ACMIB
AI MIB Summary
The ACMIB module enables SNMP-based monitoring and management of Lucent Access Concentrator hardware running Release 6.2, specifically tracking interface status, port statistics, and system resource utilization for legacy DSLAM and access node deployments.
Lucent Access Concentrator, Release 6.2
Main OID:
acMIB.1.3.6.1.4.1.1751.2.18
3217
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
3217 total| Object Name |
|---|
lucent OBJECT IDENTIFIER .1.3.6.1.4.1.1751 |
mibs OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2 |
acMIBLucent Access Concentrator, Release 6.2 MODULE-IDENTITY .1.3.6.1.4.1.1751.2.18 |
sysConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.1 |
siteNamesite name - asciirw DisplayString .1.3.6.1.4.1.1751.2.18.1.1 |
siteIDsite id - numericalrw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.2 |
siteEtherIpAddrip address for ethernet access to the site
(switch)rw IpAddress .1.3.6.1.4.1.1751.2.18.1.3 |
siteEtherIpMaskip mask for ethernet access to the site
(switch)rw IpAddress .1.3.6.1.4.1.1751.2.18.1.4 |
siteGatewayAddrip address for gateway access to the site
(switch)rw IpAddress .1.3.6.1.4.1.1751.2.18.1.5 |
siteAtmAddrPrefix1This is one of the two atm address prefix
of this switch.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.6 |
siteAtmAddrUser1This is one of the two atm address user part
of this switch.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.7 |
siteRemoteMgrAddr1remote manager IP Address, where TRAP will be
sent to.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.8 |
siteRemoteMgrAddr2remote manager IP Address, where TRAP will be
sent to.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.9 |
siteRemoteMgrAddr3remote manager IP Address, where TRAP will be
sent to.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.10 |
siteRemoteMgrAddr4remote manager IP Address, where TRAP will be
sent to.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.11 |
siteRemoteMgrAddr5remote manager IP Address, where TRAP will be
sent to.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.12 |
siteMasterNodeAtmAddr1Master node atm address, where TRAP will be
sent to.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.13 |
siteMasterNodeAtmAddr2Master node atm address, where TRAP will be
sent to.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.14 |
siteEnhanceFeaturesenhancement features capability -
number consists of a sum to represent
the following:
1: securedAtm
2: isdn
4: frameRelayro INTEGER .1.3.6.1.4.1.1751.2.18.1.15 |
siteTrapDialOutFeatureEnables the dialing out to a remote terminal
or beeper for trap notification.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.16 |
siteTrapDialOutPhoneNumPhone number of the terminal to dial when
trap notifications are phoned outrw DisplayString .1.3.6.1.4.1.1751.2.18.1.17 |
siteTrapDialOutBeeperDataData (phone digits) to send to beeper if the
dialBeeper option is selected.rw DisplayString .1.3.6.1.4.1.1751.2.18.1.18 |
siteDateAndTimeCurrent date and time: 11 octets
octet# contents range
1-2 year 0..65536
3 month 1..12
4 day 1..31
5 hour 0..23
6 minutes 0..59
7 seconds 0..60(60=leap second)
8 deci-seconds 0..9
9 direction from UTC '+'/'-'
10 hours from UTC 0..11
11 minutes from UTC 0..59rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.1.19 |
siteSoftwareVersionConstant value representing the version number
of the current software.ro DisplayString .1.3.6.1.4.1.1751.2.18.1.20 |
csTcpServerIpAddressThe IP address of CSrw IpAddress .1.3.6.1.4.1.1751.2.18.1.21 |
csTcpServerPortNumberThe Port Number used for communication
with CS.
NOTE: Port # 5000 and 6000 have been
reservered for AC products.
DO NOT USED THEM !!!rw INTEGER ( 1025..65535 ) .1.3.6.1.4.1.1751.2.18.1.22 |
keepAliveTimerkeep alive timer can be set inbetween
0 and 999999999rw INTEGER ( 0..999999999 ) .1.3.6.1.4.1.1751.2.18.1.23 |
inactiveTimerinactive timer can be set inbetween
0 and 999999999rw INTEGER( 0..999999999 ) .1.3.6.1.4.1.1751.2.18.1.24 |
siteMasterNodeAddrType1Type of address specified for master node atm
address, where TRAP will be sent to.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.25 |
siteMasterNodeAddrType2Type of address specified for master node atm
address, where TRAP will be sent to.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.26 |
inBandPrimaryIpAddressIP address of the switch when the switch is
accessed over the primary in-band connection.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.27 |
inBandPrimaryIpMaskIP address subnet mask of the primary in-band
management IP address.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.28 |
inBandBackupIpAddressIP address of the switch when the switch is
accessed over the secondary in-band connection.ro IpAddress .1.3.6.1.4.1.1751.2.18.1.29 |
inBandBackupIpMaskIP address subnet mask of the secondary in-band
management IP address.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.1.30 |
inBandSvcConnectionsAllowedFlag indicating whether in-band management should
be supported over SVCs.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.31 |
atmArpServerThis flag indicates if this switch is an ATM ARP
server.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.32 |
atmArpServerRemoteConnectionTypeWhen this switch is not the ATM ARP server,
indicates whether the connection to the ATM ARP
server uses SVCs or PVCs.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.33 |
atmArpServerRemoteAtmAddressThe ATM address of the ATM ARP server when this
switch is not the ATM ARP server and the
connection to the ATM ARP server uses SVCs.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.34 |
atmArpServerRemoteAddrTypeThe format of the ATM address of the ATM ARP
server when this switch is not the ATM ARP server
and the connection to the ATM ARP server uses
SVCs.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.35 |
atmArpServerRemoteIpAddressThe IP address of the ATM ARP server when this
switch is not the ATM ARP server and the
connection to the ATM ARP server uses PVCs.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.36 |
atmArpServerRemoteIpMaskThe IP address subnet mask of the ATM ARP server
when this switch is not the ATM ARP server and the
connection to the ATM ARP server uses PVCs.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.37 |
atmArpServerEncapsulationThe type of encapsulation used for IP packets over
ATM in in-band management.ro Enumeration .1.3.6.1.4.1.1751.2.18.1.38 |
siteFallbackSoftwareVersionConstant value representing the version number
of the software to fallback to.ro DisplayString .1.3.6.1.4.1.1751.2.18.1.41 |
siteUpgradeSoftwareVersionConstant value representing the version number
of the software to upgrade to.ro DisplayString .1.3.6.1.4.1.1751.2.18.1.42 |
siteSwitchIpAddrIP Address for communication with the switch,
regardless of which cpu is primary.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.43 |
muxTcpTypeThe type of mux TCP.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.44 |
loopbackLocationIDID of the ATM Node where the loopback is to occur.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.45 |
oamDebouncingPeriodDebouncing period in milli seconds for clearing
AIS/RDI state.rw INTEGER .1.3.6.1.4.1.1751.2.18.1.46 |
svcPointToPointCallsThe total number of SVC point-to-point calls,
both legs are SVCs.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.47 |
svcPointToMultiPointCallsThe total number of SVC point-to-multipoint
calls, both legs are SVCs.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.48 |
svcPointToMultiPointPartiesThe total number of parties on SVC
point-to-multipoint calls, both legs are SVCs.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.49 |
spvcCePointToPointCallsThe total number of circuit emulation SPVC
calls.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.50 |
spvcTePointToPointCallsThe total number of terminal emulation SPVC
calls.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.51 |
spvcAtmPointToPointCallsThe total number of ATM SPVC calls.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.52 |
cgApiCirEmCirEmPvcCallsThe total number of circuit emulation to
circuit emulation calls for Sapphire API.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.53 |
cgApiCirEmAtmPvcCallsThe total number of circuit emulation to ATM
calls for Sapphire APIsrw Integer32 .1.3.6.1.4.1.1751.2.18.1.54 |
cgApiAtmAtmPvcCallsThe total number of ATM to ATM calls for
Sapphire APIsrw Integer32 .1.3.6.1.4.1.1751.2.18.1.55 |
cgApiPointToPointSvcCallsThe total number of point-to-point SVC calls
for Sapphire APIsrw Integer32 .1.3.6.1.4.1.1751.2.18.1.56 |
cgApiPointToMultiPointSvcCallsThe total number of point-to-multipoint SVC
calls for Sapphire APIsrw Integer32 .1.3.6.1.4.1.1751.2.18.1.57 |
cgApiPointToMultiPointPartiesThe total number of parties for Sapphire APIsrw Integer32 .1.3.6.1.4.1.1751.2.18.1.58 |
callContrlResAllocApply0 - not apply, 1 - apply the call control resouce
allocation modificationrw INTEGER .1.3.6.1.4.1.1751.2.18.1.59 |
callContrlResAllocUsageThe percentage of memory usage for call
control resource.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.60 |
siteFirmwarePatchNumberConstant value representing the patch number
of the patch release.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.61 |
spvcActRestartAllRestart all ATM-to-ATM,CE-to-CE,TE-to-TE,FR-to-FR active
unconnected spvc connectionsrw Enumeration .1.3.6.1.4.1.1751.2.18.1.62 |
cgSvcCutThroughOptionCut Through option for SVC calls going to CG
cgSvcAcImplicitCutThrough (1) - AC implicitly cuts
through.
