HH3C-LAG-MIB
AI MIB Summary
The HH3C-LAG-MIB module enables monitoring and management of Link Aggregation Control Protocol (LACP) extended attributes on H3C network devices, specifically tracking LAG group states, member port status, and aggregation session parameters.
LACP extend MIB.
Main OID:
hh3cLAG.1.3.6.1.4.1.25506.8.25
26
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
26 total| Object Name |
|---|
hh3cLAGLACP extend MIB. MODULE-IDENTITY .1.3.6.1.4.1.25506.8.25 |
hh3cLAGMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.25506.8.25.1 |
hh3cAggLinkTableA table of aggregate link objects. SEQUENCE OF Hh3cAggLinkEntry .1.3.6.1.4.1.25506.8.25.1.1 |
hh3cAggLinkEntryEntry of table. Hh3cAggLinkEntry .1.3.6.1.4.1.25506.8.25.1.1.1 |
hh3cAggLinkNumberThe serial number of aggregation group.ro Integer32 .1.3.6.1.4.1.25506.8.25.1.1.1.1 |
hh3cAggLinkNameAggregation name.rw DisplayString .1.3.6.1.4.1.25506.8.25.1.1.1.2 |
hh3cAggLinkModeType of aggregation.
manual: Manual aggregation, no LACP.
static: Membership specified by user, LACP is
used to validate.
dynamic: Completely dynamic aggregation detected
by LACP.rw Enumeration .1.3.6.1.4.1.25506.8.25.1.1.1.3 |
hh3cAggLinkPortListList of ports in this link aggregation group, by bridge port
number. If the mode of the link aggregation group is manual
or static, you can update this list to your
hearts content. However, if the link aggregation group is
dynamic, the system will maintain it. You are not
permitted to set the value of this to
all zeroes.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.25506.8.25.1.1.1.4 |
hh3cAggLinkStateRowStatus, now support three states:
createAndGo, active, destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.8.25.1.1.1.5 |
hh3cAggPortListSelectedPortsA PortList of physical ports that have been
selected but not attached to this aggregator.
When the bit is set to 1,it means the
corresponding port is in the portlist.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.25506.8.25.1.1.1.6 |
hh3cAggPortListSamePartnerPortsPortList of physical ports that have the
same Actor SystemID and partner systemID as
this aggregator, but have different actor
and partner keys of aggregator.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.25506.8.25.1.1.1.7 |
hh3cAggPortTableA table of aggregate port objects. SEQUENCE OF Hh3cAggPortEntry .1.3.6.1.4.1.25506.8.25.1.2 |
hh3cAggPortEntryEntry of table. Hh3cAggPortEntry .1.3.6.1.4.1.25506.8.25.1.2.1 |
hh3cAggPortIndexPort ifindex which is according to RFC1213 MIB.ro Gauge32 .1.3.6.1.4.1.25506.8.25.1.2.1.1 |
hh3cAggPortNotAttachedReasonReason why this port is selected for an
aggregator but not attached,
0: The port is attached to this aggregator.
1: The current number of active ports has
reached the upper limit.
2: All aggregation resources are already in-use.
3: The port's configuration is improper
for being attached.
4: The port's partner is improper for being attached.
5: The number of current active ports
has not reached the lower limit.
6: The port's physical state (down) is
improper for being attached.
7: The port is not selected for an aggregator.
8: The port's hardware restriction is
improper for being attached.
9: The port's speed is improper for being attached.
10: The port's duplex mode is improper for being attached.rw Integer32 .1.3.6.1.4.1.25506.8.25.1.2.1.2 |
hh3cAggPortLacpStateControl ports' lacp enble or disable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.8.25.1.2.1.3 |
hh3cAggPortNotAttachedStringThe string which interprets this
port is selected for an aggregator
but not attached.rw DisplayString .1.3.6.1.4.1.25506.8.25.1.2.1.4 |
hh3cAggResourceAllocationValueThe priority value calculated to decide which
aggregations have first call on the load-sharing
aggregation resources in the hardware. It
depends on the aggregation type and total
speed.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.25506.8.25.1.3 |
hh3cLAGMibNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.25506.8.25.2 |
hh3cAggSpeedChangedNotificationThis event will be triggered whenever an
aggregation changes its speed. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.8.25.2.1 |
hh3cAggPortInactiveNotificationThis event will be triggered whenever any port
in aggregator is made inactive. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.8.25.2.2 |
hh3cAggPortInactiveNotification2This event will be triggered whenever the port
in aggregator is made inactive. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.8.25.2.3 |
hh3cAggPortActiveNotificationThis event will be triggered whenever the port
in aggregator is made active. NOTIFICATION-TYPE .1.3.6.1.4.1.25506.8.25.2.4 |
hh3cLAGMibConformance OBJECT IDENTIFIER .1.3.6.1.4.1.25506.8.25.3 |
hh3cLAGMibCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.25506.8.25.3.1 |
hh3cLAGMibGroup OBJECT IDENTIFIER .1.3.6.1.4.1.25506.8.25.3.2 |