MICOM-4400-T1E1-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for MICOM-4400-T1E1-MIB.
162
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
162 total| Object Name |
|---|
micom-2t1e1 OBJECT IDENTIFIER .micom-oscar.22 |
RFC1155-SMI Unknown .micom-oscar.22 |
mcm4400T1NoCodeImageNAME = ;
DESC = Indicates that the built image doesn't \
contain T1 code.\
Severity Level: MAJOR.;
HELP = The Image loaded does not contain T1 code.\
Load a new Image that includes T1 code, or \
consult with the System Admin. or Field \
Personnel.; TRAP-TYPE .micom-oscar.22.0.1 |
mcm4400T1DownloadFailNAME = ;
DESC = Indicates a failure occurred during the T1 \
code download.\
Severity Level: MAJOR;
HELP = Retry the download. Re-boot the access device and \
check if it downloads correctly. Also, verify \
the T1 code that is build with access device image \
is the right version. If problem persist, consult \
your system admin., or field personnel.; TRAP-TYPE .micom-oscar.22.0.2 |
mcm4400T1OutOfOrderNAME = ;
DESC = Indicates the T1 is not responding.\
Severity Level: CRITICAL.;
HELP = Management frame is out of order. Check for \
Framing error. If it does not recover, Please \
contact your Sys Admin. or Field personnel.; TRAP-TYPE .micom-oscar.22.0.3 |
mcm4400T1OutOfOrderRecoveredNAME = ;
DESC = Indicates recovery from the T1 out of order condition.\
Severity Level: INFORMATIVE.;
HELP = T1 is responding. Normal Status Indicator.; TRAP-TYPE .micom-oscar.22.0.4 |
mcm4400T1FailToSyncUpNAME = ;
DESC = Indicates the T1 is unable to sync up.\
Severity Level : CRITICAL.;
HELP = Check the physical connection locally, and \
to the remote device. Possible protocol error. \
If problem still persist, contact your \
system admin., or field personnel.; TRAP-TYPE .micom-oscar.22.0.5 |
mcm4400T1FailToSyncUpRecoveredNAME = ;
DESC = Indicates recovery from the T1 failure \
to sync up condition.\
Severity Level: INFORMATIVE.;
HELP = T1 has recovered. Normal Status Indicator.; TRAP-TYPE .micom-oscar.22.0.6 |
mcm4400T1AISAlarmSetNAME = ;
DESC = Indicates a T1 AIS Alarm condition is present.\
Severity Level: CRITICAL.;
HELP = Check physical link of the local T1, and the Remote \
PBX. Possible Framing error. If problem is not \
resolved, contact sys admin., or field personnel.; TRAP-TYPE .micom-oscar.22.0.7 |
mcm4400T1AISAlarmClearNAME = ;
DESC = Indicates a T1 AIS Alarm condition has cleared.\
Severity Level: INFORMATIVE.;
HELP = T1 AIS Alarm is cleared. Normal Status Indicator.; TRAP-TYPE .micom-oscar.22.0.8 |
mcm4400T1RedAlarmSetNAME = ;
DESC = Indicates a T1 Red Alarm condition is present.\
Severity Level: CRITICAL.;
HELP = Check the Physical Connection to remote. \
If the Alarm condition is still persistant, \
contact your Field Personnel.; TRAP-TYPE .micom-oscar.22.0.9 |
mcm4400T1RedAlarmClearNAME = ;
DESC = Indicates a T1 Red Alarm condition has cleared.\
Severity Level: IMFORMATIVE. ;
HELP = Red Alarm Cleared. Normal Status Indicator!.; TRAP-TYPE .micom-oscar.22.0.10 |
mcm4400T1YellowAlarmSetNAME = ;
DESC = Indicates a T1 Yellow Alarm condition is present.\
Severity Level: MINOR.;
HELP = TX or RX side for physical connection may be faulty; \
Possible Framing error with Remote device. Run Loopback \
test if possible, & determine the problem. If that does not\
help, please contact Field Personnel or System admin.; TRAP-TYPE .micom-oscar.22.0.11 |
mcm4400T1YellowAlarmClearNAME = ;
DESC = Indicates a T1 Yellow Alarm condition has cleared.\
Severity Level: INFORMATIVE.;
HELP = Yellow Alarm is cleared. Normal Status Indicator!.; TRAP-TYPE .micom-oscar.22.0.12 |
mcm4400E1NoCodeImageNAME = ;
DESC = Indicates that the built image doesn't \
contain E1 code.\
Severity Level: MAJOR.;
HELP = The Image loaded does not contain E1 code.\
Load a new Image that includes E1 code, or \
consult with the System Admin. or Field \
Personnel.; TRAP-TYPE .micom-oscar.22.0.13 |
mcm4400E1DownloadFailNAME = ;
DESC = Indicates a failure occurred during the E1 \
code download.\
Severity Level: MAJOR. ;
HELP = Retry the download. Re-boot the access device and \
check if it downloads correctly. Also, verify \
the E1 code that is built with access device \
image is the right version. If problem persist, \
consult your system admin., or field personnel.; TRAP-TYPE .micom-oscar.22.0.14 |
mcm4400E1OutOfOrderNAME = ;
DESC = Indicates the E1 is not responding.\
Severity Level: CRITICAL.;
HELP = Management frame is out of order. Check for \
Framing error. If it does not recover, Please \
contact your Sys Admin. or Field personnel.; TRAP-TYPE .micom-oscar.22.0.15 |
mcm4400E1OutOfOrderRecoveredNAME = ;
DESC = Indicates recovery from the E1 out of order condition.\