cgSvcCgExplicitCutThrough (2) - CG sends explcit
PATH_ETABLISH_REQ to request AC to cut through.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.63 |
sgApiCirEmEndPointsThe total number of circuit emulation
endpoints for Sapphire API.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.64 |
sgApiAtmSvcEndPointsThe total number of ATM SVC
endpoints for Sapphire APIsrw Integer32 .1.3.6.1.4.1.1751.2.18.1.65 |
siteRemoteMgrSrcAddr1This is the source IP address used in all traps sent to remote managerrw Enumeration .1.3.6.1.4.1.1751.2.18.1.66 |
siteRemoteMgrSrcAddr2This is the source IP address used in all traps sent to remote managerrw Enumeration .1.3.6.1.4.1.1751.2.18.1.67 |
siteRemoteMgrSrcAddr3This is the source IP address used in all traps sent to remote managerrw Enumeration .1.3.6.1.4.1.1751.2.18.1.68 |
siteRemoteMgrSrcAddr4This is the source IP address used in all traps sent to remote managerrw Enumeration .1.3.6.1.4.1.1751.2.18.1.69 |
siteRemoteMgrSrcAddr5This is the source IP address used in all traps sent to remote managerrw Enumeration .1.3.6.1.4.1.1751.2.18.1.70 |
spvcFrPointToPointCallsThe total number of FR SPVC calls.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.71 |
inBandAppAtmAddressThe ATM address of the inBand applicationrw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.72 |
inBandAppAtmAddrTypeThe format of the ATM address of the inBand
applicationrw Enumeration .1.3.6.1.4.1.1751.2.18.1.73 |
atmArpServer2RemoteAtmAddressThe ATM address of the ATM ARP server when
this
switch is not the ATM ARP server and the
connection to the ATM ARP server uses SVCs.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.74 |
atmArpServer2RemoteAddrTypeThe format of the ATM address of the ATM ARP
server when this switch is not the ATM ARP
server
and the connection to the ATM ARP server uses
SVCs.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.75 |
tasmMaxAnnceDiskSpaceSpecifies the maximum disk size in MBytes
reserved for compressed announcements on
the CPU hard disk.rw INTEGER .1.3.6.1.4.1.1751.2.18.1.76 |
tasmMaxAnnceSpecifies the maximum number of tones and
announcements that can be played simultaneously.
This will depend on the number of control blocks
allocated for collecting digits and for line
tests as the memory comes from the same pool.
The tasmControlBlockResAllocUsage field will be
updated to indicate this.rw INTEGER .1.3.6.1.4.1.1751.2.18.1.77 |
tasmMaxStdTonesSpecifies the maximum number of
tones that can be played simutaneously. This field
has been obsoleted for optimisation of resources.rw INTEGER .1.3.6.1.4.1.1751.2.18.1.78 |
tasmMemoryActionSpecifies the action to be performed
on the memory in the TASM card used for
storing announcements.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.79 |
tasAnnceTableTable of announcements for the Tone
Announcement server . SEQUENCE OF TasAnnceEntry .1.3.6.1.4.1.1751.2.18.1.80 |
tasAnnceEntryRow definition for Tone Announcement server
table announcement entries. TasAnnceEntry .1.3.6.1.4.1.1751.2.18.1.80.1 |
tasAnnceIdAnnouncement ID. INTEGER .1.3.6.1.4.1.1751.2.18.1.80.1.1 |
tasAnnceTypeThe type of this announcement:
voice indicates it is a pure voice
announcement file.
toneVoice indicates it is a file with tones
at the beginning followed by voice.
userTones indicates it is a file with purely
user generated tones.
music indicates it is a file with pure music.
musicVoice indicates it is a file with music
at the beginning followed by voice.
toneMusic indicates it is a file with tones
at the beginning followed by music.ro Enumeration .1.3.6.1.4.1.1751.2.18.1.80.1.2 |
tasAnnceCmprsTypeThe type of compression used for
storing this announcement:
compress8k indicates 8k compression algorithm
should be used. compress16k indicates 16k
compression algorithm should be used.
compress32k indicates 32k compression algorithm
should be used.ro Enumeration .1.3.6.1.4.1.1751.2.18.1.80.1.3 |
tasAnnceValidIndicates the condition of this announcement,
whether it is good, it is stored using an older
compression algorithm, or it is corrupted.ro Enumeration .1.3.6.1.4.1.1751.2.18.1.80.1.4 |
tasAnnceDescriptionDescription for this announcement.ro DisplayString .1.3.6.1.4.1.1751.2.18.1.80.1.5 |
tasToneConfigTableTable of standard physical tone attributes SEQUENCE OF TasToneConfigEntry .1.3.6.1.4.1.1751.2.18.1.81 |
tasToneConfigEntryRow definition for TASM announcement entries. TasToneConfigEntry .1.3.6.1.4.1.1751.2.18.1.81.1 |
tasToneIdTone ID. INTEGER .1.3.6.1.4.1.1751.2.18.1.81.1.1 |
tasToneTypeThe type of this standard tone.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.81.1.2 |
tasToneFirstFreqThe first frequency value for this tone.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.81.1.3 |
tasToneSecondFreqThe second frequency value for this tone.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.81.1.4 |
tasToneThirdFreqThe third frequency value for this tone.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.81.1.5 |
tasToneOnTimeThe on time in the tone duty cycle.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.81.1.6 |
tasToneOffTimeThe off time in the tone duty cycle.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.81.1.7 |
tasToneLevelThe level of this tone in dBm.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.81.1.8 |
atmArpServerAtmAddrThe ATM address of the ATM ARP server when this
switch is configured as the ATM ARP server .rw OCTET STRING .1.3.6.1.4.1.1751.2.18.1.82 |
atmArpServerAddrTypeThe format of the ATM address of the ATM ARP
server when this switch is configured as the
ATM ARP server.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.83 |
spvcPointToMultiPointCallsThe total number of SPVC point-to-multipoint
callsrw Integer32 .1.3.6.1.4.1.1751.2.18.1.84 |
spvcPointToMultiPointPartiesThe total number of parties on SPVC
point-to-multipoint calls.rw Integer32 .1.3.6.1.4.1.1751.2.18.1.85 |
consoleIPAddr1console IP Address, where TRAP will be
sent.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.86 |
consoleIPAddr2console IP Address, where TRAP will be
sent.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.87 |
consoleIPAddr3console IP Address, where TRAP will be
sent.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.88 |
consolePort1port number on host where TRAP will be
sentrw INTEGER .1.3.6.1.4.1.1751.2.18.1.89 |
consolePort2port number on host where TRAP will be
sentrw INTEGER .1.3.6.1.4.1.1751.2.18.1.90 |
consolePort3port number on host where TRAP will be
sentrw INTEGER .1.3.6.1.4.1.1751.2.18.1.91 |
featureTableTable of features to be turned on/off SEQUENCE OF FeatureEntry .1.3.6.1.4.1.1751.2.18.1.92 |
featureEntryRow definition for feature table FeatureEntry .1.3.6.1.4.1.1751.2.18.1.92.1 |
featureIdfeature ID. Enumeration .1.3.6.1.4.1.1751.2.18.1.92.1.1 |
featureStaticMemMinimum memory required to run this featurero Integer32 .1.3.6.1.4.1.1751.2.18.1.92.1.2 |
featureDesiredStatusTo enable / disable this featurerw Enumeration .1.3.6.1.4.1.1751.2.18.1.92.1.3 |
featureCurrentStatusThis feature is enabled / disabledro Enumeration .1.3.6.1.4.1.1751.2.18.1.92.1.4 |
mediaGatewayControlTypeChoose to use H.248 protocol or
sapphire protocolrw Enumeration .1.3.6.1.4.1.1751.2.18.1.93 |
dspResourceTableTable of DSP resource usage for the whole system. SEQUENCE OF DspResourceEntry .1.3.6.1.4.1.1751.2.18.1.94 |
dspResourceEntryRow definition for DSP resource usage
table entries. DspResourceEntry .1.3.6.1.4.1.1751.2.18.1.94.1 |
dspResourceIdDSP resource type enumerations. The algoSets describe
the mode of the DSP card. Each mode corresponds to a
set of algorithms supported by the IO card.
