INTEL-ES480-QOS-MIB
Intel ES480T Quality-of-Service objects
Main OID:
es480tQos.1.3.6.1.4.1.343.6.60.3
16
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
16 total| Object Name |
|---|
es480tQosIntel ES480T Quality-of-Service objects MODULE-IDENTITY .1.3.6.1.4.1.343.6.60.3 |
SNMPv2-SMIIntel ES480T Quality-of-Service objects Unknown .1.3.6.1.4.1.343.6.60.3 |
es480tQosCommon OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.60.3.1 |
es480tQosModeIndicates which QoS mode the device should
use. ingress(1) applies priority-based QoS based
on the incoming packet's destination IP or MAC
address, 802.1p priority, PACE(tm), Source Port or
VLAN. egress(2) applies priority- and bandwidth-based
QoS based on destination IP or MAC address or VLAN.rw Enumeration .1.3.6.1.4.1.343.6.60.3.1.4 |
es480tQosUnconfigureSetting this to true will reset all QoS settings
in the device to factory defaults. Reads from this
value return an undefined value.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.343.6.60.3.1.5 |
es480tQosProfileTableThis table lists QoS profiles. SEQUENCE OF Es480tQosProfileEntry .1.3.6.1.4.1.343.6.60.3.1.6 |
es480tQosProfileEntryAn individual QoS profile Entry. Es480tQosProfileEntry .1.3.6.1.4.1.343.6.60.3.1.6.1 |
es480tQosProfileIndexAn index that uniquely identifies an entry in the
qos table.rw INTEGER .1.3.6.1.4.1.343.6.60.3.1.6.1.1 |
es480tQosProfileNameA unique qos profile name.rw DisplayString .1.3.6.1.4.1.343.6.60.3.1.6.1.2 |
es480tQosProfileMinBwThe minumum percentage of bandwidth that this queue requires.
The Switch is required to provide the minumum amount of
bandwidth to the queue. The lowest possible value is 0%.rw INTEGER .1.3.6.1.4.1.343.6.60.3.1.6.1.3 |
es480tQosProfileMaxBwThe maximum percentage of bandwidth that this queue is
permitted to userw INTEGER .1.3.6.1.4.1.343.6.60.3.1.6.1.4 |
es480tQosProfilePriorityThe level of priority in which this queue will be serviced
by the Switch.rw Enumeration .1.3.6.1.4.1.343.6.60.3.1.6.1.5 |
es480tQosProfileRowStatusThe status of the es480tQosProfile entry.
This OBJECT can be set to:
active(1)
createAndGo(4)
createAndWait(5)
destroy(6)
The following values may be read:
active(1)
notInService(2)
notReady(3).
Setting this object to createAndGo(4) causes the agent
to attempt to create and commit the row based on
the contents of the objects in the row. If all necessary
information is present in the row and the values are
acceptible to the agent, the agent will change the
status to active(1). If any of the necessary objects
are not available, the agent will reject the creation
request.
Setting this object to createAndWait(5) causes a row
in this table to be created. The agent sets the
status to notInService(2) if all of the information is
present in the row and the values are acceptable to the
agent; otherwise, the agent sets the status to
notReady(3).
Setting this object to active(1) is only valid when
the current status is active(1) or notInService(2).
When the state of the row transitions is set to active(1),
the agent creates the corresponding row in the ifTable..
Setting this object to destroy(6) will remove the corresponding
QoS Profile Entry.
In order for a set of this object to destroy(6) to succeed,
all dependencies on this row must have been removed. These
will include any stacking dependencies in the ifStackTable and
any protocol specific tables dependencies.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.343.6.60.3.1.6.1.6 |
es480tQosByVlanMappingTableTable to associate a Vlan with the QoS profile that the
Vlan is using. Every Vlan is assigned a Qos Profile and
hence there is an entry in this table corresponding to every
entry in the es480tVlanIfTable. SEQUENCE OF Es480tQosByVlanMappingEntry .1.3.6.1.4.1.343.6.60.3.1.7 |
es480tQosByVlanMappingEntryThe QoS associated with a particular Vlan. Es480tQosByVlanMappingEntry .1.3.6.1.4.1.343.6.60.3.1.7.1 |
es480tQosByVlanMappingQosProfileIndexValue of es480tQosProfileIndex that uniquely
identifies a QoS Profile entry in es480tQosProfileTable.
This indicates the QoS to be given to traffic for this
Vlan in the absence of any other more specific
configuration information for this traffic.rw INTEGER .1.3.6.1.4.1.343.6.60.3.1.7.1.1 |