Severity Level: INFORMATIVE.;
HELP = E1 is responding. Normal Status Indicator.; TRAP-TYPE .micom-oscar.22.0.16 |
mcm4400E1FailToSyncUpNAME = ;
DESC = Indicates the E1 is unable to sync up.\
Severity Level: CRITICAL.;
HELP = Check the physical connection locally, and \
to the remote device. Possible protocol error. \
If problem still persist, contact your \
system admin., or field personnel.; TRAP-TYPE .micom-oscar.22.0.17 |
mcm4400E1FailToSyncUpRecoveredNAME = ;
DESC = Indicates recovery from the E1 failure \
to sync up condition.\
Severity Level: INFORMATIVE.;
HELP = E1 has recovered. Normal Status Indicator.; TRAP-TYPE .micom-oscar.22.0.18 |
mcm4400E1AISAlarmSetNAME = ;
DESC = Indicates an E1 AIS Alarm condition is present.\
Severity Level: MAJOR.;
HELP = Check physical link of the local E1, and the Remote \
PBX. Possible Framing error. If problem is not \
resolved, contact sys admin., or field personnel.; TRAP-TYPE .micom-oscar.22.0.19 |
mcm4400E1AISAlarmClearNAME = ;
DESC = Indicates an E1 AIS Alarm condition has cleared.\
Severity Level: INFORMATIVE. ;
HELP = E1 AIS Alarm is cleared. Normal Status Indicator.; TRAP-TYPE .micom-oscar.22.0.20 |
mcm4400E1RedAlarmSetNAME = ;
DESC = Indicates an E1 Red Alarm condition is present.\
Severity Level: MAJOR.;
HELP = Check the Physical Connection to remote. \
Run a loopback test and determine the problem. \
If the Alarm condition is still persistant, \
contact your Field Personnel.; TRAP-TYPE .micom-oscar.22.0.21 |
mcm4400E1RedAlarmClearNAME = ;
DESC = Indicates an E1 Red Alarm condition has cleared.\
Severity Level: INFORMATIVE.;
HELP = Red Alarm Cleared. Normal Status Indicator!.; TRAP-TYPE .micom-oscar.22.0.22 |
mcm4400E1TS16AISAlarmSetNAME = ;
DESC = Indicates an E1 TS16 AIS Alarm is present.\
Severity Level: MAJOR.;
HELP = TX or RX side for physical connection may be faulty; \
Possible Framing error with Remote device. Run Loopback \
test if possible, & determine the problem. If that does not\
help, please contact Field Personnel or System admin.; TRAP-TYPE .micom-oscar.22.0.23 |
mcm4400E1TS16AISAlarmClearNAME = ;
DESC = Indicates an E1 TS16 AIS Alarm has cleared.\
Severity Level: INFORMATIVE.;
HELP = Alarm is cleared. Normal Status Indicator!.; TRAP-TYPE .micom-oscar.22.0.24 |
mcm4400E1OOSMFAlarmSetNAME = ;
DESC = Indicates an E1 00SMF Alarm is present.\
Severity Level: MAJOR.;
HELP = Framing error due to signal loss. Run Loopback \
test and determine the problem. For further help \
contact your Field Personnel.; TRAP-TYPE .micom-oscar.22.0.25 |
mcm4400E1OOSMFAlarmClearNAME = ;
DESC = Indicates an E1 00SMF Alarm has cleared.\
Severity Level: INFORMATIVE.;
HELP = OOSMF Alarm is cleared. Normal Status Indicator!.; TRAP-TYPE .micom-oscar.22.0.26 |
mcm4400E1RemoteYBitAlarmSetNAME = ;
DESC = Indicates an E1 Remote Y Bit Alarm is present.\
Severity Level: MAJOR.;
HELP = Run Loopback test, and determine the condition. \
For further help, contact Field Personnel.; TRAP-TYPE .micom-oscar.22.0.27 |
mcm4400E1RemoteYBitAlarmClearNAME = ;
DESC = Indicates an E1 Remote Y Bit Alarm has cleared.\
Severity Level: INFORMATIVE.;
HELP = Remote YBit Alarm is cleared. Normal Status \
Indicator.; TRAP-TYPE .micom-oscar.22.0.28 |
mcm4400E1RemoteABitAlarmSetNAME = ;
DESC = Indicates an E1 Remote A Bit Alarm is present.\
Severity Level: MAJOR.;
HELP = Possible frame Error. Please run loopback test \
and determine the condition. If Alarm \
is not cleared, contact your Field Personnel.; TRAP-TYPE .micom-oscar.22.0.29 |
mcm4400E1RemoteABitAlarmClearNAME = ;
DESC = Indicates an E1 Remote Y Bit Alarm has cleared.\
Severity Level: INFORMATIVE.;
HELP = Alarm is cleared. Normal Status Indicator!.; TRAP-TYPE .micom-oscar.22.0.30 |
mcm4400E1OOCMFAlarmSetNAME = ;
DESC = Indicates an E1 00CMF Alarm is present.\
Severity Level: MAJOR.;
HELP = CRC multframe alignment is lost. Run loobback \
test and determine the problem. For further \
help, contact Field Personnel. ; TRAP-TYPE .micom-oscar.22.0.31 |
mcm4400E1OOCMFAlarmClearNAME = ;
DESC = Indicates an E1 00CMF Alarm has cleared.\
Severity Level: INFORMATIVE.;
HELP = OOCMF Alarm is cleared. Normal Status Indicator.; TRAP-TYPE .micom-oscar.22.0.32 |
t1e1-r2-configuration OBJECT IDENTIFIER .micom-oscar.22.1 |
mcm4400t1e1LineCfgTableNAME = ;
DESC = The T1/E1 Line Configuration table. \
(Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1LineCfgEntry .micom-oscar.22.1.1 |
mcm4400t1e1LineCfgEntryNAME = ;
DESC = An entry in the T1/E1 Line Configuration \
table. (Operational);
HELP = ;
CAPABILITIES = ; Mcm4400t1e1LineCfgEntry .micom-oscar.22.1.1.1 |
mcm4400t1e1LineCfgLineIDNAME = ;
DESC = The T1/E1 line identification specifies which line \
