INTEL-ES400-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
206
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
206 total| Object Name |
|---|
intel OBJECT IDENTIFIER .1.3.6.1.4.1.343 |
RFC1213-MIB Unknown .1.3.6.1.4.1.343 |
mib2ext OBJECT IDENTIFIER .1.3.6.1.4.1.343.6 |
es400 OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17 |
portPartitionThe trap is sent whenever the port state enter the
Partion mode when more than 61 collisions occur while
trasmitting. TRAP-TYPE .1.3.6.1.4.1.343.6.17.0.1 |
linkChangeEventThe trap is sent whenever the link state of a port changes
from link up to link down or from link down to link up TRAP-TYPE .1.3.6.1.4.1.343.6.17.0.2 |
broadcastRisingStormThe trap indicates that broadcast higher rising threshold
. This trap including the port ID TRAP-TYPE .1.3.6.1.4.1.343.6.17.0.3 |
broadcastFallingStormThe trap indicates that broadcast higher falling threshold
. This trap including the port ID TRAP-TYPE .1.3.6.1.4.1.343.6.17.0.4 |
es400Agent OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.1 |
es400AgentInfo OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.1.1 |
es400AgentRuntimeSwVersionThis is a textual description of the runtime software version and
revision. If the version number is one and revision number is zero
es400AgentRuntimeSwVersion would be 'Ver. 1.0'ro DisplayString .1.3.6.1.4.1.343.6.17.1.1.1 |
es400AgentPromFwVersionThis is a textual description of the agent PROM firmware version
and revision. If the version number is one and revision number is
zero es400AgentPromFwVersion would be 'Ver. 1.0'ro DisplayString .1.3.6.1.4.1.343.6.17.1.1.2 |
es400AgentHwRevisionThis is a integer number of the hardware revision.ro INTEGER .1.3.6.1.4.1.343.6.17.1.1.3 |
es400AgentMgmtProtocolCapabilityThe network management protocol(s) supported by this agent.ro Enumeration .1.3.6.1.4.1.343.6.17.1.1.4 |
es400AgentMibSupportTableA list of MIB capability entries supported by this agent. SEQUENCE OF Es400AgentMibSupportEntry .1.3.6.1.4.1.343.6.17.1.1.5 |
es400AgentMibSupportEntryA MIB capability entry contains objects describing a particular MIB
supported by this agent. Es400AgentMibSupportEntry .1.3.6.1.4.1.343.6.17.1.1.5.1 |
es400AgentMibSupportIndexA list of es400AgentMibSupportDescr entries.ro INTEGER .1.3.6.1.4.1.343.6.17.1.1.5.1.1 |
es400AgentMibSupportDescrThe name of the MIB supported by the agent.ro DisplayString .1.3.6.1.4.1.343.6.17.1.1.5.1.2 |
es400AgentMibSupportVersionThe version of the MIB specified in this entry.ro INTEGER .1.3.6.1.4.1.343.6.17.1.1.5.1.3 |
es400AgentMibSupportTypeThe type of the MIB specified in this entry.ro Enumeration .1.3.6.1.4.1.343.6.17.1.1.5.1.4 |
es400AgentConfig OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.1.2 |
es400AgentSwUpdateModeThe download media used by the system to download the runtime
software.rw Enumeration .1.3.6.1.4.1.343.6.17.1.2.1 |
es400AgentSwUpdateCtrlCurrent status of configuration software download control. The setting is
effective the next time you reset or power on the hub.rw Enumeration .1.3.6.1.4.1.343.6.17.1.2.2 |
es400AgentBootFileThe name of the configuration file to be downloaded from the TFTP server
when software update is enabled.rw DisplayString .1.3.6.1.4.1.343.6.17.1.2.3 |
es400AgentFirmwareUpdateCtrlCurrent status of firmware software download control. The setting is
effective the next time you reset or power on the hub.rw Enumeration .1.3.6.1.4.1.343.6.17.1.2.4 |
es400AgentFirmwareFileThe name of the firmware file to be downloaded from the TFTP server
when software update is enabled.rw DisplayString .1.3.6.1.4.1.343.6.17.1.2.5 |
es400AgentSystemResetThis object indicates the agent system reset state. Setting this
object to no-reset(4) has no effect. Setting this object to
cold-start(2) or warm-start(3) will reset the agent. The agent
always returns no-reset(4) when this object is read.rw Enumeration .1.3.6.1.4.1.343.6.17.1.2.6 |
es400AgentRs232PortConfigThis object indicates the RS-232C mode while device restart.rw Enumeration .1.3.6.1.4.1.343.6.17.1.2.7 |
es400AgentOutOfBandBaudRateConfigThis object indicates the out_of_band baud rate while device
restart.rw Enumeration .1.3.6.1.4.1.343.6.17.1.2.8 |
es400AgentIpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.1.3 |
es400AgentIpNumOfIfThe total number of IP interfaces supported by this agent.ro INTEGER .1.3.6.1.4.1.343.6.17.1.3.1 |
es400AgentIpIfTableA list of IP interface entries supported by the agent. SEQUENCE OF Es400AgentIpIfEntry .1.3.6.1.4.1.343.6.17.1.3.2 |
es400AgentIpIfEntryAn es400AgentIPIfEntry contains information about a particular IP
interface. Es400AgentIpIfEntry .1.3.6.1.4.1.343.6.17.1.3.2.1 |
es400AgentIpIfIndexThis object uniquely identifies the IP interface number in the
es400AgentIpIfTable. This value should never greater than es400AgentIpNumOfIfro INTEGER .1.3.6.1.4.1.343.6.17.1.3.2.1.1 |
es400AgentIpIfAddressThe IP address of the interface.rw IpAddress .1.3.6.1.4.1.343.6.17.1.3.2.1.2 |
es400AgentIpIfNetMaskThe IP net mask for this interface.rw IpAddress .1.3.6.1.4.1.343.6.17.1.3.2.1.3 |