Aal modes describe the aal type used.
algoSet1-aal2-non-multiplexed:
resource type for algoSet1 DSP mode and
non-multiplexed aal2 AAL mode.
algoSet1-aal2-std :
resource type for algoSet1 DSP mode and standard
aal2 AAL mode.
algoSet2-aal2-non-multiplexed:
resource type for algoSet2 DSP mode and
non-multiplexed aal2 AAL mode.aal2 AAL mode.
algoSet2-aal2-std:
resource type for algoSet2 DSP mode and standard
aal2 AAL mode.
algoSet3-aal2-non-multiplexed:
resource type for algoSet3 DSP mode and
non-multiplexed aal2 AAL mode.
algoSet3-aal2-std:
resource type for algoSet3 DSP mode and standard
aal2 AAL mode.
algoSet5-aal1:
resource type for algoSet5 DSP mode and
aal1 AAL mode.
algoSet6-aal2-std:
resource type for algoSet6 DSP mode and standard
aal2 AAL mode.
tone-annce-cas:
resource type for the tone announcement interface
and CAS mode of the TASM card.
tone-annce-tas:
resource type for the tone announcement interface
and TAS mode of the TASM card. Enumeration .1.3.6.1.4.1.1751.2.18.1.94.1.1 |
dspResourceAvailThe available DSP resource counts how many
connections can be made using this available
DSP resource type in the system.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.94.1.2 |
dspResourceUsedThe used DSP resource counts how many
connections are already made using this
available DSP resource type in the system.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.94.1.3 |
dspResourceUsedFailedThe used but failed DSP resource counts
how many connections are already made
using currently failed DSP resource type in
the system.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.94.1.4 |
dspResourceAvailFailedThe available but failed DSP resource counts
how many connections can be made if using
currently failed DSP resource type in the
system.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.94.1.5 |
tasmMaxDigitControlBlocksSpecifies the maximum number of digit collection
that can be initiated simultaneously. This will
depend on the number of control blocks allocated
for playing tones and announcements and for line
tests as the memory comes from the same pool.
The tasmControlBlockResAllocUsage field will be
updated to indicate this .rw INTEGER .1.3.6.1.4.1.1751.2.18.1.95 |
tasmMaxTestControlBlocksSpecifies the maximum number of TDM line tests
that can be initiated simultaneously. This will
depend on the number of control blocks allocated
for playing tones and announcements and for digit
collection as the memory comes from the same pool.
The tasmControlBlockResAllocUsage field will be
updated to indicate this.rw INTEGER .1.3.6.1.4.1.1751.2.18.1.96 |
tasmMaxMemResvdSpecifies the maximum amount of memory
in megabytes reserved for TASM.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.97 |
tasmControlBlockResAllocUsageThe percentage of memory usage for tones,
announcements, digit collection and line tests
control blocks.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.98 |
tasmAnnceCacheMemResAllocUsageThe percentage of memory usage for caching
announcements in memory. Everytime an announcement
is compressed this field will be updated to reflect
the cache memory that will be taken up by this
announcement. Once this field shows a 100 percent
usage it is an indication to the user that any
additional announcement will cause the system to
thrash as it clears an announcement in cache to
make room for the new announcement.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.99 |
siteAlternateGatewayAddrAlternate ip address of gateway to access the site
(switch),Can be used only over the InBand PVC
connection when the OAM is enabled on InBand PVCsrw IpAddress .1.3.6.1.4.1.1751.2.18.1.100 |
ipThrottlingConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.1.101 |
ipThrottlingFeatureStatusCPU card IP throttling feature: off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.1.101.1 |
ipThrottlingAllowedInFrameRateCPU card IP throttling: allowed input
frames per secondrw INTEGER .1.3.6.1.4.1.1751.2.18.1.101.2 |
ipThrottlingLeakyBucketSizeCPU card IP throttling: the size of leaky
bucketrw INTEGER .1.3.6.1.4.1.1751.2.18.1.101.3 |
ipThrottlingStatsOdometerTimerCPU card IP throttling: Number of seconds
since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.101.4 |
ipThrottlingStatsOdometerResetCPU card IP throttling: Odometer reset
button.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.101.5 |
ipThrottlingInPacketsCPU card IP throttling: the total number of
input packets from both Ethernet port and
In-band-mgmt of the CPU card.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.101.6 |
ipThrottlingInPacketsPassedEiCPU card IP throttling: the number of input
packets passed through the Ethernet port
of the CPU card.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.101.7 |
ipThrottlingInPacketsDroppedEiCPU card IP throttling: the number of input
packets dropped from the Ethernet port of
the CPU card.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.101.8 |
ipThrottlingInPacketsPassedIBMCPU card IP throttling: the number of input
packets passed from the In-Band-Management
of the CPU card.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.101.9 |
ipThrottlingInPacketsDroppedIBMCPU card IP throttling: the number of input
packets dropped from the In-Band-Management of
the CPU card.ro Integer32 .1.3.6.1.4.1.1751.2.18.1.101.10 |
csSapphireInterfaceAddressThe IP address to be specified as the source
address in the TCP connect message that is
sent to the SoftSwitch running as server and PSAX
running as client.rw IpAddress .1.3.6.1.4.1.1751.2.18.1.102 |
trapActivationTableTable of traps be turned on/off SEQUENCE OF TrapActivationEntry .1.3.6.1.4.1.1751.2.18.1.103 |
trapActivationEntryRow definition for trapActivation table TrapActivationEntry .1.3.6.1.4.1.1751.2.18.1.103.1 |
trapGroupIdtrap group ID. Enumeration .1.3.6.1.4.1.1751.2.18.1.103.1.1 |
trapIndextrap index in each group. Integer32 .1.3.6.1.4.1.1751.2.18.1.103.1.2 |
trapActivationStatusactivated: trap message activated.
deactivated: trap message deactivated.
permanently-activated: trap message can not be
deactivated.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.103.1.3 |
trapNamesName of the trapro DisplayString .1.3.6.1.4.1.1751.2.18.1.103.1.4 |
resetActionset-all-active: set all trap active one group.
