HUAWEI-MPLSLDP-MIB
AI MIB Summary
The HUAWEI-MPLSLDP-MIB enables monitoring and management of Multiprotocol Label Switching Label Distribution Protocol (MPLS LDP) session states, neighbor adjacencies, and associated traffic statistics on Huawei network devices. It provides specific managed objects and notification traps to track LDP peer establishment failures, label binding updates, and resource utilization within the MPLS forwarding plane.
This MIB contains private managed object and notification trap definitions for MPLS LDP.
Main OID:
hwMplsLdp.1.3.6.1.4.1.2011.5.25.143
156
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
156 total| Object Name |
|---|
hwMplsLdpThis MIB contains private managed object and notification trap
definitions for MPLS LDP. MODULE-IDENTITY .1.3.6.1.4.1.2011.5.25.143 |
hwMplsLdpInfo OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.143.1 |
hwMplsLdpProcessNameThis object indicates the process name of LDP running on the router. By default, the value is LDP.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.1 |
hwMplsLdpLspFecThis object indicates the destination address of an LSP.
The value is either a destination IP address or a prefix of an IP address.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.2011.5.25.143.1.2 |
hwMplsLdpLspInLabelThis object indicates that labels are pushed into all the packets for direct MPLS forwarding.ro Counter32 .1.3.6.1.4.1.2011.5.25.143.1.3 |
hwMplsLdpLspOutLabelThis object indicates that all the packets swap labels for MPLS forwarding.ro Counter32 .1.3.6.1.4.1.2011.5.25.143.1.4 |
hwMplsLdpLspOutIfIndexThe value of this object identifies the index of the outgoing interface of the LSP.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.5.25.143.1.5 |
hwMplsLdpLspDownReasonThis object indicates the cause that the LSP becomes Down.
Options:
1. routeDelete(1) -indicates that a route has been deleted.
2. lspmNotify(2) -indicates that LSPM notify.
3. canNotRecoveryFromGr(3) -indicates that the recovery from GR was failed.
4. recvReleaseMsg(4) -indicates that the release message was received.
5. recvWithdrawMsg(5) -indicates that the withdraw message was received.
6. upStreamLost(6) -indicates that the upstream route was lost.
7. downStreamLost(7) -indicates that the downstream route was lost.
8. otherReason(8) -indicates that another cause was involved.ro Enumeration .1.3.6.1.4.1.2011.5.25.143.1.6 |
hwMplsLdpSessionTableThis object is used to display the session parameters and session age.
The index of this table is hwMplsLdpSessionPeerLsrId. SEQUENCE OF HwMplsLdpSessionEntry .1.3.6.1.4.1.2011.5.25.143.1.7 |
hwMplsLdpSessionEntryThis object is used to display the session parameters and session age.
The index of this entry is hwMplsLdpSessionPeerLsrId. HwMplsLdpSessionEntry .1.3.6.1.4.1.2011.5.25.143.1.7.1 |
hwMplsLdpSessionPeerLsrIdThis object indicates the LSR ID of the peer in a session. MplsLdpIdentifier (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.143.1.7.1.1 |
hwMplsLdpSessionIfIndexThis object indicates the index of the interface on which the session is established.ro Integer32 .1.3.6.1.4.1.2011.5.25.143.1.7.1.2 |
hwMplsLdpSessionDownReasonThis object indicates the cause that the session becomes Down.
Options:
1. sessionUp(0) -indicates that the session was Up.
2. helloHoldTimerExp(1) -indicates that the Hello hold timer expired.
3. ssnHoldTimerExp(2) -indicates that the session hold timer expired.
4. resetMplsLdp(3) -indicates MPLS LDP was reset.
5. undoMplsLdp(4) -indicates that MPLS LDP was disabled.
6. undoMpls(5) -indicates that MPLS was disabled.
7. undoMplsLdpRemotePeer(6) -indicates that the remote peer was deleted.
8. modifyGRConfig(7) -indicates that GR capability was modified.
9. modifyGRTimer(8) -indicates that the GR timer was modified.
10. modifyKeepaliveTimer(9) -indicates that the keepalive timer was modified.
11. modifyMD5Config(10) -indicates that MD5 was configured.
12. ssnRoleSwitch(11) -indicates that the session role was switched.
13. modifyMTUConfig(12) -indicates that the MTU was modified.
14. modifyTransportAddress(13) -indicates that the transport address was modified.
