EXCEL-SWITCH-MIB
The MIB module for entities implementing the xxxx protocol.
Main OID:
excel.1.3.6.1.4.1.1751.1.67
473
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
473 total| Object Name |
|---|
lucent OBJECT IDENTIFIER .1.3.6.1.4.1.1751 |
RFC1155-SMI Unknown .1.3.6.1.4.1.1751 |
RFC1213-MIB NOTIFICATION-TYPE .1.3.6.1.4.1.1751 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1 |
excelThe MIB module for entities implementing the xxxx
protocol. MODULE-IDENTITY .1.3.6.1.4.1.1751.1.67 |
excelTraps OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.0 |
excelCardUpTrapThis trap is sent when a card is recognized by the matrix for the
first time. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.1 |
excelCardDownTrapThis trap is sent when a card goes out of service, is removed or
for some reason is no longer recognized by the matrix. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.2 |
excelCardActiveTrapThis trap is sent after a switchover has occured from the
standby to active card. excelDeviceCardSlotIndex will
indicate the slot of the new active card. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.3 |
excelFaultLoggedTrapThis trap is sent when a fault has occurred on a card. The
slot number of the card on which a fault occurred is bound to
the trap. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.4 |
excelRingUpTrapThis trap is sent when an Exnet ring comes up. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.5 |
excelRingDownTrapThis trap is sent when an Exnet ring goes down. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.6 |
excelSystemBusyTrapIf the system is in a Busy Condition, then the matrix EX/CPU
is flooded with messages. All incoming calls will be ignored
until the alarm is cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.7 |
excelSystemBusyWarningTrapSystem Busy Warning state. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.8 |
excelSystemBusyClearedTrapThe System Busy condition on the switch has cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.9 |
excelClockModeChangeTrapThis trap occurs when the clock mode was automatically
switched or reference clock sources have been lost.
The switch will automatically switch the clock mode to the next
available clock source. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.10 |
excelDSPResourceBlockTrapThis trap is sent when a DSP resource Block has occurred. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.11 |
excelDSPFuncNotCfgTrapDSP Resource Function type not configured. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.12 |
excelDSPMgmtInconsistentTrapDSP resource management inconsistent. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.13 |
excelDldTimeoutTrapDownload record timeout. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.14 |
excelRANUnAvailableTrapRecorded announcement requested is no longer available in the
system. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.15 |
excelResourceUtilThreshTrapResource Utilization Threshold Reached. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.16 |
excelCardNotSuppTrapCard type not supported. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.17 |
excelCardDldCorruptTrapCard Download is corrupt NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.18 |
excelCardNotRecTrapCard type not recognized NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.19 |
excelCardCfgResetTrapCard's Configuration has been reset to defaults. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.20 |
excelCardConnMapFailTrapConnection Map Failure. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.21 |
excelCardNoSWTrapSoftware does not have download for card. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.22 |
excelCardNoALawTrapCard does not support A-law encoding format. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.23 |
excelCardRevNotSuppTrapCard revision not supported by system software revision. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.24 |
excelEthernetErrTrapThe switch determines the integrity of the host link by
monitoring host ACKs to Poll messages. If two consecutive
Poll messages are unacknowledged by the host, the switch
resets its Ethernet Receiver and this trap will be sent.
If the error continues even after reset, the problem could
be caused by slow host processing (especially during boot-up).
This can be prevented by increasing the polling interval. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.25 |
excelNoFanTrayTrapNo fan tray installed NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.26 |
excelExnetACommFailTrapExnet Port A - Communication failure NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.27 |
excelExnetBCommFailTrapExnet Port B - Communication failure NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.28 |
excelExnetAFiberFailTrapExnet Port A - Fiber laser failure NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.29 |
excelExnetBFiberFailTrapExnet Port B - Fiber laser failure NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.30 |
excelEXSAPITrapThis EXS Node is not using the extended API. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.31 |
excelEXSConfTSTrapThe available EXS Conferencing timeslot count has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.32 |
excelEXSSCbusMasterChangedTrapThe master of the SCbus that the Excel EXNET Connect
card represented by excelExnetConnectIndex resides on has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.33 |
excelEXSSCbusFailureTrapThe SCbus that the Excel EXNET Connect card represented by
excelExnetConnectIndex resides has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.34 |
excelSS7NetCongestionTrapSS7 Signaling Network traffic has reached congested levels. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.35 |
excelSS7RemISUPUnavailTrapSS7 Remote ISUP unavailable. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.36 |
excelClockSourceLostTrapThe Reference Clock Source has been lost. No host
intervention is needed for this occurance. The switch
will automatically switch the clock mode to the next
available clock source. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.37 |
excelClockSourceLostClearedTrapThe Reference Clock Source has been reestablished
automatically by the switch. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.38 |
excelNoSupportDSPFuncTrapHardware cannot support function type. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.39 |
excelPartialMessageReceivedTrapPartial message received. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.40 |
excelUnackedMsgTrapUnacknowledged Message. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.41 |
excelNodeIDAlreadyExistsTrapNode ID Already Exists. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.42 |
excelInvalidMsgLenTrapInvalid Message Length. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.43 |
excelLogSpanIDExistsTrapLogical span ID already exists on another node. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.44 |
excelNodeUpTrapThis trap is sent when the Agent recognizes a new node in the
system. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.45 |
excelNodeDownTrapThis trap is sent when the Agent has lost connectivity to the
switch. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.46 |
excelSubagentConnectThis trap is sent when the subagent process successfully
connects with the master agent. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.47 |
excelSwitchConnectThis trap is sent when the subagent process successfully
connects to the switch interface process. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.48 |
