IBM-RXR-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
208
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
208 total| Object Name |
|---|
ibm OBJECT IDENTIFIER .1.3.6.1.4.1.2 |
RFC1155-SMI Unknown .1.3.6.1.4.1.2 |
ibmProd OBJECT IDENTIFIER .1.3.6.1.4.1.2.6 |
routeXpander OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26 |
rxr1dBridge OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.1 |
newRootThe newRoot trap indicates that the sending agent
has become the new root of the Spanning Tree; the
trap is sent by a bridge soon after its election
as the new root, e.g., upon expiration of the
Topology Change Timer immediately subsequent to
its election. TRAP-TYPE .1.3.6.1.4.1.2.6.26.1.0.1 |
topologyChangeA topologyChange trap is sent by a bridge when
any of its configured ports transitions from the
Learning state to the Forwarding state, or from
the Forwarding state to the Blocking state. The
trap is not sent if a newRoot trap is sent for the
same transition. TRAP-TYPE .1.3.6.1.4.1.2.6.26.1.0.2 |
rxr1dBase OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.1.1 |
rxr1dBaseBridgeAddressThe MAC address used by this bridge when it must
be referred to in a unique fashion. It is
recommended that this be the numerically smallest
MAC address of all ports that belong to this
bridge. However it is only required to be unique.
When concatenated with rxr1dStpPriority a unique
BridgeIdentifier is formed which is used in the
Spanning Tree Protocol.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2.6.26.1.1.1 |
rxr1dBaseNumPortsThe number of ports controlled by this bridging
entity.ro INTEGER .1.3.6.1.4.1.2.6.26.1.1.2 |
rxr1dBaseTypeIndicates what type of bridging this bridge can
perform. If a bridge is actually performing a
certain type of bridging this will be indicated by
entries in the port table for the given type.ro Enumeration .1.3.6.1.4.1.2.6.26.1.1.3 |
rxr1dBasePortTableA table that contains generic information about
every port that is associated with this bridge.
Transparent, source-route, and srt ports are
included. SEQUENCE OF Rxr1dBasePortEntry .1.3.6.1.4.1.2.6.26.1.1.4 |
rxr1dBasePortEntryA list of information for each port of the
bridge. Rxr1dBasePortEntry .1.3.6.1.4.1.2.6.26.1.1.4.1 |
rxr1dBasePortThe port number of the port for which this entry
contains bridge management information.ro INTEGER .1.3.6.1.4.1.2.6.26.1.1.4.1.1 |
rxr1dBasePortIfIndexThe value of the instance of the ifIndex object,
defined in [4,6], for the interface corresponding
to this port.ro INTEGER .1.3.6.1.4.1.2.6.26.1.1.4.1.2 |
rxr1dBasePortCircuitFor a port which (potentially) has the same value
of rxr1dBasePortIfIndex as another port on the
same bridge, this object contains the name of an
object instance unique to this port. For example,
in the case where multiple ports correspond one-
to-one with multiple X.25 virtual circuits, this
value might identify an (e.g., the first) object
instance associated with the X.25 virtual circuit
corresponding to this port.
For a port which has a unique value of
rxr1dBasePortIfIndex, this object can have the
value { 0 0 }.ro OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.1.1.4.1.3 |
rxr1dBasePortDelayExceededDiscardsThe number of frames discarded by this port due
to excessive transit delay through the bridge. It
is incremented by both transparent and source
route bridges.ro Counter .1.3.6.1.4.1.2.6.26.1.1.4.1.4 |
rxr1dBasePortMtuExceededDiscardsThe number of frames discarded by this port due
to an excessive size. It is incremented by both
transparent and source route bridges.ro Counter .1.3.6.1.4.1.2.6.26.1.1.4.1.5 |
rxr1dStp OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.1.2 |
rxr1dStpProtocolSpecificationAn indication of what version of the Spanning
Tree Protocol is being run. The value
'decLb100(2)' indicates the DEC LANbridge 100
Spanning Tree protocol. IEEE 802.1d
implementations will return 'ieee8021d(3)'. If
future versions of the IEEE Spanning Tree Protocol
are released that are incompatible with the
current version a new value will be defined.ro Enumeration .1.3.6.1.4.1.2.6.26.1.2.1 |
rxr1dStpPriorityThe value of the write-able portion of the Bridge
ID, i.e., the first two octets of the (8 octet
long) Bridge ID. The other (last) 6 octets of the
Bridge ID are given by the value of
rxr1dBaseBridgeAddress.rw INTEGER .1.3.6.1.4.1.2.6.26.1.2.2 |
rxr1dStpTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.2.6.26.1.2.3 |
rxr1dStpTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.ro Counter .1.3.6.1.4.1.2.6.26.1.2.4 |
rxr1dStpDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro BridgeId .1.3.6.1.4.1.2.6.26.1.2.5 |
rxr1dStpRootCostThe cost of the path to the root as seen from
this bridge.ro INTEGER .1.3.6.1.4.1.2.6.26.1.2.6 |
rxr1dStpRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro INTEGER .1.3.6.1.4.1.2.6.26.1.2.7 |
rxr1dStpMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Timeout .1.3.6.1.4.1.2.6.26.1.2.8 |
rxr1dStpHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.ro Timeout .1.3.6.1.4.1.2.6.26.1.2.9 |
