LANPLEX-OPT-FDDI-MIB-1-2-2
AI MIB Summary
Standard SNMP MIB module defining data structures for LANPLEX-OPT-FDDI-MIB-1-2-2.
67
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
67 total| Object Name |
|---|
lanplexOptFddi OBJECT IDENTIFIER .1.3.6.1.4.1.114.1.10 |
RFC1155-SMI Unknown .1.3.6.1.4.1.114.1.10 |
lpOptSMTHoldConditionGenerated when fddiSMTHoldState (fddimibSMTHoldState)
assumes the state holding-prm or holding-sec. This
notification is a Condition in the Status Report
Protocol (see 7.2.7 and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.1 |
lpOptSMTPeerWrapConditionThis condition is active when fddiSMTPeerWrapFlag
(fddimibSMTPeerWrapFlag) is set. This notification is
a Condition in the Status Report Protocol (see 7.2.7
and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.2 |
lpOptMACDuplicateAddressConditionThis condition is active when either fddiMACDA-Flag
(fddimibMACDaFlag) or fddiMACUNDA-Flag
(fddimibMACUnaDaFlag) is set. This event is handled
as a Condition in the Status Report Protocol (see 7.2.7
and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.3 |
lpOptMACFrameErrorConditionGenerated when the fddiMACFrameErrorRatio
(fddimibMACFrameErrorRatio) is greater than or equal
to fddiMACFrameErrorThreshold
(fddimibMACFrameErrorThreshold). This event is handled
as a Condition in the Status Report Protocol (see 7.2.7
and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.4 |
lpOptMACNotCopiedConditionGenerated when the fddiMACNotCopiedRatio
(fddimibMACNotCopiedRatio) is greater than or equal to
the fddiMACNotCopiedThreshold (lpOptMACNotCopiedThreshold).
This event is handled as a Condition in the Status Report
Protocol (see 7.2.7 and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.5 |
lpOptMACNeighborChangeEventGenerated when a change in a MAC's upstream neighbor
address or downstream neighbor address is detected.
(see 7.2.7 and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.6 |
lpOptMACPathChangeEventThis event is generated when the value of the
fddiMACCurrentPath (fddimibMACCurrentPath) changes.
This event shall be supressed if the value changes
from isolated to local or local to isolated (see
7.2.7 and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.7 |
lpOptPORTLerConditionThis condition becomes active when the value of
fddiPORTLer-Estimate (fddimibPORTLerEstimate)
is less than or equal to fddiPORTLer-Alarm
(fddimibPORTLerAlarm). This will be reported
with the Status Report Frames (SRF) (see 7.2.7
and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.8 |
lpOptPORTUndesiredConnAttemptEventGenerated when an undesired connection attempt has
been made (see 5.2.4, 7.2.7, and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.9 |
lpOptPORTEBErrorConditionGenerated when the Elasticity Buffer Error-Ct
(lpOptPORTEBErrorCt) increments. This is handled
as a condition in the Status Report Protocol. It
is generated when an increment occurs in the
station's sampling period (see 7.2.7 and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.10 |
lpOptPORTPathChangeEventThis event is generated when the value of the
fddiPORTCurrentPath (lpOptPORTCurrentPath)
changes. This event shall be surpressed if the
value changes from isolated to local or local
to isolated (see 7.2.7 and 8.3). TRAP-TYPE .1.3.6.1.4.1.114.1.10.0.11 |
lpOptSMT OBJECT IDENTIFIER .1.3.6.1.4.1.114.1.10.1 |
lpOptSMTTableA list of optional SMT entries. The number of entries
shall not exceed the value of snmpFddiSMTNumber. SEQUENCE OF LpOptSMTEntry .1.3.6.1.4.1.114.1.10.1.1 |
lpOptSMTEntryAn optional SMT entry containing information common to
a given optional SMT. LpOptSMTEntry .1.3.6.1.4.1.114.1.10.1.1.1 |
lpOptSMTIndexA unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.114.1.10.1.1.1.1 |
lpOptSMTManufacturerOUIThe three octets of manufacturer data which make
up the manufacturerOUI component.ro OCTET STRING .1.3.6.1.4.1.114.1.10.1.1.1.2 |
lpOptSMTManufacturerDataThe 29 octets of manufacturer data which make up the
manufacturerData component.ro OCTET STRING .1.3.6.1.4.1.114.1.10.1.1.1.3 |
lpOptSMTHoldStateThis variable indicates the current state of the
Hold function. The value 'not-holding' is the