15. modifyLDPLsrID(14) -indicates that the LDP LSR ID was modified.
16. recvNotification(15) -indicates that the notification message was received.
17. transportAddressNotMatch(16) -indicates that the transport address was not matched.
18. protocolGR(17) -indicates that the protocol GR was in processing.
19. ifStatusChanged(18) -indicates that the interface status was changed.
20. tcpDown(19) -indicates that TCP was Down.
21. otherReason(20) -indicates that another cause was involved.
22. sentNotification(21) -indicates that the notification was sent.
23. canntBuildSessionRelation(22) -indicates that the session relation cannot be built.
24. receiveErrorMessageFromPeer(23) -indicates that error message from peer was received.
25. receiveSocketError(24) -indicates that error pakcet from socket was received.
26. sessionDelete(25) -indicates that the session was deleted.
27. modifyCapabilityAnnouncementConfig(26) -indicates that the capability-announcement was modified.
28. modifyLocalLsrID(27) -indicates that the Local LSR ID was modified.
29. modifyP2MP(28) -indicates that the mLDP P2MP was modified.
30. modifyMP2MP(29) -indicates that the mLDP MP2MP was modified.
31. sessionProtectTimerExp(30) -indicates that the session protection timer expired.ro Enumeration .1.3.6.1.4.1.2011.5.25.143.1.7.1.3 |
hwMplsLdpSessionAgeThis object indicates the duration since the session is set up.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.2011.5.25.143.1.7.1.4 |
hwMplsLdpSessionStateTableThis object is used to display the detailed state parameters of the session.
The index of this table is hwMplsLdpSessionPeerId. SEQUENCE OF HwMplsLdpSessionStateEntry .1.3.6.1.4.1.2011.5.25.143.1.8 |
hwMplsLdpSessionStateEntryThis object is used to display the detailed state parameters of the session.
The index of this entry is hwMplsLdpSessionPeerId. HwMplsLdpSessionStateEntry .1.3.6.1.4.1.2011.5.25.143.1.8.1 |
hwMplsLdpSessionPeerIdThis object indicates the LSR ID of the LDP peer to which the session is connected. MplsLdpIdentifier (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.143.1.8.1.1 |
hwMplsLdpSessionLsrIdThis object indicates the ID of the local LSR.ro MplsLdpIdentifier (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.143.1.8.1.2 |
hwMplsLdpSessionTcpConnectionStateThis object indicates the TCP link status of the session.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.3 |
hwMplsLdpSessionStateThis object indicates the current status of the session.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.4 |
hwMplsLdpSessionRoleThis object indicates the session roles.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.5 |
hwMplsLdpSessionFtFlagThis object indicates whether the FT of the session is enabled.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.6 |
hwMplsLdpSessionMd5FlagThis object indicates whether the MD5 is enabled for the peer.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.7 |
hwMplsLdpSessionReconnectTimerThis object indicates the value of the GR reconnection timer after the negotiation.
Unit: secondsro Unsigned32 .1.3.6.1.4.1.2011.5.25.143.1.8.1.8 |
hwMplsLdpSessionRecoveryTimerThis object indicates the value of the GR recovery timer after the negotiation.
Unit: secondsro Unsigned32 .1.3.6.1.4.1.2011.5.25.143.1.8.1.9 |
hwMplsLdpSessionKeepAliveTimerThis object indicates the value of the KeepAlive timer after the negotiation.
Unit: secondsro Unsigned32 .1.3.6.1.4.1.2011.5.25.143.1.8.1.10 |
hwMplsLdpSessionKeepAliveMsgReceivedThis object indicates the number of the KeepAlive messages that the session obtains.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.143.1.8.1.11 |
hwMplsLdpSessionKeepAliveMsgSentThis object indicates the number of the KeepAlive messages that the session sends.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.143.1.8.1.12 |
hwMplsLdpSessionLabelAdvModeThis object indicates the label distribution mode of the session.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.13 |
hwMplsLdpSessionLocalLabelResourceStatusThis object indicates the status of the local label resources of the session.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.14 |
hwMplsLdpSessionPeerLabelResourceStatusThis object indicates the status of the label resources of the LDP peer.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.8.1.15 |
hwMplsLdpSessionAgeStatusThis object indicates the existence time of the session.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.2011.5.25.143.1.8.1.16 |
hwLdpCapabilityConfigThis object indicates the global configuration or deletion of the LDP capability.
