JUNIPER-SOAM-PM-MIB
Updated May 31, 2016AI MIB Summary
The JUNIPER-SOAM-PM-MIB enables SNMP-based monitoring of Ethernet Services Operations, Administration, and Maintenance (OAM) performance metrics on Juniper Networks devices, specifically tracking packet loss, delay, and jitter statistics for active service flows.
This MIB module contains the management objects for the management of Ethernet Services Operations, Administration and Maintenance for Performance Monitoring.
Main OID:
jnxSoamPmMib.1.3.6.1.4.1.2636.3.78
285
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
285 total| Object Name |
|---|
jnxSoamPmMibThis MIB module contains the management objects for the
management of Ethernet Services Operations, Administration
and Maintenance for Performance Monitoring. MODULE-IDENTITY .1.3.6.1.4.1.2636.3.78 |
jnxSoamPmNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.0 |
jnxSoamLmSessionStartStopAlarmAn jnxSoamLmSessionStartStopAlarm notification is sent when the state of
jnxSoamLmCfgSessionStatus changes.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the individual PM session reporting the start/stop
by the indices in the OID jnxSoamLmCfgSessionStatus, including
dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, and
jnxSoamLmCfgIndex.
An agent is not to generate more than one jnxSoamLmSessionStartStopAlarm
'notification-event' in a given time interval per LM session as specified
by the jnxSoamPmNotificationCfgAlarmInterval. A 'notification-event' is
the transmission of a single notification to a list of notification
destinations.
If additional operational state changes occur within the
jnxSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are be suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any operational
state changes occurred since the start of the alarm interval period. In
such a case, another alarm interval period is started right away. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.78.0.1 |
jnxSoamDmSessionStartStopAlarmAn jnxSoamDmSessionStartStopAlarm notification is sent when the state of
jnxSoamDmCfgSessionStatus changes.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the individual PM session reporting the start/stop
by the indices in the OID jnxSoamDmCfgSessionStatus, including
dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, and
jnxSoamDmCfgIndex.
An agent is not to generate more than one jnxSoamDmSessionStartStopAlarm
'notification-event' in a given time interval per DM session as specified
by jnxSoamPmNotificationCfgAlarmInterval. A 'notification-event' is the
transmission of a single notification to a list of notification
destinations.
If additional operational state changes occur within the
jnxSoamPmNotificationCfgAlarmInterval period, then notification generation
for these changes are suppressed by the agent until the current alarm
interval expires. At the end of an alarm interval period, one
notification-event is generated if any operational state changes
occurred since the start of the alarm interval period. In such a case,
another alarm interval period is started right away. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.78.0.2 |
jnxSoamPmThresholdCrossingAlarmAn jnxSoamPmThresholdCrossingAlarm notification is sent if the
following conditions are met for a particular type.
For an aboveAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdAboveAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdAboveAlarm; and
e) no previous jnxSoamPmThresholdCrossingAlarm notifications with type
aboveAlarm have been sent relating to the same threshold in the
jnxSoamLmThresholdCfgTable or jnxSoamDmThresholdCfgTable and the
same parameter, during this Measurement Interval.
For a setAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did not
exceed the value configured in the jnxSoamLmThresholdCfgTable for
a LM crossing entry or jnxSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
For a clearAlarm five conditions need to be met:
a) measurement of the parameter is enabled via jnxSoamLmCfgMeasurementEnable
for a LM crossing or jnxSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the jnxSoamLmThresholdCfgTable
or jnxSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter did not exceed the value configured
in the jnxSoamLmThresholdCfgTable for a LM crossing entry or
jnxSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did
exceed the value configured in the jnxSoamLmThresholdCfgTable for
a LM crossing entry or jnxSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
In the case of thresholds applied to a maximum or average measurement
counter, the previous measured value is the value of the counter at the
end of the preceding Measurement Interval. In the case of thresholds
applied to the last measured value, it is the previous measured value.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the LM or DM session reporting the threshold
crossing by the indices in the jnxSoamPmNotificationCfgThresholdId object,
including dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier,
and the jnxSoamLmCfgIndex or jnxSoamDmCfgIndex.
An agent is not to generate more than one jnxSoamLmThresholdCrossingAlarm
'notification-event' of a given type per LM or DM session as specified
by jnxSoamPmNotificationCfgAlarmInterval. A 'notification-event' is the
transmission of a single notification to a list of notification
destinations.
If additional threshold crossing events occur within the
jnxSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any threshold
crossing events occurred since the start of the alarm interval period.
In such a case, another alarm interval period is started right away. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.78.0.3 |
jnxSoamPmThresholdFlapAlarmThe jnxSoamPmThresholdFlapAlarm is sent when the CFM Threshold Flap
Notification feature is enabled which would dampen the
jnxSoamPmThresholdCrossingAlarm sent to NMS. The jnxSoamPmThresholdFlapAlarm
gives details about Flaps occured during the time interval. The
jnxSoamPmThresholdFlapAlarm is sent for the follwing below conditions
a) Trap is sent if one flap sequence has occured
b) Trap is sent if threshold or timer changes happens.
c) Trap is sent when finite iterations counts expires. NOTIFICATION-TYPE .1.3.6.1.4.1.2636.3.78.0.4 |
jnxSoamPmMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.1 |
jnxSoamPmMep OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.1.1 |
jnxSoamPmMepTableThis table is an extension of the dot1agCfmMepTable and rows
are automatically added or deleted from this table based upon row
creation and destruction of the dot1agCfmMepTable.
This table represents the local MEP PM configuration table. The
primary purpose of this table is provide local parameters for the
SOAM PM function found in [Y.1731] and [MEF SOAM-PM] and instantiated
at a MEP. SEQUENCE OF JnxSoamPmMepEntry .1.3.6.1.4.1.2636.3.78.1.1.1 |
jnxSoamPmMepEntryThe conceptual row of jnxSoamPmMepTable. JnxSoamPmMepEntry .1.3.6.1.4.1.2636.3.78.1.1.1.1 |
jnxSoamPmMepOperNextIndexThis object contains an unused value for a PM session number on a
MEP that can be used for either LM or DM sessions, or a zero to
indicate that none exist. This value needs to be read in order to
find an available index for row-creation of a PM session on a MEP and
then used when a row is created. This value is automatically updated
by the SNMP Agent after the row is created.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never to be reused for other PM sessions on the same MEP while this
session is active, or until it wraps to zero. The index value keeps
increasing up to that time. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused.
This object is an extension of the dot1agCfmMepTable and the object is
automatically added or deleted based upon row creation and destruction
of the dot1agCfmMepTable.ro Dot1afCfmIndexIntegerNextFree (IEEE8021-CFM-MIB) .1.3.6.1.4.1.2636.3.78.1.1.1.1.1 |
jnxSoamPmMepLmSingleEndedResponderThis object specifies whether the Loss Measurement (LMM) single-ended
Responder is enabled.
The value 'true' indicates the single-ended Loss Measurement Responder
is enabled and if a LMM message is received a LMR will be sent in reply.
The value 'false' indicates the single-ended Loss Measurement Responder
is disabled. If a LMM message is received no response will be sent and
the message will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.1.1.1.2 |
jnxSoamPmMepSlmSingleEndedResponderThis object specifies whether the Synthetic Loss Measurement (SLM)
single-ended Responder is enabled.
The value 'true' indicates the single-ended SLM Responder is enabled and
if a SLM message is received a SLR will be sent in reply.
The value 'false' indicates the single-ended SLM Responder is disabled.
If a SLM message is received no response will be sent and the message
will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.1.1.1.3 |
jnxSoamPmMepDmSingleEndedResponderThis object specifies whether the Delay Measurement (DMM) single
ended Responder is enabled.
The value 'true' indicates the single-ended Delay Measurement Responder
is enabled and if a DMM message is received a DMR will be sent in reply.
The value 'false' indicates the single-ended Delay Measurement Responder
is disabled. If a DMM message is received no response will be sent and
the message will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.1.1.1.4 |
jnxSoamPmLmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.1.2 |
jnxSoamLmCfgTableThis table includes configuration objects and operations for the
Frame Loss Measurement function defined in [Y.1731] and [MEF SOAM-PM].
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP. A
Loss Measurement session is created on an existing MEP by first
accessing the jnxSoamPmMepOperNextIndex object and using this value as
the jnxSoamLmCfgIndex in the row creation.
Some writable objects in this table are only applicable in certain cases
(as described under each object), and attempts to write values for them
in other cases will be ignored.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamLmCfgEntry .1.3.6.1.4.1.2636.3.78.1.2.1 |
jnxSoamLmCfgEntryThe conceptual row of jnxSoamLmCfgTable. JnxSoamLmCfgEntry .1.3.6.1.4.1.2636.3.78.1.2.1.1 |
jnxSoamLmCfgIndexAn index to the Loss Measurement Configuration table which indicates
the specific measurement session for the MEP.
jnxSoamPmMepOperNextIndex needs to be inspected to find an
available index for row-creation.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused for other PM sessions on the same MEP while this
session is active. The index value keeps increasing until it
wraps to 0. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.1 |
jnxSoamLmCfgTypeThis object specifies what type of Loss Measurement
will be performed.
lmLmm(1) LMM SOAM PDU generated and received LMR responses tracked
lmSlm(2) SLM SOAM PDU generated and received SLR responses tracked
lmCcm(3) CCM SOAM PDU generated and received CCM PDUs tracked
The lmSlm value is required. The lmLmm and lmCcm values are optional.
The lmCcm loss measurement values are only valid for a point-to-point
MEG. Multipoint MEGs may give unreliable loss measurements.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Enumeration .1.3.6.1.4.1.2636.3.78.1.2.1.1.2 |
jnxSoamLmCfgVersionThis object indicates the version of the PDUs used to perform
Loss Measurement.
The value is placed in the Version field of the PDU and indicates
that the PDU format used is the format defined in Y.1731 with
that version.
The exact PDUs to use are specified by this object in combination with
jnxSoamLmCfgType.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.3 |
jnxSoamLmCfgEnabledThis object specifies whether the Loss Measurement session
is enabled.
The value 'true' indicates the Loss Measurement session is enabled and
SOAM PDUs are sent and/or measurements are collected when the session
is running according to the scheduling objects (start time, stop time,
etc.).
The value 'false' indicates the Loss Measurement session is disabled
and SOAM PDUs are not sent and/or measurements collected.
For a Loss Measurement session to be removed the row is
deleted in order to release internal resources.
This object can written/modified after row creation time.
If the LM session is enabled it resumes after shutdown/restart.
If the LM session is disabled the current Measurement Interval is
stopped, if it in process at the time, and all the in process calculations
for the partially completed Measurement Interval are finalized.
This object does not affect whether the single-ended Responder is
enabled or not, which is enabled or disabled by the
jnxSoamPmMepLmSingleEndedResponder and
jnxSoamPmMepSlmSingleEndedResponder objects.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.4 |
jnxSoamLmCfgMeasurementEnableA vector of bits that indicates the type of SOAM LM counters found
in the jnxSoamLmMeasuredStatsTable, jnxSoamLmCurrentStatsTable,
jnxSoamLmHistoryStatsTable that are enabled.
that are enabled.
A bit set to '1' enables the specific SOAM LM counter. A bit set to
'0' disables the SOAM LM counter.
If a particular SOAM LM counter is not supported the BIT value is
set to '0'.