default and initial value. The value must be set
to 'not-holding' as part of Active_Actions and
when the conditions causing 'holding-prm' or
'holding-sec' are no longer true. The value
'holding-prm' must be set when the condition
(notTR_Flag & not RE_Flag & (PC_LS=QLS | LEM_Fail
| TNE>NS_Max | (not LS_Flag & TPC > T_Out))) is
satisfied in state PC8:ACTIVE for the A Port. The
value 'holding-sec' must be set when the condition
(notTR_Flag & not RE_Flag & (PC_LS=QLS | LEM_Fail
| TNE>NS_Max | (not LS_Flag & TPC > T_Out))) is
satisfied in state PC8:ACTIVE for the B Port.ro Enumeration .1.3.6.1.4.1.114.1.10.1.1.1.4 |
lpOptSMTSetCountThis variable is composed of a count incremented
in response to a Set operation on the MIB, and the
time of the change, however only the count is
reported here (refer to ANSI SMT 8.4.1).ro INTEGER .1.3.6.1.4.1.114.1.10.1.1.1.5 |
lpOptSMTLastSetStationIdThe Station ID of the station that effected the last
change in the FDDI MIB.ro FddiSMTStationIdType .1.3.6.1.4.1.114.1.10.1.1.1.6 |
lpOptMAC OBJECT IDENTIFIER .1.3.6.1.4.1.114.1.10.2 |
lpOptMACBridgeFunctionTableA list of MAC bridge function entries. SEQUENCE OF LpOptMACBridgeFunctionEntry .1.3.6.1.4.1.114.1.10.2.1 |
lpOptMACBridgeFunctionEntryBridge function information for a given MAC
within a given SMT. LpOptMACBridgeFunctionEntry .1.3.6.1.4.1.114.1.10.2.1.1 |
lpOptMACBridgeFunctionSMTIndexA unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.114.1.10.2.1.1.1 |
lpOptMACBridgeFunctionMACIndexIndex variable for uniquely identifying the MAC
object instances.ro INTEGER .1.3.6.1.4.1.114.1.10.2.1.1.2 |
lpOptMACBridgeFunctionsIndicates the MAC's optional bridging functions.
The Value -1 is used to indicate that bridging is
not supported by this MAC.
The value is a sum. This value initially takes
the value zero, then for each function present, 2
raised to a power is added to the sum. The powers
are according to the following table:
Function Power
tb 0
sr 1
srt 2ro INTEGER (-1..7) .1.3.6.1.4.1.114.1.10.2.1.1.3 |
lpOptMACTPriTableA list of MAC T-Pri entries. SEQUENCE OF LpOptMACTPriEntry .1.3.6.1.4.1.114.1.10.2.2 |
lpOptMACTPriEntryA collection of T-Pri information for a given MAC within
a given SMT. LpOptMACTPriEntry .1.3.6.1.4.1.114.1.10.2.2.1 |
lpOptMACTPriSMTIndexA unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.114.1.10.2.2.1.1 |
lpOptMACTPriMACIndexIndex variable for uniquely identifying the MAC
object instances.ro INTEGER .1.3.6.1.4.1.114.1.10.2.2.1.2 |
lpOptMACTPri0This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units.ro FddiTimeNano .1.3.6.1.4.1.114.1.10.2.2.1.3 |
lpOptMACTPri1This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units.ro FddiTimeNano .1.3.6.1.4.1.114.1.10.2.2.1.4 |
lpOptMACTPri2This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units.ro FddiTimeNano .1.3.6.1.4.1.114.1.10.2.2.1.5 |
lpOptMACTPri3This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units.ro FddiTimeNano .1.3.6.1.4.1.114.1.10.2.2.1.6 |
lpOptMACTPri4This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units.ro FddiTimeNano .1.3.6.1.4.1.114.1.10.2.2.1.7 |
lpOptMACTPri5This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units.ro FddiTimeNano .1.3.6.1.4.1.114.1.10.2.2.1.8 |
lpOptMACTPri6This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units.ro FddiTimeNano .1.3.6.1.4.1.114.1.10.2.2.1.9 |
lpOptPATH OBJECT IDENTIFIER .1.3.6.1.4.1.114.1.10.3 |
lpOptPATHRingTableA list of PATH ring entries. SEQUENCE OF LpOptPATHRingEntry .1.3.6.1.4.1.114.1.10.3.1 |
lpOptPATHRingEntryRing latency, trace status, and T-Rmode information for a
given PATH within a given SMT. LpOptPATHRingEntry .1.3.6.1.4.1.114.1.10.3.1.1 |
lpOptPATHRingSMTIndexA unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.114.1.10.3.1.1.1 |
lpOptPATHRingPATHIndexIndex variable for uniquely identifying the
primary, secondary and local PATH object
instances. Local PATH object instances are
represented with integer values 3 to 255.ro INTEGER .1.3.6.1.4.1.114.1.10.3.1.1.2 |
lpOptPATHRingLatencyGives the total accumulated latency of the ring
associated with this path. May be measured directly
by the station or calculated by a management station.
