EXPRESSGS-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
377
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
377 total| Object Name |
|---|
intel OBJECT IDENTIFIER .1.3.6.1.4.1.343 |
RFC1155-SMI Unknown .1.3.6.1.4.1.343 |
mib2ext OBJECT IDENTIFIER .1.3.6.1.4.1.343.6 |
esGigaSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13 |
expressGSAgent OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.1 |
expressGSAgentGen OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.1.1 |
expressGSAgentMIBVersionThe version of the Express Gigabit Switch Enterprise Specific MIB that this agent
supports.ro DisplayString .1.3.6.1.4.1.343.6.13.1.1.1 |
expressGSAgentMgrIndexThe value of this object represents the index into the community table that
is used to authenticate SNMP requests for this manager.ro INTEGER .1.3.6.1.4.1.343.6.13.1.1.2 |
expressGSAgentCommunity OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.1.2 |
expressGSCommunityTable SEQUENCE OF ExpressGSCommunityEntry .1.3.6.1.4.1.343.6.13.1.2.1 |
expressGSCommunityEntry ExpressGSCommunityEntry .1.3.6.1.4.1.343.6.13.1.2.1.1 |
expressGSCommunityIndexAn index that uniquely identifies this entry.ro INTEGER .1.3.6.1.4.1.343.6.13.1.2.1.1.1 |
expressGSCommunityStringThe community string included in the SNMP PDU used for authentication
purposes.rw DisplayString .1.3.6.1.4.1.343.6.13.1.2.1.1.2 |
expressGSCommunityAddressTypeThe type of address associated with this community. If set to any(1), only
the community string is authenticated.rw Enumeration .1.3.6.1.4.1.343.6.13.1.2.1.1.3 |
expressGSCommunityAddressIf the address type is any, then the value of this object is a null string. If
the type is ipv4(2), then this value represents a 4 byte IP address.rw NetworkAddress .1.3.6.1.4.1.343.6.13.1.2.1.1.4 |
expressGSCommunityAccessThe MIB access supported for this community entry.
A Get or GetNext SNMP PDU is authenticated if the value of this object
is read-only(2) or read-write(3). A Set request will be honored if the value
of this object is read-write(3).
If more granular access control is desired, then the value of this object is set
to more-specific(4), and the view table should be consulted. This enables
the capability to set different access rights to different branches of the MIB
for a particular community.rw Enumeration .1.3.6.1.4.1.343.6.13.1.2.1.1.5 |
expressGSCommunityTrapReceiverIf set to enable(1), this community entry is considered a trap receiver.
When the agent generates an SNMP trap, a copy will be sent to this host
using this community string.rw Enumeration .1.3.6.1.4.1.343.6.13.1.2.1.1.6 |
expressGSCommunitySecurityLevelSecure tables are only accessible from users with security clearance. For
example, this table (the community table) is only accessible by parties that
have the security clearance.rw Enumeration .1.3.6.1.4.1.343.6.13.1.2.1.1.7 |
expressGSCommunityStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.343.6.13.1.2.1.1.8 |
expressGSAgentWeb OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.1.3 |
expressGSAgentWebServerURLThe URL of where the document server software is
installed. The switch uses this location to find online
help and bimapped graphics. Enter the host name or IP
address of the HTTP server at the HTTP Server Location
prompt, followed by ':2010'. For example, for a host
named 'phantom,', enter 'http://phantom:2010'. If no
server is desired or installed, set this object to the
empty string.rw DisplayString .1.3.6.1.4.1.343.6.13.1.3.1 |
expressGSAgentWebServerHelpDirectoryThe subdirectory that contains the help files on the
document server. Typically, this directory is 'help'.rw DisplayString .1.3.6.1.4.1.343.6.13.1.3.2 |
expressGSChassis OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3 |
expressGSChassisGen OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.1 |
expressGSChassisTypeThe model of the chassis that this agent is managing.ro Enumeration .1.3.6.1.4.1.343.6.13.3.1.1 |
expressGSChassisSlotsThe number of slots available in this chassis. If this chassis is a stackable
chassis, the total capacity of stacking units.ro INTEGER .1.3.6.1.4.1.343.6.13.3.1.2 |
expressGSInventory OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.2 |
expressGSInventoryTableA table of inventory information. SEQUENCE OF ExpressGSInventoryEntry .1.3.6.1.4.1.343.6.13.3.2.1 |
expressGSInventoryEntryInventory information related to this device. ExpressGSInventoryEntry .1.3.6.1.4.1.343.6.13.3.2.1.1 |
expressGSInventoryResourceTypeThe resource class of this inventory item.ro ResourceType .1.3.6.1.4.1.343.6.13.3.2.1.1.1 |
expressGSInventoryResourceIndexThe resource identifier of this inventory item.ro ResourceId .1.3.6.1.4.1.343.6.13.3.2.1.1.2 |
expressGSInventoryModelNumberThe model number of this device.ro DisplayString .1.3.6.1.4.1.343.6.13.3.2.1.1.3 |
expressGSInventorySerialNumberThe serial number of this device.ro DisplayString .1.3.6.1.4.1.343.6.13.3.2.1.1.4 |
expressGSInventoryVersionThe revision number of this device.ro DisplayString .1.3.6.1.4.1.343.6.13.3.2.1.1.5 |
expressGSInventoryManufactureInfoInformation related to the manufacturing of this device.ro DisplayString .1.3.6.1.4.1.343.6.13.3.2.1.1.6 |
expressGSInventoryScratchPadA scratch pad area available for keeping user-supplied inventory
information.rw DisplayString .1.3.6.1.4.1.343.6.13.3.2.1.1.7 |
expressGSPowerSystems OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.3 |
expressGSPowerSupplies OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.3.1 |
expressGSPowerSupplyTableA table of information related to each power supply in the system. SEQUENCE OF ExpressGSPowerSupplyEntry .1.3.6.1.4.1.343.6.13.3.3.1.1 |
expressGSPowerSupplyEntryAn entry providing information about a particular power supply in the
system. ExpressGSPowerSupplyEntry .1.3.6.1.4.1.343.6.13.3.3.1.1.1 |
expressGSPowerSupplyIndexAn index that uniquely identifies this power supply. This index
corresponds to the expressGSResourceIndex of the power supply type
resource.ro ResourceId .1.3.6.1.4.1.343.6.13.3.3.1.1.1.1 |
expressGSPowerSupplyTypeAn enumerated integer describing the type of power supply.ro Enumeration .1.3.6.1.4.1.343.6.13.3.3.1.1.1.2 |
expressGSPowerSupplyStatusThe status of this power supply. Okay(1) indicates the power supply is
operating properly. Faulty(2) indicates that the power supply is not
functioning properly. In this case, more information can be determined
from the other power supply attributes.ro Enumeration .1.3.6.1.4.1.343.6.13.3.3.1.1.1.3 |
expressGSPowerSupplyInputStatusThe status of the input power feed (e.g. the AC power cord) to this
power supply.ro Enumeration .1.3.6.1.4.1.343.6.13.3.3.1.1.1.4 |
expressGSPowerSupplyOutputStatusThe status of the output power from this power supply.ro Enumeration .1.3.6.1.4.1.343.6.13.3.3.1.1.1.5 |
expressGSPowerSupplyOutputCapacityThe total capacity of power supplied by this supply in Watts.ro INTEGER .1.3.6.1.4.1.343.6.13.3.3.1.1.1.6 |
expressGSPowerMgmtGen OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.3.2 |
expressGSPowerCapacityThe total capacity (in Watts) of power available (currently) in the system.ro INTEGER .1.3.6.1.4.1.343.6.13.3.3.2.1 |
expressGSPowerUsedThe total power (in Watts) currently being consumed in the system.ro INTEGER .1.3.6.1.4.1.343.6.13.3.3.2.2 |
expressGSPowerMgmtCtl OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.3.3 |
expressGSPowerControlTableThis table manages the power attributes associated with each module. SEQUENCE OF ExpressGSPowerControlEntry .1.3.6.1.4.1.343.6.13.3.3.3.1 |
expressGSPowerControlEntryAn entry in the power control table manages the power attributes of the
specified module. ExpressGSPowerControlEntry .1.3.6.1.4.1.343.6.13.3.3.3.1.1 |
expressGSPowerControlUsedThe total power (in Watts) used by this module.ro INTEGER .1.3.6.1.4.1.343.6.13.3.3.3.1.1.1 |
expressGSPowerControlPriorityThe priority of this module to be considered in the event of a power
supply failure where the amount of power used exceeds the system
capacity. Low priority modules will be powered down before higher
priority modules.rw Enumeration .1.3.6.1.4.1.343.6.13.3.3.3.1.1.2 |
expressGSPowerControlModeNormally, a module power mode is enable(1).
In the event of a power supply failure resulting in a power shortage, or in
the event of this module being inserted without enough available power,
the mode will be poweredDown(3). Setting this object to the value of
poweredDown(3) will result in an error.