rxr1dStpHoldTimeThis time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro INTEGER .1.3.6.1.4.1.2.6.26.1.2.10 |
rxr1dStpForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in a particular state before moving to the
next state. For example, how long a port stays in
the Listening state when moving from Blocking to
Learning. This value is also used, when a
topology change has been detected and is underway,
to age all dynamic entries in the Forwarding
Database. [Note that this value is the one that
this bridge is currently using, in contrast to
rxr1dStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]ro Timeout .1.3.6.1.4.1.2.6.26.1.2.11 |
rxr1dStpBridgeMaxAgeThe value that all bridges use for MaxAge when
this bridge is acting as the root. Note that
802.1d/D9 specifies that the range for this
parameter is related to the value of
rxr1dStpBridgeHelloTime. The granularity of this
timer is specified by 802.1d/D9 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.2.6.26.1.2.12 |
rxr1dStpBridgeHelloTimeThe value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by
802.1d/D9 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds.rw Timeout .1.3.6.1.4.1.2.6.26.1.2.13 |
rxr1dStpBridgeForwardDelayThe value that all bridges use for ForwardDelay
when this bridge is acting as the root. Note that
802.1d/D9 specifies that the range for this
parameter is related to the value of
rxr1dStpBridgeMaxAge. The granularity of this
timer is specified by 802.1d/D9 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.2.6.26.1.2.14 |
rxr1dStpPortTableA table that contains port-specific information
for the Spanning Tree Protocol. SEQUENCE OF Rxr1dStpPortEntry .1.3.6.1.4.1.2.6.26.1.2.15 |
rxr1dStpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. Rxr1dStpPortEntry .1.3.6.1.4.1.2.6.26.1.2.15.1 |
rxr1dStpPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.2.6.26.1.2.15.1.1 |
rxr1dStpPortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
rxr1dStpPort.rw INTEGER .1.3.6.1.4.1.2.6.26.1.2.15.1.2 |
rxr1dStpPortStateThe port's current state as defined by
application of the Spanning Tree Protocol. This
state controls what action a port takes on
reception of a frame. If the bridge has detected
a port that is malfunctioning it will place that
port into the broken(6) state. For ports which
are disabled (see rxr1dStpPortEnable), this object
will have a value of disabled(1).ro Enumeration .1.3.6.1.4.1.2.6.26.1.2.15.1.3 |
rxr1dStpPortEnableThe enabled/disabled status of the port.rw Enumeration .1.3.6.1.4.1.2.6.26.1.2.15.1.4 |
rxr1dStpPortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port.rw INTEGER .1.3.6.1.4.1.2.6.26.1.2.15.1.5 |
rxr1dStpPortDesignatedRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId .1.3.6.1.4.1.2.6.26.1.2.15.1.6 |
rxr1dStpPortDesignatedCostThe path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.ro INTEGER .1.3.6.1.4.1.2.6.26.1.2.15.1.7 |
rxr1dStpPortDesignatedBridgeThe Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.ro BridgeId .1.3.6.1.4.1.2.6.26.1.2.15.1.8 |
rxr1dStpPortDesignatedPortThe Port Identifier of the port on the Designated
Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.2.6.26.1.2.15.1.9 |
rxr1dStpPortForwardTransitionsThe number of times this port has transitioned
from the Learning state to the Forwarding state.ro Counter .1.3.6.1.4.1.2.6.26.1.2.15.1.10 |
rxr1dSr OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.1.3 |
rxr1dSrPortTableA table that contains information about every
port that is associated with this source route
bridge. SEQUENCE OF Rxr1dSrPortEntry .1.3.6.1.4.1.2.6.26.1.3.1 |
rxr1dSrPortEntryA list of information for each port of a source
route bridge. Rxr1dSrPortEntry .1.3.6.1.4.1.2.6.26.1.3.1.1 |
rxr1dSrPortThe port number of the port for which this entry
contains Source Route management information.ro INTEGER .1.3.6.1.4.1.2.6.26.1.3.1.1.1 |
rxr1dSrPortHopCountThe maximum number of routing descriptors allowed
in an All Paths or Spanning Tree Explorer frames.rw INTEGER .1.3.6.1.4.1.2.6.26.1.3.1.1.2 |
rxr1dSrPortLocalSegmentThe segment number that uniquely identifies the
segment to which this port is connected. Current
source routing protocols limit this value to the
range: 0 through 4095. A value of 65535 signifies
that no segment number is assigned to this port.rw INTEGER .1.3.6.1.4.1.2.6.26.1.3.1.1.3 |
rxr1dSrPortBridgeNumA bridge number uniquely identifies a bridge when
more than one bridge is used to span the same two
segments. Current source routing protocols limit
this value to the range: 0 through 15. A value of
65535 signifies that no bridge number is assigned
to this bridge.rw INTEGER .1.3.6.1.4.1.2.6.26.1.3.1.1.4 |
rxr1dSrPortTargetSegmentThe segment number that corresponds to the target
segment this port is considered to be connected to
by the bridge. Current source routing protocols
limit this value to the range: 0 through 4095. A
value of 65535 signifies that no target segment is
assigned to this port.rw INTEGER .1.3.6.1.4.1.2.6.26.1.3.1.1.5 |
rxr1dSrPortLargestFrameThe maximum size of the INFO field (LLC and
above) that this port can send/receive. It does
