ExaltComProducts
AI MIB Summary
The ExaltComProducts MIB module facilitates the monitoring and management of ExaltCom hardware appliances, specifically exposing operational metrics such as interface status, traffic counters, system resource utilization, and device health indicators via SNMP.
Exalt devices
Main OID:
productsMIB.1.3.6.1.4.1.25651.1
191
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
191 total| Object Name |
|---|
productsMIBExalt devices MODULE-IDENTITY .1.3.6.1.4.1.25651.1 |
productsMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.1 |
productsMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2 |
radioInfoCommon Radio Information to all Exalt devices. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.1 |
modelNameA descriptive name for the Radio. See Web, Radio Information, Model Name.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.1 |
partNumberThe Part Number of the Radio. See Web, Radio Information, Part Number.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.2 |
serialNumberThe Radio Serial Number. See Web, Radio Inforamtion, Serial Number.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.3 |
interfaceTypeThe Interfaces available on this radio. Ethernet, T1/E1, etc. See Web, Radio Information, Interface Type.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.4 |
firmwareVersionThe Radio Firmware Version. See Web, Radio Information, Firmware Version.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.5 |
bootVersionThe Radio Boot Code Version. See Web, Radio Information, Boot Version.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.6 |
rdkDbVerThe Device RDK Database Version. See Web, Radio Information, RDK Database Version.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.11 |
txFreqRangeThe Radio Tx Frequency Range. FDD radios have a Tx and Rx frequency range. See Web, Radio Information, RF Transmit range. TDD radios have one frequency range. See Web, Radio Information, RF Frequency Band.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.12 |
rxFreqRangeThe Radio Rx Frequency Range. FDD radios have a Tx and Rx frequency range. See Web, Radio Information, RF Receive range. TDD radios have one frequency range. See Web, Radio Information, RF Frequency Band.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.13 |
rfFreqBandThe Device Frequency Band (Range). TDD radios have N/A value in this field. FDD radios have TX High or TX Low depending on used diplexer and Transmit frequency. See Web, Radio Information, Tx Band.ro DisplayString .1.3.6.1.4.1.25651.1.2.1.14 |
hwIdThe Device Hardware ID number. See Web, Radio Information, Hardware ID numberro DisplayString .1.3.6.1.4.1.25651.1.2.1.15 |
modelNumberThe Model Number of the Radio. See Web, Radio Information, Model Numberro DisplayString .1.3.6.1.4.1.25651.1.2.1.16 |
licenseFeaturesThe list of the features enabled by License Keyro DisplayString .1.3.6.1.4.1.25651.1.2.1.17 |
radioAdminRadio Administration parameters. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.2 |
sysDateThe Radio System Date, MM/DD/YYYY. See Web, Administration, Settings, Date. To make permanent, write save to commitAdminSettings after change. After commit, SNMP restarts and will be down for 30 seconds.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.1 |
sysTimeThe Radio System Time, HH:MM:SS, as 24 hours. See Web, Administration, Settings, Time. To make permanent, write save to commitAdminSettings after change. After commit, SNMP restarts and will be down for 30 seconds.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.2 |
radioName OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.2.3 |
rnLocalThe user specifiable Radio Name for this radio. See Web, Administration, Settings, Radio Name. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.3.1 |
rnRemoteThe Radio Name of the Radio at the far end of this RF Link. Can only be set at that radio. See Web, Administration, Settings, Radio Name.ro DisplayString .1.3.6.1.4.1.25651.1.2.2.3.2 |
linkNameThe user specifiable Link Name for this radio. See Web, Administration, Settings, Link Name. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.4 |
linkSecKeyThe Link Security Key must match on both ends of an RF Link for traffic to pass. See Web, Administration, Settings, Link Security Key. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.5 |
adminPasswordThe password for admin login to Web/CLI. See Web, Administration, Settings, Admin Password. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.6 |