Not all SOAM LM counters are supported for all SOAM LM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bForwardTransmitedFrames (0)
Enables/disables the jnxSoamLmCurrentStatsForwardTransmittedFrames
and jnxSoamLmHistoryStatsForwardTransmittedFrames counters.
bForwardReceivedFrames(1)
Enables/disables the jnxSoamLmCurrentStatsForwardReceivedFrames
and jnxSoamLmHistoryStatsForwardReceivedFrames counters.
bForwardMinFlr(2)
Enables/disables the jnxSoamLmCurrentStatsForwardMinFlr
and jnxSoamLmHistoryStatsForwardMinFlr counters.
bForwardMaxFlr(3)
Enables/disables the jnxSoamLmCurrentStatsForwardMaxFlr
and jnxSoamLmHistoryStatsForwardMaxFlr counters.
bForwardAvgFlr(4)
Enables/disables the jnxSoamLmCurrentStatsForwardAvgFlr
and jnxSoamLmHistoryStatsForwardAvgFlr counters.
bBackwardTransmitedFrames(5)
Enables/disables the jnxSoamLmCurrentStatsBackwardTransmittedFrames
and jnxSoamLmHistoryStatsBackwardTransmittedFrames counters.
bBackwardReceivedFrames(6)
Enables/disables the jnxSoamLmCurrentStatsBackwardReceivedFrames
and jnxSoamLmHistoryStatsBackwardReceivedFrames counters.
bBackwardMinFlr(7)
Enables/disables the jnxSoamLmCurrentStatsBackwardMinFlr
and jnxSoamLmHistoryStatsBackwardMinFlr counters.
bBackwardMaxFlr(8)
Enables/disables the jnxSoamLmCurrentStatsBackwardMaxFlr
and jnxSoamLmHistoryStatsBackwardMaxFlr counters.
bBackwardAvgFlr(9)
Enables/disables the jnxSoamLmCurrentStatsBackwardAvgFlr
and jnxSoamLmHistoryStatsBackwardAvgFlr counters.
bSoamPdusSent (10)
Enables/disables the jnxSoamLmCurrentStatsSoamPdusSent
and jnxSoamLmHistoryStatsSoamPdusSent counters.
bSoamPdusReceivedbReceivedMeasurements (11)
Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived
and jnxSoamLmHistoryStatsSoamPdusReceived counters.
bAvailForwardHighLoss(12)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardHighLoss
and jnxSoamLmHistoryAvailStatsForwardHighLoss counters.
bAvailForwardConsecutiveHighLoss(13)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLoss
and jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss counters.
bAvailForwardAvailable(14)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvailable
and jnxSoamLmHistoryAvailStatsForwardAvailable counters.
bAvailForwardUnavailable(15)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardUnavailable
and jnxSoamLmHistoryAvailStatsForwardUnavailable counters.
bAvailForwardMinFlr(16)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardMinFlr
and jnxSoamLmHistoryAvailStatsForwardMinFlr counters.
bAvailForwardMaxFlr(17)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardMaxFlr
and jnxSoamLmHistoryAvailStatsForwardMaxFlr counters.
bAvailForwardAvgFlr(18)
Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvgFlr
and jnxSoamLmHistoryAvailStatsForwardAvgFlr counters.
bAvailBackwardHighLoss(19)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardHighLoss
and jnxSoamLmHistoryAvailStatsBackwardHighLoss counters.
bAvailBackwardConsecutiveHighLoss(20)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss
and jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss counters.
bAvailBackwardAvailable(21)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvailable
and jnxSoamLmHistoryAvailStatsBackwardAvailable counters.
bAvailBackwardUnavailable(22)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardUnavailable
and jnxSoamLmHistoryAvailStatsBackwardUnavailable counters.
bAvailBackwardMinFlr(23)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMinFlr
and jnxSoamLmHistoryAvailStatsBackwardMinFlr counters.
bAvailBackwardMaxFlr(24)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMaxFlr
and jnxSoamLmHistoryAvailStatsBackwardMaxFlr counters.
bAvailBackwardAvgFlr(25)
Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvgFlr
and jnxSoamLmHistoryAvailStatsBackwardAvgFlr counters.
Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived
and jnxSoamLmHistoryStatsSoamPdusReceived counters.
bMeasuredStatsForwardMeasuredFlr(26)
Enables/disables the jnxSoamLmMeasuredStatsForwardFlr counter.
bMeasuredStatsBackwardMeasuredFlr(27)
Enables/disables the jnxSoamLmMeasuredStatsBackwardFlr counter.
bMeasuredStatsAvailForwardStatus(28)
Enables/disables the jnxSoamLmMeasuredStatsAvailForwardStatus counter.
bMeasuredStatsAvailBackwardStatus(29)
Enables/disables the jnxSoamLmMeasuredStatsAvailBackwardStatus counter.ro Bits .1.3.6.1.4.1.2636.3.78.1.2.1.1.5 |
jnxSoamLmCfgMessagePeriodThis object specifies the interval between Loss Measurement
OAM message transmission. For Loss Measurement monitoring
applications the default value is 1 sec.
This object is not applicable if jnxSoamLmCfgType is set to lmCcm
and is ignored for that Loss Measurement Type.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Integer32 UNITS "ms" .1.3.6.1.4.1.2636.3.78.1.2.1.1.6 |
jnxSoamLmCfgPriorityThis object specifies the Loss Measurement OAM message priority
as well as the priority of the service/OAM traffic to be monitored.
Only frames of the same Class of Service are counted.
The default value is to be the value which yields the lowest frame
loss.
This object is not applicable if jnxSoamLmCfgType is set to lmCcm.
This object can only be written at row creation time and cannot be
modified once it has been created.ro IEEE8021PriorityValue (IEEE8021-TC-MIB) .1.3.6.1.4.1.2636.3.78.1.2.1.1.7 |
jnxSoamLmCfgFrameSizeThis object specifies the Loss Measurement frame size between
64 bytes and the maximum transmission unit of the EVC.
The range of frame sizes from 64 through 2000 octets need to be
supported, and the range of frame sizes from 2001 through 9600 octets
is suggested be supported.
The adjustment to the frame size of the standard frame size is
accomplished by the addition of a Data or Test TLV. A Data or Test TLV
is only added to the frame if the frame size is greater than 64 bytes.
This object is only valid for the entity transmitting the Loss
Measurement frames, type 'lmSlm', and is ignored by the
entity receiving frames. It is not applicable for the 'lmCcm' or
'lmLmm' types.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.8 |
jnxSoamLmCfgDataPatternThis object specifies the LM data pattern included in a Data TLV
when the size of the LM frame is determined by the
jnxSoamLmFrameSize object and jnxoamLmTestTlvIncluded is 'false'.
If the frame size object does not define the LM frame size or
jnxSoamLmTestTlvIncluded is 'true' the value of this object is
ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro JnxSoamTcDataPatternType .1.3.6.1.4.1.2636.3.78.1.2.1.1.9 |
jnxSoamLmCfgTestTlvIncludedIndicates whether a Test TLV or Data TLV is included when the size
of the LM frame is determined by the jnxSoamLmFrameSize object.
A value of 'true' indicates that the Test TLV is to be included. A
value of 'false' indicates that the Data TLV is to be included.
If the frame size object does not define the LM frame size
the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.10 |
jnxSoamLmCfgTestTlvPatternThis object specifies the type of test pattern to be
sent in the LM frame Test TLV when the size of LM PDU is
determined by the jnxSoamLmFrameSize object and
jnxSoamLmTestTlvIncluded is 'true'. If the frame size object
does not define the LM frame size or jnxSoamLmTestTlvIncluded
is 'false' the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro JnxSoamTcTestPatternType .1.3.6.1.4.1.2636.3.78.1.2.1.1.11 |
jnxSoamLmCfgNumIntervalsStoredThis object specifies the number of completed Measurement Intervals
to store in the history statistic table (jnxSoamLmHistoryStatsTable)
At least 32 completed Measurement Intervals need to be stored. 96
Measurement Intervals are recommended to be stored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.12 |
jnxSoamLmCfgDestMepIdThe Maintenance Association End Point Identifier of
another MEP in the same Maintenance Association to which
the SOAM LM frame is to be sent.
This address will be used if the value of the column
jnxSoamLmDestIsMepId is 'true'. A value of zero
means that the destination MEP ID has not been configured.
This object is only valid for the entity transmitting the Loss
Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for
the 'lmCcm' type.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Dot1agCfmMepIdOrZero .1.3.6.1.4.1.2636.3.78.1.2.1.1.13 |
jnxSoamLmCfgDestIsMepIdA value of 'true' indicates that MEPID of the target MEP is used for
SOAM LM frame transmission.
A value of 'false' indicates that the MAC address of the
target MEP is used for SOAM LM frame transmission.
This object is only valid for the entity transmitting the Loss
Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for
the 'lmCcm' type.
This object can only be written at row creation time and cannot be
modified once it has been created.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.14 |
jnxSoamLmCfgStartTimeTypeThis object specifies the type of start time of the SOAM LM
session. The start time can be disabled (none), immediate, relative,
or fixed.
The value of 'none' is illegal and a write error will be returned
if this value is used.
The value of 'immediate' starts the SOAM LM session when the
jnxSoamLmCfgEnabled is true.
The value of 'fixed' starts the SOAM LM session when the
jnxSoamLmFixedStartDateAndTime is less than or equal to the current
system date and time and jnxSoamLmCfgEnabled is true. This value is used
to implement an On-Demand fixed time PM session.
The value of 'relative' starts the SOAM LM session when the current
system date and time minus the jnxSoamLmRelativeStartTime is greater
than or equal to the system date and time when the jnxSoamLmStartTimeType
object was written and jnxSoamLmCfgEnabled is true. This value is used
to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.ro JnxSoamTcOperationTimeType .1.3.6.1.4.1.2636.3.78.1.2.1.1.15 |
jnxSoamLmCfgFixedStartDateAndTimeThis object specifies the fixed start date/time for the
SOAM Loss Measurement session. This object is used only used if
jnxSoamLmStartTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.16 |
jnxSoamLmCfgRelativeStartTimeThis object specifies the relative start time, from the
current system time, for the SOAM LM session. This
object is used only if jnxSoamLmStartTimeType is 'relative' and is
ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.17 |
jnxSoamLmCfgRepetitionTimeThis object specifies a configurable repetition time between
Measurement Intervals in a Loss Measurement session, in seconds.
If the value is 0 (none), there is no time gap between the end of one
Measurement Interval and the start of a new Measurement Interval.
This is the normal usage case.
If the value is greater than 0 but less than or equal to the measurement
interval, an error is returned.
If the value is greater than one Measurement Interval there is time gap
between the end of one Measurement Interval and the start of the next
Measurement Interval. The repetition time specifies the time between
the start of consecutive Measurement Intervals; hence the gap between
the end of one Measurement Interval and the start of the next is equal
to the difference between the repetition time and the measurement
interval. During this gap, no SOAM PDUs are sent for this session and
no measurements are made.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.18 |
jnxSoamLmCfgAlignMeasurementIntervalsThis object specifies whether the Measurement Intervals for
the Loss Measurement session are aligned with a zero offset to
real time.
The value 'true' indicates that each Measurement Interval starts
at a time which is aligned to NE time source hour, if the repetition
time (or the Measurement Interval, if the repetition time is 0) is
a factor of an hour, i.e. 60min/15min = 4. For instance, a
Measurement Interval/repetition time of 15 minutes would stop/start
the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A
Measurement Interval/Repetition Time of 7 minutes would not align
to the hour since 7 minutes is NOT a factor of an hour, i.e.
60min/7min = 8.6. In this case the behavior is the same as if the
object is set to 'false'.
The value 'false' indicates that the first Measurement Interval starts
at an arbitrary time and each subsequent Measurement Interval starts
at a time which is determined by jnxSoamLmCfgRepetitionTime.
This object can only be written at row creation time and cannot be
modified once it has been created.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.19 |
jnxSoamLmCfgAlignMeasurementOffsetThis object specifies the offset in minutes from the time of day value
if jnxSoamLmCfgAlignMeasurementIntervals is 'true' and the repetition
time is a factor of 60 minutes. If not, the value of this object
is ignored.
