H3C-DOT11-CFG-MIB
AI MIB Summary
The H3C-DOT11-CFG-MIB module provides SNMP-based configuration and monitoring capabilities for H3C wireless LAN infrastructure, specifically managing Access Point (AP) states, BSS parameters, and authentication key management (AKM) settings across both Fat and Fit AP architectures. It enables administrators to retrieve and modify critical 802.11 radio parameters, association policies, and CAPWAP tunnel configurations required to maintain interoperability between wireless clients and the wired distribution system.
This MIB provides information about WLAN configuration.
GLOSSARY
IEEE 802.11 Standard to encourage interoperability among wireless networking equipment.
Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network.
Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network.
Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC.
Fit AP Applied in the enterprise environment, it will work under the control and management from AC.
Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP.
BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP.
Radio The chip set to receive and send wireless signal.
Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.)
Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association.
MSDU MAC Service Data Unit, it is frame format defined by
802.11.
TU It is 1,024 microseconds (ms), which is about 1 millisecond.
AKM The authentication and key management method defined by
802.11i, and which includes 802.1x and pre-shared key.
Main OID:
h3cDot11CFG.1.3.6.1.4.1.2011.10.2.75.4
310
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
310 total| Object Name |
|---|
h3cDot11CFGThis MIB provides information about WLAN configuration.
GLOSSARY
IEEE 802.11
Standard to encourage interoperability among
wireless networking equipment.
Access point (AP)
Transmitter/receiver (transceiver) device
that commonly connects and transports data
between a wireless network and a wired network.
Access control (AC)
To control and manage multi-APs, it will bridge
wireless and wired network.
Fat AP
Applied in the home, SOHO and so on, and it could
work independently without help from AC.
Fit AP
Applied in the enterprise environment, it will work
under the control and management from AC.
Control And Provisioning of Wireless Access Points Protocol
The short name of protocol is CAPWAP. AC will control
and manage AP by CAPWAP tunnel protocol defined by IETF.
Also, a data tunnel will be set up between AC and AP.
BSS
IEEE 802.11 Basic Service Set (Radio Cell). The
BSS of an AP comprises of the stations directly
associating with the AP.
Radio
The chip set to receive and send wireless signal.
Association
The service used to establish access point
or station mapping and enable station invocation
of the distribution system services.
(Wireless clients attempt to connect to
access points.)
Basic Rate
A data rate that is mandatory for client
devices to support in order for them to achieve
successful association.
MSDU
MAC Service Data Unit, it is frame format defined by
802.11.
TU
It is 1,024 microseconds (ms), which is about 1
millisecond.
AKM
The authentication and key management method defined by
802.11i, and which includes 802.1x and pre-shared key. MODULE-IDENTITY .1.3.6.1.4.1.2011.10.2.75.4 |
h3cDot11GlobeConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.1 |
h3cDot11GlobalCountryCodeRepresents the country code for wireless network.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.1.1 |
h3cDot11StaKeepALiveTimerIntvlRepresents the interval of the keep alive requests sent between
AP and STA.
Default value 0 : The keep alive function is disabled.rw Unsigned32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.1.2 |
h3cDot11StaIdleTimerIntvlRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.1.3 |
h3cDot11BroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.1.4 |
h3cDot11APScanModeRepresents the scanning mode for AP.
The following values are supported:
active(1), - AP will actively do scan.
passive(2) - AP will passively do scan.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.1.5 |
h3cDot11ACCtrlTunnelSecSupportRepresents what security schemes are supported for CAPWAP Control
tunnel.rw H3cDot11TunnelSecSchemType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.1.6 |
h3cDot11ACDataTunnelSecSupportRepresents what security schemes are supported for CAPWAP data
tunnel. The cleartxt is the default scheme.rw H3cDot11TunnelSecSchemType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.1.7 |
h3cDot11ACAutoAPSupportRepresents enable the auto AP functionality or not.
'true' : The auto AP functionality is enabled.
'false': The auto AP functionality is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.1.8 |
h3cDot11AutoAPNameRepresents the name of auto AP which need to be made persistent.
When read the value from the node, NULL value be returned.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.1.9 |
h3cDot11PersistentNameRepresents the new name of auto AP after being made persistent.
When read the value from the node, NULL value be returned.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.1.10 |
h3cDot11IntfTrapThresholdRepresents threshold of interference trap. If signal strength of
the device exceeds this threshold, corresponding trap will
be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.4.1.11 |
h3cDot11MonitorIntervalRepresents the monitoring interval.
Default value 0 : The monitoring functionality is changed to
real-time mode.rw Unsigned32(0 | 5..15) UNITS "minute" .1.3.6.1.4.1.2011.10.2.75.4.1.12 |
h3cDot11SampleIntervalRepresents the sampling interval.
Default value 0 : The sampling functionality is disabled.rw Unsigned32(0 | 10..300) UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.1.13 |
h3cDot11ChnlSwitChkIntervalRepresents the checking interval of channel switch.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.1.14 |
h3cDot11APUserUplimitRepresents the upper limit of user which has access to this AP.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.1.15 |
h3cDot11APL2IsolateEnableRepresents enable the layer2 isolation or not.
'true' : The layer2 isolation functionality is enabled.
'false': The layer2 isolation functionality is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.1.16 |
h3cDot11APBSSIDSupportNumRepresents the max number of BSSID supported by Current AP.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.1.17 |
h3cDot11APLastUpdateStatTimeRepresents date and time update statistic information lately.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.1.18 |
h3cDot11APDoSProtectEnableRepresents enable the DOS protection or not.
'true' : The DOS protection functionality is enabled.
'false': The DOS protection functionality is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.1.19 |
h3cDot11MaxAPPerIfRepresents max AP number that can be connected to AC interface.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.1.20 |
h3cDot11SampleTimeStampRepresents the start time of current sample period.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.1.21 |
h3cDot11UplinkTrackIdRepresents the track id of AP.
Default value 0 : The uplink track function for AP is disabled.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.1.22 |
h3cDot11RtCollectSwitchThis object is used to turn on/off real-time statistics collection
between AC and AP. If the value is true, h3cDot11RtCollectIntvl will
take effect. Otherwise, h3cDot11RglCollectIntvl will take effect.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.1.23 |
h3cDot11RglCollectIntvlThis object represents interval to regularly collect statistics from
AC to AP.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.1.24 |
h3cDot11RtCollectIntvlThis object represents interval to collect real-time statistics from
AC to AP.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.1.25 |
h3cDot11AllAPCpuUsageThresholdThe CPU usage threshold for all AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.1.26 |
h3cDot11AllAPMemUsageThresholdThe memory usage threshold for all AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.1.27 |
h3cDot11AdjIntfTrapThresholdRepresents threshold of adjacent interference trap. If signal strength
of the device exceeds this threshold, corresponding trap will be sent.rw Integer32 UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.4.1.28 |
h3cDot11AllAPMonitorModeRepresents what work mode for All AP.