is to be configured. Used as the index to the \
T1/E1 Line Configuration table. (Operational);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.1.1.1 |
mcm4400t1e1LineCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
to be used to configure the specified T1/E1 \
line. (Operational);
HELP = 1: expected as default profile for local line. \
2: expected as default profile for network line.;
CAPABILITIES = ;rw INTEGER .micom-oscar.22.1.1.1.2 |
mcm4400t1e1ProfCfgTableNAME = ;
DESC = The T1/E1 Profile Configuration table. \
(Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1ProfCfgEntry .micom-oscar.22.1.2 |
mcm4400t1e1ProfCfgEntryNAME = ;
DESC = An entry in the T1/E1 Profile Configuration \
table. (Operational);
HELP = ;
CAPABILITIES = ; Mcm4400t1e1ProfCfgEntry .micom-oscar.22.1.2.1 |
mcm4400t1e1ProfCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
number. Used as an index to the T1/E1 \
Profile Configuration table. (Operational);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.1.2.1.1 |
mcm4400t1e1ProfCfgT1FrameFmtNAME = ;
DESC = The value of this object specifies the T1 \
frame format used in the line. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.2.1.2 |
mcm4400t1e1ProfCfgT1LineCodeNAME = ;
DESC = The value of this object specifies the T1 \
coding format used in the line. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.2.1.3 |
mcm4400t1e1ProfCfgE1LineCodeNAME = ;
DESC = The value of this object specifies the E1 \
coding format used in the line. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.2.1.4 |
mcm4400t1e1ProfCfgIdleCodeNAME = ;
DESC = The value of this object specifies the code \
to be filled in the line when idle. (Operational);
HELP = ;
CAPABILITIES = ;rw INTEGER (0..'ff'h) .micom-oscar.22.1.2.1.5 |
mcm4400t1e1ProfCfgT1LineBuildOutNAME = ;
DESC = The value of this object specifies the cable \
length attached to a local T1 line. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.2.1.6 |
mcm4400t1e1ProfCfgT1LoopbackNAME = ;
DESC = The value of this object specifies whether \
to enable or disable the T1 line loopback \
to be invoked. (Operational);
HELP = 1: expected as default for a local T1 line profile. \
2: expected as default for a network T1 line profile.;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.2.1.7 |
mcm4400t1e1ProfCfgE1CRC4NAME = ;
DESC = The value of this object specifies whether \
to enable or disable a T1 line CRC4. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.2.1.8 |
mcm4400t1e1ProfCfgE1TS16ConnNAME = ;
DESC = The value of this object specifies where the \
TS16 goes (for a T1 line). (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.2.1.9 |
mcm4400t1e1DS0ChConnTableNAME = ;
DESC = The T1/E1 DS0 Channel Connection \
Configuration table.(Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1DS0ChConnEntry .micom-oscar.22.1.3 |
mcm4400t1e1DS0ChConnEntryNAME = ;
DESC = An entry in the T1/E1 DS0 Channel \
Connection Configuration table. (Operational);
HELP = ;
CAPABILITIES = ; Mcm4400t1e1DS0ChConnEntry .micom-oscar.22.1.3.1 |
mcm4400t1e1DS0ChConnLineIDNAME = ;
DESC = The T1/E1 line identification specifies which line \
is to be configured. Used as an index to the \
T1/E1 DS0 Channel Connection Configuration \
table. (Operational);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.3.1.1 |
mcm4400t1e1DS0ChConnDS0IndexNAME = ;
DESC = The T1/E1 DS0 index specifies which time slot \
is to be connected. Used as an index to the \
T1/E1 DS0 Channel Connection Configuration \
table. (Operational);
HELP = For T1, 24 is the maximum. An error will be \
returned for a T1 DS0 index greater than 24.;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.1.3.1.2 |
mcm4400t1e1DS0ChConnStateNAME = ;
DESC = The value of this object specifies where the \
T1/E1 line channel slot (DS0) is to be connected \
to. (Operational);
HELP = Note 1: if 2-37 is selected, the previous setting \
must be idle, or an error will be returned. \
Note 2: if idle is specified and the previous setting \
was bypass (voice or data), the corresponding DS0 \
in the other line will also be set to idle automatically. \
Note 3: if bypass (voice or data) is specified, the \
corresponding DS0 in the other line will also be \
set to the same bypass mode automatically.;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.3.1.3 |
mcm4400t1e1DPCfgTableNAME = ;
DESC = The T1/E1 Data Port Configuration table. \
(Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1DPCfgEntry .micom-oscar.22.1.4 |
mcm4400t1e1DPCfgEntryNAME = ;
DESC = An entry in the T1/E1 Data Port \
Configuration table. (Operational);
HELP = ;