excelSwitchLossConnectivityThis trap is sent when the subagent process detects a loss of
connectivity with the switch interface process NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.49 |
excelSpanCarrierGroupAlarmThis trap is generated when the switch detects a Carrier Group
Alarm for more then some customer configured time. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.50 |
excelSpanExcessiveSlipsThis trap will occur when the switch detects an abnormally high
number of slips occurring NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.51 |
excelSpanJ1FailureGeneric J1 failure NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.52 |
excelLineCardBusyThis trap will occur when the line card exceeds it's final
traffic threshold level NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.53 |
excelLineCardApproachBusyThis trap will occur when the line card reaches it's initial
traffic threshold level NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.54 |
excelLowMemoryThis trap will occur when memory usage on the line card
exceeds the defined threshold level NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.55 |
excelCardStatusChangeThis trap will occur on any generic card status change NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.56 |
excelLowMemoryClearedThis trap will occur when memory usage on the line card
returns below the defined threshold level NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.57 |
excelGenericEventThis trap will occur when an undefined event is received NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.58 |
excelSubrateSwitchOver NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.59 |
excelSwitchOverInterruptThe D-channel has gone from being In Service to Out Of Service NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.60 |
excelSwitchOverSuccessThe controller switchover was successful. The new D channel is
now the controller NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.61 |
excelSwitchOverFailureThe controller switchover failed. The existing D channel is
still controlling the D channel NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.62 |
excelBackupDiagnosticsInformation Alarm when the state of the D channel changes NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.63 |
excelSCbusMasterChangeThe local bus clock master has changed e.g. If the EXNET Connect
is configured to be the local (SC/MVIP) clock master and
another resource on the local bus is configured to be the
backup clock master and the EXNET Connect is then configured
NOT to be master or fails to drive the clock, the backup
master will take over and drive the clock. This alarm is sent
when the EXNET Connect detects this. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.64 |
excelSCBusFailThis event occurs wheneve a matrix has lost contact with a
remote SS7 card that is controlling CIC's that are located on
that node NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.65 |
excelGeneralSoftwareErrorDefault error message for unexpected errors. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.66 |
excelRearSlotControllerCommunications resources are being currently controlled by the
corresponding rear slot NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.67 |
excelFrontSlotControllerCommunications resources are being currently controlled by the
corresponding front slot NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.68 |
excelConnectNotification NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.69 |
excelRouteTableUpdatedThe active route table has been updated NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.70 |
excelResourceGroupTableUpdatedThe active resource group table has been updated NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.71 |
excelOldRouteTableDeletedA previously active routing table has been deleted NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.73 |
excelRouteTableForcefullyDeletedThe active route tabel was forcefully deleted NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.74 |
excelResourceGroupTableForceDeleteThe active resource group table has been forcefully deleted NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.75 |
excelLoadProblemThis event will occur when a problem occurs during the flash or
RAM loading NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.76 |
excelTFTPFailureThis event will occur when a problem occurs during TFTP
processing NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.77 |
excelPPLEventL3PCICPPL event received from Layer 3 Plus CIC, component ID 15.
The possible event ID's are :
1 Reset confirm indication
8 Remote maintenance block indication
9 Remote maintenance unblock indication
14 ISUP protocol violation
15 Remote hardware group block indication
16 Remote hardware group unblock indication
18 Local maintenance block success
19 Local maintenance unblock success
21 Local circuit maintenance unblocking indication
22 UCIC received
23 No GRS/RSC received
25 OLM received from the network
99 DSP resource allocation failure NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.78 |
excelPPLEventL3PLINKPPL event received from Layer 3 Plus Link, component ID 16.
The possible eventID's are:
1 Remote Inhibit Confirmation
2 Remore Uninhibit confirmation
3 Local inhibit denied
4 Local inhibit timeout
5 Local inhibit confirmation
6 Local uninhibit confirmation
7 Local uninhibit not possible
8 Local uninhibit timeout
A Link in service
B Link Out-of-service, L1_DEAD
C Link Out-of-service, L5_OOS3 NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.79 |
excelPPLEventCPCPPL event received from Call Processing Control, component ID
18. The possible eventID's are:
3 Continuity check incoming failure
4 Failure to ack COT after processing incomming
continuity check
6 Failure to receive RLC after sending RFL
8 Continuity check outgoing failure
20 Maximum number of UTP retries completed without a
response NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.80 |
excelPPLEventSPRCPPL event Signal Procedure Control (SPRC), component ID 19.
The possible eventID's are:
1 Format error in incoming message
2 Undefined CIC in incoming message
3 Undefined message received
4 Confusion Message received
5 Remote user part available
7 Unrecognized message received on unequipped CIC NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.81 |
excelPPLEventBLSPPL event Blocking Signal Sending(BLS), component ID 22. The
possible eventID's are:
1 Format error in incoming message
2 Undefined CIC in incoming message
3 Undefined message received
4 Confusion Message received
5 Remote user part available
7 Unrecognized message received on unequipped CIC NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.82 |
excelPPLEventBLRPPL event received from Blocking Signal Reception(BLR),
component ID 23. The possible eventID's are:
1 Blocking/Unblocking signal reception NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.83 |
excelPPLEventCRSPPL event Circuit Reset Sending (CRS), component ID 24. The
possible eventID's are:
1 First expiration of timer 17 NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.84 |
excelPPLEventCRRPPL event Circuit Reset Reception (CRR), component ID 25.
The possible eventID's are:
1 Circuit Reset Reception NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.85 |
excelPPLEventUCICPPL event Unequipped CIC Reception (UCIC), component Id 26.
The possible eventID's are:
1 Unequipted CIC Reception NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.86 |
excelPPLEventCGRSPPL event Circuit Group Reset Sending (CGRS), component Id 27.
