Juniper-MPLS-MIB
AI MIB Summary
The Juniper-MPLS-MIB enables monitoring and configuration of Juniper Label Switching Routers (LSRs) by exposing managed objects for global MPLS parameters, interface and tunnel settings, explicit paths, and BGP/MPLS VPN or CR-LDP constraints.
The MultiProtocol Label Switching (MPLS) MIB for the Juniper Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations.
Main OID:
juniMplsMIB.1.3.6.1.4.1.4874.2.2.54
212
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
212 total| Object Name |
|---|
juniMplsMIBThe MultiProtocol Label Switching (MPLS) MIB for the Juniper Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations. MODULE-IDENTITY .1.3.6.1.4.1.4874.2.2.54 |
juniMplsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1 |
juniMplsLsrGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.1 |
juniMplsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.1.1 |
juniMplsGroupMplsEnableEnables or disables MPLS on the virtual router. When MPLS is created on the virtual router (VR), it remains adminstratively disabled untill it is enabled explicitly. Without administratively enabling the MPLS on VR, it won't function as an LSR even though it holds the MPLS configurations until the MPLS context is destroyed for the VR.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.1 |
juniMplsGroupReopTimerAll LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. This object allows configuration of the frequency of reoptimization in time interval.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.2 |
juniMplsGroupLabelRangeLowThe lower end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.3 |
juniMplsGroupLabelRangeHighThe higher end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.4 |
juniMplsGroupLspRetryTimesNorouteThis object configures the number of retries for LSP setup after a failure due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.5 |
juniMplsGroupLspRetryIntervalNorouteThis object configures the time interval between two successive LSP setup retries after a failure due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.6 |
juniMplsGroupLspRetryTimesUse this object to configure number of retries for LSP setup after a failure other than one due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.7 |
juniMplsGroupLspRetryIntervalUse this object to configure the time interval between two LSP setup retries after a failure other than one due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.8 |
juniMplsGroupLdpRetryTimesNorouteUse this object to configure the number of retries for LDP to setup LSP after a failure due to no available route.rwobsolete Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.9 |
juniMplsGroupLdpRetryIntervalNorouteUse this object to configure the time interval between two successive LSP setup retries by LDP after a failure due to no available route.rwobsolete Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.10 |
juniMplsGroupLdpRetryTimesUse this object to configure LSP setup retries by LDP after a failure other than one due to no available route.rwobsolete Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.11 |
juniMplsGroupLdpRetryIntervalUse this object to configure time interval between two LSP setup retries by LDP after a failure other than one due to no available route.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.12 |
juniMplsGroupLdpSessionRetriesUse this object to configure the number of LDP session retries.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.13 |
juniMplsGroupLdpSessionRetryTimerUse this object to configure the time interval between two LDP session retries.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.1.14 |
juniMplsGroupTopologyDrivenIpProfileNameUsually IP interfaces are stacked on top of the MPLS tunnels. The profiled tunnels are associated with IP interfaces with profile of IP interfaces. This object configures the name for the IP profile.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.15 |
juniMplsGroupTopologyDrivenLdpEgressIpIntfThis object allows enabling/disabling of IP interfaces created over egress LSPs setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.16 |
juniMplsGroupTopologyDrivenLdpIngressIpIntfThis object allows enabling/disabling of IP interfaces created over ingress LSPs setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.17 |
juniMplsGroupTopologyDrivenLdpEgressIpIntfHostOnlyThis object allows enabling/disabling of IP interfaces created over egress LSPs to host only IP addresses setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.18 |
juniMplsGroupTopologyDrivenLdpIngressIpIntfHostOnlyThis object allows enabling/disabling of IP interfaces created over ingress LSPs to host only IP addresses setup by topology driven LSP setup configurations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.19 |
juniMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListTypeThere are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the egress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.20 |
juniMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListTypeThere are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the ingress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.21 |
juniMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListThis object used to configure egress list name of topology driven LSPs over IP interfaces. For successful configurations the egress list name must be set cunncurently with egress list type. Set the list type and list name cuncurrently.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.22 |
juniMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListThis object used to configure ingress list name of topology driven LSPs over IP interfaces. For successful configurations ingress listname set cunncurently with ingress list type. Set the list type and list name cuncurrently.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.23 |
juniMplsGroupTopologyDrivenLdpLDP is used for label distributions control for setting up the LSPs. Topology driven LSPs also setup using LDP label distribution control. This object allows to enable/disable LDP admin state used for topology driven LSPs setup.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.24 |
juniMplsGroupLspLabelDistCtrlModeSome FECs correspond to address prefixes which are distributed via a dynamic routing algorithm. The setup of the LSPs for these FECs can be done in one of two ways: Independent LSP Control or Ordered LSP Control. This object displays the LSP lable distribution control mode.ro Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.25 |
juniMplsGroupLdpAdvHostOnlyThis object allows to enable/disable LDP label advertisement mode for host only LSPs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.26 |
juniMplsGroupLsrStateThis object value displays the status of MPLS enabled LSR such as state is up or down etc.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.27 |
juniMplsGroupReopNowAll LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. Setting this object forces an immediate check for better paths for the existing LSPs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.1.28 |
juniMplsGroupIpTtlPropagateIndicate the IP TTL propagation status on ingress LSPs. none - Not set to anything. hideForwardedAndLocal - Hide LSP topology from local and forwarded traffic. hideForwarded - Hide LSP topology from forwarded traffic only. hideLocal - Hide LSP topology from local traffic only.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.1.29 |
juniMplsGroupList OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.1.2 |
juniMplsGroupTargetedHelloSendTableThis table contains list of send side IP addresses for LDP targeted hello messages. SEQUENCE OF JuniMplsGroupTargetedHelloSendEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.1 |
juniMplsGroupTargetedHelloSendEntryEach entry represents send IP address for targeted hello message. JuniMplsGroupTargetedHelloSendEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1 |
juniMplsGroupTargetedHelloSendAddressConfigure the send side address for targeted hello messages. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.1 |
juniMplsGroupLdpTargetedHelloSendModeSelect mode to add/delete to the list of IP addresses for targeted hello messages.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.2 |
juniMplsGroupTargetedHelloReceiveTableThis table contains list of receive side IP addresses for LDP targeted hello messages. SEQUENCE OF JuniMplsGroupTargetedHelloReceiveEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.2 |
juniMplsGroupTargetedHelloReceiveEntryEach entry represents receive IP address for targeted hello message. JuniMplsGroupTargetedHelloReceiveEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1 |
juniMplsGroupTargetedHelloReceiveAddressConfigure the receive side address for targeted hello messages. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.1 |
juniMplsGroupLdpTargetedHelloReceiveModeSelect mode to add/delete to the list of IP addresses for targeted hello messages.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.2 |
juniMplsGroupLdpLabelAdverRouteListTableTable is a list of LDP label advertisement entries. SEQUENCE OF JuniMplsGroupLdpLabelAdverRouteListEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.3 |
juniMplsGroupLdpLabelAdverRouteListEntryEach entry represents access list pairs for the LDP peers label advertisement. JuniMplsGroupLdpLabelAdverRouteListEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1 |
juniMplsGroupLdpLabelAdverRouteListNameThis LDP label advertisement route list name for which this entry contains information. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.1 |
juniMplsGroupLdpLabelAdverNbrListNameThe LDP label advertisement neighbor route list name for which this entry contains information. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.2 |
juniMplsGroupLabelAdverListModeThis object selects the mode of addition/deletion to the list.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.3 |
juniMplsGroupLdpProfileTableTable is a list of LDP Profile entries. SEQUENCE OF JuniMplsGroupLdpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.4 |
juniMplsGroupLdpProfileEntryEach entry represents one LDP profile settings. JuniMplsGroupLdpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1 |
juniMplsGroupLdpProfileNameLDP profile name identifies unique entry in the table. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.1 |
juniMplsGroupLdpProfileHelloHoldTimeConfigure the LDP peers hello hold time period.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.2 |