CAPABILITIES = ; Mcm4400t1e1DPCfgEntry .micom-oscar.22.1.4.1 |
mcm4400t1e1DPCfgPortNumNAME = ;
DESC = The T1/E1 port number specifies which data port \
is to be configured. Used as an index to the \
T1/E1 Data Port Configuration table. (Operational);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.4.1.1 |
mcm4400t1e1DPCfgDataRateNAME = ;
DESC = The value of this object selects the baud rate \
for the specified data port. (Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.4.1.2 |
mcm4400t1e1DPCfgClockNAME = ;
DESC = The value of this object selects the clock \
source for the specified data port. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.4.1.3 |
mcm4400t1e1DPCfgDTRCntlNAME = ;
DESC = The value of this object selects the DTR \
control for the specified data port. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.4.1.4 |
mcm4400t1e1DPCfgRTSCntlNAME = ;
DESC = The value of this object selects the RTS \
control for the specified data port. \
(Operational);
HELP = ;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.1.4.1.5 |
mcm4400t1e1SysCfgClockSourceNAME = ;
DESC = The value of this object specifies where the \
system clock comes from. (Operational);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG;rw Enumeration .micom-oscar.22.1.5 |
nvm4400t1e1LineCfgTableNAME = ;
DESC = The T1/E1 Line Configuration table. \
(Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Nvm4400t1e1LineCfgEntry .micom-oscar.22.1.6 |
nvm4400t1e1LineCfgEntryNAME = ;
DESC = An entry in the T1/E1 Line Configuration \
table. (Configuration);
HELP = ;
CAPABILITIES = ; Nvm4400t1e1LineCfgEntry .micom-oscar.22.1.6.1 |
nvm4400t1e1LineCfgLineIDNAME = ;
DESC = The T1/E1 line identification specifies which line \
is to be configured. Used as the index to the \
T1/E1 Line Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.6.1.1 |
nvm4400t1e1LineCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
to be used to configure the specified T1/E1 \
line. (Configuration);
HELP = 1: expected as default profile for local line. \
2: expected as default profile for network line.;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.1.6.1.2 |
nvm4400t1e1ProfCfgTableNAME = ;
DESC = The T1/E1 Profile Configuration table. \
(Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Nvm4400t1e1ProfCfgEntry .micom-oscar.22.1.7 |
nvm4400t1e1ProfCfgEntryNAME = ;
DESC = An entry in the T1/E1 Profile Configuration \
table. (Configuration);
HELP = ;
CAPABILITIES = ; Nvm4400t1e1ProfCfgEntry .micom-oscar.22.1.7.1 |
nvm4400t1e1ProfCfgProfileNumNAME = ;
DESC = The value of this object indicates the profile \
number. Used as an index to the T1/E1 \
Profile Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.1.7.1.1 |
nvm4400t1e1ProfCfgT1FrameFmtNAME = ;
DESC = The value of this object specifies the T1 \
frame format used in the line. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.7.1.2 |
nvm4400t1e1ProfCfgT1LineCodeNAME = ;
DESC = The value of this object specifies the T1 \
coding format used in the line. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.7.1.3 |
nvm4400t1e1ProfCfgE1LineCodeNAME = ;
DESC = The value of this object specifies the E1 \
coding format used in the line. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.7.1.4 |
nvm4400t1e1ProfCfgIdleCodeNAME = ;
DESC = The value of this object specifies the code \
to be filled in the line when idle. (Configuration);
HELP = ;
CAPABILITIES = ;ro INTEGER (0..'ff'h) .micom-oscar.22.1.7.1.5 |
nvm4400t1e1ProfCfgT1LineBuildOutNAME = ;
DESC = The value of this object specifies the cable \
length attached to a local T1 line. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.7.1.6 |
nvm4400t1e1ProfCfgT1LoopbackNAME = ;
DESC = The value of this object specifies whether \
to enable or disable the T1 line loopback \
to be invoked. (Configuration);
HELP = 1: expected as default for a local T1 line profile. \
2: expected as default for a network T1 line profile.;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.7.1.7 |
nvm4400t1e1ProfCfgE1CRC4NAME = ;
DESC = The value of this object specifies whether \
to enable or disable a T1 line CRC4. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.7.1.8 |
nvm4400t1e1ProfCfgE1TS16ConnNAME = ;
DESC = The value of this object specifies where the \
TS16 goes (for a T1 line). (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.7.1.9 |
nvm4400t1e1DS0ChConnTableNAME = ;
DESC = The T1/E1 DS0 Channel Connection \
Configuration table.(Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Nvm4400t1e1DS0ChConnEntry .micom-oscar.22.1.8 |
nvm4400t1e1DS0ChConnEntryNAME = ;
DESC = An entry in the T1/E1 DS0 Channel \