The possible eventID's are:
1 Failure to rcv ack after sending group reset
2 UCIC stop request received (ANSI only) NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.87 |
excelPPLEventCGRRPPL event Circuit Group Reset Reception (CGRR), component Id
28. The possible eventID's are:
1 Failure to rcv ack after sending reset NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.88 |
excelPPLEventGBUSPPL event Circuit Group Un/blocking Sending (GBUS), component
Id 29. The possible eventID's are:
1 Expiration of T19 - No CGBA after GTB
2 Expiration of T21 - No CGUA after CGU
3 CGBA status bit mismatch
4 CGUA status bit mismatch
5 Incorrect parameter in received circuit group
(un)blocking ack. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.89 |
excelPPLEventGBURPPL event Circuit Group Un/blocking Reception (GBUR),
component Id 30. The possible eventID's are:
1 Circuit Group Un/blocking Reception NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.90 |
excelPPLEventHGBRPPL event Hardware Oriented Circuit Group Un/blocking
Reception (HGBR), component Id 32. The possible eventID's
are:
1 Circuit Group Un/blocking Reception NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.91 |
excelPPLEventMTP3HmdtPPL event Message Transfer Part3 Layer (HMDT), component Id
43. The possible eventID's are:
0 Remote processor outage
1 Remote processor restored
2 Local inhibit
3 Local uninhibit
6 UPU MSU received NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.92 |
excelPPLEventMTP3LsacPPL event Message Transfer Part3 Layer (LSAC), component Id
46. The possible eventID's are:
1 Link activation failure
2 Signaling Link failure
3 Signaling link test failure
4 Signaling link restoration NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.93 |
excelPPLEventMTP3TlacPPL event Message Transfer Part3 Layer (TLAC), component Id
60. The possible eventID's are:
0 Remote processor outage
1 Remote processor restored
2 Local inhibit
3 Local uninhibit
4 Remote inhibit
5 Remore uninhibit NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.94 |
excelPPLEventMTP3TsfcPPL event Message Transfer Part3 Layer (TSFC), component Id
63. The possible eventID's are:
1 Destination inaccessable
2 Destination accessable NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.95 |
excelPPLEventISUPHlbPPL event ISUP HLB (ISUP Hardware Failure Oriented Locally
Blocking State), component Id 36. The possible eventID's can
be received are:
1 Hardware Failure Oriented Locally Blocking State NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.96 |
excelPPLEventCRCRPPL event CRCR, component Id 68. The possible eventID's can
be received are:
1 REL received with check indicator set to 3
2 T27 timer expired
3 Second failure of COT NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.97 |
excelPPLEventMGBSPPL event MGBS(Maintaince Circuit Group blocking/unblocking
Sending), component Id 69. The possible eventID's can be
received are:
1 First Expiration of T19
2 First Expiration of T21
3 Stop event received in wait for CGBA state
4 Stop event received in wait for CGUA state NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.98 |
excelPPLEventHGBSPPL event HGBS(Hardware Failure Circuit Group
blocking/unblocking Sending), component Id 71. The possible
eventID's are:
1 First Expiration of T19
2 First Expiration of T21
3 Stop event received in wait for CGBA state
4 Stop event received in wait for CGUA state NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.99 |
excelPPLEventCQSPPL event CQS, component Id 118. The possible eventID's are:
3 Timer T28 expired NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.100 |
excelPPLEventCVSPPL event CVS, component Id 120. The possible eventID's are:
6 CVR receive failed after reattempt NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.101 |
excelPPLEventCRCSPPL event CRCS, component Id 129. The possible eventID's are:
1 T36 expired on continuity recheck
2 COT failure indication, process network IAM
3 T5 expired in waiting for RLC state
4 CPC not IDLE indication NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.102 |
excelPPLEventCROPPL event CRO, component Id 131. The possible eventID's are:
2 T5 expired in Wait for Release Complete State
3 1st continuity recheck attempt failure
4 Continuity recheck attempt failure
5 1st continuity recheck attempt successful NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.103 |
excelDchannelFailureISDN D Channel is establishing. The distant end is not
communicating on the D-channel. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.104 |
excelVoIPModuleOOSThe VDAC Voice over IP module is Out of Service. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.105 |
excelVoipModuleDeadThe VDAC Voice over IP module is no longer communicating. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.106 |
excelVoipModuleDspDeadThe VDAC Voice over IP DSP module is no longer communicating. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.107 |
excelVoipModuleResetThe VDAC Voice over IP module has been reset. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.108 |
excelMatrixSwitchoverA matrix switchover has occurred. NOTIFICATION-TYPE .1.3.6.1.4.1.1751.1.67.0.109 |
excelProducts OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2 |
excelSystem OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.1 |
excelNodeIdentifierAn attribute assigned by the system administrator that
uniquely identifies this host system.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.1.1 |
excelNodeLocationIdentifierA unique identifier is a concatination of identifiers for the
city, state, building and traffic unit identity of this host system.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.1.2 |
excelNodeCurrentTimeThe value for the current time on this host system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.1.3 |
excelSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2 |
excelCurrentNodeThis agent can only view one node at a time. Whatever
this excelCurrentNode is set to is the view against which
other objects are matched. This value represents a LOGICAL node ID.rw INTEGER ( 0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.1 |
excelNodesThe number of nodes or rows in excelNodeTable.ro INTEGER ( 0..32 ) .1.3.6.1.4.1.1751.1.67.2.2.2 |
excelNodeTableThis table contains a row for each node in the switch being
managed by this agent. SEQUENCE OF ExcelNodeEntry .1.3.6.1.4.1.1751.1.67.2.2.3 |
excelNodeEntryDefinition for the ExcelNodeEntry List ExcelNodeEntry .1.3.6.1.4.1.1751.1.67.2.2.3.1 |
excelNodeIndexThis object is a unique identifieer into the excelNodeTable. INTEGER (0..32 ) .1.3.6.1.4.1.1751.1.67.2.2.3.1.1 |
excelNodeLogicalIDThis object represents the logical ID that the host application
assigns to the node represented by this row.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.3.1.2 |
excelNodePhysicalIDThis object represents the unique physical number used to identify
the node. It is the serial number of the midplane.ro INTEGER (0..8192 ) .1.3.6.1.4.1.1751.1.67.2.2.3.1.3 |
excelNodeTypeThis object indicates the node type of the node being managed.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.3.1.4 |
excelNode OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4 |
excelNodeHardware OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1 |
excelCommunicationEquipment OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1 |
excelCommunicationCard OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1 |
excelCommCardTableThis table contains a row for each communication card in this node.