juniMplsGroupLdpProfileCrLdpAdminStateEnable or disable the constraint-based routing label distribution protocol (CR-LDP) admin state.rwobsolete Enumeration .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.3 |
juniMplsGroupLdpProfileRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsGroupLdpProfileCrLdpAdminState juniMplsGroupLdpProfileRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.4 |
juniMplsGroupRsvpProfileTableTable is a list of LDP Profile entries. SEQUENCE OF JuniMplsGroupRsvpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.5 |
juniMplsGroupRsvpProfileEntryEach entry represents one LDP profile settings. JuniMplsGroupRsvpProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1 |
juniMplsGroupRsvpProfileNameThe RSVP profile name identifies unique entry in the table. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.1 |
juniMplsGroupRsvpProfileRefreshPeriodConfigure the time out period between the generation of two refresh messages.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.2 |
juniMplsGroupRsvpProfileCleanupTimeoutFactorConfgure the number of refresh messages can be lost before PATH or RESV state is ended.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.3 |
juniMplsGroupRsvpProfileRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: juniMplsGroupRsvpProfileRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.4 |
juniMplsMajorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.2 |
juniMplsIfMajorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.2.1 |
juniMplsIfMajorNextIfIndexCoordinate ifIndex value allocation for entries in the juniMplsIfMajorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.ro JuniNextIfIndex (Juniper-TC) .1.3.6.1.4.1.4874.2.2.54.1.2.1.1 |
juniMplsIfMajorTableThis table contains entries for MPLS Major interfaces present in the system. SEQUENCE OF JuniMplsIfMajorEntry .1.3.6.1.4.1.4874.2.2.54.1.2.1.2 |
juniMplsIfMajorEntryEach entry describes the characteristics of an MPLS Major interface. Creating/deleting entries in this table causes corresponding entries to be created/deleted in ifTable/ifXTable/juniIfTable. JuniMplsIfMajorEntry .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1 |
juniMplsIfMajorIndexThe ifIndex of the MPLS Major interface. When creating entries in this table, suitable values for this object are determined by reading juniMplsIfMajorNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.1 |
juniMplsIfMajorRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMajorRowStatus juniMplsIfMajorLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniMplsIfMajorIndex must have been determined previously, by reading juniMplsIfMajorNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.2 |
juniMplsIfMajorLowerIfIndexThe ifIndex of an interface over which this MPLS Major interface to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.3 |
juniMplsIfMajorAdminStatusUse this object to create MPLS major interface stacked over any link layer interface. Lower layer(index) over which major stacks has to be specified for successful creation of the major interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.4 |
juniMplsIfMajorLdpAdminStatusThis object enables/disables LDP admin status on the MPLS interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.5 |
juniMplsIfMajorLdpProfileNameAll the LDP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the LDP profile name.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.6 |
juniMplsIfMajorLdpVpiStartThis object is defined to support configurations of interface label space. This configures the start range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the stop range cunncurrently.rw JuniMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.7 |
juniMplsIfMajorLdpVpiStopThis object is defined to support configurations of interface label space. This configures the stop range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the start range cunncurrently.rw JuniMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.8 |
juniMplsIfMajorLdpVciStartThis object is defined to support configurations of interface label space. This configures the start range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the stop range cunncurrently.rw JuniMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.9 |
juniMplsIfMajorLdpVciStopThis object is defined to support configurations of interface label space. This configures the stop range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the start range cunncurrently.rw JuniMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.10 |
juniMplsIfMajorRsvpAdminStatusThis object configures RSVP admin status for MPLS interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.11 |
juniMplsIfMajorRsvpProfileNameAll the RSVP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the RSVP profile name.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.12 |
juniMplsIfMajorRsvpVpiStartThis object is defined to support configurations of interface label space. This configures the start range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the stop range cunncurrently.rw JuniMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.13 |