not include any MAC level (framing) octets. The
value of this object is used by this bridge to
determine whether a modification of the
LargestFrame (LF, see [14]) field of the Routing
Control field of the Routing Information Field is
necessary. Valid values as defined by the 802.5
source routing bridging specification[14] are 516,
1500, 2052, 4472, 8144, 11407, 17800, and 65535
octets. Behavior of the port when an illegal
value is written is implementation specific. It
is recommended that a reasonable legal value be
chosen.rw Enumeration .1.3.6.1.4.1.2.6.26.1.3.1.1.6 |
rxr1dSrPortSTESpanModeDetermines how this port behaves when presented
with a Spanning Tree Explorer frame. The value
'disabled(2)' indicates that the port will not
accept or send Spanning Tree Explorer packets; any
STE packets received will be silently discarded.
The value 'forced(3)' indicates the port will
always accept and propagate Spanning Tree Explorer
frames. This allows a manually configured
Spanning Tree for this class of packet to be
configured. Note that unlike transparent bridging
this is not catastrophic to the network if there
are loops. The value 'auto-span(1)' can only be
returned by a bridge that both implements the
Spanning Tree Protocol and has use of the protocol
enabled on this port. The behavior of the port for
Spanning Tree Explorer frames is determined by the
state of rxr1dStpPortState. If the port is in the
'forwarding' state, the frame will be accepted or
propagated. Otherwise it will be silently
discarded.rw Enumeration .1.3.6.1.4.1.2.6.26.1.3.1.1.7 |
rxr1dSrPortSpecInFramesThe number of specifically routed frames that
have been received from this port's segment.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.8 |
rxr1dSrPortSpecOutFramesThe number of specifically routed frames that
this port has transmitted on its segment.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.9 |
rxr1dSrPortApeInFramesThe number of all paths explorer frames that have
been received by this port from its segment.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.10 |
rxr1dSrPortApeOutFramesThe number of all paths explorer frames that have
been transmitted by this port on its segment.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.11 |
rxr1dSrPortSteInFramesThe number of spanning tree explorer frames that
have been received by this port from its segment.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.12 |
rxr1dSrPortSteOutFramesThe number of spanning tree explorer frames that
have been transmitted by this port on its
segment.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.13 |
rxr1dSrPortSegmentMismatchDiscardsThe number of explorer frames that have been
discarded by this port because the routing
descriptor field contained an invalid adjacent
segment value.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.14 |
rxr1dSrPortDuplicateSegmentDiscardsThe number of frames that have been discarded by
this port because the routing descriptor field
contained a duplicate segment identifier.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.15 |
rxr1dSrPortHopCountExceededDiscardsThe number of explorer frames that have been
discarded by this port because the Routing
Information Field has exceeded the maximum route
descriptor length.ro Counter .1.3.6.1.4.1.2.6.26.1.3.1.1.16 |
rxr1dTp OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.1.4 |
rxr1dTpLearnedEntryDiscardsThe total number of Forwarding Database entries,
which have been or would have been learnt, but
have been discarded due to a lack of space to
store them in the Forwarding Database. If this
counter is increasing, it indicates that the
Forwarding Database is regularly becoming full (a
condition which has unpleasant performance effects
on the subnetwork). If this counter has a
significant value but is not presently increasing,
it indicates that the problem has been occurring
but is not persistent.ro Counter .1.3.6.1.4.1.2.6.26.1.4.1 |
rxr1dTpAgingTimeThe timeout period in seconds for aging out
dynamically learned forwarding information.rw INTEGER .1.3.6.1.4.1.2.6.26.1.4.2 |
rxr1dTpFdbTableA table that contains information about unicast
entries for which the bridge has forwarding and/or
filtering information. This information is used
by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF Rxr1dTpFdbEntry .1.3.6.1.4.1.2.6.26.1.4.3 |
rxr1dTpFdbEntryInformation about a specific unicast MAC address
for which the bridge has some forwarding and/or
filtering information. Rxr1dTpFdbEntry .1.3.6.1.4.1.2.6.26.1.4.3.1 |
rxr1dTpFdbAddressA unicast MAC address for which the bridge has
forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2.6.26.1.4.3.1.1 |
rxr1dTpFdbPortEither the value '0', or the port number of the
port on which a frame having a source address
equal to the value of the corresponding instance
of rxr1dTpFdbAddress has been seen. A value of
'0' indicates that the port number has not been
learned but that the bridge does have some
forwarding/filtering information about this
address (e.g. in the rxr1dStaticTable).