A communication card is considered to be a card that plays a role in
the call processing capabilities of the node. SEQUENCE OF ExcelCommCardEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1 |
excelCommCardEntry ExcelCommCardEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1 |
excelCommCardSlotIndexThis object represents the slot number occupied by this card. Note
that this value is the index into the excelDeviceCardTable. SlotsInNode .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1.1 |
excelCommCardOperStateThis object represents the state of this card. oosBySwitch(2)
indicates that the switch has taken the card out of service.
oosByHost(3) indicates that the host has taken the card out of
service. standbyByHost(4) indicates that the host has put the card
in a standby state. If this object is generalHWFailure(5), then the
card is off-line and must be serviced. needsSystemSW(6) indicates
that System Software needs to be downloaded to the switch.ro CardOperState .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1.2 |
excelCommCardResetReasonThis object represents the reason for this card's last reset.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1.3 |
excelCommCardConfigStatusThis object represents the state of the battery-backed configuration
data. If it is invalid(1), then the card must be reconfigured by the
host.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1.4 |
excelCommCardConfidenceTestIndicates status of Confidence test.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1.5 |
excelCommCardActionThis object contains the actions that can occur on a card. These
include :
locked - takes the card out of service, but leave the current
configuration intact.
unlocked - puts a card out of service back into service
shutdown - intermediate state when card is in the process of
being locked.rw Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1.6 |
excelCommCardActionTimeDate and time of last action taken.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.1.1.1.7 |
excelDSP OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2 |
excelVoipDsp OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1 |
excelVoipSlotNumberThis object represents the index of the card that information will be
presented onrw INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.1 |
excelVoipDspTable SEQUENCE OF ExcelVoipDspEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2 |
excelVoipDspEntry ExcelVoipDspEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1 |
excelVoipDspIndexIndex into the Voice over IP DSP table INTEGER ( 1..4 ) .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.1 |
excelVoipDspInstalledThis object indicates if the DSP module is installed or not.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.2 |
excelVoipDspNumChannelsSupportedThis object indicates the number of channels available from the slot.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.3 |
excelVoipDspOperStateThis object indicates operational state of the dsp.ro CardOperState .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.4 |
excelVoipDspArtworkRevisionThis object indicates operational state of the dsp.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.5 |
excelVoipDspFuncRevisionThis object indicates function revision of this dsp.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.6 |
excelVoipDspHWRevisionThis object indicates function version of the hardware associated
of this dsp.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.7 |
excelVoipDspSWRevisionThis object indicates function version of the software associated
of this dsp.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.8 |
excelVoipDspRamSizeThis object indicates the current amount of RAM on this dsp.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.9 |
excelVoipDspSerialNumThis object indicates the serial number of this dsp.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.10 |
excelVoipDspRamBuildNumberThis object indicates the build number of this dsp.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.1.2.1.2.1.11 |
excelDeviceEquipment OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.2 |
excelDeviceCard OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1 |
excelDeviceCardTableThe excelDeviceCardTable, which has a row for
each of the 'slots' (the maximum being, excelConfigMaxSlot) in this
node. Note that this table will have an entry for each slot whether
it is filled or not. It is ordered by slot number. And a slot does
not necessarily mean that the card is hot swappable, like the fan tray
or midplane. The columns represent information that
(for the most part) is common between all types of cards. SEQUENCE OF ExcelDeviceCardEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1 |
excelDeviceCardEntry ExcelDeviceCardEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1 |
excelDeviceCardSlotIndexThis is the slot number of the slot that the card resides in as
well as the index into excelDeviceCardTable. SlotsInNode .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.1 |
excelDeviceCardTypeThe type of card that is in this slot. If the slot does not
contain a card, then the value is empty(2). It the card is unable
to communicate, then the value is dead(3). If the agent is unfamiliar
with the card, then the value is other(1). Otherwise, it is a value
representing one of the appropriate Excel products that can reside in
this slot.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.2 |
excelDeviceCardModelDescriptionThis object is an ASCII string that represents the model description
of the card in this slot.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.3 |
excelDeviceCardArtworkRevisionThis field has an ASCII character in the range 'A' to 'Z'
(0x41-0x5B) which indicates the revision level of the
card's Printed Circuit Artwork.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.4 |
excelDeviceCardFuncRevisionThis object indicates the card's functional revision level.ro INTEGER ( 0..2048 ) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.5 |
excelDeviceCardHWRevisionThis object is an ASCII string that represents the ROM Revision of
the card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.6 |
excelDeviceCardSWRevisionThis object is an ASCII string that represents the revision levels of
the system software running on this card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.7 |
excelDeviceCardRamSizeThis object indicates the amount of RAM that is on the card. The RAM
is measured in 1K increments.ro INTEGER ( 0..8192 ) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.8 |
excelDeviceCardSerialNumThis object contains the serial number of the card.ro INTEGER ( 0..32565 ) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.9 |
excelDeviceCardRAMBuildNumThis object contains the RAM Build number of the card.ro INTEGER ( 0..32565 ) .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.1.1.1.10 |
excelUtility OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.2.2 |
excelResourceEquipment OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3 |
excelResourceUtilization OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1 |
excelResourceSlotIdThis object represents the index of the card information will be
presented onrwobsolete INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.1 |
excelResourceUsageTable SEQUENCE OF ExcelRegionEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.2 |
excelResourceUsageEntry ExcelResourceUsageEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.2.1 |
excelResourceUsageIndex INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.2.1.1 |
excelCpuTimeThis object represents the total amount of CPU time that has been
used by the selectd card.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.2.1.2 |
excelMcbUsageThis object represents the percentage MCB's currently in usero INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.2.1.3 |
excelRegionTable SEQUENCE OF ExcelRegionEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.3 |
excelRegionEntry ExcelRegionEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.3.1 |
excelRegionIndex INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.3.1.1 |
excelRegionIdro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.3.1.2 |
excelRegionSizero INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.3.1.3 |
excelRegionUsedThe number of bytes in this region that are currently in usero INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.3.1.4 |
excelPartitionTable SEQUENCE OF ExcelPartitionEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.4 |
excelPartitionEntry ExcelPartitionEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.4.1 |
excelPartitionIndex INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.4.1.1 |
excelPartitionIdro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.4.1.2 |
excelPartitionSizero INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.4.1.3 |
excelPartitionUsedThe number of bytes in this partition that are currently in usero INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.4.1.4 |
excelCpuUsageTable SEQUENCE OF ExcelCpuUsageEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.5 |
excelCpuUsageEntry ExcelCpuUsageEntry .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.5.1 |
excelCpuUsageIndex INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.5.1.1 |
excelCpuUsageTaskIdro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.5.1.2 |
excelCpuUsageUsedro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.1.3.1.5.1.3 |
excelNodeSoftware OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2 |
excelSystemSoftware OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1 |
excelSystemConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.1 |
excelSystemAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.2 |
excelSysLastAlarmTrapThis object represents the last trap that has been sent by this
agent.ro INTEGER (0..1024 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.2.1 |
excelSysLastAlarmSeverityIf an alarm occurred and a trap was sent, then this object
indicates the severity.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.2.2 |
excelSysLastAlarmNodeThe Physical Node ID of the last node to encounter
an alarm condition.ro INTEGER ( 0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.2.3 |
excelSysLastAlarmStatusThe last Alarm Status change value to go out in a trap.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.2.4 |
excelSysLastAlarmDSPLastBlockedThe last DSP Function Type that was blocked.ro DSPFunctionTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.2.5 |
excelSysLastAlarmRefClockSrcIf a Reference Clock Source Lost alarm occurred,
this object stores which reference clock the alarm
is occurring on. If this alarm has not occurred, then
the value will be equal to notApplicable(1).ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.2.6 |
excelRing OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3 |
excelRingTableIt is possible for a node to be a member of numerous rings.