juniMplsIfMajorRsvpVpiStopThis object is defined to support configurations of interface label space. This configures the stop range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the start range cunncurrently.rw JuniMajorCfgVpiRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.14 |
juniMplsIfMajorRsvpVciStartThis object is defined to support configurations of interface label space. This configures the start range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the stop range cunncurrently.rw JuniMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.15 |
juniMplsIfMajorRsvpVciStopThis object is defined to support configurations of interface label space. This configures the stop range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the start range cunncurrently.rw JuniMajorCfgVciRanges .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.16 |
juniMplsIfMajorLabelSpaceTypeDisplays the label space type for the MPLS interface.ro Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.17 |
juniMplsIfMajorOpStateThis object displays MPLS major interface operation state.ro Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.18 |
juniMplsIfMajorCrLdpAdminStateThis object displays the admin state of CR-LDP.roobsolete Enumeration .1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.19 |
juniMplsMinorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.3 |
juniMplsIfMinorLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.3.1 |
juniMplsIfMinorNextIfIndexCoordinates ifIndex value allocation for entries in the juniMplsIfMinorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.ro JuniNextIfIndex (Juniper-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.1 |
juniMplsIfMinorTableThis table contains entries for MPLS Minor interfaces present in the system. SEQUENCE OF JuniMplsIfMinorEntry .1.3.6.1.4.1.4874.2.2.54.1.3.1.2 |
juniMplsIfMinorEntryEach entry describes the characteristics of an MPLS Minor interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable. JuniMplsIfMinorEntry .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1 |
juniMplsIfMinorIndexThe ifIndex of the MPLS Minor interface. When creating entries in this table, suitable values for this object are determined by reading juniMplsMinorNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.1 |
juniMplsIfMinorRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create/delete an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMinorRowStatus juniMplsIfMinorTunnelName In addition, when creating an entry the following conditions must hold: A value for juniMplsIfMinorIndex must have been determined previously, by reading juniMplsMinorNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.2 |
juniMplsIfMinorLowerIfIndexThe ifIndex of an interface over which this MPLS Minor interface is to be layered. A value of zero indicates no layering. As minor interface can be created without stacking on major interface, as and when it stacks on major interface by signalling protocol, it's value can be read.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.3 |
juniMplsIfMinorAdminStatusWith this object minor interface admin status can be enabled/disabled.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.4 |
juniMplsIfMinorEndpointAddressThis object configures the IP address of the tunnel destination. This object can be set along with the juniMplsIfMinorEndpointDstMask to configure the tunnel destination mask, but it is optional.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.5 |
juniMplsIfMinorEndpointDstMaskThis object configures the tunnel destination mask. It can be set along with the juniMplsIfMinorEndpointAddress.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.6 |
juniMplsIfMinorTunnelMetricModeSelect the relative or absolute mode to configure the absolute or relative tunnel metric. To set the tunnel to relative metric, juniMplsIfMinorRelativeTunnelMetric has to be set along with this object option as relative. To set the tunnel to absolute metric, juniMplsIfMinorAbsoluteTunnelMetric has to be set along with this object option as absolute.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.7 |
juniMplsIfMinorAbsoluteTunnelMetricThis object allows configuration of absolute metric values. Refer to juniMplsIfMinorTunnelMetricMode for how set it.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.8 |
juniMplsIfMinorRelativeTunnelMetricThis object allows configuration of relative metric values. Refer to juniMplsIfMinorTunnelMetricMode for how set it.rw Integer32 (-10..10) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.9 |
juniMplsIfMinorLabelDistProtoThis object allows to select label distribution protocol. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.rwobsolete Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.10 |
juniMplsIfMinorAnnounceToOspfThis object allows to register LSP endpoints to OSPF to next hop calculation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.11 |
juniMplsIfMinorAnnounceToIsisThis object allows to register LSP endpoints to IS-IS for next hop calculation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.12 |
juniMplsIfMinorAnnounceToBgpThis object allows to register LSP endpoints to BGP for next hop calculation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.13 |
juniMplsIfMinorBandwidthThis object allows configuration of bandwidth requirements for the tunnel.rw JuniMinorCfgBWRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.14 |