If the Measurement Interval is 15 minutes and
jnxSoamLmCfgAlignMeasurementIntervals is true and if this object was
set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50
minutes past each hour.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.20 |
jnxSoamLmCfgSessionTypeThis object indicates whether the current session is defined to
be 'Proactive' or 'On-Demand'. A value of 'proactive'
indicates the current session is 'Proactive'. A value of 'onDemand'
indicates the current session is 'On-Demand'.
This object can only be written at row creation time and cannot be
modified once it has been created.ro OCTET STRING .1.3.6.1.4.1.2636.3.78.1.2.1.1.21 |
jnxSoamLmCfgSessionStatusThis object indicates the current status of the LM session. A value
of 'active' indicates the current LM session is active, i.e. the current
time lies between the start time and the stop time, and
jnxSoamLmCfgEnabled is true. A value of 'notActive' indicates the
current LM session is not active, i.e. it has not started yet, has
stopped upon reaching the stop time, or is disabled.ro OCTET STRING .1.3.6.1.4.1.2636.3.78.1.2.1.1.22 |
jnxSoamLmCfgHistoryClearThis object when written clears the Loss Measurement history
Table (jnxSoamLmHistoryStatsTable) - all rows are deleted.
When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this value during row creation has no effect.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.23 |
jnxSoamLmCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active, except for jnxSoamLmCfgHistoryClear and jnxSoamLmCfgEnabled
objects. All columns must have a valid value before a row
can be activated.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.24 |
jnxSoamLmCfgMeasurementIntervalThis object specifies the Measurement Interval for FLR statistics,
in minutes. A Measurement Interval of 15 minutes needs to be supported,
other intervals may be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.25 |
jnxSoamLmCfgDestMacAddressThe Target or Destination MAC Address Field to be transmitted.
If jnxSoamLmCfgType is 'lmCcm', the destination MAC address is always a
multicast address indicating the level of the MEG: 01-80-c2-00-00-3y,
where y is the level of the MEG. An error is returned if this object
is set to any other value.
If jnxSoamLmCfgType is 'lmLmm' or 'lmSlm', the destination address is
the unicast address of the destination MEP. An error is returned if
this object is set to a multicast address.
This address will be used if the value of the object
mefSoamLmDestIsMepId is 'false'.
This object is only valid for the entity transmitting the
SOAM LM frames and is ignored by the entity receiving
SOAM LM frames.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.26 |
jnxSoamLmCfgStopTimeTypeThis object specifies the type of stop time to terminate the
SOAM LM session. The stop time can be forever (none), relative, or
fixed.
The value of 'none' indicates that the SOAM LM session never ends once it
has started unless it the session is disabled.
The value of 'immediate' is illegal and a write error will be returned
if this value is used.
The value of 'fixed' stops the SOAM LM session when the
jnxSoamLmFixedStopDateAndTime is less than or equal
to the current system date and time. This
value is used to implement an On-Demand fixed time PM session.
The value of 'relative' stops the SOAM LM session when the time
indicated by jnxSoamLmRelativeStopTime has passed since the session
start time as determined by the jnxSoamLmCfgStartTimeType,
jnxSoamLmCfgFixedStartDateAndTime and jnxSoamLmCfgRelativeStartTime
objects. This value is used to implement an On-Demand relative time
PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.rw JnxSoamTcOperationTimeType .1.3.6.1.4.1.2636.3.78.1.2.1.1.27 |
jnxSoamLmCfgFixedStopDateAndTimeThis object specifies the fixed stop date/time for the
SOAM Loss Measurement session. This object is used only used
if jnxSoamLmStopTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.28 |
jnxSoamLmCfgRelativeStopTimeThis object specifies the relative stop time, from the
session start time, to stop the SOAM LM session. This
object is used only if jnxSoamLmStopTimeType is 'relative' and is
ignored otherwise.
object can only be written at row creation time 1922 and cannot be
modified once it has been created.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.1.1.29 |
jnxSoamLmCfgAvailabilityMeasurementIntervalThis object specifies the availability Measurement Interval in
minutes.
A Measurement Interval of 15 minutes is to be supported, other intervals
can be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.30 |
jnxSoamLmCfgAvailabilityNumConsecutiveMeasPdusThis object specifies a configurable number of consecutive
loss measurement PDUs to be used in evaluating the
availability/unavailability status of each availability
indicator per MEF 10.2.1. Loss Measurement PDUs (LMMs, CCMs or
SLMs) are sent regularly with a period defined by
jnxSoamLmCfgMessagePeriod. Therefore, this object, when
multiplied by mefSoamLmCfgMessagePeriod, 2050 is equivalent to
is equivalent to the Availability parameter of 'delta_t' as
specified by MEF 10.2.1.
If the jnxSoamLmCfgType is lmLMM or lmCCM, this object defines the
number of LMM or CCM PDUs transmitted during each 'delta_t' period.
The Availability flr for a given 'delta_t' can be calculated based
on the counters in the last LMM/R or CCM during this 'delta_t' and
the last LMM/R or CCM in the previous 'delta_t'.
If the jnxSoamLmCfgType is lmSLM, this object defines the number
of SLM PDUs transmitted during each 'delta_t' period. The
Availability flr for a given 'delta_t' is calculated based on the
number of those SLM PDUs that are lost.
If the jnxSoamLmCfgType is lmLMM or lmCCM, the number range of 1
through 10 must be supported. The number range of 10 through 1000000
may be supported, but is not mandatory.
If the jnxSoamLmCfgType is lmSLM, the number range of 10 through
100 must be supported. The number range of 100 through 1000000
may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.31 |
jnxSoamLmCfgAvailabilityFlrThresholdThis object specifies a configurable availability threshold to be
used in evaluating the availability/unavailability status of an
availability indicator per MEF 10.2.1. The availability threshold range
of 0.00 (0) through 1.00 (100000) is supported. This parameter is
equivalent to the Availability parameter of 'C' as specified by
MEF 10.2.1.
Units are in milli-percent, where 1 indicates 0.001 percent.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.32 |
jnxSoamLmCfgAvailabilityNumConsecutiveIntervalsThis object specifies a configurable number of consecutive
availability indicators to be used to determine a change in the
availability status as indicated by MEF 10.2.1. This parameter is
equivalent to the Availability parameter of 'n' as specified
by MEF 10.2.1.
The number range of 1 through 10 must be supported. The number
range of 1 through 1000 may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.33 |
jnxSoamLmCfgAvailabilityNumConsecutiveHighFlrThis object specifies a configurable number of consecutive
availability indicators to be used for assessing CHLI. This
parameter is equivalent to the Resilency parameter of 'p' as
specified by MEF 10.2.1.
jnxSoamLmCfgAvailabilityNumConsecutiveHighFlr must be strictly less than
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals. If not, the count of
high loss intervals over time, jnxSoamLmAvailabilityHighLoss, and the
count of consecutive high loss levels,
jnxSoamLmAvailabilityConsecutiveHighLoss, is disabled.
The number range of 1 through 10 must be supported. The number range
of 1 through 1000 may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.1.1.34 |
jnxSoamLmMeasuredStatsTableThis object contains the last measured results for a SOAM Loss
Measurement session.
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Loss Measurement session is running.
Each object in this table applies only if the corresponding bit is set in
jnxSoamLmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamLmMeasuredStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.2 |
jnxSoamLmMeasuredStatsEntryThe conceptual row of jnxSoamLmMeasuredStatsTable JnxSoamLmMeasuredStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.2.1 |
jnxSoamLmMeasuredStatsForwardFlrThis object contains the last frame loss ratio in the forward direction
calculated by this MEP. The FLR value
is a ratio that is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.2.1.1 |
jnxSoamLmMeasuredStatsBackwardFlrThis object contains the last frame loss ratio in the backward direction
calculated by this MEP. The FLR value
is a ratio that is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.2.1.2 |
jnxSoamLmMeasuredStatsAvailForwardStatusThis object indicates the availability status (the outcome of the
last known availability indicator) in the forward direction.
Note that the status of an availability indicator is not known until
the loss for a number of subsequent availability indicators has been
calculated (as determined by
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals)ro JnxSoamTcAvailabilityType .1.3.6.1.4.1.2636.3.78.1.2.2.1.3 |
jnxSoamLmMeasuredStatsAvailBackwardStatusThis object indicates the availability status (the outcome of the
last availability indicator) in the backward direction.
Note that the status of an availability indicator is not known until
the loss for a number of subsequent availability indicators has been
calculated (as determined by
jnxSoamLmCfgAvailabilityNumConsecutiveIntervals)ro JnxSoamTcAvailabilityType .1.3.6.1.4.1.2636.3.78.1.2.2.1.4 |
jnxSoamLmMeasuredStatsAvailForwardLastTransitionTimeThis object indicates the time of the last transition
between available and unavailable in the forward direction.
If there have been no transitions since the Loss Measurement
Session was started, this is set to 0.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.2.1.5 |
jnxSoamLmMeasuredStatsAvailBackwardLastTransitionTimeThis object indicates the time of the last transition
between available and unavailable in the backward direction.
If there have been no transitions since the Loss Measurement
Session was started, this is set to 0.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.2.1.6 |
jnxSoamLmCurrentStatsTableThis table contains the results for the current Measurement
Interval in a SOAM Loss Measurement session gathered during the interval
indicated by iterator counts.
A row in this table is created automatically
by the SNMP Agent when the Loss Measurement session is configured.
Each row in the table represents the current statistics for a Loss
Measurement session for the defined MEP. This table uses four indices.
The first three indices are the indices of the Maintenance Domain, MaNet,
and MEP tables. The fourth index is the specific LM session on the
selected MEP. There may be more than one LM session per MEP. The
main use case for this is to allow multiple CoS instances to be
operating simultaneously for a MEP.
The objects in this table apply regardless of the value of
jnxSoamLmCfgType unless otherwise specified in the object description.
Except for jnxSoamLmCurrentStatsIndex, jnxSoamLmCurrentStatsStartTime,
jnxSoamLmCurrentStatsElapsedTime and jnxSoamLmCurrentStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamLmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or
restart of a device. SEQUENCE OF JnxSoamLmCurrentStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.3 |
jnxSoamLmCurrentStatsEntryThe conceptual row of jnxSoamLmCurrentStatsTable JnxSoamLmCurrentStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.3.1 |
jnxSoamLmCurrentStatsIndexThe index for the current Measurement Interval for this
PM session. This value will become the value for
jnxSoamLmHistoryStatsIndex once the Measurement Interval
is completed.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.1 |
jnxSoamLmCurrentStatsStartTimeThe time that the current Measurement Interval started.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.3.1.2 |
jnxSoamLmCurrentStatsElapsedTimeThe time that the current Measurement Interval has been running, in 0.01
seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.3.1.3 |
jnxSoamLmCurrentStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.3.1.4 |
jnxSoamLmCurrentStatsForwardTransmittedFramesThis object contains the number of frames transmitted in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.5 |
jnxSoamLmCurrentStatsForwardReceivedFramesThis object contains the number of frames received in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.6 |
jnxSoamLmCurrentStatsForwardMinFlrThis object contains the minimum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.7 |
jnxSoamLmCurrentStatsForwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.8 |
jnxSoamLmCurrentStatsForwardAvgFlrThis object contains the average one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.9 |
jnxSoamLmCurrentStatsBackwardTransmittedFramesThis object contains the number of frames transmitted in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.10 |
jnxSoamLmCurrentStatsBackwardReceivedFramesThis object contains the number of frames received in the
backward direction by this MEP.
