HOTWIRE-XDSL-INTERFACE-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for HOTWIRE-XDSL-INTERFACE-MIB.
135
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
135 total| Object Name |
|---|
xdslDevice OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.7745.5.3.1.1 |
xdslLinkUpDownTransitionsThis trap signifies that the sending protocol
entity recognizes that one of the xDSL communication
links is in a fluctuating state. This is a trap of
'minor' class. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.1 |
xdslPortSpeedLowThis trap signifies that the port speed of the
xDSL link has dropped below a threshold value.
This is a trap of 'warning' class TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.2 |
xdslMarginLowThis trap signifies that the margin estimate
is below a customer set threshold value. this is a trap
of 'minor' class. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.3 |
xdslErrorRateHighThis trap signifies that the error rate estimates
is above a customer set threshold value. This is a trap
of 'minor' class. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.4 |
xdslPortFailureThis trap signifies that the processor detected
a bad modem set. This is a trap of 'major' class TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.5 |
xdslTestStartThis trap signifies that a diagnostic test has started on one of the
ports TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.6 |
xdslRtuTypeMismatchThe RTU configured in the DSL card does NOT match with the RTU connected
to the DSL port indicated by the ifIndex. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.7 |
xdslRtuSelfTestFailA self test failure from the RTU connected
to the DSL port indicated by the ifIndex. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.16 |
xdslRtuLastGaspCard received LastGap message from SN followed by a link
down condition one minute later. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.17 |
xdslSNDeviceFailOperating software has detected an internal device failure. The
RTU is still operating. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.18 |
xdslSNSelfTestFailFailure of the RTU's hardware components. This trap is only set if the
hardware failure still allows sending traps. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.19 |
xdslSNFatalResetFatal error device reset TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.20 |
xdslLinkDownAnalysisTrapThis trap signifies that the sending protocol
entity recognizes that the xDSL communication
link is up. LinkDownReason conveys the reason
for link down. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.21 |
xdslRemoteInjectionFailureTrapThis trap signifies that the injection of filters to SN failed
It is of warning class TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.22 |
xdslRemoteInjectionIncompatibleTrapThis trap signifies that the injection of filters is not supported
by the SN. It is of warning class TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.23 |
xdslLossOfNetworkTimingSignalTrapThis trap is generated by an IDSL port card when it detects
that the line supplying timing signals to the chassis on the port
designated as NT has dropped. The ifIndex corresponds to the port
designated as NT. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.24 |
xdslPortSpeedNormalThis trap signifies that the port speed of the
xDSL link has has gone above the threshold value.
This is a trap of 'warning' class. This trap compliments the
xdslPortSpeedLow Trap TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.102 |
xdslMarginNormalThis trap signifies that the margin estimate has gone
above a customer set threshold value. this is a trap
of 'minor' class. this trap compliments the xdslMarginLow
trap TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.103 |
xdslErrorRateNormalThis trap signifies that the error rate estimates
gone below a customer set threshold value. This is a trap
of 'minor' class. This trap compliments the xdslErrorRateHigh trap. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.104 |
xdslPortOperationalThis trap signifies that the modem set which was bad is now operational.