The following values are supported:
normal, - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.1.29 |
h3cDot11PolicyConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.2 |
h3cDot11RadioPolicyTableThe table defines the parameters for radio policy, as per
radio policy of CLI.
One radio policy could be assigned to the different radios (AP). SEQUENCE OF H3cDot11RadioPolicyEntry .1.3.6.1.4.1.2011.10.2.75.4.2.1 |
h3cDot11RadioPolicyEntryEach entry contains information of each radio policy. H3cDot11RadioPolicyEntry .1.3.6.1.4.1.2011.10.2.75.4.2.1.1 |
h3cDot11RadioPolicyNameRepresents the name of radio policy. OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.1 |
h3cDot11BeaconIntervalRepresents the interval for Beacon management frame.rw Integer32 UNITS "TU" .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.2 |
h3cDot11DtimIntervalRepresents the number of beacon intervals that shall elapse
between transmission of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM Count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.3 |
h3cDot11RtsThresholdRepresents the current minimum size,in octets,of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "byte" .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.4 |
h3cDot11FragThresholdRepresents the current maximum size, in octets, of the MPDU that
may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "byte" .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.5 |
h3cDot11ShortRetryThresholdRepresents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
h3cDot11RTSThreshold, that shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.6 |
h3cDot11LongRetryThresholdRepresents the maximum number of transmission attempts of a
frame, the length of which is longer than h3cDot11RTSThreshold,
that shall be made before a failure condition is indicated.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.7 |
h3cDot11MaxRxLifetimeRepresents the elapsed time. After the time specified by
h3cDot11MaxRxLifetime, the further attempts to reassemble the
MSDU shall be terminated.rw Unsigned32 UNITS "millisecond" .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.8 |
h3cDot11RdoPolicyRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.9 |
h3cDot11RdoClientMaxCountRepresent the maximum number of stations supported by
this radio policy.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.10 |
h3cDot11BeaconIntervalMsRepresents the interval for Beacon management frame.rw Integer32 UNITS "ms" .1.3.6.1.4.1.2011.10.2.75.4.2.1.1.11 |
h3cDot11ServicePolicyTableThe table defines the parameters for ESS, as per service policy
of CLI.
One service policy could be assigned to the different radios
(AP). SEQUENCE OF H3cDot11ServicePolicyEntry .1.3.6.1.4.1.2011.10.2.75.4.2.2 |
h3cDot11ServicePolicyEntryEach entry contains information of each service policy. H3cDot11ServicePolicyEntry .1.3.6.1.4.1.2011.10.2.75.4.2.2.1 |
h3cDot11ServicePolicyIDRepresents the ID of each service policy. H3cDot11ServicePolicyIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.1 |
h3cDot11SSIDNameRepresents the ESS. As per CLI, the value of
service policy name will be SSID.rw H3cDot11SSIDStringType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.2 |
h3cDot11SSIDHiddenThis attribute controls whether the SSID will be advertised in
the beacon frame.
If it is true, then SSID will not be advertised in the beacon
frame.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.3 |
h3cDot11AuthenModeRepresents the Authentication mode defined by 802.11.rw H3cDot11AuthenType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.4 |
h3cDot11SSIDEncryptionModeRepresents the encryption mode for this ESS.rw H3cDot11SSIDEncryptModeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.5 |
h3cDot11WlanInfBindingTypeRepresents the service policy will bind to what kind of
data forwarding interface.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.6 |
h3cDot11WlanInfBindingIDRepresents the interface ID of the interface that ESS will
bind to.
If the value is set to -1, the binding will be removed.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.7 |
h3cDot11SrvPolicyRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.8 |
h3cDot11ClientMaxCountRepresent the maximum number of stations supported by
this service policy.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.9 |
h3cDot11SPInCirModeCIR(committed information rate) mode of inbound direction.
This object is useful only when the corresponding CIR is nonzero.
If value of this object is changed, corresponding CIR will be reset.rw H3cDot11CirMode (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.10 |
h3cDot11SPInCirValueRepresents the CIR of inbound direction of this service policy.
If the value is 0, it means that no flow control is applied to
the service policy, and the corresponding CIR mode is meaningless.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.11 |
h3cDot11SPOutCirModeCIR(committed information rate) mode of outbound direction.
This object is useful only when the corresponding CIR is nonzero.
If value of this object is changed, corresponding CIR will be reset.rw H3cDot11CirMode (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.12 |
h3cDot11SPOutCirValueRepresents the CIR of outbound direction of this service policy.
If the value is 0, it means that no flow control is applied to
the service policy, and the corresponding CIR mode is meaningless.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.13 |
h3cDot11WlanInfPVIDRepresents the VLAN ID of SSID.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.14 |
h3cDot11SPInCirStaticValueRepresents the CIR of inbound direction for static CIR mode.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.15 |
h3cDot11SPOutCirStaticValueRepresents the CIR of outbound direction for static CIR mode.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.16 |
h3cDot11SPIsolateIf it is true, then stations connected with the service policy are
isolated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.17 |
h3cDot11WAPIAuthServerIPRepresents the IP address of the WAPI Authentication serverrw IpAddress .1.3.6.1.4.1.2011.10.2.75.4.2.2.1.18 |
h3cDot11ServicePolicyExtTableThe table defines the parameters for ESS, as per service policy
of CLI.
When the value of h3cDot11SSIDEncryptionMode equals to cipher(2),
more configuration for a ESS will be put into the table. SEQUENCE OF H3cDot11ServicePolicyExtEntry .1.3.6.1.4.1.2011.10.2.75.4.2.3 |
h3cDot11ServicePolicyExtEntryEach entry contains information of each service policy under cipher(2)
mode. H3cDot11ServicePolicyExtEntry .1.3.6.1.4.1.2011.10.2.75.4.2.3.1 |
h3cDot11ServicePolicyExtIDRepresents the ID of each service policy. H3cDot11ServicePolicyIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.3.1.1 |
h3cDot11SecIEStatusTo enable the security Information element in the beacon and
probe response frames sent by AP.rw H3cDot11SecIEStatusType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.3.1.2 |
h3cDot11SecurityCiphersThe WLAN system support the following cipher type for data frame
encryption.
wep40(2)
tkip(4)
aesccmp(16)
wep104(32)
wpisms4(64)
wep128(128)
For each service policy,it could support multiple cipher types at
the same time.So the value of object could combine multiple value
of cipher type above.
