Home/Catalog/HUAWEI-RSVPTE-MIB

HUAWEI-RSVPTE-MIB

AI MIB Summary

The HUAWEI-RSVPTE-MIB module enables monitoring and management of Resource Reservation Protocol over Traffic Engineering (RSVP-TE) sessions, including path setup, teardown, and reservation states, on Huawei networking devices. It provides visibility into critical RSVP-TE metrics such as active LSP counts, signaling errors, and resource utilization to ensure deterministic traffic engineering performance.

The MIB module to describe the RSVP Protocol
Main OID:
hwRsvpTe.1.3.6.1.4.1.2011.5.25.148
234
Objects
Active
Status
6
Dependencies

Imported Objects

HUAWEI-MIB
IF-MIB
INTEGRATED-SERVICES-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

234 total
Object Name
hwRsvpTeThe MIB module to describe the RSVP Protocol
MODULE-IDENTITY
.1.3.6.1.4.1.2011.5.25.148
hwRsvpTeObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.1
hwRsvpTeSessionTableA table of all sessions seen by a given sys- tem.
SEQUENCE OF HwRsvpTeSessionEntry
.1.3.6.1.4.1.2011.5.25.148.1.1
hwRsvpTeSessionEntryA single session seen by a given system.
HwRsvpTeSessionEntry
.1.3.6.1.4.1.2011.5.25.148.1.1.1
hwRsvpTeSessionNumberThe number of this session. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.1.1.1
hwRsvpTeSessionTypeThe type of session (IP4, IP6, IP6 with flow information, etc).ro
SessionType (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.1.1.2
hwRsvpTeSessionDestAddrThe destination address used by all senders in this session.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.1.1.3
hwRsvpTeSessionDestAddrLengthThe CIDR prefix length of the session address, which is 32 for IP4 host and multicast ad- dresses, and 128 for IP6 addresses.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.1.1.4
hwRsvpTeSessionSendersThe number of distinct senders currently known to be part of this session.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.1.1.5
hwRsvpTeSessionReceiversThe number of reservations being requested of this system for this session.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.1.1.6
hwRsvpTeSessionRequestsThe number of reservation requests this system is sending upstream for this session.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.1.1.7
hwRsvpTeSessionTunnelIdA 16-bit identifier used in the SESSION that remains constant over the life of the tunnel.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.1.1.8
hwRsvpTeSessionTunnelExtIdAn identifier used in the SESSION that remains constant over the life of the tunnel. Normally the identifier is set to all zeros. Ingress nodes that wish to narrow the scope of a SESSION to the ingress-egress pair may place their IPv4 address here as a globally unique identifier.ro
IpAddress
.1.3.6.1.4.1.2011.5.25.148.1.1.1.9
hwRsvpTeSessionLspsNumberThe number of LSPs that belong to this session.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.1.1.10
hwRsvpTeSessionStyleAn enumerable value to identify the treatment of reservations for different senders within the same session: WF 10001b, FF01010b, SE 10010b.ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.1.1.11
hwRsvpTeSenderTableInformation describing the state information displayed by senders in PATH messages.
SEQUENCE OF HwRsvpTeSenderEntry
.1.3.6.1.4.1.2011.5.25.148.1.2
hwRsvpTeSenderEntryInformation describing the state information displayed by a single sender's PATH message.