Values of this object are reported in 1 ns units.rw FddiTimeNano .1.3.6.1.4.1.114.1.10.3.1.1.3 |
lpOptPATHTraceStatusThis attribute indicates the current trace status of
the path.
The value is a sum which represents all of the trace
status information which applies. This value initially
takes the value zero, then for each condition which
applies, 2 raised to a power is added to the sum. the
powers are according to the following table:
TraceStatus Power
traceinitiated 0
tracepropragated 1
traceterminated 2
tracetimeout 3ro INTEGER .1.3.6.1.4.1.114.1.10.3.1.1.4 |
lpOptPATHT-RmodeUsed by RMT to limit the duration of restricted dialogs
on a path. This object is reported in 1 ns units.rw FddiTimeNano .1.3.6.1.4.1.114.1.10.3.1.1.5 |
lpOptPATHSbaTableA list of PATH Sba entries. SEQUENCE OF LpOptPATHSbaEntry .1.3.6.1.4.1.114.1.10.3.2 |
lpOptPATHSbaEntrySba information for a given PATH within a given SMT. LpOptPATHSbaEntry .1.3.6.1.4.1.114.1.10.3.2.1 |
lpOptPATHSbaSMTIndexA unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.114.1.10.3.2.1.1 |
lpOptPATHSbaPATHIndexIndex variable for uniquely identifying the
primary, secondary and local PATH object
instances. Local PATH object instances are
represented with integer values 3 to 255.ro INTEGER .1.3.6.1.4.1.114.1.10.3.2.1.2 |
lpOptPATHSbaPayloadThe payload portion of the Synchronous Bandwidth
Allocation for thi path. This value represents the
maximum number of bytes of data allocated for
transmission per 125 microseconds.rw INTEGER .1.3.6.1.4.1.114.1.10.3.2.1.3 |
lpOptPATHSbaOverheadThe overhead portion of the Synchronous Bandwith
Allocation for this path. This value repersents the
maximum number of bytes overhead (token capture, frame
header, etc.) used pre negotiated Target Token Rotation
Time (T_neg).rw INTEGER .1.3.6.1.4.1.114.1.10.3.2.1.4 |
lpOptPATHSbaAvailableThis value is the maximum Synchronous Bandwith available
for a path in bytes per second.rw INTEGER .1.3.6.1.4.1.114.1.10.3.2.1.5 |
lpOptPORT OBJECT IDENTIFIER .1.3.6.1.4.1.114.1.10.4 |
lpOptPORTTableA list of optional PORT entries. SEQUENCE OF LpOptPORTEntry .1.3.6.1.4.1.114.1.10.4.1 |
lpOptPORTEntryMAC loop time and EB error count information for a
given PORT within a given SMT. LpOptPORTEntry .1.3.6.1.4.1.114.1.10.4.1.1 |
lpOptPORTSMTIndexA unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.114.1.10.4.1.1.1 |
lpOptPORTIndexIndex variable for uniquely identifying the PORT
object instances.ro INTEGER .1.3.6.1.4.1.114.1.10.4.1.1.2 |
lpOptPORTMACLoopTimeThis attribute controls the value used for T_Next(9)
(see 9.4.4.2.3). This object is reported in 1 ns
units.rw FddiTimeNano .1.3.6.1.4.1.114.1.10.4.1.1.3 |
lpOptPORTEBErrorCtA count that should as closely as possible match the
times an Elasticity Buffer Error has occurred while in
active line state.ro Counter .1.3.6.1.4.1.114.1.10.4.1.1.4 |
lpOptPORTLSTableA list of optional PORT line state entries. SEQUENCE OF LpOptPORTLSEntry .1.3.6.1.4.1.114.1.10.4.2 |
lpOptPORTLSEntryMaintenance line state and PC line state information
for a given PORT within a given SMT. LpOptPORTLSEntry .1.3.6.1.4.1.114.1.10.4.2.1 |
lpOptPORTLSSMTIndexA unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization.ro INTEGER .1.3.6.1.4.1.114.1.10.4.2.1.1 |
lpOptPORTLSPORTIndexIndex variable for uniquely identifying the PORT
object instances.ro INTEGER .1.3.6.1.4.1.114.1.10.4.2.1.2 |
lpOptPORTMaintLSThe PORT Maintenance Line State specifies the line state
(Maint_LS) to be transmitted when the PCM state machine
for the port is in state PC9 Maint.rw Enumeration .1.3.6.1.4.1.114.1.10.4.2.1.3 |
lpOptPORTPCLSThis attribute indicates the line state (PC_LS) received
by the port.ro Enumeration .1.3.6.1.4.1.114.1.10.4.2.1.4 |