userPasswordThe password for user login to Web/CLI. See Web, Administration, Settings, User Password. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.7 |
ipAddress OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.2.8 |
ipLocalThe IP address of local radio. This IP address is used to manage radio. See Web, Administration, Settings, IP Address. To make permanent, write save to commitAdminSettings after change.rw IpAddress .1.3.6.1.4.1.25651.1.2.2.8.1 |
ipRemoteThe IP address of the remote Radio. This IP address is used to manage Remote radio. Can only be set at that radio. See Web, Administration, Settings, IP Address.ro IpAddress .1.3.6.1.4.1.25651.1.2.2.8.2 |
subnetMaskThe Subnet Mask for IP address of local radio. See Web, Administration, Settings, IP Mask. To make permanent, write save to commitAdminSettings after change.rw IpAddress .1.3.6.1.4.1.25651.1.2.2.9 |
ipAddressNetmaskThe IP address and Subnet Mask of local radio. ie 10.0.0.1/24. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.10 |
defaultGatewayThe Default Gateway for local radio port. See Web, Administration, Settings, Default Gateway. To make permanent, write save to commitAdminSettings after change.rw IpAddress .1.3.6.1.4.1.25651.1.2.2.11 |
aesEnableThe AES enable(0)/disable(1). AES (Advance Encryption Standard) can be implemented to provide additional data security for the wireless link. This function requires an upgrade license key (purchased separately). See Web, Administration, Settings, AES Settings, Enable AES. To make permanent, write save to commitAdminSettings after change.rw Enumeration .1.3.6.1.4.1.25651.1.2.2.12 |
aesKeyThe symmetric AES key for encrypt/decrypt payload data. Different bitlength encryption license keys (for example, 128-bit and 256-bit) are available, depending on model type and license type. AES Key should match both on local radio and far end radio. See Web, Administration, Settings, AES Settings, AES Key. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.13 |
licKeyThe license key which defines radio features and capabilities. See Web, Administration, Settings, License Key. To make permanent, write save to commitAdminSettings after change.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.14 |
snmpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.2.17 |
trapIpaddr1The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.rw IpAddress .1.3.6.1.4.1.25651.1.2.2.17.1 |
trapIpaddrEnable1Enable/Disable trap ip address.ro EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.2 |
trapIpaddr2The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.rw IpAddress .1.3.6.1.4.1.25651.1.2.2.17.3 |
trapIpaddrEnable2Enable/Disable trap ip address.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.4 |
trapIpaddr3The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.rw IpAddress .1.3.6.1.4.1.25651.1.2.2.17.5 |
trapIpaddrEnable3Enable/Disable trap ip address.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.6 |
trapIpaddr4The IP address to which the SNMP traps are directed. See Web, Administration, SNMP, Traps, Trap Destination IP Address.rw IpAddress .1.3.6.1.4.1.25651.1.2.2.17.7 |
trapIpaddrEnable4Enable/Disable trap ip address.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.8 |
trapAuthAuthentication trap enable(1)/disable(0). This is an SNMP standard trap when password information for SNMP is incorrect. See Web, Administration, SNMP, Traps, Authentication Trap.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.9 |
trapRebootReboot trap enable(0)/disable(1). This trap is sent after any radio reboot to inform the manager of the reboot status. See Web, Administration, SNMP, Traps, Radio Reboot Trap.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.10 |
trapLocLinkStatLocal Link Status trap enable(0)/disable(1). This trap is sent when Link is in errored state (equivalent to the Link LED). See Web, Administration, SNMP, Traps, Local Link Status Trap.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.11 |
trapLocAlarmStatLocal Alarm Status trap enable(0)/disable(1). This trap is sent when local radio Status is in errored state (equivalent to the Status LED). See Web, Administration, SNMP, Traps, Local Radio Status Trap.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.12 |
trapRemAlarmStatRemote Alarm Status trap enable(0)/disable(1). This trap is sent when remote radio Status is in errored state (equivalent to the Status LED). See Web, Administration, SNMP, Traps, Remote Radio Status Trap.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.13 |