Connection Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ; Nvm4400t1e1DS0ChConnEntry .micom-oscar.22.1.8.1 |
nvm4400t1e1DS0ChConnLineIDNAME = ;
DESC = The T1/E1 line identification specifies which line \
is to be configured. Used as an index to the \
T1/E1 DS0 Channel Connection Configuration \
table. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.8.1.1 |
nvm4400t1e1DS0ChConnDS0IndexNAME = ;
DESC = The T1/E1 DS0 index specifies which time slot \
is to be connected. Used as an index to the \
T1/E1 DS0 Channel Connection Configuration \
table. (Configuration);
HELP = For T1, 24 is the maximum. An error will be \
returned for a T1 DS0 index greater than 24.;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.1.8.1.2 |
nvm4400t1e1DS0ChConnStateNAME = ;
DESC = The value of this object specifies where the \
T1/E1 line channel slot (DS0) is to be connected \
to. (Configuration);
HELP = Note 1: if 2-37 is selected, the previous setting \
must be idle, or an error will be returned. \
Note 2: if idle is specified and the previous setting \
was bypass (voice or data), the corresponding DS0 \
in the other line will also be set to idle automatically. \
Note 3: if bypass (voice or data) is specified, the \
corresponding DS0 in the other line will also be \
set to the same bypass mode automatically.;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.8.1.3 |
nvm4400t1e1DPCfgTableNAME = ;
DESC = The T1/E1 Data Port Configuration table. \
(Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Nvm4400t1e1DPCfgEntry .micom-oscar.22.1.9 |
nvm4400t1e1DPCfgEntryNAME = ;
DESC = An entry in the T1/E1 Data Port \
Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ; Nvm4400t1e1DPCfgEntry .micom-oscar.22.1.9.1 |
nvm4400t1e1DPCfgPortNumNAME = ;
DESC = The T1/E1 port number specifies which data port \
is to be configured. Used as an index to the \
T1/E1 Data Port Configuration table. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.9.1.1 |
nvm4400t1e1DPCfgDataRateNAME = ;
DESC = The value of this object selects the baud rate \
for the specified data port. (Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.9.1.2 |
nvm4400t1e1DPCfgClockNAME = ;
DESC = The value of this object selects the clock \
source for the specified data port. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.9.1.3 |
nvm4400t1e1DPCfgDTRCntlNAME = ;
DESC = The value of this object selects the DTR \
control for the specified data port. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.9.1.4 |
nvm4400t1e1DPCfgRTSCntlNAME = ;
DESC = The value of this object selects the RTS \
control for the specified data port. \
(Configuration);
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.1.9.1.5 |
nvm4400t1e1SysCfgClockSourceNAME = ;
DESC = The value of this object specifies where the \
system clock comes from. (Configuration);
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG;ro Enumeration .micom-oscar.22.1.10 |
t1e1-r2-control OBJECT IDENTIFIER .micom-oscar.22.2 |
mcm4400t1e1DS0ChTestCmdTableNAME = ;
DESC = The T1/E1 DS0 Channel Test Command \
table. \
HELP = ;
CAPABILITIES = NET_OPER, VPN_OPER ; SEQUENCE OF Mcm4400t1e1DS0ChTestCmdEntry .micom-oscar.22.2.1 |
mcm4400t1e1DS0ChTestCmdEntryNAME = ;
DESC = An entry in the T1/E1 DS0 Channel \
Test Command table.;
HELP = ;
CAPABILITIES = ; Mcm4400t1e1DS0ChTestCmdEntry .micom-oscar.22.2.1.1 |
mcm4400t1e1DS0ChTestCmdLineIDNAME = ;
DESC = The T1/E1 line ID specifies which line is to \
be tested. Used as an index to the \
T1/E1 DS0 Channel Test Command table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.2.1.1.1 |
mcm4400t1e1DS0ChTestCmdDS0IndexNAME = ;
DESC = The DS0 Index specifies which time slot is \
to be tested. Used as an index to the \
T1/E1 DS0 Channel Test Command table.;
HELP = For T1, 24 is the maximum. An error will be \
returned if a value greater than 24 is selected.;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.2.1.1.2 |
mcm4400t1e1DS0ChTestCmdTstPatternNAME = ;
DESC = Setting this object will initiate various \
test pattern testing on the specified T1/E1 \
DS0 channel.;
HELP = For QRSS, TP511, and Fixed, the T1/E1 \
access module will generate and verify the \
selected test pattern. \
For Loop test, it simply loops the input \
data back to the same DS0 channel. \
In T1, if 4 is specified, an error will be \
returned.;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.2.1.1.3 |
mcm4400t1e1LineTestCmdTableNAME = ;
DESC = The T1/E1 Line Test Command \
table. \
HELP = ;
CAPABILITIES = NET_OPER, VPN_OPER ; SEQUENCE OF Mcm4400t1e1LineTestCmdEntry .micom-oscar.22.2.2 |
mcm4400t1e1LineTestCmdEntryNAME = ;
DESC = An entry in the T1/E1 Line Test \
Command table.;
HELP = ;
