Juniper-UNI-SONET-MIB
AI MIB Summary
The Juniper-UNI-SONET-MIB extends standard SONET monitoring on Juniper Networks hardware by exposing configuration parameters for SONET interface attributes that are absent or read-only in the standard SONET-MIB. This module enables granular control over physical layer interface settings, such as framing, line coding, and signal timing, to facilitate precise provisioning and troubleshooting of optical transport links.
The SONET MIB for the Juniper Networks enterprise. This MIB contains managed objects for SONET interfaces. It contains management objects for configuration of interface attributes that either are absent from, or read-only in the standard SONET-MIB.
Main OID:
juniSonetMIB.1.3.6.1.4.1.4874.2.2.7
68
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
68 total| Object Name |
|---|
juniSonetMIBThe SONET MIB for the Juniper Networks enterprise. This MIB contains managed objects for SONET interfaces. It contains management objects for configuration of interface attributes that either are absent from, or read-only in the standard SONET-MIB. MODULE-IDENTITY .1.3.6.1.4.1.4874.2.2.7 |
juniSonetObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.1 |
juniSonetMediumTableThis table contains entries for SONET interfaces present in the system. SEQUENCE OF JuniSonetMediumEntry .1.3.6.1.4.1.4874.2.2.7.1.1 |
juniSonetMediumEntryEach entry describes the characteristics of an SONET interface. JuniSonetMediumEntry .1.3.6.1.4.1.4874.2.2.7.1.1.1 |
juniSonetMediumTypeThis variable identifies whether a SONET or a SDH signal is used across this interface. This object was deprecated because the same information is provided by the SONET-MIB.sonetMediumType object (RFC 2558).rwdeprecated Enumeration .1.3.6.1.4.1.4874.2.2.7.1.1.1.1 |
juniSonetMediumLoopbackConfigThe current loopback state of the SONET/SDH interface. The values mean: sonetNoLoop Not in the loopback state. A device that is not capable of performing a loopback on this interface shall always return this value. sonetFacilityLoop The received signal at this interface is looped back out through the corresponding transmitter in the return direction. sonetTerminalLoop The signal that is about to be transmitted is connected to the associated incoming receiver. sonetOtherLoop Loopbacks that are not defined here.rw Enumeration .1.3.6.1.4.1.4874.2.2.7.1.1.1.2 |
juniSonetMediumTimingSourceSelects the source from which transmit timing is derived. loop timing is recovered from the receiver internalModule timing is from the module associated with this interface internalChassis timing is taken from the internal system timing referencerw Enumeration .1.3.6.1.4.1.4874.2.2.7.1.1.1.3 |
juniSonetMediumCircuitIdentifierThis variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. This object was deprecated because the same information is provided by the SONET-MIB.sonetMediumCircuitIdentifier object (RFC 2558).rwdeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.7.1.1.1.4 |
juniSonetMediumTriggerAlarmsThe alarms that are used in the operational status calculation for this SONET interface. sectionLOS When this bit is set, section LOS is used for operational status calculation. sectionLOF When this bit is set, section LOF is used for operational status calculation. lineAIS When this bit is set, line AIS is used for operational status calculation. lineRDI When this bit is set, line RDI is used for operational status calculation. The value of this object defaults to all the bits set, indicating all of the alarms are used for the operational status calculation.ro Bits .1.3.6.1.4.1.4874.2.2.7.1.1.1.5 |
juniSonetMediumTriggerDelayThe time delay (in milliseconds) before a defect is accepted as an alarm for this SONET interface.rw Integer32 .1.3.6.1.4.1.4874.2.2.7.1.1.1.6 |
juniSonetPathObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.2 |
juniSonetPathCapabilityTableThis table contains entries for SONET Paths present in the system. SEQUENCE OF JuniSonetPathCapabilityEntry .1.3.6.1.4.1.4874.2.2.7.2.1 |
juniSonetPathCapabilityEntryEach entry describes the SONET path capability of a SONET interface. This table is index by the ifIndex of the SONET interface. JuniSonetPathCapabilityEntry .1.3.6.1.4.1.4874.2.2.7.2.1.1 |