Before enabling LDP capability, ensure that the MPLS capability is enabled globally.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.9 |
hwLdpLsrIdThis object indicates the way to change the LDP LSR ID.
The default LDP LSR ID has the same value as the MPLS LSR ID.
It is recommended not to change the LDP LSR ID unless necessary.rw IpAddress .1.3.6.1.4.1.2011.5.25.143.1.10 |
hwLdpPropagateIpPrefixThis object indicates the configuration or deletion of the transit policy for the LDP.
The object has a valid length ranging from 1 to 169 characters.
The length 0 characters shows that the transit policy is deleted.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.11 |
hwLdpGlobalRemotePwe3This object indicates the configuration or deletion of the policy for the LDP remote session.
When the object is enabled, it is forbidden to send mapping message to the remote peer.
By default, the policy is disabled, which means that there is no limitation to send mapping message to the remote peer.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.12 |
hwLdpMtuSignalingThis object indicates the configuration or deletion of the MTU signaling function.
By default, the MTU signaling function is enabled, and the MTU TLV type in the LDP message is 0x900.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.13 |
hwLdpMtuApplyTlvThis object conflicts with the object hwLdpMtuSignaling.
If the object is enabled, it indicates that the MTU TLV type in the LDP message is 0x601 according to the RFC 3988.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.14 |
hwLdpGrCapabilityConfigThis object indicates the configuration or deletion of the LDP GR capability.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.15 |
hwLdpGrNeighborLivenessTimerThis object indicates the way to configure the value of GR neighbor life timer.
When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid.
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.16 |
hwLdpGrReconnectTimerThis object indicates the way to configure the value of GR reconnect timer.
When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid.
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.17 |
hwLdpGrRecoveryTimerThis object indicates the way to configure the value of GR recovery timer.
When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid.
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.18 |
hwMplsLspTriggerThis object indicates the way to configure the LDP policy for the ingress LSP and egress LSP.
Options:
1. all(1) -indicates that all FECs are triggered for the IGP.
2. none(2) -indicates that no FEC is triggered for the IGP.
3. host(3) -indicates that the host FEC is triggered for the IGP.
4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP.
If the object is set as ipprefix, the value of hwMplsLspTriggerIpPrefix must be set together.
Default: hostrw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.19 |
hwMplsLspTriggerIpPrefixThis object indicates the IP prefix when configuring the LDP policy for the ingress LSP and egress LSP.
The object has a valid length ranging from 1 to 169 characters.
If the object is set with a value, the value of hwMplsLspTrigger must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.20 |
hwMplsLspTriggerBgpRouteThis object indicates the policy of triggering the BGP route to create the LDP LSP.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.21 |
hwMplsLspTriggerBgpRouteIpPrefixThis object indicates the IP prefix when triggering the BGP route to create the LDP LSP.
The object has a valid length ranging from 1 to 169 characters.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.22 |
hwLdpResetThis object indicates the reset of the LDP protocol.
Options:
1. reset(1) -indicates the reset of the LDP protocol.
2. resetall(2) -indicates the reset of all LDP instances.
3. ready(3) -indicates that it is ready to reset LDP. This value cannot be set.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.23 |
hwLdpOutBoundSplitHorizonAllThis object indicates the way to set the flag of global split horizon.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.24 |
hwLdpDeleteGtsmAllThis object indicates the deletion of the global GTSM configurations.
Options:
1. delete(1) -indicates that global GTSM configurations are to be deleted.
2. ready(2) -indicates that it is ready to delete global GTSM configurations.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.25 |
hwMplsFrrLspTriggerThis object indicates the way to configure the LDP policy of global instance for LDP Auto FRR.
Options:
1. all(1) -indicates that all FECs are triggered for the IGP.
2. none(2) -indicates that no FEC is triggered for the IGP.
3. host(3) -indicates that the host FEC is triggered for the IGP.
4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP.
If the object is set as ipprefix, the value of hwMplsFrrLspTriggerIpPrefix must be set together.
Default: hostrw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.26 |
hwMplsFrrLspTriggerIpPrefixThis object indicates the IP prefix when configuring LDP Auto FRR for the public network instance.
The object has a valid length ranging from 1 to 169 characters.
If the object is set with a value, the value of hwMplsFrrLspTrigger must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.27 |
hwLdpBackOffTimerInitThis object indicates the initial value of backoff timer.
Default: 15
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.28 |
hwLdpBackOffTimerMaxThis object indicates the maximum value of backoff timer.