When the value of node equals to zero, it means no configuration or
undo operation.rw INTEGER .1.3.6.1.4.1.2011.10.2.75.4.2.3.1.3 |
h3cDot11CipherKeyIndexRepresents the key index of cipher key for packet.
When h3cDot11SecurityCiphers value is wep40 or wep104,
the configuration will take effective.rw INTEGER .1.3.6.1.4.1.2011.10.2.75.4.2.3.1.4 |
h3cDot11CipherKeyRepresents the cipher key for packet.
When h3cDot11SecurityCiphers value is wep40 or wep104,
the configuration will take effective.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.2.3.1.5 |
h3cDot11SrvPolicyExtRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.2.3.1.6 |
h3cDot11CipherKeyTypeRepresents the cipher key type of h3cDot11CipherKey.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.2.3.1.7 |
h3cDot11RadioPolicyExtTableThe table defines the radio policy of each radio.
It can't be modified if the radio policy is a default radio policy. SEQUENCE OF H3cDot11RadioPolicyExtEntry .1.3.6.1.4.1.2011.10.2.75.4.2.4 |
h3cDot11RadioPolicyExtEntryEach entry contains information of each radio policy. H3cDot11RadioPolicyExtEntry .1.3.6.1.4.1.2011.10.2.75.4.2.4.1 |
h3cDot11RPAPSerialIDThis object represents the Serial ID of AP. OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.1 |
h3cDot11RPRadioIDThis object represents each radio. H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.2 |
h3cDot11RPBeaconIntervalThis object represents the interval for Beacon management frame.rw Integer32 UNITS "milliseconds" .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.3 |
h3cDot11RPDtimIntervalThis object represents the number of beacon intervals that shall elapse
between transmissions of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.4 |
h3cDot11RPRtsThresholdThis object represents the current minimum size, in octets, of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "byte" .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.5 |
h3cDot11RPFragThresholdThis object represents the current maximum size, in octets, of the MPDU
that may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "byte" .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.6 |
h3cDot11RPShortRetryThresholdThis object represents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
h3cDot11RTSThreshold, that shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.7 |
h3cDot11RPLongRetryThresholdThis object represents the maximum number of transmission attempts of a
frame, the length of which is longer than h3cDot11RTSThreshold,
and that shall be made before a failure condition is indicated.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.8 |
h3cDot11RPClientMaxCountThis object represents the maximum number of stations supported by
this radio policy.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.2.4.1.9 |
h3cDot11SrvPortSecurityTableThis table defines the WLAN security status for ESS, BSS and
WLAN-Ethernet interface which binding the crypto service-template.
Otherwise, when binding the clear service-template,
h3cPortSecurityTables should be used to configure port security. SEQUENCE OF H3cDot11SrvPortSecurityEntry .1.3.6.1.4.1.2011.10.2.75.4.2.5 |
h3cDot11SrvPortSecurityEntryThere is a row in this table for service policy. H3cDot11SrvPortSecurityEntry .1.3.6.1.4.1.2011.10.2.75.4.2.5.1 |
h3cDot11SecurityServicePolicyIDRepresents the ID of each service policy. H3cDot11ServicePolicyIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.2.5.1.1 |
h3cDot11SrvPortSecurityModeDetermines the security modes of the WLAN port.
noRestrictions(1) The default value,no any security mode is set.
userLoginSecureExt(2) Access to the port is denied until the port
client is authorized (by 802.1X).
psk(3) Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
macAddressAndPsk(4) The MAC address is first authenticated and only if
this succeeds does the psk then attempt user authentication.
userLoginSecureExtOrPsk(5) This selects both the userLoginSecureExt and
psk modes together such that either is allowed to authorized access.
Which mode works for client depends on the client's choice.
ext(6) Access to the port is denied until the port client is
authenticated (by ext).rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.2.5.1.2 |
h3cDot11SrvSecurityKeyTypeThis indicates the key type in the 802.1X EAPOL_Key packet.
userLoginTxKeyTypeNone(1) This means the key type is not set yet.
userLoginTxKeyTypeDot11Key(2) This selects the 802.11 key type.
userLoginTxKeyTypeRsaRC4Key(3) This selects the RC4 key for RSA RC4
session encryption.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.2.5.1.3 |
h3cDot11SrvSecurityPskKeyModeThis is the password input mode. When input as pskKeyModePassPhrase,
h3cDot11SrvSecurityPskKeyString must be 8 to 63 characters;
when input as pskKeyModeRawKey, h3cDot11SrvSecurityPskKeyString
must be 64 characters and each character must be '0'-'9', 'a'-'f' and
'A'-'F'.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.2.5.1.4 |
h3cDot11SrvSecurityPskKeyStringThis is the password string used for psk authentication.rw DisplayString .1.3.6.1.4.1.2011.10.2.75.4.2.5.1.5 |
h3cDot11SrvPolicyExtendTableThe table defines the parameters of each service policy. SEQUENCE OF H3cDot11SrvPolicyExtendEntry .1.3.6.1.4.1.2011.10.2.75.4.2.6 |
h3cDot11SrvPolicyExtendEntryEach entry contains information of each service policy. H3cDot11SrvPolicyExtendEntry .1.3.6.1.4.1.2011.10.2.75.4.2.6.1 |
h3cDot11SPEnableRepresents whether the service policy is enabled.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.2.6.1.1 |
h3cDot11APConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.3 |
h3cDot11APTemplateTableBy AP template CLI, administrator will configure the parameters of AP
by convenience.
Before AP boot up and connect to AC by CAPWAP tunnel, administrator
will create AP template for each AP. When AP connect to AC,
AC will assign configuration to AP by h3cDot11APSerialID
information in AP template. SEQUENCE OF H3cDot11APTemplateEntry .1.3.6.1.4.1.2011.10.2.75.4.3.1 |
h3cDot11APTemplateEntryEach entry contains configuration information for each AP. H3cDot11APTemplateEntry .1.3.6.1.4.1.2011.10.2.75.4.3.1.1 |
h3cDot11APTemplateNameRepresents the name of AP template. OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.1 |
h3cDot11APSerialIDRepresents AP serial id.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.2 |
h3cDot11TemplateAPModelAliasRepresents the alias of AP model name.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.3 |
h3cDot11DescriptionThis attribute will give more information about AP.