HwRsvpTeSenderEntry
.1.3.6.1.4.1.2011.5.25.148.1.2.1
hwRsvpTeSenderNumberThe number of this sender. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.1
hwRsvpTeSenderTypeThe type of session (IP4, IP6, IP6 with flow information, etc).ro
SessionType (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.2
hwRsvpTeSenderDestAddrThe destination address used by all senders in this session.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.2.1.3
hwRsvpTeSenderAddrThe source address used by this sender in this session.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.2.1.4
hwRsvpTeSenderDestAddrLengthThe length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.5
hwRsvpTeSenderAddrLengthThe length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.6
hwRsvpTeSenderHopAddrThe address used by the previous RSVP hop (which may be the original sender).ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.2.1.7
hwRsvpTeSenderHopLihThe Logical Interface Handle used by the pre- vious RSVP hop (which may be the original sender).ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.8
hwRsvpTeSenderInterfaceThe ifIndex value of the interface on which this PATH message was most recently received.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.9
hwRsvpTeSenderTSpecRateThe Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeSenderTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed hwRsvpTeSen- derTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.10
hwRsvpTeSenderTSpecPeakRateThe Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.11
hwRsvpTeSenderTSpecBurstThe size of the largest burst expected from the sender at a time.ro
BurstSize UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.12
hwRsvpTeSenderTSpecMinTuThe minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.ro
MessageSize (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.13
hwRsvpTeSenderTSpecMaxTuThe maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.ro
MessageSize (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.14
hwRsvpTeSenderIntervalThe interval between refresh messages as ad- vertised by the previous hop.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.15
hwRsvpTeSenderRsvpHopIf TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.16
hwRsvpTeSenderPolicyThe contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.2.1.17
hwRsvpTeSenderAdspecBreakThe global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in the path. If FALSE, no non-IS hops were detected.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.18
hwRsvpTeSenderAdspecHopCountThe hop count general characterization parame- ter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not presentro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.19
hwRsvpTeSenderAdspecPathBwThe path bandwidth estimate general character- ization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not presentro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.20
hwRsvpTeSenderAdspecMinLatencyThe minimum path latency general characteriza- tion parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not presentro
Integer32 UNITS "microseconds"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.21
hwRsvpTeSenderAdspecMtuThe composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not presentro
Integer32 UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.22
hwRsvpTeSenderAdspecGuaranteedSvcIf TRUE, the ADSPEC contains a Guaranteed Ser- vice fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragment.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.23
hwRsvpTeSenderAdspecGuaranteedBreakIf TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the guaranteed service. If FALSE, and hwRsvpTe- SenderAdspecGuaranteedSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns FALSE or noSuchValue.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.24
hwRsvpTeSenderAdspecGuaranteedCtotIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.25
hwRsvpTeSenderAdspecGuaranteedDtotIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "microseconds"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.26
hwRsvpTeSenderAdspecGuaranteedCsumIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'C' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.27
hwRsvpTeSenderAdspecGuaranteedDsumIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'D' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "microseconds"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.28
hwRsvpTeSenderAdspecGuaranteedHopCountIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.29
hwRsvpTeSenderAdspecGuaranteedPathBwIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.30
hwRsvpTeSenderAdspecGuaranteedMinLatencyIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "microseconds"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.31
hwRsvpTeSenderAdspecGuaranteedMtuIf hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.32
hwRsvpTeSenderAdspecCtrlLoadSvcIf TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load Service frag- ment.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.33
hwRsvpTeSenderAdspecCtrlLoadBreakIf TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the controlled load service. If FALSE, and hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns FALSE or noSuchValue.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.2.1.34
hwRsvpTeSenderAdspecCtrlLoadHopCountIf hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.35
hwRsvpTeSenderAdspecCtrlLoadPathBwIf hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.36
hwRsvpTeSenderAdspecCtrlLoadMinLatencyIf hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "microseconds"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.37
hwRsvpTeSenderAdspecCtrlLoadMtuIf hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue.ro
Integer32 UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.38
hwRsvpTeSenderTtlThe TTL value in the RSVP header that was last received.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.39
hwRsvpTeLspIdA 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.40
hwRsvpTeSenderMsgIdSndFlagIndicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.)ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.41
hwRsvpTeSenderMsgIdSndEpochA value that indicates when the Message_Identi- fier sequence has been reset.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.42
hwRsvpTeSenderMsgIdSndNumberWhen combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the Epoch changes or when the value wraps. A return of 0 indicates the absence of the MESSAGE_ID object to be sent.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.43
hwRsvpTeSenderMsgIdRcvFlagThe message ID flag of the message latest received. It is used to identify whether ACK is desired or not. And it can be extended. (0x01: ACK desired.)ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.44