When enough power is available, the module will power back up when in
this mode. A module may be powered down through administrative
action by setting the value of this object to disable(2). In this mode, the
module will remain powered down until the mode is set back to enable.rw Enumeration .1.3.6.1.4.1.343.6.13.3.3.3.1.1.3 |
expressGSTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.4 |
expressGSTempTableA table of information related to the temperature within the system. SEQUENCE OF ExpressGSTempEntry .1.3.6.1.4.1.343.6.13.3.4.1 |
expressGSTempEntryAn entry providing temperature information related to a specific
temperature probe in the system. ExpressGSTempEntry .1.3.6.1.4.1.343.6.13.3.4.1.1 |
expressGSTempIndexA unique index that identifies this temperature probe. This index
corresponds to the expressGSResourceIndex for temperature probe type
resources.ro ResourceId .1.3.6.1.4.1.343.6.13.3.4.1.1.1 |
expressGSTempValueThe current temperature reading of this temperature probe in degrees
Celsius.ro INTEGER .1.3.6.1.4.1.343.6.13.3.4.1.1.2 |
expressGSTempUpperLimitThe upper temperature limit of this temperature probe in degrees
Celsius.rw INTEGER .1.3.6.1.4.1.343.6.13.3.4.1.1.3 |
expressGSTempUpperWarningThe upper temperature warning of this temperature probe in degrees
Celsius.rw INTEGER .1.3.6.1.4.1.343.6.13.3.4.1.1.4 |
expressGSTempLowerWarningThe lower temperature warning of this temperature probe in degrees
Celsius.rw INTEGER .1.3.6.1.4.1.343.6.13.3.4.1.1.5 |
expressGSTempLowerLimitThe lower temperature limit of this temperature probe in degrees
Celsius.rw INTEGER .1.3.6.1.4.1.343.6.13.3.4.1.1.6 |
expressGSModules OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.5 |
expressGSModuleTableA table of information related to the modules in the system. SEQUENCE OF ExpressGSModuleEntry .1.3.6.1.4.1.343.6.13.3.5.1 |
expressGSModuleEntryAttributes related to managing this module. ExpressGSModuleEntry .1.3.6.1.4.1.343.6.13.3.5.1.1 |
expressGSModuleIndexAn index that uniquely identifies this module. This index corresponds to
the expressGSResourceIndex associated with module type resources.ro ResourceId .1.3.6.1.4.1.343.6.13.3.5.1.1.1 |
expressGSModuleNameA user-assignable name for this module.rw DisplayString .1.3.6.1.4.1.343.6.13.3.5.1.1.2 |
expressGSModuleTypeAn enumerated integer that is unique for each module model.ro Enumeration .1.3.6.1.4.1.343.6.13.3.5.1.1.3 |
expressGSModuleBaseTypeThe base type of this module. This object is used to describe the core
functions of the module. Often, base designs are derived into multiple
module types which are typically just packaging variations (e.g. changing the
connector types). The value of this object corresponds to the value of
expressGSResourceBaseType.ro Enumeration .1.3.6.1.4.1.343.6.13.3.5.1.1.4 |
expressGSModuleSlotWidthThe number of slots that this module occupies.ro INTEGER .1.3.6.1.4.1.343.6.13.3.5.1.1.5 |
expressGSModuleSlotOffsetThe slot offset (one based) that identifies, along with the slot width and
slot location, the actual slots that this module occupies. The offset identifies
which slot within the width of the module that this module reports as its
slot number.ro INTEGER .1.3.6.1.4.1.343.6.13.3.5.1.1.6 |
expressGSModulePortsThe total number of ports associated with this module.ro INTEGER .1.3.6.1.4.1.343.6.13.3.5.1.1.7 |
expressGSPorts OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6 |
expressGSPortMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.1 |
expressGSPortTableA table of information related to every data port in this data networking
system. SEQUENCE OF ExpressGSPortEntry .1.3.6.1.4.1.343.6.13.3.6.1.1 |
expressGSPortEntryA data port associated with this data networking system. ExpressGSPortEntry .1.3.6.1.4.1.343.6.13.3.6.1.1.1 |
expressGSPortIndexAn index that uniquely identifies this port. Typically, ports are child
resources of the module that contains them. In these cases, ports are
identified by their module and their relative physical position on that
module.ro ResourceId .1.3.6.1.4.1.343.6.13.3.6.1.1.1.1 |
expressGSPortNameThe user-assigned name for this port.
Note that setting this object for an internal(1) port results in an error.rw DisplayString .1.3.6.1.4.1.343.6.13.3.6.1.1.1.2 |
expressGSPortTypeAn internal(1) port does not have an external connection.
An ether-ten-oneHundred(2) port is an Ethernet port which can be switched between
10 and 100 megabits per second.
An ether-oneHundred(3) port is a 100 megabits per second Fast Ethernet port.
An ether-gigabit(4) port is a 1000 megabits per second Gigabit Ethernet port.ro Enumeration .1.3.6.1.4.1.343.6.13.3.6.1.1.1.3 |
expressGSPortBaseTypeThe base type of this port. This object may be useful to help manage new
port types that are similar in nature to legacy port types.ro Enumeration .1.3.6.1.4.1.343.6.13.3.6.1.1.1.4 |
expressGSPortModeThe mode of this port. When set to enable(1), this port passes data.
When set to disable(2), the port does not receive or transmit data, nor does
it generate port-level signaling e.g. link integrity pulses.
Note that setting an internal(1) port to disable(2) results in an error.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.1.1.1.5 |
expressGSPortStatusThe status of this port. Disabled(1) means that this port has been disabled
through management action. Okay(2) indicates that this port is operating
properly. Warning(3) indicates that this port is encountering an abnormal
condition that, however, allows it to continue to pass data. LinkFailure(5)
means that this port is unable to pass data.ro Enumeration .1.3.6.1.4.1.343.6.13.3.6.1.1.1.6 |
expressGSPortConnectorThe connector type associated with this port.ro Enumeration .1.3.6.1.4.1.343.6.13.3.6.1.1.1.7 |
expressGSPortSpeedStateThe data rate of this port in bits per second. For example, a standard
Ethernet port (e.g. 10BASE-T) would indicate a value of ten-megabits-per-second((1)
indicating that the port supports a data rate of 10Mb/s. For ports that can
change their data rate (e.g. 10/100 ports), the value of this object indicates
the current state of the port's speed capability.ro Enumeration .1.3.6.1.4.1.343.6.13.3.6.1.1.1.8 |
expressGSPortDuplexStateThe value of this object indicates whether this port is operating in full- or
half-duplex mode.
The value under-negotiation(3) indicates that the port has not selected an
operational duplex setting yet.ro Enumeration .1.3.6.1.4.1.343.6.13.3.6.1.1.1.9 |
expressGSPortGroupBindingEach port is associated with a port group. Typically, a port will belong to
a port group of one and the value of this object will be the same as the
port index for this instance. That is, this port will point to itself.
The intent of this object is to help manage ports that have hierarchical
relationships. For example, an ATM port typically has a physical port and
multiple logical ports (e.g. each logical port corresponding to an instance of
an emulated LAN). In this case, each LANE instance would refer to the
instance of the physical port associated with the ATM front-end.
Another example is an FDDI DAS type port. In this case, there is a logical
port associated with the FDDI switch port which is connected to the two
FDDI physical port connectors. The physical FDDI ports both point to
the logical instance of an FDDI port.ro ResourceId .1.3.6.1.4.1.343.6.13.3.6.1.1.1.10 |
expressGSPortFlowControlMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.2 |
expressGSPortFlowControlTableA table of ports that support flow control. SEQUENCE OF ExpressGSPortFlowControlEntry .1.3.6.1.4.1.343.6.13.3.6.2.1 |
expressGSPortFlowControlEntryConfiguration objects related to port based flow control. ExpressGSPortFlowControlEntry .1.3.6.1.4.1.343.6.13.3.6.2.1.1 |
expressGSPortFlowControlModeFlow control is used to prevent or reduce the dropping of frames due to
the lack of buffer space. Overall, networks are more efficient when a
sending station is asked to pause in its sending process, rather than having
the transmitted frames dropped.
Flow control is not as efficient when used in conjunction with a shared
ports, i.e. when used with a repeater. Therefore, flow control is not
recommended for a port connected to shared topologies.
Flow control is most effective when the port is directly connected to an
end-station, especially when connected to a server. Flow control is
recommended for ports connected directly to end-stations.
When the port is in half-duplex mode, back pressure is used to control
the incoming flow. Back pressure essentially forces collisions for short
periods of time.
When the port is in full-duplex mode, IEEE 802.3 standard pause frames
are used to control the incoming flow.
Note that setting an ether-gigabit(4) port to enable-with-aggressive-backoff(3)
results in an error.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.2.1.1.21 |
expressGSPortDuplexMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.3 |
expressGSPortDuplexTableA table of ports that support full- and half-duplex data communications. SEQUENCE OF ExpressGSPortDuplexEntry .1.3.6.1.4.1.343.6.13.3.6.3.1 |
expressGSPortDuplexEntryA port device configuration that controls the duplex mode of this port. ExpressGSPortDuplexEntry .1.3.6.1.4.1.343.6.13.3.6.3.1.1 |
expressGSPortDuplexModeA point-to-point Ethernet port may be configured to support half or full
duplex communications.
A full-duplex(2) port transmits and receives data concurrently, effectively
doubling the data rate of the port.
Half-duplex(1) ports transmit or receive data, but not at the same time.
Half-duplex ports use CSMA/CD as the access method to the network.
Ports that are connected to shared segments (i.e. connected to a repeater),
should always be configured to be in half-duplex mode.
This object indicates the desired duplexity of this port. If
auto-negotiation is turned on for this port, then this value is ignored.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.3.1.1.31 |
expressGSPortSpeedMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.4 |
expressGSPortSpeedTableA table of port devices that support multiple speeds. SEQUENCE OF ExpressGSPortSpeedEntry .1.3.6.1.4.1.343.6.13.3.6.4.1 |
expressGSPortSpeedEntryA port that supports multiple speeds. ExpressGSPortSpeedEntry .1.3.6.1.4.1.343.6.13.3.6.4.1.1 |
expressGSPortSpeedModeSome of these values may not be applicable to certain types of ports.
This object indicates the desired data rate of this port. If
auto-negotiation is turned on for this port, then this value is ignored.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.4.1.1.41 |
expressGSPortAutoNegotiationMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.5 |
expressGSPortAutoNegotiationTableA table of ports that support auto-negotiation. SEQUENCE OF ExpressGSPortAutoNegotiationEntry .1.3.6.1.4.1.343.6.13.3.6.5.1 |
expressGSPortAutoNegotiationEntryAttributes associated with a port that supports auto-negotiation. ExpressGSPortAutoNegotiationEntry .1.3.6.1.4.1.343.6.13.3.6.5.1.1 |
expressGSPortAutoNegotiationModeSetting this object to autoNegotiate(1) causes this port to negotiate the
duplex mode and the port speed, subject to the port's capabilities.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.5.1.1.51 |
expressGSPortAutoNegotiationSpeedAdvertisementThe speed to advertise while auto-negotiating.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.5.1.1.52 |
expressGSPortAutoNegotiationDuplexAdvertisementThe duplexity to advertise while auto-negotiating.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.5.1.1.53 |
expressGSPortRateLimitMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.6 |
expressGSPortRateLimitTableA table of ports that support the ability to limit the rate of floods. SEQUENCE OF ExpressGSPortRateLimitEntry .1.3.6.1.4.1.343.6.13.3.6.6.1 |
expressGSPortRateLimitEntryThe rate limit configuration associated with this port. ExpressGSPortRateLimitEntry .1.3.6.1.4.1.343.6.13.3.6.6.1.1 |
expressGSPortRateLimitModeThis object configures whether rate limiting is enabled for this port (the
factory default is enable(1)). Enabling rate limiting for this port prevents
floods from overwhelming the output buffer associated with this port.
