HUAWEI-IPPOOL-MIB
AI MIB Summary
The HUAWEI-IPPOOL-MIB module enables the monitoring and management of IP address pool configurations, including active and total address counts, utilization rates, and lease status, specifically on Huawei network devices. It provides granular visibility into DHCP and static IP pool resources to facilitate capacity planning and address allocation troubleshooting.
The MIB contains objects of module IPPOOL.
Main OID:
hwIppool.1.3.6.1.4.1.2011.6.8
348
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
348 total| Object Name |
|---|
hwIppoolThe MIB contains objects of module IPPOOL. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.8 |
hwIPPoolMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.1 |
hwIPPoolTableThe configuration table of IP address pool. SEQUENCE OF HwIPPoolEntry .1.3.6.1.4.1.2011.6.8.1.1 |
hwIPPoolEntryThe configuration list of IP address pool, which is used to configure the relevant attributes of the IP address pool inside the device. HwIPPoolEntry .1.3.6.1.4.1.2011.6.8.1.1.1 |
hwIPPoolIndexExclusive index of address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.1 |
hwIPPoolNameIP address pool name, the service module guarantees the exclusiveness of the name.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.1.1.2 |
hwIPPoolRouterIPAddrGateway IP address.
By default, the mask is 255.255.255.255.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.3 |
hwIPPoolRouterIPMaskGateway mask.
By default, the mask is 255.255.255.255.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.4 |
hwIPPoolPriDNSIPAddrPrimary DNS IP address.
By default, it is 255.255.255.255.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.5 |
hwIPPoolSecDNSIPAddrSecond DNS IP address.
By default, it is 255.255.255.255.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.6 |
hwIPPoolPriNBNSIPAddrPrimary Netbios IP address.
By default, it is 255.255.255.255.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.7 |
hwIPPoolSecNBNSIPAddrSecond Netbios IP address.
By default, it is 255.255.255.255.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.8 |
hwIPPoolIPAddrLeaseIP address lease: 0~(1000*24*60-1)(m) unit: minute. It is allowed not to specify the lease during the adding. The default value is 3*24*60(m).rw Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.9 |
hwIPPoolStatusRow admin status, either Add or Delete.
Supports adding and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.1.1.10 |
hwIPPoolVPNInstanceIP VPN-instance name.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.1.1.11 |
hwIPPoolTypeValue indicates the type of pool, 1-local, 2-relay, 3-server.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.1.1.12 |
hwIPPoolNetworkNetwork ip address of a DHCP Server global pool.
To delete a configured network ip, please set
hwDHCPSGlobalPoolConfigUndoFlag to 1rw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.13 |
hwIPPoolNetworkMaskNet mask of a DHCP Server global pool(network).
The SET operation to this object ought to be with
the SET of hwDHCPSGlobalPoolNetwork together, and
any SET operation alone to this object will be
regarded as an invalid operation.
When a network ip of a DHCP server global pool was
deleted, the net mask would also be deleted
automatically, and no further operation neededrw IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.14 |
hwIPPoolIPTotalNumthe number of total addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.15 |
hwIPPoolIPUsedNumthe number of used addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.16 |
hwIPPoolIPConflictNumthe number of conflict addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.17 |
hwIPPoolIPExcludeNumthe number of exclude addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.18 |
hwIPPoolIPIdleNumthe number of idle addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.19 |
hwIPPoolIPUsedPercentused percent.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.20 |
hwIPPoolDNSIPAddrStringString of DNS server ip addresses for DHCP clients.
Since mostly 8 ip addresses can be configured for a pool
totally, a string is defined to get or configure 8
ip addresses at a timerw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.1.1.21 |
hwIPPoolDNSIPAddrStringUndoA DNS server ip address to be deleted. This object
is only for deleting a given ip address of DNS server.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.1.1.22 |
hwIPPoolNBNSIPAddrStringString of NetBIOS server ip addresses for DHCP
clients. Since mostly 8 ip addresses can be configured for
a pool totally, so a string is defined to get or
configure 8 ip addresses at a timerw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.1.1.23 |
hwIPPoolNBNSIPAddrStringUndoA NetBIOS server ip address to delete. This
object is only for deleting a given ip address of NetBIOS
serverrw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.1.1.24 |
hwIPPoolRouterUnnumberedIfNameunnumbered interface name.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.1.1.25 |
hwIPPoolConflictAutoRecycleIntervalThe flag indicates whether funtion of conflict auto recycle is enabled.rw Integer32 (0 | 30..1440) .1.3.6.1.4.1.2011.6.8.1.1.1.26 |
hwIPPoolLowAddrThe lowest IP address in the pool.ro IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.27 |
hwIPPoolHighAddrThe highest IP address in the pool.ro IpAddress .1.3.6.1.4.1.2011.6.8.1.1.1.28 |
hwIPPoolReqNumThe number of the request packet.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.29 |
hwIPPoolReqSucNumThe number of the effective request packet.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.1.1.30 |
hwIPSectionTableThe configuration table of IP section. SEQUENCE OF HwIPSectionEntry .1.3.6.1.4.1.2011.6.8.1.2 |
hwIPSectionEntryIPSection Entry.
IP section configuration table, used to manage the IP address of user.
There are at most eight address sections to each address pool. Its indexes are hwIPPoolIndex (from the external) and HwIPSectionIndex. HwIPSectionEntry .1.3.6.1.4.1.2011.6.8.1.2.1 |
hwIPSectionIndexIndex of address section.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.2.1.1 |
hwIPSectionDescIP section DESCRIPTION, which can be empty.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.2.1.2 |
hwIPSectionLowAddrStart of address.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.2.1.3 |
hwIPSectionHighAddrEnd of address.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.2.1.4 |
hwIPSectionLengthIP section's length.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.2.1.5 |
hwIPSectionUsedNumThe number of Used addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.2.1.6 |
hwIPSectionConflictThe number of conflict addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.2.1.7 |
hwIPSectionInvalidThe number of invalid addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.2.1.8 |
hwIPSectionAvailableNumThe number of available addresses.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.2.1.9 |
hwIPSectionRowStatusRow admin status, either Add or Delete.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.2.1.10 |
hwIPPoolExtTableExtend table of the local address pool.