set-all-deactive: set all trap deactive in a group.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.103.1.5 |
spvcGlobalPrioritySchemeFlag indicating whether priority scheme should
be supported across SPVCs and SPVC-trunks.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.104 |
spvcPrioritySchemeFlag indicating whether priority scheme should
be supported in SPVCs.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.105 |
spvcTrunkingPrioritySchemeFlag indicating whether priority scheme should
be supported in SPVC-trunks.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.106 |
atmTrunkVccsThe total number of ATM Trunk VCCs (including SigVccs
and Bearer Vccs).rw Integer32 .1.3.6.1.4.1.1751.2.18.1.107 |
atmTrunkNarrowBandCallsThe total number of ATM Trunking Narrow Band Calls
supportedrw Integer32 .1.3.6.1.4.1.1751.2.18.1.108 |
dspResourceFeatureConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.1.109 |
dspReroutingFeatureDsp2 Rerouting Feature.This is used to
enable or disable rerouting of connections
when a dsp chip or card fails.rw Enumeration .1.3.6.1.4.1.1751.2.18.1.109.1 |
equipConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.2 |
cardTableTable of card configuration data SEQUENCE OF CardEntry .1.3.6.1.4.1.1751.2.18.2.1 |
cardEntryRow definition for ac120 card CardEntry .1.3.6.1.4.1.1751.2.18.2.1.1 |
cardSlotPhysical slot location. Valid range is a number
between 1 and 24. INTEGER .1.3.6.1.4.1.1751.2.18.2.1.1.1 |
cardTypeType of card in a physical slot. A specific type
of card is associated with each number.
none(1) no board present
taxi(2) Taxi
oC-3c(3) OC3
dS3-ATM(4) DS3 ATM
dS1-CE(5) DS1 circuit emulation
dS1-ATM(6) DS1 ATM
e1-CE(7) E1 circuit emulation
e3-ATM(8) E3 ATM
highSpeed(9) High Speed Serial
mSerial(10) Multi Serial
dSP1(11) DSP
tWStation(12) Two Wire Station
tWOffice(13) Two Wire Office
cPU(14) Central Processor Unit
stratum(15) Stratum
pwrSupply(16) Power Supply
protectionCard(17) protection card
e1-ATM(18) E1 ATM
ethernet(19) Ethernet
enhDS1(20) Enhanced DS1
enhE1(21) Enhanced E1
oC-3cMMAQ(22) OC3 Multimode Aqueman
oC-3cMMTS(23) OC3 Multimode Traffic Shaping
oC-3cSMAQ(24) OC3 Singlemode Aqueman
oC-3cSMTS(25) OC3 Singlemode Traffic Shaping
sTM-1SMAQ(26) STM1 Singlemode Aqueman
sTM-1SMTS(27) STM1 Singlemode Traffic Shaping
sTM-1MMAQ(28) STM1 Multimode Aqueman
sTM-1MMTS(29) STM1 Multimode Traffic Shaping
dS3-FR(30) DS3 Frame Relay
dSP2A(31) DSP2 card revision 2A
dS1-IMA(32) DS1 Inverse Multiplexing over
ATM (IMA) I/O card
e1-IMA(33) E1 IMA
alarm(34) alarm card
dSP2B(35) DSP card revision 2B
aps-OC-3cSM(36) Automatic Protection Switching
OC3 Single Mode
aps-OC-3cMM(37) Automatic Protection Switching
OC3 Multi Mode
msp-STM-1SM(38) Multi Switch Protection STM1
Singemode
msp-STM-1MM(39) Multi Switch Protection STM1
Multimode
cH-DS3(40) Channelized DS3
cH-STS1(41) Channelized STS1
rT-S(42) Route Server
cC-Server(43) Continuity Check Server
hD-E1(44) High Density E1
hD-DS1(45) High Density DS1
dS3-IMA(46) DS3 IMA
dSP2C(47) DSP card revision 2C
tasm(48) Tone Announcement Service Module
mD-DS1(49) Medium Density DS1
quadSerial(50) Quad Serial
mD-DS1-IMA(51) Medium Density DS1 IMA
mD-E1-IMA(52) Medium Density E1 IMA
hD-DS1-IMA(53) High Density DS1 IMA
hD-E1-IMA(54) High Density E1 IMA
chDS3STS1-3P(55) 3-port channelized DS3 STS1
unstDS3E3-3P(56) 3-port unstructured DS3 E3
dS3E3-ATM-3P(57) 3-port DS3 E3 ATM
oC12c-STM4-MM(58) OC12 STM4 Multimode
oC12c-STM4-SM(59) OC12 STM4 Singlemode
dSP2D(60) DSP card revision 2D
ethernet-4P(61) 4-port Ethernet
chDS3STS1-3P-Prot(62) 3-port channelized DS3 STS1
protection
alarm-fan(63) alarm fan card
dS1-Nx64CAS(64) DS1 card supporting N x 64 CASro Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.2 |
cardProtectionStatusCurrent protection status of the card:
none if the card is un-protected; protected
if it is under the protection of another card;
wrongType if the card types of protection card
and protected card are different.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.3 |
cardOperStatusCurrent operational status of the card.
For I/O card, it is primary if configured,
it is unknown if unconfigured, or removed.
For CPU, it is primary if the CPU is master
CPU, or standby if the CPU is slave CPU.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.4 |
cardAdminStatusadministrative statusrw Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.5 |
cardAlarmStatuslast alarm occurredro Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.6 |
cardCleiCodeCLEI codero DisplayString .1.3.6.1.4.1.1751.2.18.2.1.1.7 |
cardRevisionCard Revision numberro Integer32 .1.3.6.1.4.1.1751.2.18.2.1.1.8 |
cardSerialNumberSerial Numberro DisplayString .1.3.6.1.4.1.1751.2.18.2.1.1.9 |
cardOperatingModeMode of operation for a card. This is
applicable
to those card types which can be configured in a dual mode.
e.g. unstDS3E3-3P can be operational as either a 3 port
DS3 or
E3 card. All ports on the card will be of the same type
depending on the card's operating mode.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.10 |
protectionConfigModeProtection Configuration Mode of a Card
unprotected: Card is not in protection or protected state
protection: Card is in protection state
working: Card is in protected/working state and this
state is read only and cannot be set by the userrw Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.11 |
protectionStatusProtection Status of a card. Inservice and
OutofService indicates if the card has failed or
still operational.
Active or Standby state indicates if it is
carrying active traffic or not.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.1.1.12 |
protectionSlotIf Protection Config Mode is Working then
this field gives the protection slot.ro INTEGER .1.3.6.1.4.1.1751.2.18.2.1.1.13 |
taxiPortConfigTableTable of common physical Port attributes SEQUENCE OF TaxiPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.2 |
taxiPortConfigEntryRow definition for common physical
port attributes TaxiPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.2.1 |
taxiPortIdinterface index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.2.1.1 |
taxiPortTypetaxi typerw Enumeration .1.3.6.1.4.1.1751.2.18.2.2.1.2 |
taxiLineStatustaxi line status:
1: NoAlarm
2: Loss of Signalro INTEGER .1.3.6.1.4.1.1751.2.18.2.2.1.3 |
taxiOutputTransferRateUser selectable parameter which allows the
outgoing rate of the port to be reduced to 50%
taxi, halfRate, only on AQueMan.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.2.1.4 |
ds3PortConfigTableTable of ds3 specific port attributes SEQUENCE OF Ds3PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.3 |
ds3PortConfigEntryRow definition for ds3 specific
port attributes Ds3PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.3.1 |
ds3PortIdslot/port: SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.3.1.1 |
ds3LineTypeThis variable indicates the variety of DS3 C-bit
implementing this interface. The type of
interface affects the interpretation of the
usage and error statistics.
The rate of DS3 is 44.736 Mbps.
The dsx3ClearChannel value means that
the C-bits are not used except for
sending/receiving AIS.
The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3CbitParity ANSI T1.107a-1989
dsx3ClearChannel ANSI T1.102-1987.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.2 |
ds3LineCodingThis variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
ds3B3ZS refers to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.3 |
ds3LoopbackConfigThis variable represents the loopback
configuration of the DS3 interface.
