MICOM-4400-VOICE-NETWORK-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
217
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
217 total| Object Name |
|---|
micom-2vnet OBJECT IDENTIFIER .micom-oscar.21 |
RFC1155-SMI Unknown .micom-oscar.21 |
mcmVNETDownloadFailNAME = ;
DESC = Indicates that a failure occurred while \
downloading the voice image.\
Severity Level: MAJOR.;
HELP = Downloading the voice image failed. Retry again, and if problem \
persists, please contact system admin., or field \
Personnel.; TRAP-TYPE .micom-oscar.21.0.1 |
mcmVNETOutOfOrderNAME = ;
DESC = Indicates that the DSP is not running. \
A channel reset may be required.;
HELP = DSP is not running. Reset voice channel(s). If problem still exist, \
contact sys admin. or Field Personnel.; TRAP-TYPE .micom-oscar.21.0.2 |
mcmVNETOutOfOrderRecoveredNAME = ;
DESC = Indicates recovery from the out of order condition.\
Severity Level: CRITICAL.;
HELP = DSP is running. Normal status indication.; TRAP-TYPE .micom-oscar.21.0.3 |
mcmVNETFailedToSyncUpNAME = ;
DESC = Indicates that the DSP is running, \
but unable to sync up. A channel reset \
may be required.\
Severity Level: MAJOR.;
HELP = Reset channel(s). If Synchronization is not acquired, \
contact sys admin., or Field Personnel.; TRAP-TYPE .micom-oscar.21.0.4 |
mcmVNETFailedToSyncUpRecoveredNAME = ;
DESC = Indicates recovery from the failure to \
sync up condition.\
Severity Level: INFORMATIVE. ;
HELP = Synchronization is acquired. Normal Status Indicator.; TRAP-TYPE .micom-oscar.21.0.5 |
mcmVNETNoCVMCodeImageNAME = ;
DESC = Indicates that the built image doesn't \
contain CVM code\
Severity Level: MAJOR.;
HELP = Access device code does not contain image for CVM module. \
Please contact Sys Admin., or Field Personnel. ; TRAP-TYPE .micom-oscar.21.0.6 |
mcmVNETNoTUVMCodeImageNAME = ;
DESC = Indicates that the built image doesn't \
contain TUVM code.\
Severity Level: MAJOR.;
HELP = Access device code does not contain image for TUVM module. \
Please contact Sys Admin., or Field Personnel. ; TRAP-TYPE .micom-oscar.21.0.7 |
mcmVNETNoDVMCodeImageNAME = ;
DESC = Indicates that the built image doesn't \
contain DVM code.\
Severity Level: MAJOR.;
HELP = Access device code does not contain image for DVM module. \
Please contact Sys Admin., or Field Personnel. ; TRAP-TYPE .micom-oscar.21.0.8 |
vnet-configuration OBJECT IDENTIFIER .micom-oscar.21.1 |
mcmVNETChCfgTableNAME = ;
DESC = The VNET Voice Channel Configuration table. \
(Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF McmVNETChCfgEntry .micom-oscar.21.1.1 |
mcmVNETChCfgEntryNAME = ;
DESC = An entry in the VNET Voice Channel Configuration \
table. (Operational);
HELP = ;
CAPABILITIES = ; McmVNETChCfgEntry .micom-oscar.21.1.1.1 |
mcmVNETChCfgLimIDNAME = ;
DESC = The card lim (logical interface module) number of a \
particular voice channel. Used as an index to the \
VNET Voice Channel Configuration table. (Operational);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.1.1.1 |
mcmVNETChCfgChannelIDNAME = ;
DESC = The position of the voice channel in the lim. \
Used as an index to the VNET Voice \
Channel Configuration table. (Operational);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.1.1.2 |
mcmVNETChCfgVoiceProfileNAME = ;
DESC = The value of this object indicates the profile \
to be used to configure the specified voice \
channel. (Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.1.1.3 |
mcmVNETChCfgSwitchingProfileNAME = ;
DESC = The value of this object indicates the profile \
to be used for a switching call. (Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.1.1.4 |
mcmVNETChCfgInterfaceTypeNAME = ;
DESC = The value of this object indicates the interface \
type of the specified voice channel. (Operational);
HELP = Upon powerup, the interface type will not be \
available until the DSP software is loaded and its \
status is reported.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.1.1.5 |
mcmVNETProfileCfgTableNAME = ;
DESC = The VNET Voice Profile Configuration table. \
(Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF McmVNETProfileCfgEntry .micom-oscar.21.1.2 |
mcmVNETProfileCfgEntryNAME = ;
DESC = An entry in the VNET Voice Profile Configuration \
table. (Operational);
HELP = ;
CAPABILITIES = ; McmVNETProfileCfgEntry .micom-oscar.21.1.2.1 |
mcmVNETProfileCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
number. Used as an index to the VNET Voice \
Profile Configuration table. (Operational);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.2.1.1 |
mcmVNETProfileCfgModeNAME = ;
DESC = The value of this object selects the voice \
channel signal processing. (Operational);
HELP = Can be used to set to either dual mode with \
both voice and fax, or just voice.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.2 |
mcmVNETProfileCfgDigitizingRateNAME = ;
DESC = The value of this object selects the voice \
digitizing algorithm. (Operational);
HELP = Rate at which voice is digitized in \
designated in bits per second.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.3 |
mcmVNETProfileCfgInputLevelGainNAME = ;
DESC = The value of this object selects the input \
signal gain in dB. (Operational);
HELP = For DVM, max value is 8 dB. If more than \
8 dB is configured, 8 dB will be used. \
The range for the BRI card is -15 to 15 dB.;
CAPABILITIES = ;rw INTEGER (-15..19) .micom-oscar.21.1.2.1.4 |
mcmVNETProfileCfgOutputLevelAttnNAME = ;
DESC = The value of this object selects the output \
signal attenuation in dB. (Operational);
HELP = For DVM, max value is 8 dB. If more than \
8 dB is configured, 8 dB will be used. \
The range for the BRI card is -15 to 15dB.;
CAPABILITIES = ;rw INTEGER (-15..25) .micom-oscar.21.1.2.1.5 |
mcmVNETProfileCfgBusyOutModeNAME = ;
DESC = The value of this object selects the voice \
channel busy out control type. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.6 |
mcmVNETProfileCfgBandwidthNAME = ;
DESC = The value of this object selects the voice \
channel link bandwidth reservation style. \
(Operational);
HELP = 2 is used for forced connects or PVCs only. \
1 is used for switched connects.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.7 |
mcmVNETProfileCfgBackgroundNAME = ;
DESC = The value of this object selects the voice \
channel background noise generation type. \
(Operational);
HELP = The ability of passing background noise or \
silencing the channel during idle periods. \
First option allows the background noise to be \
regenerated during the periods, whereas the \
second option suppresses background noise during \
idle periods.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.8 |
mcmVNETProfileCfgBRIPulseRateNAME = ;
DESC = The value of this object selects the voice \
channel pulse rate in pulses per second. \
(Operational);
HELP = NOTE: This object is used by the Partner card \
and not for the ISDN BRI voice card.;
CAPABILITIES = ;rwobsolete Enumeration .micom-oscar.21.1.2.1.9 |
mcmVNETProfileCfgEMSigFormatNAME = ;
DESC = The value of this object specifies the voice \