When IP addresses are allocated by the built-in DHCP servers, you need to configure the lease and option. SEQUENCE OF HwIPPoolExtEntry .1.3.6.1.4.1.2011.6.8.1.3 |
hwIPPoolExtEntryDESCRIPTION. HwIPPoolExtEntry .1.3.6.1.4.1.2011.6.8.1.3.1 |
hwIPPoolAvailableStatusWhether the address is prohibited.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.1 |
hwIPDhcpOptionId1Option ID.
When IP addresses are allocated by the built-in DHCP sever, the option is a configuration parameter, which needs to be defined and explained by the carrier.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.2 |
hwIPDhcpOption1Value of the option.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.3.1.3 |
hwIPDhcpOptionId2Option ID.
When IP addresses are allocated by the built-in DHCP sever, the option is a configuration parameter, which needs to be defined and explained by the carrier.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.4 |
hwIPDhcpOption2Value of the option.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.3.1.5 |
hwIPDhcpOptionId3Option ID.
When IP addresses are allocated by the built-in DHCP sever, the option is a configuration parameter, which needs to be defined and explained by the carrier.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.6 |
hwIPDhcpOption3Value of the option.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.3.1.7 |
hwIPDhcpOptionId4Option ID.
When IP addresses are allocated by the built-in DHCP sever, the option is a configuration parameter, which needs to be defined and explained by the carrier.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.8 |
hwIPDhcpOption4Value of the option.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.3.1.9 |
hwIPDnsSuffixDNS suffix, a string of 0-50 characters.
If the value is 0, it indicates that the suffix is deleted.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.3.1.10 |
hwIPDhcpSvrIPRsvmode of IP addresses reserving. 1 indicates leasing management, 2 indicates MAC binding, and other values are invalid.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.11 |
hwIPPoolIpAddrRenewalip address renewal: 0~(1000*24*60-1)(m) unit: minute. It is allowed not to specify the renewal during the adding. The default value is 2160(m)rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.12 |
hwIPPoolIpAddrRebindingip address rebinding: 0~(1000*24*60-1)(m) unit: minute. It is allowed not to specify the renewal during the adding. The default value is 3780(m)rw Integer32 .1.3.6.1.4.1.2011.6.8.1.3.1.13 |
hwIPPoolSIPAddr1SIP Server IP addressrw IpAddress .1.3.6.1.4.1.2011.6.8.1.3.1.14 |
hwIPPoolSIPAddr2SIP Server IP addressrw IpAddress .1.3.6.1.4.1.2011.6.8.1.3.1.15 |
hwIPPoolSIPName1The name of SIP server. 0 indicates to delete the SIP server.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.3.1.16 |
hwIPPoolSIPName2The name of SIP server. 0 indicates to delete the SIP server.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.3.1.17 |
hwIPAddressStatusTableAddress status table.
It supports the query and setting of status of the local address pool.
It does not support the query and setting of status of the remote address pool for the following reasons:
1. The status of the remote address pool cannot be set.
2. The remote and local address pools map different status tables, with different indexes.
3. The remote address pool is managed by the remote equipment, rather than the local equipment. The local equipment displays only the approximate status of the remote address pool. SEQUENCE OF HwIPAddressStatusEntry .1.3.6.1.4.1.2011.6.8.1.4 |
hwIPAddressStatusEntryDESCRIPTION. HwIPAddressStatusEntry .1.3.6.1.4.1.2011.6.8.1.4.1 |
hwIPAddressIP address.ro IpAddress .1.3.6.1.4.1.2011.6.8.1.4.1.1 |
hwIPAddressStatusStatus of the address.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.4.1.2 |
hwPoolNameIP address pool name.ro DisplayString .1.3.6.1.4.1.2011.6.8.1.4.1.3 |
hwDhcpSvrGroupTableConfiguration table of the DHCP server group.
To monitor the status of the remote DHCP server, you need to configure the local DHCP server.
You can configure a maximum of 4094 DHCP server groups.
Each server group consists of two DHCP servers. Select the server based on the server status. SEQUENCE OF HwDhcpSvrGroupEntry .1.3.6.1.4.1.2011.6.8.1.5 |
hwDhcpSvrGroupEntryDESCRIPTION. HwDhcpSvrGroupEntry .1.3.6.1.4.1.2011.6.8.1.5.1 |
hwIPPoolDhcpSvrGroupIndexIndex of a DHCP server group.
When you create an address pool, the equipment adds the hwIPPoolDhcpSvrGroupIndex entry by default and sends it to the NMS.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.5.1.1 |
hwIPPoolDhcpSvrGroupNameName of the DHCP server group.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.5.1.2 |
hwIPDhcpSvrPriAddrPrimary IP address of the DHCP server group.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.5.1.3 |
hwIPDhcpSvrScdiAddrSecondary IP address of the DHCP server group.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.5.1.4 |
hwIPDhcpSvrPriStateStatus of the primary DHCP server.ro Enumeration .1.3.6.1.4.1.2011.6.8.1.5.1.5 |
hwIPDhcpScdPriStateStatus of the secondary DHCP server.ro Enumeration .1.3.6.1.4.1.2011.6.8.1.5.1.6 |
hwIPDhcpSvrAutoReleaseWhether the server supports the Release packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.5.1.7 |
hwIPDhcpSvrRefCountNumber of times the server group is referenced.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.5.1.8 |
hwIPDhcpSvrRowStatusDHCP server row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.5.1.9 |
hwIPDhcpSvrPriVpnInstanceVPN instance of the primary DHCP server.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.5.1.10 |
hwIPDhcpSvrScdVpnInstanceVPN instance of the secondary DHCP server.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.5.1.11 |
hwIPDhcpSvrSouceDHCP source interface address.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.5.1.12 |
hwRemotePoolTableConfiguration table of the remote address pool.