Administrator could suggest the location, owner or
other information for each AP.
If the value is set to NULL, the description will be removed.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.4 |
h3cDot11APWorkModeRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.5 |
h3cDot11APTemplateRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.6 |
h3cDot11APNameRepresents the AP name.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.7 |
h3cDot11StatisIntervRepresents the interval of radio statistic.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.8 |
h3cDot11APBroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.9 |
h3cDot11StaIdleTimerIntervRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.10 |
h3cDot11StaKeepAliveTimerIntervRepresents the interval of the keep alive requests sent between
AP and STA.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.11 |
h3cDot11APCirRepresents the committed information rate between AP and AC.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.12 |
h3cDot11APCbsRepresents the committed burst size between AP and AC.rw Integer32 UNITS "Bytes" .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.13 |
h3cDot11APPriorityLevelThis object represents the connection priority for the AP.
If the connection priority is 7, the AC is considered as the
primary AC for the AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.14 |
h3cDot11APElementIDThis object represents the AP element ID.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.15 |
h3cDot11APDevDetectEnableRepresents whether device detection is enabled or not.
'true' : Device detection is enabled.
'false': Device detection is disabled.
If device detection is enabled, the AP will provide both device
detection and WLAN data services.
By default, the AP only provides WLAN data services. When an AP works
in monitor mode, that is, the value of object h3cDot11APWorkMode is
monitor, device detection can not be enabled with object
h3cDot11APDevDetectEnable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.16 |
h3cDot11APGetIPMethodThis object represents the method how AP gets IP address.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.17 |
h3cDot11StatisIntervModeThis object represents the mode of statics interval.
normal - statics interval value between 10s to 120s
realtime - statics interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.18 |
h3cDot11ApTrapEnabledRepresents whether the trap status is enabled or not.
'true' : Enable the trap status;
'false' : Disable the trap status.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.1.1.19 |
h3cDot11RadioToConfigTableBefore AP connects to AC, administrator will configure radio
parameter to each radio. SEQUENCE OF H3cDot11RadioToConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.3.2 |
h3cDot11RadioToConfigEntryEach entry contains configuration information for each radio. H3cDot11RadioToConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.3.2.1 |
h3cDot11APTemplateNameCfgRepresents the name of AP template. OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.1 |
h3cDot11CfgRadioIDRepresents each radio. H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.2 |
h3cDot11CfgRadioPolicyNameRepresents the name of radio policy.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.3 |
h3cDot11CfgRadioTypeRepresents the radio will work with which 802.11 radio type.rw H3cDot11RadioType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.4 |
h3cDot11CfgChannelRepresents the channel allocation of radio.rw H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.5 |
h3cDot11CfgMaxTxPowerLevelRepresents the maximal transmit power scope for AP.rw H3cDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.6 |
h3cDot11PreambleLenRepresents whether use long or short preamble for 802.11 MAC
frame.
When h3cDot11CfgRadioType is either dot11b or dot11g,
then value for h3cDot11PreambleLen will be valid.
Othwise, the value for it will be invalid.rw H3cDot11PreambleType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.7 |
h3cDot11CfgRadioStatusRepresents the radio admin status whether is enabled
or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.8 |
h3cDot11CfgRdElementIDRepresents the element ID of this radio. It comprises two parts.
The highest 24 bits are AP element ID and the lowest 8 bits are
radio ID.ro Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.9 |
h3cDot11CfgWorkModeRepresents work mode of the radio.rw H3cDot11WorkMode (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.10 |
h3cDot11CfgPwrAttValueRepresents the value of power attenuation.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.11 |
h3cDot11RadioTxArithmeticRepresents the transmission arithmetic of the radio.
The following values are supported:
quality(1) - Consider the quality first during the transmission.
bandwidth(2) - Consider the bandwidth first during the transmission.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.12 |
h3cDot11CfgChannelLockStatRepresents locked status of channel on the radio.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.13 |
h3cDot11CfgPowerLockStatRepresents locked status of power on the radio.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.14 |
h3cDot11CfgLBRdGroupIdRepresents the load balance group ID allocated for the radio.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.15 |
h3cDot11CfgRRMSDRdGroupIdRepresents the RRM self-decisive group ID allocated for the radio.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.16 |
h3cDot11CfgRadioType2Represents the radio will work with which 802.11 radio type.rw H3cDot11RadioType2 (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.17 |
h3cDot11CfgIDSEnableRepresents whether intrusion detection is enabled for this radio.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.18 |
h3cDot11CfgSaEnableRepresents whether spectrum analysis is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.19 |
h3cDot11CfgSaCltRtFFTDataRepresents whether to collect real-time FFT data for this radio.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.20 |
h3cDot11CfgSaBandRepresents which band of channels will be monitored when collection
real-time FFT data is enabled for this radio. Detection of
interference devices and air quality will also be affected. Each band
responds to the following channels.
dot11g (Channels 1-14)
dot11aLower (channels 36-64)
dot11aMiddle (channels 100-140)
dot11aUpper (channels 149-165).rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.2.1.21 |
h3cDot11APServiceSetTableFor each radio, it could configure multiple service policies.
The table describes the relationship between radio and
service policies. SEQUENCE OF H3cDot11APServiceSetEntry .1.3.6.1.4.1.2011.10.2.75.4.3.3 |
h3cDot11APServiceSetEntryEach entry contains service policy information for each
specific radio of AP. H3cDot11APServiceSetEntry .1.3.6.1.4.1.2011.10.2.75.4.3.3.1 |
h3cDot11CfgServicePolicyIDRepresents the ID of each service policy used by the AP. H3cDot11ServicePolicyIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.3.1.1 |
h3cDot11SrvSetRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.3.1.2 |
h3cDot11ServiceSetVlanIdRepresents the Vlan ID of BSS which is generated when service policy
is binded with the Radio.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.3.1.3 |
h3cDot11APSysInfoSetTableThe table of the system information for each AP. SEQUENCE OF H3cDot11APSysInfoSetEntry .1.3.6.1.4.1.2011.10.2.75.4.3.4 |
h3cDot11APSysInfoSetEntryThe system information configuration for each AP. H3cDot11APSysInfoSetEntry .1.3.6.1.4.1.2011.10.2.75.4.3.4.1 |
h3cDot11APSysNetIDRepresents the system Net ID for AP.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.4.1.1 |
h3cDot11APCpuUsageThresholdThe CPU usage threshold for AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.4.1.2 |
h3cDot11APMemUsageThresholdThe memory usage threshold for AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.4.1.3 |
h3cDot11APLimitTableFor each connected APs, administrator could configure a series of
limits. This table describes the limit information for AP(s). SEQUENCE OF H3cDot11APLimitEntry .1.3.6.1.4.1.2011.10.2.75.4.3.5 |
h3cDot11APLimitEntryEach entry contains the limit information for each AP. H3cDot11APLimitEntry .1.3.6.1.4.1.2011.10.2.75.4.3.5.1 |
h3cDot11APSsidNumLimitRepresents the upper limit of service template binded
with this AP. All radios of AP share this limit.