es400AgentIpIfDefaultRouterThe default gateway for this IP interface.rw IpAddress .1.3.6.1.4.1.343.6.17.1.3.2.1.4 |
es400AgentIpIfMacAddrThe MAC address of this IP interface. For interfaces which do not
have such an address. (e.g., a serial line), this object should
contain an octet string of zero length.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.343.6.17.1.3.2.1.5 |
es400AgentIpIfTypeThe physical layer interface of the IP interface.ro Enumeration .1.3.6.1.4.1.343.6.17.1.3.2.1.6 |
es400AgentIpBootServerAddrThe IP Address of Boot Server.rw IpAddress .1.3.6.1.4.1.343.6.17.1.3.3 |
es400AgentIpGetIpFromBootpServerThis object indicates whether the agent get its system IP address
from Bootp server at start up.rw Enumeration .1.3.6.1.4.1.343.6.17.1.3.4 |
es400AgentIpUnauthAddrThe IP address of an unauthorized SNMP packet.ro IpAddress .1.3.6.1.4.1.343.6.17.1.3.5 |
es400AgentIpUnauthCommThe community string of an unauthorized SNMP packet.ro DisplayString .1.3.6.1.4.1.343.6.17.1.3.6 |
es400AgentIpLastBootServerAddrThe last IP address used as Boot server IP address.ro IpAddress .1.3.6.1.4.1.343.6.17.1.3.7 |
es400AgentIpLastIpAddrThe last IP address used as the agent system IP address.ro IpAddress .1.3.6.1.4.1.343.6.17.1.3.8 |
es400AgentTrapAddressTableA list of trap manager entries to which to send SNMP traps . SEQUENCE OF Es400AgentTrapAddressEntry .1.3.6.1.4.1.343.6.17.1.4 |
es400AgentTrapAddressEntryThis entry contains the particular trap manager settings. Es400AgentTrapAddressEntry .1.3.6.1.4.1.343.6.17.1.4.1 |
es400AgentTrapIndexThe table index to receive SNMP traps from this device.ro INTEGER .1.3.6.1.4.1.343.6.17.1.4.1.1 |
es400AgentTrapAddressIpThe IP address to receive SNMP traps from this device.rw IpAddress .1.3.6.1.4.1.343.6.17.1.4.1.2 |
es400AgentTrapAddressCommThe community string of the SNMP trap packet sent to the trap
manager.rw DisplayString .1.3.6.1.4.1.343.6.17.1.4.1.3 |
es400AgentTrapAddressStatusThis object indicates whether or not the trap should be send to
this trap manager.rw Enumeration .1.3.6.1.4.1.343.6.17.1.4.1.4 |
es400Chassis OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.2 |
es400ChassisInfo OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.2.1 |
es400ChassisInfoSystemUpTimeThe value of sysUpTime at the time the switch entered its
current operational state. If the current state was entered
prior to the last re-initialization, then this object contains
a zero value. This value is in units of seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.343.6.17.2.1.1 |
es400ChassisInfoTotalNumOfPortThe number of ports within this switch. This value is the sum
of the ports within this switch.ro INTEGER .1.3.6.1.4.1.343.6.17.2.1.2 |
es400ChassisInfoNumOfPortInUseThe number of ports in this switch connected to the segment or
the end stations.ro INTEGER .1.3.6.1.4.1.343.6.17.2.1.3 |
es400ChassisInfoConsoleInUseThis usage indication of console system.ro Enumeration .1.3.6.1.4.1.343.6.17.2.1.4 |
es400ChassisInfoFrontPanelLedStatusThis object is a set of LED indications. The first two octets is
defined as system LED. The first LED is power LED. The second LED
is status LED. The other octets following the second octets
are the port LED. Every two bytes are presented to a port. The first
byte is presentd to the Link/Activity LED. The second byte is presented
to the Speed LED.
There is one byte per LED.
The most significant bit is used for blink/solid:
Off = The LED is lit permanently.
On = The LED blinks.
The three least significant bits are used for color:
1 = not lit,
2 = green,
3 = yellow,(orange)
4 = blue,
5 = red,
0+6+7 not used
The four remaining bits are currently unused and must be 0.ro OCTET STRING .1.3.6.1.4.1.343.6.17.2.1.5 |
es400ChassisInfoSaveCfgThis object indicates the status of the device configuration.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each
of the following values.
proceeding(2) - the device configuration is saving into the NV-RAM.
completed(3) - all of the device configuration parameters have been
saved into NV-RAM.
changed-not-save - some of the device configuration parameters have
been changed but not saved into NV-RAM.
failed(5) - The processing of saving device configuration is failed.ro Enumeration .1.3.6.1.4.1.343.6.17.2.1.6 |
es400ChassisConfig OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.2.2 |
es400ChassisConfigStpStateThis object can be enabled or disabled spanning tree algorithm
during runtime of the system.When the device is in 802.1Q Vlan
mode, this object will be enabled and cannot be disabled.rw Enumeration .1.3.6.1.4.1.343.6.17.2.2.1 |
es400ChassisConfigIGMPCaptureStateThis object indicates Internet Group Management Protocol (IGMP) capture
function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.343.6.17.2.2.2 |
es400ChassisConfigPartitionModeStateThis object used to enable or disable port auto partition. When the
object apply for all ports of the devicerw Enumeration .1.3.6.1.4.1.343.6.17.2.2.3 |
es400ChassisConfigTableLockStateThis object indicates whether the address table is locked.
In other words, the address table doesn't learn any more new address.