hwRsvpTeSenderMsgIdRcvEpochThe message ID epoch of the message latest received form the interface.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.45
hwRsvpTeSenderMsgIdRcvNumberThe message ID number of the message latest received form the interface. A return of 0 indicates the absence of the MESSAGE_ID object received.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.46
hwRsvpTeSenderClassTypeIndicates the class-type. A return of zero indicates the absence of the object.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.47
hwRsvpTeSenderLabelRequestCtypeThe type of label request (without label range, with ATM label range, with frame relay label range, etc).ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.2.1.48
hwRsvpTeSenderLabelRequestL3pidAn identifier of the layer 3 protocol using this path. Standard Ethertype values are used.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.49
hwRsvpTeSenderLabelRequestAtmMinVpiThis 12 bit field specifies the lower bound of a block of Virtual Path Identifiers that is supported on the originating switch. If the VPI is less than 12-bits it must be right justified in this field and preceding bits must be set to zero.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.50
hwRsvpTeSenderLabelRequestAtmMinVciThis 16 bit field specifies the lower bound of a block of Virtual Connection Identifiers that is supported on the originating switch. If the VCI is less than 16-bits it must be right justified in this field and preceding bits must be set to zero.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.51
hwRsvpTeSenderLabelRequestAtmMaxVpiThis 12 bit field specifies the upper bound of a block of Virtual Path Identifiers that is supported on the originating switch. If the VPI is less than 12-bits it must be right justified in this field and preceding bits must be set to zero.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.52
hwRsvpTeSenderLabelRequestAtmMaxVciThis 16 bit field specifies the upper bound of a block of Virtual Connection Identifiers that is supported on the originating switch. If the VCI is less than 16-bits it must be right justified in this field and preceding bits must be set to zero.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.53
hwRsvpTeSenderLabelRequestFrMinDlciThis 23-bit field specifies the lower bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch. The DLCI must be right justified in this field and unused bits must be set to 0.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.54
hwRsvpTeSenderLabelRequestFrMaxDlciThis 23-bit field specifies the upper bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch. The DLCI must be right justified in this field and unused bits must be set to 0.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.55
hwRsvpTeSenderSessionAttrTypeThe type of the session_attribute (without resource affinities or with resource affinities).ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.2.1.56
hwRsvpTeSenderSessionAttrSetupPrioThe priority of the session with respect to taking resources, in the range of 0 to 7. The value 0 is the highest priority. The Setup Priority is used in deciding whether this session can preempt another session. The default value is 7.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.57
hwRsvpTeSenderSessionAttrHoldPrioThe priority of the session with respect to holding resources, in the range of 0 to 7. The value 0 is the highest priority. Holding Priority is used in deciding whether this session can be preempted by another session. The default value is 7.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.58
hwRsvpTeSenderSessionAttrFlagA mixed value. (0x01: Local protection desired; 0x02: Label recording desired; 0x04: SE Style desired; 0x08: bandwidth protection desired; 0x10: node protection desired; 0x20: Path re-evaluation request; 0x40: Soft preemption desired)ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.59
hwRsvpTeSenderSessionAttrNameSession name, a null padded string of characters.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.2.1.60
hwRsvpTeSenderSessionAttrExcludeAnyA 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link unacceptable.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.61
hwRsvpTeSenderSessionAttrIncludeAnyA 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.62
hwRsvpTeSenderSessionAttrIncludeAllA 32-bit vector representing a set of attribute filters associated with a tunnel all of which must be present for a link to be acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.63
hwRsvpTeSenderFrrSetupPrioThe priority of the backup path with respect to taking resources, in the range 0 to 7. The value 0 is the highest priority. Setup Priority is used in deciding whether this session can preempt another session. See [RSVP-TE] for the usage on priority. The default value is 7.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.64
hwRsvpTeSenderFrrHoldPrioThe priority of the backup path with respect to holding resources, in the range 0 to 7. The value 0 is the highest priority. Holding Priority is used in deciding whether this session can be preempted by another session. The default value is 7.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.65
hwRsvpTeSenderFrrHopLimitThe maximum number of extra hops the backup path is allowed to take, from current node (a PLR) to an MP, with PLR and MP excluded from the count. For example, hop-limit of 0 means that only direct links between PLR and MP can be considered. The default value is 16.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.66
hwRsvpTeSenderFrrFlagAn enumerable value to indicate the protection schema desired (0x01, One-to-One Backup Desired; 0x02, Facility Backup Desired; 0x03, No Backup Desired).ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.2.1.67
hwRsvpTeSenderFrrBandwidthBandwidth estimate; 32-bit IEEE floating point integer, in bits per second.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.2.1.68
hwRsvpTeSenderFrrExcludeAnyA 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link unacceptable.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.69
hwRsvpTeSenderFrrIncludeAnyA 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.70
hwRsvpTeSenderFrrIncludeAllA 32-bit vector representing a set of attribute filters associated with a backup path, all of which must be present for a link to be acceptable (with respect to this test). A null set (all bits set to zero) automatically passes.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.71
hwRsvpTeSenderFrrInuseFlagAn enumerable value to indicate the fast-reroute state of this sender (normal, PLR in use, MP in use, PLR in use and MP in use, under protection).ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.2.1.72
hwRsvpTeSenderDiffServPscThis 16 bits field indicates a PHB Scheduling Class to be supported by the LSP.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.2.1.73
hwRsvpTeResvTableInformation describing the state information displayed by receivers in RESV messages.