trapLocTempStatLocal Temperature Status trap enable(0)/disable(1). This trap is sent when the internal temperature reaches the warning point. See Web, Administration, SNMP, Traps, Temperature Status Trap.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.14 |
trapv1EnableSNMPv1 Traps enable(0)/disable(1). Enables traps for SNMP protocol version 1. See Web, Administration, SNMP, Traps, Enable SNMPv1 Traps.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.15 |
trapv2cEnableSNMPv2c Traps enable(0)/disable(1). Enables traps for SNMP protocol version 2c. See Web, Administration, SNMP, Traps, Enable SNMPv2c Traps.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.16 |
trapv3EnableSNMPv3 Traps enable(0)/disable(1). Enables traps for SNMP protocol version 3. See Web, Administration, SNMP, Traps, Enable SNMPv3 Traps.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.17 |
trapLocRslStatLocal RSL Status trap enable(0)/disable(1). This trap is sent when the local RSL drops below the value set in the RSL Threshold Value (dBm) field. See Web, Administration, SNMP, Traps, Local RSL Status Trap.rw EnableStatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.17.18 |
trapLocRslThresholdLocal RSL Threshold. Exalt recommends that this trap be set to a value 5dBm or 10dBm above the threshold as a warning that the system has faded and may be approaching an outage. See Web, Administration, SNMP, Traps, Threshold Value.rw INTEGER .1.3.6.1.4.1.25651.1.2.2.17.19 |
commitSnmpSettingsOption strings to be written are: save, clear, correspondingly saving changes to configuration to the persistent storage or clearing unsaved changes.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.17.1000 |
ntpNTP and Time zone configuration. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.2.18 |
ntpClientEnablethis mib to enable/disable the NTP client in the radio. 0 - disable NTP client. 1 - enable with 1 NTP server. 2 - enable with 2 NTP servers. 3 - enable with 3 NTP servers. 4 - enable with 4 NTP servers.rw NtpClientEnableT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.18.1 |
ntpServer1IpAddrIP address for the first NTP server in xxx.xxx.xxx.xxx formatrw DisplayString .1.3.6.1.4.1.25651.1.2.2.18.2 |
ntpServer2IpAddrIP address for the second NTP server in xxx.xxx.xxx.xxx formatrw DisplayString .1.3.6.1.4.1.25651.1.2.2.18.3 |
ntpServer3IpAddrIP address for the third NTP server in xxx.xxx.xxx.xxx formatrw DisplayString .1.3.6.1.4.1.25651.1.2.2.18.4 |
ntpServer4IpAddrIP address for the forth NTP server in xxx.xxx.xxx.xxx formatrw DisplayString .1.3.6.1.4.1.25651.1.2.2.18.5 |
ntpTimeZoneSelectTime Zone selection. 0 - (GMT-11:00) Samoa 1 - (GMT-10.00) Hawaii 2 - (GMT-09:00) Alaska 3 - (GMT-08:00) Pacific Time 4 - (GMT-07:00) Arizona 5 - (GMT-07:00) Montain Time 6 - (GMT-06:00) Central Time 7 - (GMT-05:00) Eastern Time 8 - (GMT-05:00) Indiana (East) 9 - (GMT-04:00) Atlantic Time (Canada) 10- (GMT) Coordinated Universal Time 11- (GMT) London 12- (GMT+01:00) Berlin 13- (GMT+01:00) Belgrade 14- (GMT+01:00) Paris 15- (GMT+02:00) Cairo 16- (GMT+02:00) Helsinki 17- (GMT+03:00) Baghdad 18- (GMT+03:00) Moscow 19- (GMT+03:30) Tehran 20- (GMT+04:30) Kabul 21- (GMT+05:00) Karachi 22- (GMT+07:00) Bangkok 23- (GMT+08:00) Shanghai 24- (GMT+08:00) Taipei 25- (GMT+09:00) Tokyo 26- (GMT+09:00) Seoul 27- (GMT+10:00) Sydney 28- (GMT+10:00) Vladivostokrw TimeZoneT (ExaltComm) .1.3.6.1.4.1.25651.1.2.2.18.6 |
commitNtpSettingsThis command allows saving or clear the NTP and Tome Zone configuration. If the save includes the change of time zone, the radio will automatically reboot to take effect the newly selected time zone. Option strings to be written are: save, clear, correspondingly saving changes to configuration to the persistent storage or clearing unsaved changes.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.18.1000 |
commitAdminSettingsThe Commit Administration settings command. Valid values: 'save', 'clear'. Configuration changes via SNMP do not take effect until 'save' (Commit) command is sent to this parameter. 'clear' (Cancel) command is used to cancel configuration changes before commit operation. In case of invalid configuration this parameter contains text description of the problem.rw DisplayString .1.3.6.1.4.1.25651.1.2.2.1000 |
radioConfigThe Radio Configuration Section. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.3 |
systemConfigThis is the device specific configuration section. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.3.1 |