The aging timer is suspended when the address table is locked. As long
as the table is locked, all of the frames are dropped if the destination
can not be found in the address.rw Enumeration .1.3.6.1.4.1.343.6.17.2.2.4 |
es400ChassisConfigSaveCfgAs the object is set, the current device configuration is save
into to NV-RAM.rw INTEGER .1.3.6.1.4.1.343.6.17.2.2.5 |
es400ChassisConfigHOLStateThe object provides a way to prevent HOL (Head Of Line) blocking
between ports. HOL protection may prevent forwarding a packet to
a blocking port.The idea relies on the assumption that it is better
to discard packets destined to blocking ports, then to let them consume
more and more buffers in the input-port's Rx-counters because eventually
these input ports may become totally blocked. The meanings of the values
are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - HOL function disable for device.
enabled(3) - HOL function enable for device.rw Enumeration .1.3.6.1.4.1.343.6.17.2.2.6 |
es400ChassisConfigAddrLookupModesThe object provides a way to select the algorithm that optimizes the lookup
depending on the network configuration. The setting will be effective after
next system reboot.
The meanings of the values are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
sequential-mode(2) - Uses MAC address, optimized for sequential address (basic mode
or tag mode).
random-mode(3) - Uses MAC address, optimized for random address (basic mode or tag
mode).rw Enumeration .1.3.6.1.4.1.343.6.17.2.2.7 |
es400ChassisConfigUploadImageFileNameThe name of the image file to be uploaded from the device to TFTP server
when enabling image upload function (by writing es400ChassisConfigUploadImage).rw DisplayString .1.3.6.1.4.1.343.6.17.2.2.8 |
es400ChassisConfigUploadImageImage file upload control. Writing it by any value will
immediately invoke image upload function.rw INTEGER .1.3.6.1.4.1.343.6.17.2.2.9 |
es400ChassisConfigHighPriorityServiceRatioThe object provides a way to select an internal round-robin priority
weight between low-priority queue and high-priority queue.
The meanings of the values are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
pkt-1high-1low(2) - 1 pkt transmitted from HIGH, 1 pkt from LOW.
pkt-4high-1low(3) - 4 pkt transmitted from HIGH, 1 pkt from LOW.
pkt-8high-1low(4) - 8 pkt transmitted from HIGH, 1 pkt from LOW.
pkt-12high-1low(5) - 12 pkt transmitted from HIGH, 1 pkt from LOW.
all-high-before-low(6) - all pkt transmitted from HIGH, 0 pkt from LOW.
LOW will be served only if HIGH is empty. If HIGH queue is emptied
before finishing the count, the count will be reset until next
first HIGH comes in.rw Enumeration .1.3.6.1.4.1.343.6.17.2.2.10 |
es400ChassisAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.2.3 |
es400ChassisAlarmPartitionDepending on this object, the device send a trap or not when
any one of the device's ports was partitioned.rw Enumeration .1.3.6.1.4.1.343.6.17.2.3.1 |
es400ChassisAlarmNewRootWhen the device has become the new root of the Spanning Tree, this
object decide whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.343.6.17.2.3.2 |
es400ChassisAlarmTopologyChangeThis object determine to send a trap or not when the switch topology
was changed. If the object is enabled(3), the topologyChange trap is
sent by the device when any of its configured ports transitions from
the Learning state to the Forwarding state, or from the Forwarding state
to the Blocking state. For the same port tranition, the device doesn't
send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.343.6.17.2.3.3 |
es400ChassisAlarmLinkChangeThis object determine to send a trap or not when the link
was changed. If the object is enabled(3), the Link Change trap is
sent by the device when any of its ports link change. The device doesn't
send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.343.6.17.2.3.4 |
es400Port OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.3 |
es400PortInfoTableA table that contains information about every port. SEQUENCE OF Es400PortInfoEntry .1.3.6.1.4.1.343.6.17.3.1 |
es400PortInfoEntryA list of information for each port of the device. Es400PortInfoEntry .1.3.6.1.4.1.343.6.17.3.1.1 |
es400PortInfoIndexThis object indicates switch port number.(1..Max port number)ro INTEGER .1.3.6.1.4.1.343.6.17.3.1.1.1 |
es400PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.343.6.17.3.1.1.2 |
es400PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.343.6.17.3.1.1.3 |
es400PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.343.6.17.3.1.1.4 |
es400PortInfoFlowCtrlStatusThis object indicates the port flow control status.ro Enumeration .1.3.6.1.4.1.343.6.17.3.1.1.5 |
es400PortConfigTableA table that contains control information about every port. SEQUENCE OF Es400PortConfigEntry .1.3.6.1.4.1.343.6.17.3.2 |
es400PortConfigEntryA list of control information for each port of the device. Es400PortConfigEntry .1.3.6.1.4.1.343.6.17.3.2.1 |
es400PortConfigIndexThis object indicates the device port number.(1..Max port number)ro INTEGER .1.3.6.1.4.1.343.6.17.3.2.1.1 |
es400PortConfigAdminStateThis object decide the port enabled or disabled.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.2 |
es400PortConfigLinkStatusAlarmStateDepending on this object to determine to send a trap or
not when link status changes .rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.3 |
es400PortConfigNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.4 |
es400PortConfigFlowCtrlStateSet IEEE 802.3x compliant flow control function as enabled or disabled.
And IEEE 802.3x compliant flow control function work only when the port
is in full duplex mode.If the port is set Auto-negotiation enabled, the
object stands for flow control capability. The results should be referred
to es400PortInfoFlowCtrlStatus object. If the port is in force mode,
this objects is simply used to set the flow control state (on/off). In
force mode, if you change it from enabled to disabled state, it will work
after next system restart. But the flow control changing from disabled to
enabled state, it will immediately work.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.5 |
es400PortConfigBackPressStateDepending on this object determine to enable or disable the
backpressure function when the port is working in half duplex mode.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.6 |
es400PortConfigLockStateThe state of this entry. When the es400ChassisConfigTableLockState
object is enabled, the state is not changed. The meanings of the
values are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
disable(2) - Port lock funtion disable.
enable(3) - Locking a port. Once the port is locked, it will not
learn new SA addresses, and drop unknown/moved-SA packets
forwarding to/from such ports. This is a way to prevent
undesired traffic from being received or transmmited on
the port. Note that locking a port doesn't lock the MAC
address entries associated with the locked port, i.e. the
existing address entries of the locked port will be age
out even though it is locked.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.7 |
es400PortConfigPriorityThe priority queueing for packets received on this port, except for
BPDU/IGMP packets and packets with unknown unicast destination address.