channel E&M signaling format. (Operational);
HELP = 2 and 3 are used for force connects only. \
1 (DC) is used for switched connects.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.10 |
mcmVNETProfileCfgFXSSigFormatNAME = ;
DESC = The value of this object specifies the voice \
channel FXS signaling format. (Operational);
HELP = 1 is used for force connects only. \
2 is used for switched connects.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.11 |
mcmVNETProfileCfgDVMSigFormatNAME = ;
DESC = The value of this object specifies the voice \
channel DVM signaling format. (Operational);
HELP = 3 and 4 are used for force connects only. \
1 is used for switched connects.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.12 |
mcmVNETProfileCfgNumberOfRingsNAME = ;
DESC = The value of this object specifies when the \
voice channel (FXO or 3-port) will answer \
the call request. (Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.2.1.13 |
mcmVNETProfileCfgEMAnalOperNAME = ;
DESC = The value of this object specifies the E&M \
voice channel operation as either 2 or 4 wire \
operation. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.14 |
mcmVNETProfileCfgRingingFreqNAME = ;
DESC = The value of this object specifies the voice \
channel (FXS or 3-port) ringing frequency. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.15 |
mcmVNETProfileCfgFaxDigRateNAME = ;
DESC = The value of this object selects the voice \
channel Fax digitizing rate in bits per second. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.16 |
mcmVNETProfileCfgDiscSupervisionNAME = ;
DESC = The value of this object selects the voice \
channel method to detect the line disconnect. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.17 |
mcmVNETProfileCfgLineImpedanceNAME = ;
DESC = The value of this object selects the voice \
channel type of line impedance. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.18 |
mcmVNETProfileCfgMaxOutputLevelNAME = ;
DESC = The value of this object specifies the voice \
channel maximum output level. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.19 |
mcmVNETProfileCfgRegenDelayNAME = ;
DESC = The value of this object specifies the voice \
channel time (in seconds) to delay before dialing \
out the number (i.e., time to wait for dial tone). \
(Operational);
HELP = NOTE: This object is not required for the ISDN BRI \
voice card;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.2.1.20 |
mcmVNETProfileCfgDialDigTimeLimitNAME = ;
DESC = The value of this object specifies the voice \
channel inter-digit time-out time (in seconds). \
(Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.2.1.21 |
mcmVNETProfileCfgMaxNumForDigNAME = ;
DESC = The value of this object specifies the voice \
channel maximum number of digits that can \
be dialed. (Operational);
HELP = 0 is used for auto-call functionality.;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.2.1.22 |
mcmVNETProfileCfgRegenFormatNAME = ;
DESC = The value of this object specifies the voice \
channel dial digit regeneration format. \
(Operational);
HELP = NOTE: This object is not required for the ISDN \
BRI voice card.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.23 |
mcmVNETProfileCfgCallProgToneNAME = ;
DESC = The value of this object specifies the voice \
channel call progress tone required for different \
countries or areas. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.24 |
mcmVNETProfileCfgDTMFDetectorNAME = ;
DESC = The value of this object specifies to the voice \
channel whether to turn on or off the DTMF \
detector. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.25 |
mcmVNETProfileCfgJittersNAME = ;
DESC = The value of this object specifies the voice \
channel maximum jitters delay (in milliseconds). \
(Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.2.1.26 |
mcmVNETProfileCfgEchoCancellerNAME = ;
DESC = The value of this object specifies to the voice \
channel whether to turn on or off the echo \
canceller. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.27 |
mcmVNETProfileCfgAutoGainControlNAME = ;
DESC = The value of this object specifies to the voice \
channel whether to automatically set the input \
signal level. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.28 |
mcmVNETProfileCfgCompanderFormatNAME = ;
DESC = The value of this object specifies the voice \
channel (DVM or BRI) compander type. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.29 |
mcmVNETProfileCfgPremiumVoiceNAME = ;
DESC = The value of this object specifies to the voice \
channel (DVM) whether to enable or disable the \
transparent voice (no compression) algorithm. \
(Operational);
HELP = This object is also used by the ISDN BRI voice card \
to enable/disable Digital Lossless Switching Pattern \
Generation and Pattern Search.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.30 |
mcmVNETProfileCfgEndOfDialCharNAME = ;
DESC = The value of this object specifies to the voice \
channel whether '#' is used to end a dialing input. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.31 |
mcmVNETProfileCfgBckGrndNoiseLevelNAME = ;
DESC = Signal input above this level is considered\
a voiced signal, below this level, the \
Voice Activity Detector (VAD), will \
determine if it is a voiced signal or \
background noise.
(Operational);
HELP = Refer to the International \
Telecommunication Union(ITU-T) G.711 \
document for more information;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.32 |
mcmVNETProfileCfgSilenceHngOvrTimeNAME = ;
DESC = Indicates the time delay to switch \
from voice to silence.\
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.33 |
mcmVNETProfileCfgIdlePatternNAME = ;
DESC = The value of this object represents the \
Idle pattern on the line when no call is up.\
Specific to a PBX. This is a permanent DSP \
configuration parameter;
HELP = This value can be used to detect that a call \
has finished and that the echo canceller should \
be reset and that fax mode should be terminated.;
CAPABILITIES = ;rw INTEGER ( 0..255 ) .micom-oscar.21.1.2.1.34 |
mcmVNETProfileCfgEcanFilterLengthNAME = ;
DESC = The value of this object specifies the filter \
length for echo canceller. This is a permanent \
DSP configuration parameter.;
HELP = A length of 128 is equal to 16ms.\
A length of 256 is equal to 32ms.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.35 |
mcmVNETProfileCfgEcanErlImprovementNAME = ;
DESC = The value of this object is used for echo \
canceller Er1 improvement. This is a DSP \
Dynamic configuration parameter. \
A signal will be attenuated by this dB \
amount before being passed through the \
echo canceller. After the echo canceller, \
it will be amplified by this same dB amount, \
for a net gain of 0 dB. \
This attenuation amplicfication cycle reduces \
the resolution of the signal ( -18 ..0 ).;
HELP = ;
CAPABILITIES = ;rw INTEGER ( -18..0 ) .micom-oscar.21.1.2.1.36 |
mcmVNETProfileCfgNoiseFloorOffsetNAME = ;
DESC = The value of this object will suppress the \
impulsive backround noise in order to achieve \
silence suppression savings.