Default: 120
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.29 |
hwLdpLongestMatchThis object indicates that the LDP is enabled with the function of searching for routes according to the longest match rule to establish LSPs.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.30 |
hwLdpRemotePeerAutoDodRequestThe value of this object identifies whether the remote peer is globally enabled with the capability of automatically sending a DoD request.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.37 |
hwLdpCapabilityAnnouncementConfigThe value of this object identifies whether LDP has Capability-Announcement ability.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.38 |
hwLdpVpnTableThis object is used to configure or delete the LDP multi-instance.
The index of this table is hwLdpVpnInstanceId.
Make sure the relevant VPN instance is already created. SEQUENCE OF HwLdpVpnEntry .1.3.6.1.4.1.2011.5.25.143.1.50 |
hwLdpVpnEntryThis object is used to configure or delete the LDP multi-instance.
The index of this entry is hwLdpVpnInstanceId.
Make sure the relevant VPN instance is already created. HwLdpVpnEntry .1.3.6.1.4.1.2011.5.25.143.1.50.1 |
hwLdpVpnInstanceIdThis object indicates the ID of the VPN instance.
You can find the correct VPN instance ID based on hwL3vpnVrfIndex of hwL3vpnStatisticsTable. Unsigned32 .1.3.6.1.4.1.2011.5.25.143.1.50.1.1 |
hwLdpVpnLsrIdThis object indicates the way to configure the LDP LSR ID.
If the value of the LDP LSR ID is the same as the value of the MPLS LSR ID, the LDP LSR ID is deleted.
It is recommended not to change the LDP LSR ID unless necessary.rw IpAddress .1.3.6.1.4.1.2011.5.25.143.1.50.1.11 |
hwLdpVpnSplitHorizonAllThis object indicates the way to set the flag of split horizon for all LDP VPN peers.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.50.1.12 |
hwLdpVpnResetThis object indicates the reset of the LDP multi-instance corresponding to the VPN.
Options:
1.reset(1) -indicates that the LDP multi-instance will be reset.
2.ready(2) -indicates that it is ready to reset ldp multi-instance. This value cannot be set.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.50.1.13 |
hwMplsVpnFrrLspTriggerThis object indicates the way to configure the LDP policy of vpn instance for LDP Auto FRR.
Options:
1. all(1) -indicates that all FECs are triggered for the IGP.
2. none(2) -indicates that no FEC is triggered for the IGP.
3. host(3) -indicates that the host FEC is triggered for the IGP.
4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP.
If the object is set as ipprefix, the value of hwMplsVpnFrrLspTriggerIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.50.1.14 |
hwMplsVpnFrrLspTriggerIpPrefixThis object indicates the IP prefix when configuring the LDP policy of vpn instance for LDP Auto FRR.
The object has a valid length ranging from 1 to 169 characters.
If the object is set with a value, the value of hwMplsVpnFrrLspTrigger must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.50.1.15 |
hwLdpVpnGracefulDeleteCapabilityThis object indicates whether the LDP graceful-delete capability is enabled for a VPN instance.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.50.1.16 |
hwLdpVpnGracefulDeleteTimerThe value of this object identifies the value of a graceful-delete timer for a VPN instance.
When the status of hwLdpVpnGracefulDeleteCapability is enabled, the default value returned by the object is valid.
Default: 5
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.50.1.17 |
hwLdpVpnRowStatusThis object indicates whether one entry of hwLdpVpnTable is created or destroyed.
The value of this object can be CreatAndGo or Destroy.
When the value of the object is set as CreatAndGo, and the entry is correctly created,
the status of the object will change into active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.143.1.50.1.51 |
hwLdpRemoteEntityTableThis object is used to configure or delete the LDP remote peer.
The index of this table is hwLdpRemoteName. SEQUENCE OF HwLdpRemoteEntityEntry .1.3.6.1.4.1.2011.5.25.143.1.51 |
hwLdpRemoteEntityEntryThis object is used to configure or delete the LDP remote peer.
The index of this entry is hwLdpRemoteName. HwLdpRemoteEntityEntry .1.3.6.1.4.1.2011.5.25.143.1.51.1 |
hwLdpRemoteNameThis object indicates the name of the LDP remote peer.
Range: 1-32 characters DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.143.1.51.1.1 |
hwLdpRemoteIpThis object indicates the configuration of the remote peer LSR ID.
If being set, the ID cannot be modified.
To modify the ID, delete the original ID and create a new one.