juniSonetPathRemoveFlagThis variable identifies whether a SONET/SDH supports the deletion of SONET Paths. A value of true(1) indicates the SONET path is removable; a value of false(2) indicates the SONET path cannot be removed.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.7.2.1.1.1 |
juniSonetPathChannelizedIdentifies whether or not this SONET interface supports channelization. A value of true(1) indicates the SONET path is channelized; a value of false(2) indicates the SONET path is not channelized.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.7.2.1.1.2 |
juniSonetPathMaximumChannelsIdentifies the maximum number of SONET paths/channels for this interface.ro Unsigned32 .1.3.6.1.4.1.4874.2.2.7.2.1.1.3 |
juniSonetPathMinimumPathSpeedIdentifies the minimum SONET path speed for this interface.ro JuniSonetLineSpeed .1.3.6.1.4.1.4874.2.2.7.2.1.1.4 |
juniSonetPathMaximumPathSpeedIdentifies the maximum SONET path speed for this interface.ro JuniSonetLineSpeed .1.3.6.1.4.1.4874.2.2.7.2.1.1.5 |
juniSonetPathNextIfIndexCoordinate ifIndex value allocation for entries in juniSonetPathTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.ro JuniNextIfIndex (Juniper-TC) .1.3.6.1.4.1.4874.2.2.7.2.2 |
juniSonetPathTableThis table contains entries for SONET Path interfaces present in the system. SEQUENCE OF JuniSonetPathEntry .1.3.6.1.4.1.4874.2.2.7.2.3 |
juniSonetPathEntryEach entry describes the characteristics of an SONET Path interface. JuniSonetPathEntry .1.3.6.1.4.1.4874.2.2.7.2.3.1 |
juniSonetPathIfIndexThe ifIndex of the SONET Path interface. When creating entries in this table, suitable values for this object are determined by reading juniSonetPathNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.7.2.3.1.1 |
juniSonetPathLogicalChannelThe logical channel number assigned to this SONET Path. If the underlying SONET interface does not support channelization, the value of this object is zero.rw JuniSonetLogicalPathChannel .1.3.6.1.4.1.4874.2.2.7.2.3.1.2 |
juniSonetPathSpeedThe line speed associated with this SONET PATH.rw JuniSonetLineSpeed .1.3.6.1.4.1.4874.2.2.7.2.3.1.3 |
juniSonetPathHierarchyThe SONET Path hierarchy associated with this path.rw JuniSonetPathHierarchy .1.3.6.1.4.1.4874.2.2.7.2.3.1.4 |
juniSonetPathLowerIfIndexThe ifIndex of the interface over which this SONET Path interface is to be layered - typically a SONET/SDH interface. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.7.2.3.1.5 |
juniSonetPathRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniSonetPathRowStatus juniSonetPathSpeed juniSonetPathHierarchy juniSonetPathLowerIfIndex The logical channel may optionally be specified. If it is not specified an unused logical channel value will be assigned by the system. juniSonetPathLogicalChannel In addition, when creating an entry the following conditions must hold: A value for juniSonetPathIfIndex must have been determined previously, by reading juniSonetPathNextIfIndex. The interface identified by the juniSonetPathLowerIfIndex must exist. The juniSonetPathSpeed must be consistent with the speed for the channel specified by the juniSonetPathHierarchy, based on the speed of the interface identified by the juniSonetPathLowerIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.7.2.3.1.6 |
juniSonetPathTriggerAlarmsThe path alarms that are used in the operational status calculation for this SONET Path. pathLOP When this bit is set, path LOP is used for operational status calculation. This bit may not be modified. pathAIS When this bit is set, path AIS is used for operational status calculation. This bit may not be modified. pathRDI When this bit is set, path RDI is used for operational status calculation. The value of this object defaults to bits 0 and 1 set, indication LOP and AIS will be used for operational status calculation this SONET Path.rw Bits .1.3.6.1.4.1.4874.2.2.7.2.3.1.7 |
juniSonetPathC2ByteOverrideFlagThe path overhead c2 transmit override enable. If set to true(1), juniSonetPathC2Byte override value must be specified. If set to false(2), c2 byte will be automatically set by the system based on the upper interface type.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.7.2.3.1.8 |