See above diagrams for explanations of loops.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.4 |
ds3TransmitClockSourceThe source of Tranmit Clock.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.
'localTiming' indicates that a local clock
source is used.
'cardFreeRun' indicates that a local oscillator on
the I/O card is used as the transmit clock.
'adaptiveTiming' indicates that the adaptive clocking
mechanism is usedrw Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.5 |
ds3LineStatusds3 line status:
1: dsx3NoAlarm: No alarm present
2: dsx3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication
4: dsx3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication
8: dsx3RcvAIS: Receiving AIS failure state
16: dsx3XmitAIS: Transmitting AIS failure statue
32: dsx3LOF: Receiving LOF failure state
64: dsx3LOS: Reveiving LOS failure state
128: dsx3LoopbackState: Looping the received signal
256: dsx3RcvTestCode: Receiving a Test Pattern
512: dsx3OtherFailure: any line status not defined
1024: dsx3RcvRmtAIS:
2048: dsx3RcvRmtOOF:
4096: dsx3RcvRmtLOS:
8192: dsx3RcvRmtIdle:
16384: dsx3RmtLoopback: Far end remote loopbackro INTEGER .1.3.6.1.4.1.1751.2.18.2.3.1.6 |
ds3LineBuildOutds3 line build outrw Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.7 |
ds3LineScrambleds3 line scramblerw Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.8 |
ds3CellMappingds3 cell mapping methodrw Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.9 |
ds3SendCodeThis variable indicates what type of code is being
sent across the ds3 interface by the device. The
values mean:
'noCode' - sending looped or normal data
'lineLoopCode' - sending a request for a line
loopback
'deactivateCode' - sending a loopback deactivation
request
'testPattern' - sending a test patternrw Enumeration .1.3.6.1.4.1.1751.2.18.2.3.1.10 |
ds3OutputTxRateThe ability to adjust the bandwidth of DS3 in tx
direction. The adjustable DS3 bandwidth
will support 1% increments.rw INTEGER .1.3.6.1.4.1.1751.2.18.2.3.1.11 |
msPortConfigTableTable of multi-serial card's port attributes SEQUENCE OF MsPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.4 |
msPortConfigEntryRow definition for multi-serial port attributes MsPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.4.1 |
msPortIdslot/port: SSPP IntfIndex .1.3.6.1.4.1.1751.2.18.2.4.1.1 |
msLineCodingLine Coding.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.2 |
msBaudRatebaud rate is determined by
multiplying this number by the
msBaudRateMultiplierrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.3 |
msProtocolprotocol type for serial portrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.4 |
msEquipmentTypeEquipment typerw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.5 |
msRs232XmitModetransmit mode for rs232 DTE/DCE serial portrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.6 |
msRs232Parityparity for rs232 DTE/DCE serial portrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.7 |
msRs232DataBitsdata bits for rs232 DTE/DCE serial portrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.8 |
msRs232StopBitsstop bits for rs232 DTE/DCE serial portrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.9 |
msTxDataClkSrcForDteTransmit data clock source for DTE,
externalTx in is not valid for rs232.
This field is ignored if the local side is DCE.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.10 |
msTxDataClkSrcForDceTransmit data clock source for DCE
localTiming: a local clock source is used. (e.g., from
backplane (stratum)
loopTiming: from remote
This field is ignored if the local side is DTErw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.11 |
msRxDataClkSrcForDceReceive data clock source for DCE
localTiming: a local clock source is used. (e.g., from
backplane (stratum)
loopTiming: from remote
This field is ignored if the local side is DTErw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.12 |
msRxClkPolarityWhether or not to reverse the receive clockrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.13 |
msTxClkPolarityWhether or not to reverse the transmit clockrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.14 |
msKgResyncTurn KG resync on/offrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.15 |
msHandshakeMultiserial Module handshake:
observed : used with AAL1 to monitor
RTS/CTS exchange.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.16 |
msSpeedAdaptionThe state of allowing speed adaptionrw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.17 |
msBitStuffingWhen msBitStuffing is enabled,
CAC throughput is (1 + 1/7) user throughtput.
Otherwise the CAC throughput is the same as the user throughput.
msBitStuffing can only be enabled for circuit emulation interfaces.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.18 |
msLineStatusline status on the port:
The msLineStatus is a bit map representation.
It can represent multiple failures (alarms)
if supported by the card.
NoAlarm should be set if and only if
no other flag is set.
The various bit positions are:
1: NoAlarm
2: Loss of Signalro INTEGER .1.3.6.1.4.1.1751.2.18.2.4.1.19 |
msRxDataPolarityWhether or not to reverse the receive datarw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.20 |
msTxDataPolarityWhether or not to reverse the transmit datarw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.21 |
msLoopbackConfigThis variable represents the loopback
configuration of the Serial port.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.22 |
msLOSDetectionState of detection of LOS by IO card.
LOS detection is always enabled when msBitStuffing is enabled.
When the interface is not circuit emulation, the IO card does not report any LOS.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.4.1.23 |
ds1PortConfigTableTable of ds1 specific port attributes SEQUENCE OF Ds1PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.5 |
ds1PortConfigEntryRow definition for ds1 specific
port attributes Ds1PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.5.1 |
ds1PortIdinterface index - slot/port: SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.5.1.1 |
ds1Channelizationds1 interface typerw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.2 |
ds1LineTypeds1 interface typerw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.3 |
ds1LineCodingds1 interface typerw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.4 |
ds1LoopbackConfigThis variable represents the loopback
configuration of the ds1 interfacerw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.5 |
ds1TransmitClockSourceds1 timing sourcerw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.6 |
ds1LineBuildOutds1 line build outrw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.7 |
ds1LineStatusThis variable indicates the Line Status of the
interface. It contains loopback, failure, re-
ceived 'alarm' and transmitted 'alarm' infor-
mation.
The dsx1LineStatus is a bit map represented
as a sum, therefore, it can represent multiple
failures (alarms) and a LoopbackState
simultaneously.
ds1NoAlarm should be set if and only if no other
flag is set.
If the ds1LoopbackState bit is set, the loopbak
in effect can be determined from the
ds1LoopbackConfig object.
The various bit positions are:
1: dsx1NoAlarm: No Alarm Present
2: dsx1RcvFarEndLOF: Far end LOF (a.k.a., Yellow
Alarm)
4: dsx1XmtFarEndLOF: Near end sending LOF Indication
8: dsx1RcvAIS: Far end sending AIS
16: dsx1XmtAIS: Near end sending AIS
32: dsx1LossOfFrame: Near end LOF (a.k.a., Red Alarm)
64: dsx1LossOfSignal: Near end Loss Of Signal
128: dsx1LoopbackState: Near end is looped
256: dsx1T16AIS: E1 TS16 AIS
512: dsx1RcvFarEndLOMF: Far End Sending TS16 LOMF
1024: dsx1XmtFarEndLOMF: Near End Sending TS16 LOMF
2048: dsx1RcvTestCode: Near End detects a test code
4096: dsx1OtherFailure: any line status not defined
here
8192: dsx1RmtLoopback: Far end loopbackro INTEGER .1.3.6.1.4.1.1751.2.18.2.5.1.8 |
ds1EnhanceFeatureSet1To enable/disable a proprietary ab signaling
scheme, it applies to all DS0s in the port. No
individual DS0 signaling can be configured under
this scheme.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.10 |
ds1DataTransferTypeDS1 data transfer type is only applicable in
Circuit Emulation where unstructured CE packets
entire T1 frame including the F-bit into the AAL1
for data tranfer, whereas, the structured CE
packets the entire T1 frame except the F-bit.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.11 |
ds1OamInterworkingTypeSpecifies whether the interworking is done
by trunk conditioning or unframed1srw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.12 |
ds1ConnGatewayFeatureTo enable/disable connection gateway
(Sapphire) API.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.14 |
ds1InLineCodeTo select and support the inlinecode option
in either ANSI or DS1_ANI
(ANI: Access Network Interface)rw Enumeration .1.3.6.1.4.1.1751.2.18.2.5.1.15 |
oc3PortConfigTableTable of common physical Port attributes SEQUENCE OF Oc3PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.6 |
oc3PortConfigEntryRow definition for common physical
port attributes Oc3PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.6.1 |
oc3PortIdinterface index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.6.1.1 |
oc3LoopbackConfigThis variable represents the loopback
configuration of the OC3 interface
See above diagrams for explanations of loops.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.6.1.2 |
oc3TransmitClockSourceThe source of Tranmit Clock.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.