If the ID is set as 0.0.0.0, it indicates that the ID is deleted.rw IpAddress .1.3.6.1.4.1.2011.5.25.143.1.51.1.11 |
hwLdpRemotePwe3This object indicates the configuration or deletion of the policy for the remote LDP session.
When the object is enabled, it is forbidden to send the mapping message to the remote peer.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.51.1.12 |
hwLdpRemoteKeepaliveTimerThis object indicates the value of LDP Keepalive timer.
Default: 45
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.51.1.13 |
hwLdpRemoteHelloTimerThis object indicates the value of LDP Hello hold timer.
Default: 45
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.51.1.14 |
hwLdpRemoteKeepaliveSendTimerThis object indicates the value of LDP Keepalive send timer.
By default, the value of the timer is 0, configuration does not take effect.
Default: 0
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.51.1.15 |
hwLdpRemoteHelloSendTimerThis object indicates the value of LDP Hello send timer.
By default, the value of the timer is 0, configuration does not take effect.
Default: 0
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.51.1.16 |
hwLdpRemoteIgpSyncTimerThis object indicates the value of IGP-Sync timer.
Default: 10
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.51.1.17 |
hwLdpRemoteIpAutoDoDRequestThis object identifies whether the remote peer is enabled with the capability of automatically sending a DoD request.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.51.1.18 |
hwLdpRemoteIpAutoDoDRequestBlockThis object indicates whether the remote ip auto dod request function blocked.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.51.1.19 |
hwLdpRemoteLabelAdvertisementModeThis object indicates the label distribution mode.
Options:
1. dod(1) -indicates that the label distribution mode is dod.
2. du(2) -indicates that the label distribution mode is du.
Default: durw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.51.1.20 |
hwLdpRemoteLocalLsrIdIfIndexThis object indicates the way to specify the interface that the local LDP LSR-ID based on remote entity is assigned to.
Value: 0..2147483647
The default value of the object is the interface that the global LDP LSR ID is assigned to.
If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0.
If set 0, the value of the object will be the default value.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.143.1.51.1.21 |
hwLdpRemoteRowStatusThis object indicates whether one entry of hwLdpRemoteEntityTable is created or destroyed.
The value of this object can be CreatAndGo or Destroy.
When the value of the object is set as CreatAndGo, and the entry is correctly created,
the status of the object will change into active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.143.1.51.1.51 |
hwLdpPeerTableThis object is used to configure the LDP peer.
The index of this table is hwLdpPeerLsrId. SEQUENCE OF HwLdpPeerEntry .1.3.6.1.4.1.2011.5.25.143.1.52 |
hwLdpPeerEntryAn entry of the peer feature table, used to configure and display features,
such as the MD5 password and split horizon policy negotiated with the local peer.
The index of this entry is hwLdpPeerLsrId. HwLdpPeerEntry .1.3.6.1.4.1.2011.5.25.143.1.52.1 |
hwLdpPeerLsrIdThis object indicates the LSR ID of the LDP peer. IpAddress .1.3.6.1.4.1.2011.5.25.143.1.52.1.1 |
hwLdpPeerMd5TypeThis object indicates the Md5 type.
Options:
1. cipher(1) -indicates that the MD5 password is in cipher text mode.
2. plain(2) -indicates that the MD5 password is in plain text mode.
3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.52.1.11 |
hwLdpPeerMd5PasswordThis object indicates the MD5 password of LDP neighbor.
To delete the password, set the password length as zero.
When read, it always returns an Octet string with the length of zero.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.52.1.12 |
hwLdpPeerGtsmHopsThis object indicates the number of GTSM hops.
The valid number of GTSM hops ranges from 1 to 255.
To clear the configuration of GTSM hops, set the number of GTSM hops as 0.rw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.52.1.13 |
hwLdpPeerSplitHorizonThis object indicates the way to set the flag of split horizon for the specified LDP peer.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.52.1.14 |
hwLdpPeerResetThis object indicates the reset of the neighbor services.
Options:
1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect.
2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.52.1.15 |
hwLdpPeerKeychainNameThis object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.52.1.18 |
hwLdpPeerOutBoundPolicyRangeThis object indicates the range of IGP routes for an outbound policy. The default value is clear.
If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyFecIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.52.1.19 |
hwLdpPeerOutBoundPolicyFecIpPrefixThis object indicates the IP prefix list name of IGP routes for an outbound policy.