HELP = ;
CAPABILITIES = ;rw INTEGER ( 0..255 ) .micom-oscar.21.1.2.1.37 |
mcmVNETProfileCfgDtmfGenBurstLengthNAME = ;
DESC = DTMF burst generation in milliseconds.;
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.38 |
mcmVNETProfileCfgDtmRegenBurstLengthNAME = ;
DESC = DTMF burst Regeneration length in milliseconds.;
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.2.1.39 |
mcmVNETSwProfCfgTableNAME = ;
DESC = The VNET Voice Switching Profile Configuration \
table.(Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF McmVNETSwProfCfgEntry .micom-oscar.21.1.3 |
mcmVNETSwProfCfgEntryNAME = ;
DESC = An entry in the VNET Voice Switching Profile \
Configuration table. (Operational);
HELP = ;
CAPABILITIES = ; McmVNETSwProfCfgEntry .micom-oscar.21.1.3.1 |
mcmVNETSwProfCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
number. Used as an index to the VNET Voice \
Switching Profile Configuration table. \
(Operational);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.3.1.1 |
mcmVNETSwProfCfgOutCallRestrictNAME = ;
DESC = The value of this object specifies how to \
handle outgoing calls for voice channel \
switching. (Operational);
HELP = 2: include CUG ID in outgoing call. \
3: include restriction class in outgoing call. \
4: include both CUG ID and restriction \
class in outgoing call. \
5: outgoing call is not allowed.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.3.1.2 |
mcmVNETSwProfCfgInCallRestrictNAME = ;
DESC = The value of this object specifies how to \
handle incoming calls for voice channel \
switching. (Operational);
HELP = 2: check CUG ID in incoming call. (Must \
match our CUG ID for call acceptance. \
3: check RCC in incoming call. (Must be \
greater than or equal to our RCC for call \
acceptance. \
4: check both CUG and RCC in incoming \
call. \
5: incoming call is not allowed.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.3.1.3 |
mcmVNETSwProfCfgCUGIDNAME = ;
DESC = The value of this object assigns the Closed \
User Group ID for a voice channel. (Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.3.1.4 |
mcmVNETSwProfCfgRestrictClassCdNAME = ;
DESC = The value of this object assigns the Restriction \
Class Code for a voice channel. (Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.3.1.5 |
mcmVNETSwProfCfgAutoCallEntNumNAME = ;
DESC = The value of this object provides a voice \
channel Auto Call destination number by \
specifying an index into the ingress table. \
(Operational);
HELP = 0: auto call disabled. \
1-32: index to the ingress table entry where \
the dial number is specified. \
The auto call for the ISDN BRI voice card is \
always disabled.;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.3.1.6 |
mcmVNETSwProfCfgCallNegStrategyNAME = ;
DESC = The value of this object specifies the preference \
for the voice algorithm when an outgoing call is \
made. (Operational);
HELP = specific: whatever is configured. \
bandwidth: bigger block size. \
delay: shorter block size.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.3.1.7 |
mcmVNETSwProfCfgTransmitPriorityNAME = ;
DESC = The value of this object assigns the priority \
of the voice data to be transmitted. (Operational);
HELP = 0: lowest priority. \
15: highest priority.;
CAPABILITIES = ;rw INTEGER .micom-oscar.21.1.3.1.8 |
mcmVNETSwProfCfgAutoCallTypeNAME = ;
DESC = Indicates the type of auto-call \
switching to be performed by the \
voice channel.;
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.3.1.9 |
mcmVNETSwProfCfgAddServerSelectNAME = ;
DESC = Indicates which DNA server is used.;
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.3.1.10 |
mcmVNETSwProfCfgOutCallModeNAME = ;
DESC = Indicates the type of call being made.;
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.1.3.1.11 |
mcmVNETIngressDigFilterTableNAME = ;
DESC = The VNET Voice Ingress Digit Filtering \
Configuration table. (Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF McmVNETIngressDigFilterEntry .micom-oscar.21.1.4 |
mcmVNETIngressDigFilterEntryNAME = ;
DESC = An entry in the VNET Voice Ingress Digit \
Filtering Configuration table. (Operational);
HELP = ;
CAPABILITIES = ; McmVNETIngressDigFilterEntry .micom-oscar.21.1.4.1 |
mcmVNETIngressDigFilterIndexNAME = ;
DESC = The value of this object indicates the index to \
the ingress table. Used as an index to the VNET \
Voice Ingress Digit Filtering Configuration table. \
Operational);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.4.1.1 |
mcmVNETIngressDigFilterIngressNumNAME = ;
DESC = The value of this object selects the digit \
pattern to be matched. (Null terminated \
character string.) (Operational);
HELP = Valid characters are decimal digits, '#', \
'*', '+', '[' and ']' .;
CAPABILITIES = ;rw DisplayString .micom-oscar.21.1.4.1.2 |
mcmVNETIngressDigFilterManipStringNAME = ;
DESC = The value of this object selects commands \
to produce the ingress digits for speed dial, \
call redirect, and source ID insertion features. \
(Operational);
HELP = Valid characters are decimal digits, '#', \
'*', 'D', and 'I'.;
CAPABILITIES = ;rw DisplayString .micom-oscar.21.1.4.1.3 |
mcmVNETEgressDigManipTableNAME = ;
DESC = The VNET Voice Egress Digit Manipulation \
Configuration table. (Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF McmVNETEgressDigManipEntry .micom-oscar.21.1.5 |
mcmVNETEgressDigManipEntryNAME = ;
DESC = An entry in the VNET Voice Egress Digit \
Manipulation Configuration table. (Operational);
HELP = ;
CAPABILITIES = ; McmVNETEgressDigManipEntry .micom-oscar.21.1.5.1 |
mcmVNETEgressDigManipIndexNAME = ;
DESC = The value of this object indicates the index to \
the egress table. Used as an index to the VNET \
Voice Egress Digit Manipulation Configuration \
table. Operational);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.5.1.1 |
mcmVNETEgressDigManipPhoneNumNAME = ;
DESC = The value of this object selects the phone \
number that voice channels are associated with. \
This is the number to be registered to the Address \
Server (RSA). (Operational);
HELP = Valid characters are decimal digits, '#', and '*'.;
CAPABILITIES = ;rw DisplayString .micom-oscar.21.1.5.1.2 |
mcmVNETEgressDigManipStringNAME = ;
DESC = The value of this object selects commands \