Normally, rate limiting will only consider frames that are flooded to this
port. This typically does not include known multicasts. However, known
multicasts can be included in the flood limiting by setting the value of this
object to enableIncludeKnownMulticast(3).rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.6.1.1.61 |
expressGSPortRateLimitRateThe percentage of the port's transmitted data allowed to be floods (or floods
and known multicasts). For example, the factory default setting of
twenty-percent(4) indicates that 20% of the data rate can be floods. For 10 Mb/s
ports, this is equivalent to a maximum rate of approximately 3000 flooded pps;
for 100 Mb/s ports, a maximum rate of approximately 30,000 flooded pps.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.6.1.1.62 |
expressGSPortRateLimitBurstSizeThe maximum number of consecutive transmitted flooded (or flooded and known
multicasted) packets. Typically, the burst size is set so as to not overflow the
port's buffer.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.6.1.1.63 |
expressGSPortPacePriorityMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.7 |
expressGSPortPacePriorityTableA table of ports that support the ability to classify frame priority based on
3Com Pace(r) Prioritization. SEQUENCE OF ExpressGSPortPacePriorityEntry .1.3.6.1.4.1.343.6.13.3.6.7.1 |
expressGSPortPacePriorityEntryA port that supports 3Com Pace(r) priority. ExpressGSPortPacePriorityEntry .1.3.6.1.4.1.343.6.13.3.6.7.1.1 |
expressGSPortPacePriorityModeWhen Pace priority is enabled, this port will detect frames that use 3Com
Corporation's Pace(r) Priority signaling. Frames signaled with priority in
this manner are mapped to traffic priority level 4 (on scale of 0-7).rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.7.1.1.71 |
expressGSPortCategoryMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.6.8 |
expressGSPortCategoryTableA table of ports that support the port category feature. Currently, all
ports support this capability. SEQUENCE OF ExpressGSPortCategoryEntry .1.3.6.1.4.1.343.6.13.3.6.8.1 |
expressGSPortCategoryEntryA port that supports port categorization. ExpressGSPortCategoryEntry .1.3.6.1.4.1.343.6.13.3.6.8.1.1 |
expressGSPortCategoryModeBy default, all ports are considered service ports. A
service port is a port that provides a networks service
such as a connection to a server, other switches, or
the like. A service port will trigger the service port
event for status changes with the alarm severity and
will trigger an alarm in the alarm table on link
failure.
In contrast, user ports trigger the user link event
with warning severity. They do not trigger an alarm
upon link failures. User ports are useful to prevent
floods of traps or entries in the alarm table. This is
especially true for ports connected to user hosts that
power up in the morning and power down again at the end
of the work day.rw Enumeration .1.3.6.1.4.1.343.6.13.3.6.8.1.1.81 |
expressGSBufferMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.3.7 |
expressGSBufferTableA table of frame buffers in the system. SEQUENCE OF ExpressGSBufferEntry .1.3.6.1.4.1.343.6.13.3.7.1 |
expressGSBufferEntryObjects related to the management of this frame buffer. ExpressGSBufferEntry .1.3.6.1.4.1.343.6.13.3.7.1.1 |
expressGSBufferIndexThe unique index that identifies this buffer within the system. Buffers are
indexed first by their module association and then a unique index within
that module.ro ResourceId .1.3.6.1.4.1.343.6.13.3.7.1.1.1 |
expressGSBufferFabricPortThe switch fabric port associated with this buffer.ro ResourceId .1.3.6.1.4.1.343.6.13.3.7.1.1.2 |
expressGSBufferFabricPortDirectionThe value of this object indicates whether the buffer is used for buffering
frames going into the switching fabric or coming out of the fabric.ro Enumeration .1.3.6.1.4.1.343.6.13.3.7.1.1.3 |
expressGSBufferSwitchPortThe switch port associated with this frame buffer. Some buffers are not
associated with any one switch port. In those cases, the value of the
resource ID returned will be the null resource ID.ro ResourceId .1.3.6.1.4.1.343.6.13.3.7.1.1.4 |
expressGSBufferMemoryThe amount of memory available for frame buffering in Kilobytes (KB).ro INTEGER .1.3.6.1.4.1.343.6.13.3.7.1.1.5 |
expressGSBufferAgeTimerConfigures the timer used for aging frames in this buffer. If the timer
expires for a frame, the frame is dropped and the event is counted in the
stale drop counter. By default, the age timer is set to a 0.25 seconds
(quarter of a second).
The actual time that a frame may be aged out may vary. When set to a
quarter of a second (250ms), the actual time may vary between 160ms and
320ms. When set to a second (1000ms), the time may vary between 640ms
and 1.28 seconds (1028ms).rw Enumeration .1.3.6.1.4.1.343.6.13.3.7.1.1.6 |
expressGSBufferPriorityServicingThe value of this object configures how often the normal priority queue is
serviced relative to the high priority queue. By default, the normal priority
queue is serviced every thousand frames(3). This means that the normal
priority queue is guaranteed to be serviced after servicing, at most, one
thousand high priority frames.
It is important to service the normal priority queue for two reasons. One is
to prevent starvation for frames on the normal priority queue. The other
reason is that frames cannot be aged if they are not serviced (see the age
timer).rw Enumeration .1.3.6.1.4.1.343.6.13.3.7.1.1.7 |
expressGSBufferPriorityAllocationThis object controls how much of the total buffer space should be
allocated to high priority queue. Please be warned that setting this object to
a different value causes the associated buffer to reset, causing a short loss of
data.
Setting the value of this object to none(1) not only allocates the entire buffer
space to normal traffic, but also has the side effect of disabling the priority
threshold. In other words, all traffic will be considered as normal priority
traffic.rw Enumeration .1.3.6.1.4.1.343.6.13.3.7.1.1.8 |
expressGSBufferPriorityThresholdThis object configures the threshold for which frames are considered high
priority. Frames may have a priority classification ranging from 0-7, 7
being the highest. By default, every frame that has priority 4 (four(5)) or
above is considered a high priority frame and is buffered accordingly.
If this buffer does not have any buffer space allocated for high priority
frames, then the buffer threshold will be none(1). Setting this object to a
different value without allocating buffer space to high priority traffic will
result in an error.rw Enumeration .1.3.6.1.4.1.343.6.13.3.7.1.1.9 |
expressGSBufferCongestionThis object indicates whether this buffer is in a congested state..ro Enumeration .1.3.6.1.4.1.343.6.13.3.7.1.1.10 |
expressGSBufferHighOverflowDropsThe count of the number of high priority frames dropped due to the high
priority queue overflowing.ro Counter .1.3.6.1.4.1.343.6.13.3.7.1.1.11 |
expressGSBufferLowOverflowDropsThe count of the number of low priority frames dropped due to the low
priority queue overflowing.ro Counter .1.3.6.1.4.1.343.6.13.3.7.1.1.12 |
expressGSBufferHighStaleDropsThe count of the number of high priority frames dropped due to being in
the high priority queue too long (the frame aged out).ro Counter .1.3.6.1.4.1.343.6.13.3.7.1.1.13 |
expressGSBufferLowStaleDropsThe count of the number of low priority frames dropped due to being in
the low priority queue too long (the frame aged out).ro Counter .1.3.6.1.4.1.343.6.13.3.7.1.1.14 |
expressGSBufferCongestionDropsThe count of the number of frames dropped due to the destination
(output) buffer being congested.ro Counter .1.3.6.1.4.1.343.6.13.3.7.1.1.16 |
expressGSSwitching OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5 |
expressGSSwitchingLayerII OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1 |
expressGSSwitchGen OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.1 |
expressGSSwitchSTPConfigWhen set to ieee8021dStp(1), the switch executes spanning tree conformant
to the IEEE 802.1D bridging standard. The switch runs one instance of
spanning tree.
When set to stpPerVlan(2), the switch executes a separate instance of spanning
tree for each virtual LAN. This configuration conforms to the model that
instances of virtual LANs within the switch are separate virtual bridging
functions. This method may not work well with bridge/routers that are also
running spanning tree.
When set to twoLayerStp(3), the switch executes a two-layer spanning tree to prevent loops. Two layer
spanning tree creates a higher 'plane' of spanning tree between VLAN devices. This method of running
spanning tree is 'plug and play' with bridge/router type devices and also scales better than the other
two methods for large environments.
When set to disable(4), spanning tree is disabled in the switch.rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.1.1 |
expressGSSwitchAgingTimeThe timeout period in seconds for aging dynamically learned forwarding
information. A default of 300 seconds is recommended. An aged entry is
marked invalid, but is not removed from the Address Forwarding Table,
because it is assumed that it will be relearned to the same location within
the table.rw INTEGER .1.3.6.1.4.1.343.6.13.5.1.1.2 |
expressGSSwitchSuperAgingTimeThe timeout period in days for removing stale invalid entries from the Address
Forwarding Table. A superaged entry is removed completely from the Address
Forwarding Table, because it is assumed that the entry will never be relearned.rw INTEGER .1.3.6.1.4.1.343.6.13.5.1.1.3 |
expressGSBridgeMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.2 |
expressGSBridgeTableA table of Spanning Tree information for every bridge in the system. SEQUENCE OF ExpressGSBridgeEntry .1.3.6.1.4.1.343.6.13.5.1.2.1 |
expressGSBridgeEntry ExpressGSBridgeEntry .1.3.6.1.4.1.343.6.13.5.1.2.1.1 |
expressGSBridgeIndexAn index that uniquely identifies this bridge.ro ResourceId .1.3.6.1.4.1.343.6.13.5.1.2.1.1.1 |
expressGSBridgeTypeIndicates whether this is a legacy dot1d bridge consisting of all switch
ports or a virtual bridge consisting of all virtual subports for a particular
Vlan.ro Enumeration .1.3.6.1.4.1.343.6.13.5.1.2.1.1.2 |
expressGSBridgeModeUsed to enable or disable Spanning Tree for this bridge. When set to
disable(2), all BPDUs are forwarded like regular multicast packets. The
default value is enable(1).rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.2.1.1.3 |
expressGSBridgeStatusThe enable/disable status of this bridge. This object incorporates the
setting of the expressGSSwitchSTPConfig object. When
expressGSSwitchSTPConfig is set such that this bridge will not be active,
expressGSBridgeStatus returns disabled(2). If expressGSSwitchSTPConfig is set
such that this bridge will be active, and expressGSBridgeMode is enable(1), this
object returns enabled(2).ro Enumeration .1.3.6.1.4.1.343.6.13.5.1.2.1.1.4 |
expressGSBridgeStpPriorityThe priority value of the Bridge Identifier. See dot1dStpPriority.rw INTEGER .1.3.6.1.4.1.343.6.13.5.1.2.1.1.5 |
expressGSBridgeStpTimeSinceTopologyChangeThe time since the last topology change was detected. See
dot1dStpTimeSinceTopologyChange.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.343.6.13.5.1.2.1.1.6 |
expressGSBridgeStpTopChangesThe total number of topology changes. See dot1dStpTopChangesro Counter .1.3.6.1.4.1.343.6.13.5.1.2.1.1.7 |
expressGSBridgeStpDesignatedRootThe bridge considered to be root by this node. See
dot1dStpDesignatedRoot.ro BridgeId .1.3.6.1.4.1.343.6.13.5.1.2.1.1.8 |
expressGSBridgeStpRootCostThe cost of the path to the root from this node. See dot1dStpRootCost.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.2.1.1.9 |
expressGSBridgeStpRootPortThe port number with the lowest cost path to the root bridge. See
dot1dStpRootPort.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.2.1.1.10 |
expressGSBridgeStpMaxAgeThe maximum age used by this bridge to hold onto STP information
before discarding. See dot1dStpMaxAge.ro Timeout .1.3.6.1.4.1.343.6.13.5.1.2.1.1.11 |
expressGSBridgeStpHelloTimeThe amount of time between configuration BPDUs. See
dot1dStpHelloTime.ro Timeout .1.3.6.1.4.1.343.6.13.5.1.2.1.1.12 |
expressGSBridgeStpHoldTimeThe time value that indicates the interval during which no more than two
configuration BPDUs will be sent by this node. See dot1dStpHoldTime.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.2.1.1.13 |
expressGSBridgeStpForwardDelayThe amount of time that this node stays in each of the Listening and
Learning states. See dot1dStpForwardDelay.ro Timeout .1.3.6.1.4.1.343.6.13.5.1.2.1.1.14 |
expressGSBridgeStpBridgeMaxAgeThe value of MaxAge when this bridge is the root. See
dot1dStpBridgeMaxAge.rw Timeout .1.3.6.1.4.1.343.6.13.5.1.2.1.1.15 |
expressGSBridgeStpBridgeHelloTimeThe value of HelloTime to use when this bridge is the root. See
dot1dStpBridgeHelloTime.rw Timeout .1.3.6.1.4.1.343.6.13.5.1.2.1.1.16 |
expressGSBridgeStpBridgeForwardDelayThe value of FowardDelay to use when this bridge is the root. See
dot1dStpBridgeForwardDelay.rw Timeout .1.3.6.1.4.1.343.6.13.5.1.2.1.1.17 |
expressGSBridgePortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.3 |
expressGSBridgePortTableA table of Spanning Tree information for every port that supports
Spanning Tree in every bridge in the system SEQUENCE OF ExpressGSBridgePortEntry .1.3.6.1.4.1.343.6.13.5.1.3.1 |
expressGSBridgePortEntry ExpressGSBridgePortEntry .1.3.6.1.4.1.343.6.13.5.1.3.1.1 |
expressGSBridgePortIndexAn index that uniquely identifies this bridge port. This index corresponds
to the expressGSResourceIndex for bridge port type resources.ro ResourceId .1.3.6.1.4.1.343.6.13.5.1.3.1.1.1 |
expressGSBridgePortPriorityThe value of the priority field in the port ID. See dot1dStpPortPriority.
