e.g. ICMP error) to the message sender. This is used in some protocols as a means of correctly aggregating routes. blackhole(5) refers to a route which, if matched, discards the message silently.rw Enumeration .1.3.6.1.2.1.10.166.1.1.4.1.1.8 |
mplsL3VpnVrfRteInetCidrProtoThe routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.ro IANAipRouteProtocol (IANA-RTPROTO-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.9 |
mplsL3VpnVrfRteInetCidrAgeThe number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of 'too old' can be implied except through knowledge of the routing protocol by which the route was learned.ro Gauge32 .1.3.6.1.2.1.10.166.1.1.4.1.1.10 |
mplsL3VpnVrfRteInetCidrNextHopASThe Autonomous System Number of the Next Hop. The semantics of this object are determined by the routing- protocol specified in the route's mplsL3VpnVrfRteInetCidrProto value. When this object is unknown or not relevant its value should be set to zero.rw InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.11 |
mplsL3VpnVrfRteInetCidrMetric1The primary routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's mplsL3VpnVrfRteInetCidrProto value. If this metric is not used, its value should be set to -1.rw Integer32 .1.3.6.1.2.1.10.166.1.1.4.1.1.12 |
mplsL3VpnVrfRteInetCidrMetric2An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's mplsL3VpnVrfRteInetCidrProto value. If this metric is not used, its value should be set to -1.rw Integer32 .1.3.6.1.2.1.10.166.1.1.4.1.1.13 |
mplsL3VpnVrfRteInetCidrMetric3An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's mplsL3VpnVrfRteInetCidrProto value. If this metric is not used, its value should be set to -1.rw Integer32 .1.3.6.1.2.1.10.166.1.1.4.1.1.14 |
mplsL3VpnVrfRteInetCidrMetric4An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's mplsL3VpnVrfRteInetCidrProto value. If this metric is not used, its value should be set to -1.rw Integer32 .1.3.6.1.2.1.10.166.1.1.4.1.1.15 |
mplsL3VpnVrfRteInetCidrMetric5An alternate routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's mplsL3VpnVrfRteInetCidrProto value. If this metric is not used, its value should be set to -1.rw Integer32 .1.3.6.1.2.1.10.166.1.1.4.1.1.16 |
mplsL3VpnVrfRteXCPointerIndex into mplsXCTable which identifies which cross- connect entry is associated with this VRF route entry by containing the mplsXCIndex of that cross-connect entry. The string containing the single octet 0x00 indicates that a label stack is not associated with this route entry. This can be the case because the label bindings have not yet been established, or because some change in the agent has removed them. When the label stack associated with this VRF route is created by the agent, it MUST establish the associated cross-connect entry in the mplsXCTable and then set that index to the value of this object. Changes to the cross-connect object in the mplsXCTable MUST automatically be be reflected the value of this object. If this object represents a static routing entry, then the manager must ensure that this entry is also maintained consistently in the corresponding mplsXCTable as well.rw MplsIndexType (MPLS-LSR-STD-MIB) .1.3.6.1.2.1.10.166.1.1.4.1.1.17 |
mplsL3VpnVrfRteInetCidrStatusThe row status variable, used according to row installation and removal conventions. A row entry cannot be modified when the status is marked as active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.166.1.1.4.1.1.18 |
mplsL3VpnConformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.3 |
mplsL3VpnGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.3.1 |
mplsL3VpnScalarGroupCollection of scalar objects required for MPLS VPN management. Unknown .1.3.6.1.2.1.10.166.1.3.1.1 |
mplsL3VpnVrfGroupCollection of objects needed for MPLS VPN VRF management. Unknown .1.3.6.1.2.1.10.166.1.3.1.2 |
mplsL3VpnIfGroupCollection of objects needed for MPLS VPN interface management. Unknown .1.3.6.1.2.1.10.166.1.3.1.3 |
mplsL3VpnPerfGroupCollection of objects needed for MPLS VPN performance information. Unknown .1.3.6.1.2.1.10.166.1.3.1.4 |
mplsL3VpnPerfRouteGroupCollection of objects needed to track MPLS VPN routing table dropped routes. Unknown .1.3.6.1.2.1.10.166.1.3.1.5 |
mplsL3VpnSecGroupCollection of objects needed for MPLS VPN security-related information. Unknown .1.3.6.1.2.1.10.166.1.3.1.7 |
mplsL3VpnVrfRteGroupObjects required for VRF route table management. Unknown .1.3.6.1.2.1.10.166.1.3.1.8 |
mplsL3VpnVrfRTGroupObjects required for VRF route target management. Unknown .1.3.6.1.2.1.10.166.1.3.1.9 |
mplsL3VpnNotificationGroupObjects required for MPLS VPN notifications. Unknown .1.3.6.1.2.1.10.166.1.3.1.10 |
mplsL3VpnCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.166.1.3.2 |
mplsL3VpnModuleFullComplianceCompliance statement for agents that provide full support for the L3 MPLS VPN MIB Unknown .1.3.6.1.2.1.10.166.1.3.2.1 |
mplsL3VpnModuleReadOnlyCompliancCompliance requirement for implementations that only provide read-only support for L3-MPLS-VPN-STD-MIB. Such devices can then be monitored but cannot be configured using this MIB module. Unknown .1.3.6.1.2.1.10.166.1.3.2.2 |