to produce the egress digits for FXO, E&M, \
or FXS 3-Port interface. The result is the \
number to be sent to the connected phone \
device. (Operational);
HELP = Valid characters are decimal digits, '#', '*', \
'+', 'D', 'H', and 'I'. The character 'H' is used \
used to trigger immediate dial handling by the PBX.;
CAPABILITIES = ;rw DisplayString .micom-oscar.21.1.5.1.3 |
mcmVNETEgressDigManipChIDListNAME = ;
DESC = The value of this object selects voice channels \
associated with the phone number. The valid \
string consists of the substring 'B1'~'B6', \
'C1'~'C12', 'D1'~'D12', and 'E1'~'E2'. \
(Operational);
HELP = Valid characters are decimal digits, 'B', 'C', \
'D', and 'E'.;
CAPABILITIES = ;rw DisplayString .micom-oscar.21.1.5.1.4 |
nvmVNETChCfgTableNAME = ;
DESC = The VNET Voice Channel Configuration table. \
(Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF NvmVNETChCfgEntry .micom-oscar.21.1.6 |
nvmVNETChCfgEntryNAME = ;
DESC = An entry in the VNET Voice Channel Configuration \
table. (Configuration);
HELP = ;
CAPABILITIES = ; NvmVNETChCfgEntry .micom-oscar.21.1.6.1 |
nvmVNETChCfgLimIDNAME = ;
DESC = The card lim (logical interface module) number of a \
particular voice channel. Used as an index to the \
VNET Voice Channel Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.6.1.1 |
nvmVNETChCfgChannelIDNAME = ;
DESC = The position of the voice channel in the lim. \
Used as an index to the VNET Voice \
Channel Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.6.1.2 |
nvmVNETChCfgVoiceProfileNAME = ;
DESC = The value of this object indicates the profile \
to be used to configure the specified voice \
channel. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.6.1.3 |
nvmVNETChCfgSwitchingProfileNAME = ;
DESC = The value of this object indicates the profile \
to be used for a switching call. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.6.1.4 |
nvmVNETChCfgInterfaceTypeNAME = ;
DESC = The value of this object indicates the interface \
type of the specified voice channel. (Configuration);
HELP = Upon powerup, the interface type will not be \
available until the DSP software is loaded and its \
status is reported.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.6.1.5 |
nvmVNETProfileCfgTableNAME = ;
DESC = The VNET Voice Profile Configuration table. \
(Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF NvmVNETProfileCfgEntry .micom-oscar.21.1.7 |
nvmVNETProfileCfgEntryNAME = ;
DESC = An entry in the VNET Voice Profile Configuration \
table. (Configuration);
HELP = ;
CAPABILITIES = ; NvmVNETProfileCfgEntry .micom-oscar.21.1.7.1 |
nvmVNETProfileCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
number. Used as an index to the VNET Voice \
Profile Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.7.1.1 |
nvmVNETProfileCfgModeNAME = ;
DESC = The value of this object selects the voice \
channel signal processing. (Configuration);
HELP = Can be used to set to either dual mode with \
both voice and fax, or just voice.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.2 |
nvmVNETProfileCfgDigitizingRateNAME = ;
DESC = The value of this object selects the voice \
digitizing algorithm. (Configuration);
HELP = Rate at which voice is digitized in \
designated in bits per second.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.3 |
nvmVNETProfileCfgInputLevelGainNAME = ;
DESC = The value of this object selects the input \
signal gain in dB. (Configuration);
HELP = For DVM, max value is 8 dB. If more than \
8 dB is configured, 8 dB will be used.\
The ISDN BRI voice card range is -15 to 15dB.;
CAPABILITIES = ;ro INTEGER (-15..19) .micom-oscar.21.1.7.1.4 |
nvmVNETProfileCfgOutputLevelAttnNAME = ;
DESC = The value of this object selects the output \
signal attenuation in dB. (Configuration);
HELP = For DVM, max value is 8 dB. If more than \
8 dB is configured, 8 dB will be used.;
CAPABILITIES = ;ro INTEGER (-15..25) .micom-oscar.21.1.7.1.5 |
nvmVNETProfileCfgBusyOutModeNAME = ;
DESC = The value of this object selects the voice \
channel busy out control type. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.6 |
nvmVNETProfileCfgBandwidthNAME = ;
DESC = The value of this object selects the voice \
channel link bandwidth reservation style. \
(Configuration);
HELP = 2 is used for forced connects or PVCs only. \
1 is used for switched connects.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.7 |
nvmVNETProfileCfgBackgroundNAME = ;
DESC = The value of this object selects the voice \
channel background noise generation type. \
(Configuration);
HELP = The ability of passing background noise or \
silencing the channel during idle periods. \
First option allows the background noise to be \
regenerated during the periods, whereas the \
second option suppresses background noise during \
idle periods.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.8 |
nvmVNETProfileCfgBRIPulseRateNAME = ;
DESC = The value of this object selects the voice \
channel pulse rate in pulses per second. \
(Configuration);
HELP = NOTE: This object is used by the Partner Card, \
not by the ISDN BRI voice card.;
CAPABILITIES = ;roobsolete Enumeration .micom-oscar.21.1.7.1.9 |
nvmVNETProfileCfgEMSigFormatNAME = ;
DESC = The value of this object specifies the voice \
channel E&M signaling format. (Configuration);
HELP = 2 and 3 are used for force connects only. \
1 (DC) is used for switched connects.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.10 |
nvmVNETProfileCfgFXSSigFormatNAME = ;
DESC = The value of this object specifies the voice \
channel FXS signaling format. (Configuration);
HELP = 1 is used for force connects only. \
2 is used for switched connects.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.11 |
nvmVNETProfileCfgDVMSigFormatNAME = ;
DESC = The value of this object specifies the voice \
channel DVM signaling format. (Configuration);
HELP = 3 and 4 are used for force connects only. \
1 is used for switched connects.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.12 |
nvmVNETProfileCfgNumberOfRingsNAME = ;
DESC = The value of this object specifies when the \
voice channel (FXO or 3-port) will answer \
the call request. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.7.1.13 |