The default value is 128.rw INTEGER .1.3.6.1.4.1.343.6.13.5.1.3.1.1.2 |
expressGSBridgePortStateThe port's current state as defined by the Spanning Tree Protocol. See
dot1dStpPortState.
The virtual port is considered broken if its switch port is blocked.ro Enumeration .1.3.6.1.4.1.343.6.13.5.1.3.1.1.3 |
expressGSBridgePortEnableThe enabled/disabled status of this port. See dot1dStpPortEnable. The
default is enabled(2).rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.3.1.1.4 |
expressGSBridgePortPathCostThe contribution of this port to the path cost of the paths towards the
spanning tree root. See dot1dStpPortPathCost. The default value is
dependent on the port speed, trunking mode, and duplexity.rw INTEGER .1.3.6.1.4.1.343.6.13.5.1.3.1.1.5 |
expressGSBridgePortDesignatedRootThe bridge recorded as root for this port's segment. See
dot1dStpPortDesignatedRoot.ro BridgeId .1.3.6.1.4.1.343.6.13.5.1.3.1.1.6 |
expressGSBridgePortDesignatedCostThe path cost of the designated root of the segment connected to this
port. See dot1dStpPortDesignatedCost.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.3.1.1.7 |
expressGSBridgePortDesignatedBridgeThe bridge identifier of the bridge that is considered the designated bridge
for this port's segment. See dot1dStpPortDesignatedBridge.ro BridgeId .1.3.6.1.4.1.343.6.13.5.1.3.1.1.8 |
expressGSBridgePortDesignatedPortThe port identifier of the port on the Designated Bridge for this port's
segment. See dot1dStpPortDesignatedPort.ro OCTET STRING .1.3.6.1.4.1.343.6.13.5.1.3.1.1.9 |
expressGSBridgePortForwardTransitionsThe number of times this port has transitioned from the learning state to
the forwarding state. See dot1dStpPortForwardTransitions.ro Counter .1.3.6.1.4.1.343.6.13.5.1.3.1.1.10 |
expressGSBridgePortFastStartThis object is being replaced by the switch port object expressGSSwitchPortFastStart.
When this bridge port object is set to enable(1), the bridge port and all other
bridge ports on the same switch port, transition right from blocking to forwarding,
skipping the listening and learning states. When this bridge port object is set
to disable(2), the bridge port and all other bridge ports on the same switch port
have this option disabled. The user should be warned that using the fast start
feature greatly increases the likelihood of unintended network loops that would
otherwise be prevented by participating in the normal spanning tree algorithm.
The factory default value for this object is disable(2).rwdeprecated Enumeration .1.3.6.1.4.1.343.6.13.5.1.3.1.1.11 |
expressGSBridgePortSetDefaultWhen set to setDefault(2), the expressGSBridgePortPriority,
expressGSBridgePortEnable, and expressGSBridgePortPathCost
will be set to the factory default values.rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.3.1.1.12 |
expressGSBridgePortEnableChangeDetectionWhen this object is set to enable(1), a Topology Change Notification
will be generated when this port goes to Blocking or Forwarding (if
the port is a designated port). When set to disable(2), no
Topology Change Notification will be generated for this port. The
default is enable(1).rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.3.1.1.13 |
expressGSL2AddrMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.4 |
expressGSL2AddrDatabaseMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.4.1 |
expressGSL2AddressTableA table of address table entries. The address table is used by the bridging
function to perform forwarding and filtering decisions. An address may
appear multiple times in different entries corresponding to the different
logical address tables. SEQUENCE OF ExpressGSL2AddressEntry .1.3.6.1.4.1.343.6.13.5.1.4.1.1 |
expressGSL2AddressEntryA particular address table entry. ExpressGSL2AddressEntry .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1 |
expressGSL2AddressIndexAn index that uniquely identifies this address entry.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.1 |
expressGSL2AddressTableIndexThe address table that this entry is associated with.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.2 |
expressGSL2AddressMacAddressThe IEEE 802 MAC Address associated with this database entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.3 |
expressGSL2AddressPortBindingThe switch port that this address is associated with.rw ResourceId .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.4 |
expressGSL2AddressBindingValidThe port binding of an address entry is aged out in conformance with the
specifications laid out in the IEEE 802.1D standard. When the address is
aged out, the port binding becomes invalid.ro Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.5 |
expressGSL2AddressVlanIDThe VLAN ID of the VLAN that this address entry corresponds to.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.6 |
expressGSL2AddressPriorityIf set to high(2), frames destined to this address are classified with priority
value 4.rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.7 |
expressGSL2AddressForwardWhen set to specialDelivery(2), frames sent to this address are treated to
special delivery where the spanning tree state of the inbound port is
ignored. Typically, special delivery is only used for Bridge PDUs such as
spanning tree frames.ro Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.8 |
expressGSL2AddressCopyIt is sometimes useful for the switch processor to eavesdrop on traffic to
certain destinations. This is especially useful in supporting the intelligent
multicasting function.ro Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.9 |
expressGSL2AddressPersistenceThis object indicates the persistence of this entry:
other(1) - This entry is currently in use but the conditions under which it
will remain so are different from each of the following values.
invalid(2) - Writing this value to the object removes the corresponding
entry.
permanent(3) - Address is not aged out. Additionally, if the address is seen
as a source on a different port for this VLAN, the frame is filtered and the
filter event is counted. Static address entries are stored in non-volatile
memory and are restored to the address table following each system reset.
deleteOnReset(4) - Indicates that the entry is not aged out, however the
entry is not stored in non-volatile memory. Therefore, when the device is
reset, the entry will not be restored.
deleteOnTimeout(5) - Typically, address entries are learned dynamically by
the switch. These entries are aged out of the table if they are not active on
the network. This value
correlates to this state.rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.10 |
expressGSL2AddressStatusThis object indicates the status of the entry:
other(1) - None of the following.
learned(2) - This entry was learned dynamically.
self(3) - The value of the corresponding instance of
expressGSAddressMacAddress represents one of the bridge's addresses.
mgmt(4) - This entry was added or modified by management. Entries
that have been added by management and made permanentro Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.1.1.1.11 |
expressGSL2AddrSummaryMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.4.2 |
expressGSL2AddrSummaryTableThis summary table packs the address entries in the address database into
summary objects. The goal is to optimize the upload of the large amount
of data stored therein.
Typically, a management station would use getNext requests to retrieve the
next logical summary object. The returned object value contains the next n
entries of the address database packed into one PDU. The instance of the
object returned is the index of the last address entry packed in the
summary, thereby optimizing for the next getNext request.
[ Fix this? What about gets?] SEQUENCE OF ExpressGSL2AddrSummaryEntry .1.3.6.1.4.1.343.6.13.5.1.4.2.1 |
expressGSL2AddrSummaryEntryA summary object that packs as many address entries possible into a
summary object. ExpressGSL2AddrSummaryEntry .1.3.6.1.4.1.343.6.13.5.1.4.2.1.1 |
expressGSL2AddrSummaryThe value of this object is a packed opaque structure representing an array
of address entries. The format of this structure is:
struct L2AddressEntry {
UNS32 index;
UNS8 addr[6]; // mac address
UNS8 fabricPort; //fabricPort and subPort == expressGSL2AddressPortBinding
UNS8 subPort;
UNS16 vlanID, //the global vlan id
UNS8 portBindingValidFlag;
UNS8 addressForwardFlag;
UNS8 addressCopyFlag;
UNS8 addressPersistence;
UNS8 addressStatus;
};
struct L2AddressSummary{
UNS8 numberOfEntries; // Number of entries that follow
UNS8 version; // version == 1
UNS16 endianFlag;
L2AddressEntry entryArray[numberOfEntries];
};ro OCTET STRING .1.3.6.1.4.1.343.6.13.5.1.4.2.1.1.1 |
expressGSL2AddrControlMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.4.3 |
expressGSL2AddressControlTableThis table provides the network manager the ability to create new, static
address entries. Entries added through this table are added to the specified
address table as a static entry and are save in non-volatile memory for
reconfiguration upon system restart.