commitSystemSettingsThe Commit System Configuration settings command. Valid values: 'save', 'clear'. Configuration changes via SNMP do not take effect until 'save' (Commit) command is sent to this parameter. 'clear' (Cancel) command is used to cancel configuration changes before commit operation. In case of invalid configuration this parameter contains text description of the problem.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.3.1.1000 |
interfaceRadio Interfaces Configuration section. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.3.2 |
te1T1,E1 interfaces Configuration section. Section allows to configure T1/E1 ports on the radio if any. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.3.2.2 |
te1NumChannelsThe Number of T1 or E1 channels supported by the Radio.ro Gauge32 UNITS "channels" .1.3.6.1.4.1.25651.1.2.3.2.2.1 |
te1NumActiveChannelsThe Current number of channels available, based on bandwitdh of the RF link and the license key.ro Gauge32 UNITS "channels" .1.3.6.1.4.1.25651.1.2.3.2.2.2 |
selectT1orE1Select operation mode of T1/E1 interfaces. Either T1(0) or E1(1). See Web, Configuration, Interface, T1/E1, Set To E1/T1 Mode button.rw Enumeration .1.3.6.1.4.1.25651.1.2.3.2.2.3 |
te1InterfacesAttributes for T1 or E1 ports. SEQUENCE OF Te1InterfacesEntry .1.3.6.1.4.1.25651.1.2.3.2.2.4 |
te1InterfaceAn entry in the T1/E1 Attribute table. Te1InterfacesEntry .1.3.6.1.4.1.25651.1.2.3.2.2.4.1 |
te1StatusThe T1/E1 status: enable(1)/disable(0). Parameter allows to enable/disable each individual T1 channel. See Web, Configuration, Interface, T1/E1, Status. To make permanent, write save to commitTe1Settings after change.rw Te1StatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.3.2.2.4.1.1 |
t1LBOThe Line Build Out length range. Valid values (ft): lbo0to133(0), lbo133to266(1), lbo266to399(2), lbo399to533(3), lbo533to655(4). See Web, Configuration, Interface, T1/E1, LBO. To make permanent, write save to commitTe1Settings after change.rw Te1LboT UNITS "feet" .1.3.6.1.4.1.25651.1.2.3.2.2.4.1.2 |
te1AISThe T1/E1 AIS enabled flag: enable(1)/disable(0). If enabled, the radio places an AIS code on the output of the associated interface if and when the link fails or when there is no E1 signal available from the far end to provide the user at the local end. See Web, Configuration, Interface, T1/E1, AIS. To make permanent, write save to commitTe1Settings after change.rw Te1StatusT (ExaltComm) .1.3.6.1.4.1.25651.1.2.3.2.2.4.1.3 |
t1LineCodeThe T1/E1 Line Code type: b8zs(0), ami(1). See Web, Configuration, Interface, T1/E1, AIS, Line Code. To make permanent, write save to commitTe1Settings after change.rw Te1LineCodeT (ExaltComm) .1.3.6.1.4.1.25651.1.2.3.2.2.4.1.4 |
te1LoopBackModeThe Loop Back Mode for a T1/E1 interface. Valid values: disabled(0), ExternalLocal(1), ExternalRemote(2), Internal(3). All loopback configurations control the loop at the Line Interface integrated circuit, which is the device wired directly to the front panel ports. See Web, Configuration, Interface, T1/E1, AIS, Loopback. To make permanent, write save to commitTe1Settings after change.rw Te1LoopBackModeT (ExaltComm) .1.3.6.1.4.1.25651.1.2.3.2.2.4.1.5 |
commitTe1SettingsThe Commit TE1 Configuration settings command. Valid values: 'save', 'clear'. Configuration changes to TE1 ports via SNMP do not take effect until 'save' (Commit) command is sent to this parameter. 'clear' (Cancel) command is used to cancel configuration changes before commit operation. In case of invalid configuration this parameter contains text description of the problem.rw DisplayString .1.3.6.1.4.1.25651.1.2.3.2.2.1000 |
fileManagementThe File Management Section. This section allows to initiate Upload/Download firmware/configuration/logs, perform Firmware activation procedure. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.3.3 |
currentFwFilenameThe file name of the currently running firmware. See Web, Administration, File Management, File Activation, Current File.ro DisplayString .1.3.6.1.4.1.25651.1.2.3.3.1 |
alternateFwFilenameThe file name of the alternate firmware image. See Web, Administration, File Management, File Activation, Alternative File.ro DisplayString .1.3.6.1.4.1.25651.1.2.3.3.2 |
swapFWimageSwap the firmware images and restart radio. To perform swap operation 'swap' command needs to be sent to this parameter. For ExtendAirG2 to perform revert to factory operation 'factory' command needs to be sent. Radio will become unavailable for several minutes.rw DisplayString .1.3.6.1.4.1.25651.1.2.3.3.3 |