'localTiming' indicates that a local clock
source is used.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.6.1.3 |
oc3LineStatusoc3 line status -
1: oc3NoAlarm: No alarm present
2: oc3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication
4: oc3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication
8: oc3RcvAIS: Receiving AIS failure state
16: oc3XmitAIS: Transmitting AIS failure statue
32: oc3LOF: Receiving LOF failure state
64: oc3LOS: Reveiving LOS failure state
128: oc3LoopbackState: Looping the received signal
256: oc3RcvTestCode: Receiving a Test Pattern
512: oc3OtherFailure: any line status not defined
1024: oc3LCD: Receiving Loss Of Cell Delineation
2048: oc3LRDI: Receiving Line RDI failure state
4096: oc3PRDI: Receiving Path RDI failure statero INTEGER .1.3.6.1.4.1.1751.2.18.2.6.1.4 |
oc3OutputTransferRateUser selectable parameter which allows the
outgoing rate of the port to be reduced to 50%
oc3, halfRate, only on AQueMan.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.6.1.5 |
oc3APSConfigurationIndicates whether APS is configured for this
port .rw Enumeration .1.3.6.1.4.1.1751.2.18.2.6.1.6 |
twoWireSourcePortConfigTableTable of common physical Port attributes SEQUENCE OF TwoWireSourcePortConfigEntry .1.3.6.1.4.1.1751.2.18.2.7 |
twoWireSourcePortConfigEntryRow definition for common physical
port attributes TwoWireSourcePortConfigEntry .1.3.6.1.4.1.1751.2.18.2.7.1 |
twoWireSourcePortIdinterface index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.7.1.1 |
twoWireSourceLoopDetectionThis field selects terminal equipment loop circuit
detection mode.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.7.1.2 |
twoWireSourceDialModeThis field configures twoWireSource card to
support communication terminal equipment.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.7.1.3 |
twoWireSourceLoopBackConfigConfiguration of 2W Source LoopBack.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.7.1.4 |
twoWireSourceLineStatustwoWireSource line status:
1: NoAlarm: No alarm present
2: SignalingFailureState
4: FacilityLoopBack
8: Maintenance
16: Out Of Service
32: OtherFailurero INTEGER .1.3.6.1.4.1.1751.2.18.2.7.1.5 |
twoWireSourceSignalingBitsThis field selects the signaling bits as seen in
DS1 signal, ab or abcd.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.7.1.6 |
twoWireSourceRingCadenceThis field selects ring On/Off pattern.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.7.1.7 |
twoWireSourceSignalingStateThis field reflects the current signaling state.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.7.1.8 |
twoWireSourceTestModeThis field selects line test mode. For normal
operation, this field should be OFF.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.7.1.9 |
highSpeedPortConfigTableTable of common physical Port attributes SEQUENCE OF HighSpeedPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.8 |
highSpeedPortConfigEntryRow definition for common physical
port attributes HighSpeedPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.8.1 |
highSpeedPortIdinterface index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.8.1.1 |
highSpeedPortInputRatePort input raterw Integer32 .1.3.6.1.4.1.1751.2.18.2.8.1.2 |
highSpeedPortOutputRatePort output raterw Integer32 .1.3.6.1.4.1.1751.2.18.2.8.1.3 |
dspPortConfigTableTable of common physical Port attributes SEQUENCE OF DspPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.9 |
dspPortConfigEntryRow definition for common physical
port attributes DspPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.9.1 |
dspPortIdinterface index - SSPPro Integer32 .1.3.6.1.4.1.1751.2.18.2.9.1.1 |
twoWireSinkPortConfigTableTable of common physical Port attributes SEQUENCE OF TwoWireSinkPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.10 |
twoWireSinkPortConfigEntryRow definition for common physical
port attributes TwoWireSinkPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.10.1 |
twoWireSinkPortIdinterface index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.10.1.1 |
twoWireSinkLoopDetectionTypes of loop detection.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.10.1.2 |
twoWireSinkDialModeThis field selects subscribed dial mode.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.10.1.3 |
twoWireSinkLineStatustwoWireSink line status:
1: NoAlarm: No alarm present
2: SignalingFailureState
4: FacilityLoopBack
8: Maintenance
16: Out Of Service
32: OtherFailurero INTEGER .1.3.6.1.4.1.1751.2.18.2.10.1.4 |
twoWireSinkSignalingBitsThis field selects the signaling bits as seen in
DS1 signal, ab or abcd.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.10.1.5 |
twoWireSinkSignalingStateThis field reflects the current signaling state.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.10.1.6 |
twoWireSinkTestModeThis field selects line test mode. For normal
operation, this field should be OFF.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.10.1.7 |
e3PortConfigTableTable of e3 specific port attributes SEQUENCE OF E3PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.11 |
e3PortConfigEntryRow definition for e3 specific
port attributes E3PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.11.1 |
e3PortIdslot/port: SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.11.1.1 |
e3LineTypeThis variable indicates the basic frame structure
supported in this E3 port. The rate of E3 is
34.368 Mbps.
TITLE: SPECIFICATION:
G.832 ITU-T G.832 1993.
G.751 ITU-T G.751 1998rw Enumeration .1.3.6.1.4.1.1751.2.18.2.11.1.2 |
e3LineCodingThe line code supported for the E3 port.
The High Density Bipolar of order 3 (hdb3)
as specified in section 8.1 of ITU-T G.703.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.11.1.3 |
e3LoopbackConfigThis variable represents the loopback
configuration of the E3 interface.
See above diagrams for explanations of loops.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.11.1.4 |
e3TransmitClockSourceThe source of Tranmit Clock.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.
'localTiming' indicates that a local clock
source is used.
'adaptiveTiming' indicates that the adaptive clocking
mechanism is used.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.11.1.5 |
e3LineStatuse3 line status:
1: e3NoAlarm: No alarm present
2: e3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication
4: e3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication
8: e3RcvAIS: Receiving AIS failure state
16: e3XmitAIS: Transmitting AIS failure statue
32: e3LOF: Receiving LOF failure state
64: e3LOS: Reveiving LOS failure state
128: e3LoopbackState: Looping the received signal
256: e3RcvTestCode: Receiving a Test Pattern
512: e3OtherFailure: any line status not definedro INTEGER .1.3.6.1.4.1.1751.2.18.2.11.1.6 |
e3LineBuildOute3 line build outro Enumeration .1.3.6.1.4.1.1751.2.18.2.11.1.7 |
e3LineScramblee3 line scramblerw Enumeration .1.3.6.1.4.1.1751.2.18.2.11.1.8 |
e3CellMappinge3 cell mapping methodrw Enumeration .1.3.6.1.4.1.1751.2.18.2.11.1.9 |
e1PortConfigTableTable of e1 specific port attributes SEQUENCE OF E1PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.12 |
e1PortConfigEntryRow definition for e1 specific port attributes E1PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.12.1 |
e1PortIdinterface index - slot/port: SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.12.1.1 |
e1Channelizatione1 interface typerw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.2 |
e1LineTypeE1 interface type.
The rate of E1 is 2.048 Mbpsro Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.3 |
e1LineCodinge1 interface typero Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.4 |
e1LoopbackConfigThis variable represents the loopback
configuration of the e1 interface
See above diagrams for explanations of loops.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.5 |
e1TransmitClockSourcee1 timing sourcerw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.6 |
e1LineNationalBitse1 line country specific coderw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.7 |
e1LineStatusThis variable indicates the Line Status of the
interface. It contains loopback, failure, re-
ceived 'alarm' and transmitted 'alarm' infor-
mation.
