HPN-ICF-RPR-MIB
This MIB manages RPR(Resilient Packet Ring)interfaces by providing an operational table which controls parameters of each RPR interface and reports alarm conditions. A RPR ring is composed of two fiber rings: Outer and Inner.
Main OID:
hpnicfRpr.1.3.6.1.4.1.11.2.14.11.15.2.60
130
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
130 total| Object Name |
|---|
hpnicfRprThis MIB manages RPR(Resilient Packet Ring)interfaces by providing an operational table which controls parameters of each RPR interface and reports alarm conditions. A RPR ring is composed of two fiber rings: Outer and Inner. MODULE-IDENTITY .1.3.6.1.4.1.11.2.14.11.15.2.60 |
hpnicfRprObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1 |
hpnicfRprMaxmumDefine OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.1 |
hpnicfRprMaxmumDefineTableThis table contains the specs of RPR ring. SEQUENCE OF HpnicfRprMaxmumDefineEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1 |
hpnicfRprMaxmumDefineEntryThe entry of RPR Maximum Table. HpnicfRprMaxmumDefineEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1 |
hpnicfRprMaxMumIfIndexThe ifIndex of this RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1.1 |
hpnicfRprMaxStationNumDefineMax station number supported by RPR ring.ro INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1.2 |
hpnicfRprMaxReservedRateDefineMax reserved rate supported by each RPR ringlet. An estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this object reports a value of 'n' then the speed of the interface is somewhere in the range of 'n-500,000' to 'n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero.ro Gauge32 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1.3 |
hpnicfRprTopoImage OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.2 |
hpnicfRprTopoImageXTableThis table contains additional objects for the rprTopoImageTable in IEEE-802DOT17-RPR-MIB. SEQUENCE OF HpnicfRprTopoImageXEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1 |
hpnicfRprTopoImageXEntryEach entry contains information specific to a particular station on the ring. The table has at least one entry for the station itself, this entry indicates zero hops on each ringlet. HpnicfRprTopoImageXEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1 |
hpnicfRprTopoImageXWestEdgeStatusThe current edge status of the west span. If an edge exists,the hpnicfRprTopoImageXWestEdgeStatus is true. Otherwise, the hpnicfRprTopoImageXWestEdgeStatus is false.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1.3 |
hpnicfRprTopoImageXEastEdgeStatusThe current edge status of the east span. If an edge exists, the hpnicfRprTopoImageXEastEdgeStatus is true. Otherwise, the hpnicfRprTopoImageXEastEdgeStatus is false.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1.4 |
hpnicfRprTopoImageXStationNameThe operator assigned station name. The operator can assigned it by hpnicfRprTopoImageXStationName.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1.5 |
hpnicfRprSpanCounters OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3 |
hpnicfRprSrcMacCountTableThe RPR Source Mac Count Table contains the cumulative sum of frames and octects from the particular source station. SEQUENCE OF HpnicfRprSrcMacCountEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1 |
hpnicfRprSrcMacCountEntryAn entry in the RPR Source Mac Count Table. HpnicfRprSrcMacCountEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1 |
hpnicfRprSrcMacCountIfIndexThe ifIndex of this RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.1 |
hpnicfRprSrcMacCountBySrcAddressMAC address of the source station where the frames come from. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.2 |
hpnicfRprSrcMacCountReceivedFramesFrames received from a particular MAC address of source station.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.3 |
hpnicfRprSrcMacCountReceivedOctetsOctets received from a particular MAC address of source station.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.4 |
hpnicfRprDestMacCountTableThe RPR Destination MAC Count Table contains the cumulative sum of frames and octects to the particular destination station. SEQUENCE OF HpnicfRprDestMacCountEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2 |
hpnicfRprDestMacCountEntryAn entry in the RPR MAC Destination Count Table. HpnicfRprDestMacCountEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1 |
hpnicfRprDestMacCountIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.1 |
hpnicfRprDestMacCountByDestAddressMAC address of the destination station where the frames are sent to. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.2 |
hpnicfRprDestMacCountReceivedFramesFrames sent to a particular MAC address of destination station.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.3 |
hpnicfRprDestMacCountReceivedOctetsOctets sent to a particular MAC address of destination station.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.4 |
hpnicfRprPktDropCountTableThe RPR Packet Drop Count Table contains the cumulative sum of packets dropped for congestion. SEQUENCE OF HpnicfRprPktDropCountEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3 |