IGMP and BPDU packets are always routed with high priority; packets with
unknown unicast destination addresses are always routed with low priority.
Other packets follow the rules below:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
default(2) - A packet is normally classified as low priority
,unless at least one of the following is true:
.The packet contained a TAG (per 802.1Q definition) with the
priority greater or equal to 4.
.The address-table entry for the destination address had Pd=HIGH.
force-low_priority(3) - A packet is normally classified as low priority.
force-high_priority(4) - A packet is normally classified as high
priority.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.8 |
es400PortConfigStpStateThe state of STP(spanning tree algorithm) operation on this port. That's
meaning the port whether add in the STP. The value enabled(3) indicates
that STP is enabled on this port, as long as es400ChassisConfigStpState
is also enabled for this device.When disabled(2) but es400ChassisConfigStpState
is still enabled for the device, STP is disabled on this port : any BPDU
packets received will be discarded and no BPDU packets will be propagated
from the port.When the device is in 802.1Q Vlan mode, this object will be
enabled and cannot be disabled.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.9 |
es400PortConfigHOLStateThe object provides a way to prevent HOL (Head Of Line) blocking
between ports. HOL protection may prevent forwarding a packet to
a blocking port.The idea relies on the assumption that it is better
to discard packets destined to blocking ports, then to let them consume
more and more buffers in the input-port's Rx-counters because eventually
these input ports may become totally blocked. The value enabled(3)
indicates that HOL function is enabled on this port, as long as
es400ChassisConfigHOLState is also enabled for this device. When
disabled(2) but es400ChassisConfigHOLState is still enabled for the
device, HOL function is disabled on this port. The meanings of the
values are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - HOL function disable.
enabled(3) - HOL function enable.rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.10 |
es400PortConfigBroadcastStormThrThis object contains the setting of the broadcast storm threshold
control on each port. The threshold value is represented by the
percentage of the port's total bandwidth used by broadcast traffic.
The broadcast storm control function is enabled/disabled by
es400PortConfigBroadcastStormCtrl object. When broadcast storm control
function is enabled, if broadcast traffic for a port rises above the
threshold, the port will be blocked and a trap is sent to management
user. When the broadcast storm traffic falls below the threshold, the
blocked port will forward packets again and a trap is sent to management
user too. The maximum value is 20rw INTEGER .1.3.6.1.4.1.343.6.17.3.2.1.11 |
es400PortConfigBroadcastStormCtrlThis object indicates whether to enable the broadcast storm control.
Refer to es400PortConfigBroadcastStormThr for details.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - disable the broadcast storm control function .
enabled(3) - enable the broadcast storm control function .rw Enumeration .1.3.6.1.4.1.343.6.17.3.2.1.12 |
es400PortConfigCleanAllStatisticCounterSetting this object will reset current device's all statistic counters.rw INTEGER .1.3.6.1.4.1.343.6.17.3.2.1.13 |
es400PortStatTableA list of port statistic Counter entries. SEQUENCE OF Es400PortStatEntry .1.3.6.1.4.1.343.6.17.3.3 |
es400PortStatEntryThis entry include all the port statistic Counter which support
by the device, like Bytes received, Bytes Sent ... Es400PortStatEntry .1.3.6.1.4.1.343.6.17.3.3.1 |
es400PortStatIndexThis object indicates the device port number.(1..Max port number)ro INTEGER .1.3.6.1.4.1.343.6.17.3.3.1.1 |
es400PortStatByteRxes400ChassisConfigCounterMode = 2(switched-frames):This counter is incre-
mented once for every data octet of good packets(unicast + multi-
cast + broadcast) received.
es400ChassisConfigCounterMode = 3(all-frames):This counter is incremented
once for every data octet of good packets(unicast + multicast +
broadcast packets) and for local and dropped packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.2 |
es400PortStatByteTxThis counter is incremented once for every data octet of a trans-
mitted good packet.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.3 |
es400PortStatFrameRxes400ChassisConfigCounterMode = 2(switched-frames):This counter is incre-
mented once for every good packet(unicast + multicast + broadcast
) received.
es400ChassisConfigCounterMode = 3(all-frames):This counter is incremented
once for every good packet(unicast + multicast + broadcast packets)
and for local and dropped packets received.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.4 |
es400PortStatFrameTxThis counter is incremented once for every transmitted good packet.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.5 |
es400PortStatTotalBytesRxThis counter is incremented once for every data octet of all
received packets. This include data octets of rejected and local
packets which are not forwarded to the switching core for trans-
mission. This counter should reflect all the data octets received
on the line. Note: A nibble is not counted as a whole byte.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.6 |
es400PortStatTotalFramesRxThis counter is incremented once for every received packets. This
include rejected and local packets which are not forwarded to the
switching core for transmission. This counter should reflect all
packets received on the line.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.7 |
es400PortStatBroadcastFramesRxes400ChassisConfigCounterMode = 2(switched-frames):This counter is incre-
mented once for every good broadcast packet received.
es400ChassisConfigCounterMode = 3(all-frames):This counter is incremented
once for every good broadcast packet received and for local and
dropped broadcast packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.8 |
es400PortStatMulticastFramesRxes400ChassisConfigCounterMode = 2(switched-frames):This counter is incre-
mented once for every good multicast packet received.
es400ChassisConfigCounterMode = 3(all-frames):This counter is incremented
once for every good multicast packet received and for local and
dropped multicast packets. This counter does not include broad-
cast packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.9 |
es400PortStatCRCErrorThis counter is incremented once for every received packet which
meets all the following conditions:
1.Packet data length is between 64 and 1518 bytes inclusive.