The remote address pool must be configured on the local equipment in the following cases:
Users obtain IP addresses through the built-in DHCP client and need to renew the addresses.
The equipment needs to record the IP addresses to be renewed.
The equipment needs to report the routes of the users. SEQUENCE OF HwRemotePoolEntry .1.3.6.1.4.1.2011.6.8.1.6 |
hwRemotePoolEntryDESCRIPTION. HwRemotePoolEntry .1.3.6.1.4.1.2011.6.8.1.6.1 |
hwRemoteIPPoolIndexIndex of an address pool.
When you create an address pool, the equipment adds the hwRemoteIPPoolIndex x entry by default and sends it the NMS.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.6.1.1 |
hwRemoteIPPoolNameName of an address pool.
The service module ensures that the name is unique.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.6.1.2 |
hwRemoteIPPoolRouterIPAddrIP address of the gateway.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.6.1.3 |
hwRemoteIPPoolRouterIPMaskIP address mask.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.6.1.4 |
hwRemoteIPPoolDhcpSvrGroupIDName of the associated DHCP server group.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.6.1.5 |
hwRemoteIPPoolAvailableStatusWhether the address pool is locked, 0: locked, 1: not locked.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.6.1.6 |
hwRemoteIPPoolRowStatusRow status of IP pool.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.6.1.7 |
hwRemoteIPPoolPriDNSIPAddressIP address of the active DNS server.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.6.1.8 |
hwRemoteIPPoolSecDNSIPAddressIP address of the standby DNS server.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.6.1.9 |
hwRemoteIPPoolPriNBNSIPAddressIP address of the active NBNS server.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.6.1.10 |
hwRemoteIPPoolSecNBNSIPAddressIP address of the standby NBNS server.rw IpAddress .1.3.6.1.4.1.2011.6.8.1.6.1.11 |
hwRemoteIPPoolVPNInstanceIP VPN-instance name.rw DisplayString .1.3.6.1.4.1.2011.6.8.1.6.1.12 |
hwRemoteIPPoolDhcpGroupNameDHCP server group name.ro DisplayString .1.3.6.1.4.1.2011.6.8.1.6.1.13 |
hwRemoteIPPoolLeaseManageEnableWhether the address pool lease manage is enable, 0: diable, 1: enable.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.6.1.14 |
hwRemoteIPPoolWeightThe weight of this Remote IP pool.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.6.1.15 |
hwIPPoolStatistic OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.1.7 |
hwIPPoolNumNumber of configured addresses pools.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.7.1 |
hwIPIdleTotalNumNumber of idle addresses on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.7.2 |
hwIPUsedTotalNumNumber of addresses in use on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.7.3 |
hwIPConflictTotalNumNumber of conflicting addresses on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.7.4 |
hwIPExcludeTotalNumNumber of excluded addresses on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.7.5 |
hwIPTotalNumThe total number of IP address.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.7.6 |
hwIPUsedPercentThe percent of used IP address.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.7.7 |
hwDhcpServerTableDHCP server configuration table. SEQUENCE OF HwDhcpServerEntry .1.3.6.1.4.1.2011.6.8.1.8 |
hwDhcpServerEntryDescription. HwDhcpServerEntry .1.3.6.1.4.1.2011.6.8.1.8.1 |
hwDhcpServerIndexThe index of DHCP server.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.8.1.1 |
hwIPPoolDhcpServerIPThe IP address of DHCP server.ro IpAddress .1.3.6.1.4.1.2011.6.8.1.8.1.2 |
hwIPPoolDhcpServerVRFNameThe name of VPN instance for the master DHCP server.ro OCTET STRING .1.3.6.1.4.1.2011.6.8.1.8.1.3 |
hwIPPoolDhcpServerStateThe state of DHCP server.ro Enumeration .1.3.6.1.4.1.2011.6.8.1.8.1.4 |
hwIPPoolDhcpServerSendDisvSpdNumThe send discovering speed number.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.8.1.5 |
hwIPPoolDhcpServerSendDisvSpdSecThe interval of discovery packets sent by DHCP server.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.8.1.6 |
hwIPPoolDhcpServerDeadCountThe threshold of no response packets from DHCP server, when the number count over the threshold, DHCP server is changed from up to down status.
The default value is 1.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.8.1.7 |
hwIPPoolDhcpServerNakCountThe threshold of nak packets from DHCP server, when nak packets count over the threshold, DHCP server is changed from up to down status.
The default value is 10.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.8.1.8 |
hwIPPoolDhcpServerTimeoutThe timeout interval for response packet,the time unit is second and default value is 25 seconds.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.8.1.9 |
hwIPPoolDhcpServerDeadTimeThe interval of DHCP server automatically recover up status, the time unit is minute and default value is 3 minutes.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.8.1.10 |
hwIPPoolOptionTableA table for configuring options to DHCP server pools,
include option code type and value and so on . SEQUENCE OF HwIPPoolOptionEntry .1.3.6.1.4.1.2011.6.8.1.9 |
hwIPPoolOptionEntryDESCRIPTION. HwIPPoolOptionEntry .1.3.6.1.4.1.2011.6.8.1.9.1 |
hwIPDhcpOptionIdOption ID.
When IP addresses are allocated by the built-in DHCP sever, the option is a configuration parameter, which needs to be defined and explained by the carrier.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.9.1.1 |
hwIPDhcpOptionValue of the option.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.9.1.2 |
hwIPDhcpOptionRowStatusThis object is used to configuration new rows in this
table, modify existing rows, and to delete
existing rows.Only three actions are used: active(1),
createAndGo(4), destroy(6).
while configuration new option, you must specify option type
and valuerw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.9.1.3 |
hwIPPoolGroupTableConfiguration table of the address Pool Group.
IP Pool Group support an aggregation of IP Pools. Many Ip Pools of different gateway can be referenced by IP Pool Group.