SEQUENCE OF HwRsvpTeResvEntry
.1.3.6.1.4.1.2011.5.25.148.1.3
hwRsvpTeResvEntryInformation describing the state information displayed by a single receiver's RESV message concerning a single sender.
HwRsvpTeResvEntry
.1.3.6.1.4.1.2011.5.25.148.1.3.1
hwRsvpTeResvNumberThe number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.3.1.1
hwRsvpTeResvTypeThe type of session (IP4, IP6, IP6 with flow information, etc).ro
SessionType (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.3.1.2
hwRsvpTeResvDestAddrThe destination address used by all senders in this session.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.3.1.3
hwRsvpTeResvSenderAddrThe source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.3.1.4
hwRsvpTeResvDestAddrLengthThe length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.3.1.5
hwRsvpTeResvSenderAddrLengthThe length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.3.1.6
hwRsvpTeResvHopAddrThe address used by the next RSVP hop (which may be the ultimate receiver).ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.3.1.7
hwRsvpTeResvHopLihThe Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver).ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.3.1.8
hwRsvpTeResvInterfaceThe ifIndex value of the interface on which this RESV message was most recently received.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.3.1.9
hwRsvpTeResvServiceThe QoS Service classification requested by the receiver.ro
QosService (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.3.1.10
hwRsvpTeResvTSpecRateThe Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeResvTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed hwRsvpTeResvTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.3.1.11
hwRsvpTeResvTSpecPeakRateThe Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.3.1.12
hwRsvpTeResvTSpecBurstThe size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option.ro
BurstSize UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.3.1.13
hwRsvpTeResvTSpecMinTuThe minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.ro
MessageSize (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.3.1.14
hwRsvpTeResvTSpecMaxTuThe maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.ro
MessageSize (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.3.1.15
hwRsvpTeResvRSpecRateIf the requested service is guaranteed, as specified by hwRsvpTeResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.3.1.16
hwRsvpTeResvRSpecSlackIf the requested service is guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.ro
Integer32 UNITS "microseconds"
.1.3.6.1.4.1.2011.5.25.148.1.3.1.17
hwRsvpTeResvIntervalThe interval between refresh messages as ad- vertised by the Next Hop.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.3.1.18
hwRsvpTeResvScopeThe contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. If the length is non-zero, this contains a series of IP4 or IP6 addresses.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.3.1.19
hwRsvpTeResvSharedIf TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.3.1.20
hwRsvpTeResvExplicitIf TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.3.1.21
hwRsvpTeResvRsvpHopIf TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.3.1.22
hwRsvpTeResvPolicyThe contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.3.1.23
hwRsvpTeResvTtlThe TTL value in the RSVP header that was last received.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.3.1.24
hwRsvpTeResvConfirmReceiver's address.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.3.1.25
hwRsvpTeResvFwdTableInformation describing the state information displayed upstream in RESV messages.
SEQUENCE OF HwRsvpTeResvFwdEntry
.1.3.6.1.4.1.2011.5.25.148.1.4
hwRsvpTeResvFwdEntryInformation describing the state information displayed upstream in an RESV message concern- ing a single sender.