This table is indexed by the expressGSAgentMgrIndex value which provides a
separate instance for each manager. SEQUENCE OF ExpressGSL2AddressControlEntry .1.3.6.1.4.1.343.6.13.5.1.4.3.1 |
expressGSL2AddressControlEntryA control entry enables this manager to add a new entry to the specified
address table. When the entry is written to, the control index value is reset
to 0. When the actual entry is created, the index value will read as non-zero,
reporting the actual entry created. ExpressGSL2AddressControlEntry .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1 |
expressGSL2AddressControlIndexThe index of the address entry that was created for this address.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1.1 |
expressGSL2AddressControlMacAddressThe IEEE 802 MAC Address associated with this database entry.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1.2 |
expressGSL2AddressControlPortBindingThe port to bind this address to.rw ResourceId .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1.3 |
expressGSL2AddressControlVlanIDThe VLAN ID of the VLAN to bind this address to.rw INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1.4 |
expressGSL2AddressControlPriorityIf set to high(2), frames destined to this address are classified with priority
value 4.rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1.5 |
expressGSL2AddressControlPersistenceThe persistence of the entry to be created:
permanent(1) - Address is not aged out. Additionally, if the address is seen
as a source on a different port for this VLAN, the frame is filtered and the
filter event is counted. Static address entries are stored in non-volatile
memory and are restored to the address table following each system reset.
deleteOnReset(2) - Indicates that the entry is not to be aged, however the
entry is not stored in non-volatile memory. Therefore, when the device is
reset, the entry will not be restored.
deleteOnTimeout(3) - Indicates that the entry is to be aged by the normal
aging process.rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1.6 |
expressGSL2AddressControlStatusThe status of an entry to be created. When adding an entry all fields will
be set, and then the control status is set to createRequest(1), indicating that
the entry is to be created. During creation, the status will be
underCreation(2). If the creation is successful, then the status will be set to
success(3), and the value of expressGSAddressControlIndex indicates the index
of the entry that was created in the address table. Otherwise if the creation
was not successful, then one of the following error codes will be set and
the entry will not be created:
otherError(4) - An error other then the others defined.
entryExistsError(5) - An entry already exists with this MAC address in this
address table.
invalidMacAddress(6) - Cannot create an entry with this MAC address.
invalidTableIndex(7) - The table does not exist.
invalidPortBinding(8) - The port binding is invalid.
invalidVlanID(9) - The VLAN ID is invalid.
Note that the only value that is valid to write to this object is
createRequest(1), and that this object will never return the value
createRequest(1).rw Enumeration .1.3.6.1.4.1.343.6.13.5.1.4.3.1.1.7 |
expressGSL2AddrChangeMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.1.4.4 |
expressGSL2AddressChangeLastThe index of the last entry written to the address change tablero INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.4.1 |
expressGSL2AddressChangeWrapsThe count of the number of times the address change table has wrapped.ro Counter .1.3.6.1.4.1.343.6.13.5.1.4.4.2 |
expressGSL2AddressChangeMaxEntriesThe maximum number of entries in the address change table.rw INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.4.3 |
expressGSL2AddressChangeTable. SEQUENCE OF ExpressGSL2AddressChangeEntry .1.3.6.1.4.1.343.6.13.5.1.4.4.4 |
expressGSL2AddressChangeEntryThe address change table provides a quick way of getting only the entries
that have recently changed. Since entries age out as part of the normal
switching process, entries that have aged (i.e. their destination bindings are
no longer valid) are not considered to be changed. Any other modification
to the entry, including deletion or creation, are considered to be changes.
The address change table is considered a circular table. When an entry
changes, it is added to the next position within the table. If the 'next'
position goes beyond the end of the table, the 'next' position is set to the
beginning of the table (1) and the wrap counter
(expressGSAddressChangeWraps) is incremented. The
expressGSAddressChangeLast value is updated with the index of the last
entered entry.
An entry may be in the table multiple times if it has changed multiple times.
Every time that an entry changes, it is added to the change table.
A network management application should follow the following algorithm
when polling this table:
1. Set lastChangeWrap = expressGSAddressChangeWraps.
2. Set lastChangeIndex = expressGSAddressChangeLast
3. Get the entire expressGSAddressEntryTable.
4. Submit a getNext for <lastChangeWrap>.<lastChangeIndex>,
updating lastChangeWrap and lastChangeIndex with the returned next
values. Update the address entry database with the changed values.
5. Repeat step 4 until no more entries are returned.
6. Wait polling timeout period.
7. Get wrap events counter and last index. If the wrap events counter is
equal to lastChangeWrap, then goto step 4. Else if the wrap events
counter is more then one greater then lastChangeWrap, goto step 1.
Else the wrap events counter is exactly one greater then
lastChangeWrap, and if the last index is greater then lastChangeIndex,
then goto step 1, else goto step 4.
The last step simply insures that we have not missed any of the change
entries. Essentially it says that if we have wrapped to beyond where we last
polled, then we must get the entire table to synch up again. Otherwise we
can just get the entries that have changed. ExpressGSL2AddressChangeEntry .1.3.6.1.4.1.343.6.13.5.1.4.4.4.1 |
expressGSL2AddressChangeWrapCountThe number of times that the expressGSAddressChangeLastIndex had
wrapped when this entry was added.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.4.4.1.1 |
expressGSL2AddressChangeIndexThe index that uniquely identifies this address change entry.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.4.4.1.2 |
expressGSL2AddressChangeIndexChangedThe address entry that changed. The value of this object corresponds to
the expressGSL2AddressIndex object.ro INTEGER .1.3.6.1.4.1.343.6.13.5.1.4.4.4.1.3 |
expressGSL2AddressChangeSummaryThe structure is interpreted in the following manner:ro OCTET STRING .1.3.6.1.4.1.343.6.13.5.1.4.4.4.1.4 |
expressGSSwitchPortMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.2 |
expressGSSwitchPortTable SEQUENCE OF ExpressGSSwitchPortEntry .1.3.6.1.4.1.343.6.13.5.2.1 |
expressGSSwitchPortEntry ExpressGSSwitchPortEntry .1.3.6.1.4.1.343.6.13.5.2.1.1 |
expressGSSwitchPortIndexA unique index that identifies this switch port. The value of
this index corresponds to the value of the expressGSResourceIndex for
switch ports.ro ResourceId .1.3.6.1.4.1.343.6.13.5.2.1.1.1 |
expressGSSwitchPortSTAPModeDisabling spanning tree on a switch port prevents the switch
port from participating in the spanning tree process. When
disabled(2), this port will neither generate BPDUs, nor process
received BPDUs. Also, the port will always start in the
forwarding state. A port configured in this mode will not be
able to detect network loops involving this port.
The factory default is to enable spanning tree on all ports.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.2 |
expressGSSwitchPortConvertToStaticWhen this object is set to convertToStatic(2), all addresses
learned on this port will be added to the non-volatile version
of the static address table.
Typically, this object will be used to perform a crude form of
address database update where the address activity associated
with this port is collected as static (i.e. permanent) addresses
while the value of this object is set to convertToStatic(2).
Following this usually short period of time (perhaps a week of
activity), the value of this object is restored back to its
default value of learnAsDynamic(1) and learning for this port is
disabled.
It is important that the user verify the address database to
verify that only the desired addresses were made permanent.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.3 |
expressGSSwitchPortLearningModeDisable learning on a bridge port to prevent new addresses from
being added to the address database. Used in combination with
static (permanent) address entries, disabling address learning
is an effective security feature to prevent new hosts from
appearing on the network, or to prevent hosts from moving to
different locations in the network. The default is enable.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.4 |
expressGSSwitchPortHuntGroupHunt groups provide the capability to logically bind multiple
switch ports into one switch port. This provides a way of
balancing the load of multiple links between like-configured
switches.
Care must be taken to configure the hunt groups properly to
prevent accidental network looping.
Use this object to bind this port to a specific hunt group.
When not configured to a specific hunt group, set the value of
this object to zero.rw INTEGER .1.3.6.1.4.1.343.6.13.5.2.1.1.5 |
expressGSSwitchPortPhysicalPortThe physical port resource bound to this switch port.ro ResourceId .1.3.6.1.4.1.343.6.13.5.2.1.1.6 |
expressGSSwitchPortKnownModeEnabling known mode for this switch port causes the port to
safely discard frames flooded because they are unknown unicast
frames. This mode greatly enhances the efficiency of the port's
output buffer since space is not wasted for frames not meant for
this port.
Enabling this feature disables learning for this port.
Addresses associated for this port should be entered statically.
The default is disable.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.7 |
expressGSSwitchPortMappingMethodThe frame mapping method of this switch port. When set to
port-based(1) (the factory default), all non-tagged frames are
classified to the VLAN associated with this switch port.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.8 |
expressGSSwitchPortTrunkingModeThe trunking mode of this port. All frames transmitted out
this switch port are translated to the appropriate trunking
format:
Clear: Ethernet or IEEE 802.3 frame format.
This is the default.
IEEE 802.1Q: The original frame with a new Ethernet Type
(Protocol = 0xXXXX) and the VLAN ID inserted
following the original Source Address.
Also, the CRC is recalculated.
Multi-level: The original frame is encapsulated in an
IEEE 802.3 legal frame proprietary to a
major networking equipment vendor.
3Com LinkSwitch: The original frame has the VLAN ID added to
the front of the frame (before the
Destination Address). Trunking format is
proprietary to 3Com Corporation.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.9 |
expressGSSwitchPortVlanBindingMethodThe VLAN binding method of a switch port specifies the way in
which the port can be a member of the egress lists of VLANs
other than the port default VLAN specified by
expressGSSwitchPortVlanID:
static: A Virtual Switch Port must be statically created for
each VLAN/port combination.
persistent: A Virtual Switch Port is automatically created for
each VLAN known to the switch (i.e., the port is
a member of the egress lists of all VLANs).
dynamic: A Virtual Switch Port is automatically created for
each VLAN when the associated VLAN ID is used as a
tag in an IEEE 802.1Q or Multi-level tagged frame
received on the port (i.e., the port is a member of
the egress lists of the VLANs from frames received
on the port).
The default is static.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.10 |
expressGSSwitchPortIgnoreTagEach switch port is capable of ignoring the VLAN Tag associated
with a frame in a trunking format. When ignored, the tag is
used as the default in the event that a VLAN classification
based on the switch's policy(s) cannot be made.
This feature is useful for connecting layer 2 VLANs and layer 3
VLANs. The default is useTag.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.11 |
expressGSSwitchPortVlanIDWhen this switch port is configured in port-based VLAN mode,
all non-tagged frames received on this port are bound to this
VLAN. Otherwise, non-tagged frames are classified to this VLAN
as the default if a VLAN binding cannot be otherwise determined.
The factory default is 1, which is the VLAN ID of the Default
VLAN.rw INTEGER .1.3.6.1.4.1.343.6.13.5.2.1.1.12 |
expressGSSwitchPort3ComMappingTableIndexThe 3Com VLAN mapping table associated with this switch port.