Therefore, each row of this table describes the characteristics
of each ring of which this node is a member. SEQUENCE OF ExcelRingEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2 |
excelRingEntryDefinition of the ExcelRingEntry sequence ExcelRingEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1 |
excelRingLogicalIDIndexThe logical ID of the ring being described by this row. INTEGER ( 0..8 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.1 |
excelRingStatusThis object represents the status of the proprietary fiber network
that connects the nodes of an EXS. If this object equals
outOfService(5), then excelRingOOSReason will contain
the reason that this ring is considered out of service.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.2 |
excelRingOOSReasonIf the node has been declared out of service on this ring, and
excelRingStatus equals outOfService(5), then this object will
equal any value other than none(1).ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.3 |
excelRingTransmitModeThe transmit mode of this node as it relates to this ringro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.4 |
excelRingNodeRoleThe role that this node palys in this ringro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.5 |
excelRingCtrlSlotThe slot in which the EXNET I/O controller resides for this node.ro SlotsInNode .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.6 |
excelRingPortAStatusThe status of port A on the EXNET I/O controller card for this
node on this ring.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.7 |
excelRingPortBStatusThe status of port B on the EXNET I/O controller card for this
node on this ring.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.8 |
excelRingSourcePacketIDThe lowest packet ID assigned to this node for this ring.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.3.2.1.9 |
excelRingNodeStatus OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4 |
ringIDThe id of this ringro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.1 |
ringStatusTableThis table describes the phyysical and logical contents of the
selected ring. SEQUENCE OF RingStatusTableEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2 |
ringStatusTableEntry RingStatusTableEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1 |
ringStatusIndexIndex into the ring status entry table INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.1 |
ringStatusTransmittingIs this node currently transmitting on a ring.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.2 |
ringStatusIpAddressThe IP address of this object on the ringro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.3 |
ringStatusLogicalIdThe logical ID of this node on the ringro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.4 |
ringStatusPhysicalIdThe physical Id on this node on the ring.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.5 |
ringStatusLoadMajorRevThe major revision number of the current buildro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.6 |
ringStatusLoadMinorRevThe minor revision number of the current buildro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.7 |
ringStatusLoadBuildNumThe number of the current buildro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.1.4.2.1.8 |
excelCommunicationSoftware OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2 |
excelMatrix OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1 |
excelMtxTableThis table contains an entry for each matrix card in
the system. Note that in an EXnet Connect system, there will be a row
in this table to represent the EXnet Connect Card. SEQUENCE OF ExcelMtxEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1 |
excelMtxEntry ExcelMtxEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1 |
excelMtxSlotIndexThe slot in which the matrix represented by this row resides. SlotsInNode .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.1 |
excelMtxPositionThis object indicates the physical position of this matrix card.
Left(1), Right(2), or Other(3)ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.2 |
excelMtxTypeThis object indicates the node type of this matrix card.
other(1), pcx(2), csn(3), lnx(4), or exnetConnect(5).ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.3 |
excelMtxStateThis object indicates the current state of this matrix card.
The possible return values are:
booting(1),
initializing(2),
standby(3),
switchOver(4),
active(5),
other(6),
disabled(7).ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.4 |
excelMtxAdjacentMatrixStatusThis object indicates the status of the adjacent matrix card.
notPresent(1), detected(2), noHost(3), ok(4), other(5)ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.5 |
excelMtxHostLinkThis object indicates the status of the matrix card host link.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.6 |
excelMtxRamLoadPresentThis object indicates the status of the matrix card download.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.7 |
excelMtxReadyForConfigurationThis object indicates the state of the matrix card.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.8 |
excelMtxIpAddressThis object is the IP Address associated with the currently
active matrix card.ro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.9 |
excelMtxBootMajorVersionCurrent value of the major version number of the boot software.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.10 |
excelMtxBootMinorVersionIf value is equal to zero (0), no system software is presentro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.11 |
excelMtxSystemSoftwareMajorIf value is equal to zero (0), no system software is presentro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.12 |
excelMtxSystemSoftwareMinorIf value is equal to zero (0), no system software is presentro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.13 |
excelMtxSystemSoftwareBuildIf value is equal to zero (0), no system software is presentro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.14 |
excelMtxSecIpAddressThis object is the IP Address associated with the current
atand-by matrix card.ro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.1.1.15 |
excelMatrixManagement OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.2 |
excelMatrixSwitchOverThis object provides capabilty to cause a matrix switchoverrw Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.2.1 |
excelMatrixSwitchOverTimeThe date and time when the matrix switchover occurredro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.1.2.2 |
excelExnetConnect OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.2 |
excelExnetConnectTableThis table contains a row for each EXNET Connect Card in the PC
Chassis. SEQUENCE OF ExcelExnetConnectEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.2.1 |
excelExnetConnectEntryDefinition of the ExcelExnetConnectEntry sequence ExcelExnetConnectEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.2.1.1 |
excelExnetConnectLogicalNodeIDIndexThis object is the logical Node ID that has been assigned to this
EXNET Connectro INTEGER ( 0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.2.1.1.1 |
excelExnetConnectClockMasterThis object indicates whether or not the EXNET Connect
Card is the clock master on the bus. If the value is
yes(2), then the EXNET Connect card is the clock master.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.2.1.1.2 |
excelExnetConnectClockSpeedThe clock speed of the resource bus on this EXNET
Connect.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.2.1.1.3 |
excelSpans OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3 |
excelGeneralSpan OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1 |
excelSpanTableThis table contains a row for each active span defined on a line card
contained in the chassis. SEQUENCE OF ExcelSpanEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1 |
excelSpanEntryDefinition of the ExcelSpanEntry sequence ExcelSpanEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1.1 |
excelSpanTableIndexThe Logical Span ID being accessed INTEGER (0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1.1.1 |
excelLogicalSpanIdThe Logical Span ID being accessedro INTEGER (0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1.1.2 |
excelSpanBipolarViolationThe number of Bipolar Violations that have occurred on
this span since the span became active or since the last requestro Counter32 .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1.1.3 |
excelSpanFrameErrorsIf the queried span in a T1 span, then this field will
contain the number of Bit Frame Errors that have occurred on this span
since the span became active or since the last request.