The max number of IP Pools referenced by an Ip Pool Group is 1024 SEQUENCE OF HwIPPoolGroupEntry .1.3.6.1.4.1.2011.6.8.1.10 |
hwIPPoolGroupEntryThe configuration list of IP address pool group, which is used to configure the relevant attributes of the IP address pool group inside the device. HwIPPoolGroupEntry .1.3.6.1.4.1.2011.6.8.1.10.1 |
hwIPPoolGroupNameName of an IP Pool Group.ro OCTET STRING .1.3.6.1.4.1.2011.6.8.1.10.1.1 |
hwIPPoolGroupVPNInstanceVpn instance of an address Pool Group.
Vpn instance of All IP Pools must accord with the vpn instance of IP Pool Group.
Use string 'rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.10.1.2 |
hwIPPoolGroupIncludeUndoWhether dereference all IP Pools in Pool Group.
Only support dereference all IP Pools in this operation. If dereference Pool one by one is needed, please use IPPoolGroupExtTable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.10.1.3 |
hwIPPoolGroupRowStatusRow status of IP Pool Group.
Support Active, CreateAndGo and Destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.10.1.4 |
hwIPPoolGroupExtTableConfiguration extension table of the address pool group.
The extension table can set the order of an IP pool in IP Pool Group.
The extension table can be used to dereference an IP pool in IP pool Group. SEQUENCE OF HwIPPoolGroupExtEntry .1.3.6.1.4.1.2011.6.8.1.11 |
hwIPPoolGroupExtEntryThe configuration list of IP address pool group extension table. HwIPPoolGroupExtEntry .1.3.6.1.4.1.2011.6.8.1.11.1 |
hwIPPoolGroupExtIncludePoolNameThe IP Pool referenced in IP Pool Group.ro OCTET STRING .1.3.6.1.4.1.2011.6.8.1.11.1.1 |
hwIPPoolGroupExtIncludePoolMoveOrderThe order of IP Pool in IP Pool Group.
Specify the move order to adjust the order of the IP Pool in IP Pool Group.
Only supoort set operation.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.11.1.2 |
hwIPPoolGroupExtRowStatusRow status of IP pool group extension.
Support CreateAndGo and Destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.11.1.3 |
hwIPPoolGroupDisplayTableDisplay table of the address pool group. SEQUENCE OF HwIPPoolGroupDisplayEntry .1.3.6.1.4.1.2011.6.8.1.12 |
hwIPPoolGroupDisplayEntryThe configuration list of IP address pool display group table. HwIPPoolGroupDisplayEntry .1.3.6.1.4.1.2011.6.8.1.12.1 |
hwIPPoolGroupIncludePoolNumThe number of IP Pools referenced in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.1 |
hwIPPoolGroupBoundByDomainNumThe number of IP Pool Groups referenced in domains.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.2 |
hwIPPoolGroupIPTotalNumThe Total number of IP in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.3 |
hwIPPoolGroupIPUsedNumThe Used number of IP in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.4 |
hwIPPoolGroupIPConflictedNumThe Conflicted number of IP in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.5 |
hwIPPoolGroupIPDisableNumThe Disable number of IP in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.6 |
hwIPPoolGroupIPDesignatedNumThe Designated number of IP in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.7 |
hwIPPoolGroupIPFreeNumThe Free number of IP in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.8 |
hwIPPoolGroupIPUsedPercentThe Used Percent of IP in IP Pool Group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.12.1.9 |
hwIPPoolDomainSearchListTableSet the domain search list which is uesed to fill content of DHCP packet option 119.
The option is passed from the DHCP Server to the DHCP Client to specify the domain
search list used when resolving hostnames using DNS. SEQUENCE OF HwIPPoolDomainSearchListEntry .1.3.6.1.4.1.2011.6.8.1.13 |
hwIPPoolDomainSearchListEntryThe configuration list of IP address pool DomainSearchList table. HwIPPoolDomainSearchListEntry .1.3.6.1.4.1.2011.6.8.1.13.1 |
hwIPPoolDomainSearchListThe domain search list which is used to fill content of DHCP packet option 119.ro OCTET STRING .1.3.6.1.4.1.2011.6.8.1.13.1.1 |
hwIPPoolDomainSearchListRowStatusRow status of IP pool DomainSearchList.
Support CreateAndGo and Destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.13.1.2 |
hwIPPoolOptionExtTableA Ext table for configuring options to DHCP server pools,
include option code type and value and so on . SEQUENCE OF HwIPPoolOptionExtEntry .1.3.6.1.4.1.2011.6.8.1.14 |
hwIPPoolOptionExtEntryDESCRIPTION. HwIPPoolOptionExtEntry .1.3.6.1.4.1.2011.6.8.1.14.1 |
hwIPDhcpOptionSubIdSub Option ID.
When IP addresses are allocated by the built-in DHCP sever, the option is a configuration parameter, which needs to be defined and explained by the carrier.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.14.1.1 |
hwIPDhcpOptionSubTypeValue indicates the type of sub-option, 1-ip, 2-string.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.14.1.2 |
hwIPDhcpOptionSubValueValue of the sub-option.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.14.1.3 |
hwIPDhcpOptionSubRowStatusThis object is used to configuration new rows in this
table, modify existing rows, and to delete
existing rows.Only three actions are used: active(1),
createAndGo(4), destroy(6).
while configuration new suboption, you must specify suboption type
and valuerw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.14.1.50 |
hwIPPoolReplyOptionTableA table for configuring options which will be replied to client
in according to specified option value of DHCP client request SEQUENCE OF HwIPPoolReplyOptionEntry .1.3.6.1.4.1.2011.6.8.1.15 |
hwIPPoolReplyOptionEntryDESCRIPTION. HwIPPoolReplyOptionEntry .1.3.6.1.4.1.2011.6.8.1.15.1 |
hwIPDhcpSpecOptionIdOption ID.
Option code from DHCP request of client.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.15.1.1 |
hwIPDhcpSpecOptionOption ID.