Default value 0 : There is no upper limit of service template
binded with this AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.5.1.1 |
h3cDot11APUserCntLimitRepresents the upper limit of user which has access to this AP.
All BSSs binded with AP share this limit.
Default value 0 : There is no upper limit of user which has access
to this AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.5.1.2 |
h3cDot11APUserThresholdRepresents the threshold of user which has access to this
AP. All BSSs binded with AP share this limit. If the user counter
is overflow, the trap will be sent.
Default value 0 : There is no threshold of user which has access
to this AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.5.1.3 |
h3cDot11APIfSetTableThe table of the interface information for each AP. SEQUENCE OF H3cDot11APIfSetEntry .1.3.6.1.4.1.2011.10.2.75.4.3.6 |
h3cDot11APIfSetEntryThe interface information configuration for each AP. H3cDot11APIfSetEntry .1.3.6.1.4.1.2011.10.2.75.4.3.6.1 |
h3cDot11APSetIfIndexRepresents the index for a interface. Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.6.1.1 |
h3cDot11APIfAliasThis object is an 'alias' name for the interface as specified
by a network manager for AP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.6.1.2 |
h3cDot11APServiceVlanTableFor all the radios on the AP, it could configure multiple service policies.
The table describes the relationship between AP and
service policies. SEQUENCE OF H3cDot11APServiceVlanEntry .1.3.6.1.4.1.2011.10.2.75.4.3.7 |
h3cDot11APServiceVlanEntryEach entry contains service policy information for each AP. H3cDot11APServiceVlanEntry .1.3.6.1.4.1.2011.10.2.75.4.3.7.1 |
h3cDot11APServiceVlanSerialIDThis object represents AP serial id. OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.7.1.1 |
h3cDot11APServiceVlanSPIDThis object represents the ID of each service policy used by the AP. H3cDot11ServicePolicyIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.7.1.2 |
h3cDot11APServiceVlanIdThis object represents the VLAN ID of BSS which is generated when the
service policy is bound to the radio.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.7.1.3 |
h3cDot11APServiceVlanRowStatusThis object represents the status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.7.1.4 |
h3cDot11RadioConfigTableBefore AP connects to AC, administrator will configure radio
parameter to each radio. SEQUENCE OF H3cDot11RadioConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.3.8 |
h3cDot11RadioConfigEntryEach entry contains configuration information for each radio. H3cDot11RadioConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.3.8.1 |
h3cDot11RCAPSerialIDThis object represents the Serial ID of AP. OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.1 |
h3cDot11RCRadioIDThis object represents each radio. H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.2 |
h3cDot11RCRadioTypeThis object represents the radio will work with which 802.11 radio
type.rw H3cDot11RadioType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.3 |
h3cDot11RCChannelThis object represents the channel allocation of radio.rw H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.4 |
h3cDot11RCPreambleLenThis object represents whether use long or short preamble for 802.11
MAC frame.
When h3cDot11CfgRadioType is either dot11b or dot11g,
then value for h3cDot11PreambleLen will be valid.
Otherwise, the value for it will be invalid.rw H3cDot11PreambleType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.5 |
h3cDot11RCPwrAttValueThis object represents the value of power attenuation.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.6 |
h3cDot11RCApPowerLevelRepresents the maximal transmit power scope for AP.rw H3cDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.7 |
h3cDot11RCDynamicChlStateEnable/Disable dynamic channel selection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.8 |
h3cDot11RCDynamicPowerStateEnable/Disable dynamic power selection for the band.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.9 |
h3cDot11RCRadioStatusRepresents the radio admin status whether is enabled
or disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.10 |
h3cDot11RCRadioRateSet data transmit rates for the radio, in the format of 1,2,5.5...
For 802.11n radios, the format can be MCS X. The data transmit rates
between AP and STA must fall into the configured rates.
(Note: For 802.11n radios, the first value will be treated as a mandatory rate,
and the second value will be treated as a supported rate.
If you configure more than two rates, the configuration cannot take effect.
If you configure only one rate, it is considered as the mandatory rate by default.)rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.11 |
h3cDot11RCPwrAdjustStepLengthPower adjustment step-length in dBm.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.12 |
h3cDot11RCRadioType2This object represents the radio will work with which 802.11 radio
type.rw H3cDot11RadioType2 (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.8.1.13 |
h3cDot11RadioSSIDCfgTableFor each radio, it could configure multiple service policies.
The table describes the relationship between radio and
service policies. SEQUENCE OF H3cDot11RadioSSIDCfgEntry .1.3.6.1.4.1.2011.10.2.75.4.3.9 |
h3cDot11RadioSSIDCfgEntryEach entry contains SSID configuration information for each radio. H3cDot11RadioSSIDCfgEntry .1.3.6.1.4.1.2011.10.2.75.4.3.9.1 |
h3cDot11RadioSSIDSerialIDThis object represents the serial ID of AP. H3cDot11ObjectIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.9.1.1 |
h3cDot11RadioSSIDRadioIDThis object represents each radio. H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.9.1.2 |
h3cDot11RadioSSIDWLANIDThis object represents the WLAN ID of the BSSID. Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.9.1.3 |
h3cDot11RadioSSIDIndexThis object represents the ID of each service policy used by the
radio.rw H3cDot11ServicePolicyIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.3.9.1.4 |
h3cDot11RadioBSSIDAs MAC address format, it is used to identify BSS.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.9.1.5 |
h3cDot11RadioSSIDRowStatusRowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.9.1.6 |
h3cDot11APSerialIDTableThe table will provide the general information about APs. SEQUENCE OF H3cDot11APSerialIDEntry .1.3.6.1.4.1.2011.10.2.75.4.3.10 |
h3cDot11APSerialIDEntryEach entry contains the general information of an AP. H3cDot11APSerialIDEntry .1.3.6.1.4.1.2011.10.2.75.4.3.10.1 |
h3cDot11SIDAPSerialIDRepresents AP serial id. OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.1 |
h3cDot11SIDAPWorkModeRepresents what work mode for AP.