If the queried span in an E1 span, then this field will contain the
number of Frame Alignment Signal Errors that have occurred on this
span since the span became active or since the last requestro Counter32 .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1.1.4 |
excelSpanSlipErrorsThe number of slips that have occurred on this span since
the span became active or since the last requestro Counter32 .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1.1.5 |
excelSpanLossofFrameThe number of loss of frame that have occurred on this
span since the since the last requestro Counter32 .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.1.1.1.6 |
excelSpanManagement OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.2 |
excelCurrentSpanIdThe id of the span an in/out of service action will occur on.rw INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.2.1 |
excelSpanActionThe action to be taken againts the span id defined by
excelCurrentSpanId.rw Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.2.2 |
excelChannelActionThe action to be taken againts the channels associated with
the span as defined in excelCurrentSpanIDrw Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.3.2.3 |
excelSS7 OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4 |
excelSS7Config OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1 |
excelSS7CardTableThis table contains a row for each SS7 Card in the current node. SEQUENCE OF ExcelSS7CardEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1 |
excelSS7CardEntryDefinition of the ExcelSS7CardEntry sequence ExcelSS7CardEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1 |
excelSS7CardSlotNumberIndexThis entry represents slot number in which this card resides. INTEGER (0..64 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.1 |
excelSS7CardRedundancyConfiguredRoleThis entry represents the configured role of this card in SS7
redundancy. The current role may be differentro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.2 |
excelSS7CardRedundancyCurrentRoleThis entry represents the current role of this card in SS7
redundancy.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.3 |
excelSS7CardRedundancyMateThis entry represents the slot number of the SS7 card associated
with this card for the purpose of SS7 redundancy. A value of 255
(0xff) indicates that there is no association.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.4 |
excelSS7CardRedundancyStatusThis entry represents the current role of this card in
SS7 redundancy.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.5 |
excelSS7CardStackID1This entry represents the ID of the first of four possible stack ids
resident on this card. A value of 255 (0xff) indicates not configured.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.6 |
excelSS7CardStackID2This entry represents the ID of the second of four possible stack
id resident on this card. A value of 255 (0xff) indicates not
configured.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.7 |
excelSS7CardStackID3This entry represents the ID of the third of four possible stack ids
resident on this card. A value of 255 (0xff) indicates not configured.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.8 |
excelSS7CardStackID4This entry represents the ID of the fourth of four possible stack
ids resident on this card. A value of 255 (0xff) indicates not
configured.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.9 |
excelSS7CardMaximumLinksThis entry represents the maximum number of links supported by this
card.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.1.1.10 |
excelSS7ConfigLinkTableThis table contains a row for each link that is assigned in the node. SEQUENCE OF ExcelSS7LinkEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2 |
excelSS7LinkEntryDefinition of the ExcelSS7LinkEntry sequence ExcelSS7LinkEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1 |
excelSS7LinkStackIndexThis entry represents the Stack with which this link is associated.
A value of 255 (0xff) indicates not configured. INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.1 |
excelSS7LinkLinkIndexThis entry represent the ID of this link. A value of 255 (0xff)
indicates not configured. INTEGER(0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.2 |
excelSS7LinkLinkSetIndexThis entry represents the Link Set with which this link is
associated. A value of 255 (0xff) indicates not configured. INTEGER(0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.3 |
excelSS7LinkStatusThis entry represents the status of this link.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.4 |
excelSS7LinkSignalingLinkCodeThis entry represents the Signaling Link Code.ro INTEGER (0..1024 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.5 |
excelSS7LinkDataRateThis entry represents the data rate for this link.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.6 |
excelSS7LinkLogicalSpanIDThis entry represents the Logical Span on which this link resides.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.7 |
excelSS7LinkchannelThis entry represents the Channel Offset on which this link resides.ro INTEGER (0..8192 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.2.1.8 |
excelSS7StackTableThis table contains a row for each SS7 Stack in the current node. SEQUENCE OF ExcelSS7StackEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3 |
excelSS7StackEntryDefinition of the ExcelSS7StackEntry sequence ExcelSS7StackEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1 |
excelSS7StackIDIndexThis entry represents the stack id. INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1.1 |
excelSS7StackOPCThis entry represents this Origination Point Code for this SS7 node.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1.2 |
excelSS7StackMTPVariantThis entry represents the MTP variant supported.ro SS7VariantsTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1.3 |
excelSS7StackISUPVariantThis entry represents the ISUP variant supported.ro SS7VariantsTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1.4 |
excelSS7StackL3PVariantThis entry represents the L3P variant supported.ro SS7VariantsTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1.5 |
excelSS7StackTUPVariantThis entry represents the TUP variant supported.ro SS7VariantsTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1.6 |
excelSS7StackL3PTUPVariantThis entry represents the L3P TUP variant supported.ro SS7VariantsTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.3.1.7 |
excelSS7LinkSetTableThis table contains a row for each SS7 LinkSet in the current node. SEQUENCE OF ExcelSS7LinkSetEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.4 |
excelSS7LinkSetEntryDefinition of the ExcelSS7LinkSetEntry sequence ExcelSS7LinkSetEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.4.1 |
excelSS7LinkSetIDIndexThis entry represents the logical link set id. INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.4.1.1 |
excelSS7LinkSetStatusThis entry represents the link set status.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.4.1.2 |
excelSS7LinkSetAPCThis entry represents the APC for this link.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.4.1.3 |
excelSS7LinkSetStackIDIndexThis entry represents the Logical Stack ID associated with
this link.ro INTEGER (0..1024 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.1.4.1.4 |
excelSS7Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.4.2 |
excelPPL OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5 |
excelPPLComponentIdComponent id of the PPL event being processedro INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.1 |
excelPPLComponentStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2 |
excelL3PCICTableThis table will contain information on the ppl L3P CIC events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
8 Remote maintaince block indication
15 Remote hardware group block indication
18 Local maintaince block success
22 UCIC received SEQUENCE OF ExcelL3PCICEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1 |
excelL3PCICEntry ExcelL3PCICEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1 |
excelL3PCICIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1.1 |
excelL3PCICSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1.2 |
excelL3PCICChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1.3 |
excelL3PCICEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1.4 |
excelL3PCICTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1.5 |
excelL3PCICCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1.6 |
excelL3PCICStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.1.1.7 |