2.Packet has invalid CRC.
3.Collision event , late collision event and receive error event
have not been detected.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.10 |
es400PortStatOversizeFramesThe number of good frames with length more than 1518 bytes.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.11 |
es400PortStatFragmentsThis counter is incremented once for every received packet which
meets all the following conditions:
1.Packet data length is less than 64 bytes or packet withourt SFD
and is less than 64 bytes in length.
2.Packet has invalid CRC.
3.Collision event , late collision event and receive error event
have not been detected.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.12 |
es400PortStatJabberThe number of frames with length more than 1518 bytes and with
CRC error or misaligned.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.13 |
es400PortStatCollisionThe number of Collisionsro Counter .1.3.6.1.4.1.343.6.17.3.3.1.14 |
es400PortStatLateCollisionThe number of Late Collision(collision occurring later than
576th transmitted bit).ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.15 |
es400PortStatFrames-64-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 64 bytes. This counter includes reject-
ed received and transmitted packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.16 |
es400PortStatFrames-65-127-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 65 to 127 bytes. This counter includes
rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.17 |
es400PortStatFrames-128-255-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 128 to 255 bytes. This counter includes
rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.18 |
es400PortStatFrames-256-511-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 256 to 511 bytes. This counter includes
rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.19 |
es400PortStatFrames-512-1023-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 512 to 1023 bytes. This counter includ-
es rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.20 |
es400PortStatFrames-1024-1536-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 1024 to 1536 bytes. This counter includ-
es rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.21 |
es400PortStatFramesDroppedFramesThis counter is incremented once for every received dropped pack-
et.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.22 |
es400PortStatMulticastFramesTxThe number of multicast frames sent. This counter does not include
broadcast packets.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.23 |
es400PortStatBroadcastFramesTxThe number of broadcast frames sent.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.24 |
es400PortStatUndersizeFramesThis counter is incremented once for every received packet which
meets all the following conditions:
1.Packet data length is less than 64 bytes.
2.Packet has valid CRC.
3.Collision event , late collision event and receive error event
have not been detected.ro Counter .1.3.6.1.4.1.343.6.17.3.3.1.25 |
es400FDb OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.4 |
es400FDbStaticTableLike typical legacy bridge devices, FDB table records the mapping
of Source MAC Address and its associated source port, and forward
incoming packets to its destination port according to the Destination
MAC Address of the packet as well as the MAC-port pair entries of the
FDB table. Note that the priority of FDB table entries is lower
than Filtering Table, i.e. if there is a table hash collision between
the entries of FDB Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the colliding entry
of FDB Table. See es400FDbFilterTable description also. SEQUENCE OF Es400FDbStaticEntry .1.3.6.1.4.1.343.6.17.4.1 |
es400FDbStaticEntryA list of information specifies which ports the frames with specific
destination MAC address to go. Es400FDbStaticEntry .1.3.6.1.4.1.343.6.17.4.1.1 |
es400FdbStaticVidThis object indicates the VLAN-ID. If the es400VlanInfoStatus
is port-base mode , the object ranges from 1 to 12. If VLAN
is in mac-based mode or disabled, the object indicates the
default VLAN-ID (0).ro INTEGER .1.3.6.1.4.1.343.6.17.4.1.1.1 |
es400FDbStaticAddressIndexThe destination MAC address in a frame to which this entry's
forwarding information applies. This object can take the value of
an unicast address or the multicast address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.343.6.17.4.1.1.2 |
es400FDbStaticPortMapThe set of ports to which frames received from a specific port
and destined for a specific MAC address, are allowed to be
forwarded. Each octet within the value of this object specifies
a set of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents the lowest
numbered port, and the least significant bit represents the highest
numbered port. Thus, each port of the bridge is represented by
a single bit within the value of this object. If that bit has a
value of '1' then that port is included in the set of ports; the
port is not included if its bit has a value of '0'.(Note that the
setting of the bit corresponding to the port from which a frame
is received is irrelevant.)rw OCTET STRING .1.3.6.1.4.1.343.6.17.4.1.1.3 |
es400FDbStaticStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
invalid(2) - writing this value to the object, and then the corresponding
entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.343.6.17.4.1.1.4 |
es400FDbStaticStatusThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
apply(2) - this entry is currently in use and reside in the table.
not-apply(3) - this entry is reside in the table but currently not
in use due to conflict with filter table.ro Enumeration .1.3.6.1.4.1.343.6.17.4.1.1.5 |
es400FDbFilterTableA table which contains the filtering information of the
unicast/multicast entries. This table is used by the transparent
switching function in determining how to filter the received frames.
The Filtering Table entries' priority overrides Static FDB Table
as well as IGMP table entries, say, if there is a hash table entry
collision between Filtering Table and Static FDB Table setting in
the switch device's H/W address table, then Filter Table entry setting
overwrites the colliding entry in Static FDB Table. See
es400FDbStaticTable description also. SEQUENCE OF Es400FDbFilterEntry .1.3.6.1.4.1.343.6.17.4.2 |
es400FDbFilterEntryA list of information about a specific unicast/multicast MAC address
for which the switch has filtering information. Es400FDbFilterEntry .1.3.6.1.4.1.343.6.17.4.2.1 |
es400FdbFilterVidThis object indicates the VLAN-ID. If the es400VlanInfoStatus
is port-base mode , the object ranges from 1 to 12. If VLAN
is in mac-based mode or disabled, the object indicates the
default VLAN-ID (0).ro INTEGER .1.3.6.1.4.1.343.6.17.4.2.1.1 |
es400FDbFilterAddressIndexThis object indicates a unicast/multicast MAC address for which the bridge
has filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.343.6.17.4.2.1.2 |
es400FDbFilterStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
dst-src-addr(2) - recieved frames's destination address or source
address are currently used to be filtered as it meets with
the MAC address entry of the table.
invalid(3) - writing this value to the object, and then the corresponding
entry will be removed from the table.rw Enumeration .1.3.6.1.4.1.343.6.17.4.2.1.3 |
es400LinkAggr OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.5 |
es400LinkAggrTableThis table specifys which ports group a set of ports(up to 8)
into a single logical link. SEQUENCE OF Es400LinkAggrEntry .1.3.6.1.4.1.343.6.17.5.1 |
es400LinkAggrEntryA list of information specifies which ports group a set of
ports(up to 8) into a single logical link. Es400LinkAggrEntry .1.3.6.1.4.1.343.6.17.5.1.1 |
es400LinkAggrIndexThe index of logical port trunk.The device max support 4 trunk groups.