nvmVNETProfileCfgEMAnalOperNAME = ;
DESC = The value of this object specifies the E&M \
voice channel operation as either 2 or 4 wire \
operation. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.14 |
nvmVNETProfileCfgRingingFreqNAME = ;
DESC = The value of this object specifies the voice \
channel (FXS or 3-port) ringing frequency. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.15 |
nvmVNETProfileCfgFaxDigRateNAME = ;
DESC = The value of this object selects the voice \
channel Fax digitizing rate in bits per second. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.16 |
nvmVNETProfileCfgDiscSupervisionNAME = ;
DESC = The value of this object selects the voice \
channel method to detect the line disconnect. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.17 |
nvmVNETProfileCfgLineImpedanceNAME = ;
DESC = The value of this object selects the voice \
channel type of line impedance. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.18 |
nvmVNETProfileCfgMaxOutputLevelNAME = ;
DESC = The value of this object specifies the voice \
channel maximum output level. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.19 |
nvmVNETProfileCfgRegenDelayNAME = ;
DESC = The value of this object specifies the voice \
channel time (in seconds) to delay before dialing \
out the number (i.e., time to wait for dial tone). \
(Configuration);
HELP = NOTE : This object is not used for the ISDN BRI \
voice card.;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.7.1.20 |
nvmVNETProfileCfgDialDigTimeLimitNAME = ;
DESC = The value of this object specifies the voice \
channel inter-digit time-out time (in seconds). \
(Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.7.1.21 |
nvmVNETProfileCfgMaxNumForDigNAME = ;
DESC = The value of this object specifies the voice \
channel maximum number of digits that can \
be dialed. (Configuration);
HELP = 0 is used for auto-call functionality.;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.7.1.22 |
nvmVNETProfileCfgRegenFormatNAME = ;
DESC = The value of this object specifies the voice \
channel dial digit regeneration format. \
(Configuration);
HELP = NOTE: THIS object is not used for the ISDN \
BRI voice card.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.23 |
nvmVNETProfileCfgCallProgToneNAME = ;
DESC = The value of this object specifies the voice \
channel call progress tone required for different \
countries or areas. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.24 |
nvmVNETProfileCfgDTMFDetectorNAME = ;
DESC = The value of this object specifies to the voice \
channel whether to turn on or off the DTMF \
detector. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.25 |
nvmVNETProfileCfgJittersNAME = ;
DESC = The value of this object specifies the voice \
channel maximum jitters delay (in milliseconds). \
(Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.7.1.26 |
nvmVNETProfileCfgEchoCancellerNAME = ;
DESC = The value of this object specifies to the voice \
channel whether to turn on or off the echo \
canceller. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.27 |
nvmVNETProfileCfgAutoGainControlNAME = ;
DESC = The value of this object specifies to the voice \
channel whether to automatically set the input \
signal level. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.28 |
nvmVNETProfileCfgCompanderFormatNAME = ;
DESC = The value of this object specifies the voice \
channel (DVM or BRI) compander type. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.29 |
nvmVNETProfileCfgPremiumVoiceNAME = ;
DESC = The value of this object specifies to the voice \
channel (DVM) whether to enable or disable the \
transparent voice (no compression) algorithm. \
(Configuration);
HELP = This object is also used by the ISDN BRI voice \
card to enable/disable Digital Lossless Switching \
Pattern Generation and Pattern Search.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.30 |
nvmVNETProfileCfgEndOfDialCharNAME = ;
DESC = The value of this object specifies to the voice \
channel whether '#' is used to end a dialing input. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.31 |
nvmVNETProfileCfgBckGrndNoiseLevelNAME = ;
DESC = Signal input above this level is considered\
a voiced signal, below this level, the \
Voice Activity Detector (VAD), will \
determine if it is a voiced signal or \
background noise.
(Configuration);
HELP = Refer to the International \
Telecommunication Union(ITU-T) G.711 \
document for more information;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.32 |
nvmVNETProfileCfgSilenceHngOvrTimeNAME = ;
DESC = Indicates the time delay to switch \
from voice to silence.\
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.33 |
nvmVNETProfileCfgIdlePatternNAME = ;
DESC = The value of this object represents the \
Idle pattern on the line when no call is up.\
Specific to a PBX. This is a permanent DSP \
configuration parameter;
HELP = This value can be used to detect that a call \
has finished and that the echo canceller should \
be reset and that fax mode should be terminated.;
CAPABILITIES = ;ro INTEGER ( 0..255 ) .micom-oscar.21.1.7.1.34 |
nvmVNETProfileCfgEcanFilterLengthNAME = ;
DESC = The value of this object specifies the filter \
length for echo canceller. This is a permanent \
DSP configuration parameter.;
HELP = A length of 128 is equal to 16ms.\
A length of 256 is equal to 32ms.;
NOTE: The ISDN BRI voice card supports 32ms only;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.35 |
nvmVNETProfileCfgEcanErlImprovementNAME = ;
DESC = The value of this object is used for echo \
canceller Er1 improvement. This is a DSP \
Dynamic configuration parameter. \
A signal will be attenuated by this dB \
amount before being passed through the \
echo canceller. After the echo canceller, \
it will be amplified by this same dB amount, \
for a net gain of 0 dB. \
This attenuation amplicfication cycle reduces \
the resolution of the signal ( -18 ..0 ).;
HELP = ;
CAPABILITIES = ;ro INTEGER ( -18..0 ) .micom-oscar.21.1.7.1.36 |
nvmVNETProfileCfgNoiseFloorOffsetNAME = ;
DESC = The value of this object will suppress the \
impulsive backround noise in order to achieve \
silence suppression savings.