HwRsvpTeResvFwdEntry
.1.3.6.1.4.1.2011.5.25.148.1.4.1
hwRsvpTeResvFwdNumberThe number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.1
hwRsvpTeResvFwdTypeThe type of session (IP4, IP6, IP6 with flow information, etc).ro
SessionType (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.4.1.2
hwRsvpTeResvFwdDestAddrThe destination address used by all senders in this session.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.4.1.3
hwRsvpTeResvFwdSenderAddrThe source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.4.1.4
hwRsvpTeResvFwdDestAddrLengthThe length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.5
hwRsvpTeResvFwdSenderAddrLengthThe length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.6
hwRsvpTeResvFwdHopAddrThe address of the (previous) RSVP that will receive this message.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.4.1.7
hwRsvpTeResvFwdHopLihThe Logical Interface Handle sent to the (pre- vious) RSVP that will receive this message.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.8
hwRsvpTeResvFwdInterfaceThe ifIndex value of the interface on which this RESV message was most recently sent.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.9
hwRsvpTeResvFwdServiceThe QoS Service classification requested.ro
QosService (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.4.1.10
hwRsvpTeResvFwdTSpecRateThe Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeResvFwdT- SpecPeakRate (if supported by the service model);however, averaged across two or more burst intervals, the rate should not exceed hwRsvpTeResvFwdTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.4.1.11
hwRsvpTeResvFwdTSpecPeakRateThe Peak Bit Rate of the sender's data stream Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue.ro
BitRate UNITS "bits per second"
.1.3.6.1.4.1.2011.5.25.148.1.4.1.12
hwRsvpTeResvFwdTSpecBurstThe size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option.ro
BurstSize UNITS "bytes"
.1.3.6.1.4.1.2011.5.25.148.1.4.1.13
hwRsvpTeResvFwdTSpecMinTuThe minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.ro
MessageSize (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.4.1.14
hwRsvpTeResvFwdTSpecMaxTuThe maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.ro
MessageSize (INTEGRATED-SERVICES-MIB)
.1.3.6.1.4.1.2011.5.25.148.1.4.1.15
hwRsvpTeResvFwdRSpecRateIf the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue.ro
BitRate UNITS "bytes per second"
.1.3.6.1.4.1.2011.5.25.148.1.4.1.16
hwRsvpTeResvFwdRSpecSlackIf the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.ro
Integer32 UNITS "microseconds"
.1.3.6.1.4.1.2011.5.25.148.1.4.1.17
hwRsvpTeResvFwdIntervalThe interval between refresh messages adver- tised to the Previous Hop.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.18
hwRsvpTeResvFwdScopeThe contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.4.1.19
hwRsvpTeResvFwdSharedIf TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.4.1.20
hwRsvpTeResvFwdExplicitIf TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.4.1.21
hwRsvpTeResvFwdRsvpHopIf TRUE, the node believes that the next IP hop is an RSVP hop. If FALSE, the node be- lieves that the next IP hop may not be an RSVP hop.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.4.1.22
hwRsvpTeResvFwdPolicyThe contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.4.1.23
hwRsvpTeResvFwdTtlThe TTL value in the RSVP header that was last received.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.24
hwRsvpTeResvFwdMsgIdFlagIndicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.)ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.25
hwRsvpTeResvFwdMsgIdEpochA value that indicates when the Message_Identi- fier sequence has been reset.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.26
hwRsvpTeResvFwdMsgIdNumberWhen combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the epoch changes or when the value wraps. A return of 0 indicates the absence of the MESSAGE_ID object.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.4.1.27
hwRsvpTeIfTableThe RSVP-specific attributes of the system's interfaces.
SEQUENCE OF HwRsvpTeIfEntry
.1.3.6.1.4.1.2011.5.25.148.1.5
hwRsvpTeIfEntryThe RSVP-specific attributes of the a given interface.