The following values are supported:
normal - AP will supply WLAN service.
monitor - AP will be a monitor to find attack.
hybrid - AP will supply WLAN service and Device detection is
enabled.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.2 |
h3cDot11SIDAPGetIPMethodThis object represents the method how AP gets IP address.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.3 |
h3cDot11SIDAPTemplateNameRepresents the name of AP template.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.4 |
h3cDot11SIDModelAliasRepresents the alias of AP model name.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.5 |
h3cDot11SIDAPDescriptionThis attribute will give more information about AP.
Administrator could suggest the location, owner or
other information for each AP.
If the value is set to NULL, the description will be removed.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.6 |
h3cDot11SIDRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.7 |
h3cDot11SIDAPNameRepresents the AP name.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.8 |
h3cDot11SIDStatisIntervRepresents the interval of radio statistic.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.9 |
h3cDot11SIDAPBroadcastProbeReplyRepresents enable the AP to reply broadcast probe or not.
'true' : The AP to reply broadcast probe is enabled.
'false': The AP to reply broadcast probe is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.10 |
h3cDot11SIDAPStaIdleTimerIntervRepresents the interval for which the link between AP and STA
( power-save or awake ) can be idle.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.11 |
h3cDot11SIDStaKeepAliveTimerIntervRepresents the interval of the keep alive requests sent between
AP and STA.rw Integer32 UNITS "second" .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.12 |
h3cDot11SIDAPCirRepresents the committed information rate between AP and AC.rw Integer32 UNITS "Kbps" .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.13 |
h3cDot11SIDAPCbsRepresents the committed burst size between AP and AC.rw Integer32 UNITS "Bytes" .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.14 |
h3cDot11SIDAPPriorityLevelThis object represents the connection priority for the AP.
If the connection priority is 7, the AC is considered as the
primary AC for the AP.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.15 |
h3cDot11SIDAPElementIDThis object represents the AP element ID.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.16 |
h3cDot11SIDAPDevDetectEnableRepresents whether device detection is enabled or not.
'true' : Device detection is enabled.
'false': Device detection is disabled.
If device detection is enabled, the AP will provide both device
detection and WLAN data services.
By default, the AP only provides WLAN data services. When an AP works
in monitor mode, that is, the value of object h3cDot11APWorkMode is
monitor, device detection can not be enabled with object
h3cDot11SIDAPDevDetectEnable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.17 |
h3cDot11SIDAPStatisIntervModeThis object represents the mode of statics interval.
normal - statics interval value between 10s to 120s
realtime - statics interval value between 2s to 5srw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.3.10.1.18 |
h3cDot11APSTVlanTableFor each service policy, it could be bind to several VLANs.
The table describes the relationship between VLAN and
service policies. SEQUENCE OF H3cDot11APSTVlanEntry .1.3.6.1.4.1.2011.10.2.75.4.3.11 |
h3cDot11APSTVlanEntryEach entry contains VLAN and service policy information for each
specific radio of AP. H3cDot11APSTVlanEntry .1.3.6.1.4.1.2011.10.2.75.4.3.11.1 |
h3cDot11CfgSTVLANIDRepresents the VLAN that current Service Policy have bind to.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.3.11.1.1 |
h3cDot11CfgSTNASPortIDRepresents the NAS Port ID of current Service Policy for each
specific radio of AP.ro OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.3.11.1.2 |
h3cDot11CfgServiceSetRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.3.11.1.3 |
h3cDot11RadioIntfConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.4 |
h3cDot11RadioIntfConfigTableThe table defines the parameters for radio in AP, as per
radio. SEQUENCE OF H3cDot11RadioIntfConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.4.1 |
h3cDot11RadioIntfConfigEntryEach entry contains information of each radio in AP. H3cDot11RadioIntfConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.4.1.1 |
h3cDot11RadioIfIdxRepresents the Radio IfIndex of radio in AP. Integer32 .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.1 |
h3cDot11RadioCfgBeaconIntvlRepresents the interval for Beacon management frame.rw Integer32 UNITS "TU" .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.2 |
h3cDot11RadioCfgDtimIntvlRepresents the number of beacon intervals that shall elapse
between transmission of Beacons frames containing a Traffic
Indication Map (TIM) element whose DTIM Count field is 0.
This value is transmitted in the Delivery TIM (DTIM) Period
field of Beacon frames.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.3 |
h3cDot11RadioCfgRtsThresholdRepresents the current minimum size,in octets,of the MAC
protocol data unit (MPDU), below which a Request to send/Clear
to send (RTS/CTS) handshake shall not be performed.rw Integer32 UNITS "Byte" .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.4 |
h3cDot11RadioCfgFragThresholdRepresents the current maximum size, in octets, of the MPDU that
may be delivered to the PHY. A MSDU shall be broken into
fragments if its size exceeds the value of this attribute after
adding MAC headers and trailers.rw Integer32 UNITS "Byte" .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.5 |
h3cDot11RadioCfgShtRetryThldRepresents the maximum number of transmission attempts of a
frame, the length of which is less than or equal to
h3cDot11RadioRTSThreshold, that shall be made before a failure
condition is indicated.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.6 |
h3cDot11RadioCfglongRtrThldRepresents the maximum number of transmission attempts of a
frame, the length of which is longer than
h3cDot11RadioRTSThreshold, that shall be made before a
failure condition is indicated.rw Integer32 .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.7 |
h3cDot11RadioCfgMaxRxLifetimeRepresents the elapsed time. After the time specified by
h3cDot11RadioCfgMaxRxLifetime, the further attempts to reassemble
the MSDU shall be terminated.rw Unsigned32 UNITS "millisecond" .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.8 |
h3cDot11RadioCfgTypeRepresents the radio will work with which 802.11 radio type.rw H3cDot11RadioType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.9 |
h3cDot11RadioCfgChannelRepresents the channel allocation of radio.rw H3cDot11ChannelScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.10 |
h3cDot11RadioCfgMaxTxPwrLvlRepresents the maximal transmit power scope for AP.rw H3cDot11TxPwrLevelScopeType UNITS "dbm" .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.11 |
h3cDot11RadioCfgPreambleLenRepresents whether use long or short preamble for 802.11 MAC
frame.rw H3cDot11PreambleType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.12 |
h3cDot11RadioCfgWorkModeRepresents work mode of the radio.rw H3cDot11WorkMode (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.13 |
h3cDot11RadioCfgOnly11gEnableRepresents whether enable only 802.11g radio mode or not.