juniMplsIfMinorAffinityThis object allows configuration of resource class affinity for the tunnel.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.15 |
juniMplsIfMinorAffinityMaskThis allows to set the resource class affinity mask. Since it is a mask, set along with the affinity for successful configurations.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.16 |
juniMplsIfMinorSetupPriorityThis object allows configuration of preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.rw JuniMinorCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.17 |
juniMplsIfMinorHoldingPriorityThis object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.rw JuniMinorCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.18 |
juniMplsIfMinorTunnelNameThis object allows configuration of the tunnel name to be associated with tunnel settings.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.19 |
juniMplsIfMinorTunnelRetryTimesThis object allows configuration of the number of retries for tunnel setup.rw JuniMinorCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.20 |
juniMplsIfMinorTunnelRetryIntervalThis object allows configuration of retry interval for tunnel setup.rw JuniMinorCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.21 |
juniMplsIfMinorTunnelRetryTimesNorouteThis object allows configuration of the tunnel retries when no route notifications are received.rw JuniMinorCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.22 |
juniMplsIfMinorTunnelRetryIntervalNorouteThis object allows configuration of the tunnel retry interval when no route notifications are received.rw JuniMinorCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.23 |
juniMplsIfMinorBaseTunnelNameThis object allows configuration of the base tunnel name over which all the tunnels are stacked over.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.24 |
juniMplsIfMinorVpnOuiNumberThis object allows configuration of the OUI part of VPN ID.rwobsolete Integer32 .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.25 |
juniMplsIfMinorVpnIndexThis object allows configuration of the index part of VPN ID.rwobsolete IpAddress .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.26 |
juniMplsIfMinorTunnelOpStateThis object displays the tunnel operation state. established : Tunnel established teNegotiation : TE Negotiation up : Tunnel Up down : Tunnel Down cfgChanged : Tunnel config changed cfgIncEn : Tunnel incomplete Config Admin State Enable cfgIncDis : Tunnel incomplete Config Admin State Disable disabled : Tunnel disabled rel : noChange : Tunnel state no changero Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.27 |
juniMplsIfMinorTargetedDynamicTunnelConfigure targeted dynamic tunnel.rwobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.28 |
juniMplsIfMinorReoptimizationConfigure tunnel reoptimization.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.29 |
juniMplsMinorLayerList OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.3.2 |
juniMplsIfMinorPathOptionTableTable is a list of different LSP paths as option for each LSP setup. SEQUENCE OF JuniMplsIfMinorPathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.3.2.1 |
juniMplsIfMinorPathOptionEntryEach entry represents one path option for the LSP. JuniMplsIfMinorPathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1 |
juniMplsIfMinorPathOptionIndexMinor interface unique ID. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.1 |
juniMplsIfMinorPathOptionNumberUnique number to identify each path option configured. Integer32 .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.2 |
juniMplsIfMinorPathOptionProtocolSelect the each path option explicit routing protocol.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.3 |
juniMplsIfMinorPathOptionLockdownEnable/disable each configured path option reoptimization.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.4 |
juniMplsIfMinorPathOptionPathNameConfigure the name for each path option.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.5 |
juniMplsIfMinorPathOptionPathIdConfigure the path option ID. Either the name or ID will be associated with a path at a time. If the path name and ID are set at a same time for the path, the name will have precedence over ID.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.6 |
juniMplsIfMinorPathOptionRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMinorPathOptionRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.7 |
juniMplsTunnelProfile OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.4 |
juniMplsTunnelProfileGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.4.1 |
juniMplsTunnelProfileTableTable is a list of tunnel profiles for a given VR. SEQUENCE OF JuniMplsTunnelProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.4.1.1 |
juniMplsTunnelProfileEntryEach entry represents one tunnel profile. JuniMplsTunnelProfileEntry .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1 |
juniMplsTunnelProfileNameAssociate a name for the configured tunnel profile settings. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.1 |
juniMplsTunnelProfileAdminStatusEnable/disable the adminstatus of the tunnel profile.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.2 |