Implementors are encouraged to assign the port
value to this object whenever it is learned even
for addresses for which the corresponding value of
rxr1dTpFdbStatus is not learned(3).ro INTEGER .1.3.6.1.4.1.2.6.26.1.4.3.1.2 |
rxr1dTpFdbStatusThe status of this entry. The meanings of the
values are:
other(1) : none of the following. This would
include the case where some other
MIB object (not the corresponding
instance of rxr1dTpFdbPort, nor an
entry in the rxr1dStaticTable) is
being used to determine if and how
frames addressed to the value of
the corresponding instance of
rxr1dTpFdbAddress are being
forwarded.
invalid(2) : this entry is not longer valid
(e.g., it was learned but has since
aged-out), but has not yet been
flushed from the table.
learned(3) : the value of the corresponding
instance of rxr1dTpFdbPort was
learned, and is being used.
self(4) : the value of the corresponding
instance of rxr1dTpFdbAddress
represents one of the bridge's
addresses. The corresponding
instance of rxr1dTpFdbPort
indicates which of the bridge's
ports has this address.
mgmt(5) : the value of the corresponding
instance of rxr1dTpFdbAddress is
also the value of an existing
instance of rxr1dStaticAddress.ro Enumeration .1.3.6.1.4.1.2.6.26.1.4.3.1.3 |
rxr1dTpPortTableA table that contains information about every
port that is associated with this transparent
bridge. SEQUENCE OF Rxr1dTpPortEntry .1.3.6.1.4.1.2.6.26.1.4.4 |
rxr1dTpPortEntryA list of information for each port of a
transparent bridge. Rxr1dTpPortEntry .1.3.6.1.4.1.2.6.26.1.4.4.1 |
rxr1dTpPortThe port number of the port for which this entry
contains Transparent bridging management
information.ro INTEGER .1.3.6.1.4.1.2.6.26.1.4.4.1.1 |
rxr1dTpPortMaxInfoThe maximum size of the INFO (non-MAC) field that
this port will receive or transmit.ro INTEGER .1.3.6.1.4.1.2.6.26.1.4.4.1.2 |
rxr1dTpPortInFramesThe number of frames that have been received by
this port from its segment. Note that a frame
received on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function.ro Counter .1.3.6.1.4.1.2.6.26.1.4.4.1.3 |
rxr1dTpPortOutFramesThe number of frames that have been transmitted
by this port to its segment. Note that a frame
transmitted on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function.ro Counter .1.3.6.1.4.1.2.6.26.1.4.4.1.4 |
rxr1dTpPortInDiscardsCount of valid frames received which were
discarded (i.e., filtered) by the Forwarding
Process.ro Counter .1.3.6.1.4.1.2.6.26.1.4.4.1.5 |
rxr1dStatic OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.1.5 |
rxr1dStaticTableA table containing filtering information
configured into the bridge by (local or network)
management specifying the set of ports to which
frames received from specific ports and containing
specific destination addresses are allowed to be
forwarded. The value of zero in this table as the
port number from which frames with a specific
destination address are received, is used to
specify all ports for which there is no specific
entry in this table for that particular
destination address. Entries are valid for
unicast and for group/broadcast addresses. SEQUENCE OF Rxr1dStaticEntry .1.3.6.1.4.1.2.6.26.1.5.1 |
rxr1dStaticEntryFiltering information configured into the bridge
by (local or network) management specifying the
set of ports to which frames received from a
specific port and containing a specific
destination address are allowed to be forwarded. Rxr1dStaticEntry .1.3.6.1.4.1.2.6.26.1.5.1.1 |
rxr1dStaticAddressThe destination MAC address in a frame to which
this entry's filtering information applies. This
object can take the value of a unicast address, a
group address or the broadcast address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2.6.26.1.5.1.1.1 |
rxr1dStaticReceivePortEither the value '0', or the port number of the
port from which a frame must be received in order
for this entry's filtering information to apply.