CAPABILITIES = ; Mcm4400t1e1LineTestCmdEntry .micom-oscar.22.2.2.1 |
mcm4400t1e1LineTestCmdLineIDNAME = ;
DESC = The T1/E1 line ID specifies which line is to \
be tested. Used as the index to the \
T1/E1 Line Test Command table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.2.2.1.1 |
mcm4400t1e1LineTestCmdTstPatternNAME = ;
DESC = Setting this object will initiate various \
tests on the specified T1/E1 line.;
HELP = Line Loopback: receiver or transmitter is \
connected to transmitter or receiver; respectively. \
Digital Loopback: data is stripped off the \
DS0 channel and reinserted in the same channel. \
External: data coming from the line. \
Internal: data going to the line.;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.2.2.1.2 |
mcm4400t1e1DPTestCmdTableNAME = ;
DESC = The T1/E1 Data Port Test Command \
table. \
HELP = ;
CAPABILITIES = NET_OPER, VPN_OPER ; SEQUENCE OF Mcm4400t1e1DPTestCmdEntry .micom-oscar.22.2.3 |
mcm4400t1e1DPTestCmdEntryNAME = ;
DESC = An entry in the T1/E1 Data Port \
Test Command table.;
HELP = ;
CAPABILITIES = ; Mcm4400t1e1DPTestCmdEntry .micom-oscar.22.2.3.1 |
mcm4400t1e1DPTestCmdPortNumNAME = ;
DESC = The T1/E1 Port Number specifies which data \
port is to be tested. Used as the index to the \
T1/E1 Data Port Test Command table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.2.3.1.1 |
mcm4400t1e1DPTestCmdTstPatternNAME = ;
DESC = Setting this object will initiate various \
tests on the specified T1/E1 data port.;
HELP = External: loop back data coming from the \
device attached to the port. \
Internal: loop back data coming from the \
DS0 channel.;
CAPABILITIES = ;rw Enumeration .micom-oscar.22.2.3.1.2 |
mcm4400t1e1SysControlActionCmdNAME = ;
DESC = Setting this object will perform various \
actions on the T1/E1 system. \
Note: Starting with software release 3.0, \
the enumeration clearCounter (3) is \
not supported. The enumeration is included \
here only to support backwards compatibility \
for software versions prior to release 3.0.;
HELP = 1: initiate LED test. \
2: reset T1/E1 module. \
3: clear statistics counters. \
4: download code. \
5: stop DS0 channel test. \
6: stop line test. \
7: stop port test. \
8: stop LED test. \
9: stop all tests.;
CAPABILITIES = NET_OPER, VPN_OPER ;rw Enumeration .micom-oscar.22.2.4 |
t1e1-r2-status OBJECT IDENTIFIER .micom-oscar.22.3 |
mcm4400t1e1LineStatusTableNAME = ;
DESC = The T1/E1 Line Status Display table. \
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1LineStatusEntry .micom-oscar.22.3.1 |
mcm4400t1e1LineStatusEntryNAME = ;
DESC = An entry in the T1/E1 Line Status Display \
table.;
HELP = ;
CAPABILITIES = ; Mcm4400t1e1LineStatusEntry .micom-oscar.22.3.1.1 |
mcm4400t1e1LineStatusLineIndexNAME = ;
DESC = The T1/E1 line index specifies which line is to \
be displayed. Used as an index to the \
T1/E1 Line Status Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.1 |
mcm4400t1e1LineStatusInterfaceNAME = ;
DESC = The value of this object indicates the interface \
type as either T1 or E1 for the \
T1/E1 Line Status Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.2 |
mcm4400t1e1LineStatusImpedanceNAME = ;
DESC = The value of this object indicates the impedance \
for the specified line.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.3 |
mcm4400t1e1LineStatusTestModeNAME = ;
DESC = The value of this object indicates if the specified \
line is in a loopback test mode.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.4 |
mcm4400t1e1LineStatusTestingDS0ChNAME = ;
DESC = The value of this object indicates which DS0 \
channel is in channel loopback or channel pattern \
test mode now.;
HELP = 0: none.\
1-30: DS0 channel number.;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.3.1.1.5 |
mcm4400t1e1LineStatusAISAlarmNAME = ;
DESC = The value of this object indicates if the AIS \
(Alarm Indication Signal) alarm is preset for \
the specified line.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.6 |
mcm4400t1e1LineStatusRedAlarmNAME = ;
DESC = The value of this object indicates if the Red \
alarm is preset for the specified line.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.7 |
mcm4400t1e1LineStatusYellowAlarmNAME = ;
DESC = The value of this object indicates if the Yellow \
alarm is preset for the specified line. (Not \
applicable in E1.) ;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.8 |
mcm4400t1e1LineStatusTS16AISNAME = ;
DESC = The value of this object indicates if the TS16 \
(Time Slot 16) AIS alarm is preset for the \
specified line. (Not applicable in T1.) ;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.9 |
mcm4400t1e1LineStatusOOSMFAlarmNAME = ;
DESC = The value of this object indicates if the \