This is a trap of 'major' class. This trap compliments the
xdslPortFailure trap. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.105 |
xdslTestOverThis trap signifies that the test has completed on one of the
ports. This trap compliments the xdslTestStart trap. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.106 |
xdslRtuTypeMismatchClearThe RTU configured in the DSL card does match with the RTU connected
to the DSL port indicated by the ifIndex. TRAP-TYPE .1.3.6.1.4.1.7745.5.3.1.1.0.107 |
xdslDevIfStats OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.1 |
xdslDevIfIntervalStatsTableThe xdslIfStatsTable provides statistics specific to the xDSL
link. Statistics are collected on a per port basis and
on specified intervals. Hence as such this table is
indexed by the xdslDevIfStatsIfIndex and
xdslDevIfStatsInterval. Also Statistics are grouped
into remote and central statistics. By 'remote' we mean the
statistics collected by the device at the customer premises
and by 'central' we mean the statistics collected by the
device located at the central office. The objects which
are not grouped into these two groups are related to both
ends of the xDSL link. SEQUENCE OF XdslDevIfIntervalStatsEntry .1.3.6.1.4.1.7745.5.3.1.1.1.1 |
xdslDevIfIntervalStatsEntryDescribes a specific xDSL satistics entry. XdslDevIfIntervalStatsEntry .1.3.6.1.4.1.7745.5.3.1.1.1.1.1 |
xdslDevIfStatsIfIndexThe value of this object corresponds directly to each
DSL interface as described in ifTable.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.1 |
xdslDevIfStatsIntervalThe value of this object corresponds to the
interval of time during which statistics were
collected. previousDay(32) will have the statistics
collected from 12 midnight previous calendar dayro Enumeration .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.2 |
xdslDevIfStatsValid15MinuteIntervalCountReflects the number of 15 minute intervals
during which link was up and statistics were
received from the remote endro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.3 |
xdslDevIfStatsElapsedTimeLinkUpReflects the elapsed time since the link was up.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.4 |
xdslDevIfStatsLinkDownCountReflects the number of times that the xDSL link has gone to a
down state. This may be due to shutting down of the
customers side of the link. It could also be due to error
conditions which result in the going down. A large number of
these per unit time (synchronized off sysUpTime) would be
indicative of an error condition.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.5 |
xdslDevIfStatsUpStreamSpeedThe speed in the upstream (from the remote
to the central site) direction. This object
compliments the ifSpeed object in the ifTable which
represents the speed in the downstream (from the
central to the remote site) direction. The speed
is measured in bits per second.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.6 |
xdslDevIfStatsCentralReceiverGainReflects the receiver gain at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.7 |
xdslDevIfStatsCentralRecMarginReflects the margin at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.8 |
xdslDevIfStatsCentralRecAttenuationEstimateReflects the attenuation estimate at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.9 |
xdslDevIfStatsCentralRecTransmitPowerReflects the transmit power at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.10 |
xdslDevIfStatsCentralRecErrorRateReflects the error rate at the central site. This string
will represent a floating point number of the form.
[ErrRate][eE][+-][ErrRateBase] where ErrRate and ErrRateBase
are integers. In Other Words
ErrRate * [10^ -ErrRateBase]
shown below are example of the values returned.
123456E-5 = 1.23456
344567e-6 = 0.344567ro DisplayString .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.11 |
xdslDevIfStatsCentralRecErroredSecondsReflects the errored seconds at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.12 |
xdslDevIfStatsCentralRecSeverelyErroredSecondsReflects the severely errored seconds at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.13 |
xdslDevIfStatsRemoteReceiverGainReflects the receiver gain at the remote sitero INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.14 |
xdslDevIfStatsRemoteRecMarginReflects the margin at the remote sitero INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.15 |
xdslDevIfStatsRemoteRecAttenuationEstimateReflects the attenuation estimate at the remote sitero INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.16 |
xdslDevIfStatsRemoteRecTransmitPowerReflects the transmit power at the remote site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.17 |
xdslDevIfStatsRemoteRecErrorRateReflects the error rate at the remote site. This string
will represent a floating point number of the form a.b.
[ErrRate][eE][+-][ErrRateBase] where ErrRate and ErrRateBase
are integers. In Other Words
ErrRate * [10^ -ErrRateBase]
shown below are example of the values returned.
123456E-5 = 1.23456
344567e-6 = 0.344567ro DisplayString .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.18 |
xdslDevIfStatsRemoteRecErroredSecondsReflects the errored seconds at the remote site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.19 |
xdslDevIfStatsRemoteRecSeverelyErroredSecondsReflects the severely errored seconds at the remote site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.20 |
xdslDevIfStatsRemoteOctetsCorrectedThis object reflects the number of octets corrected
when reed-solomon is turned on at the remote site.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.21 |
xdslDevIfStatsRemoteOctetsNotCorrectedThis object reflects the number of octets not corrected
when reed-solomon is turned on at the remote site.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.22 |
xdslDevIfStatsRemoteReceivedKiloOctetsThe number of octets that have been received by the xDSL
interface at the remote site divided by 1000.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.23 |