A value of zero indicates that this entry applies
on all ports of the bridge for which there is no
other applicable entry.rw INTEGER .1.3.6.1.4.1.2.6.26.1.5.1.1.2 |
rxr1dStaticAllowedToGoToThe set of ports to which frames received from a
specific port and destined for a specific MAC
address, are allowed to be forwarded. Each octet
within the value of this object specifies a set of
eight ports, with the first octet specifying ports
1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
bridge is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'. (Note that the setting of the bit
corresponding to the port from which a frame is
received is irrelevant.)rw OCTET STRING .1.3.6.1.4.1.2.6.26.1.5.1.1.3 |
rxr1dStaticStatusThis object indicates the status of this entry.
other(1) - this entry is currently in use but
the conditions under which it will
remain so are different from each of the
following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset
of the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently
in use and will remain so until it is
aged out.rw Enumeration .1.3.6.1.4.1.2.6.26.1.5.1.1.4 |
rxripxRouter OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2 |
ipx OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.1 |
ipxSystem OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.1.1 |
ipxSysTableThe IPX System table. SEQUENCE OF IPXSysEntry .1.3.6.1.4.1.2.6.26.2.1.1.1 |
ipxSysEntryEach entry corresponds to one instance of IPX running
on the system. IPXSysEntry .1.3.6.1.4.1.2.6.26.2.1.1.1.1 |
ipxSysInstanceThe unique identifier of the instance of IPX to which this
row corresponds. This value may be written only when
creating a new entry in the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.1.1.1.1 |
ipxSysExistStateThe validity of this entry in the IPX system table.
Setting this field to off indicates that this entry may be
deleted from the system table at the IPX implemntation's
discretion.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.1.1.1.2 |
ipxSysIntNetNumExistsIndicates whether this instance of IPX has an internal
network number.ro Enumeration .1.3.6.1.4.1.2.6.26.2.1.1.1.1.3 |
ipxSysIntNetNumThe IPX internal network number of this instance of IPX.
This value is undefined if the value of
ipxSysIntNetNumExists is no.rw NetNumber .1.3.6.1.4.1.2.6.26.2.1.1.1.1.4 |
ipxSysNameThe readable name for this system.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.1.1.1.5 |
ipxSysMaxPathSplitsThe maximum number of paths with equal routing metric
value which this instance of IPX may split
between when forwarding packets.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.1.1.1.6 |
ipxSysMaxHopsThe maximum number of hops a packet may take.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.1.1.1.7 |
ipxSysVersionMajorThe major version of IPX supported.ro INTEGER .1.3.6.1.4.1.2.6.26.2.1.1.1.1.8 |
ipxSysVersionMinorThe minor version of IPX supported.ro INTEGER .1.3.6.1.4.1.2.6.26.2.1.1.1.1.9 |
ipxSysInReceivesThe total number of IPX packets received, including
those received in error.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.10 |
ipxSysInTooManyHopsThe number of IPX packets discarded due to exceeding the
maximum hop count.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.11 |
ipxSysInHdrErrorsThe number of IPX packets discarded due to errors in
their headers, including ant IPX packet with a size less
than the minimum of 30 bytes.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.12 |
ipxSysInUnknownSocketsThe number of IPX packets discarded because the
destination socket was not open.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.13 |
ipxSysInFilteredThe number of incoming IPX packets discarded due to
filtering.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.14 |
ipxSysInCompressDiscardsThe number of incoming IPX packets discarded due to
decompression errors.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.15 |
ipxSysInDiscardsThe number of IPX packets received but discarded due to
processing decision.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.16 |
ipxSysInDeliversThe total number of IPX packets delivered locally,
including packets from local applications.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.17 |
ipxSysNETBIOSPacketsThe total number of NetBIOS packets received.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.18 |
ipxSysForwPacketsThe number of IPX packets forwarded.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.19 |
ipxSysOutRequestsThe number of IPX packets supplied locally for
transmission, not including any packets counted in
ipxForwPackets.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.20 |
ipxSysOutNoRoutesThe number of IPX packets discarded because no route was
found.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.21 |
ipxSysOutFilteredThe number of outgoing IPX packets discarded due to
filtering.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.22 |
ipxSysOutCompressDiscardsThe number of outgoing IPX packets discarded due to
compression errors.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.23 |
ipxSysOutMalformedRequestsThe number of IPX packets supplied locally that contained
errors in their structure.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.24 |
ipxSysOutDiscardsThe number of outgoing IPX packets discarded due to
processing decision.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.25 |
ipxSysOutPacketsThe total number of IPX packets transmitted.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.26 |