The trunk group number depend on the total number of device ports and
the existence of module.ro INTEGER .1.3.6.1.4.1.343.6.17.5.1.1.1 |
es400LinkAggrNameThe name of logical port trunk.rw DisplayString .1.3.6.1.4.1.343.6.17.5.1.1.2 |
es400LinkAggrMasterPortThe object indicates the master port number of the port trunk entry.The
first port of the trunk is implicitly configured to be the master logical
port.When using Port Trunk, you can not configure the other ports of
the group except the master port. Their configuration must be same as the
master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).ro INTEGER .1.3.6.1.4.1.343.6.17.5.1.1.3 |
es400LinkAggrMemberNumIndicate how many number of ports is included in this Trunk. If
the trunk is located at expansion module (i.e. es400LinkAggrIndex
equals to 4(24 ports) or 3(16 ports)) and the module is 100-FX,
the maximum number of ports in the trunk is 2. The maximum number
of ports is 8 for other trunks.rw INTEGER .1.3.6.1.4.1.343.6.17.5.1.1.4 |
es400LinkAggrStateThis object decide the port trunk enabled or disabled.rw Enumeration .1.3.6.1.4.1.343.6.17.5.1.1.5 |
es400PortMirror OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.6 |
es400PortMirrorCtrlTableA list of port snooping entries.Port snooping function provide an easy
way to monitor traffic on any port. In this way any good packets appears
on the source mirror port also shows up on the target mirror port and
doesn't to reconstruct the LAN. SEQUENCE OF Es400PortMirrorCtrlEntry .1.3.6.1.4.1.343.6.17.6.1 |
es400PortMirrorCtrlEntryA list of information provide an easy way to monitor traffic on any port.
The use can bring a fancy network monitor attaching to any target mirror
port and set the port to be monitored as source mirror port. Es400PortMirrorCtrlEntry .1.3.6.1.4.1.343.6.17.6.1.1 |
es400PortMirrorCtrlIndexThis object indicates the port snooping entry number.There is just only
one now.ro INTEGER .1.3.6.1.4.1.343.6.17.6.1.1.1 |
es400PortMirrorCtrlSourcePortThis object indicates switch which port will be mirrored.rw INTEGER .1.3.6.1.4.1.343.6.17.6.1.1.2 |
es400PortMirrorCtrlTargetPortThis object indicates switch which port will sniff another port.
A aggregate port member cannot be configured as a target mirroring
port.rw INTEGER .1.3.6.1.4.1.343.6.17.6.1.1.3 |
es400PortMirrorCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
disable(2) - Mirror funtion disable.
enable(3) - Mirror funtion enable and mirror received or transmit
packet by mirror source port.rw Enumeration .1.3.6.1.4.1.343.6.17.6.1.1.4 |
es400IgmpSnoop OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.7 |
es400IgmpSnoopConfigTableThe table controls the Vlan's IGMP function. Its scale depends on
current VLAN state (es400VlanInfoStatus). If VLAN is disabled or
in Mac-Base mode, there is only one entry in the table, with
index 1. If VLAN is in Port-Base or 802.1q mode, the number of
entries can be up to 12, with index range from 1 to 12. When in
802.1q mode, this entry table is only valid in static registration
entries. SEQUENCE OF Es400IgmpSnoopConfigEntry .1.3.6.1.4.1.343.6.17.7.1 |
es400IgmpSnoopConfigEntryThe entry in IGMP control table (es400IgmpSnoopConfigTable). The
entry is effective only when IGMP capture switch (es400Chassis-
ConfigIGMPCaptureState) is enabled. Es400IgmpSnoopConfigEntry .1.3.6.1.4.1.343.6.17.7.1.1 |
es400IgmpSnoopConfigIndexThis object indicates the IGMP control entry number.Its scale depends on
current VLAN state (es400VlanInfoStatus). If VLAN is disabled or in
Mac-Base mode, there is only one entry in the table, with index 1.
If VLAN is in Port-Base or 802.1q mode, the number of entries is 12,
with index range from 1 to 12.ro INTEGER .1.3.6.1.4.1.343.6.17.7.1.1.1 |
es400IgmpSnoopConfigVidThis object indicates the IGMP control entry's VLAN id. If VLAN is
disabled or in Mac-Base mode, the Vid is always 0 and cannot be changed
by management users. If VLAN is in Port-Base mode, the Vid is arranged
from 1 to 12 , fixed form. If VLAN is in 802.1q mode, the Vid setting
can vary from 1 to 4094 by management user, and the Vid in each entry
must be unique in the IGMP Control Table.rw INTEGER .1.3.6.1.4.1.343.6.17.7.1.1.2 |
es400IgmpSnoopConfigTimerThe timer value for sending IGMP query packet when none
was sent by the multicast router in the LAN. The timer works
in per-VLAN basis. Our device will be activated to send the query
message if the timer is expired. Please reference RFC2236-1997.