HELP = ;
CAPABILITIES = ;ro INTEGER ( 0..255 ) .micom-oscar.21.1.7.1.37 |
nvmVNETProfileCfgDtmfGenBurstLengthNAME = ;
DESC = DTMF burst generation in milliseconds.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.38 |
nvmVNETProfileCfgDtmRegenBurstLengthNAME = ;
DESC = DTMF burst Regeneration length in milliseconds.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.7.1.39 |
nvmVNETSwProfCfgTableNAME = ;
DESC = The VNET Voice Switching Profile Configuration \
table.(Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF NvmVNETSwProfCfgEntry .micom-oscar.21.1.8 |
nvmVNETSwProfCfgEntryNAME = ;
DESC = An entry in the VNET Voice Switching Profile \
Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ; NvmVNETSwProfCfgEntry .micom-oscar.21.1.8.1 |
nvmVNETSwProfCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
number. Used as an index to the VNET Voice \
Switching Profile Configuration table. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.8.1.1 |
nvmVNETSwProfCfgOutCallRestrictNAME = ;
DESC = The value of this object specifies how to \
handle outgoing calls for voice channel \
switching. (Configuration);
HELP = 2: include CUG ID in outgoing call. \
3: include restriction class in outgoing call. \
4: include both CUG ID and restriction \
class in outgoing call. \
5: outgoing call is not allowed.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.8.1.2 |
nvmVNETSwProfCfgInCallRestrictNAME = ;
DESC = The value of this object specifies how to \
handle incoming calls for voice channel \
switching. (Configuration);
HELP = 2: check CUG ID in incoming call. (Must \
match our CUG ID for call acceptance. \
3: check RCC in incoming call. (Must be \
greater than or equal to our RCC for call \
acceptance. \
4: check both CUG and RCC in incoming \
call. \
5: incoming call is not allowed.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.8.1.3 |
nvmVNETSwProfCfgCUGIDNAME = ;
DESC = The value of this object assigns the Closed \
User Group ID for a voice channel. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.8.1.4 |
nvmVNETSwProfCfgRestrictClassCdNAME = ;
DESC = The value of this object assigns the Restriction \
Class Code for a voice channel. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.8.1.5 |
nvmVNETSwProfCfgAutoCallEntNumNAME = ;
DESC = The value of this object provides a voice \
channel Auto Call destination number by \
specifying an index into the ingress table. \
(Configuration);
HELP = 0: auto call disabled. \
1-32: index to the ingress table entry where \
the dial number is specified. \
The auto call for the ISDN BRI voice card is always \
disabled.;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.8.1.6 |
nvmVNETSwProfCfgCallNegStrategyNAME = ;
DESC = The value of this object specifies the preference \
for the voice algorithm when an outgoing call is \
made. (Configuration);
HELP = specific: whatever is configured. \
bandwidth: bigger block size. \
delay: shorter block size.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.8.1.7 |
nvmVNETSwProfCfgTransmitPriorityNAME = ;
DESC = The value of this object assigns the priority \
of the voice data to be transmitted. (Configuration);
HELP = 0: lowest priority. \
15: highest priority.;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.8.1.8 |
nvmVNETSwProfCfgAutoCallTypeNAME = ;
DESC = Indicates the type of auto-call \
switching to be performed by the \
voice channel.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.8.1.9 |
nvmVNETSwProfCfgAddServerSelectNAME = ;
DESC = Indicates which DNA server is used.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.8.1.10 |
nvmVNETSwProfCfgOutCallModeNAME = ;
DESC = Indicates the type of call being made.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.1.8.1.11 |
nvmVNETIngressDigFilterTableNAME = ;
DESC = The VNET Voice Ingress Digit Filtering \
Configuration table. (Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF NvmVNETIngressDigFilterEntry .micom-oscar.21.1.9 |
nvmVNETIngressDigFilterEntryNAME = ;
DESC = An entry in the VNET Voice Ingress Digit \
Filtering Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ; NvmVNETIngressDigFilterEntry .micom-oscar.21.1.9.1 |
nvmVNETIngressDigFilterIndexNAME = ;
DESC = The value of this object indicates the index to \
the ingress table. Used as an index to the VNET \
Voice Ingress Digit Filtering Configuration table. \
Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.9.1.1 |
nvmVNETIngressDigFilterIngressNumNAME = ;
DESC = The value of this object selects the digit \
pattern to be matched. (Null terminated \
character string.) (Configuration);
HELP = Valid characters are decimal digits, '#', \
'*', '+', '[' and ']' .;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.1.9.1.2 |
nvmVNETIngressDigFilterManipStringNAME = ;
DESC = The value of this object selects commands \
to produce the ingress digits for speed dial, \
call redirect, and source ID insertion features. \
(Configuration);
HELP = Valid characters are decimal digits, '#', \
'*', 'D', and 'I'.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.1.9.1.3 |
nvmVNETEgressDigManipTableNAME = ;
DESC = The VNET Voice Egress Digit Manipulation \
Configuration table. (Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF NvmVNETEgressDigManipEntry .micom-oscar.21.1.10 |
nvmVNETEgressDigManipEntryNAME = ;
DESC = An entry in the VNET Voice Egress Digit \
Manipulation Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ; NvmVNETEgressDigManipEntry .micom-oscar.21.1.10.1 |
nvmVNETEgressDigManipIndexNAME = ;
DESC = The value of this object indicates the index to \
the egress table. Used as an index to the VNET \
Voice Egress Digit Manipulation Configuration \
table. Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.1.10.1.1 |
nvmVNETEgressDigManipPhoneNumNAME = ;
DESC = The value of this object selects the phone \
number that voice channels are associated with. \
This is the number to be registered to the Address \
Server (RSA). (Configuration);
HELP = Valid characters are decimal digits, '#', and '*'.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.1.10.1.2 |
nvmVNETEgressDigManipStringNAME = ;
DESC = The value of this object selects commands \
to produce the egress digits for FXO, E&M, \
or FXS 3-Port interface. The result is the \
number to be sent to the connected phone \
device. (Configuration);
HELP = Valid characters are decimal digits, '#', '*', \
'+', 'D', 'H', and 'I'. The character 'H' is \
used to trigger immediate dial handling by the PBX.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.1.10.1.3 |
nvmVNETEgressDigManipChIDListNAME = ;
DESC = The value of this object selects voice channels \
associated with the phone number. The valid \
string consists of the substring 'B1'~'B6', \
'C1'~'C12', 'D1'~'D12', and 'E1'~'E2'. \
(Configuration);
HELP = Valid characters are decimal digits, 'B', 'C', \
'D', and 'E'.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.1.10.1.4 |
vnet-control OBJECT IDENTIFIER .micom-oscar.21.2 |
mcmVNETChControlTableNAME = ;
DESC = The VNET Voice Channel Control table. \
HELP = ;
CAPABILITIES = NET_OPER, VPN_OPER ; SEQUENCE OF McmVNETChControlEntry .micom-oscar.21.2.1 |
mcmVNETChControlEntryNAME = ;
DESC = An entry in the VNET Voice Channel Control \
table.;
HELP = ;
CAPABILITIES = ; McmVNETChControlEntry .micom-oscar.21.2.1.1 |
mcmVNETChControlLimIDNAME = ;
DESC = The card lim (logical interface module) number of a \
particular voice channel. Used as an index to the \