OOSMF (Out Of Signal Multi-Frame) alarm \
is preset for the specified line. (Not \
applicable in T1.) ;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.10 |
mcm4400t1e1LineStatusMFASAlarmNAME = ;
DESC = The value of this object indicates if the \
MFAS (Multi-Frame Alignment Signal - \
Y bit) alarm is preset for the specified line. \
(Not applicable in T1.) ;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.11 |
mcm4400t1e1LineStatusFASAlarmNAME = ;
DESC = The value of this object indicates if the \
FAS (Frame Alignment Signal - A bit) \
alarm is preset for the specified line. \
(Not applicable in T1.) ;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.12 |
mcm4400t1e1LineStatusOOCMFAlarmNAME = ;
DESC = The value of this object indicates if the \
OOCMF (Out Of CRC Multi-Frame) \
alarm is preset for the specified line. \
(Not applicable in T1.) ;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.1.1.13 |
mcm4400t1e1SysStatusGroup OBJECT IDENTIFIER .micom-oscar.22.3.2 |
mcm4400t1e1SysStatusCardTypeNAME = ;
DESC = The value of this object indicates the T1/E1 \
card type.;
HELP = 1: TAM1 - network line only. \
2: TAM2 - both local and network lines. \
3: EAM1 - network line only. \
4: EAM2 - both local and network lines.;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Enumeration .micom-oscar.22.3.2.1 |
mcm4400t1e1SysStatusOperStatusNAME = ;
DESC = The value of this object indicates the operation \
status of the T1/E1 control unit.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Enumeration .micom-oscar.22.3.2.2 |
mcm4400t1e1SysStatusLEDTestNAME = ;
DESC = The value of this object specifies if the \
LED test is in progress.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Enumeration .micom-oscar.22.3.2.3 |
mcm4400t1e1SysStatusSelfTestResultsNAME = ;
DESC = The value of this object specifies the \
results of the T1/E1 self test.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Enumeration .micom-oscar.22.3.2.4 |
mcm4400t1e1SysStatusFlashEPROMStNAME = ;
DESC = The value of this object specifies the current \
state of the flash EPROM in the T1/E1 \
access board.;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Enumeration .micom-oscar.22.3.2.5 |
mcm4400t1e1SysStatusApplSwIDNAME = ;
DESC = The value of this object indicates the T1/E1 \
application software ID (Null terminated string).;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro DisplayString .micom-oscar.22.3.2.6 |
mcm4400t1e1SysStatusBootSwVerNAME = ;
DESC = The value of this object indicates the T1/E1 \
software version (Null terminated string).;
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG ;ro DisplayString .micom-oscar.22.3.2.7 |
mcm4400t1e1DPStatusTableNAME = ;
DESC = The T1/E1 Data Port Status Display table. \
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1DPStatusEntry .micom-oscar.22.3.3 |
mcm4400t1e1DPStatusEntryNAME = ;
DESC = An entry in the T1/E1 Data Port Status \
Display table.;
HELP = ;
CAPABILITIES = ; Mcm4400t1e1DPStatusEntry .micom-oscar.22.3.3.1 |
mcm4400t1e1DPStatusPortNumberNAME = ;
DESC = The value of this object specifies the data port \
number. Used as the index to the T1/E1 \
Data Port Status Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.3.1.1 |
mcm4400t1e1DPStatusDTRInputStNAME = ;
DESC = The value of this object indicates the current \
DTR state for the specified data port.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.3.1.2 |
mcm4400t1e1DPStatusRTSInputStNAME = ;
DESC = The value of this object indicates the current \
RTS state for the specified data port.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.3.1.3 |
mcm4400t1e1DPStatusDSROutputStNAME = ;
DESC = The value of this object indicates the current \
DSR state for the specified data port.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.3.1.4 |
mcm4400t1e1DPStatusDCDOutputStNAME = ;
DESC = The value of this object indicates the current \
DCD state for the specified data port.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.3.1.5 |
mcm4400t1e1DPStatusCTSOutputStNAME = ;
DESC = The value of this object indicates the current \
CTS state for the specified data port.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.3.1.6 |
mcm4400t1e1DS0ChSigTableNAME = ;
DESC = The T1/E1 DS0 Channel Signaling Display \
table. \
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1DS0ChSigEntry .micom-oscar.22.3.4 |
mcm4400t1e1DS0ChSigEntryNAME = ;
DESC = An entry in the T1/E1 DS0 Channel \
Signaling Display table.;
HELP = ;
CAPABILITIES = ; Mcm4400t1e1DS0ChSigEntry .micom-oscar.22.3.4.1 |
mcm4400t1e1DS0ChSigLineIDNAME = ;
DESC = The T1/E1 line ID specifies which line is to \