The e1LineStatus is a bit map represented
as a sum, therefore, it can represent multiple
failures (alarms) and a LoopbackState
simultaneously.
e1NoAlarm should be set if and only if no other
flag is set.
If the e1LoopbackState bit is set, the loopback
in effect can be determined from the
e1LoopbackConfig object.
The various bit positions are:
1: e1NoAlarm: No Alarm Present
2: e1RcvFarEndLOF: Far end LOF (a.k.a., Yellow
Alarm)
4: e1XmtFarEndLOF: Near end sending LOF Indication
8: e1RcvAIS: Far end sending AIS
16: e1XmtAIS: Near end sending AIS
32: e1LossOfFrame: Near end LOF (a.k.a., Red Alarm)
64: e1LossOfSignal: Near end Loss Of Signal
128: e1LoopbackState: Near end is looped
256: e1T16AIS: E1 TS16 AIS
512: e1RcvFarEndLOMF: Far End Sending TS16 LOMF
1024: e1XmtFarEndLOMF: Near End Sending TS16 LOMF
2048: e1RcvTestCode: Near End detects a test code
4096: e1OtherFailure: any line status not defined
herero INTEGER .1.3.6.1.4.1.1751.2.18.2.12.1.8 |
e1TS16Time slot 16 is configurable for channel
associated signaling (CAS) or data.
cas: 'ABCD' signaling will be extracted in time
slot 16 if channel is configured for circuit
emulation.
ccs: time slot 16 will not carry any e1 channel
signaling information, instead, it will be used
for data.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.10 |
e1DataTransferTypeE1 data transfer type is only applicable in
Circuit Emulation where unstructured CE packets
entire T1 frame including the F-bit into the AAL1
for data tranfer, whereas, the structured CE
packets the entire E1 frame except the Frame
alignment signal channel.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.11 |
e1CRC4Enable or disable transmission of CRC4 bits on
bit 1 of each frame.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.12 |
e1OamInterworkingTypeSpecifies whether the interworking is done
by trunk conditioning or unframed1srw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.13 |
e1EnhanceFeatureSet1To enable/disable a proprietary ab signaling
scheme, it applies to all DS0s in the port.
No individual DS0 signaling can be
configured under the scheme.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.14 |
e1ConnGatewayFeatureTo enable/disable connection gateway
(Sapphire) API.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.12.1.15 |
ethernetPortConfigTableTable of common physical Port attributes SEQUENCE OF EthernetPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.13 |
ethernetPortConfigEntryRow definition for common physical
port attributes EthernetPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.13.1 |
ethernetPortIdinterface index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.13.1.1 |
ethernetLinkTypeThe type of port can either be set to 10baseT or
100baseT for the first port on the ethernet card.
The other ports can only be set to 10baseT. The
Auto mode will detect what LAN speed the port is
connected to.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.13.1.2 |
ethernetPhysicalAddrThe MAC address used by this bridge when it must
be referred to in a unique fashion. It is
recommended that this be the numerically smallest
MAC address of all ports that belong to this
bridge. However it is only required to be unique.
When concatenated with dot1dSprPriority a unique
Bridgeidentifier is formed which is used in the
Spanning Tree Protocol.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.2.13.1.3 |
ethernetLineStatusethernet line status:
1: Down
2: 10baseT-FullDuplex
4: 10baseT-HalfDuplex
8: 100baseT-FullDuplex
16: 100baseT-HalfDuplexro INTEGER .1.3.6.1.4.1.1751.2.18.2.13.1.4 |
ethernetDuplexModeSet the port to either be in full or half duplex.
You can also set the port to auto detect the mode
it is connected to.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.13.1.5 |
dsp2PortConfigTableTable of common physical Port attributes SEQUENCE OF Dsp2PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.14 |
dsp2PortConfigEntryRow definition for common physical
port attributes Dsp2PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.14.1 |
dsp2PortIdinterface index - SSPPro Integer32 .1.3.6.1.4.1.1751.2.18.2.14.1.1 |
imaPortConfigTableTable used for the IMA virtual port on cards that
have physical interfaces configured as atmIma.
Corresponds to port 7 on DS1 and E1. SEQUENCE OF ImaPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.15 |
imaPortConfigEntryRow definition for ima specific
port attributes ImaPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.15.1 |
imaPortIdinterface index - slot/port: SSPPro Integer32 .1.3.6.1.4.1.1751.2.18.2.15.1.1 |
oc3APS OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.2.16 |
oc3APSPairConfigTableTable of common physical Port attributes SEQUENCE OF Oc3APSPairConfigEntry .1.3.6.1.4.1.1751.2.18.2.16.1 |
oc3APSPairConfigEntryRow definition for common physical
port attributes Oc3APSPairConfigEntry .1.3.6.1.4.1.1751.2.18.2.16.1.1 |
oc3APSPairIdAPS Pair Port index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.2.16.1.1.1 |
oc3APSPairModeUnidirectional or Bidirectional mode:
Uni - Each pair operates independently
i.e. a switch over in one pair does not
effect the remote pair.
Bi - both remote and local pairs have to
switch together.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.2 |
oc3APSPairOptionNonrevertive - After a switch to Prot port,
even if the working comes up there is no
switch to the working port back.
Revertive - traffic is switched back to
work port after it comes back.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.3 |
oc3APSPairWorkingSFBERThresholdBits error Rate threshold to declare signal failurerw Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.4 |
oc3APSPairWorkingSDBERThresholdBits error Rate threshold to declare signal degraderw Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.5 |
oc3APSPairProtectionSFBERThresholdBits error Rate threshold to declare signal failurerw Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.6 |
oc3APSPairProtectionSDBERThresholdBits error Rate threshold to declare signal degraderw Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.7 |
oc3APSPairWTRPeriodDuration for Wait To Restore Period between 5
to 12 minutes. Ref: BellCore GR-253-Core,
Issue 3, page 200, R5-56.rw INTEGER .1.3.6.1.4.1.1751.2.18.2.16.1.1.8 |
oc3APSWorkingSlotWorking slot of APS pair.ro Integer32 .1.3.6.1.4.1.1751.2.18.2.16.1.1.9 |
oc3APSProtectionSlotProtection slot of APS pair.ro Integer32 .1.3.6.1.4.1.1751.2.18.2.16.1.1.10 |
oc3APSActiveSlotActive slot of APS pair.ro Integer32 .1.3.6.1.4.1.1751.2.18.2.16.1.1.11 |
oc3APSPairStatusnoFailure : The protection line is not in use.
modeMismatch : one end is configured unidirectional
and the other is bidirectional (both
the ends should be configured in the same mode).
Also when one end is configured for 1:1 architechture
and the other end indicates it is configured for
1:n architechture.(Bidirectional mode only)
swByteFailure: protection switching byte failure - defect declared
when invalid / persistantly unacceptable codes are
received in the K1 byte. failure declared if defect
persists for an extended period.
Invalid code is when the incoming K1 byte contains
an unused code or a code irrelevant for the specific
switching operation.(Only in bi-directional mode)
chMismatch : channel mismatch is declared when the channel numbers
in the transmitted K1 byte and the received K2 byte
do not match for 50 ms.Channel mismatch is monitored
only in bidirectional mode.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.12 |
oc3APSPairUserCommandAPS Pair User Commandrw Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.13 |
oc3APSPairCurrentStateCurrent State of the APS state machinero Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.14 |
oc3APSPairWorkingLineSignalStatusSignal Status of the working port
(LOS / LOF / LCD / AIS etc.)ro Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.15 |
oc3APSPairProtectionLineSignalStatusSignal Status of the protection
port (LOS / LOF / LCD / AIS etc.)ro Enumeration .1.3.6.1.4.1.1751.2.18.2.16.1.1.16 |
sts1PortConfigTableTable of sts-1 specific port attributes SEQUENCE OF Sts1PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.17 |
sts1PortConfigEntryRow definition for sts-1 specific
port attributes Sts1PortConfigEntry .1.3.6.1.4.1.1751.2.18.2.17.1 |
sts1PortIdslot/port: SSPP IntfIndex .1.3.6.1.4.1.1751.2.18.2.17.1.1 |
sts1LineCodingThis variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
B3ZS refers to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.17.1.2 |
sts1LoopbackConfigThis variable represents the loopback
configuration of the sts-1 interface.