The default is 1, which indicates the default mapping table.rw INTEGER .1.3.6.1.4.1.343.6.13.5.2.1.1.13 |
expressGSSwitchPortAutoVlanCreationEnabling auto VLAN creation for this switch port causes the
port to dynamically create a VLAN whenever an IEEE 802.1Q or
Multi-level tagged frame is received on the port with a tag value
which does not correspond to a known VLAN. All switch ports with
a trunking mode of IEEE 802.1Q or Multi-level are bound to this
created VLAN. The default is disable.rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.14 |
expressGSSwitchPortMirrorModeWhen set to enable(1), this object indicates that the port is
defined as a mirror port through the expressGSPortMirroringTable. A
mirror port duplicates frames received at one or more source ports.ro Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.15 |
expressGSSwitchPortIfIndexEach switch port is associated with an interface. This object
provides a mechanism to map switch ports to bridge ports.ro INTEGER .1.3.6.1.4.1.343.6.13.5.2.1.1.16 |
expressGSSwitchPortFastStartWhen this object is set to enable(1), bridge ports on this switch port
transitions right from blocking to forwarding, skipping the listening
and learning states. The user should be warned that using the fast start
feature greatly increases the likelihood of unintended network loops that
would otherwise be prevented by participating in the normal spanning tree
algorithm.
The factory default value for this object is disable(2).rw Enumeration .1.3.6.1.4.1.343.6.13.5.2.1.1.17 |
expressGSHuntGroupMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.4 |
expressGSHuntGroupTable SEQUENCE OF ExpressGSHuntGroupEntry .1.3.6.1.4.1.343.6.13.5.4.1 |
expressGSHuntGroupEntry ExpressGSHuntGroupEntry .1.3.6.1.4.1.343.6.13.5.4.1.1 |
expressGSHuntGroupIndexAn index that uniquely identifies this hunt group. This index corresponds
to the value of expressGSResourceIndex for resources of the hunt group type.ro INTEGER .1.3.6.1.4.1.343.6.13.5.4.1.1.1 |
expressGSHuntGroupNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.343.6.13.5.4.1.1.2 |
expressGSHuntGroupBasePortThe switch port index that serves as the base port for this hunt group.
Each hunt group requires a base port. In lieu of a specific configuration,
the hunt group will inherit the first switch port bound to the hunt group as
its base port.
The base port serves as the management focus for the hunt group. That is,
a hunt group is managed as one switch port whose instance is provided by
the base switch port. All configuration (e.g. spanning tree information) and
statistics related to switch ports are meaningful only through the instance of
the base port.ro ResourceId .1.3.6.1.4.1.343.6.13.5.4.1.1.3 |
expressGSHuntGroupNumberOfPortsThe current number of ports that belong to this hunt group.ro INTEGER .1.3.6.1.4.1.343.6.13.5.4.1.1.4 |
expressGSHuntGroupLoadSharingrw Enumeration .1.3.6.1.4.1.343.6.13.5.4.1.1.5 |
expressGSHuntGroupStatusrw Enumeration .1.3.6.1.4.1.343.6.13.5.4.1.1.6 |
expressGSPortMirroringMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.5.5 |
expressGSPortMirroringTableA table of port mirroring entries used to mirror traffic from
a source port to a mirror port. SEQUENCE OF ExpressGSPortMirroringEntry .1.3.6.1.4.1.343.6.13.5.5.1 |
expressGSPortMirroringEntryObjects related to the PortMirroring functionality. ExpressGSPortMirroringEntry .1.3.6.1.4.1.343.6.13.5.5.1.1 |
expressGSPortMirroringIndexThe unique index that identifies this entry. This index consists
of a switch fabric port and the index of a Packet Lookup Engine
servicing this fabric port.ro ResourceId .1.3.6.1.4.1.343.6.13.5.5.1.1.1 |
expressGSPortMirroringSourceSubPortThe frame sampler source switch subport. The source port is the
port from which received traffic will be mirrored. This object
identifies the switch subport only, the switch fabric port is
identified in expressGSPortMirroringIndex. If set to 0, all subports
associated with the expressGSPortMirroringIndex will be source ports. The
default value is 0.rw INTEGER .1.3.6.1.4.1.343.6.13.5.5.1.1.2 |
expressGSPortMirroringSamplerTypeThe type for this frame sampler. When set to enable(1), every
frame received on the source port(s) will be mirrored at the mirror
port. When set to disable(2), no frames received on the source
port(s) will be mirrored at the mirror port. When set to
periodic(3), frames will be mirrored at the rate defined in
expressGSPortMirroringRate. The default value is disable(2).rw Enumeration .1.3.6.1.4.1.343.6.13.5.5.1.1.3 |
expressGSPortMirroringRateUsed in conjunction with expressGSPortMirroringSamplerType to implement
periodic sampling functionality. If expressGSPortMirroringSamplerType is
set to periodic(3), this object defines the number of packets/second
that will be mirrored. If expressGSPortMirroringSamplerType is not
periodic(3), this object will set to 0.rw INTEGER .1.3.6.1.4.1.343.6.13.5.5.1.1.4 |
expressGSPortMirroringMirrorPortThe Switch Port on which frames received at source ports(s) will be
duplicated. If no mirror port has been defined this object will
return NULL.rw ResourceId .1.3.6.1.4.1.343.6.13.5.5.1.1.5 |
expressGSVlanMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.7 |
expressGSVlans OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.7.1 |
expressGSVlanTable SEQUENCE OF ExpressGSVlanEntry .1.3.6.1.4.1.343.6.13.7.1.1 |
expressGSVlanEntry ExpressGSVlanEntry .1.3.6.1.4.1.343.6.13.7.1.1.1 |
expressGSVlanIDAn identifier that is unique within the administrative domain.
This ID is assigned by the management application and is
meaningful within that context.
This ID is used to identify VLANs when tagged using either the
IEEE 802.1 frame format or the Multi-level frame format.ro INTEGER .1.3.6.1.4.1.343.6.13.7.1.1.1.1 |
expressGSVlanNameA user-assignable name for this Vlan.rw DisplayString .1.3.6.1.4.1.343.6.13.7.1.1.1.2 |
expressGSVlanIfIndexEach virtual LAN has a virtual interface associated with it.
This enables RMON monitoring to occur per-VLAN. It also
provides a handy mechanism to map virtual LANs to bridge ports
by mapping them with the ifStack table from the Interface MIB.ro INTEGER .1.3.6.1.4.1.343.6.13.7.1.1.1.3 |
expressGSVlanAFTIndexThe address table used for this VLAN for explicitly tagged
frames (frames received in a trunking frame format or from a
port in port-based VLAN mode.) Normally, each VLAN maps to a
unique address table. This is useful for environments with
duplicate host addresses appear on different VLANs on different
ports.
For those environments where duplicate hosts on different VLANs
don't exist, or exist but are on the same port, and where the
address table size and/or aging is a concern, then multiple
VLANs may be mapped to the same address table.rw INTEGER .1.3.6.1.4.1.343.6.13.7.1.1.1.4 |
expressGSVlanBridgeIndexThe bridge resource which is bound to this Vlan.rw ResourceId .1.3.6.1.4.1.343.6.13.7.1.1.1.5 |
expressGSVlanStatusThe status of an entry to be created or deleted.
When adding an entry all fields will be set, and then the status
is set to createRequest(1) (indicating that the entry is to be
created). When deleting an entry the status is set to
destroyRequest(3) (indicating that the entry is to be destroyed).
During creation the status will be underCreation(2). If the
creation is successful, then the status will be set to
active(5). Otherwise if the creation was not successful then
one of the following error codes will be set and the entry will
not be created:
otherError(6) - An error other than the others defined.
entryExistsError(7) - An entry already exists.
invalidVlanID(8) - the VLAN ID is invalid.
invalidVlanName(9) - the VLAN name is invalid.
invalidVlanAFTIndex(10) - the VLAN AFT index is invalid.
invalidVlanBridgeIndex(11) - the VLAN bridge index is invalid.
invalidVlanInitialHashTableSize(12) - the VLAN initial hash
table size is invalid.
invalidVlanAutoIncrementHTSize(13) - the VLAN auto increment
hash table size is
invalid.rw Enumeration .1.3.6.1.4.1.343.6.13.7.1.1.1.6 |
expressGSVlanInitialHashTableSizeThe initial hash table size used for MAC addresses on this
VLAN. This attribute may only be set when expressGSVlanStatus is
set to createRequest(1). It must be a power of 2 between 16
and 8192, inclusive.rw INTEGER .1.3.6.1.4.1.343.6.13.7.1.1.1.7 |
expressGSVlanAutoIncrementHTSizeThis attribute specifies whether or not the hash table size
used for MAC addresses on this VLAN is automatically increased
as necessary to hold more MAC addresses. This attribute may only
be set when expressGSVlanStatus is set to createRequest(1).rw Enumeration .1.3.6.1.4.1.343.6.13.7.1.1.1.8 |
expressGSVlanMappings OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.7.3 |
expressGS3ComMapping OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.7.3.1 |
expressGS3ComMappingTable SEQUENCE OF ExpressGS3ComMappingEntry .1.3.6.1.4.1.343.6.13.7.3.1.1 |
expressGS3ComMappingEntry ExpressGS3ComMappingEntry .1.3.6.1.4.1.343.6.13.7.3.1.1.1 |
expressGS3ComMappingTableIndexro INTEGER .1.3.6.1.4.1.343.6.13.7.3.1.1.1.1 |
expressGS3ComMappingTableNameA user-readable name associated with this table.rw DisplayString .1.3.6.1.4.1.343.6.13.7.3.1.1.1.2 |
expressGS3ComMappingTableStatusThe status of an entry to be created. When adding an entry all
fields will be set, and then the status is set to
createRequest(1), indicating that the entry is to be created.
If the creation is successful, then the status will be set to
active(3). Otherwise if the creation was not successful then
one of the following error codes will be set and the entry will
not be created:
entryExistsError(4) - An entry already exists.
otherError(5) - An error other than the others defined.rw Enumeration .1.3.6.1.4.1.343.6.13.7.3.1.1.1.3 |
expressGSVlan3ComMapping OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.7.3.2 |
expressGSVlan3ComMappingTable SEQUENCE OF ExpressGSVlan3ComMappingEntry .1.3.6.1.4.1.343.6.13.7.3.2.1 |
expressGSVlan3ComMappingEntry ExpressGSVlan3ComMappingEntry .1.3.6.1.4.1.343.6.13.7.3.2.1.1 |
expressGSVlan3ComMappingIndexThe external tag of this 3Com VLAN.ro INTEGER .1.3.6.1.4.1.343.6.13.7.3.2.1.1.1 |
expressGSVlan3ComMappingVlanIDThe VLAN ID of the VLAN that this 3Com tag is associated with.rw INTEGER .1.3.6.1.4.1.343.6.13.7.3.2.1.1.2 |
expressGSVlan3ComMappingStatusThe status of an entry to be created. When adding an entry all
fields will be set, and then the status is set to
createRequest(1), indicating that the entry is to be created.