fileTransferThe File Transfer Section. This section allows to initiate Upload/Download firmware/configuration/logs over TFTP protocol. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.3.3.4 |
tftpServerIpThe TFTP Server IP address.rw DisplayString .1.3.6.1.4.1.25651.1.2.3.3.4.1 |
uploadFilenameThe name of the file for upload operation. For configuration file uploadFilename should be always 'config.xml'. uploadFilename value should match the file name in TFTP server folder.rw DisplayString .1.3.6.1.4.1.25651.1.2.3.3.4.2 |
transferTypeThe file transfer type. Valid values: - uploadFirmware(0) - uploadConfig(1) - uploadRDD(2) (Valid only for TDD radios) - downloadFirmware(3) - downloadConfig(4) - downloadMIBs(5) - downloadEventLogs(6). The actual operation starts via updating transferStart parameter value.rw FileTransferTypeT (ExaltComm) .1.3.6.1.4.1.25651.1.2.3.3.4.3 |
transferStartTransferStart parameter is used to initiate file transfer operation. Send startTransfer(1) to this parameter.rw FileTransferStartT (ExaltComm) .1.3.6.1.4.1.25651.1.2.3.3.4.4 |
transferStatusThe current file transfer status.ro DisplayString .1.3.6.1.4.1.25651.1.2.3.3.4.5 |
factoryFwFilenameThe file name of the factory firmware image. See Web, Administration, File Management, File Activation, Factory File.ro DisplayString .1.3.6.1.4.1.25651.1.2.3.3.5 |
radioMonitorMonitor Various components. OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2 |
almLocal OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.3 |
locSysAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.3.1 |
locLinkStateThe Link Status Alarm. Possible values: - almNORMAL(0) - Error-free connection (BER<10e-6) - almMINOR(1) - Errorred connection (BER<10e-3) - almMAJOR(2) - No link (BER>10e-3) See Web, Monitor, Alarms, Linkro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.3.1.1 |
locTempAlarmThe Temperature Alarm state. Possible values: - almNORMAL(0) - Normal temprature range - almMINOR(1) - Exceeding normal temprature range See Web, Monitor, Alarms, Temperaturero AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.3.1.2 |
locCurrentTempThe Internal Temperature in Celsius.ro Integer32 UNITS "C" .1.3.6.1.4.1.25651.1.2.4.2.3.1.3 |
locCurrentTempSThe Internal Temperature as a string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.2.3.1.4 |
locLinkSecMismatchThis is link security mismatch alarm. This alarm tells if the Link Security Key is matching or not. Possible values: - almNORMAL(0) - Link Secutiry keys match - almMAJOR(2) - Link Secutiry keys do not matchro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.3.1.9 |
locLinkStateVVertical Link Status Alarm. -<g89><>ro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.3.1.15 |
locLinkStateHHorizontal Link Status Alarm. -<g89><>ro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.3.1.16 |
locEthAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.3.2 |
locTe1Alarms OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.3.3 |
locTe1LinkSummaryThe T1/E1 Link Summary LED color.ro Led4ColorT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.3.3.1 |
locTE1AlarmsThe Local T1/E1 Interface Alarms. SEQUENCE OF Te1Alarms1Entry .1.3.6.1.4.1.25651.1.2.4.2.3.3.2 |
locTe1AlarmsEntryT1/E1 Alarms table Entry. Te1Alarms1Entry .1.3.6.1.4.1.25651.1.2.4.2.3.3.2.1 |
locTe1AlarmThe Alarms state for the Local T1/E1 Channel. Possible values: - almNORMAL(0) - Enabled and connection present - almMAJOR(2) - Enabled and no connection present - almDisable(3) - Disabled and no connection present - almNotAvailable(4) - T1/E1 channel is not available See Web, Monitor, Alarms, T1/E1 Inputro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.3.3.2.1.1 |
almRemote OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.4 |
remSysAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.4.1 |
remLinkStateThe Link Status Alarm for far end radio. Possible values: - almNORMAL(0) - Error-free connection (BER<10e-6) - almMINOR(1) - Errorred connection (BER<10e-3) - almMAJOR(2) - No link (BER>10e-3) - almNotAvailable(4) - Telemetry is down See Web, Monitor, Alarms, Linkro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.4.1.1 |
remTempAlarmThe Temperature Alarm state for far end radio. Possible values: - almNORMAL(0) - Normal temprature range - almMINOR(1) - Exceeding normal temprature range - almNotAvailable(4) - Telemetry is down See Web, Monitor, Alarms, Temperaturero AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.4.1.2 |