excelL3PLinkTableThis table will contain information on the ppl L3P link events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
10 - Link in service
11 - Link out-of-service, L1_DEAD
12 - Link out of service, L5_OOS SEQUENCE OF ExcelL3PCICEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2 |
excelL3PLinkEntry ExcelL3PLinkEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1 |
excelL3PLinkIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1.1 |
excelL3PLinkSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1.2 |
excelL3PLinkChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1.3 |
excelL3PLinkEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1.4 |
excelL3PLinkTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1.5 |
excelL3PLinkCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1.6 |
excelL3PLinkStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.2.1.7 |
excelCPCTableThis table will contain information on the ppl CPC events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
20 Maximum number of UTP retries completed without a response SEQUENCE OF ExcelCPCEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3 |
excelCPCEntry ExcelCPCEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1 |
excelCPCIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1.1 |
excelCPCSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1.2 |
excelCPCChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1.3 |
excelCPCEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1.4 |
excelCPCTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1.5 |
excelCPCCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1.6 |
excelCPCStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.3.1.7 |
excelSPRCTableThis table will contain information on the ppl SPRC events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
2 Undefined CIC in incoming message
5 Remote user part available SEQUENCE OF ExcelSPRCEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4 |
excelSPRCEntry ExcelSPRCEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1 |
excelSPRCIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1.1 |
excelSPRCSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1.2 |
excelSPRCChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1.3 |
excelSPRCEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1.4 |
excelSPRCTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1.5 |
excelSPRCCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1.6 |
excelSPRCStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.4.1.7 |
excelUCICTableThis table will contain information on the ppl UCIC events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
1 Unequipped CIC reception SEQUENCE OF ExcelUCICEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5 |
excelUCICEntry ExcelUCICEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1 |
excelUCICIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1.1 |
excelUCICSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1.2 |
excelUCICChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1.3 |
excelUCICEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1.4 |
excelUCICTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1.5 |
excelUCICCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1.6 |
excelUCICStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.5.1.7 |
excelHMDTTableThis table will contain information on the ppl HMDT events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
0 Remote processor outage
2 Local Inhibit
6 UPN MSU Received SEQUENCE OF ExcelHMDTEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6 |
excelHMDTEntry ExcelHMDTEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1 |
excelHMDTIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1.1 |
excelHMDTSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1.2 |
excelHMDTChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1.3 |
excelHMDTEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1.4 |
excelHMDTTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1.5 |
excelHMDTCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1.6 |
excelHMDTStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.6.1.7 |
excelLSACTableThis table will contain information on the ppl LSAC events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
2 Signaling Link Failure SEQUENCE OF ExcelLSACEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7 |
excelLSACEntry ExcelLSACEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1 |
excelLSACIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1.1 |
excelLSACSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1.2 |
excelLSACChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1.3 |
excelLSACEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1.4 |
excelLSACTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1.5 |
excelLSACCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1.6 |
excelLSACStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.7.1.7 |
excelTLACTableThis table will contain information on the ppl TLAC events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
0 Remote processor outage
2 Local Inhibit
4 Remote Inhibit SEQUENCE OF ExcelTLACEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8 |
excelTLACEntry ExcelTLACEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1 |
excelTLACIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1.1 |
excelTLACSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1.2 |
excelTLACChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1.3 |
excelTLACEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1.4 |
excelTLACTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1.5 |
excelTLACCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1.6 |
excelTLACStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.8.1.7 |
excelTSFCTableThis table will contain information on the ppl TSFC events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
1 Destination Insaccessible SEQUENCE OF ExcelTSFCEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9 |
excelTSFCEntry ExcelTSFCEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1 |
excelTSFCIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1.1 |
excelTSFCSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1.2 |
excelTSFCChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1.3 |
excelTSFCEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1.4 |
excelTSFCTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1.5 |
excelTSFCCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1.6 |
excelTSFCStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.9.1.7 |
excelCROTableThis table will contain information on the ppl CRO events
receicved and the date and time of the last one received. Only the
following event ID will be captured:
4 Continuity recheck attepmt failure SEQUENCE OF ExcelCROEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10 |
excelCROEntry ExcelCROEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1 |
excelCROIndexIndex into this table. INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1.1 |
excelCROSpanIDThe id of the span this event has occurred on.rw INTEGER ( 0..84 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1.2 |
excelCROChannelIDThe id of the channel this event has occurred on.rw INTEGER ( 0..16 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1.3 |
excelCROEventIDId of the event that has occurred.rw INTEGER ( 0..99 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1.4 |
excelCROTimeThe time of the last occurance of this event.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1.5 |
excelCROCountThe current number of times this event has occurred since system
startuprw INTEGER ( 0..32656 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1.6 |
excelCROStatusThe status of this program entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.5.2.10.1.7 |
excelISDN OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6 |
excelISDNConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1 |
excelISDNConfigDChanTableThis table contains a row for each D Channel that is assigned in the
node. SEQUENCE OF ExcelISDNConfigDChanEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1 |
excelISDNConfigDChanEntryDefinition of the ExcelISDNConfigDChanEntry sequence ExcelISDNConfigDChanEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1 |
excelISDNConfigDChanSpanIndexThe Logical Span ID of the span which contains the channel assigned
to the D Channel represented by this row.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.1 |
excelISDNConfigDChanIndexThe Channel ID of the channel assigned to the D Channel represented
by this row.ro INTEGER (0..255 ) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.2 |