HwRsvpTeIfEntry
.1.3.6.1.4.1.2011.5.25.148.1.5.1
hwRsvpTeIfUdpNbrsThe number of neighbors perceived to be using only the RSVP UDP Encapsulation.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.1
hwRsvpTeIfIpNbrsThe number of neighbors perceived to be using only the RSVP IP Encapsulation.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.2
hwRsvpTeIfNbrsThe number of neighbors currently perceived; this will exceed hwRsvpTeIfIpNbrs + hwRsvpTeIfUdpNbrs by the number of neighbors using both encapsu- lations.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.3
hwRsvpTeIfRefreshBlockadeMultipleThe value of the RSVP value 'Kb', Which is the minimum number of refresh intervals that blockade state will last once entered.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.4
hwRsvpTeIfRefreshMultipleThe value of the RSVP value 'K', which is the number of refresh intervals which must elapse (minimum) before a PATH or RESV message which is not being refreshed will be aged out.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.5
hwRsvpTeIfTtlThe value of SEND_TTL used on this interface for messages this node originates. If set to zero, the node determines the TTL via other means.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.6
hwRsvpTeIfRefreshIntervalThe value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface. The default value is 30000.ro
TimeInterval UNITS "milliseconds"
.1.3.6.1.4.1.2011.5.25.148.1.5.1.7
hwRsvpTeIfRouteDelayThe approximate period from the time a route is changed to the time a resulting message ap- pears on the interface. The default value is 200.ro
TimeInterval UNITS "hundredths of a second"
.1.3.6.1.4.1.2011.5.25.148.1.5.1.8
hwRsvpTeIfEnabledIts value is always TRUE, if RSVP is enabled on this Interface.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.9
hwRsvpTeIfUdpRequiredIf TRUE, manual configuration forces the use of UDP encapsulation on the interface. If FALSE, UDP encapsulation is only used if hwRsvpTeI- fUdpNbrs is not zero.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.10
hwRsvpTeIfStatus'active' on interfaces that are configured for RSVP.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.11
hwRsvpTeIfHelloEnabledIf TRUE, RSVPTE hello is enabled on this Interface. If FALSE, RSVPTE hello is not enabled on this interfacero
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.12
hwRsvpTeIfSrefreshEnabledIf TRUE, srefresh is enabled on this interface. If FALSE, srefresh is not enabled on this interface.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.13
hwRsvpTeIfSrefreshIntervalThe srefresh interval. I.e. time difference between 2 refreshes. The default value is 30000.ro
TimeInterval UNITS "milliseconds"
.1.3.6.1.4.1.2011.5.25.148.1.5.1.14
hwRsvpTeIfRetranIncDeltaDelta governs the speed with which the sender increases the retransmission interval. The ratio of two successive retransmission intervals is (1 + Delta).ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.15
hwRsvpTeIfRetranIntervalThe retransmission interval. The default value is 5000.ro
TimeInterval UNITS "milliseconds"
.1.3.6.1.4.1.2011.5.25.148.1.5.1.16
hwRsvpTeIfAuthEnabledIf TRUE, authentication is enabled on this interface. If FALSE, authentication is not enabled on this interface.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.17
hwRsvpTeIfAuthEncryptedThis states that authentication key is encrypted or not.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.18
hwRsvpTeIfAuthHandshakeHandshaking is enabled authentications.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.5.1.19
hwRsvpTeIfAuthLifeTimeAuthentication life time. The default value is 1800000.ro
TimeInterval UNITS "milliseconds"
.1.3.6.1.4.1.2011.5.25.148.1.5.1.20
hwRsvpTeIfAuthKeyAuthentication key, used for authentication processing. For security purposes, a get on this returns a zero length string.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.5.1.21
hwRsvpTeIfWindowSizeAdministrators can specify a message window corresponding to the worst case reordering behavior. For example, one might specify that packets reordered within a 32 message window would be accepted. If no reordering can occur, the window is set to one. The maximum value is 64. The default value is 1.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.5.1.22
hwRsvpTeNbrTableInformation describing the Neighbors of an RSVP system.
SEQUENCE OF HwRsvpTeNbrEntry
.1.3.6.1.4.1.2011.5.25.148.1.6
hwRsvpTeNbrEntryInformation describing a single RSVP Neigh- bor.
HwRsvpTeNbrEntry
.1.3.6.1.4.1.2011.5.25.148.1.6.1
hwRsvpTeNbrAddressThe IP4 or IP6 Address used by this neighbor. This object may not be changed when the value of the RowStatus object is 'active'.