remCurrentTempThe Internal Temperature in Celsius for far end radio.ro Integer32 UNITS "C" .1.3.6.1.4.1.25651.1.2.4.2.4.1.3 |
remCurrentTempSThe internal Temperature as a string for far end radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.2.4.1.4 |
remLinkSecMismatchThis is link security mismatch alarm. This alarm tells if the Link Security Key is matching or not. Possible values: - almNORMAL(0) - Link Secutiry keys match - almMAJOR(2) - Link Secutiry keys do not match - almNotAvailable(4) - Telemetry is downro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.4.1.9 |
remLinkStateVVertical Link Status Alarm. -<g89><>ro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.4.1.15 |
remLinkStateHHorizontal Link Status Alarm. -<g89><>ro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.4.1.16 |
remEthAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.4.2 |
remTe1Alarms OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.2.4.3 |
remTe1LinkSummaryThe T1/E1 Link Summary LED color.ro Led4ColorT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.4.3.1 |
remTE1AlarmsThe Remotel T1/E1 Interface Alarms. SEQUENCE OF Te1AlarmsEntry .1.3.6.1.4.1.25651.1.2.4.2.4.3.2 |
remTe1AlarmsEntryT1/E1 Alarms table Entry. Te1AlarmsEntry .1.3.6.1.4.1.25651.1.2.4.2.4.3.2.1 |
remTe1AlarmThe Alarms state for the Local T1/E1 Channel of far end radio. Possible values: - almNORMAL(0) - Enabled and connection present - almMAJOR(2) - Enabled and no connection present - almDisable(3) - Disabled and no connection present - almNotAvailable(4) - Telemetry is down or T1/E1 channel is not available See Web, Monitor, Alarms, T1/E1 Inputro AlarmLevelT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.2.4.3.2.1.1 |
performance OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.3 |
perfLocal OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.3.1 |
locCurrentBERThe Curent Bit-Error Rate as scaled integer for local radio. The BER multiplied by 1,000,000. If the link is operating perfectly, this should indicate zero. See Web, Monitor, Performance, Current BERro Integer32 UNITS "BER * 1000000.0" .1.3.6.1.4.1.25651.1.2.4.3.1.1 |
locCurrentBERstrThe Current Bit-Error Rate as a string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.2 |
locCurrentRSLCurrent RSL is the measurement of the received signal level. When the RSL falls below the threshold specification, the link disconnects and will not reconnect until the RSL is above the threshold specification. See Web, Monitor, Performance, Current RSLro Integer32 UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.1.3 |
locCurrentRSLstrThe Current RSL as a string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.4 |
locErrorDurationThe Error Duration indicates the total number of seconds that occurred where there was at least one bit error since the last time that the radio statistics counter was reset. See Web, Monitor, Performance, Errored Secondsro Integer32 UNITS "Seconds" .1.3.6.1.4.1.25651.1.2.4.3.1.5 |
locErrorDurationStrThe Error Duration as a formatted string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.6 |
locUnavailDurationUnavailable Duration keeps track of every second where the BER equals or exceeds 1x10-3, as well as any seconds where there is a complete loss of radio communication. See Web, Monitor, Performance, Unavailable Secondsro Integer32 UNITS "Seconds" .1.3.6.1.4.1.25651.1.2.4.3.1.7 |
locUnavailDurationStrThe Unavailable Duration as a formatted string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.8 |
locMinRSLThe Minimum RSL indicates the worst (lowest) received signal level that occurred since the last counter reset. See Web, Monitor, Performance, Minimum RSLro Integer32 UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.1.9 |
locMinRSLstrThe Minimum RSL value as a string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.10 |
locMinRSLtimestampThe Minimum RSL Timestamp indicates the date and time when the Minimum RSL occurred. See Web, Monitor, Performance, Minimum RSL Timestampro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.11 |
locMaxRSLThe Maximum RSL indicates the best (highest) RSL that occurred since the last counter reset. See Web, Monitor, Performance, Maximum RSLro Integer32 UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.1.12 |
locMaxRSLstrThe Maximum RSL level As string.ro DisplayString UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.1.13 |