be displayed. Used as an index to the \
T1/E1 DS0 Channel Signaling Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.3.4.1.1 |
mcm4400t1e1DS0ChSigDS0IndexNAME = ;
DESC = The DS0 Index specifies which time slot is \
to be displayed. Used as an index to the \
T1/E1 DS0 Channel Signaling Display table.;
HELP = For T1, 24 is the maximum. An error will be \
returned if a value greater than 24 is selected.;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.3.4.1.2 |
mcm4400t1e1DS0ChSigInABCDBitsNAME = ;
DESC = The value of this object indicates the input \
ABCD bit pattern.;
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.3.4.1.3 |
mcm4400t1e1DS0ChSigOutABCDBitsNAME = ;
DESC = The value of this object indicates the output \
ABCD bit pattern.;
HELP = ;
CAPABILITIES = ;ro INTEGER .micom-oscar.22.3.4.1.4 |
mcm4400t1e1ChTestResultsGroup OBJECT IDENTIFIER .micom-oscar.22.3.5 |
mcm4400t1e1ChTestResultsLineIDNAME = ;
DESC = The line ID specifies which T1/E1 line has \
a DS0channel in test mode.;
HELP = 3 is returned if no DS0 channel is in test mode.;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Enumeration .micom-oscar.22.3.5.1 |
mcm4400t1e1ChTestResultsDS0ChNAME = ;
DESC = The value of this object specifies which DS0 \
channel is in test mode.;
HELP = For T1, 24 is the maximum. Also, 0 will be \
returned if no DS0 channels are in test mode.;
CAPABILITIES = NET_CFG, VPN_CFG ;ro INTEGER .micom-oscar.22.3.5.2 |
mcm4400t1e1ChTestResultsErrorCntNAME = ;
DESC = The value of this object indicates the number \
of errors accumulated since the test had been \
started.;
HELP = An error can be detected only when in channel \
pattern test mode. Channel loopback will always \
be 0.;
CAPABILITIES = NET_CFG, VPN_CFG ;ro Counter .micom-oscar.22.3.5.3 |
t1e1-r2-statistics OBJECT IDENTIFIER .micom-oscar.22.4 |
mcm4400t1e1LineStatsTableNAME = ;
DESC = The T1/E1 Line Statistics Display table. \
HELP = ;
CAPABILITIES = NET_CFG, VPN_CFG; SEQUENCE OF Mcm4400t1e1LineStatsEntry .micom-oscar.22.4.1 |
mcm4400t1e1LineStatsEntryNAME = ;
DESC = An entry in the T1/E1 Line Statistics \
Display table.;
HELP = ;
CAPABILITIES = ; Mcm4400t1e1LineStatsEntry .micom-oscar.22.4.1.1 |
mcm4400t1e1LineStatsLineIndexNAME = ;
DESC = The T1/E1 line index specifies which line is to \
be displayed. Used as an index to the \
T1/E1 Line Statistics Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.4.1.1.1 |
mcm4400t1e1LineStatsInterfaceNAME = ;
DESC = The value of this object indicates the interface \
type as either T1 or E1 for the \
T1/E1 Line Statistics Display table.;
HELP = ;
CAPABILITIES = ;ro Enumeration .micom-oscar.22.4.1.1.2 |
mcm4400t1e1LineStatsFramingBitErrorNAME = ;
DESC = The value of this object indicates the framing \
bit errors on the specified line.;
HELP = Valid for E1 only. For T1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.3 |
mcm4400t1e1LineStatsLineCdViolationNAME = ;
DESC = The value of this object indicates the line \
code violations on the specified line.;
HELP = ;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.4 |
mcm4400t1e1LineStatsFarEndBlkErrorNAME = ;
DESC = The value of this object indicates the far \
end block errors on the specified line.;
HELP = Valid for E1 only. For T1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.5 |
mcm4400t1e1LineStatsCRCErrorNAME = ;
DESC = The value of this object indicates the CRC \
errors on the specified line.;
HELP = Valid for E1 only. For T1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.6 |
mcm4400t1e1LineStatsBufferOverrunNAME = ;
DESC = The value of this object indicates the \
buffer overruns on the specified line.;
HELP = Valid for E1 only. For T1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.7 |
mcm4400t1e1LineStatsBufferUnderrunNAME = ;
DESC = The value of this object indicates the \
buffer underruns on the specified line.;
HELP = Valid for E1 only. For T1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.8 |
mcm4400t1e1LineStatsFrmSyncBitErrorNAME = ;
DESC = The value of this object indicates the frame \
synchronization bit errors on the specified line.;
HELP = Valid for T1 only. For E1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.9 |
mcm4400t1e1LineStatsOutOfFrameNAME = ;
DESC = The value of this object indicates the out of \
frame statistics on the specified line.;
HELP = Valid for T1 only. For E1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.10 |
mcm4400t1e1LineStatsTotalFrameSlipNAME = ;
DESC = The value of this object indicates the total \
frame slips on the specified line.;
HELP = Valid for T1 only. For E1, 0 will be returned.;
CAPABILITIES = ;ro Counter .micom-oscar.22.4.1.1.11 |