For a PM Session of type lmLmm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.11 |
jnxSoamLmCurrentStatsBackwardMinFlrThis object contains the minimum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.12 |
jnxSoamLmCurrentStatsBackwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.13 |
jnxSoamLmCurrentStatsBackwardAvgFlrThis object contains the average one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.14 |
jnxSoamLmCurrentStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or
lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames
transmitted.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.15 |
jnxSoamLmCurrentStatsSoamPdusReceivedThis object contains the count of the number of SOAM PDUs
PDUs received in this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or
lmCcm. This object indicates the number of LMR, CCM, or SLR SOAM
frames received.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.3.1.16 |
jnxSoamLmHistoryStatsTableThis table contains the results for history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session Measurement Interval for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval may be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for jnxSoamLmHistoryStatsIndex, jnxSoamLmHistoryStatsEndTime,
jnxSoamLmHistoryStatsElapsedTime and jnxSoamLmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamLmHistoryStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.4 |
jnxSoamLmHistoryStatsEntryThe conceptual row of jnxSoamLmHistoryStatsTable JnxSoamLmHistoryStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.4.1 |
jnxSoamLmHistoryStatsIndexThe index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for FLR (stored in this table) are based on
iterator count and are indexed independently
of Measurement Intervals for availability
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.1 |
jnxSoamLmHistoryStatsEndTimeThe time that the Measurement Interval ended.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.4.1.2 |
jnxSoamLmHistoryStatsElapsedTimeThe length of time that the Measurement Interval ran for,
in 0.01 seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.4.1.3 |
jnxSoamLmHistoryStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.4.1.4 |
jnxSoamLmHistoryStatsForwardTransmittedFramesThis object contains the number of frames transmitted in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.5 |
jnxSoamLmHistoryStatsForwardReceivedFramesThis object contains the number of frames received in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.6 |
jnxSoamLmHistoryStatsForwardMinFlrThis object contains the minimum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.7 |
jnxSoamLmHistoryStatsForwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.8 |
jnxSoamLmHistoryStatsForwardAvgFlrThis object contains the average one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.9 |
jnxSoamLmHistoryStatsBackwardTransmittedFramesThis object contains the number of frames transmitted in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.10 |
jnxSoamLmHistoryStatsBackwardReceivedFramesThis object contains the number of frames received in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.11 |
jnxSoamLmHistoryStatsBackwardMinFlrThis object contains the minimum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.12 |
jnxSoamLmHistoryStatsBackwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.13 |
jnxSoamLmHistoryStatsBackwardAvgFlrThis object contains the average one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.14 |
jnxSoamLmHistoryStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames
transmitted.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.15 |
jnxSoamLmHistoryStatsSoamPdusReceivedThis object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object applies when jnxSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. This object indicates the number of LMR, CCM, or SLR
SOAM frames received.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.4.1.16 |
jnxSoamLmThresholdCfgTableThis table contains the list of Loss Measurement configuration threshold
values for LM Performance Monitoring.
The main purpose of the threshold configuration table is to configure
threshold alarm notifications indicating that a specific performance
metric is not being met.
Each row in the table represents a Loss Measurement session threshold
set for the defined MEP. This table uses five indices. The first three
indices are the indices of the Maintenance Domain, MaNet, and MEP tables.
The fourth index is the specific LM session on the selected MEP. The
fifth index is the specific threshold set number.
Rows in this table are not created automatically. A row is created in
this table to set up a threshold set on a configured MEP that has a
configured LM session.
If two managers try to 'create' the same row at the same time, the first
creation would succeed, the second creation attempt would result in an
error. The second creation attempt would then need to select a new index
value to successfully create a new row.
An NE needs to support at least one threshold set for NE SOAM PM compliance. A
second threshold set on the NE is desirable. More than two threshold
sets can be configured on the NE if supported on the NE.
All the objects in the row have a default value that disables the
particular threshold measurement. In order to enable a threshold
measurement the particular bit in the jnxSoamLmThresholdCfgEnable object
is to be set to '1' and the selected threshold measurement is to have
a threshold value configured. Non-configured threshold measurements
are disabled by default.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamLmThresholdCfgEntry .1.3.6.1.4.1.2636.3.78.1.2.5 |
jnxSoamLmThresholdCfgEntryThe conceptual row of jnxSoamLmThresholdCfgTable. JnxSoamLmThresholdCfgEntry .1.3.6.1.4.1.2636.3.78.1.2.5.1 |
jnxSoamLmThresholdCfgIndexThe index of the threshold number for the specific LM
threshold entry.
An index value of '1' needs to be supported. Other index values
can also be supported.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.5.1.1 |
jnxSoamLmThresholdCfgEnableA vector of bits that indicates the type of SOAM LM thresholds
notifications that are enabled.
A bit set to '1' enables the specific SOAM LM threshold notification
and when the specific counter is enabled and the threshold is crossed a
notification is generated.
A bit set to '0' disables the specific SOAM LM threshold notification.
If a particular SOAM LM threshold is not supported the BIT value is
set to '0'.
bJnxSoamLmMeasuredFlrForwardThreshold(0)
Enables/disables measured frame loss forward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmMeasuredStatsForwardFlr value is
greater than or equal to the threshold value.
bJnxSoamLmMaxFlrForwardThreshold(1)
Enables/disables maximum frame loss forward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmCurrentStatsForwardMaxFlr value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamLmAvgFlrForwardThreshold(2)
Enables/disables average frame loss forward ratio threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamLmCurrentStatsForwardAvgFlr value is greater
than or equal to the threshold value.
bJnxSoamLmMeasuredFlrBackwardThreshold(3)
Enables/disables measured frame loss backward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmMeasuredStatsBackwardFlr value is
greater than or equal to the threshold value.
bJnxSoamLmMaxFlrBackwardThreshold(4)
Enables/disables maximum frame loss backward ratio threshold
notification. The notification is sent immediately when the
jnxSoamLmCurrentStatsBackwardMaxFlr value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamLmAvgFlrBackwardThreshold(5)
Enables/disables average frame loss backward ratio threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamLmCurrentStatsBackwardAvgFlr value is
greater than or equal to the threshold value.ro Bits .1.3.6.1.4.1.2636.3.78.1.2.5.1.2 |
jnxSoamLmThresholdCfgAvgFlrForwardThresholdThis object is used to set the average forward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.5.1.3 |
jnxSoamLmThresholdCfgAvgFlrBackwardThresholdThis object is used to set the average backward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.5.1.4 |
jnxSoamLmThresholdCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active. All columns are to have a valid value before a row
can be activated.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.5.1.5 |
jnxSoamLmCurrentAvailStatsTableThis object contains the current results for a SOAM Loss Measurement
session for availability statistics gathered during the interval
indicated by jnxSoamLmCfgAvailabilityMeasurementInterval.
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Loss Measurement session is running.
The objects in this table apply regardless of the value of
jnxSoamLmCfgType unless otherwise specified in the object description.
Except for jnxSoamLmCurrentAvailStatsIndex,
jnxSoamLmCurrentAvailStatsStartTime, jnxSoamLmCurrentAvailStatsElapsedTime
and jnxSoamLmCurrentAvailStatsSuspect, each object in this table applies
only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable.
The objects in this table may be persistent upon reboot or restart
of a device. SEQUENCE OF JnxSoamLmCurrentAvailStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.6 |
jnxSoamLmCurrentAvailStatsEntryThe conceptual row of jnxSoamLmCurrentAvailStatsTable JnxSoamLmCurrentAvailStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.6.1 |
jnxSoamLmCurrentAvailStatsIndexThe index for the current availability Measurement Interval for this
PM session. This value will become the value for
jnxSoamLmHistoryAvailStatsIndex once the Measurement Interval
is completed. The duration of the Measurement Interval is specified
by jnxSoamLmCfgAvailabilityMeasurementInterval.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.1 |
jnxSoamLmCurrentAvailStatsStartTimeThe time that the current Measurement Interval started.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.6.1.2 |
jnxSoamLmCurrentAvailStatsElapsedTimeThe time that the current Measurement Interval has been running, in 0.01
seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.6.1.3 |
jnxSoamLmCurrentAvailStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.6.1.4 |
jnxSoamLmCurrentAvailStatsForwardHighLossThis object is the number of high loss intervals (HLI) over
time in the forward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.5 |
jnxSoamLmCurrentAvailStatsBackwardHighLossThis object is the number of high loss intervals (HLI) over
time in the backwards direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.6 |
jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.7 |
jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the backward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.8 |
jnxSoamLmCurrentAvailStatsForwardAvailableThis object contains the number of availability indicators
evaluated as available in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.9 |
jnxSoamLmCurrentAvailStatsBackwardAvailableThis object contains the number of availability indicators
evaluated as available in the backward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.10 |
jnxSoamLmCurrentAvailStatsForwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.11 |
jnxSoamLmCurrentAvailStatsBackwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the backward direction by this MEP
during this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.12 |
jnxSoamLmCurrentAvailStatsForwardMinFlrThis object contains the minimum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 2626 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.13 |
jnxSoamLmCurrentAvailStatsForwardMaxFlrThis object contains the maximum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.14 |
jnxSoamLmCurrentAvailStatsForwardAvgFlrThis object contains the average one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.15 |
jnxSoamLmCurrentAvailStatsBackwardMinFlrThis object contains the minimum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.16 |
jnxSoamLmCurrentAvailStatsBackwardMaxFlrThis object contains the maximum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.17 |
jnxSoamLmCurrentAvailStatsBackwardAvgFlrThis object contains the average one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.6.1.18 |
jnxSoamLmHistoryAvailStatsTableThis table contains the results for availability history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session availability Measurement Interval for the defined
MEP. This table uses five indices. The first three indices are the indices
of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the availability
Measurement Interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for jnxSoamLmHistoryAvailStatsIndex,
jnxSoamLmHistoryAvailStatsEndTime, jnxSoamLmHistoryAvailStatsElapsedTime and
jnxSoamLmHistoryAvailStatsSuspect, each object in this table applies only
if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamLmHistoryAvailStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.7 |
jnxSoamLmHistoryAvailStatsEntryThe conceptual row of jnxSoamLmHistoryAvailStatsTable JnxSoamLmHistoryAvailStatsEntry .1.3.6.1.4.1.2636.3.78.1.2.7.1 |
jnxSoamLmHistoryAvailStatsIndexThe index for the availability Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for availability (stored in this table) are based on
jnxSoamLmCfgAvailabilityMeasurementInterval and are indexed independently
of Measurement Intervals for FLR (stored in jnxSoamLmHistoryStatsTable).
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time. Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.1 |
jnxSoamLmHistoryAvailStatsEndTimeThe time that the Measurement Interval ended.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.7.1.2 |
jnxSoamLmHistoryAvailStatsElapsedTimeThe length of time that the Measurement Interval ran for,
in 0.01 seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.7.1.3 |
jnxSoamLmHistoryAvailStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.2.7.1.4 |
jnxSoamLmHistoryAvailStatsForwardHighLossThis object is the number of high loss intervals (HLI) over
time in the forward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.5 |
jnxSoamLmHistoryAvailStatsBackwardHighLossThis object is the number of high loss intervals (HLI) over
time in the backward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.6 |
jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.7 |
jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.8 |
jnxSoamLmHistoryAvailStatsForwardAvailableThis object contains the number of availability indicators
evaluated as available in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.9 |
jnxSoamLmHistoryAvailStatsBackwardAvailableThis object contains the number of availability indicators
evaluated as available in the backward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.10 |
jnxSoamLmHistoryAvailStatsForwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.11 |
jnxSoamLmHistoryAvailStatsBackwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the backward direction by this MEP
during this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.12 |
jnxSoamLmHistoryAvailStatsForwardMinFlrThis object contains the minimum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.13 |
jnxSoamLmHistoryAvailStatsForwardMaxFlrThis object contains the maximum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.14 |
jnxSoamLmHistoryAvailStatsForwardAvgFlrThis object contains the average one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.15 |
jnxSoamLmHistoryAvailStatsBackwardMinFlrThis object contains the minimum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.16 |
jnxSoamLmHistoryAvailStatsBackwardMaxFlrThis object contains the maximum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.17 |
jnxSoamLmHistoryAvailStatsBackwardAvgFlrThis object contains the average one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 3458 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.2.7.1.18 |
jnxSoamPmDmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.1.3 |
jnxSoamDmCfgTableThis table includes configuration objects and operations for the
Delay Measurement function.