If the object is set with a value, the value of hwLdpPeerOutBoundPolicyRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.52.1.20 |
hwLdpPeerOutBoundPolicyBgpRangeThis object indicates the range of BGP routes for an outbound policy. The default value is clear.
If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyBgpIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.52.1.21 |
hwLdpPeerOutBoundPolicyBgpIpPrefixThis object indicates the IP prefix list name of BGP routes for the outbound policy.
If the object is set with a value, the value of hwLdpPeerOutBoundPolicyBgpRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.52.1.22 |
hwLdpPeerInBoundPolicyRangeThis object indicates the route range for the inbound policy. The default value is clear.
If the object is set as ipprefix, the value of hwLdpPeerInBoundPolicyFecIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.52.1.23 |
hwLdpPeerInBoundPolicyFecIpPrefixThis object indicates the IP prefix list name for the inbound policy.
If the object is set with a value, the value of hwLdpPeerInBoundPolicyRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.52.1.24 |
hwLdpPeerRowStatusThis object indicates whether one entry of hwLdpPeerTable is created or destroyed.
The value of this object can be CreatAndGo or Destroy.
When the value of the object is set as CreatAndGo, and the entry is correctly created,
the status of the object will change into active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.143.1.52.1.51 |
hwLdpVpnPeerTableThis table is used to create and delete peer configurations in the LDP multi-instance.
The indexs of this table are hwLdpVpnInstanceId, hwLdpVpnPeerLsrId.
Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable. SEQUENCE OF HwLdpVpnPeerEntry .1.3.6.1.4.1.2011.5.25.143.1.53 |
hwLdpVpnPeerEntryAn entry of the VPN peer feature table, used to configure and display features,
such as the MD5 password and split horizon policy negotiated with the local peer on the VPN.
The indexs of this entry are hwLdpVpnInstanceId, hwLdpVpnPeerLsrId.
Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable. HwLdpVpnPeerEntry .1.3.6.1.4.1.2011.5.25.143.1.53.1 |
hwLdpVpnPeerLsrIdThis object indicates the LSR ID of the LDP peer. IpAddress .1.3.6.1.4.1.2011.5.25.143.1.53.1.1 |
hwLdpVpnPeerMd5TypeThis object indicates the Md5 type.
1. cipher(1) -indicates that the MD5 password is in cipher text mode.
2. plain(2) -indicates that the MD5 password is in plain text mode.
3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.53.1.11 |
hwLdpVpnPeerMd5PasswordThis object indicates the MD5 password of VPN LDP neighbor.
To delete the password, set the password length as zero.
When read, it always returns an Octet string with the length of zero.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.53.1.12 |
hwLdpVpnPeerSplitHorizonThis object indicates the way to set the flag of split horizon for the specified LDP peer.
Default: disabledrw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.53.1.13 |
hwLdpVpnPeerResetThis object indicates the reset of the neighbor services.
Options:
1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect.
2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.53.1.14 |
hwLdpVpnPeerKeychainNameThis object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.53.1.17 |
hwLdpVpnPeerRowStatusThis object indicates whether one entry of hwLdpVpnPeerTable is created or destroyed.
The value of this object can be CreatAndGo or Destroy.
When the value of the object is set as CreatAndGo, and the entry is correctly created,
the status of the object will change into active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.143.1.53.1.51 |
hwLdpInterfaceTableThis table is used to configure or delete the LDP capability on the interface.
The index of this table is hwLdpInterfaceIndex. SEQUENCE OF HwLdpInterfaceEntry .1.3.6.1.4.1.2011.5.25.143.1.54 |
hwLdpInterfaceEntryAn entry of the LDP interface table,
used to configure and display the LDP negotiation parameters on the interface enabled with LDP capabilities.
The index of this entry is hwLdpInterfaceIndex. HwLdpInterfaceEntry .1.3.6.1.4.1.2011.5.25.143.1.54.1 |
hwLdpInterfaceIndexThis object indicates the interface index.
You can get the correct interface index based on ifIndex of ifTable. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.5.25.143.1.54.1.1 |
hwLdpStaticFrrProtectTimerThis object indicates the value of static FRR protect timer.
Default: 10
Unit: secondsrwobsolete Integer32 .1.3.6.1.4.1.2011.5.25.143.1.54.1.11 |
hwLdpKeepAliveTimerThis object indicates the value of Keepalive timer.
Default: 45
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.54.1.12 |
hwLdpIgpSyncTimerThis object indicates the value of IGP-Sync timer. By default, the timer is set to 10 seconds.