locSampleDurationThe Sample Duration indicates the amount of time passed since the last counter reset. See Web, Monitor, Performance, Time Since Resetro Integer32 UNITS "Seconds" .1.3.6.1.4.1.25651.1.2.4.3.1.14 |
locSampleDurationStrThe Sample Duration value as a formatted string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.15 |
locEthPerfInterfacesPerformance characteristics of local Ethernet interfaces SEQUENCE OF LocEthPerfInterfacesEntry .1.3.6.1.4.1.25651.1.2.4.3.1.16 |
locEthPerfInterfacesEntryAn entry in the Performance characteristics of local Ethernet interfaces table LocEthPerfInterfacesEntry .1.3.6.1.4.1.25651.1.2.4.3.1.16.1 |
locEthUtilizationInInbound ethernet utilization (%). See Web, Analysis, Ethernet Utilization.ro Integer32 .1.3.6.1.4.1.25651.1.2.4.3.1.16.1.1 |
locEthUtilizationOutOutbound ethernet utilization (%). See Web, Analysis, Ethernet Utilization.ro Integer32 .1.3.6.1.4.1.25651.1.2.4.3.1.16.1.2 |
locEthSpeedCurrent Ethernet Speed. See Web, Monitor, Ethernet Performance.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.16.1.3 |
locEthUtilizationWatermarkEnabledEthernet utilization watermark enable(1)/disable(0). See Web, Analysis, Ethernet Utilization, Ethernet Utilization Watermark.rw ExaltEnableT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.17 |
locEthUtilizationWatermarkEthernet utilization watermark level (%). See Web, Analysis, Ethernet Utilization, Watermark level.rw Integer32 .1.3.6.1.4.1.25651.1.2.4.3.1.18 |
locEthUtilizationWatermarkTrapEnabledEthernet utilization watermark trap enable(1)/disable(0). The watermark trap function allows administrators to receive an SNMP trap when watermark conditions are exceeded. See Web, Analysis, Ethernet Utilization, Enable Ethernet Utilization Trap.rw ExaltEnableT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.19 |
locEthUtilizationWatermarkTrapDurationEthernet utilization trap limit in minutes/day (0-1440 minutes). See Web, Analysis, Ethernet Utilization, Send trap if watermark hit duration exceeds.rw Integer32 .1.3.6.1.4.1.25651.1.2.4.3.1.20 |
locMaximumTxModulationThe highest/maximum Tx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx modulation.ro AcmModulationT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.100 |
locActiveTxModulationThe active Tx modulation when ACM is enabled. See Web, Monitor, Performance, Tx modulation.ro AcmModulationT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.101 |
locMinimumTxModulationThe lowest/minimum Tx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx modulation.ro AcmModulationT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.102 |
locMaximumRxModulationThe highest/maximum Rx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx modulation.ro AcmModulationT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.103 |
locActiveRxModulationThe active Rx modulation when ACM is enabled. See Web, Monitor, Performance, Rx modulation.ro AcmModulationT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.104 |
locMinimumRxModulationThe lowest/minimum Rx modulation when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx modulation.ro AcmModulationT (ExaltComm) .1.3.6.1.4.1.25651.1.2.4.3.1.105 |
locMaximumTxEthernetThroughputThe highest/maximum Tx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx Ethernet Throughput.ro INTEGER .1.3.6.1.4.1.25651.1.2.4.3.1.106 |
locActiveTxEthernetThroughputThe active Tx Ethernet throughput in Mbps when ACM is enabled. See Web, Monitor, Performance, Tx Ethernet Throughput.ro INTEGER .1.3.6.1.4.1.25651.1.2.4.3.1.107 |
locMinimumTxEthernetThroughputThe lowest/minimum Tx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Tx Ethernet Throughput.ro INTEGER .1.3.6.1.4.1.25651.1.2.4.3.1.108 |
locMaximumRxEthernetThroughputThe highest/maximum Rx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx Ethernet Throughput.ro INTEGER .1.3.6.1.4.1.25651.1.2.4.3.1.109 |
locActiveRxEthernetThroughputThe active Rx Ethernet throughput in Mbps when ACM is enabled. See Web, Monitor, Performance, Rx Ethernet Throughput.ro INTEGER .1.3.6.1.4.1.25651.1.2.4.3.1.110 |
locMinimumRxEthernetThroughputThe lowest/minimum Rx Ethernet throughput in Mbps when ACM is enabled since the last counter reset. See Web, Monitor, Performance, Rx Ethernet Throughput.ro INTEGER .1.3.6.1.4.1.25651.1.2.4.3.1.111 |
locResetStatsWrite 'reset' to locResetStats to clear the Performance statistics.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.1.1000 |
perfRemote OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.3.2 |