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.6.1.1
hwRsvpTeNbrProtocolThe encapsulation being used by this neigh- bor.ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.6.1.2
hwRsvpTeNbrStatus'active' for all neighbors. This object may be used to configure neighbors. In the pres- ence of configured neighbors, the implementa- tion may (but is not required to) limit the set of valid neighbors to those configured.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.6.1.3
hwRsvpTeNbrSendersNumberThe number of senders on the neighbor.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.6.1.4
hwRsvpTeNbrReceiversNumberThe number of receivers on the neighbor.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.6.1.5
hwRsvpTeNbrHelloEnabledIf TRUE, hello is enabled on the neighbor.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.6.1.6
hwRsvpTeNbrHelloSrcInstanceSource instance of the neighbor.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.6.1.7
hwRsvpTeNbrHelloDstInstanceDestination instance of the neighbor.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.6.1.8
hwRsvpTeNbrHelloLostCounterThe number of times the hello messages have been sent to the neighbor for which hello ACK has not received yet.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.6.1.9
hwRsvpTeNbrHelloTypeHello type that is being sent to the neighbor. A return of 3[none] indicates that hello is disabled on the nbr.ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.6.1.10
hwRsvpTeNbrGrCapabilityGives neighbor capability to support GR or undergo GR, in case of control plane restart. A mixed value. (0x01: Self GR capability of neighbor; 0x02: GR support capability of neighbor; 0x04: Neighbor capable of receiving RecoveryPath message; 0x08: Neighbor capable of sending RecoveryPath message)ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.6.1.11
hwRsvpTeNbrGrRestartTimeNeighbor nodes GR restart time value.ro
TimeStamp UNITS "milliseconds"
.1.3.6.1.4.1.2011.5.25.148.1.6.1.12
hwRsvpTeNbrGrRecoveryTimeNeighbor nodes GR recovery time value.ro
TimeStamp UNITS "milliseconds"
.1.3.6.1.4.1.2011.5.25.148.1.6.1.13
hwRsvpTeNbrGrStatusNeighbor nodes GR status. (0x01, No GR activity; 0x02, Neighbor router is supporting GR; 0x03, Neighbor router is restarting; 0x04, Restart timer is running; 0x05, Recovery timer is running; 0x06, Neighbor GR end.)ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.6.1.14
hwRsvpTeNbrAuthKeyIdNeighbor's authentication key, used for authentication processing. A return of null string indicates the absence of the item. For security purposes, a get on this returns a zero length string.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.6.1.15
hwRsvpTeNbrReductionEnabledIf TRUE srefresh is enabled on the neighbor, else srefresh is not enabled on the neighbor.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.6.1.16
hwRsvpTeNbrReliabilityEnabledIf TRUE reliability is enabled on the neighbor, else reliability is not enabled on the neighbor.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.6.1.17
hwRsvpTeMessageIdTableInformation describes the MessageIds of an RSVP system.
SEQUENCE OF HwRsvpTeMessageIdEntry
.1.3.6.1.4.1.2011.5.25.148.1.7
hwRsvpTeMessageIdEntryInformation describes the MessageIds of an RSVP system.
HwRsvpTeMessageIdEntry
.1.3.6.1.4.1.2011.5.25.148.1.7.1
hwRsvpTeMessageIdEpochA value that indicates when the Message_Identi- fier sequence has been reset.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.7.1.1
hwRsvpTeMessageIdNumberWhen combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the epoch changes or when the value wraps.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.7.1.2
hwRsvpTeMessageIdFlagA enumerable value to indicate the type of this Message_Identifier. (1: SenderIncoming; 2: SenderOutgoing; 3: Resv; 4: ResvFwd; 5: RtBuff)ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.7.1.3
hwRsvpTeFilterSpecTableInformation describes the FilterSpecs of an RSVP system.
SEQUENCE OF HwRsvpTeFilterSpecEntry
.1.3.6.1.4.1.2011.5.25.148.1.8
hwRsvpTeFilterSpecEntryInformation describes the FilterSpecs of an RSVP system.
HwRsvpTeFilterSpecEntry
.1.3.6.1.4.1.2011.5.25.148.1.8.1
hwRsvpTeFilterSpecNumberThe number of this Filter_Spec. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.8.1.1
hwRsvpTeFilterSpecLspIdA 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.8.1.2
hwRsvpTeFilterSpecIngressLsrIdIP address for a sender node.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.8.1.3
hwRsvpTeFilterSpecLabelThe value of the label arranged by next hop. A return of 4294967295 indicates the absence of the item.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.8.1.4
hwRsvpTeRroTableInformation describes the RRO sub-objects of an RSVP system.
SEQUENCE OF HwRsvpTeRroEntry
.1.3.6.1.4.1.2011.5.25.148.1.9
hwRsvpTeRroEntryInformation describes the RRO sub-objects of an RSVP system.