VNET Voice Channel Control table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.2.1.1.1 |
mcmVNETChControlChannelIDNAME = ;
DESC = The position of the voice channel in the lim. \
Used as an index to the VNET Voice \
Channel Control table.;
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.2.1.1.2 |
mcmVNETChControlActionCmdNAME = ;
DESC = Setting this object will perform various \
actions on the specified voice channel. \
Note: Starting with software release 3.0, \
the enumeration clearChannelCounters (2) is \
not supported. The enumeration is included \
here only to support backwards compatibility \
for software versions prior to release 3.0.;
HELP = 1: perform hardware reset to DSP. \
2: clear statistics counter. \
3: download code to DSP. \
4: disconnect call. \
5: set DSP to loopback mode. \
6: terminate test. \
7: force connect channel by using the \
auto call number. NOTE: This option is not \
supported by the ISDN BRI voice card.;
CAPABILITIES = ;rw Enumeration .micom-oscar.21.2.1.1.3 |
mcmVNETSysControlActionCmdNAME = ;
DESC = Setting this object will perform various \
actions on the VNET voice system. \
Note: Starting with software release 3.0, \
the enumerations clearNetworkCounters (1) and \
clearChannelCounters (3) are not supported. \
The enumeration is included here only to support \
backwards compatibility for software versions \
prior to release 3.0.;
HELP = 1: clear network statistics counters. \
2: perform hardware reset to all channels. \
3: clear all channel statistics counters. \
4: download code to all channels. \
5: disconnect all channel's calls. \
6: set all channels to loopback mode. \
7: terminate all channel's tests. \
8: force connect all channels by using the
auto call numbers. NOTE: This option is not \
supported by the ISDN BRI voice card.; \
9: re-register phone number.;
CAPABILITIES = NET_OPER, VPN_OPER ;rw Enumeration .micom-oscar.21.2.2 |
vnet-status OBJECT IDENTIFIER .micom-oscar.21.3 |
mcmVNETChStatusTableNAME = ;
DESC = The VNET Voice Channel Status Display table. \
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF McmVNETChStatusEntry .micom-oscar.21.3.1 |
mcmVNETChStatusEntryNAME = ;
DESC = An entry in the VNET Voice Channel Status Display \
table.;
HELP = ;
CAPABILITIES = ; McmVNETChStatusEntry .micom-oscar.21.3.1.1 |
mcmVNETChStatusLimIDNAME = ;
DESC = The card lim (logical interface module) number of \
a particular voice channel. Used as an index to \
the VNET Voice Channel Status Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.1 |
mcmVNETChStatusChannelIDNAME = ;
DESC = The position of the voice channel in the lim. \
Used as an index to the VNET Voice \
Channel Status Display table.;
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.3.1.1.2 |
mcmVNETChStatusInterfaceTypeNAME = ;
DESC = The value of this object indicates the interface \
type of the specified voice channel.;
HELP = Upon powerup, the interface type will not be \
available until the DSP software is loaded and its \
status is reported.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.3 |
mcmVNETChStatusInterfaceSwIDNAME = ;
DESC = The value of this object indicates the command \
interface version ID (CIVID) of the specified voice \
channel. (Note: CIVID is 20 or above.);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.3.1.1.4 |
mcmVNETChStatusEMTypeNAME = ;
DESC = The value of this object indicates the E&M \
type of the specified voice channel.;
HELP = This is for E&M interface channels only. Other \
interface types will show notApplicable.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.5 |
mcmVNETChStatusModelIDNAME = ;
DESC = The value of this object indicates the hardware \
module type for the specified DVM voice channel.;
HELP = This is for DVM voice channels only. Analog \
voice channels will show notApplicable.;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.6 |
mcmVNETChStatusDSPOperationNAME = ;
DESC = The value of this object indicates the current \
DSP status of the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.7 |
mcmVNETChStatusNetworkConnectNAME = ;
DESC = The value of this object indicates the current \
channel network connect status of the specified \
voice channel.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.8 |
mcmVNETChStatusRemoteChHwTypeNAME = ;
DESC = The value of this object indicates the remote \
voice channel hardware type (corresponding to \
the specified voice channel).;
HELP = This will be the NULL string if the specified \
voice channel is not connected.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.9 |
mcmVNETChStatusRemoteChNodeNameNAME = ;
DESC = The value of this object indicates the remote \
voice channel node name (corresponding to \
the specified voice channel).;
HELP = This will be the NULL string if the specified \
voice channel is not connected.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.10 |
mcmVNETChStatusRemoteChNumNAME = ;
DESC = The value of this object indicates the remote \
voice channel number (corresponding to \
the specified voice channel).;
HELP = This will be the NULL string if the specified \
voice channel is not connected.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.11 |
mcmVNETChStatusRemoteChIfTypeNAME = ;
DESC = The value of this object indicates the remote \
voice channel interface type (corresponding to \
the specified voice channel).;
HELP = This will be the NULL string if the specified \
voice channel is not connected.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.12 |
mcmVNETChStatusRemoteFrameIfVerNAME = ;
DESC = The value of this object indicates the final \
negotiated software version to be run on both \
sides of a voice channel connection.;
HELP = This will be 0 if the specified \
voice channel is not connected.;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.3.1.1.13 |
mcmVNETChStatusRemoteChVoiceAlgNAME = ;
DESC = The value of this object indicates the final \
negotiated voice algorithm running on both \
sides of a voice channel connection.;
HELP = This will be the NULL string if the specified \
voice channel is not connected.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.14 |
mcmVNETChStatusRemoteChFaxAlgNAME = ;
DESC = The value of this object indicates the final \
negotiated voice fax algorithm and maximum \
speed running on both sides of a voice fax \
channel connection.;
HELP = This will be the NULL string if the specified \
voice fax channel is not connected.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.15 |
mcmVNETChStatusRemoteChModemAlgNAME = ;
DESC = The value of this object indicates the final \
negotiated voice modem algorithm and maximum \
speed running on both sides of a voice modem \
channel connection.;
HELP = This will be the NULL string if the specified \
voice fax channel is not connected.;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.16 |
mcmVNETChStatusSelfTestResultNAME = ;
DESC = The value of this object indicates the results \
of a self test performed on the specified voice \
channel.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.17 |
mcmVNETChStatusFlashEPROMNAME = ;
DESC = The value of this object indicates the current \
flash EPROM status in the DSP of the specified \
voice channel.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.18 |
mcmVNETChStatusEPROMNAME = ;
DESC = The value of this object indicates the current \
EPROM status in the DSP of the specified voice \
channel.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.19 |
mcmVNETChStatusDspPROMVerNAME = ;