hpnicfRprPktDropCountEntryAn entry in the RPR Packet Drop Count Table. HpnicfRprPktDropCountEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1 |
hpnicfRprPktDropCntIfIndexThe ifIndex of this RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.1 |
hpnicfRprPktDropCntRingletIDThe RPR Ringlet of the station through which the packets transmit. HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.2 |
hpnicfRprDownFlowClassAPktDropsThe total dropped number of Class A packets which transmit down from the host.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.3 |
hpnicfRprUpFlowClassAPktDropsThe total dropped number of Class A packets which transmit up to the host.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.4 |
hpnicfRprDownFlowClassBPktDropsThe total dropped number of Class B packets which transmit down from the host.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.5 |
hpnicfRprUpFlowClassBPktDropsThe total dropped number of Class B packets which transmit up to the host.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.6 |
hpnicfRprDownFlowClassCPktDropsThe total dropped number of Class C packets which transmit down from the host.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.7 |
hpnicfRprUpFlowClassCPktDropsThe total dropped number of Class C packets which transmit up to the host.ro Counter64 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.8 |
hpnicfRprRS OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4 |
hpnicfRprStaticRSTableThe RPR Static Ring Selection table contains the static ring selection information by the way of configuration. SEQUENCE OF HpnicfRprStaticRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1 |
hpnicfRprStaticRSEntryAn entry in the RPR Static Ring Selection table. HpnicfRprStaticRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1 |
hpnicfRprStaticRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.1 |
hpnicfRprStaticRSMacAddressThe MAC address of the station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.2 |
hpnicfRprStaticRSRingletIDThe identifier of the ring which frames are sent from one station to another. Ringlet0 refers to outer ring, while ringlet1 does inner.rw HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.3 |
hpnicfRprStaticRSTtlThe hops from source station to destination station by the selected ringlet.ro INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.4 |
hpnicfRprStaticRSValidThe flag identify whether the configed ringlet is valid. If it is true, the configed ringlet is valid, otherwise it's invalid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.5 |
hpnicfRprStaticRSRowStatusThe status of this table entry. The status includes createAndGo, active and destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.6 |
hpnicfRprIpv4DynamicRSTableThe RPR Ipv4Dynamic Ring Selection Table that contains the dynamic ring selection information by shortest path. SEQUENCE OF HpnicfRprIpv4DynamicRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2 |
hpnicfRprIpv4DynamicRSEntryAn entry in the RPR Ipv4Dynamic Ring Selection Table. HpnicfRprIpv4DynamicRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1 |
hpnicfRprIpv4DynamicRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.1 |
hpnicfRprIpv4DynamicRSMacAddressThe Ipv4 MAC address of destination station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.2 |
hpnicfRprIpv4DynamicRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.3 |
hpnicfRprIpv4DynamicRSTtlThe hops from source station to destination station by the selected ringlet.ro INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.4 |
hpnicfRprIpv6DynamicRSTableThe RPR Ipv6 Dynamic Ring Selection Table that contains the Ipv6 ring selection information by dynamic ring selection and static ring selection. SEQUENCE OF HpnicfRprIpv6DynamicRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3 |
hpnicfRprIpv6DynamicRSEntryAn entry in the RPR Ipv6 Ring Selection Table. HpnicfRprIpv6DynamicRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1 |
hpnicfRprIpv6DynamicRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.1 |
hpnicfRprIpv6DynamicRSMacAddressThe Ipv6 MAC address of the destination station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.2 |
hpnicfRprIpv6DynamicRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.3 |
hpnicfRprIpv6DynamicRSTtlThe hops from source station to destination station by selected ringlet.ro INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.4 |
hpnicfRprIpv4OverallRSTableThe RPR Ipv4 Overall Ring Selection Table that contains the overall and active ring selection infomation by dynamic ring selection and static ring selection. SEQUENCE OF HpnicfRprIpv4OverallRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4 |
hpnicfRprIpv4OverallRSEntryAn entry in the RPR Overall Ring Selection Table. HpnicfRprIpv4OverallRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1 |
hpnicfRprIpv4OverallRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.1 |
hpnicfRprIpv4OverallRSMacAddressThe MAC address of the destination station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.2 |
hpnicfRprIpv4OverallRSTypeThe ring selection item type indicates static or dynamic.ro Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.3 |