Default: 10
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.54.1.13 |
hwLdpHelloTimerThis object indicates the value of Hello hold timer. By default, the value of the timer is 15 seconds.
Default: 15
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.54.1.14 |
hwLdpTransportAddressIfIndexThis object indicates the way to specify the interface that the Transport Address is assigned to.
Value: 0..2147483647
The default value of the object for the public interface is the interface that the LDP LSR ID is assigned to.
If the LDP LSR ID is not assigned to any interface, then the value of the object is 0, and 0 cannot be set.
The default value of the object for the private interface is the private interface itself.
Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN.
The interface must be bound with the same VPN instance.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.143.1.54.1.15 |
hwLdpKeepAliveSendTimerThis object indicates the value of LDP Keepalive send timer.
Default: 0
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.54.1.16 |
hwLdpHelloSendTimerThis object indicates the value of LDP Hello send timer.
Default: 0
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.54.1.17 |
hwLdpInterfaceLabelAdvertisementModeThis object indicates the label distribution mode.
Options:
1. dod(1) -indicates that the label distribution mode is dod.
2. du(2) -indicates that the label distribution mode is du.
Default: durw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.54.1.18 |
hwLdpInterfaceLocalLsrIdIfIndexThis object indicates the way to specify the interface that the local LDP LSR-ID based on interface is assigned to.
Value: 0..2147483647
The default value of the object for the public interface is the interface that the global LDP LSR ID is assigned to.
If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0.
If set 0, the value of the object will be the default value.
The default value of the object for the private interface is the interface that the global LDP LSR ID of VPN Instance is assigned to.
Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN.
The interface which the object specified must be bound with the same VPN instance with the interface which is configured.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.2011.5.25.143.1.54.1.19 |
hwLdpInterfaceRowStatusThis object indicates whether one entry of hwLdpInterfaceTable is created or destroyed.
The value of this object can be CreatAndGo or Destroy.
When the value of the object is set as CreatAndGo, and the entry is correctly created,
the status of the object will change into active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.143.1.54.1.51 |
hwLdpPeerGroupTableThis table is used to configure an LDP peer group. SEQUENCE OF HwLdpPeerGroupEntry .1.3.6.1.4.1.2011.5.25.143.1.58 |
hwLdpPeerGroupEntryAn entry of this table. HwLdpPeerGroupEntry .1.3.6.1.4.1.2011.5.25.143.1.58.1 |
hwLdpPeerGroupNameThis object indicates the name of a peer group. OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.58.1.1 |
hwLdpPeerGroupOutBoundRangeThis object indicates the range of IGP routes for an outbound policy.
The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundFecIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.58.1.11 |
hwLdpPeerGroupOutBoundFecIpPrefixThis object indicates the IP prefix list name of IGP routes for an outbound policy.
If the object is set with a value, the value of hwLdpPeerGroupOutBoundRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.58.1.12 |
hwLdpPeerGroupOutBoundBgpRangeThis object indicates the range of BGP routes for an outbound policy. The default value is clear.
If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundBgpIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.58.1.13 |
hwLdpPeerGroupOutBoundBgpIpPrefixThis object indicates the IP prefix list name of BGP routes for an outbound policy.
If the object is set with a value, the value of hwLdpPeerGroupOutBoundBgpRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.58.1.14 |
hwLdpPeerGroupInBoundRangeThis object indicates the route range for an inbound policy. The default value is clear.
If the object is set as ipprefix, the value of hwLdpPeerGroupInBoundIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.58.1.15 |
hwLdpPeerGroupInBoundIpPrefixThis object indicates the IP prefix list name of routes for an inbound policy.
If the object is set with a value, the value of hwLdpPeerGroupInBoundRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.58.1.16 |
hwLdpPeerGroupRowStatusThis object indicates whether one entry of hwLdpPolicyPeerGroupTable is created or destroyed. The value of this object is CreatAndGo or Destroy. When the value of the object is set to CreatAndGo, and the entry is correctly created, the status of the object will change into active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.25.143.1.58.1.51 |
hwLdpOutBoundPolicyPeerAllRangeThis object indicates the range of IGP routes for a global outbound LDP policy. The default value is all.
If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllFecIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.59 |
hwLdpOutBoundPolicyPeerAllFecIpPrefixThis object indicates the IP prefix list name of IGP routes for a global outbound LDP policy. The default value is NULL.