'true' : Only 802.11g radio mode is enabled.
'false': Only 802.11g radio mode is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.14 |
h3cDot11RadioCfgType2Represents the radio will work with which 802.11 radio type.rw H3cDot11RadioType2 (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.4.1.1.15 |
h3cDot11RadioIntfBindTableThe table defines the binding information for each radio in AP. SEQUENCE OF H3cDot11RadioIntfBindEntry .1.3.6.1.4.1.2011.10.2.75.4.4.2 |
h3cDot11RadioIntfBindEntryEach entry contains the radio interface binding information
in AP. H3cDot11RadioIntfBindEntry .1.3.6.1.4.1.2011.10.2.75.4.4.2.1 |
h3cDot11RadioIntfBindSvcPlcyIDRepresents the ID of each service policy. H3cDot11ServicePolicyIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.4.2.1.1 |
h3cDot11RadioIntfBindIfIdxRepresents the Ifindex of interface which is binded to
the radio.rw Unsigned32 .1.3.6.1.4.1.2011.10.2.75.4.4.2.1.2 |
h3cDot11RadioIntfBindRowStatusThe status of this table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.4.2.1.3 |
h3cDot11DataRateConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.5 |
h3cDot11DataRateConfigTableTable will provide data rate configuration for a specific radio type. SEQUENCE OF H3cDot11DataRateConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.5.1 |
h3cDot11DataRateConfigEntryEach entry of the table will provide data rate configuration for a
specific radio type. H3cDot11DataRateConfigEntry .1.3.6.1.4.1.2011.10.2.75.4.5.1.1 |
h3cDot11RadioTypeIDRepresents the radio type. H3cDot11RadioType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.5.1.1.1 |
h3cDot11SupportedRateSetRepresents the supported rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.5.1.1.2 |
h3cDot11MandatoryRateSetRepresents the mandatory rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.5.1.1.3 |
h3cDot11DisabledRateSetRepresents the disabled rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.5.1.1.4 |
h3cDot11SmartRateSetRepresents the rate set of a particular radio type.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.5.1.1.5 |
h3cDot11InterfaceConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.6 |
h3cDot11WlanEssIfTableThis table is used to configure WLAN ESS interface. SEQUENCE OF H3cDot11WlanEssIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.1 |
h3cDot11WlanEssIfEntryEach entry contains the WLAN ESS interface configuration. H3cDot11WlanEssIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.1.1 |
h3cDot11WlanEssIfNumberThis node represents the WLAN ESS interface number. Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.1.1.1 |
h3cDot11WlanEssIfIndexThis node represents the ifIndex of WLAN-ESS interface.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.1.1.2 |
h3cDot11WlanEssRowStatusThis node represents the WLAN ESS interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.6.1.1.3 |
h3cDot11WlanBssIfTableThis table is used to configure WLAN BSS interface. SEQUENCE OF H3cDot11WlanBssIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.2 |
h3cDot11WlanBssIfEntryEach entry contains the WLAN BSS interface configuration. H3cDot11WlanBssIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.2.1 |
h3cDot11WlanBssIfNumberThis node represents the WLAN BSS interface number. Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.2.1.1 |
h3cDot11WlanBssIfIndexThis node represents the ifIndex of WLAN-BSS interface.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.2.1.2 |
h3cDot11WlanBssRowStatusThis node represents the WLAN BSS interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.6.2.1.3 |
h3cDot11WLANEthernetIfTableThis table is used to configure WLAN Ethernet interface. SEQUENCE OF H3cDot11WLANEthernetIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.3 |
h3cDot11WLANEthernetIfEntryEach entry contains the WLAN Ethernet interface configuration. H3cDot11WLANEthernetIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.3.1 |
h3cDot11WlanEthernetIfNumberThis node represents the WLAN Ethernet interface number. Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.3.1.1 |
h3cDot11WLANEthernetIfIndexThis node represents the ifIndex of WLAN-Ethernet interface.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.3.1.2 |
h3cDot11WlanEthernetRowStatusThis node represents the Wlan Ethernet interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.6.3.1.3 |
h3cDot11PortSecurityTableThis table defines the WLAN security status for ESS, BSS, mesh and
WLAN-Ethernet interface which binding the crypto service-template.
Otherwise, when binding the clear service-template,
h3cPortSecurityTables should be used to configure port security. SEQUENCE OF H3cDot11PortSecurityEntry .1.3.6.1.4.1.2011.10.2.75.4.6.4 |
h3cDot11PortSecurityEntryThere is a row in this table for each ESS, BSS and WLAN-Ethernet
interface.It is indexed using the object ifIndex in RFC1213-MIB. H3cDot11PortSecurityEntry .1.3.6.1.4.1.2011.10.2.75.4.6.4.1 |
h3cDot11PortSecurityModeDetermines the security modes of the WLAN port.
noRestrictions(1) The default value,no any security mode is set.
userLoginSecureExt(2) Access to the port is denied until the port
client is authorized (by 802.1X).
psk(3) Access to the port is denied until the port client is
authorized (by 802.1X key negotiation).
macAddressAndPsk(4) The MAC address is first authenticated and only if
this succeeds does the psk then attempt user authentication.
userLoginSecureExtOrPsk(5) This selects both the userLoginSecureExt and
psk modes together such that either is allowed to authorized access.