Each row in the table represents a Delay Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP.
A Delay Measurement session is created on an existing MEP by first
accessing the jnxSoamDmOperNextIndex object and using this value as
the jnxSoamDmCfgIndex in the row creation.
Some writable objects in this table are only applicable in certain cases
(as described under each object), and attempts to write values for them
in other cases will be ignored.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamDmCfgEntry .1.3.6.1.4.1.2636.3.78.1.3.1 |
jnxSoamDmCfgEntryThe conceptual row of jnxSoamDmCfgTable. JnxSoamDmCfgEntry .1.3.6.1.4.1.2636.3.78.1.3.1.1 |
jnxSoamDmCfgIndexAn index to the Delay Measurement Configuration table which indicates
the specific measurement session for the MEP.
jnxSoamPmMepOperNextIndex needs to be inspected to find an
available index for row-creation.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused for other PM sessions on the same MEP while this
session is active. The index value keeps increasing until it
wraps to zero. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.1 |
jnxSoamDmCfgTypeThis object indicates what type of Delay Measurement is to
be performed.
dmDmm(1) DMM SOAM PDU generated, DMR responses received
(one-way or two-way measurements)
dm1DmTx(2) 1DM SOAM PDU generated (one-way measurements are made by
the receiver)
dm1DmRx(3) 1DM SOAM PDU received and tracked (one-way measurements)
The exact PDUs to use are specified by this object in combination with
jnxSoamDmCfgVersion.
The value dmDMM is required. The values dm1DmTx and dm1DmRx are optional.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Enumeration .1.3.6.1.4.1.2636.3.78.1.3.1.1.2 |
jnxSoamDmCfgVersionThis object indicates the version of the PDUs used to perform
Delay Measurement.
Version 0 indicates the PDU formats defined in Y.1731-2008.
Version 1 indicates the PDU formats defined in Y.1731-2011.
The exact PDUs to use are specified by this object in combination with
jnxSoamDmCfgType.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.3 |
jnxSoamDmCfgEnabledThis object specifies whether the Delay Measurement session is
enabled.
The value 'true' indicates the Delay Measurement session is enabled AND
SOAM PDUs are sent and/or measurements are collected when the session
is running according to the scheduling objects (start time, stop time,
etc.).
The value 'false' indicates the Delay Measurement session is disabled
AND SOAM PDUs are not sent and/or measurements collected.
For a Delay Measurement session to be removed the row is deleted in
order to release internal resources.
This object can written/modified after row creation time.
If the DM session is enabled it resumes after shutdown/restart.
If the DM session is disabled the current Measurement Interval is
stopped, if it in process at the time, and all the in process calculations
for the partially completed Measurement Interval are finalized.
This object does not affect whether the single-ended Responder is
enabled or not, which is enabled or disabled by the
jnxSoamPmMepDmSingleEndedResponder object.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.4 |
jnxSoamDmCfgMeasurementEnableA vector of bits that indicates the type of SOAM DM counters that
are enabled.
A bit set to '1' enables the specific SOAM DM counter.
A bit set to '0' disables the SOAM DM counter.
If a particular SOAM DM counter is not supported the BIT value is
set to '0'.
Not all SOAM DM counters are supported for all SOAM DM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bSoamPdusSent(0)
Enables/disables the jnxSoamDmCurrentStatsSoamPdusSent
and jnxSoamDmHistoryStatsSoamPdusSent counters.
bSoamPdusReceived(1)
Enables/disables the jnxSoamDmCurrentStatsSoamPdusReceived
and jnxSoamDmHistoryStatsSoamPdusReceived counters.
bFrameDelayTwoWayBins(2)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelay'.
bFrameDelayTwoWayMin(3)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMin
and jnxSoamDmHistoryStatsFrameDelayTwoWayMin counters.
bFrameDelayTwoWayMax(4)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMax
and jnxSoamDmHistoryStatsFrameDelayTwoWayMax counters.
bFrameDelayTwoWayAvg(5)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayAvg
and jnxSoamDmHistoryStatsFrameDelayTwoWayAvg counters.
bFrameDelayForwardBins(6)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelay'.
bFrameDelayForwardMin(7)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMin
and jnxSoamDmHistoryStatsFrameDelayForwardMin counters.
bFrameDelayForwardMax(8)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMax
and jnxSoamDmHistoryStatsFrameDelayForwardMax counters.
bFrameDelayForwardAvg(9)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardAvg
and jnxSoamDmHistoryStatsFrameDelayForwardAvg counters.
bFrameDelayBackwardBins(10)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelay'.
bFrameDelayBackwardMin(11)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMin
and jnxSoamDmHistoryStatsFrameDelayBackwardMin counters.
bFrameDelayBackwardMax(12)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMax
and jnxSoamDmHistoryStatsFrameDelayBackwardMax counters.
bFrameDelayBackwardAvg(13)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardAvg
and jnxSoamDmHistoryStatsFrameDelayBackwardAvg counters.
bIfdvForwardBins(14)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardIfdv'.
bIfdvForwardMin(15)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMin
and jnxSoamDmHistoryStatsIfdvForwardMin counters.
bIfdvForwardMax(16)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMax
and jnxSoamDmHistoryStatsIfdvForwardMax counters.
bIfdvForwardAvg(17)
Enables/disables the jnxSoamDmCurrentStatsIfdvForwardAvg
and jnxSoamDmHistoryStatsIfdvForwardAvg counters.
bIfdvBackwardBins(18)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardIfdv'.
bIfdvBackwardMin(19)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMin
and jnxSoamDmHistoryStatsIfdvBackwardMin counters.
bIfdvBackwardMax(20)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMax
and jnxSoamDmHistoryStatsIfdvBackwardMax counters.
bIfdvBackwardAvg(21)
Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardAvg
and jnxSoamDmHistoryStatsIfdvBackwardAvg counters.
bIfdvTwoWayBins(22)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayIfdv'.
bIfdvTwoWayMin(23)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMin
and jnxSoamDmHistoryStatsIfdvTwoWayMin counters.
bIfdvTwoWayMax(24)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMax
and jnxSoamDmHistoryStatsIfdvTwoWayMax counters.
bIfdvTwoWayAvg(25)
Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayAvg
and jnxSoamDmHistoryStatsIfdvTwoWayAvg counters.
bFrameDelayRangeForwardBins(26)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelayRange'.
bFrameDelayRangeForwardMax(27)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardMax
and jnxSoamDmHistoryStatsFrameDelayRangeForwardMax counters.
bFrameDelayRangeForwardAvg(28)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg
and jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg counters.
bFrameDelayRangeBackwardBins(29)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelayRange'.
bFrameDelayRangeBackwardMax(30)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax
and jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax counters.
bFrameDelayRangeBackwardAvg(31)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg
and jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg counters.
bFrameDelayRangeTwoWayBins(32)
Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter
and the jnxSoamDmHistoryStatsBinsEntry counter
when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelayRange'.
bFrameDelayRangeTwoWayMax(33)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax
and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax counters.
bFrameDelayRangeTwoWayAvg(34)
Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg
and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg counters.
bMeasuredStatsFrameDelayTwoWay(35)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayTwoWay
counter.
bMeasuredStatsFrameDelayForward(36)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayForward
counter.
bMeasuredStatsFrameDelayBackward(37)
Enables/disables the jnxSoamDmMeasuredStatsFrameDelayBackward
counter.
bMeasuredStatsIfdvTwoWay(38)
Enables/disables the jnxSoamDmMeasuredStatsIfdvTwoWay
counter.
bMeasuredStatsIfdvForward(39)
Enables/disables the jnxSoamDmMeasuredStatsIfdvForward
counter.
bMeasuredStatsIfdvBackward(40)
Enables/disables the jnxSoamDmMeasuredStatsIfdvBackward
counter.ro Bits .1.3.6.1.4.1.2636.3.78.1.3.1.1.5 |
jnxSoamDmCfgMessagePeriodThis object specifies the interval between Delay Measurement
OAM message transmission. For Delay Measurement monitoring
applications, the default value is 100ms.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Integer32 UNITS "ms" .1.3.6.1.4.1.2636.3.78.1.3.1.1.6 |
jnxSoamDmCfgPriorityThis object specifies the priority of frames with
Delay Measurement OAM message information.
The default value is to be the value which yields the lowest frame
loss.
This object can only be written at row creation time and cannot be
modified once it has been created.ro IEEE8021PriorityValue (IEEE8021-TC-MIB) .1.3.6.1.4.1.2636.3.78.1.3.1.1.7 |
jnxSoamDmCfgFrameSizeThis object specifies the Delay Measurement frame size between
64 bytes and the maximum transmission unit of the EVC.
The range of frame sizes from 64 through 2000 octets need to be
supported, and the range of frame sizes from 2001 through 9600 octets
is suggested to be supported.
The adjustment to the frame size of the standard frame size is
accomplished by the addition of a Data or Test TLV. A Data or Test TLV
is only added to the frame if the frame size is greater than 64 bytes.
This object is only valid for the entity transmitting the Delay
Measurement frames (dmDmm, dm1DmTx) and is ignored by the entity
receiving frames.
In addition, this object is not valid when jnxSoamDmCfgVersion is 0.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.8 |
jnxSoamDmCfgDataPatternThis object specifies the DM data pattern included in a Data TLV
when the size of the DM frame is determined by the
jnxSoamDmFrameSize object and jnxSoamDmTestTlvIncluded is 'false'.
If the frame size object does not define the DM frame size or
jnxSoamDmTestTlvIncluded is 'true' the value of this object is
ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro JnxSoamTcDataPatternType .1.3.6.1.4.1.2636.3.78.1.3.1.1.9 |
jnxSoamDmCfgTestTlvIncludedIndicates whether a Test TLV or Data TLV is included when the size
of the DM frame is determined by the jnxSoamDmFrameSize object.
A value of 'true' indicates that the Test TLV is to be included. A
value of 'false' indicates that the Data TLV is to be included.
If the frame size object does not define the DM frame size
the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.10 |
jnxSoamDmCfgTestTlvPatternThis object specifies the type of test pattern to be
sent in the DM frame Test TLV when the size
of DM PDU is determined by the jnxSoamDmFrameSize object and
jnxSoamDmTestTlvIncluded is 'true'. If the frame size object
does not define the DM frame size or jnxSoamDmTestTlvIncluded
is 'false' the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro JnxSoamTcTestPatternType .1.3.6.1.4.1.2636.3.78.1.3.1.1.11 |
jnxSoamDmCfgNumIntervalsStoredThis object specifies the number of completed Measurement Intervals
to store in the history statistic table.
At least 32 completed Measurement Intervals are to be stored. 96
Measurement Intervals are recommended to be stored.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.12 |
jnxSoamDmCfgDestMepIdThe Maintenance Association End Point Identifier of
another MEP in the same Maintenance Association to which
the SOAM DM frame is to be sent.
This address will be used if the value of the column
jnxSoamDmDestIsMepId is 'true'. A value of zero
means that the destination MEP ID has not been configured.
This object is only valid for the entity transmitting the Delay
Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable
for the 'dm1DmRx' type.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Dot1agCfmMepIdOrZero .1.3.6.1.4.1.2636.3.78.1.3.1.1.13 |
jnxSoamDmCfgDestIsMepIdA value of 'true' indicates that MEPID of the target MEP is used for
SOAM DM frame transmission.
A value of 'false' indicates that the destination MAC address of the
target MEP is used for SOAM DM frame transmission.