Option code from DHCP request of client.ro OCTET STRING .1.3.6.1.4.1.2011.6.8.1.15.1.2 |
hwIPDhcpReplyOptionIdThis object is used to configuration option code which is needed to
reply to client according to specified option value in DHCP request,
Option code, from 2 to 254, include 2 and 254, exclude
3,6,15,44,46,50-54,57-60,82ro Integer32 .1.3.6.1.4.1.2011.6.8.1.15.1.3 |
hwIPDhcpReplyOptionSubIdSub Option ID.
When IP addresses are allocated by the built-in DHCP sever, the option is a configuration parameter,
which needs to be defined and explained by the carrier.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.15.1.4 |
hwIPDhcpReplyOptionSubTypeValue indicates the type of sub-option, 1-ip, 2-string, 3-hex.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.15.1.5 |
hwIPDhcpReplyOptionSubValue of the sub-option.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.15.1.6 |
hwIPDhcpReplyOptionRowStatusThis object is used to configuration new rows in this
table, modify existing rows, and to delete
existing rows.Only three actions are used: active(1),
createAndGo(4), destroy(6).
while configuration new option, you must specify option type
and valuerw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.15.1.50 |
hwIPv6PrefixTableThe configuration table of IPv6 prefix pool. SEQUENCE OF HwIPv6PrefixEntry .1.3.6.1.4.1.2011.6.8.1.16 |
hwIPv6PrefixEntryThe configuration list of IPv6 prefix pool. HwIPv6PrefixEntry .1.3.6.1.4.1.2011.6.8.1.16.1 |
hwIPv6PrefixIndexThe index of IPv6 prefix pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.16.1.1 |
hwIPv6PrefixNameThe name of IPv6 prefix poolrw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.16.1.2 |
hwIPv6PrefixTypeThe type of IPv6 prefix pool.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.16.1.3 |
hwIPv6PrefixThe prefix of IPv6 prefix pool. This node is valid only for local and delegation prefix pool.rw Ipv6AddressPrefix (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.16.1.4 |
hwIPv6PrefixLenThe prefix length of IPv6 prefix pool. Note that 0 is not a configurable value.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.16.1.5 |
hwIPv6PrefixDelegatingLenThe delegating prefix length of IPv6 prefix pool. Note that 0 is not a configurable value. This node is valid only for local and delegation prefix pool.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.16.1.6 |
hwIPv6PrefixAdvPreferredLifetimeThe preferred lifetime(seconds) of IPv6 prefix pool.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.16.1.7 |
hwIPv6PrefixAdvValidLifetimeThe valid lifetime(seconds) of the IPv6 prefix.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.16.1.8 |
hwIPv6PrefixAvailableStatusThe flag indicating whether the IPv6 prefix pool is locked.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.16.1.9 |
hwIPv6VPNInstanceThe vpn instance name of the IPv6 prefix pool.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.16.1.10 |
hwIPv6PrefixReservedFlagThe reserved flag of the IPv6 prefix pool. 0-none reserved, 1-mac reserved, 2-mac plus lease reserved, 3-duid reserved, 4-duid plus lease reserved.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.16.1.11 |
hwIPv6LinkAddressThe link address of the IPv6 remote prefix pool. This node is valid only for remote prefix pool.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.16.1.12 |
hwIPv6SlaacUnsharedFlagThe flag indicates whether prefix pool is used in unshared-mode. The node is valid only for delegation prefix pool.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.16.1.13 |
hwIPv6PrefixRowStatusRow admin status. Support adding, modification and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.16.1.14 |
hwIPPoolPDUnshareOnlyThe flag indicates whether the prefix pool only for DHCPv6 IA_PD. The node is valid only for delegation prefix pool.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.16.1.15 |
hwIPv6PoolTableThe configuration table of IPv6 address pool. SEQUENCE OF HwIPv6PoolEntry .1.3.6.1.4.1.2011.6.8.1.17 |
hwIPv6PoolEntryThe configuration list of IPv6 address pool. HwIPv6PoolEntry .1.3.6.1.4.1.2011.6.8.1.17.1 |
hwIPv6PoolIndexThe index of IPv6 addres pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.17.1.1 |
hwIPv6PoolNameThe name of IPv6 addres pool.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.17.1.2 |
hwIPv6PoolTypeThe type of IPv6 addres pool.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.17.1.3 |
hwIPv6PoolPrefixNameThe prefix pool name of IPv6 addres pool.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.17.1.4 |
hwIPv6PoolDnsIPAddrThe DNS of IPv6 addres pool. The format to set value is : operator+space+primary DNS+space+secondary DNS. operator: 1-Add, 2-Delete.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.17.1.5 |
hwIPv6PoolDnsSearchListThe DNS search list of IPv6 addres pool.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.17.1.6 |
hwIPv6PoolPreferenceThe preference of IPv6 addres pool.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.17.1.7 |
hwIPv6PoolAvailableStatusThe flag indicating whether IPv6 address pool is locked.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.17.1.8 |
hwIPv6PoolRenewPercentThe renew time percent of IPv6 addres pool. When hwIPv6PoolRenewPercent is specified, you need also specify hwIPv6PoolRebindingPercent.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.17.1.9 |
hwIPv6PoolRebindingPercentThe rebinding time percent of IPv6 addres pool. When hwIPv6PoolRebindingPercent is specified, you need also specify hwIPv6PoolRenewPercent.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.17.1.10 |
hwIPv6PoolRapidCommitFlagThe flag indicating whether DHCPv6 rapid-commit is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.17.1.11 |
hwIPv6PoolUnicastOptionThe flag indicating whether DHCPv6 server unicast option is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.17.1.12 |
hwIPv6PoolAFTRNameConfigure the name of Address Family Transition Router.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.17.1.13 |
hwIPv6PoolRowStatusRow admin status. Support adding, modification and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.17.1.14 |