juniMplsTunnelProfileBaseTunnelNameConfigure the base tunnel name in tunnel profile settings. This base tunnel is the one over which all the other tunnels are stacked over. Configured base tunnel name in profile settings will be associated with the actual configured base tunnel name.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.3 |
juniMplsTunnelProfileIpProfileNameConfigures the name for IP profile settings for the IP interfaces over which MPLS tunnels are stacked.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.4 |
juniMplsTunnelProfileLabelDistProtoConfigure the label distribution protocol to associate with a tunnel profile. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.rwobsolete Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.5 |
juniMplsTunnelProfileAnnounceToOspfConfigure the routing protocol for next hop calculations as OSPF.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.6 |
juniMplsTunnelProfileAnnounceToIsisConfigure routing protocol for next hop calculations as ISIS.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.7 |
juniMplsTunnelProfileAnnounceToBgpConfigure routing protocol for next hop calculations as BGP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.8 |
juniMplsTunnelProfileMetricModeSelect the relative or absolute mode to configure the absolute or relative tunnel profile metric. To set the tunnel profile to relative metric, juniMplsTunnelProfileRelativeMetric has to be set along with this object option as relative. To set the tunnel profile to absolute metric, juniMplsTunnelProfileAbsoluteMetric has to be set along with this object option as absolute.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.9 |
juniMplsTunnelProfileAbsoluteMetricThis object allows configuration of the absolute metric values. Refer to juniMplsTunnelProfileMetricMode for how set it.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.10 |
juniMplsTunnelProfileRelativeMetricThis object allows configuration of the relative metric values. Refer to juniMplsTunnelProfileMetricMode for how set it.rw Integer32 (-10..10) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.11 |
juniMplsTunnelProfileBandwidthThis object allows configuration of bandwidth requirements for the tunnel.rw JuniProfileCfgBWRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.12 |
juniMplsTunnelProfileAffinityThis object allows configuration of the resource class affinity for the tunnel. This can set independently of juniMplsTunnelProfileAffinityMask.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.13 |
juniMplsTunnelProfileAffinityMaskThis allows configuration of which bits in the affinity must match the resource class bits. Can't be set independently; always with juniMplsTunnelProfileAffinity. Specify the value in bit mask format.rw OCTET STRING .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.14 |
juniMplsTunnelProfileSetupPriorityThis object configuration of the preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.rw JuniProfileCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.15 |
juniMplsTunnelProfileHoldingPriorityThis object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.rw JuniProfileCfgHoldingAndSetupPriorityRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.16 |
juniMplsTunnelProfileRetryTimesThis object allows configuration of the number of retries for the tunnel setup.rw JuniProfileCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.17 |
juniMplsTunnelProfileRetryIntervalThis object allows configuration of retry interval for tunnel setup.rw JuniProfileCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.18 |
juniMplsTunnelProfileRetryTimesNorouteThis object allows configuration of the tunnel retries when no route notifications are received.rw JuniProfileCfgRetryTimesAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.19 |
juniMplsTunnelProfileRetryIntervalNorouteThis object allows configuration of the tunnel retry interval when no route notifications are received.rw JuniProfileCfgRetryIntervalAndNorouteRanges .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.20 |
juniMplsTunnelProfileVpnOuiNumberThis object allows configuration of the OUI part of VPN ID.rwobsolete Integer32 .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.21 |
juniMplsTunnelProfileVpnIndexThis object allows configuration of the index part of VPN ID.rwobsolete IpAddress .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.22 |
juniMplsTunnelProfileRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfileRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.23 |
juniMplsTunnelProfileTargetedDynamicTunnelConfigure targeted dynamic tunnel.rwobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.24 |
juniMplsTunnelProfileList OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.4.2 |
juniMplsTunnelProfilePathOptionTableTable is a list of different LSP paths as option for each LSP setup, configured as part of tunnel profile settings SEQUENCE OF JuniMplsTunnelProfilePathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.1 |
juniMplsTunnelProfilePathOptionEntryEach entry represents one path option for the LSP setup, configured as a part of tunnel profile settings. JuniMplsTunnelProfilePathOptionEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1 |
juniMplsTunnelProfileNamePathOptionName of the path option. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.1 |