xdslDevIfStatsRemoteReceivedPktsThe number of good packets that have been received by
the xDSL interface at the remote site.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.24 |
xdslDevIfStatsRemoteRecErrPktsReflects the number packet receive with error by the xDSL
interface at the remote site.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.25 |
xdslDevIfStatsRemoteDroppedPktsReflects the number of good packets that have been
received by the xDSL interface at the remote site,
but have been dropped due to insufficient buffer capacity.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.26 |
xdslDevIfStatsRemoteTransmittedKiloOctetsThe number of octets that have been transmitted by the
xDSL interface at the remote site divided by 1000.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.27 |
xdslDevIfStatsRemoteTransmittedPktsThe number of pkts that have been transmitted by the
xDSL interface at the remote site.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.28 |
xdslDevIfStatsCentralRecErroredMinutesReflects the errored minutes at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.29 |
xdslDevIfStatsCentralRecSeverelyErroredMinutesReflects the severely errored minutes at the central site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.30 |
xdslDevIfStatsRemoteRecErroredMinutesReflects the errored minutes at the remote site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.31 |
xdslDevIfStatsRemoteRecSeverelyErroredMinutesReflects the severely errored minutes at the remote site.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.32 |
xdslDevIfStatsCentralReceivedKiloOctetsThe number of octets that have been received by the xDSL
interface at the central site divided by 1000.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.33 |
xdslDevIfStatsCentralTransmittedKiloOctetsThe number of octets that have been transmitted by the
xDSL interface at the central site divided by 1000.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.34 |
xdslDevIfStatsCentralTransmittedPktsThe number of packets that have been transmitted by the
xDSL interface at the central site.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.35 |
xdslDevIfStatsCentralReceivedPktsThe number of packets that have been received by the
xDSL interface at the central site.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.36 |
xdslDevIfStatsCentralErrPktsThe number of packets that have been received by the
xDSL interface at the central site with error.ro Counter .1.3.6.1.4.1.7745.5.3.1.1.1.1.1.37 |
xdslDevIfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.2 |
xdslDevIfConfigTableThe xdslDevIfConfigTable provides config information specific
to a xDSL device, or system. The table is indexed by an
object which corresponds to ifIndex. These ifIndex entries,
themselves, denote and identify specific xdsl interfaces on
the board or module. Also the configuration parameters are
grouped into two broad categories, 'up' and 'down'. 'up'
reflects the upstream direction (from the customer premises
to the central office). 'Down' reflects the downstream
direction (from the central office to the customer premises) SEQUENCE OF XdslDevIfConfigEntry .1.3.6.1.4.1.7745.5.3.1.1.2.1 |
xdslDevIfConfigEntryDescribes a specific xDSL interface entry. XdslDevIfConfigEntry .1.3.6.1.4.1.7745.5.3.1.1.2.1.1 |
xdslDevIfConfigIfIndexThe value of this object corresponds directly to each xDSL
interface as described in ifTable.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.1 |
xdslDevIfConfigPortSpeedBehaviourThe value of this object corresponds to the
behaviour of the specified port. The default
value for this object is fixed (1).rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.2 |
xdslDevIfConfigUpFixedPortSpeedThe value of this object corresponds to the upstream
speed of the specified port for fixed port speed
behaviour. All the speeds enumerated above are in kbps.
If the port speed behaviour is adaptive an error of
noSuchName will be returned by the agent.
The default value for this object is s1088 (7).rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.3 |
xdslDevIfConfigDownFixedPortSpeedThe value of this object corresponds to the downstream
speed of the specified port for fixed port speed
behaviour. All the speeds enumerated above are in kbps.
if the port speed behaviour is adaptive an error of noSuchName
will be returned by the agent.
The default value for this object is s2560 (7).rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.4 |
xdslDevIfConfigUpAdaptiveUpperBoundPortSpeedThe value of this object corresponds to the
upper bound for the upstream port speed of the specified port
for adaptive port speed behaviour. The speeds are measured
in kbps. If the port speed behaviour is fixed an error of
noSuchName will be returned by the agent. The default value for
this object is s1088.rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.5 |
xdslDevIfConfigUpAdaptiveLowerBoundPortSpeedThe value of this object corresponds to the
lower bound for the upstream port speed of the
specified port for adaptive port speed behaviour
in kbps. If the port speed behaviour is fixed an
error of noSuchName will be returned by the agent.
The default value for this object s272.rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.6 |
xdslDevIfConfigDownAdaptiveUpperBoundPortSpeedThe value of this object corresponds to
the upper bound allowed for the downstream port speed
of the specified port for adaptive port speed
behaviour. The speeds are measured in kbps.
if the port speed behaviour is fixed an error of noSuchName
will be returned by the agent. The default value for this
object is s2560 (7).rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.7 |
xdslDevIfConfigDownAdaptiveLowerBoundPortSpeedThe value of this object corresponds to the
Minimum lower bound allowed for the downstream port speed
of the specified port for adaptive port speed behaviour.
If the port speed behaviour is fixed an error of noSuchName
will be returned by the agent. The speeds are measured in kbps.