If the creation is successful, then the status will be set to
active(3). Otherwise if the creation was not successful then
one of the following error codes will be set and the entry will
not be created:
otherError(4) - An error other than the others defined.rw Enumeration .1.3.6.1.4.1.343.6.13.7.3.2.1.1.3 |
expressGSVirtualPorts OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.7.4 |
expressGSVirtualSwitchPortTable SEQUENCE OF ExpressGSVirtualSwitchPortEntry .1.3.6.1.4.1.343.6.13.7.4.1 |
expressGSVirtualSwitchPortEntryAn instance of a virtual switch port indicates that this
switch port is a member of this VLAN. ExpressGSVirtualSwitchPortEntry .1.3.6.1.4.1.343.6.13.7.4.1.1 |
expressGSVirtualSwitchPortIndexThe Resource ID of the virtual switch port bound to the VLAN.ro ResourceId .1.3.6.1.4.1.343.6.13.7.4.1.1.1 |
expressGSVirtualSwitchPortFormatTypically, a VLAN capable switch port has one of three modes:
access, trunk, or hybrid. In access mode, the port sends
frames in clear format (untagged). In trunk mode, all outbound
frames are translated into the switch port's configured
trunking format.
In hybrid mode, it is possible for a port to send trunked
frames for some VLANs and clear frames for others. In this
case, the switch port is configured to trunk, and the virtual
switch port(s) for those VLANs that require clear formatted
frames are configured to be override the switch port setting.
This is done by setting this object to clear(1).
By default, the value of this object is trunkingFormat(2)
which means to use the trunking format configured for this
switch port. (which may be clear).rw Enumeration .1.3.6.1.4.1.343.6.13.7.4.1.1.2 |
expressGSVirtualSwitchPortBridgePortThe bridge port resource bound to this virtual port.rw ResourceId .1.3.6.1.4.1.343.6.13.7.4.1.1.3 |
expressGSVirtualSwitchPortBindingTypeThe method by which this switch port was bound to the VLAN.
If the value is static(1), the binding was manually created
by the administrator. If the value is persistent(2), the
binding was created by the switch because the VLAN is the
port-based VLAN for the switch port, or the switch port
VLAN Binding Method is persistent. These bindings may not
be removed. If the value is dynamic(3), the binding was
created by the switch as a result of receiving a tagged
frame on the switch port with a VLAN ID corresponding to
the VLAN.ro Enumeration .1.3.6.1.4.1.343.6.13.7.4.1.1.4 |
expressGSVirtualSwitchPortStatusThe status of an entry to be created or deleted.
When adding an entry all fields will be set, and then the status
is set to createRequest(1) (indicating that the entry is to be
created). When deleting an entry the status is set to
destroyRequest(2) (indicating that the entry is to be destroyed).
If the creation is successful, then the status will be set to
active(3). Otherwise if the creation was not successful then
one of the following error codes will be set and the entry will
not be created:
otherError(4) - An error other than the others defined.
entryExistsError(5) - On creation, an entry already exists.
On deletion, the entry may not be
removed.
entryNoExistError(6) - The VLAN specified by ID
does not exist.rw Enumeration .1.3.6.1.4.1.343.6.13.7.4.1.1.5 |
expressGSEvents OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.10 |
expressGSEventMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.10.1 |
expressGSEventTableTable of events currently supported. SEQUENCE OF ExpressGSEventEntry .1.3.6.1.4.1.343.6.13.10.1.1 |
expressGSEventEntryAttributes associated with the event. ExpressGSEventEntry .1.3.6.1.4.1.343.6.13.10.1.1.1 |
expressGSEventIndexro INTEGER .1.3.6.1.4.1.343.6.13.10.1.1.1.1 |
expressGSEventModeDisabling an event prevents this event from taking any actions when
triggered.
When set to enable to the console, the event will print the event information
to the console serial port. The user can select whether to view log
messages, trap messages or any event at the console.rw Enumeration .1.3.6.1.4.1.343.6.13.10.1.1.1.2 |
expressGSEventLogActionWhen enabled, this action will cause an event log entry to be created.rw Enumeration .1.3.6.1.4.1.343.6.13.10.1.1.1.3 |
expressGSEventTrapActionWhen enabled, this event will cause an SNMP trap to be generated.rw Enumeration .1.3.6.1.4.1.343.6.13.10.1.1.1.4 |
expressGSEventConsoleActionWhen enabled, this event will cause a message to printed to the console serial port.rw Enumeration .1.3.6.1.4.1.343.6.13.10.1.1.1.5 |
expressGSEventLogMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.10.2 |
expressGSLogTableMaxSizeThe maximum number of entries in the log table.
Changing this value causes the existing log to be
truncated and rebuilt.rw INTEGER .1.3.6.1.4.1.343.6.13.10.2.1 |
expressGSLogLastEntryThe log index of the last entry entered in the log.ro INTEGER .1.3.6.1.4.1.343.6.13.10.2.2 |
expressGSLogWrapsThe number of times that the last entry has wrapped from 65K back to 1.ro Counter .1.3.6.1.4.1.343.6.13.10.2.3 |
expressGSEventLog OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.10.3 |
expressGSEventLogTableThe log table for the events in the event table that are enabled for the
Log Action. SEQUENCE OF ExpressGSEventLogEntry .1.3.6.1.4.1.343.6.13.10.3.1 |
expressGSEventLogEntryAn entry in the log indicates information associated with a particular
event. ExpressGSEventLogEntry .1.3.6.1.4.1.343.6.13.10.3.1.1 |
expressGSEventLogEventIndexThe index that uniquely identifies the event that caused this log entry.ro INTEGER .1.3.6.1.4.1.343.6.13.10.3.1.1.1 |
expressGSEventLogIndexAn index that uniquely identifies this log entry.ro INTEGER .1.3.6.1.4.1.343.6.13.10.3.1.1.2 |
expressGSEventLogTimeThe value of sysUpTime when this event was triggered.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.343.6.13.10.3.1.1.3 |
expressGSEventLogDescrThe event log description.ro DisplayString .1.3.6.1.4.1.343.6.13.10.3.1.1.4 |
expressGSEventLogTypeThe type of event that caused this log entry.ro EventCategory .1.3.6.1.4.1.343.6.13.10.3.1.1.5 |
expressGSEventLogSeverityThe severity associated with this event. It is recommended that the
severity be interpreted in the following manner:
0-19: Normal
20-39: Informational
40-59: Warning
60-79: Alarm
80-99: Severe Error
100: Failure.ro INTEGER .1.3.6.1.4.1.343.6.13.10.3.1.1.6 |
expressGSEventLogDTMThe date and time when this log entry was made. The format is yy-Mon-
dd hh:mm:ss, time is in 24 hour time.ro DisplayString .1.3.6.1.4.1.343.6.13.10.3.1.1.7 |
expressGSEventLogResTypeThe type of object (if provided) that triggered this event. If not provided,
the value is equal to 'Invalid Resource'.ro ResourceType .1.3.6.1.4.1.343.6.13.10.3.1.1.8 |
expressGSEventLogResIDThe instance of this resource (if provided - see expressGSEventLogResType)
that triggered this event.ro ResourceId .1.3.6.1.4.1.343.6.13.10.3.1.1.9 |
expressGSEventLogResLeafA number corresponding to the attribute associated with this resource and
this event entry. It corresponds exactly to the leaf MIB number of the MIB
that manages this resource. For example, if a port's mode changed, the
configuration event log entry would indicate the value of 5 which is the
leaf index of the expressGSPortMode within the expressGSPortTable MIB table.ro INTEGER .1.3.6.1.4.1.343.6.13.10.3.1.1.10 |
expressGSEventLogValueTypeThe data type associated with the log event value. This object indicates
how to interpret the data stored in the event log value:
- none(1) indicates no value returned.
- integer32(2) - a 4 byte unsigned integer.
- integer64(3) - an 8 byte unsigned integer.
- displayString(4) - a null terminated (or up to 8 characters) string.
- ipv4NetworkAddress(5) - a 4 byte IP version 4 network address.
- ieee802MACAddress(6) - a 6 byte MAC Address.
- timeticks(7) - sysUpTime type value (4 bytes)ro EventValueType .1.3.6.1.4.1.343.6.13.10.3.1.1.11 |
expressGSEventLogValueThe value associated with the event encoded in an octet string. Refer to
expressGSEventLogValueType for how to interpret this value.