This object is only valid for the entity transmitting the Delay
Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable
for the 'dm1DmRx type.
This object can only be written at row creation time and cannot be
modified once it has been created.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.14 |
jnxSoamDmCfgStartTimeTypeThis object specifies the type of start time of the SOAM DM
session. The start time can be disabled (none), immediate, relative,
or fixed.
The value of 'none' is illegal and a write error will be returned
if this value is used.
The value of 'immediate' starts the SOAM DM session when the
jnxSoamDmCfgEnabled is true.
The value of 'fixed' starts the SOAM DM session when the
jnxSoamDmFixedStartDateAndTime is less than or equal to the current
system date and time and jnxSoamDmCfgEnabled is true. This value is used
to implement an On-Demand fixed time PM session.
The value of 'relative' starts the SOAM DM session when the current
system date and time minus the jnxSoamDmRelativeStartTime is greater than
or equal to the system date and time when the jnxSoamDmStartTimeType
object was written and jnxSoamDmCfgEnabled is true. This value is used
to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.ro JnxSoamTcOperationTimeType .1.3.6.1.4.1.2636.3.78.1.3.1.1.15 |
jnxSoamDmCfgRepetitionTimeThis object specifies a configurable repetition time between
Measurement Intervals in a Delay Measurement session in seconds.
If the value is 0 (none), there is no time gap between the end of one
Measurement Interval and the start of a new Measurement Interval.
This is the normal usage case.
If the value is greater than one Measurement Interval there is time gap
between the end of one Measurement Interval and the start of the next
Measurement Interval. The repetition time specifies the time between
the start of consecutive Measurement Intervals; hence the gap between
the end of one Measurement Interval and the start of the next is equal
to the difference between the repetition time and the measurement
interval. During this gap, no SOAM PDUs are sent for this session and
no measurements are made.
If the value is greater 0 but less than or equal to the measurement
interval, an error is returned.
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.16 |
jnxSoamDmCfgAlignMeasurementIntervalsThis object specifies whether the Measurement Intervals for
the Delay Measurement session are aligned with a zero offset to
real time.
The value 'true' indicates that each Measurement Interval starts
at a time which is aligned to NE time source hour, if the repetition
time (or the Measurement Interval, if the repetition time is 0) is
a factor of an hour, i.e. 60min/15min = 4. For instance, a
Measurement Interval/Repetition Time of 15 minutes would stop/start
the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A
Measurement Interval/Repetition Time of 7 minutes would not align
to the hour since 7 minutes is NOT a factor of an hour, i.e.
60min/7min = 8.6. In this case the behavior is the same as if the
object is set to 'false'.
The value 'false' indicates that the first Measurement Interval starts
at an arbitrary time and each subsequent Measurement Interval starts
at a time which is determined by jnxSoamLmCfgRepetitionTime.
This object can only be written at row creation time and cannot be
modified once it has been created.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.17 |
jnxSoamDmCfgInterFrameDelayVariationSelectionOffsetThis object specifies the selection offset for
Inter-Frame Delay Variation measurements. If this value
is set to n, then the IFDV is calculated by taking the
difference in frame delay between frame F and frame (F+n).
This object can only be written at row creation time and cannot be
modified once it has been created.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.18 |
jnxSoamDmCfgSessionTypeThis object indicates whether the current session is defined to
be 'Proactive' or 'On-Demand'. A value of 'proactive'
indicates the current session is 'Proactive'. A value of 'onDemand'
indicates the current session is 'On-Demand'.
This object can only be written at row creation time and cannot be
modified once it has been created.ro OCTET STRING .1.3.6.1.4.1.2636.3.78.1.3.1.1.19 |
jnxSoamDmCfgSessionStatusThis object indicates the current status of the DM session. A value
of 'active' indicates the current DM session is active, i.e. the current
time lies between the start time and the stop time, and
jnxSoamDmCfgEnabled is true. A value of 'notActive' indicates the
current DM session is not active, i.e. it has not started yet, has
stopped upon reaching the stop time, or is disabled.ro OCTET STRING .1.3.6.1.4.1.2636.3.78.1.3.1.1.20 |
jnxSoamDmCfgHistoryClearThis object when written clears the Delay Measurement history
tables (jnxSoamDmHistoryStatsTable)
- all rows are deleted. When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this object at row creation has no effect.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.21 |
jnxSoamDmCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active, except for jnxSoamDmCfgEnabled and jnxSoamDmCfgHistoryClear
objects. All columns are to have a valid value before a row
can be activated.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.22 |
jnxSoamDmCfgMeasurementIntervalThis object specifies a Measurement Interval in minutes.
A Measurement Interval 15 minutes needs to be supported, other intervals
may be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.23 |
jnxSoamDmCfgDestMacAddressThe Target or Destination MAC Address Field to be transmitted.
If mefSoamDmCfgType is 'dmDmm', the destination address is to be the
unicast address of the destination MEP. An error is returned if this
object is set to a multicast address.
If mefSoamDmCfgType is 'dm1DmTx', the destination address is normally the
unicast address of the destination MEP, but can be a multicast address
indicating the level of the MEG: 01-80-c2-00-00-3y, where y is the
level of the MEG. An error is returned if this object is set to any
other multicast address.
If mefSoamDmCfgType is 'dm1DmRx', this object is ignored.
This address will be used if the value of the object
mefSoamDmDestIsMepId is 'false'.
This object is only valid for the entity transmitting the
SOAM DM frames and is ignored by the entity receiving
SOAM DM frames.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.24 |
jnxSoamDmCfgSourceMacAddressThe Source MAC Address Field of the received SOAM DM session PDUs.
If mefSoamDmCfgType is dm1DmRx this object indicates the source
address of the dm1DmTx DM session.
This object is only valid for mefSoamDmCfgType set to dm1DmRx. It is
ignored for mefSoamDmCfgType set to dmDmm or dm1DmTx.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.25 |
jnxSoamDmCfgFixedStartDateAndTimeThis object specifies the fixed start date/time for the
SOAM Delay Measurement session. This object is used only used if
mefSoamDmStartTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.26 |
jnxSoamDmCfgRelativeStartTimeThis object specifies the relative start time, from
the current system time, for the SOAM DM session. This
object is used only if mefSoamDmStartTimeType is 'relative'
and is ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.27 |
jnxSoamDmCfgStopTimeTypeThis object specifies the type of stop time to terminate the
SOAM DM session. The stop time can be forever (none), relative, or
fixed.
The value of 'none' indicates that the SOAM DM session never ends once it
has started unless the session is disabled.
The value of 'immediate' is illegal and a write error will be returned
if this value is used.
The value of 'fixed' stops the SOAM DM session when the
mefSoamDmFixedStopDateAndTime is less than or equal
to the current system date. This
value is used to implement an On-Demand fixed time PM session.
The value of 'relative' stops the SOAM DM session when the time
indicated by mefSoamDmRelativeStopTime has passed since the session
start time as determined by the mefSoamDmCfgStartTimeType,
mefSoamDmCfgFixedStartDateAndTime and mefSoamDmCfgRelativeStartTime
objects.
This value is used to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.rw JnxSoamTcOperationTimeType .1.3.6.1.4.1.2636.3.78.1.3.1.1.28 |
jnxSoamDmCfgFixedStopDateAndTimeThis object specifies the fixed stop date/time for the
SOAM Delay Measurement session. This object is used only used
if mefSoamDmStopTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.29 |
jnxSoamDmCfgRelativeStopTimeThis object specifies the relative stop time, from the
session start time, to stop the SOAM DM session. This
object is used only if mefSoamDmStopTimeType is 'relative' and is
otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.1.1.30 |
jnxSoamDmCfgAlignMeasurementOffsetThis object specifies the offset in minutes from the time of day value
if mefSoamDmCfgAlignMeasurementIntervals is 'true' and the repetition
time is a factor of 60 minutes. If not, the value of this object
is ignored.
If the Measurement Interval is 15 minutes and
mefSoamDmCfgAlignMeasurementIntervals is true and if this object was
set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50
minutes past each hour.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.31 |
jnxSoamDmCfgNumMeasBinsPerFrameDelayIntervalThis object specifies the number of measurement bins
per Measurement Interval for Frame Delay measurements.
At least 3 bins are to be supported; at least 10 bins are recommended
to be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.32 |
jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationIntervalThis object specifies the number of measurement bins
per Measurement Interval for Inter-Frame Delay Variation
measurements.
The minimum number of measurement bins to be supported is 2. The
supported is 10.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.33 |
jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeIntervalThis object specifies the number of measurement bins
per Measurement Interval for Frame Delay Range measurements.
At least 2 bins are to be supported; at least 10 bins are recommended
to be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.1.1.34 |
jnxSoamDmMeasuredStatsTableThis object contains the last measured results for a SOAM Delay
Measurement session.
Each row in the table represents a Delay Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Delay Measurement session is running.
Each object in this table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or restart
of a device. SEQUENCE OF JnxSoamDmMeasuredStatsEntry .1.3.6.1.4.1.2636.3.78.1.3.2 |
jnxSoamDmMeasuredStatsEntryThe conceptual row of jnxSoamDmMeasuredStatsTable JnxSoamDmMeasuredStatsEntry .1.3.6.1.4.1.2636.3.78.1.3.2.1 |
jnxSoamDmMeasuredStatsFrameDelayTwoWayThis object contains the two-way frame delay calculated by this
MEP from the last received SOAM PDU.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.2.1.1 |
jnxSoamDmMeasuredStatsFrameDelayForwardThis object contains the frame delay in the forward direction
calculated by this MEP from the last received SOAM PDU. The value of this
object may not be accurate in the absence of sufficiently precise clock
synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.2.1.2 |
jnxSoamDmMeasuredStatsFrameDelayBackwardThis object contains the frame delay in the backward direction
calculated by this MEP from the last received SOAM PDU. The value of this
object may not be accurate in the absence of sufficiently precise clock
synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.2.1.3 |
jnxSoamDmMeasuredStatsIfdvTwoWayThis object contains the last two-way inter-frame delay
interval calculated by this MEP.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.2.1.4 |
jnxSoamDmMeasuredStatsIfdvForwardThis object contains the last one-way inter-frame delay
interval in the forward direction calculated by this MEP.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.2.1.5 |
jnxSoamDmMeasuredStatsIfdvBackwardThis object contains the last one-way inter-frame delay
interval in the backward direction calculated by this MEP.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.2.1.6 |
jnxSoamDmCurrentStatsTableThis table contains the results for the current Measurement
Interval in a SOAM Delay Measurement session gathered during the interval
indicated by iterator count.
A row in this table is created automatically
by the SNMP Agent when the Delay Measurement session is configured.
Each row in the table represents the current statistics for a Delay
Measurement session for the defined MEP. This table uses four indices.
The first three indices are the indices of the Maintenance Domain, MaNet,
and MEP tables. The fourth index is the specific DM session on the
selected MEP. There can be more than one DM session per MEP.
The objects in this table apply regardless of the value of
jnxSoamDmCfgType unless otherwise specified in the object description.
Backward and two-way statistic objects are undefined if jnxSoamDmCfgType
is dm1DmRx.