The default value for this object is s640(1).rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.8 |
xdslDevIfConfigReedSolomonDownForwardErrorCorrectionThe value of this object corresponds to the
Reed-Solomon forward error correction in the downstream
direction. The default value of this object should be
minimizeError (1).rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.9 |
xdslDevIfConfigMarginThresholdThe value of this object corresponds to the offset from
the startup margin. The threshold margin is calculated
by subtracting the offset from the startup margin.
Permissible range of values are between -7 and 14.
A value of -9999 disables the threshold check. The default
value of this object is 3rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.10 |
xdslDevIfConfigEstimatedHrErrRateThresholdThe value of this object corresponds to the
estimated error rate threshold value on an hourly basis.
A value of -9999 disables the threshold check. The default value
for this object is 1000.rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.11 |
xdslDevIfConfigEstimatedDayErrRateThresholdThe value of this object corresponds to the
estimated error rate threshold value on a daily basis. A
value of -9999 disables this threshold check. The default value
for this object is 10000rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.12 |
xdslDevIfConfigPortIDThe value of this object corresponds to 40 character
information only field that identifies what the DSL
port is connected to (Circuit ID, MDF location,
Customer name, etc.)rw DisplayString .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.13 |
xdslDevIfLinkUpDownTransitionThresholdThe value of this object corresponds to the threshold
value for link up-down transitions. If link up-down's exceed
this threshold value a xdslLinkupDownTransitions
trap is generated. This value would represent the number
of link up-down transitions in a 15 minute interval. A value
of -9999 disables the threshold check. The default value for this
object is 0rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.14 |
xdslDevIfConfigStartUpMarginThe value of this object corresponds to the startup value
of the margin for a DSL interface (specified by ifIndex).
The unit is db (decibels. The higher the margin the better
the quality of the line. The default value of this object is 3.rw INTEGER (-3..9) .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.15 |
xdslDevIfConfigTxPowerAttenuationThis value corresponds to the Transmitt Power Attenuation in dB
for the access node. This value represents the downstream power
level in dB. Permissible range of values are between -6 and 0.
The default value of this object is 0 dB. The power levels +3
and +6 may be used in future.rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.16 |
xdslDevIfConfigSnTxPowerAttenuationThis value corresponds to the Transmitt Power Attenuation in dB
for the service node. This value represents the upstream power
level in dB. The default value of this object is -6 dB.rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.2.1.1.17 |
xdslRemoteSys OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.3 |
xdslRemoteSysTableThe Remote System information table. This table is based
on the mib-2 system mib. SEQUENCE OF XdslRemoteSysEntry .1.3.6.1.4.1.7745.5.3.1.1.3.1 |
xdslRemoteSysEntryDescribes a specific xDSL interface Remote Endpoint entry. XdslRemoteSysEntry .1.3.6.1.4.1.7745.5.3.1.1.3.1.1 |
xdslRemoteSysIndexRefer to the mib-2 system MIB for a description.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.1 |
xdslRemoteSysDescrRefer to the mib-2 system MIB for a description.ro DisplayString .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.2 |
xdslRemoteSysObjectIDRefer to the mib-2 system MIB for a description.ro OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.3 |
xdslRemoteSysUpTimeRefer to the mib-2 system MIB for a description.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.4 |
xdslRemoteSysContactRefer to the mib-2 system MIB for a description.rw DisplayString .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.5 |
xdslRemoteSysNameRefer to the mib-2 system MIB for a description.rw DisplayString .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.6 |
xdslRemoteSysLocationRefer to the mib-2 system MIB for a description.rw DisplayString .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.7 |
xdslRemoteSysServicesRefer to the mib-2 system MIB for a description.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.8 |
xdslRemoteSysCircuitIdThe value of this object reflects the Circuit ID
for a Service Node.ro DisplayString .1.3.6.1.4.1.7745.5.3.1.1.3.1.1.9 |