hwIPv6PoolStatusTableThe configuration table of IPv6 address pool's usage. SEQUENCE OF HwIPv6PoolStatusEntry .1.3.6.1.4.1.2011.6.8.1.18 |
hwIPv6PoolStatusEntryThe configuration list of IPv6 address pool's usage. HwIPv6PoolStatusEntry .1.3.6.1.4.1.2011.6.8.1.18.1 |
hwIPv6FreeAddressNumThe free address number of IPv6 addres pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.1 |
hwIPv6UsedAddressNumThe used address number of IPv6 addres pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.2 |
hwIPv6FreePrefixNumThe free prefix number of IPv6 addres pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.3 |
hwIPv6UsedPrefixNumThe used prefix number of IPv6 addres pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.4 |
hwIPv6AddressTotalNumThe total IPv6 address number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.5 |
hwIPv6AddressUsedNumThe used IPv6 address number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.6 |
hwIPv6AddressFreeNumThe free IPv6 address number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.7 |
hwIPv6AddressConflictNumThe conflict IPv6 address number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.8 |
hwIPv6AddressExcludeNumThe excluded IPv6 address number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.9 |
hwIPv6AddressUsedPercentThe percent of used IPv6 addressof IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.10 |
hwIPv6NDRAPrefixTotalNumThe total NDRA prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.11 |
hwIPv6NDRAPrefixUsedNumThe used NDRA prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.12 |
hwIPv6NDRAPrefixFreeNumThe free NDRA prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.13 |
hwIPv6NDRAPrefixConflictNumThe conflict NDRA prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.14 |
hwIPv6NDRAPrefixExcludeNumThe excluded NDRA prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.15 |
hwIPv6NDRAPrefixUsedPercentThe percent of used IPv6 NDRA prefix of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.16 |
hwIPv6PDPrefixTotalNumThe total PD prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.17 |
hwIPv6PDPrefixUsedNumThe used PD prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.18 |
hwIPv6PDPrefixFreeNumThe free PD prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.19 |
hwIPv6PDPrefixConflictNumThe conflict PD prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.20 |
hwIPv6PDPrefixExcludeNumThe excluded PD prefix number of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.21 |
hwIPv6PDPrefixUsedPercentThe percent of used IPv6 PD prefix of IPv6 address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.18.1.22 |
hwIPv6DuidBindPrefixTableThe binding of client DUID and prefix. SEQUENCE OF HwIPv6DuidBindPrefixEntry .1.3.6.1.4.1.2011.6.8.1.19 |
hwIPv6DuidBindPrefixEntryThe binding of client's DUID and prefix. HwIPv6DuidBindPrefixEntry .1.3.6.1.4.1.2011.6.8.1.19.1 |
hwIPv6ClientDuidThe client duid.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.19.1.1 |
hwIPv6BindPrefixThe binding prefix of client.rw Ipv6AddressPrefix (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.19.1.2 |
hwIPv6DuidBindPrefixRowStatusRow admin status. Support adding and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.19.1.3 |
hwDhcpv6SvrGroupTableThe configuration table of the DHCPv6 server group. SEQUENCE OF HwDhcpv6SvrGroupEntry .1.3.6.1.4.1.2011.6.8.1.20 |
hwDhcpv6SvrGroupEntryThe configuration list of DHCPv6 server group. HwDhcpv6SvrGroupEntry .1.3.6.1.4.1.2011.6.8.1.20.1 |
hwDhcpv6SvrGroupIndexThe index of DHCPv6 server group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.20.1.1 |
hwDhcpv6SvrGroupNameThe name of DHCPv6 server group.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.20.1.2 |
hwIPDhcpv6SvrAddr1The primary DNS address.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.20.1.3 |
hwIPDhcpv6SvrAddr2The seconday DNS address.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.20.1.4 |
hwIPDhcpv6PriSvrStateThe status of primary DNS.ro Enumeration .1.3.6.1.4.1.2011.6.8.1.20.1.5 |
hwIPDhcpv6ScdSvrStateThe status of secondary DNS.ro Enumeration .1.3.6.1.4.1.2011.6.8.1.20.1.6 |
hwIPDhcpv6SvrAutoReleaseThe flag indicating whether server will automaticly send DHCPv6 release packet.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.20.1.7 |
hwIPDhcpv6SvrGroupRefCountThe referenced count of DHCPv6 server group.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.20.1.8 |
hwDhcpv6SvrInterface1The outer interface of primary DHCPv6 server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.20.1.9 |
hwDhcpv6SvrInterface2The outer interface of secondary DHCPv6 server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.20.1.10 |
hwDhcpv6SvrAlgorithmThe algorithm of selecting DHCPv6 server.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.20.1.11 |
hwDhcpv6SvrWeight1The weight of primary DHCPv6 server.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.20.1.12 |
hwDhcpv6SvrWeight2The weight of secondary DHCPv6 server.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.20.1.13 |
hwIPDhcpv6Svr1VrfNameThe vpn instance name of primary DHCPv6 server.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.20.1.14 |
hwIPDhcpv6Svr2VrfNameThe vpn instance name of secondary DHCPv6 server.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.20.1.15 |
hwDhcpv6SvrGroupRowStatusRow admin status. Support adding, modification and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.20.1.16 |
hwDhcpv6SvrSourceInterfaceThe interface name whose IP address is the source IP address carried in the packets sent to the server.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.20.1.17 |
hwIPv6RemotePoolTableThe configuration table of IPv6 remote address pool. SEQUENCE OF HwIPv6RemotePoolEntry .1.3.6.1.4.1.2011.6.8.1.21 |
hwIPv6RemotePoolEntryThe configuration list of IPv6 remote address pool. HwIPv6RemotePoolEntry .1.3.6.1.4.1.2011.6.8.1.21.1 |
hwIPv6RemotePoolIndexThe index of remote address pool.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.21.1.1 |
hwIPv6RemotePoolNameThe name of remote address pool.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.21.1.2 |