Except for jnxSoamDmCurrentStatsIndex, jnxSoamDmCurrentStatsStartTime
jnxSoamDmCurrentStatsElapsedTime and jnxSoamDmCurrentStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or
restart of a device. SEQUENCE OF JnxSoamDmCurrentStatsEntry .1.3.6.1.4.1.2636.3.78.1.3.3 |
jnxSoamDmCurrentStatsEntryThe conceptual row of jnxSoamDmCurrentStatsTable JnxSoamDmCurrentStatsEntry .1.3.6.1.4.1.2636.3.78.1.3.3.1 |
jnxSoamDmCurrentStatsIndexThe index for the current Measurement Interval for this
PM session. This value will become the value for
jnxSoamDmHistoryStatsIndex once the Measurement Interval
is completed.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.3.1.1 |
jnxSoamDmCurrentStatsStartTimeThe time that the current Measurement Interval started.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.3.1.2 |
jnxSoamDmCurrentStatsElapsedTimeThe time that the current Measurement Interval has been running, in 0.01
seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.3.1.3 |
jnxSoamDmCurrentStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is to be set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.3.1.4 |
jnxSoamDmCurrentStatsFrameDelayTwoWayMinThis object contains the minimum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.5 |
jnxSoamDmCurrentStatsFrameDelayTwoWayMaxThis object contains the maximum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.6 |
jnxSoamDmCurrentStatsFrameDelayTwoWayAvgThis object contains the average two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.7 |
jnxSoamDmCurrentStatsFrameDelayForwardMinThis object contains the minimum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.8 |
jnxSoamDmCurrentStatsFrameDelayForwardMaxThis object contains the maximum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.9 |
jnxSoamDmCurrentStatsFrameDelayForwardAvgThis object contains the average one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.10 |
jnxSoamDmCurrentStatsFrameDelayBackwardMinThis object contains the minimum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.11 |
jnxSoamDmCurrentStatsFrameDelayBackwardMaxThis object contains the maximum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.12 |
jnxSoamDmCurrentStatsFrameDelayBackwardAvgThis object contains the average one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.13 |
jnxSoamDmCurrentStatsIfdvForwardMinThis object contains the minimum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.14 |
jnxSoamDmCurrentStatsIfdvForwardMaxThis object contains the maximum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.15 |
jnxSoamDmCurrentStatsIfdvForwardAvgThis object contains the average one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.16 |
jnxSoamDmCurrentStatsIfdvBackwardMinThis object contains the minimum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.17 |
jnxSoamDmCurrentStatsIfdvBackwardMaxThis object contains the maximum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.18 |
jnxSoamDmCurrentStatsIfdvBackwardAvgThis object contains the average one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.19 |
jnxSoamDmCurrentStatsIfdvTwoWayMinThis object contains the minimum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.20 |
jnxSoamDmCurrentStatsIfdvTwoWayMaxThis object contains the maximum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.21 |
jnxSoamDmCurrentStatsIfdvTwoWayAvgThis object contains the average two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.22 |
jnxSoamDmCurrentStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamDmCfgType is dmDmm or dm1DmTx and
is undefined if jnxSoamDmCfgType is dm1DmRx. It indicates the
number of DMM or 1DM SOAM frames transmitted.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.3.3.1.23 |
jnxSoamDmCurrentStatsSoamPdusReceivedThis object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object indicates the number of DMR and 1DM SOAM frames
received. This object applies when jnxSoamDmCfgTypeis dmDmm or
dm1DmRx and is undefined if jnxSoamDmCfgTypeis dm1DmTx.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.3.3.1.24 |
jnxSoamDmCurrentStatsFrameDelayRangeForwardMaxThis object contains the maximum one-way frame delay range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.25 |
jnxSoamDmCurrentStatsFrameDelayRangeForwardAvgThis object contains the average one-way frame delay range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.26 |
jnxSoamDmCurrentStatsFrameDelayRangeBackwardMaxThis object contains the maximum one-way frame delay range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.27 |
jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvgThis object contains the average one-way frame delay range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.28 |
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMaxThis object contains the maximum two-way frame delay range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.29 |
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvgThis object contains the average two-way frame delay range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.3.1.30 |
jnxSoamDmHistoryStatsTableThis table contains the results for history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a Delay Measurement session for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific DM session on the selected MEP. The fifth index is the
Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
The objects in this table apply regardless of the value of
jnxSoamDmCfgType unless otherwise specified in the object description.
Backward and two-way statistic objects are undefined if jnxSoamDmCfgType
is dm1DmRx.
Except for jnxSoamDmHistoryStatsIndex, jnxSoamDmHistoryStatsEndTime,
jnxSoamDmHistoryStatsElapsedTime and jnxSoamDmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamDmHistoryStatsEntry .1.3.6.1.4.1.2636.3.78.1.3.4 |
jnxSoamDmHistoryStatsEntryThe conceptual row of jnxSoamDmHistoryStatsTable JnxSoamDmHistoryStatsEntry .1.3.6.1.4.1.2636.3.78.1.3.4.1 |
jnxSoamDmHistoryStatsIndexThe index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.4.1.1 |
jnxSoamDmHistoryStatsEndTimeThe time that the Measurement Interval ended.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.4.1.2 |
jnxSoamDmHistoryStatsElapsedTimeThe length of time that the Measurement Interval ran for,
in 0.01 seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.4.1.3 |
jnxSoamDmHistoryStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.4.1.4 |
jnxSoamDmHistoryStatsFrameDelayTwoWayMinThis object contains the minimum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.5 |
jnxSoamDmHistoryStatsFrameDelayTwoWayMaxThis object contains the maximum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.6 |
jnxSoamDmHistoryStatsFrameDelayTwoWayAvgThis object contains the average two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.7 |
jnxSoamDmHistoryStatsFrameDelayForwardMinThis object contains the minimum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.8 |
jnxSoamDmHistoryStatsFrameDelayForwardMaxThis object contains the maximum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.9 |
jnxSoamDmHistoryStatsFrameDelayForwardAvgThis object contains the average one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.10 |
jnxSoamDmHistoryStatsFrameDelayBackwardMinThis object contains the minimum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.11 |
jnxSoamDmHistoryStatsFrameDelayBackwardMaxThis object contains the maximum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.12 |
jnxSoamDmHistoryStatsFrameDelayBackwardAvgThis object contains the average one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.13 |
jnxSoamDmHistoryStatsIfdvForwardMinThis object contains the minimum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.14 |
jnxSoamDmHistoryStatsIfdvForwardMaxThis object contains the maximum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.15 |
jnxSoamDmHistoryStatsIfdvForwardAvgThis object contains the average one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.16 |
jnxSoamDmHistoryStatsIfdvBackwardMinThis object contains the minimum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.17 |
jnxSoamDmHistoryStatsIfdvBackwardMaxThis object contains the maximum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.18 |
jnxSoamDmHistoryStatsIfdvBackwardAvgThis object contains the average one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.19 |
jnxSoamDmHistoryStatsIfdvTwoWayMinThis object contains the minimum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.20 |
jnxSoamDmHistoryStatsIfdvTwoWayMaxThis object contains the maximum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.21 |
jnxSoamDmHistoryStatsIfdvTwoWayAvgThis object contains the average two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.22 |
jnxSoamDmHistoryStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when jnxSoamDmCfgType is dmDmm or dm1DmTx and
is undefined if jnxSoamDmCfgType is dm1DmRx. It indicates the
number of DMM or 1DM SOAM frames transmitted.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.3.4.1.23 |
jnxSoamDmHistoryStatsSoamPdusReceivedThis object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object indicates the number of DMR and 1DM SOAM frames
received. This object applies when jnxSoamDmCfgType is dmDmm or
dm1DmRx and is undefined if jnxSoamDmCfgType is dm1DmTx.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.3.4.1.24 |
jnxSoamDmHistoryStatsFrameDelayRangeForwardMaxThis object contains the maximum one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.25 |
jnxSoamDmHistoryStatsFrameDelayRangeForwardAvgThis object contains the average one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.26 |
jnxSoamDmHistoryStatsFrameDelayRangeBackwardMaxThis object contains the maximum one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.27 |
jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvgThis object contains the average one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.28 |
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMaxThis object contains the maximum two-way Frame Delay Range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.29 |
jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvgThis object contains the average two-way Frame Delay Range
Interval.
The value of this object is undefined when jnxSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.4.1.30 |
jnxSoamDmThresholdCfgTableThis table contains the list of Delay Measurement threshold configuration
values for DM Performance Monitoring.
The main purpose of the threshold configuration table is to configure
threshold alarm notifications indicating that a specific performance
metric is not being met.
Each row in the table represents a Delay Measurement session threshold
set for the defined MEP. This table uses five indices. The first three
indices are the indices of the Maintenance Domain, MaNet, and MEP tables.
The fourth index is the specific DM session on the selected MEP. The
fifth index is the specific threshold set number.
Rows in this table are not created automatically. A row is created in
this table to set up a threshold set on a configured MEP that has a
configured DM session.
An NE needs to support at least one threshold set for NE SOAM PM compliance. A
second threshold set on the NE is desirable. More than two threshold
sets on the NE can be configured if supported on the NE.
All the objects in the row have a default value that disables the
particular threshold measurement. In order to enable a threshold
measurement the particular bit in the jnxSoamDmThresholdCfgEnable object
is to be set to '1' and the selected threshold measurement is to have
a threshold value configured. Non-configured threshold measurements
are disabled by default.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamDmThresholdCfgEntry .1.3.6.1.4.1.2636.3.78.1.3.5 |
jnxSoamDmThresholdCfgEntryThe conceptual row of jnxSoamDmThresholdCfgTable. JnxSoamDmThresholdCfgEntry .1.3.6.1.4.1.2636.3.78.1.3.5.1 |
jnxSoamDmThresholdCfgIndexThe index of the threshold number for the specific DM
threshold entry.
An index value of '1' is to be supported. Other index values
can be supported.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.5.1.1 |
jnxSoamDmThresholdCfgEnableA vector of bits that indicates the type of SOAM DM threshold
notifications that are enabled.
A bit set to '1' enables the specific SOAM DM threshold notification
and when the specific counter is enabled and the threshold is crossed a
notification is generated.
A bit set to '0' disables the specific SOAM DM threshold notification.
If a particular SOAM DM threshold is not supported the BIT value is
set to '0'.
bJnxSoamDmMeasuredFrameDelayTwoWayThreshold(0)
Enables/disables measured frame two-way delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayTwoWay value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayTwoWayThreshold(1)
Enables/disables maximum frame two-way delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayTwoWayMax value is
greater than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayTwoWayThreshold(2)
Enables/disables average frame two-way delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvTwoWayThreshold(3)
Enables/disables measured frame IFDV two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvTwoWay value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvTwoWayThreshold(4)
Enables/disables maximum frame IFDV two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvTwoWayThreshold(5)
Enables/disables average frame IFDV two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeTwoWayThreshold(6)
Enables/disables maximum Frame Delay Range two-way threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeTwoWayThreshold(7)
Enables/disables average Frame Delay Range two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredFrameDelayForwardThreshold(8)
Enables/disables measured forward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayForward value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayForwardThreshold(9)
Enables/disables maximum forward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayForwardMax value is
greater than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayForwardThreshold(10)
Enables/disables average forward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvForwardThreshold(11)
Enables/disables measured frame IFDV forward threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvForward value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvForwardThreshold(12)
Enables/disables maximum frame IFDV forward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvForwardThreshold(13)
Enables/disables average frame IFDV forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeForwardThreshold(14)
Enables/disables maximum Frame Delay Range forward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeForwardThreshold(15)
Enables/disables average Frame Delay Range forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredFrameDelayBackwardThreshold(16)
Enables/disables measured backward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsFrameDelayBackward value is
greater than or equal to threshold value.
bJnxSoamDmMaxFrameDelayBackwardThreshold(17)
Enables/disables maximum backward frame delay threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayBackwardMax value is
greater than or equal to threshold value in a
Measurement Interval.
bJnxSoamDmAvgFrameDelayBackwardThreshold(18)
Enables/disables average backward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayBackwardAvg value is
greater than or equal to the threshold value.
bJnxSoamDmMeasuredIfdvBackwardThreshold(19)
Enables/disables measured frame IFDV backward threshold
notification. The notification is sent immediately when the
jnxSoamDmMeasuredStatsIfdvBackward value is greater
than or equal to threshold value.
bJnxSoamDmMaxIfdvBackwardThreshold(20)
Enables/disables maximum frame IFDV backward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsIfdvBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgIfdvBackwardThreshold(21)
Enables/disables average frame IFDV backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsIfdvBackwardAvg value is greater
than or equal to the threshold value.
bJnxSoamDmMaxFrameDelayRangeBackwardThreshold(22)
Enables/disables maximum Frame Delay Range backward threshold
notification. The notification is sent immediately when the
jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bJnxSoamDmAvgFrameDelayRangeBackwardThreshold(23)
Enables/disables average Frame Delay Range backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg value is greater
than or equal to the threshold value.ro Bits .1.3.6.1.4.1.2636.3.78.1.3.5.1.2 |
jnxSoamDmThresholdCfgAvgFrameDelayTwoWayThresholdThis object is used to set the average two-way delay threshold
value that will be used to determine if a threshold notification is
generated.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.5.1.3 |
jnxSoamDmThresholdCfgAvgIfdvTwoWayThresholdThis object is used to set the average two-way IFDV threshold
value that will be used to determine if a threshold notification is
generated.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.2636.3.78.1.3.5.1.4 |
jnxSoamDmThresholdCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active. All columns are to have a valid value before a row
can be activated.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.3.5.1.5 |
jnxSoamDmCfgMeasBinTableThis table includes configuration objects for the Delay Measurement
bins to collect stats.