xdslRemoteDTEStatus OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.4 |
xdslRemoteDTEStatusTableThe Remote DTE Status table. This provides status information about the
DTE port of the DSL RTUs. SEQUENCE OF XdslRemoteDTEStatusEntry .1.3.6.1.4.1.7745.5.3.1.1.4.1 |
xdslRemoteDTEStatusEntryThis provides status information about the
DTE port of a specific DSL RTU. XdslRemoteDTEStatusEntry .1.3.6.1.4.1.7745.5.3.1.1.4.1.1 |
xdslRemoteDTEStatusIndexThe value of this object corresponds directly to each DSL interface as
described in the ifTable.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.4.1.1.1 |
xdslRemoteDTEStateThe value of this object reflects the state of the DTE interface of the
DSL RTU.ro Enumeration .1.3.6.1.4.1.7745.5.3.1.1.4.1.1.2 |
xdslRemoteDTETypeThe value of this object reflects the configuration of the DTE interface
of the DSL RTU.ro Enumeration .1.3.6.1.4.1.7745.5.3.1.1.4.1.1.3 |
xdslRemoteDTEClockSourceThe value of this object reflects the timing configuration of the DTE
interface of the DSL RTU.ro Enumeration .1.3.6.1.4.1.7745.5.3.1.1.4.1.1.4 |
xdslRemoteDTEStrobeThe value of this object reflects the clock edge timing configuration of the DTE
interface of the DSL RTU.ro Enumeration .1.3.6.1.4.1.7745.5.3.1.1.4.1.1.5 |
xdslRemoteDTELoopbackStateThe value of this object reflects the loopback state of the DTE
interface of the DSL RTU.ro Enumeration .1.3.6.1.4.1.7745.5.3.1.1.4.1.1.6 |
xdslDevMvlIfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.5 |
xdslDevMvlIfConfigTableThe xdslDevMvlIfConfigTable provides config information specific
to a xDSL(MVL) device, or system. The table is indexed by an
object which corresponds to ifIndex. These ifIndex entries,
themselves, denote and identify specific xdsl(Mvl) interfaces on
the board or module. SEQUENCE OF XdslDevMvlIfConfigEntry .1.3.6.1.4.1.7745.5.3.1.1.5.1 |
xdslDevMvlIfConfigEntryDescribes a specific xDSL(MVL) interface entry. XdslDevMvlIfConfigEntry .1.3.6.1.4.1.7745.5.3.1.1.5.1.1 |
xdslDevMvlIfConfigIfIndexThe value of this object corresponds directly to each xDSL(MVL)
interface as described in ifTable.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.5.1.1.1 |
xdslDevMvlIfConfigUpperBoundPortSpeedThe value of this object corresponds to the upper bound
port speed of the specified port. The speeds are measured in kbps.
Supported speeds are 128, 192, 256, 320, 384, 448, 512
576, 640, 704, 768.
The default value of this object is 768rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.5.1.1.2 |
xdslDevMvlIfConfigMarginThresholdThe value of this object corresponds to the
Margin threshold value. Permissible range of
values are between -5 and 9. A value of -9999
disables the threshold check. The default value is 3rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.5.1.1.3 |
xdslDevMvlIfConfigPortIDThe value of this object corresponds to 40 character
information only field that identifies what the DSL
port is connected to (Circuit ID, MDF location,
Customer name, etc.)rw DisplayString .1.3.6.1.4.1.7745.5.3.1.1.5.1.1.4 |
xdslDevMvlIfLinkUpDownTransitionThresholdThe value of this object corresponds to the threshold
value for link up-down transitions. If link up-down's exceed
this threshold value a xdslLinkupDownTransitions
trap is generated. This value would represent the number
of link up-down transitions in a 15 minute interval. A value
of -9999 disables the threshold check. The default value for this
object is 0rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.5.1.1.5 |
xdslDevMvlIfConfigOnHookTxPowerAttenuationThis value corresponds to the On-hook Transmitt Power Attenuation
in dB for the access node and the service node. This value represents
both downstream and upstream power level in dB while the phone is
On-hook. Permissible range of values are between -2 and +10. The
default value of this object is 10 dB.rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.5.1.1.6 |
xdslDevMvlIfConfigOffHookTxPowerAttenuationThis value corresponds to the Off-hook Transmitt Power Attenuation
in dB for the access node and the service node. This value represents
both downstream and upstream power level in dB while the phone is
Off-hook. Permissible range of values are between -2 and +7. The
default value of this object is 7 dB.rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.5.1.1.7 |
xdslDevNAPCustomerAccount OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.6 |
xdslDevNAPCustomerAccountTableThe xdslDevNAPCustomerAccountTable provides customer accounting
information on each DSL port. Network Access Providers can accurately
bill their end station DSL customers by the amount of usage.