If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.60 |
hwLdpOutBoundPolicyPeerAllBgpRangeThis object indicates the range of BGP routes for a global outbound LDP policy. The default value is all.
If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllBgpIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.61 |
hwLdpOutBoundPolicyPeerAllBgpIpPrefixThis object indicates the IP prefix list name of BGP routes for a global outbound LDP policy. The default value is NULL.
If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllBgpRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.62 |
hwLdpInBoundPolicyPeerAllRangeThis object indicates the range of routes for a global inbound LDP policy. The default value is all.
If the object is set as ipprefix, the value of hwLdpInBoundPolicyPeerAllIpPrefix must be set together.rw Enumeration .1.3.6.1.4.1.2011.5.25.143.1.63 |
hwLdpInBoundPolicyPeerAllIpPrefixThis object indicates the IP prefix list name of routes for a global inbound LDP policy. The default value is NULL.
If the object is set with a value, the value of hwLdpInBoundPolicyPeerAllRange must be set as ipprefix.rw OCTET STRING .1.3.6.1.4.1.2011.5.25.143.1.64 |
hwLdpGracefulDeleteCapabilityThis object indicates whether the LDP graceful-delete capability is enabled.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.2011.5.25.143.1.65 |
hwLdpGracefulDeleteTimerThe value of this object identifies the value of a graceful-delete timer.
When the status of hwLdpGracefulDeleteCapability is enabled, the default value returned by the object is valid.
Default: 5
Unit: secondsrw Integer32 .1.3.6.1.4.1.2011.5.25.143.1.66 |
hwLdpLspDownReasonThe LDP LSP down reason.
Options:
1. other(1) -indicates other reasons.
2. session down(2) -indicates the ldp session went down.
3. route change(3) -indicates the route changed.
4. cannot recovery from GR(4) -indicates LSP cannot recovery from graceful-restart.
5. policy change(5) -indicates the policy changed.ro Enumeration .1.3.6.1.4.1.2011.5.25.143.1.67 |
hwLdpLspDownMplsLsrIdThis object indicates the LSR ID of failed router.ro MplsLsrIdentifier (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.143.1.68 |
hwLdpLspDownOutIfIndexThis object indicates the outgoing interface index of the failed router.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.5.25.143.1.69 |
hwLdpLspDownOutIfMainIpThis object indicates the main ip address of the failed router's outgoing interface.ro IpAddress .1.3.6.1.4.1.2011.5.25.143.1.70 |
hwLdpLspDownOutIfStateThe state of the failed router's outgoing interface.
Options:
1. up(1) -indicates that the state of the outgoing interface is Up.
2. down(2) -indicates that the state of the outgoing interface is Down.ro Enumeration .1.3.6.1.4.1.2011.5.25.143.1.71 |
hwLdpLspDownDownstreamPeerLsrIdThis object indicates the failed router's downstream peer's LSR ID.ro MplsLdpIdentifier (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.143.1.72 |
hwLdpSessionStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.143.1.73 |
hwLdpLocalOperationalSessionNumberThis object indicates the number of local LDP operational sessions.ro Integer32 .1.3.6.1.4.1.2011.5.25.143.1.73.1 |
hwLdpRemoteOperationalSessionNumberThis object indicates the number of remote LDP operational sessions.ro Integer32 .1.3.6.1.4.1.2011.5.25.143.1.73.2 |
hwLdpLocalAndRemoteOperationalSessionNumberThis object indicates the number of local and remote LDP operational sessions.ro Integer32 .1.3.6.1.4.1.2011.5.25.143.1.73.3 |
hwLdpTotalOperationalSessionNumberThis object indicates the total number of LDP operational sessions.ro Integer32 .1.3.6.1.4.1.2011.5.25.143.1.73.4 |
hwMplsLdpTrap OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.143.2 |
hwMplsLdpSessionDownWhen the trap indicating that a session is down is sent, the cause for the down LDP session is displayed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.143.2.1 |
hwMplsLdpLspDownWhen the trap indicating that a session is down is sent, the cause for the down LSP session is displayed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.143.2.2 |
hwMplsLdpHostIngressLspDownClearA trap is sent to clear the down trap of a specified FEC's ingress lsp. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.143.2.3 |
hwMplsLdpHostIngressLspDownA trap is sent when all the ingress lsp of a specified FEC went down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.143.2.4 |
hwMplsLdpConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.143.3 |
hwMplsLdpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.143.3.2 |