Which mode works for client depends on the client's choice.
ext(6) Access to the port is denied until the port client is
authenticated (by ext).rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.6.4.1.1 |
h3cDot11SecurityUserLoginTxKeyTypeThis indicates the key type in the 802.1X EAPOL_Key packet.
userLoginTxKeyTypeNone(1) This means the key type is not set yet.
userLoginTxKeyTypeDot11Key(2) This selects the 802.11 key type.
userLoginTxKeyTypeRsaRC4Key(3) This selects the RC4 key for RSA RC4
session encryption.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.6.4.1.2 |
h3cDot11SecurityPskKeyModeThis is the password input mode. When input as pskKeyModePassPhrase,
h3cDot11SecurePskKeyString must be 8 to 63 characters; when input as
pskKeyModeRawKey, h3cDot11SecurePskKeyString must be 64 characters and
each character must be '0'-'9', 'a'-'f' and 'A'-'F'.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.6.4.1.3 |
h3cDot11SecurityPskKeyStringThis is the password string used for psk authentication.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.6.4.1.4 |
h3cDot11WlanMeshIfTableThis table is used to configure WLAN mesh interface. SEQUENCE OF H3cDot11WlanMeshIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.5 |
h3cDot11WlanMeshIfEntryEach entry contains the WLAN mesh interface configuration. H3cDot11WlanMeshIfEntry .1.3.6.1.4.1.2011.10.2.75.4.6.5.1 |
h3cDot11WlanMeshIfNumberThis node represents the WLAN mesh interface number. Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.5.1.1 |
h3cDot11WlanMeshIfIndexThis node represents the index of WLAN mesh interface.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.6.5.1.2 |
h3cDot11WlanMeshRowStatusThis node represents the WLAN mesh interface row status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.6.5.1.3 |
h3cDot11ACBackupGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.7 |
h3cDot11BackupACAdrssIPThis object represents the backup AC IP address.
If the backup AC IP address is not configured,
the object value is 0.0.0.0.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.2011.10.2.75.4.7.1 |
h3cDot11BackupACAdrssIPv6This object represents the backup AC IPv6 address.
If the backup AC IPv6 address is not configured,
the object value is 0::0.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.2011.10.2.75.4.7.2 |
h3cDot11RadioElementConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.8 |
h3cDot11nRadioCfgTableThis table is used to configure dot11n on the radio. SEQUENCE OF H3cDot11nRadioCfgEntry .1.3.6.1.4.1.2011.10.2.75.4.8.1 |
h3cDot11nRadioCfgEntryThis entry contains the dot11n configuration on the radio. H3cDot11nRadioCfgEntry .1.3.6.1.4.1.2011.10.2.75.4.8.1.1 |
h3cDot11nRadioCfgIndexRepresents index of the radio. H3cDot11RadioElementIndex (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.8.1.1.1 |
h3cDot11nAMpduEnableEnable the function of A-MPDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.1.1.2 |
h3cDot11nAMsduEnableEnable the function of A-MSDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.1.1.3 |
h3cDot11nClientDot11nOnlyOnly permit clients of 11n mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.1.1.4 |
h3cDot11nChanelBandSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.8.1.1.5 |
h3cDot11nShortGiEnableThe function of Short GI.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.1.1.6 |
h3cDot11RadioWDSTableThis table is used to configure WDS on the radio. SEQUENCE OF H3cDot11RadioWDSEntry .1.3.6.1.4.1.2011.10.2.75.4.8.2 |
h3cDot11RadioWDSEntryEach entry contains the WDS configuration on the radio. H3cDot11RadioWDSEntry .1.3.6.1.4.1.2011.10.2.75.4.8.2.1 |
h3cDot11RadioWDSIndexRepresents the element index of radio. H3cDot11RadioElementIndex (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.8.2.1.1 |
h3cDot11RadioWDSModeRepresents enable the WDS mode or not.
nowds: The WDS mode is disabled.
wds : The WDS mode is enabledrw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.8.2.1.2 |
h3cDot11RadioWDSNetWorkIDRepresents the mesh ID of WDS.rw OCTET STRING .1.3.6.1.4.1.2011.10.2.75.4.8.2.1.3 |
h3cDot11WDSSecPskKeyModeRepresents the PSK mode of WDS.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.8.2.1.4 |
h3cDot11WDSSecPskKeyStringRepresents the PSK value of WDS.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.2.1.5 |
h3cDot11nRadioCfg2TableThis table is used to configure dot11n on the radio. SEQUENCE OF H3cDot11nRadioCfg2Entry .1.3.6.1.4.1.2011.10.2.75.4.8.3 |
h3cDot11nRadioCfg2EntryThis entry contains the dot11n configuration on the radio. H3cDot11nRadioCfg2Entry .1.3.6.1.4.1.2011.10.2.75.4.8.3.1 |
h3cDot11nRadioCfg2APIDIndexRepresents index of the AP. H3cDot11ObjectIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.8.3.1.1 |
h3cDot11nRadioCfg2RadioIDIndexRepresents index of the radio. H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.8.3.1.2 |
h3cDot11nRadioCfg2AMpduEnableEnable the function of A-MPDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.3.1.3 |
h3cDot11nRadioCfg2AMsduEnableEnable the function of A-MSDU.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.3.1.4 |
h3cDot11nRadioCfg2ClientDot11nOnlyOnly permit clients of 11n mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.3.1.5 |
h3cDot11nRadioCfg2ChannelBandSpecify the bandwidth mode.rw Enumeration .1.3.6.1.4.1.2011.10.2.75.4.8.3.1.6 |
h3cDot11nRadioCfg2ShortGiEnableEnable the function of Short GI.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.10.2.75.4.8.3.1.7 |
h3cDot11CfgNotifyGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.9 |
h3cDot11CfgNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.9.0 |
h3cDot11CfgCipherChangeThis notification is sent when cipher type of corresponding service
template is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.4.9.0.1 |
h3cDot11CfgPSKChangeThis notification is sent when pre-shared key of corresponding
service template is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.4.9.0.2 |
h3cDot11SSIDWepIDConflictTrapThis notification will be sent when the same wep ID is configured
on two service policies. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.10.2.75.4.9.0.3 |
h3cDot11CfgTrapVarObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.10.2.75.4.9.1 |
h3cDot11PreConflictTemplateNumRepresents previous service policy ID when radio bind service policy
and current service policy conflict with previous service policy
in cipher configuration.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.9.1.1 |
h3cDot11CurrConflictTemplateNumRepresents current service policy ID when radio bind service policy
and current service policy conflict with previous service policy
in cipher configuration.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.9.1.2 |
h3cDot11ConflictCipherIdxRepresents wep ID that conflicted with.ro Integer32 .1.3.6.1.4.1.2011.10.2.75.4.9.1.3 |
h3cDot11ConfigureAPIDRepresents which AP is configured.ro H3cDot11ObjectIDType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.9.1.4 |
h3cDot11ConfigureRadioIDRepresents which radio in AP is configured.ro H3cDot11RadioScopeType (H3C-DOT11-REF-MIB) .1.3.6.1.4.1.2011.10.2.75.4.9.1.5 |