The table is indexed by ifIndex and xdslDevNAPCustomerAccountInterval
The ifIndex identifies specific xdsl interface on the device and
xdslDevNAPCustomerAccountInterval specifies the accounting information
is for the current day or the previous day. Customer data excludes all
traffic used for management purpose. SEQUENCE OF XdslDevNAPCustomerAccountEntry .1.3.6.1.4.1.7745.5.3.1.1.6.1 |
xdslDevNAPCustomerAccountEntryProvides customer related accounting information specific to an
xDSL interface entry. XdslDevNAPCustomerAccountEntry .1.3.6.1.4.1.7745.5.3.1.1.6.1.1 |
xdslDevNAPCustomerAccountIfIndexThe value of this object corresponds directly to each xDSL
interface as described in ifTable.ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.6.1.1.1 |
xdslDevNAPCustomerAccountIntervalThe value of this object corresponds to the interval of time
during which customer accounting data were collected. Day
starts at 12.01 midnightro Enumeration .1.3.6.1.4.1.7745.5.3.1.1.6.1.1.2 |
xdslDevNAPCustomerAccountRecKiloOctetsCustomer data received at the AN's DSL port in 1000 Octets.
The default value of this object is 0ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.6.1.1.3 |
xdslDevNAPCustomerAccountTrxKiloOctetsCustomer data transmitted over the AN's DSL port in 1000 Octets.
The default value of this object is 0ro INTEGER .1.3.6.1.4.1.7745.5.3.1.1.6.1.1.4 |
xdslLinkUpDownInformation OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.7 |
xdslLinkDownReasonThis entry contains the reason as to why
the DSL Link went down. This information
is obtained when the DSL Link is coming up DisplayString .1.3.6.1.4.1.7745.5.3.1.1.7.1 |
xdslRemoteInjection OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.8 |
xdslRemoteInjectionTypeThe value of this object corresponds to the remote
injection typedeprecated Enumeration .1.3.6.1.4.1.7745.5.3.1.1.8.1 |
xdslDevIDSLConfig OBJECT IDENTIFIER .1.3.6.1.4.1.7745.5.3.1.1.9 |
xdslDevIDSLConfigTableThe xdslDevIDSLConfigTable provides configuration specific to the IDSL link. SEQUENCE OF XdslDevIDSLConfigEntry .1.3.6.1.4.1.7745.5.3.1.1.9.1 |
xdslDevIDSLConfigEntryDescribes a specific IDSL configuration entry. XdslDevIDSLConfigEntry .1.3.6.1.4.1.7745.5.3.1.1.9.1.1 |
xdslDevIDSLConfigPortSpeedBehaviourThe value of this object corresponds to the
behaviour of the specified port. The default
value for this object is fixed (1).rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.9.1.1.1 |
xdslDevIDSLConfigPortSpeedThe value of this object corresponds to both upstream
and downstream speed of the specified port. All the
speeds are in kbps. The default value for this object
is 128 kbps.rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.9.1.1.2 |
xdslDevIDSLConfigPortIDThe value of this object corresponds to 40 character
information only field that identifies what the DSL
port is connected to (Circuit ID, MDF location,
Customer name, etc.)rw DisplayString .1.3.6.1.4.1.7745.5.3.1.1.9.1.1.3 |
xdslDevIDSLTimingPortTransceiverModeThe transceiver mode selected on the timing source port.
Only one IDSL port can be set to NT mode. This timing
will then be distributed to all other IDSL ports in the
chassis that are set to LT.
The selected xdslDevIDSLPrimaryTimingSourcePort provides clocking
signals to the DSLAM when the transceiver mode is set to Network
timing. The port selected for Network Timing mode will probably not
used for customer data, but will receive a 2.048 Mhz Network clocking
signal from a central office timing source and distribute this timing
to other IDSL port cards.rw Enumeration .1.3.6.1.4.1.7745.5.3.1.1.9.1.1.4 |
xdslDevIDSLConfigMarginThresholdThe value of this object corresponds to the
Margin threshold value. A value of -9999 disables the
threshold check. The value range of this object is
-5 to 10. The default value is 3rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.9.1.1.5 |
xdslDevIDSLLinkUpDownTransitionThresholdThe value of this object corresponds to the threshold
value for link up-down transitions. If link up-down's exceed
this threshold value a xdslLinkupDownTransitions
trap is generated. This value would represent the number
of link up-down transitions in a 15 minute interval. A value
of -9999 disables the threshold check. The value range of this
object is 0 to 1000. The default value for this object is 0rw INTEGER .1.3.6.1.4.1.7745.5.3.1.1.9.1.1.6 |