ipxSysCircCountThe number of circuits known to this instance of IPX.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.27 |
ipxSysDestCountThe number of currently reachable destinations known to
this instance of IPX.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.28 |
ipxSysServCountThe number of services known to this instance of IPX.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.29 |
ipxSysResourceFailuresThe number of times this instance of IPX has been
unable to obtain needed resources (memory, etc.).ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.30 |
ipxSysConfigSocketsThe configured maximum number of IPX sockets that may be
open at one time.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.31 |
ipxSysMaxOpenSocketsThe maximum number of IPX sockets actually open at one
time on this system.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.32 |
ipxSysOpenSocketFailsThe number of IPX socket open calls which failed.ro Counter .1.3.6.1.4.1.2.6.26.2.1.1.1.1.33 |
ipxCircuit OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.1.2 |
ipxCircTableThe Circuit table. SEQUENCE OF IPXCircEntry .1.3.6.1.4.1.2.6.26.2.1.2.1 |
ipxCircEntryEach entry corresponds to one circuit known to the
system. IPXCircEntry .1.3.6.1.4.1.2.6.26.2.1.2.1.1 |
ipxCircSysInstanceThe unique identifier of the instance of IPX
to which this entry corresponds. This value may be
written only when creating a new entry in the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.2.1.1.1 |
ipxCircIndexThe identifier of this circuit, unique within the
instance of IPX. This value may be written
only when creating a new entry in the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.2.1.1.2 |
ipxCircExistStateThe validity of this circuit entry. A circuit with this
value set to off may be deleted from the table at the
IPX implementation's discretion.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.2.1.1.3 |
ipxCircOperStateThe operational state of the circuit.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.2.1.1.4 |
ipxCircIfIndexThe value of ifIndex for the interface used by this
circuit. This value may be written only when creating
a new entry in the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.2.1.1.5 |
ipxCircNameThe readable name for the circuit.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.2.1.1.6 |
ipxCircInfoAdditional readable information for the circuit. The
content of this field is implementation defined.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.2.1.1.7 |
ipxCircTypeThe type of the circuit.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.2.1.1.8 |
ipxCircLocalMaxPacketSizeThe maximum size (including header), in bytes, that the
system supports locally on this circuit.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.2.1.1.9 |
ipxCircCompressStateThe compression state on this circuit. This value may
be written only when creating a new entry in the table.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.2.1.1.10 |
ipxCircCompressSlotsThe number of compression slots available on this
circuit. This value may be written only when creating a
new entry in the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.2.1.1.11 |
ipxCircCompressedSentThe number of compressed packets sent.ro Counter .1.3.6.1.4.1.2.6.26.2.1.2.1.1.12 |
ipxCircUncompressedSentThe number of packets sent without being compressed
even though compression was turned on for this circuit.ro Counter .1.3.6.1.4.1.2.6.26.2.1.2.1.1.13 |
ipxCircMediaTypeThe media type used on this circuit.ro OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.2.1.1.14 |
ipxCircNetNumberThe IPX network number to which this circuit is bound.ro NetNumber .1.3.6.1.4.1.2.6.26.2.1.2.1.1.15 |
ipxCircStateChangesThe number of times the circuit has changed state.ro Counter .1.3.6.1.4.1.2.6.26.2.1.2.1.1.16 |
ipxCircInitFailsThe number of times that initialization of this
circuit has failed.ro Counter .1.3.6.1.4.1.2.6.26.2.1.2.1.1.17 |
ipxCircDelayThe period of time, in milliseconds, that it takes to
transmit one byte of data, excluding protocol headers,
to a destination on the other end of the circuit, if
the circuit is free of other traffic.ro INTEGER .1.3.6.1.4.1.2.6.26.2.1.2.1.1.18 |
ipxCircThroughputThe amounf of data, in bits per second, that may flow
through the circuit if there is no other traffic.ro INTEGER .1.3.6.1.4.1.2.6.26.2.1.2.1.1.19 |
ipxForwarding OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.1.3 |
ipxDestTableThe Destination table contains information about all
known destinations. SEQUENCE OF IPXDestEntry .1.3.6.1.4.1.2.6.26.2.1.3.1 |
ipxDestEntryEach entry corresponds to one destination. IPXDestEntry .1.3.6.1.4.1.2.6.26.2.1.3.1.1 |
ipxDestSysInstanceThe unique identifier of the instance of IPX
to which this row corresponds. This value may be written
only when creating a new entry with ipxDestProtocol
equal to static.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.3.1.1.1 |
ipxDestNetNumThe IPX network number of the destination. This value
may be written only when creating a new entry with
ipxDestProtocol equal to static.rw NetNumber .1.3.6.1.4.1.2.6.26.2.1.3.1.1.2 |
ipxDestProtocolThe routing protocol from which knowledge of this
destination was obtained. This value may be written only
when creating a new entry with ipxDestProtocol equal
to static.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.3.1.1.3 |
ipxDestCostThe cost to reach this destination. The meaning of the
cost value is dependent on the routing protocol (i. e.