And it recommends a default of 125 seconds. The timeout value must
be at least 30 seconds.rw INTEGER .1.3.6.1.4.1.343.6.17.7.1.1.3 |
es400IgmpSnoopConfigStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
disable(2) - IGMP funtion is disabled for this entry.
enable(3) - IGMP funtion is enabled for this entry.rw Enumeration .1.3.6.1.4.1.343.6.17.7.1.1.4 |
es400IgmpSnoopInfoTableThe table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device. SEQUENCE OF Es400IgmpSnoopInfoEntry .1.3.6.1.4.1.343.6.17.7.2 |
es400IgmpSnoopInfoEntryInformation about current IGMP query information, provided that
es400ChassisConfigIGMPCaptureState and es400IgmpSnoopConfigState of
associated VLAN entry are all enabled. Es400IgmpSnoopInfoEntry .1.3.6.1.4.1.343.6.17.7.2.1 |
es400IgmpSnoopInfoIndexThis object indicates the IGMP query information entry number. It could
be up to 12 entries, depending on current number of VLAN entries.ro INTEGER .1.3.6.1.4.1.343.6.17.7.2.1.1 |
es400IgmpSnoopInfoVidThis object indicates the Vid of associated IGMP info table entry. It
follows es400IgmpSnoopConfigVid in the associated entry of IGMP control
table (es400IgmpSnoopConfigTable).ro INTEGER .1.3.6.1.4.1.343.6.17.7.2.1.2 |
es400IgmpSnoopInfoQueryCountThis object indicates the number of query packets received since the
IGMP function enabled, in per-VLAN basis.ro INTEGER .1.3.6.1.4.1.343.6.17.7.2.1.3 |
es400IgmpSnoopInfoTxQueryCountThis object indicates the send count of IGMP query messages, in
per-VLAN basis. In case of IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and increment
this object by 1.ro INTEGER .1.3.6.1.4.1.343.6.17.7.2.1.4 |
es400IgmpSnoopTableThe table containing current IGMP information which captured by this
device, provided that es400ChassisConfigIGMPCaptureState and
es400IgmpSnoopConfigState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering Table,
i.e. if there is a table hash collision between the entries of IGMP Table
and Filtering Table inside the switch H/W address table, then Filtering
Table entry overwrite the colliding entry of IGMP Table. See
es400FDbFilterTable description also. SEQUENCE OF Es400IgmpSnoopEntry .1.3.6.1.4.1.343.6.17.7.3 |
es400IgmpSnoopEntryInformation about current IGMP information which captured by this
device , provided that es400ChassisConfigIGMPCaptureState and
es400IgmpSnoopConfigState of associated VLAN entry are all enabled. Es400IgmpSnoopEntry .1.3.6.1.4.1.343.6.17.7.3.1 |
es400IgmpSnoopVidThis object indicates the Vid of individual IGMP table entry. It
shows the Vid of IGMP report information captured on network.ro INTEGER .1.3.6.1.4.1.343.6.17.7.3.1.1 |
es400IgmpSnoopGroupIpAddrThis object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis.ro IpAddress .1.3.6.1.4.1.343.6.17.7.3.1.2 |
es400IgmpSnoopMacAddrThis object is identify mac address which is corresponding
to es400IgmpSnoopGroupIpAddr, in per-Vlan basis..ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.343.6.17.7.3.1.3 |
es400IgmpSnoopPortMapThis object indicates which ports are belong to the same multicast
group, in per-Vlan basis. Each multicast group has a octect string
to indicate with port map. The most significant bit represents the
lowest numbered port, and the least significant bit represents the
highest numbered port.ro PortList .1.3.6.1.4.1.343.6.17.7.3.1.4 |
es400IgmpSnoopReportCountThis object indicate how much report packet was receive by our
device corresponding with this entry from IGMP function enabled,
in per-Vlan basis.ro INTEGER .1.3.6.1.4.1.343.6.17.7.3.1.5 |
es400Vlan OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.8 |
es400VlanConfigModeThis object control which Vlan function will be enable (or disable)
when the switch hub restart at the startup (power on) or warm
start.rw Enumeration .1.3.6.1.4.1.343.6.17.8.1 |
es400VlanInfoStatusThis object indicate which Vlan function be enable (or disable)
in mandatoryly stage. There are no effect when change es400VlanConfigMode
vlaue in the system running.ro Enumeration .1.3.6.1.4.1.343.6.17.8.2 |
es400VlanSnmpPortInfoThis object controls which Vlan is binded with system snmp port.
Its scale depends on current VLAN state (es400VlanInfoStatus).
If VLAN is disabled or in Mac-Base mode, the Vid is always 0
and cannot be changed by management users. If VLAN is in 802.1q
mode, the Vid setting can vary from 1 to 4094 by management user.
If VLAN is in Port-Base mode, the Vid setting can vary from 1 to
12 by management user.rw VlanIndex .1.3.6.1.4.1.343.6.17.8.3 |
es400MacVlan OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.8.4 |
es400MacVlanTotalNumThe total number of Mac base Vlan within this switch hub.ro INTEGER .1.3.6.1.4.1.343.6.17.8.4.1 |
es400MacVlanConfigTableA table that contains MAC-Based VLAN list entries for the switch.