The value encoded in this string is in Big Endian order.ro OCTET STRING .1.3.6.1.4.1.343.6.13.10.3.1.1.12 |
expressGSEventLogEpochTimeThe number of time ticks since the epoch when this
event was logged. The interpretation of this value is
as follows:
struct DateTimeOvly {
UNS32 year:6;
UNS32 month:4;
UNS32 day:5;
UNS32 hour:5;
UNS32 minute:6;
UNS32 second:6;
};
The epoch is January 1, 1997, at 00:00:00. A value of
0 refers to this date and time.ro INTEGER .1.3.6.1.4.1.343.6.13.10.3.1.1.13 |
expressGSEventLogIDA unique index that identifies the occurence of this
event. This ID can be correlated between traps, logs
and the like.ro INTEGER .1.3.6.1.4.1.343.6.13.10.3.1.1.14 |
expressGSShutdownLogMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.10.4 |
expressGSShutdownLogTableMaxSizeThe maximum number of entries in the non-volatile log table. Changing
the value of this object changes the maximum number of entries to be
stored in Shutdown.rw INTEGER .1.3.6.1.4.1.343.6.13.10.4.1 |
expressGSShutdownLogLastEntryThe ID of the last entry made to the shutdown log.ro INTEGER .1.3.6.1.4.1.343.6.13.10.4.2 |
expressGSShutdownLogAcknowledgedThis object is to set to acknowledged(2) the first time the Shutdown Log
Table is accessed indicating that the Shutdown log has been read (at least
once) since the system restarted.ro Enumeration .1.3.6.1.4.1.343.6.13.10.4.3 |
expressGSEventShutdownLog OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.10.5 |
expressGSEventShutdownLogTableA table of the last events logged before the system restarted. SEQUENCE OF ExpressGSEventShutdownLogEntry .1.3.6.1.4.1.343.6.13.10.5.1 |
expressGSEventShutdownLogEntryA log entry stored in non-volatile memory. ExpressGSEventShutdownLogEntry .1.3.6.1.4.1.343.6.13.10.5.1.1 |
expressGSEventShutdownLogEventIndexThe index that uniquely identifies the event that caused this ShutdownLog
entry.ro INTEGER .1.3.6.1.4.1.343.6.13.10.5.1.1.1 |
expressGSEventShutdownLogIndexAn index that uniquely identifies this ShutdownLog entry.ro INTEGER .1.3.6.1.4.1.343.6.13.10.5.1.1.2 |
expressGSEventShutdownLogTimeThe value of sysUpTime when this event was triggered. Note,
the value corresponds to the sysUpTime when the system was last
running (i.e. before it was shutdown.)ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.343.6.13.10.5.1.1.3 |
expressGSEventShutdownLogDescrThe event ShutdownLog description.ro DisplayString .1.3.6.1.4.1.343.6.13.10.5.1.1.4 |
expressGSEventShutdownLogTypeThe type of event that caused this ShutdownLog entry.ro EventCategory .1.3.6.1.4.1.343.6.13.10.5.1.1.5 |
expressGSEventShutdownLogSeverityThe severity associated with this event. It is recommended that the
severity be interpreted in the following manner:
0-19: Normal
20-39: Informational
40-59: Warning
60-79: Alarm
80-99: Severe Error
100: Failure.ro INTEGER .1.3.6.1.4.1.343.6.13.10.5.1.1.6 |
expressGSEventShutdownLogDTMThe date and time when this ShutdownLog entry was made. The format
is yy-Mon-dd hh:mm:ss, time is in 24 hour time.ro DisplayString .1.3.6.1.4.1.343.6.13.10.5.1.1.7 |
expressGSEventShutdownLogResTypeThe type of object (if provided) that triggered this event. If not provided,
the value is invalid.ro ResourceType .1.3.6.1.4.1.343.6.13.10.5.1.1.8 |
expressGSEventShutdownLogResIDThe instance of this resource (if provided) that triggered this event.ro ResourceId .1.3.6.1.4.1.343.6.13.10.5.1.1.9 |
expressGSEventShutdownLogResLeafTo be provided.ro INTEGER .1.3.6.1.4.1.343.6.13.10.5.1.1.10 |
expressGSEventShutdownLogValueTypeThe data type associated with the ShutdownLog event value. This object
indicates how to interpret the data stored in the event ShutdownLog
value.ro EventValueType .1.3.6.1.4.1.343.6.13.10.5.1.1.11 |
expressGSEventShutdownLogValueThe value associated with the event encoded in an octet string.ro OCTET STRING .1.3.6.1.4.1.343.6.13.10.5.1.1.12 |
expressGSEventShutdownLogEpochTimeThe number of time ticks since the epoch when this
event was logged. The interpretation of this value is
as follows:
struct DateTimeOvly {
UNS32 year:6;
UNS32 month:4;
UNS32 day:5;
UNS32 hour:5;
UNS32 minute:6;
UNS32 second:6;
};
The epoch is January 1, 1997, at 00:00:00. A value of
0 refers to this date and time.ro INTEGER .1.3.6.1.4.1.343.6.13.10.5.1.1.13 |
expressGSEventShutdownLogIDA unique index that identifies the occurence of this
event. This ID can be correlated between traps, logs
and the like.ro INTEGER .1.3.6.1.4.1.343.6.13.10.5.1.1.14 |
expressGSEventTrapMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.10.6 |
expressGSEventTrapEventIndexThe index that uniquely identifies the event that caused this trap.ro INTEGER .1.3.6.1.4.1.343.6.13.10.6.1 |
expressGSEventTrapTimeThe value of sysUpTime when this event was triggered.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.343.6.13.10.6.2 |
expressGSEventTrapDescrThe event log description.ro DisplayString .1.3.6.1.4.1.343.6.13.10.6.3 |
expressGSEventTrapTypeThe type of event that caused this trap.ro EventCategory .1.3.6.1.4.1.343.6.13.10.6.4 |
expressGSEventTrapSeverityThe severity associated with this event. It is recommended that the
severity be interpreted in the following manner:
0-19: Normal
20-39: Informational
40-59: Warning
60-79: Alarm
80-99: Severe Error
100: Failure.ro INTEGER .1.3.6.1.4.1.343.6.13.10.6.5 |
expressGSEventTrapDTMThe date and time when this trap was sent. The format is yy-Mon-
dd hh:mm:ss, time is in 24 hour time.ro DisplayString .1.3.6.1.4.1.343.6.13.10.6.6 |
expressGSEventTrapResTypeThe type of object (if provided) that triggered this event. If not provided,
the value is equal to 'Invalid Resource'.ro ResourceType .1.3.6.1.4.1.343.6.13.10.6.7 |
expressGSEventTrapResIDThe instance of this resource (if provided - see expressGSEventTrapResType)
that triggered this event.ro ResourceId .1.3.6.1.4.1.343.6.13.10.6.8 |
expressGSEventTrapResLeafA number corresponding to the attribute associated with this resource and
this event entry. It corresponds exactly to the leaf MIB number of the MIB
that manages this resource. For example, if a port's mode changed, the
configuration event log entry would indicate the value of 5 which is the
leaf index of the expressGSPortMode within the expressGSPortTable MIB table.ro INTEGER .1.3.6.1.4.1.343.6.13.10.6.9 |
expressGSEventTrapValueTypeThe data type associated with the trap event value. This object indicates
how to interpret the data stored in the event trap value:
- none(1) indicates no value returned.
- integer32(2) - a 4 byte unsigned integer.
- integer64(3) - an 8 byte unsigned integer.
- displayString(4) - a null terminated (or up to 8 characters) string.
- ipv4NetworkAddress(5) - a 4 byte IP version 4 network address.
- ieee802MACAddress(6) - a 6 byte MAC Address.
- timeticks(7) - sysUpTime type value (4 bytes)ro EventValueType .1.3.6.1.4.1.343.6.13.10.6.10 |
expressGSEventTrapValueThe value associated with the event encoded in an octet string. Refer to
expressGSEventTrapValueType for how to interpret this value.
The value encoded in this string is in Big Endian order.ro OCTET STRING .1.3.6.1.4.1.343.6.13.10.6.11 |
expressGSEventTrapEpochTimeThe number of time ticks since the epoch when this
event was logged. The interpretation of this value is
as follows:
struct DateTimeOvly {
UNS32 year:6;
UNS32 month:4;
UNS32 day:5;
UNS32 hour:5;
UNS32 minute:6;
UNS32 second:6;
};
The epoch is January 1, 1997, at 00:00:00. A value of
0 refers to this date and time.ro INTEGER .1.3.6.1.4.1.343.6.13.10.6.12 |
expressGSEventTrapIDA unique index that identifies the occurence of this
event. This ID can be correlated between traps, logs
and the like.ro INTEGER .1.3.6.1.4.1.343.6.13.10.6.13 |
expressGSAlarmMgt OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.11 |
expressGSAlarmGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.11.1 |
expressGSAlarmGeneralActiveEntriesThe total number of alarm entries in the triggered state currently in the
alarm table.ro Gauge .1.3.6.1.4.1.343.6.13.11.1.1 |
expressGSAlarmGeneralTimeStampThe value of sysUpTime when any alarm state last changed (either
triggering a new alarm or re-arming an old one).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.343.6.13.11.1.2 |
expressGSAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.11.2 |
expressGSActiveAlarmTableA table of all alarms in the triggered state. SEQUENCE OF ExpressGSActiveAlarmEntry .1.3.6.1.4.1.343.6.13.11.2.2 |
expressGSActiveAlarmEntryAn alarm in the triggered state. ExpressGSActiveAlarmEntry .1.3.6.1.4.1.343.6.13.11.2.2.1 |
expressGSActiveAlarmIndexThe unique index that identifies this alarm.ro INTEGER .1.3.6.1.4.1.343.6.13.11.2.2.1.1 |
expressGSActiveAlarmNameThe name of this alarm.ro DisplayString .1.3.6.1.4.1.343.6.13.11.2.2.1.2 |
expressGSActiveAlarmValueHighThe high order 32 bits of the value that triggered this alarm.ro INTEGER .1.3.6.1.4.1.343.6.13.11.2.2.1.3 |
expressGSActiveAlarmValueLowThe low order 32 bits of the value that triggered this alarm.ro INTEGER .1.3.6.1.4.1.343.6.13.11.2.2.1.4 |
expressGSActiveAlarmVariableThe OID of the alarm variable if this is a user-created alarm (null
otherwise).ro OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.11.2.2.1.5 |
expressGSActiveAlarmResTypeThe resource type of this alarm if this is an internally created alarm.ro ResourceType .1.3.6.1.4.1.343.6.13.11.2.2.1.6 |
expressGSActiveAlarmResIDThe resource identifier associated with this alarm if this is an internally created alarm.ro ResourceId .1.3.6.1.4.1.343.6.13.11.2.2.1.7 |
expressGSActiveAlarmLeafThe leaf index of the MIB table used to manage this resource that is associated with this
alarm, if this is an internally created alarm. For example, if this alarm was created to
monitor a port's status, then the value of this object will be 6, corresponding to the leaf
index of the expressGSPortStatus object.ro INTEGER .1.3.6.1.4.1.343.6.13.11.2.2.1.8 |
expressGSActiveAlarmOwnerThis is the owner of the alarm.ro DisplayString .1.3.6.1.4.1.343.6.13.11.2.2.1.9 |
expressGSSnmpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.13.13 |
expressGSSystemTrapA expressGSSystemTrap is sent by the agent when a system
event is triggered. These events are usually triggered
when the software encounters an unexpected situation,
e.g. a hardware failure or a software bug. TRAP-TYPE .1.3.6.1.4.1.343.6.13.13.0.2 |
expressGSConfigurationTrapA expressGSConfigurationTrap is sent by the agent when the
configuration event is triggered. These events are
triggered when a configuration change is made. TRAP-TYPE .1.3.6.1.4.1.343.6.13.13.0.3 |
expressGSTemperatureTrapA expressGSTemperatureTrap is sent by the agent when the
temperature event is triggered. This event is
triggered when a temperature probe detects the
temperature crossing a threshold. TRAP-TYPE .1.3.6.1.4.1.343.6.13.13.0.4 |
expressGSResourceTrapA expressGSResourceTrap is sent by the agent when the
resource event is triggered. The resource event is
triggered when a resource is added or removed from the
system. TRAP-TYPE .1.3.6.1.4.1.343.6.13.13.0.5 |
expressGSFanTrapA expressGSFanTrap is sent by the agent when the
fan status event is triggered. The fan status event
is triggered when a fan has a change in its status. TRAP-TYPE .1.3.6.1.4.1.343.6.13.13.0.6 |
expressGSPowerTrapA expressGSPowerTrap is sent by the agent when the power
event is triggered. These events are triggered when a
power supply changes status. TRAP-TYPE .1.3.6.1.4.1.343.6.13.13.0.9 |