hpnicfRprIpv4OverallRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.4 |
hpnicfRprIpv4OverallRSTtlThe hops from source station to destination station by selected ringlet.ro INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.5 |
hpnicfRprVrrpRSTableThe RPR VRRP Ring Selection Table that contains the ring selection information when the vrrp group is configured. SEQUENCE OF HpnicfRprVrrpRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5 |
hpnicfRprVrrpRSEntryAn entry in the RPR VRRP Ring Selection Table. HpnicfRprVrrpRSEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1 |
hpnicfRprVrrpRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.1 |
hpnicfRprVrrpRSVirtualMacAddressThe virtual MAC address of the staion in VRRP group. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.2 |
hpnicfRprVrrpRSMacAddressThe MAC address of the station that is the master in VRRP group.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.3 |
hpnicfRprVrrpRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.4 |
hpnicfRprVrrpRSTtlThe hops from source station to destination station by selected ringlet.ro INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.5 |
hpnicfRprDefaultRingIDTableThe RPR Default RingID Table specify the default ringID. SEQUENCE OF HpnicfRprDefaultRingIDEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6 |
hpnicfRprDefaultRingIDEntryAn entry in the RPR Default RingID Table. HpnicfRprDefaultRingIDEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1 |
hpnicfRprDefaultRingIDIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1.1 |
hpnicfRprDefaultConfigRingletIDThe default identifier of the ring configured by user.rw HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1.2 |
hpnicfRprDefaultActiveRingIDThe identifier of the default ring which is active currently. The default ring configured by user may be inactive.ro HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1.3 |
hpnicfRprDefect OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.5 |
hpnicfRprDefectReportTableThe RPR Defect Report Table that contains the trap information on the ring. SEQUENCE OF HpnicfRprDefectReportEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1 |
hpnicfRprDefectReportEntryAn entry in the RPR Defect Report Table. HpnicfRprDefectReportEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1.1 |
hpnicfRprDefectIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1.1.1 |
hpnicfRprDefectCurrentStatusIndicates the current status of RPR ring. This attribute is used to notify the management system that alarms generate or clear about some RPR ring.ro Bits .1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1.1.2 |
hpnicfRprPriorityMap OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.6 |
hpnicfRprPriority2ClassMapTableThe Table is for Class Of Service and RPR Service Class Mapping. SEQUENCE OF HpnicfRprPriority2ClassMapEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1 |
hpnicfRprPriority2ClassMapEntryAn entry in the COS to Service Class Map Table. HpnicfRprPriority2ClassMapEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1 |
hpnicfRprPriority2ClassMapIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.1 |
hpnicfRprPriority2ClassMapTypeThe type of Priority,include tag, mpls, ip. Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.2 |
hpnicfRprPriorityValueThe priority of tag,mpls and ip, the value range is 0~7. Enumeration .1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.3 |
hpnicfRprPriority2ClassMapThe RPR service class.rw HpnicfRprServiceClass .1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.4 |
hpnicfRprRateLimitConfig OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.7 |
hpnicfRprRateLimitConfigTableThe RPR Rate Limit Configuration Table that contains the rate limit infomation of RPR serviec class. SEQUENCE OF HpnicfRprRateLimitConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1 |
hpnicfRprRateLimitConfigEntryAn entry in the RPR Rate Limit Configuration Table. HpnicfRprRateLimitConfigEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1 |
hpnicfRprRateLimitConfigIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.1 |
hpnicfRprRateLimitConfigRingletIdThe identifier of the ring of RPR ringlet. HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.2 |
hpnicfRprRateLimitConfigServiceClassThe RPR service class. HpnicfRprServiceClass .1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.3 |
hpnicfRprRateLimitConfigValueThe value of rate-limit that configured for diffrent service class. The unit is permillage.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.4 |
hpnicfRprMacAddrLearn OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8 |
hpnicfRprMacLearnCfgTableThe RPR MAC Address Table. SEQUENCE OF HpnicfRprMacLearnCfgEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1 |
hpnicfRprMacLearnCfgEntryThe entry of RPR MAC Address Table. HpnicfRprMacLearnCfgEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1 |
hpnicfRprMacLearnIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.1 |
hpnicfRprMacLearnRprMacThe MAC address of the RPR station. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.2 |