hwIPv6RemotePoolPrefixNameThe prefix pool name of remote address pool.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.21.1.3 |
hwIPv6RemotePoolDhcpv6SvrGroupNameThe DHCPv6 server group name of remote address pool.rw OCTET STRING .1.3.6.1.4.1.2011.6.8.1.21.1.4 |
hwIPv6RemotePoolAvailableStatusThe flag indicating whether remote address pool is locked.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.21.1.5 |
hwIPv6RemotePoolExportHostRouteFlagThe flag indicating whether to export ipv6 host route.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.21.1.6 |
hwIPv6RemotePoolRowStatusRow admin status. Support adding, modification and deletion.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.21.1.7 |
hwIPv6RemotePoolExportHostRouteIPv6AddressThe flag indicating whether to export host's ipv6 address route .rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.21.1.8 |
hwIPv6RemotePoolExportHostRoutePDPrefixThe flag indicating whether to export host's pd prefix route.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.21.1.9 |
hwIPv6RemotePoolExportHostRouteNDPrefixThe flag indicating whether to export host's nd prefix route.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.6.8.1.21.1.10 |
hwIPv6RemotePoolWeightThe weight of this Remote IPv6 pool.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.21.1.11 |
hwIPv6PoolStatistic OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.1.22 |
hwIpv6PoolNumNumber of configured IPv6 address pools.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.1 |
hwIpv6AddressIdleTotalNumNumber of idle IPv6 addresses on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.2 |
hwIpv6PrefixIdleTotalNumNumber of idle IPv6 prefixes on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.3 |
hwIpv6AddressUsedTotalNumNumber of IPv6 addresses in use on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.4 |
hwIpv6PrefixUsedTotalNumNumber of IPv6 prefixes in use on the equipment.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.5 |
hwAllIPv6AddressTotalNumThe total IPv6 address number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.6 |
hwAllIPv6AddressUsedNumThe used IPv6 address number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.7 |
hwAllIPv6AddressIdleNumThe free IPv6 address number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.8 |
hwAllIPv6ConflictAddressNumThe conflict IPv6 address number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.9 |
hwAllIPv6ExcludeAddressNumThe excluded IPv6 address number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.10 |
hwAllIPv6AddressUsedPercentThe percent of used IPv6 address.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.11 |
hwAllNDRAPrefixTotalNumThe total NDRA prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.12 |
hwAllNDRAPrefixUsedNumThe used NDRA prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.13 |
hwAllNDRAPrefixFreeNumThe free NDRA prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.14 |
hwAllNDRAPrefixConflictNumThe conflict NDRA prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.15 |
hwAllNDRAPrefixExcludeNumThe excluded NDRA prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.16 |
hwAllNDRAPrefixUsedPercentThe percent of used IPv6 NDRA prefix.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.17 |
hwAllPDPrefixTotalNumThe total PD prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.18 |
hwAllPDPrefixUsedNumThe used PD prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.19 |
hwAllPDPrefixFreeNumThe free PD prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.20 |
hwAllPDPrefixConflictNumThe conflict PD prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.21 |
hwAllPDPrefixExcludeNumThe excluded PD prefix number.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.22 |
hwAllPDPrefixUsedPercentThe percent of used IPv6 PD prefix.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.22.23 |
hwDhcpv6ServerTableDHCPv6 server configuration table. SEQUENCE OF HwDhcpv6ServerEntry .1.3.6.1.4.1.2011.6.8.1.23 |
hwDhcpv6ServerEntryThe configuration of DHCPv6 server table. HwDhcpv6ServerEntry .1.3.6.1.4.1.2011.6.8.1.23.1 |
hwDhcpv6SvrIndexThe index of DHCPv6 server.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.23.1.1 |
hwDhcpv6ServerIPThe IPv6 address of DHCPv6 server.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.23.1.2 |
hwDhcpv6ServerVRFNameThe name of VPN instance for the DHCPv6 server.ro OCTET STRING .1.3.6.1.4.1.2011.6.8.1.23.1.3 |
hwDhcpv6ServerIfIndexThe IfIndex of DHCPv6 server.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.23.1.4 |
hwDhcpv6ServerStateThe state of DHCPv6 server.ro Enumeration .1.3.6.1.4.1.2011.6.8.1.23.1.5 |
hwDhcpv6ServerSendSolicitSpeedNumThe speed of sending solicit packet.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.23.1.6 |
hwDhcpv6ServerSendSolicitSpeedSecThe interval of solicit packets sent by DHCPv6 server.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.23.1.7 |
hwIPV6AddressStatusTableA table for configuring the status of ipv6 address which in ipv6 local preifx SEQUENCE OF HwIPV6AddressStatusEntry .1.3.6.1.4.1.2011.6.8.1.24 |
hwIPV6AddressStatusEntryDESCRIPTION. HwIPV6AddressStatusEntry .1.3.6.1.4.1.2011.6.8.1.24.1 |
hwIPv6AddressIpv6Address.ro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.24.1.1 |
hwIPv6AddressStatusIpv6Address status: idle(0) occupied(1) prohibitive(2) conflictive(3).
Status can set idle(0) when prohibitive(2) conflictive(3) reserved(7),set prohibitive(2) when idle(0).rw Enumeration .1.3.6.1.4.1.2011.6.8.1.24.1.2 |
hwIPv6LocalPrefixNameIpv6 Local prefix's name.ro DisplayString .1.3.6.1.4.1.2011.6.8.1.24.1.3 |
hwIPV6PrefixStatusTableA table for configuring the status of ipv6 prefix which in ipv6 delegation preifx SEQUENCE OF HwIPV6PrefixStatusEntry .1.3.6.1.4.1.2011.6.8.1.25 |
hwIPV6PrefixStatusEntryDESCRIPTION. HwIPV6PrefixStatusEntry .1.3.6.1.4.1.2011.6.8.1.25.1 |
hwIpv6PrefixIpv6Prefix.ro Ipv6AddressPrefix (IPV6-TC) .1.3.6.1.4.1.2011.6.8.1.25.1.1 |
hwIpv6PrefixLenIpv6PrefixLength.ro Integer32 .1.3.6.1.4.1.2011.6.8.1.25.1.2 |
hwIPv6PrefixStatusIpv6 Prefix status:idle(0) occupied(1) prohibitive(2) conflictive(3).