excelISDNConfigDChanConnTypeThe connection type of the D Channel represented by this row.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.3 |
excelISDNConfigDChanHDLCBitPolThe HDLC Bit Polarity of the D Channel represented by this row.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.4 |
excelISDNConfigDChanBChanSelectThe B Channel Selection Mode associated with the D Channel that is
represented by this row.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.5 |
excelISDNConfigDChanBChanEncTransThe B Channel Encoding for transmission associated with the D Channel
that is reprsented by this row.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.6 |
excelISDNConfigDChanLocationThe location of the D Channel represented by this row.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.7 |
excelISDNConfigDChanPhysicalMediumThe physical medium of the D channel. Typically a 64kbps
T1/E1/J1 line.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.6.1.1.1.8 |
excelMediaGateway OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7 |
excelMGSystem OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.1 |
excelMGActiveProtocolThe current active protocol executing on the matrix.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.1.1 |
excelMGSystemNameThe name of the Media Gateway system. The default name will the
IP Address of the active matrix.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.1.2 |
excelMGNumSlotsThe number of slots in th e chassis available for Media Gateway
Hardware.ro SlotsInNode .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.1.3 |
excelMGVoip OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2 |
excelVoipAddressTable SEQUENCE OF ExcelVoipAddressEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1 |
excelVoipAddressEntry ExcelVoipAddressEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1.1 |
excelVoipAddressIndexThis is the index into the excel VoIP address table . INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1.1.1 |
excelVoipAddressEntityTypeThis object describes the entity on the Vdac card being displayed.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1.1.2 |
excelVoipIpAddressThis object displays the IP Address assigned to the current entity.ro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1.1.3 |
excelVoipSubNetMaskThis object displays the subnet mask assigned to the current entity.ro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1.1.4 |
excelVoipIpGatewayThis object displays the default IP Gateway Address assigned to the
current entity.ro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1.1.5 |
excelVoipResetIndicatorThis object discribes if an object reset is needed.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.1.1.6 |
excelMGResAttrIpAddressThis object displays the IP Address needed to get Resource Attribute
information.rw IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.2 |
excelMGResourceAttributeTable SEQUENCE OF ExcelMGResourceAttributeEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3 |
excelMGResourceAttributeEntry ExcelMGResourceAttributeEntry .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1 |
excelMGResAttrIndexIndex into the excelMGResourceAttribute table. SlotsInNode .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.1 |
excelMGPayloadTypero PayloadTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.2 |
excelMGPayloadSizeThe basic packet rate of an RTP Packet that is sent out over Ethernetro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.3 |
excelMGSilenceSupressionThis object indicates if silence supression has been enabled.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.4 |
excelMGEchoCancellationThis object determines if echo cancellation logic is enabled or not.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.5 |
excelMGMinDelayValueTime in milliseconds of the minimum delay value.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.6 |
excelMGMaxDelayValueTime in milliseconds of the maximum delay value.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.7 |
excelMGAdaptionRateTime in milliseconds of the adaption ratero INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.8 |
excelMGFaxTypeThe object returns the current Fax type.ro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.9 |
excelMGModemEnableTransportro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.10 |
excelMGBypassCoderTypeThe object returns the current bypass coder types.ro PayloadTypes .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.11 |
excelMGRtpPacketDepthThis object returns the redundancy packet depth for RTP.ro PacketDepth .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.12 |
excelMGFaxPacketDepthThis objects returns the current Fax redundancy packet depth.ro PacketDepth .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.13 |
excelMGModemPacketDepthThis object returns the current modem redundancy packet depth.ro PacketDepth .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.14 |
excelMGTypeOfServicePrecedencero Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.15 |
excelMGTypeOServiceDelayro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.16 |
excelMGTypeOfServiceThroughputro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.17 |
excelMGTypeOfServiceReliabilityro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.18 |
excelMGTypeOfServiceCostro Enumeration .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.19 |
excelMGRtcpPortOffsetThis object returns the current modem redundancy packet depth.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.20 |
excelMGT38PortOffsetThis object returns the current modem redundancy packet depth.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.2.3.1.21 |
excelMGConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.3 |
excelMGConfigPrimaryMGCAddressIP Address of the primary softswitch (call agent)ro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.3.1 |
excelMGConfigPrimaryPortThe port number used when connection to the primary softswitch call
agentro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.3.2 |
excelMGConfigSecondaryMGCAddressIP Address of the secondary softswitch (call agent)ro IpAddress .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.3.3 |
excelMGConfigSecondaryPortThe port number used when connection to the secondary softswitch call
agentro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.3.4 |
excelMGConfigLocalPortPort number assigned to the local protocol taskro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.3.5 |
excelMGConfigIpdc OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.4 |
excelMGConfigIpdcReconnectAttemptsThe number of time the local protocol task will attempt to connect
to the currently active Call Agentro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.4.1 |
excelMGConfigMgcp OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.5 |
excelConfigMgcpPriTransmitIntervalCount used when switching over to a secondary call agent from a
primary call agentro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.5.1 |
excelConfigMgcpSecTransmitIntervalCount used when switching over to a primary call agent from a
secondary call agentro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.5.2 |
excelConfigMgcpResponseIntervalThis object specifies the time the gateway holds onto a message
response sent to the CA. This is for solicited messages sent from the
CA. If the time expires, then the gateway removes the response from
the response queue. If the CA sends another solicited message to the
gateway and the response is in the response queue, then the gateway
sends the response which is contained in the response queue. This
essentially means that for every solicited message sent from the CA,
the gateway looks in its response queue to see if it has a response
for that message.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.5.3 |
excelConfigMgcpRetransmissionTimeWhen the gateway sends an unsolicited message to the CA, and if a
response is not received, this parameter specifies the time before
the gateway resends the message.ro INTEGER .1.3.6.1.4.1.1751.1.67.2.2.4.2.2.7.5.4 |
excelOAMP OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.3 |
excelEXSAgentVerboseThis variable will allow debugging messages to be turned off and on
dynamically for the EXSAgent processrw Enumeration .1.3.6.1.4.1.1751.1.67.2.3.1 |
excelEXSEventManagerVerboseThs object allows the end users to turn debugging information on
dynamically for process EXSEventManager.rw Enumeration .1.3.6.1.4.1.1751.1.67.2.3.2 |
excelExtension OBJECT IDENTIFIER .1.3.6.1.4.1.1751.1.67.2.4 |