DESC = The value of this object indicates the DSP PROM \
version of the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.20 |
mcmVNETChStatusPROMIDNAME = ;
DESC = The value of this object indicates the PROM \
ID of the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro DisplayString .micom-oscar.21.3.1.1.21 |
mcmVNETChStatusInputLevelNAME = ;
DESC = The value of this object indicates the input \
level of the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.3.1.1.22 |
voiceSysStatusGroup OBJECT IDENTIFIER .micom-oscar.21.3.2 |
voiceSysStatusPhoneRegistrationStatusNAME = PhoneRegistrationStatus;
DESC = Indicates current communications \
status with NAS;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG;ro Enumeration .micom-oscar.21.3.2.1 |
vnet-statistics OBJECT IDENTIFIER .micom-oscar.21.4 |
mcmVNETChStatsTableNAME = ;
DESC = The VNET Voice Channel Statistics Display table. \
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF McmVNETChStatsEntry .micom-oscar.21.4.1 |
mcmVNETChStatsEntryNAME = ;
DESC = An entry in the VNET Voice Channel Statistics \
Display table.;
HELP = ;
CAPABILITIES = ; McmVNETChStatsEntry .micom-oscar.21.4.1.1 |
mcmVNETChStatsLimIDNAME = ;
DESC = The card lim (logical interface module) number of a \
particular voice channel. Used as an index to the \
VNET Voice Channel Statistics Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.21.4.1.1.1 |
mcmVNETChStatsChannelIDNAME = ;
DESC = The position of the voice channel in the lim. \
Used as an index to the VNET Voice \
Channel Statistics Display table.;
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.21.4.1.1.2 |
mcmVNETChStatsOutCallConnTimeNAME = ;
DESC = The value of this object indicates the total \
connection time (in sec) since the last statistics \
reset for the specified voice channel outgoing \
calls. (Excludes call setup time and local calls.) ;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.3 |
mcmVNETChStatsInCallConnTimeNAME = ;
DESC = The value of this object indicates the total \
connection time (in sec) since the last statistics \
reset for the specified voice channel incoming \
calls. (Excludes local calls.) ;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.4 |
mcmVNETChStatsOutCallsSuccededNAME = ;
DESC = The value of this object indicates the total \
number of positive call responses sent from the \
remote DSP since the last statistics reset \
for the specified voice channel. (Excludes \
local calls.) ;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.5 |
mcmVNETChStatsOutCallsFailedNAME = ;
DESC = The value of this object indicates the total \
number of negative call responses sent from the \
remote DSP since the last statistics reset \
for the specified voice channel. (Excludes \
local calls.) ;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.6 |
mcmVNETChStatsInCallsAcceptedNAME = ;
DESC = The value of this object indicates the total \
number of positive call responses sent to the \
remote DSP since the last statistics reset \
for the specified voice channel. (Excludes \
local calls.) ;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.7 |
mcmVNETChStatsInCallsRejectedNAME = ;
DESC = The value of this object indicates the total \
number of negative call responses sent to the \
remote DSP since the last statistics reset \
for the specified voice channel. (Excludes \
local calls.) ;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.8 |
mcmVNETChStatsNumberOfResetsNAME = ;
DESC = The value of this object indicates the total \
number of resets sent to the DSP corresponding \
to the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.9 |
mcmVNETChStatsNumberOfRetriesNAME = ;
DESC = The value of this object indicates the total \
number of no responses sent from the DSP \
since the last DSP reset corresponding \
to the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.10 |
mcmVNETChStatsBBCFramesRcvdNAME = ;
DESC = The value of this object indicates the total \
number of frames with Bad Byte Count received \
from the DSP corresponding to the specified \
voice channel.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.11 |
mcmVNETChStatsBEOFFramesRcvdNAME = ;
DESC = The value of this object indicates the total \
number of frames with Bad End Of Frame \
character received from the DSP corresponding \
to the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.12 |
mcmVNETChStatsLostSpeechFramesNAME = ;
DESC = The value of this object indicates the total \
number of speech frames sent by the remote \
that were lost since power up corresponding \
to the specified voice channel.;
HELP = Always 0 if sequence number in speech frame \
is not used.;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.13 |
mcmVNETChStatsLostControlFramesNAME = ;
DESC = The value of this object indicates the total \
number of control frames sent by the remote \
that were lost corresponding to the specified \
voice channel.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.14 |
mcmVNETChStatsInvalPayloadFrRcvdNAME = ;
DESC = The value of this object indicates the total \
number of payload frames received from the \
remote with bad length or frame type \
corresponding to the specified voice channel.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.15 |
mcmVNETChStatsInvalPUMPMsgRcvdNAME = ;
DESC = The value of this object indicates the total \
number of PUMP messages received from the \
remote with unknown message type, IEs, or \
invalid length corresponding to the specified \
voice channel.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.21.4.1.1.16 |
mcmVNETNetStatsGroup OBJECT IDENTIFIER .micom-oscar.21.4.2 |
mcmVNETNetStatsSucceedOutSVCCallsNAME = ;
DESC = The value of this object indicates the total \
number of successful SVC calls since the \
last network statistics reset.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.1 |
mcmVNETNetStatsFailedOutSVCCallsNAME = ;
DESC = The value of this object indicates the total \
number of unsuccessful SVC calls since the \
last network statistics reset.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.2 |
mcmVNETNetStatsAcceptedInCallsNAME = ;
DESC = The value of this object indicates the total \
number of SVC calls accepted by this access device \
since the last network statistics reset.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.3 |
mcmVNETNetStatsRejectedInCallsNAME = ;
DESC = The value of this object indicates the total \
number of SVC calls rejected by this access device \
since the last network statistics reset.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.4 |
mcmVNETNetStatsSucceedDNARequestsNAME = ;
DESC = The value of this object indicates the total \
number of successful DNA requests received \
by this access device since the last network \
statistics reset.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.5 |
mcmVNETNetStatsFailedDNARequestsNAME = ;
DESC = The value of this object indicates the total \
number of unsuccessful DNA requests received \
by this access device since the last network \
statistics reset.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.6 |
mcmVNETNetStatsFailedBuffAllocationsNAME = ;
DESC = The value of this object indicates the total \
number of streams buffers not available \
to this access device.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.7 |
mcmVNETNetStatsNumActiveCallsNAME = ;
DESC = The value of this object indicates the total \
number of calls in progress or connected \
in this access device.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.21.4.2.8 |