Status can set idle(0) when prohibitive(2) conflictive(3) reserved(7),set prohibitive(2) when idle(0).rw Enumeration .1.3.6.1.4.1.2011.6.8.1.25.1.3 |
hwIPv6DelegationPrefixNameIpv6 Delegation prefix's name.ro DisplayString .1.3.6.1.4.1.2011.6.8.1.25.1.4 |
hwIPPoolConstantIndex OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.1.26 |
hwIPPoolConstantIndexEnableEnable IP Pool Constant index function.rw Integer32 .1.3.6.1.4.1.2011.6.8.1.26.1 |
hwIPPoolSetting OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.1.27 |
hwIPPoolAlgorithmThe ipv4 remote pool algorithm.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.27.1 |
hwIPv6PoolAlgorithmThe ipv6 remote pool algorithm.rw Enumeration .1.3.6.1.4.1.2011.6.8.1.27.2 |
hwIPPoolMibTrap OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.2 |
hwIPPoolTrapOid OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.2.1 |
hwUserIPAddressIP address of the user.ro IpAddress .1.3.6.1.4.1.2011.6.8.2.1.1 |
hwDHCPServerAddrIP address of the DHCP server.ro IpAddress .1.3.6.1.4.1.2011.6.8.2.1.2 |
hwDhcpSvrVrfNameDHCP VPN instance name.ro DisplayString .1.3.6.1.4.1.2011.6.8.2.1.3 |
hwIPPoolGroupIndexExclusive index of IP pool group.ro Integer32 .1.3.6.1.4.1.2011.6.8.2.1.4 |
hwDhcpSvrDownReasonDHCP server down reason.ro DisplayString .1.3.6.1.4.1.2011.6.8.2.1.5 |
hwIPPoolDAPNameDAP name.ro DisplayString .1.3.6.1.4.1.2011.6.8.2.1.7 |
hwIPPoolTrapsDefine OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.2.2 |
hwIPPoolTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.2.2.0 |
hwUserIPConflictAlarm1 Notice/Trap name: IP address conflict error.
2 Notice/Trap generation cause: user IP address conflict.
3 Repair suggestions:
Check whether to renew configuring the BAS IP pool.
Check whether the IP address of BAS interface conflicts user IP address. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.1 |
hwUserIPLeaseAlarm1 Notice/Trap name: IP address lease alarm.
2 Notice/Trap generation cause: The user IP lease is over.
3 Repair suggestion:
Check whether to renew configuring BAS IP pool. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.2 |
hwAllocUserIPFailAlarm1 Notice/Trap name: allocate user IP fail alarm.
2 Notice/Trap generation cause: there are no enough IP addresses for users.
3 Repair suggestion:
Check whether there are enough addresses in IP pool of the domain. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.3 |
hwDhcpServerDownDescription: The DHCP server does not respond. This alarm is generated if the network is unstable, the DHCP server is Down, or there is not any available address in the DHCP server when a user applies for an address to the external DHCP server.
Parameter: IP address of the DHCP server, address pool that the user expects (the address pool is identified by the gateway address because there may be multiple address pools on a server), VPN instance name, The reason of that DHCP server is set down status. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.4 |
hwLocalIPPoolDifferWithServerThe configuration of the IP address pool on the DHCP server is not the same as the configuration of the remote address pool on the local equipment.
Solution: Check whether the configuration of the IP address pool on the DHCP server, including the gateway address, mask, and the address range, is the same as the configuration of the remote address pool on the local equipment. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.5 |
hwUsedIPReachThresholdThe number of used IP addresses in the pool exceeds the threshold.
Repair suggestion: Check the configuration of the IP address pool. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.6 |
hwUsedIPReachThresholdResumeThe number of used IP addresses in the pool is under the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.7 |
hwUsedDeleteUnnumberedRouterThe interface is unnumbered by the pool. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.8 |
hwPoolGroupUsedIPReachThresholdThe number of used IP addresses in the IP pool group exceeds the threshold.
Repair suggestion: Check the configuration of the IP address pool group. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.9 |
hwPoolGroupUsedIPReachThresholdResumeThe number of used IP addresses in the IP pool group is under the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.10 |
hwIPPoolConstantIndexFailThe constance index of ip pool recover failure. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.11 |
hwIPv6PrefixConstantIndexFailThe constance index of ipv6 prefix pool recover failure. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.12 |
hwIPv6PoolConstantIndexFailThe constance index of ipv6 pool recover failure. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.13 |
hwUsedIPExhaustThe number of IP addresses in the IP pool is exhausted. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.14 |
hwUsedIPExhaustResumeThe number of IP addresses in the IP pool is under the exhaust. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.15 |
hwPoolGroupUsedIPExhaustThe number of IP addresses in the IP pool group is exhausted. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.16 |
hwPoolGroupUsedIPExhaustResumeThe number of IP addresses in the IP pool group is under the exhaust. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.17 |
hwUsedIPv6AddressAlarmThe number of used IPv6 addresses in the pool exceeds the threshold.
Repair suggestion: Check the configuration of the IP address pool. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.18 |
hwUsedIPv6AddressAlarmResumeThe number of used IPv6 addresses in the IP pool group is under the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.19 |
hwIPv6AddressExhaustAlarmThe IPv6 addresses in the IPv6 pool is exhausted. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.20 |
hwIPv6AddressExhaustAlarmResumeThe IPv6 addresses exhausted alarm cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.21 |
hwIPPoolDAPApplyUnsuccessfulFail to apply for the address segment. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.22 |
hwIPPoolDAPReleaseUnsuccessfulFail to release the address segment. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.23 |
hwIPPoolDAPSubnetFullThe number of address segments dynamically allocated to the device reached the upper limit allowed by the dynamic address pool. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.24 |
hwIPPoolDAPDeviceSubnetFullThe number of address segments dynamically allocated to the device reached the maximum number allowed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.8.2.2.0.25 |
hwIpPoolMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.3 |
hwIpPoolCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.3.1 |
hwIpPoolObjectGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.8.3.2 |