Cost = delay in ticks for RIP, Cost = total path default
cost for NLSP, etc.). This value may be written only
when creating a new entry with ipxDestProtocol equal
to static.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.3.1.1.4 |
ipxDestHopCountThe number of hops necessary to reach the destination.
This value may be written only when creating a new entry
with ipxDestProtocol equal to static.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.3.1.1.5 |
ipxDestNextHopCircIndexThe unique identifier of the circuit used to reach the
next hop. This value may be written only when creating
a new entry with ipxDestProtocol equal to static.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.3.1.1.6 |
ipxDestNextHopNICAddressThe NIC address of the next hop. This value may be
written only when creating a new entry with
ipxDestProtocol equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.3.1.1.7 |
ipxDestNextHopNetNumThe IPX network number of the next hop. This value may
be written only when creating a new entry with
ipxDestProtocol equal to static.rw NetNumber .1.3.6.1.4.1.2.6.26.2.1.3.1.1.8 |
ipxDestTypeIndicates whether the destination is a network or a
router.ro Enumeration .1.3.6.1.4.1.2.6.26.2.1.3.1.1.9 |
ipxServices OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.1.4 |
ipxServTableThe table of services, indexed by name and type. SEQUENCE OF IPXServEntry .1.3.6.1.4.1.2.6.26.2.1.4.1 |
ipxServEntryEach entry corresponds to one service. IPXServEntry .1.3.6.1.4.1.2.6.26.2.1.4.1.1 |
ipxServSysInstanceThe unique identifier of the instance of IPX
to which this entry corresponds. This value may be
written only when creating entries with the value of
ipxServProtocol equal to static.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.4.1.1.1 |
ipxServNameThe service name. This value may be written only when
creating entries with the value of ipxServProtocol
equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.1.1.2 |
ipxServTypeValueThe service type's hexadecimal value. This value may be
written only when creating entries with the value of
ipxServProtocol equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.1.1.3 |
ipxServTypeThe service type. This value may be written only when
creating entries with the value of ipxServProtocol
equal to static.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.4.1.1.4 |
ipxServProtocolThe protocol from which knowledge of this service was
obtained. This value may be written only when the value
of ipxServProtocol is equal to static.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.4.1.1.5 |
ipxServNetNumThe IPX network number portion of the IPX address of the
service. This value may be written only when creating
entries with the value of ipxServProtocol equal to
static.rw NetNumber .1.3.6.1.4.1.2.6.26.2.1.4.1.1.6 |
ipxServNodeThe node portion of the IPX address of the service. This
value may be written only when creating entries with the
value of ipxServProtocol equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.1.1.7 |
ipxServSocketThe socket portion of the IPX address of the service.
This value may be written only when creating entries with
the value of ipxServProtocol equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.1.1.8 |
ipxDestServTableThe table of services, indexed by address, name,
and type. SEQUENCE OF IPXDestServEntry .1.3.6.1.4.1.2.6.26.2.1.4.2 |
ipxDestServEntryEach entry corresponds to one service. IPXDestServEntry .1.3.6.1.4.1.2.6.26.2.1.4.2.1 |
ipxDestServSysInstanceThe unique identifier of the instance of IPX
to which this entry corresponds. This value may be
written only when creating entries with the value of
ipxDestServProtocol equal to static.rw INTEGER .1.3.6.1.4.1.2.6.26.2.1.4.2.1.1 |
ipxDestServNetNumThe IPX network number portion of the IPX address of the
service. This value may be written only when creating
entries with the value of ipxDestServProtocol equal to
static.rw NetNumber .1.3.6.1.4.1.2.6.26.2.1.4.2.1.2 |
ipxDestServNodeThe node portion of the IPX address of the service. This
value may be written only when creating entries with the
value of ipxDestServProtocol equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.2.1.3 |
ipxDestServSocketThe socket portion of the IPX address of the service.