Each row in the table is automatically created when the Delay
Measurement session is defined for the selected MEP. The number of rows
created is based upon three items: the DM type, the number of bins
defined for each type, and whether bins are enabled for each type.
The first four indices are the same as used to create the DM session:
Maintenance Domain, MaNet, MEP identification, and jnxSoamDmCfgIndex. The
fifth index is the type of bin, and the sixth index is the bin number.
For a dmDmm session all nine types of bins can be created. For a dm1DmmTx
session no bins are created. For a dm1DmmRx session only types
forwardFrameDelay, forwardIfdv, and forwardFrameDelayRange can be created.
The number of bins created for a bin type is based upon: the
jnxSoamDmCfgNumMeasBinsPerFrameDelayInterval object, the
jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval object, the
jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval object, and
the jnxSoamDmCfgMeasurementEnable object.
For instance, if a dmDmm session with Bins per Frame Delay Interval
set to 5, Bins per Frame Delay Variation Interval set to 3, and Frame
Delay Range set to 2 (default), all of the appropriate bits set in
jnxSoamDmMeasurementCfgEnable, the following number of rows would be
created:
For bin types TwoWayFrameDelay(1), forwardFrameDelay(2), and
backwardFrameDelay(3) = 5 bins * 3 types = 15 rows
For bin types TwoWayIfdv(4), forwardIfdv(5), backwardIfdv(6) =
3 bins * 3 types = 9 rows.
For bins types twoWayFrameDelayRange(7), forwardFrameDelayRange(8),
backwardFrameDelayRange(9) =
2 bins * 3 types = 6 rows.
This gives a total of 30 rows created for the DMM session example.
Each value in the bin defaults to 5000us greater than the previous bin,
with the first bin default value set to 0.
For the delay example above (5 bins), the following default values
would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < 15,000us)
bin 4: 15000 (range is 15,000us <= measurement < 20,000us)
bin 5: 20000 (range is 20,000us <= measurement < infinity)
For the delay variation example above (3 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < infinity)
For the frame delay range example above (2 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < infinity)
The writable objects in this table need to be persistent upon reboot
or restart of a device.
Rows are only created if the corresponding measurement type has been enabled
via the jnxSoamDmCfgMeasurementEnable object. SEQUENCE OF JnxSoamDmCfgMeasBinEntry .1.3.6.1.4.1.2636.3.78.1.3.6 |
jnxSoamDmCfgMeasBinEntryThe conceptual row of jnxSoamDmCfgMeasBinTable. JnxSoamDmCfgMeasBinEntry .1.3.6.1.4.1.2636.3.78.1.3.6.1 |
jnxSoamDmCfgMeasBinTypeThis object specifies whether the bin number is for
Frame Delay or Inter-Frame Delay Variation. JnxSoamTcDelayMeasurementBinType .1.3.6.1.4.1.2636.3.78.1.3.6.1.1 |
jnxSoamDmCfgMeasBinNumberThis object specifies the bin number for the
configured boundary. The first bin has bin number 1. Unsigned32 .1.3.6.1.4.1.2636.3.78.1.3.6.1.2 |
jnxSoamDmCfgMeasBinLowerBoundThis object specifies the lower boundary for a
measurement bin. The upper boundary is defined by the next bin
value or infinite for the last bin defined.
The measurement boundary for each measurement bin is to
be larger than the measurement boundary of the preceding
measurement bin. By default, the next bin is set to 5000us larger
than the lower bin boundary.
The values in a bin boundary object represents the time range
used to segregate delay data into the appropriate statistical
data bin. For five bins with default values, each bin has the
following time range:
bin 1 = 0, range is 0us <= measurement < 5,000us
bin 2 = 5000, range is 5,000us <= measurement < 10,000us
bin 3 = 10000, range is 10,000us <= measurement < 15,000us
bin 4 = 15000, range is 15,000us <= measurement < 20,000us
< infinity
The first bin boundary (jnxSoamDmCfgBinNumber set to 1) always contains
the value of 0. Attempting to write a non-zero value to this bin will
result in an error.rw Unsigned32 UNITS "microseconds (us)" .1.3.6.1.4.1.2636.3.78.1.3.6.1.3 |
jnxSoamDmCurrentStatsBinsTableThis table contains the result bins for the current Measurement
Interval in a SOAM Delay Measurement session.
Each row in the table represents the current bin statistics for a
Delay Measurement session for the defined MEP. This table uses six
indices. The first three indices are the indices of the Maintenance
Domain, MaNet, and MEP tables. The fourth index is the specific DM
session on the selected MEP. The fifth index indicates bin type and
the sixth indicates the specific bin number.
A row in this table is created automatically by the SNMP Agent when
the Delay Measurement session is configured and the bin counter value
is set to 0.
The objects in this table are ignored if jnxSoamDmCfgType is 1DmTx.
This table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamDmCurrentStatsBinsEntry .1.3.6.1.4.1.2636.3.78.1.3.7 |
jnxSoamDmCurrentStatsBinsEntryThe conceptual row of jnxSoamDmCurrentStatsBinsTable JnxSoamDmCurrentStatsBinsEntry .1.3.6.1.4.1.2636.3.78.1.3.7.1 |
jnxSoamDmCurrentStatsBinsCounterThis object contains the count of the number of completed
measurements initiated in this Measurement Interval whose value
falls within the range specified for this bin (that is, greater
than or equal to the measurement boundary for the bin, and
(unless the bin is the last bin) less than the measurement
boundary for the following bin.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.3.7.1.1 |
jnxSoamDmHistoryStatsBinsTableThis table contains the result bins for the history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a specific bin in a Delay Measurement session for the
defined MEP. This table uses seven indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP. The
fifth index is the Measurement Interval. The sixth index is the
specific bin type. The seventh index is the specific bin number.
Rows in this table pertaining to a given Measurement Interval are
row in the
jnxSoamDmHistoryStatsTable is deleted.
The objects in this table are ignored if jnxSoamDmCfgType is 1DmTx.
This table applies only if the corresponding bit is set in
jnxSoamDmCfgMeasurementEnable.
The objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF JnxSoamDmHistoryStatsBinsEntry .1.3.6.1.4.1.2636.3.78.1.3.8 |
jnxSoamDmHistoryStatsBinsEntryThe conceptual row of jnxSoamDmHistoryStatsBinsTable JnxSoamDmHistoryStatsBinsEntry .1.3.6.1.4.1.2636.3.78.1.3.8.1 |
jnxSoamDmHistoryStatsBinsCounterThis object contains the count of the number of completed
measurements initiated in this Measurement Interval whose value
falls within the range specified for this bin (that is, greater
than or equal to the measurement boundary for the bin, and
(unless the bin is the last bin) less than the measurement
boundary for the following bin.ro Gauge32 .1.3.6.1.4.1.2636.3.78.1.3.8.1.1 |
jnxSoamPmNotificationCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.1.4 |
jnxSoamPmNotificationObj OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.1.5 |
jnxSoamPmNotificationObjDateAndTimeThis object contains the time and date at the time that
the notification event is detected, not the time of the notification
generation.
This object is used only for notifications. The mechanism to set and keep
current the date and time is not specified.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.5.1 |
jnxSoamPmNotificationObjThresholdIdThe Object Identifier of the object that caused the generation of the
notification from the jnxSoamLmThresholdEntry or jnxSoamDmThresholdEntry.
This object is only used for the notification.ro OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.1.5.2 |
jnxSoamPmNotificationObjThresholdConfigThe configured threshold value of the object that caused the generation
of the notification.
This object is only used for the notification.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.5.3 |
jnxSoamPmNotificationObjThresholdValueThe measured value of the object at the time of the generation of the
Notification, from the jnxSoamLmMeasuredStatsTable,
jnxSoamLmCurrentStatsTable,
jnxSoamDmMeasuredStatsTable or jnxSoamDmCurrentStatsTable.
This object is only used for the notification.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.5.4 |
jnxSoamPmNotificationObjSuspectThe suspect flag for the current Measurement Interval in which the
notification was generated from the jnxSoamLmCurrentStatsTable,
or jnxSoamDmCurrentStatsTable.
This object is only used for the notification.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.5.5 |
jnxSoamPmNotificationObjCrossingTypeThe Notification Crossing Type of the object that caused the generation
of the notification from the jnxSoamLmThresholdEntry or
jnxSoamDmThresholdEntry.
aboveAlarm(1) indicates that the crossing type alarm was an above
threshold
setAlarm(2) indicates that the crossing type alarm was a set
threshold
clearAlarm(3) indicates that the crossing type alarm was a clear
threshold
This object is only used for the notification.ro Enumeration .1.3.6.1.4.1.2636.3.78.1.5.6 |
jnxSoamPmNotificationObjDestinationMepThe MAC address of the Destination MEP associated the notification found
in either the jnxSoamDmCfgTable or jnxSoamLmCfgTable.
This object is only used for the notification.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.5.7 |
jnxSoamPmNotificationObjPriorityThe CoS priority of the associated notification found
in either the jnxSoamDmCfgTable or jnxSoamLmCfgTable.
This object is only used for the notification.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.5.8 |
jnxSoamPmNotificationTotalFlapsThe measured value of total number of flaps occured during the
flap trap timer itnerval.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.5.9 |
jnxSoamPmNotificationAccTotalFlapsThe measured value of total number of accumulated flaps occured during the
flap trap timer itnerval.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.5.10 |
jnxSoamPmNotificationObjThresholdLastValueThe measured value of the object at the time of the generation of the
last Notification during the flap trap timer interval.
This object is only used for the notification.ro Unsigned32 .1.3.6.1.4.1.2636.3.78.1.5.11 |
jnxSoamPmNotificationObjCurrentStateThe Current Notification Crossing Type of the
object that caused the generation
of the notification at the end of timer interval
from the jnxSoamLmThresholdEntry or
jnxSoamDmThresholdEntry.
aboveAlarm(1) indicates that the crossing type alarm was an above
threshold
setAlarm(2) indicates that the crossing type alarm was a set
threshold
clearAlarm(3) indicates that the crossing type alarm was a clear
threshold
This object is only used for the notification.ro Enumeration .1.3.6.1.4.1.2636.3.78.1.5.12 |
jnxSoamPmNotificationObjLastDateAndTimeThis object contains the time and date at the time that
the last notification event is detected, at the end of flap timer interval
and not the time of the first notification
generation.
This object is used only for notifications. The mechanism to set and keep
current the date and time is not specified.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2636.3.78.1.5.13 |
jnxSoamPmMibConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2636.3.78.2 |