juniMplsTunnelProfilePathOptionNumberUnique identifier for the path option. Integer32 .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.2 |
juniMplsTunnelProfilePathOptionProtocolPath selection option protocol.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.3 |
juniMplsTunnelProfilePathOptionLockdownEnable/disable path selection option reoptimization.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.4 |
juniMplsTunnelProfilePathOptionPathNameAssociate a name with each explicit path.rw DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.5 |
juniMplsTunnelProfilePathOptionPathIdEach explicit path can be associated either name or ID. This object allows configuration of the ID for the explicit path.rw Integer32 .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.6 |
juniMplsTunnelProfilePathOptionRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfilePathOptionRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.7 |
juniMplsTunnelProfileDynamicEndpointTableThis table contains entries for the dynamic endpoints configured for each tunnel profile. SEQUENCE OF JuniMplsTunnelProfileDynamicEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.2 |
juniMplsTunnelProfileDynamicEndpointEntryDynamic endpoint entries for each tunnel profile. JuniMplsTunnelProfileDynamicEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1 |
juniMplsTunnelProfileNameDynamicEndpointConfigure the tunnel dynamic endpoint in tunnel profile settings. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.1 |
juniMplsTunnelProfileDynamicEndpointTypeConfigure the dynamic endpoint type for the tunnel. Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.2 |
juniMplsTunnelProfileDynamicEndpointPolicyListTypeThis object allows configuration of the dynamic tunnel policy type selection. Enumeration .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.3 |
juniMplsTunnelProfileDynamicEndpointListNameThis object allows configuration of the dynamic endpoints access list name. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.4 |
juniMplsTunnelProfileDynamicEndpointRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: juniMplsTunnelProfileDynamicEndpointRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.5 |
juniMplsTunnelProfileTunnelEndpointTableTable contains list of tunnel static enpoints configured for each tunnel profile. SEQUENCE OF JuniMplsTunnelProfileTunnelEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.3 |
juniMplsTunnelProfileTunnelEndpointEntryEach entry represents one static endpoint configuration for the tunnel. JuniMplsTunnelProfileTunnelEndpointEntry .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1 |
juniMplsTunnelProfileNameTunnelEndpointThis object configures the tunnel profile name. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.1 |
juniMplsTunnelProfileTunnelEndpointAddressThis object configures the IP address of the tunnel destination. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.2 |
juniMplsTunnelProfileTunnelEndpointDstMaskThis object configures the tunnel destination mask. A value of 255.255.255.255 is expected. IpAddress .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.3 |
juniMplsTunnelProfileTunnelEndpointRowStatusControls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfileTunnelEndpointRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.4 |
juniMplsExplicitPath OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.5 |
juniMplsExplicitPathGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.1.5.1 |
juniMplsExplicitPathTableTable is a list of hops configurations for explicit paths. SEQUENCE OF JuniMplsExplicitPathEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.1 |
juniMplsExplicitPathEntryEach entry represents one hop configuration for the particular explicit path. JuniMplsExplicitPathEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1 |
juniMplsExplicitPathNameConfigure the name for the explicit path used as table index. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.1 |
juniMplsExplicitPathAdminStateEnable/disable explicit path adminstatus.rw Enumeration .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.2 |
juniMplsExplicitPathRowStatusCreation/deletion of the explicit path is done through setting this object.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.3 |
juniMplsExplicitPathNodeTableTable is a list of configured explicit paths. SEQUENCE OF JuniMplsExplicitPathNodeEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.2 |
juniMplsExplicitPathNodeEntryEach entry represents one hop in a particular explicit path. JuniMplsExplicitPathNodeEntry .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1 |
juniMplsExplicitPathNodeNameConfigure the name for the explicit path used in the table index. DisplayString .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.1 |
juniMplsExplicitPathNodeIndexNumberEach explicit path hop will have an index associated with it. Configure each path hop index using this object. Integer32 .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.2 |
juniMplsExplicitPathNodeLooseConfigure the explicit path hop as strict or loose. Set along with HopAddress.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.3 |