This value may be written only when creating entries with
the value of ipxDestServProtocol equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.2.1.4 |
ipxDestServNameThe service name. This value may be written only when
creating entries with the value of ipxDestServProtocol
equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.2.1.5 |
ipxDestServTypeValueThe service type's hexadecimal value. This value may be
written only when creating entries with the value of
ipxDestServProtocol equal to static.rw OCTET STRING .1.3.6.1.4.1.2.6.26.2.1.4.2.1.6 |
ipxDestServTypeThe service type. This value may be written only when
creating entries with the value of ipxDestServProtocol
equal to static.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.4.2.1.7 |
ipxDestServProtocolThe protocol from which knowledge of this service was
obtained. This value may be written only when the value
of ipxDestServProtocol is equal to static.rw Enumeration .1.3.6.1.4.1.2.6.26.2.1.4.2.1.8 |
ripsap OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.2 |
ripsapSystem OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.2.1 |
ripsapSysTableThe RIP/SAP system table. SEQUENCE OF RIPSAPSysEntry .1.3.6.1.4.1.2.6.26.2.2.1.1 |
ripsapSysEntryEach entry corresponds to one instance of RIP/SAP
running on the system. RIPSAPSysEntry .1.3.6.1.4.1.2.6.26.2.2.1.1.1 |
ripsapSysInstanceThe unique identifier of the instance of RIP/SAP to
which this row corresponds. This value links the
instance of RIP/SAP to an instance of IPX running on the
system (i. e. the value of ripsapSysInstance should be the
same as a value of ipxSysInstance). This value may be
written only when creating a new entry in the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.1.1.1.1 |
ripsapSysRIPStateIndicates the operational state of this instance of RIP.rw Enumeration .1.3.6.1.4.1.2.6.26.2.2.1.1.1.2 |
ripsapSysSAPStateIndicates the operational state of this instance of SAP.rw Enumeration .1.3.6.1.4.1.2.6.26.2.2.1.1.1.3 |
ripsapSysRIPIncorrectPacketsThe number of times that an incorrectly formatted RIP
packet was received.ro Counter .1.3.6.1.4.1.2.6.26.2.2.1.1.1.4 |
ripsapSysSAPIncorrectPacketsThe number of times that an incorrectly formatted SAP
packet was received.ro Counter .1.3.6.1.4.1.2.6.26.2.2.1.1.1.5 |
ripsapCircuit OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.26.2.2.2 |
ripsapCircTableThe Circuit table. SEQUENCE OF RIPSAPCircEntry .1.3.6.1.4.1.2.6.26.2.2.2.1 |
ripsapCircEntryEach entry corresponds to one circuit known to the
system. RIPSAPCircEntry .1.3.6.1.4.1.2.6.26.2.2.2.1.1 |
ripsapCircSysInstanceThe unique identifier of the instance of RIP/SAP and IPX
(via ipxSysInstance) to which this entry corresponds.
This value may be written only when creating a new entry in
the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.1 |
ripsapCircIndexThe identifier of this circuit, unique within the
instance of RIP/SAP. This value corresponds to the circuit
identifier found in ipxCircIndex. This value may be
written only when creating a new entry in the table.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.2 |
ripsapCircRIPStateIndicates whether RIP information may be sent/received
over this circuit.rw Enumeration .1.3.6.1.4.1.2.6.26.2.2.2.1.1.3 |
ripsapCircRIPPaceThe maximum pace, in packets per second, at which RIP
packets may be sent on this circuit.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.4 |
ripsapCircRIPUpdateThe RIP periodic update interval, in seconds.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.5 |
ripsapCircRIPAgeMultiplierThe holding multiplier for information received in RIP
periodic updates.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.6 |
ripsapCircRIPPacketSizeThe RIP packet size used on this circuit.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.7 |
ripsapCircRIPOutPacketsThe number of RIP packets sent on this circuit.ro Counter .1.3.6.1.4.1.2.6.26.2.2.2.1.1.8 |
ripsapCircRIPInPacketsThe number of RIP packets received on this circuit.ro Counter .1.3.6.1.4.1.2.6.26.2.2.2.1.1.9 |
ripsapCircSAPStateIndicates whether SAP information may be sent/received
over this circuit.rw Enumeration .1.3.6.1.4.1.2.6.26.2.2.2.1.1.10 |
ripsapCircSAPPaceThe maximum pace, in packets per second, at which SAP
packets may be sent on this circuit.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.11 |
ripsapCircSAPUpdateThe SAP periodic update interval, in seconds.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.12 |
ripsapCircSAPAgeMultiplierThe holding multiplier for information received in SAP
periodic updates.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.13 |
ripsapCircSAPPacketSizeThe SAP packet size used on this circuit.rw INTEGER .1.3.6.1.4.1.2.6.26.2.2.2.1.1.14 |
ripsapCircSAPGetNearestServerReplyIndicates whether to respond to SAP Get Nearest Server
requests received on this circuit.rw Enumeration .1.3.6.1.4.1.2.6.26.2.2.2.1.1.15 |
ripsapCircSAPOutPacketsThe number of SAP packets sent on this circuit.ro Counter .1.3.6.1.4.1.2.6.26.2.2.2.1.1.16 |
ripsapCircSAPInPacketsThe number of SAP packets received on this circuit.ro Counter .1.3.6.1.4.1.2.6.26.2.2.2.1.1.17 |