Management users can create a MAC-Based VLAN entry by adding a new
list (es400MacVlanConfigEntry) in this table. SEQUENCE OF Es400MacVlanConfigEntry .1.3.6.1.4.1.343.6.17.8.4.2 |
es400MacVlanConfigEntryA list of information about a specific MAC-Based VLAN configuration
in es400MacVlanConfigTable. Es400MacVlanConfigEntry .1.3.6.1.4.1.343.6.17.8.4.2.1 |
es400MacVlanDescA textual description of the Mac Base Vlan.ro DisplayString .1.3.6.1.4.1.343.6.17.8.4.2.1.1 |
es400MacVlanMacMemberNumThis object indicates the total number of MAC addresses contained
in the VLAN entry.ro INTEGER .1.3.6.1.4.1.343.6.17.8.4.2.1.2 |
es400MacVlanCtrlStateThis object indicates the MacBase Vlan state. Writing disabled
value to the object will remove the corresponding entry from the
table.rw Enumeration .1.3.6.1.4.1.343.6.17.8.4.2.1.3 |
es400MacVlanAddrTotalNumThe total number of Mac base Vlan address entry within this switch
hub.ro INTEGER .1.3.6.1.4.1.343.6.17.8.4.3 |
es400MacVlanAddrTableA table that contains information about unicast entries for which
the switch has forwarding and/or filtering information. This
information is used by the transparent switching function in
determining how to propagate a received frame. Note that the
priority of MacVlanAddr table entries is lowest than Filtering
Table and FDB Table, i.e. if there is a table hash collision between
the entries of MacVlanAddr Table and Filtering Table inside the switch
H/W address table, then Filtering Table entry overwrite the colliding
entry of MacVlanAddr Table. This state is same of FDB table. See
es400FDbFilterTable and es400FDbStaticTable
description also. SEQUENCE OF SwMacBaseVlanAddrEntry .1.3.6.1.4.1.343.6.17.8.4.4 |
es400MacVlanAddrEntryA list of information about a specific unicast MAC address for which
the switch has some forwarding and/or filtering information. SwMacBaseVlanAddrEntry .1.3.6.1.4.1.343.6.17.8.4.4.1 |
es400MacVlanAddressThis object indictaes a unicast MAC address for which the bridge
has forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.343.6.17.8.4.4.1.1 |
es400MacVlanAddrDescThis object references to the MAC-Base VLAN description (es400MacVlanDesc)
which the MAC address belong to. You must update the VLAN description
with an VLAN description which is already exist on MAC-Base VLAN control
table. If the VLAN description on the MAC-Base VLAN control table doesn't
exist , the corresponding entry will be removed from the table.rw DisplayString .1.3.6.1.4.1.343.6.17.8.4.4.1.2 |
es400MacVlanAddrStateThis object indicates the MacBase Vlan Address entry state.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
invalid(2) - writing this value to the object, and then the corresponding
entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.343.6.17.8.4.4.1.3 |
es400MacVlanAddrStatusThis object indicates the MacBase Vlan Address entry state.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
apply(2) - this entry is currently in use and reside in the table.
not-apply(3) - this entry is reside in the table but currently not
in use due to conflict with filter table.ro Enumeration .1.3.6.1.4.1.343.6.17.8.4.4.1.4 |
es400PortVlan OBJECT IDENTIFIER .1.3.6.1.4.1.343.6.17.8.5 |
es400PortVlanTotalNumThe total number of Port-Base Vlan which is in enabled state
within this switch hub.ro INTEGER .1.3.6.1.4.1.343.6.17.8.5.1 |
es400PortVlanDefaultVlanTableA table that contains default Port-Based VLAN list entries for the
switch. The entry (Vid = 1,i.e. es400PortVlanDefaultPvid = 1) is
defalut Port-Based VLAN , maintained by system. SEQUENCE OF Es400PortVlanDefaultVlanEntry .1.3.6.1.4.1.343.6.17.8.5.2 |
es400PortVlanDefaultVlanEntryA list of default Port-Based VLAN information in
es400PortVlanDefaultVlanTable. Es400PortVlanDefaultVlanEntry .1.3.6.1.4.1.343.6.17.8.5.2.1 |
es400PortVlanDefaultPvidThis object indicates the default Port-Base Vlan ID. It occupies only
1 entry in VLAN table, with VID=1.ro INTEGER .1.3.6.1.4.1.343.6.17.8.5.2.1.1 |
es400PortVlanDefaultDescA textual description of the Port-Base Vlan.ro DisplayString .1.3.6.1.4.1.343.6.17.8.5.2.1.2 |
es400PortVlanDefaultPortListThis object indicates the port member set of the specified Vlan.
Each Vlan has a octect string to indicate the port map. The most
significant bit represents the lowest numbered port, and the
least significant bit represents the highest numbered port.ro PortList .1.3.6.1.4.1.343.6.17.8.5.2.1.3 |
es400PortVlanDefaultPortNumberThis object indicates the number of ports of the entry.ro INTEGER .1.3.6.1.4.1.343.6.17.8.5.2.1.4 |
es400PortVlanConfigTableA table that contains Port-Based VLAN list entries for the switch.
The device can't support port overlapping in Port-Based VLAN. SEQUENCE OF Es400PortVlanConfigEntry .1.3.6.1.4.1.343.6.17.8.5.3 |
es400PortVlanConfigEntryA list of information about a specific Port-Based VLAN configuration
in es400PortVlanConfigTable. Es400PortVlanConfigEntry .1.3.6.1.4.1.343.6.17.8.5.3.1 |
es400PortVlanConfigPvidThis object indicates the Port-Base Vlan ID. There are up to 11 entries
for current product now. The object range varies from 2 to 12.ro INTEGER .1.3.6.1.4.1.343.6.17.8.5.3.1.1 |
es400PortVlanConfigDescA textual description of the Port-Base Vlan. It cannot be a null string.
And each description must be unique in the table.rw DisplayString .1.3.6.1.4.1.343.6.17.8.5.3.1.2 |
es400PortVlanConfigPortListThis object indicates which ports are belong to the Vlan. Each Vlan
has a octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least significant
bit represents the highest numbered port.rw PortList .1.3.6.1.4.1.343.6.17.8.5.3.1.3 |
es400PortVlanConfigPortNumberThis object indicates the number of ports of the entry.ro INTEGER .1.3.6.1.4.1.343.6.17.8.5.3.1.4 |
es400PortVlanConfigStateThis object indicates the Port-Base Vlan state.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - writing this value to the object, and then the corresponding
entry will be removed from the table.
enabled(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.343.6.17.8.5.3.1.5 |