HwRsvpTeRroEntry
.1.3.6.1.4.1.2011.5.25.148.1.9.1
hwRsvpTeRroNumberThe number of this RRO sub-object. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.9.1.1
hwRsvpTeRroTypeAn enumerable value that indicates the type of this sub-object. (0x01: IPv4 address; 0x02: IPv6 address; 0x03: Label.)ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.9.1.2
hwRsvpTeRroIpAddrIP address for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of null string indicates the absence of the item.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.9.1.3
hwRsvpTeRroIpPrefixLenIP prefix length for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of 0 indicates the absence of the item.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.9.1.4
hwRsvpTeRroLabelThe value of the label if the type is 'Label'. A return of 4294967295 indicates the absence of the item.ro
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.9.1.5
hwRsvpTeRroFlagIf hwRsvpTeRroType is IPv4 or IPv6, it is a mixed value. (0x01: Local protection available; 0x02: Local protection in use; 0x04: bandwidth protection; 0x08: node protection; 0x10: preemption pending; 0x20: node ID.) If hwRsvpTeRroType is Label, 0x01 means global label. A return of zero indicates no bit was set.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.9.1.6
hwRsvpTeEroTableInformation describes the ERO sub-objects of an RSVP system.
SEQUENCE OF HwRsvpTeEroEntry
.1.3.6.1.4.1.2011.5.25.148.1.10
hwRsvpTeEroEntryInformation describes the ERO sub-objects of an RSVP system.
HwRsvpTeEroEntry
.1.3.6.1.4.1.2011.5.25.148.1.10.1
hwRsvpTeEroNumberThe number of this ERO sub-object. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Gauge32
.1.3.6.1.4.1.2011.5.25.148.1.10.1.1
hwRsvpTeEroTypeAn enumerable value that indicates the type of this sub-object. (0x01: IPv4 address; 0x02: IPv6 address.)ro
Enumeration
.1.3.6.1.4.1.2011.5.25.148.1.10.1.2
hwRsvpTeEroIpAddrIP address for this sub-object.ro
OCTET STRING
.1.3.6.1.4.1.2011.5.25.148.1.10.1.3
hwRsvpTeEroIpPrefixLenIP prefix length for this sub-object.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.10.1.4
hwRsvpTeExtendObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.1.11
hwRsvpTeExtendTrap
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.1.12
hwRsvpTeTrapObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.1.12.1
hwRsvpTeNbrIP address of RSVP neighbour.ro
IpAddress
.1.3.6.1.4.1.2011.5.25.148.1.12.1.1
hwRsvpTeIfNbrCurrentCountNumber of existing neighbors of the RSVP interface.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.12.1.2
hwRsvpTeIfNbrThresholdThreshold for the number of neighbors of the RSVP interface.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.12.1.3
hwRsvpTeIfNbrTotalCountMaximum number of allowed neighbors of the RSVP interface.ro
Integer32
.1.3.6.1.4.1.2011.5.25.148.1.12.1.4
hwRsvpTeIfNameThe name of the RSVP interface.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.2011.5.25.148.1.12.1.5
hwRsvpTeTrap
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.1.12.2
hwRsvpTeHelloLostIndicates neighbour of RSVP hello lost.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.1
hwRsvpTeHelloLostRecoveryIndicates neighbour of RSVP hello lost.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.2
hwRsvpTeAuthFailIndicates neighbour of RSVP hello lost.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.3
hwRsvpTeAuthSuccessIndicates neighbour of RSVP hello lost.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.4
hwRsvpTeIfNbrThresholdExceedIndicates that the number of RSVP interface neighbors has exceeded the upper threshold.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.5
hwRsvpTeIfNbrThresholdExceedClearIndicates that the number of RSVP interface neighbors has fallen below the lower threshold.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.6
hwRsvpTeIfNbrTotalCountExceedIndicates that the number of RSVP interface neighbors has reached the maximum number.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.7
hwRsvpTeIfNbrTotalCountExceedClearIndicates that the number of RSVP interface neighbors has fallen below the recovery number.
NOTIFICATION-TYPE
.1.3.6.1.4.1.2011.5.25.148.1.12.2.8
hwRsvpTeConformance
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.2
hwRsvpTeGroups
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.2.1
hwRsvpTeCompliances
OBJECT IDENTIFIER
.1.3.6.1.4.1.2011.5.25.148.2.2
HUAWEI-RSVPTE-MIB - SNMP MIB Reference | MIBs Explorer