hpnicfRprMacLearnTypeThe type of MAC address item that the user built. The type includes static and dynamic.rw INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.3 |
hpnicfRprMacLearnDestMacThe destination of MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.4 |
hpnicfRprMacLearnVlanIdThe vlan ID that the MAC address learned from by RPR staion.rw Integer32 .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.5 |
hpnicfRprMacLearnRingletThe identifier of the ring which frames are sent from the source station to the destination station.rw HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.6 |
hpnicfRprMacLearnTtlThe hops from source station to destination station on the selected ringlet.ro INTEGER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.7 |
hpnicfRprMacLearnIsValidThe flag identify whether the configured mac address is valid. If it is true, the configured mac address is valid, otherwise it's invalid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.8 |
hpnicfRprMacLearnRowStatusThe status of this table entry. The status includes createAndGo, active and destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.9 |
hpnicfRprTrapVar OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.9 |
hpnicfRprTrapVarTableThe RPR Defect Report Table that contains varible that used to bind in trap. SEQUENCE OF HpnicfRprTrapVarEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1 |
hpnicfRprTrapVarEntryAn entry in the RPR Trap Var Table. HpnicfRprTrapVarEntry .1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1 |
hpnicfRprTrapIfIndexThe ifIndex of RPR interface. It is only used for trap to bind.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.1 |
hpnicfRprTrapRingletThe span of RPR station. It is only used for trap to bind.ro HpnicfRprRingletID .1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.2 |
hpnicfRprTrapTopoMacAddressThe MAC address of RPR station. It is only used for trap to bind.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.3 |
hpnicfRprTrapIpAddressThe IP address of RPR station. It is only used for trap to bind.ro InetAddress .1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.4 |
hpnicfRprTrap OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10 |
hpnicfRprTopologyOpenRingThe topology openRing trap indicates that the RPR ring is opened. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.1 |
hpnicfRprTopologyCloseRingThe topology openRing trap indicates that the RPR ring is closed. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.2 |
hpnicfRprTopologyInconsistentThe topology inconsistent trap indicates that the topology of RPR is inconsistent. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.3 |
hpnicfRprTopologyInstabilityThe topology instability trap indicates that the topology of RPR is instability. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.4 |
hpnicfRprDuplicateMacAddressThe duplicate MAC address trap indicates that the mac address of the station on the ring is dulplicate. That means there is the same MAC address between two stations on the ring. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.5 |
hpnicfRprDulplicateIPAddressThe dulplicate IP address trap indicates that the IP address of the station on the ring is dulplicate. That means there is the same IP address between two stations on the ring. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.6 |
hpnicfRprIncompleteLRTTThe incomplete LRTT trap indicates that LRTT is not completed. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.7 |
hpnicfRprProtecConfigInconsistentThe protection configuration inconsistent trap indicates that the configuration of protection mode on the ring is inconsistent. That is one station is configured steer mode while the other is configured wrap mode. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.8 |
hpnicfRprJumboConfigInconsistentThe jumbo configuration inconsistent trap indicates that the configuration of jumbo mode on the ring is inconsistent. That is one station supports jumbo frame while the other doesn't support jumbo frame. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.9 |
hpnicfRprExceedMaxReservRateThe exceeded max reserved rate trap indicates that the rate on the ringlet exceeded the max reserved rate. The operator can configure reserved rate for every station, but the sum of all stations' reserved rate of each RPR ringlet can't exceed maximum. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.10 |
hpnicfRprExceedMaxStationNumThe exceeded max station number trap indicates that the number of the stations on the ring exceeded the max station number. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.11 |
hpnicfRprMiscablingThe miscabling trap indicates that the miscabling event occurred. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.12 |
hpnicfRprBackPressureThe back pressure trap indicates that the backpressure is generated on the ringlet. That is the data flow on the ringlet exceeded the range of rate-limit configured. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.13 |
hpnicfRprBackPressureOverThe back pressure over trap indicates that the backpressure is disappeared on the ringlet. NOTIFICATION-TYPE .1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.14 |