remCurrentBERThe Curent Bit-Error Rate as scaled integer for far end radio. The BER multiplied by 1,000,000. If the link is operating perfectly, this should indicate zero. See Web, Monitor, Performance, Current BERro Integer32 UNITS "BER * 1000000.0" .1.3.6.1.4.1.25651.1.2.4.3.2.1 |
remCurrentBERstrThe Current Bit-Error Rate as a string. Far end radioro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.2 |
remCurrentRSLCurrent RSL is the measurement of the received signal level. When the RSL falls below the threshold specification, the link disconnects and will not reconnect until the RSL is above the threshold specification. See Web, Monitor, Performance, Current RSLro Integer32 UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.2.3 |
remCurrentRSLstrThe Current RSL as a string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.4 |
remErrorDurationThe Error Duration indicates the total number of seconds that occurred where there was at least one bit error since the last time that the radio statistics counter was reset. See Web, Monitor, Performance, Errored Seconds, Remote column.ro Integer32 UNITS "Seconds" .1.3.6.1.4.1.25651.1.2.4.3.2.5 |
remErrorDurationStrThe Error Duration as a formatted string. Far end radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.6 |
remUnavailDurationUnavailable Duration keeps track of every second where the BER equals or exceeds 1x10-3, as well as any seconds where there is a complete loss of radio communication. See Web, Monitor, Performance, Unavailable Secondsro Integer32 UNITS "Seconds" .1.3.6.1.4.1.25651.1.2.4.3.2.7 |
remUnavailDurationStrThe Unavailable Duration as a formatted string. Far end radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.8 |
remMinRSLThe Minimum RSL indicates the worst (lowest) received signal level that occurred since the last counter reset. See Web, Monitor, Performance, Minimum RSL, Remote column.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.2.9 |
remMinRSLstrThe Minimum RSL value as a string. Far end radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.10 |
remMinRSLtimestampThe Minimum RSL Timestamp indicates the date and time when the Minimum RSL occurred. See Web, Monitor, Performance, Minimum RSL Timestamp, Remote column.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.11 |
remMaxRSLThe Maximum RSL indicates the best (highest) RSL that occurred since the last counter reset. See Web, Monitor, Performance, Maximum RSL, Remote column.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.2.12 |
remMaxRSLstrThe Maximum RSL level As string. Far end radio.ro DisplayString UNITS "dBm" .1.3.6.1.4.1.25651.1.2.4.3.2.13 |
remSampleDurationThe Sample Duration indicates the amount of time passed since the last counter reset. See Web, Monitor, Performance, Time Since Reset, Remote column.ro Integer32 UNITS "Seconds" .1.3.6.1.4.1.25651.1.2.4.3.2.14 |
remSampleDurationStrThe Sample Duration value as a formatted string. Far end radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.15 |
remResetStatsWrite 'reset' to remResetStats to clear the Performance statistics.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.25651.1.2.4.3.2.1000 |
userThroughput OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.2.4.5 |
aggregateUserThroughputAggregated User Throughput. For FDD radios this parameter is always equal to fullDuplexEthernetThroughput.ro DisplayString UNITS "MBit/s" .1.3.6.1.4.1.25651.1.2.4.5.1 |
inboundEthernetThroughputInbound Ethernet Throughput. For FDD radios this parameter is always N/A.ro DisplayString UNITS "MBit/s" .1.3.6.1.4.1.25651.1.2.4.5.2 |
outboundEthernetThroughputOutbound Ethernet Throughput. For FDD radios this parameter is always N/A.ro DisplayString UNITS "MBit/s" .1.3.6.1.4.1.25651.1.2.4.5.3 |
fullDuplexEthernetThroughputThe Full Duplex Ethernet Throughput is determined by the combination of settings for Mode and Bandwidth. See Web, Monitor, User Throughput, Full Duplex Ethernet Throughput.ro DisplayString UNITS "MBit/s" .1.3.6.1.4.1.25651.1.2.4.5.4 |
radioRebootReboot the radio device. Send 'reboot' to radioReboot parameter to reboot the radio device.rw DisplayString .1.3.6.1.4.1.25651.1.2.1000 |
productsMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.3 |
productsMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.3.1 |
productsMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.25651.1.3.2 |
productsAllObjectsThis automatically created object group contains all those objects that do not belong to any other OBJECT-GROUP Unknown .1.3.6.1.4.1.25651.1.3.2.1 |