juniMplsExplicitPathNodeHopAddressConfigure the hop IP address to setup explicit path. Explicit path next hop will be created when the mentioned hop IP address doesn't belong to any of the existing hop even without setting the rowStatus createAndGo value. The rowStatus value is used to destroy the node.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.4 |
juniMplsExplicitPathNodeHopAddressMaskConfigure the hop IP address mask. Set along with hop address.rw IpAddress .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.5 |
juniMplsExplicitPathNodeRowStatusUse this object for deletion of the node. For node creation, this value have no effect. Setting the node with IP address create the node. To delete the node set only this object.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.6 |
juniMplsConformance OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.2 |
juniMplsCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.2.1 |
juniMplsComplianceObsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement became obsolete when RowStatus support was added to some of the minor layer and tunnel profile tables.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.1.1 |
juniMplsCompliance2Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement became obsolete when the juniMplsGroupIpTtlPropagate object was added to the juniMplsGroup scalar group.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.1.2 |
juniMplsCompliance3Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement become obsolete when the objects juniMplsIfMajorCrLdpAdminState, juniMplsIfMinorLabelDistProto, juniMplsIfMinorBaseTunnelName, juniMplsIfMinorVpnOuiNumber, juniMplsIfMinorVpnIndex, juniMplsIfMinorTargetedDynamicTunnel, juniMplsTunnelProfileBaseTunnelName, juniMplsTunnelProfileLabelDistProto, juniMplsTunnelProfileVpnOuiNumber, juniMplsTunnelProfileVpnIndex, juniMplsTunnelProfileTargetedDynamicTunnel, juniMplsGroupLdpRetryTimesNoroute, juniMplsGroupLdpRetryTimes, juniMplsGroupLdpRetryIntervalNoroute and juniMplsGroupLdpProfileCrLdpAdminState became obsolete.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.1.3 |
juniMplsCompliance4The compliance statement for entities which implement the Juniper MPLS MIB. Unknown .1.3.6.1.4.1.4874.2.2.54.2.1.4 |
juniMplsConfGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.54.2.2 |
juniMplsLsrGlobalConfGroupObsolete collection of objects providing management of MPLS global configurations in a Juniper product. This group became obsolete when the object juniMplsGroupIpTtlPropagate was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.1 |
juniMplsMajorLayerConfGroupA collection of objects providing management of major MPLS interfaces in a Juniper product. This group became obsolete when the object juniMplsIfMajorCrLdpAdminState became obsolete.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.2 |
juniMplsMinorLayerConfGroupObsolete collection of objects providing management of minor MPLS (tunnel) in a Juniper product. This group became obsolete when the juniMplsIfMinorPathOptionRowStatus object was added.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.3 |
juniMplsTunnelProfileConfGroupObsolete collection of objects providing management of MPLS tunnel profiles in a Juniper product. This group became obsolete when RowStatus objects were added to some of the tables.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.4 |
juniMplsExplicitPathConfGroupA collection of objects providing management of MPLS explicit paths in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.5 |
juniMplsMinorLayerConfGroup2A collection of objects providing management of minor MPLS (tunnel) interfaces in a Juniper product. This group became obsolete when the objects juniMplsIfMinorLabelDistProto, juniMplsIfMinorBaseTunnelName, juniMplsIfMinorVpnOuiNumber, juniMplsIfMinorVpnIndex, juniMplsIfMinorTargetedDynamicTunnel became obsolete.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.6 |
juniMplsTunnelProfileConfGroup2A collection of objects providing management of MPLS tunnel profiles in a Juniper product. This group became oboslete when the objects juniMplsTunnelProfileBaseTunnelName, juniMplsTunnelProfileLabelDistProto, juniMplsTunnelProfileVpnOuiNumber, juniMplsTunnelProfileVpnIndex, juniMplsTunnelProfileTargetedDynamicTunnel became obsolete.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.7 |
juniMplsLsrGlobalConfGroup2A collection of objects providing management of MPLS label switching routers (LSRs) in a Juniper product. This group became obsolete when the object juniMplsGroupLdpRetryTimesNoroute, juniMplsGroupLdpRetryIntervalNoroute, juniMplsGroupLdpRetryTimes and juniMplsGroupLdpProfileCrLdpAdminState became obsolete.obsolete Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.8 |
juniMplsLsrGlobalConfGroup3A collection of objects providing management of MPLS label switching routers (LSRs) in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.9 |
juniMplsMajorLayerConfGroup2A collection of objects providing management of major MPLS interfaces in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.10 |
juniMplsMinorLayerConfGroup3A collection of objects providing management of minor MPLS (tunnel) interfaces in a Juniper product. Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.11 |
juniMplsTunnelProfileConfGroup3A collection of objects providing management of MPLS tunnel profiles in a Juniper product Unknown .1.3.6.1.4.1.4874.2.2.54.2.2.12 |