juniSonetPathC2ByteOverrideThe path overhead c2 transmit and expected value for this SONET Path.rw JuniSonetPathC2ByteOverride .1.3.6.1.4.1.4874.2.2.7.2.3.1.9 |
juniSonetPathTriggerDelayThe time delay (in milliseconds) before a defect is accepted as an alarm for this SONET Path.rw Integer32 .1.3.6.1.4.1.4874.2.2.7.2.3.1.10 |
juniSonetPathEventStatusThis variable specifies which events have occurred in the current 15 minute interval. The value represents a vector of bits, each specifying a unique event: - Bit 0 Rising threshold alarm, sonetPathCurrentESs. - Bit 1 Rising threshold alarm, sonetPathCurrentSESs. - Bit 2 Reserved. - Bit 3 Rising threshold alarm, sonetPathCurrentCVs. - Bit 4 Rising threshold alarm, sonetPathCurrentUASs. - Bit 5 LOP failure indication. - Bit 6 LOP failure cleared. - Bit 7 AIS failure indication. - Bit 8 AIS failure cleared. - Bit 9 RFI indication. - Bit 10 RFI cleared. - Bit 11 UNEQ failure indication. - Bit 12 UNEQ failure cleared. - Bit 13 PLM failure indication. - Bit 14 PLM failure cleared.ro Unsigned32 .1.3.6.1.4.1.4874.2.2.7.2.3.1.11 |
juniSonetVTObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.3 |
juniSonetVTNextIfIndexCoordinate ifIndex value allocation for entries in juniSonetVTTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.ro JuniNextIfIndex (Juniper-TC) .1.3.6.1.4.1.4874.2.2.7.3.1 |
juniSonetVTTableThis table contains entries for SONET Virtual Tributary interfaces present in the system. This table augments the standard SONET-MIB.sonetVTCurrentTable. SEQUENCE OF JuniSonetVTEntry .1.3.6.1.4.1.4874.2.2.7.3.2 |
juniSonetVTEntryEach entry describes the characteristics of an SONET Virtual Tributary interface. JuniSonetVTEntry .1.3.6.1.4.1.4874.2.2.7.3.2.1 |
juniSonetVTIfIndexThe ifIndex of the SONET Virtual Tributary interface. When creating entries in this table, suitable values for this object are determined by reading juniSonetVTNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.7.3.2.1.1 |
juniSonetVTPathLogicalChannelThe SONET Path logical channel number associated with this virtual tributary.rw JuniSonetLogicalPathChannel .1.3.6.1.4.1.4874.2.2.7.3.2.1.2 |
juniSonetVTTypeThe SONET virtual tributary type. This object was deprecated because the same information is provided in the SONET-MIB.sonetVTCurrentWidth object.rwdeprecated JuniSonetVTType .1.3.6.1.4.1.4874.2.2.7.3.2.1.3 |
juniSonetVTPathPayloadThe SONET Path payload number associated with this virtual tributary. For SDH mode, this is a value with a range from 1-3. For SONET mode, the value of this object is always 1.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.7.3.2.1.4 |
juniSonetVTTributaryGroupThe SONET Path group number for this virtual tributary. In SONET and SDH mode, the value of this object is 1-7.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.7.3.2.1.5 |
juniSonetVTTributarySubChannelSpecifies the virtual tributary number within the tributary group defined by juniSonetVTTributaryGroup object. The value of this object ranges from 1-4 if the tributary type is tribVT15/TU11(0); and the values 1-3 if the tributary type is tribVT20/TU12(1).rw Unsigned32 .1.3.6.1.4.1.4874.2.2.7.3.2.1.6 |
juniSonetVTLowerIfIndexThe ifIndex of the interface over which this SONET Virtual Tributary interface is to be layered - typically a SONET PATH interface. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.7.3.2.1.7 |
juniSonetVTRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniSonetVTRowStatus juniSonetVTPathLogicalChannel juniSonetVTType juniSonetVTPathPayload juniSonetVTTributaryGroup juniSonetVTTributarySubChannel juniSonetVTLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniSonetVTIfIndex must have been determined previously, by reading juniSonetVTNextIfIndex. The interface identified by juniSonetVTLowerIfIndex must exist. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.7.3.2.1.8 |
juniSonetConformance OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.4 |
juniSonetCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.4.1 |
juniSonetComplianceObsolete compliance statement for entities which implement the Juniper SONET MIB. This statement became obsolete when the SONET Path and SONET VT groups of objects were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.1.1 |
juniSonetCompliance2Obsolete compliance statement for entities which implement the Juniper SONET MIB. This statement became obsolete when the juniSonetMediumType, juniSonetMediumCircuitIdentifier and juniSonetVTType objects were deprecated.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.1.2 |
juniSonetCompliance3Obsolete compliance statement for entities which implement the Juniper SONET MIB. This statement became obsolete when support was added for alarm triggers and path c2 byte override.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.1.3 |
juniSonetCompliance4Obsolete compliance statement for entities which implement the Juniper SONET MIB. This statement became obsolete when the SONET Path event status and notification support was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.1.4 |
juniSonetCompliance5The compliance statement for entities which implement the Juniper SONET MIB. Unknown .1.3.6.1.4.1.4874.2.2.7.4.1.5 |
juniSonetGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.4.2 |
juniSonetGroupObsolete collection of objects providing management of SONET/SDH interfaces in a Juniper product. This group became obsolete when the juniSonetMediumType and juniSonetMediumCircuitIdentifier objects were deprecated.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.1 |
juniSonetPathGroupObsolete collection of objects providing management of SONET/SDH Path interfaces in a Juniper product. This group became obsolete when new SONET path objects were added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.2 |
juniSonetVirtualTributaryGroupObsolete collection of objects providing management of SONET virtual tributaries in a Juniper product. This group became obsolete when juniSonetVTType was deprecated.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.3 |
juniSonetGroup2Obsolete collection of objects providing management of SONET/SDH interfaces in a Juniper product. This group became obsolete when juniSonetMediumTriggerAlarms was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.4 |
juniSonetVirtualTributaryGroup2A collection of objects providing management of SONET virtual tributaries in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.5 |
juniSonetDeprecatedMediumGroupA collection of deprecated objects providing management of SONET/SDH interfaces in a Juniper product. This group is deprecated because the same information is provided by SONET-MIB objects (RFC 2558). Support for the objects in this group will be phased out over time.deprecated Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.6 |
juniSonetDeprecatedVTGroupA deprecated object providing management of SONET/SDH VT interfaces in a Juniper product. This group is deprecated because the same information is provided by SONET-MIB objects (RFC 2558). Support for the VT type object will be phased out over time.deprecated Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.7 |
juniSonetGroup3A collection of objects providing management of SONET/SDH interfaces in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.8 |
juniSonetPathGroup2Obsolete collection of management objects providing management of SONET/SDH Path interfaces in a Juniper product. This group became obsolete when path event notification support was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.9 |
juniSonetPathGroup3A collection of objects providing management of SONET/SDH Path interfaces in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.10 |
juniSonetPathNotificationGroupA management notification for signaling SONET Path interface status changes in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.7.4.2.11 |
juniSonetTrapControl OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.5 |
juniSonetPathEventIfIndexThe ifIndex of the SONET Path interface. This is the same value as juniSonetPathIfIndex for the interface that is reporting an event.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.7.5.1 |
juniSonetTraps OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.6 |
juniSonetTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.7.6.0 |
juniSonetPathEventsThis trap reports SONET path events for the failures and normal conditions of the SONET path entity. NOTIFICATION-TYPE .1.3.6.1.4.1.4874.2.2.7.6.0.1 |