See above diagrams for explanations of loops.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.17.1.3 |
sts1TransmitClockSourceThe source of Tranmit Clock.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.
'localTiming' indicates that a local clock
source is used.
'cardFreeRun' indicates that a local oscillator on
the I/O card is used as the transmit clock.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.17.1.4 |
sts1LineBuildOutsts-1 line build outrw Enumeration .1.3.6.1.4.1.1751.2.18.2.17.1.5 |
sts1LineStatussts-1 line status:
1: dsx3NoAlarm: No alarm present
2: dsx3RcvRAIFailure: Receiving Yellow/Remote Alarm Indication
4: dsx3XmitRAIAlarm: Transmitting Yellow/Remote Alarm Indication 8: dsx3RcvAIS: Receiving AIS failure state
16: dsx3XmitAIS: Transmitting AIS failure statue
32: dsx3LOF: Receiving LOF failure state
64: dsx3LOS: Reveiving LOS failure state
128: dsx3LoopbackState: Looping the received signal
256: dsx3RcvTestCode: Receiving a Test Pattern
512: dsx3OtherFailure: any line status not defined
1024: dsx3RcvRmtAIS:
2048: dsx3RcvRmtOOF:
4096: dsx3RcvRmtLOS:
8192: dsx3RcvRmtIdle:
16384: dsx3RmtLoopback: Far end remote loopbackro INTEGER .1.3.6.1.4.1.1751.2.18.2.17.1.6 |
sts1StsPointersstatus of the sts-1 sts pointersrw Enumeration .1.3.6.1.4.1.1751.2.18.2.17.1.7 |
sts1VtPointersstatus of the sts-1 vt pointersrw Enumeration .1.3.6.1.4.1.1751.2.18.2.17.1.8 |
tasmPortConfigTableTable of common physical Port attributes SEQUENCE OF TasmPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.18 |
tasmPortConfigEntryRow definition for common physical
port attributes TasmPortConfigEntry .1.3.6.1.4.1.1751.2.18.2.18.1 |
tasmPortIdinterface index - SSPPro Integer32 .1.3.6.1.4.1.1751.2.18.2.18.1.1 |
protectionGroupConfigTableThis table gives the list of Slot
Protection Groups in the System. Slot protection
group in one in which there are n cards being
protected by 1 standby card. SEQUENCE OF ProtectionGroupConfigEntry .1.3.6.1.4.1.1751.2.18.2.19 |
protectionGroupConfigEntryRow Definition for the Protection Group
Tables ProtectionGroupConfigEntry .1.3.6.1.4.1.1751.2.18.2.19.1 |
protectionSlotIdProtection Group Index. Index is the
slot id of the Slot Configured as Protection. INTEGER .1.3.6.1.4.1.1751.2.18.2.19.1.1 |
workingSlotBitmapWorking Slot Bitmap which the protection
slot will monitorrw INTEGER .1.3.6.1.4.1.1751.2.18.2.19.1.2 |
protectionCommandList of commands which can be executed
on a protection Group.
Clear : This command is used to clear any previous
commands which may have been and get back
to normal nto1 operation
Forced SwitchOver To Protection : Switchover to
Protection card even if the working card
is in service active
These commands to used in conjunction with
the working slot id.rw Enumeration .1.3.6.1.4.1.1751.2.18.2.19.1.3 |
protectionCommandSlotIdThis is the working Slot to which command
has to be appliedrw INTEGER .1.3.6.1.4.1.1751.2.18.2.19.1.4 |
protectionGroupStatusProtection Status of a Protection Card.
Inservice and OutofService indicates if the card
has failed or still operational. Active or Standby
state indicates if it is carrying active traffic
or not.ro Enumeration .1.3.6.1.4.1.1751.2.18.2.19.1.5 |
workingSlotIdIf protection group status is active,
this field will give the slot which is being
working. In case it is in standby mode this
field will show 0ro INTEGER .1.3.6.1.4.1.1751.2.18.2.19.1.6 |
workingFailedBitmapGives Bitmap of the Failed Working Slots.
Subset of the Working Slot Bitmap.ro INTEGER .1.3.6.1.4.1.1751.2.18.2.19.1.7 |
protectionActiveCounterGive the Number of Times a Protection
has gone to active.ro Integer32 .1.3.6.1.4.1.1751.2.18.2.19.1.8 |
protectionOOSCounterGive the Number of Times a Protection
Card has failed.ro Integer32 .1.3.6.1.4.1.1751.2.18.2.19.1.9 |
channelConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.3 |
taxiChannelConfigTableTable of common physical Port attributes SEQUENCE OF TaxiChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.1 |
taxiChannelConfigEntryRow definition for common physical
port attributes TaxiChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.1.1 |
taxiChannelIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.1.1.1 |
taxiChannelIfTypeUNI or NNI typerw Enumeration .1.3.6.1.4.1.1751.2.18.3.1.1.2 |
taxiChannelSecuFeatureenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.1.1.3 |
ds3ChannelConfigTableTable of common physical channel attributes SEQUENCE OF Ds3ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.2 |
ds3ChannelConfigEntryRow definition for common physical
channel attributes Ds3ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.2.1 |
ds3ChannelIdinterface index - SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.2.1.1 |
ds3ChannelIfTypeUNI or NNI type,rw Enumeration .1.3.6.1.4.1.1751.2.18.3.2.1.2 |
ds3ChannelSecuFeatureInterface type configured on DS3 channelrw Enumeration .1.3.6.1.4.1.1751.2.18.3.2.1.3 |
ds1ChannelConfigTableTable of common physical Port attributes SEQUENCE OF Ds1ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.3 |
ds1ChannelConfigEntryRow definition for common physical
port attributes Ds1ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.3.1 |
ds1ChannelIdinterface index - SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.3.1.1 |
ds1ChannelIfTypeUNI or NNI type for ATM ,Frame Relay, or
ISDN service interface type for channelrw Enumeration .1.3.6.1.4.1.1751.2.18.3.3.1.2 |
ds1ChannelDs0Mapbit map of DS0 in channelrw OCTET STRING .1.3.6.1.4.1.1751.2.18.3.3.1.3 |
ds1ChannelCellMappingcell delineation mode for ATM cell bearing
servicesrw Enumeration .1.3.6.1.4.1.1751.2.18.3.3.1.4 |
ds1ChannelInputCodingRuleenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.3.1.5 |
ds1ChannelSecuFeatureenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.3.1.6 |
ds1ChannelSignalingrefers to robbed-bit signaling in
circuitEmulation interfaces.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.3.1.7 |
ds1ChannelCellScramblerefers to enabling/disabling cell scrambling on
ATM interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.3.1.8 |
msChannelConfigTableChannel configuration table for multi-serial
ports. SEQUENCE OF MsChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.4 |
msChannelConfigEntryRow definition for multi-serial channel config. MsChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.4.1 |
msChannelIdinterface index - SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.4.1.1 |
msChannelIfTypeinterface type for multi-serial portrw Enumeration .1.3.6.1.4.1.1751.2.18.3.4.1.2 |
msChannelCellBearingModeThe cell delineation mode is either LANET or
CCITT basedrw Enumeration .1.3.6.1.4.1.1751.2.18.3.4.1.3 |
msChannelCellBearingAddrModestandard - ATM Forum UNI 3.0/3.1
noiseTolerant - A proprietary noise tolerant
address mapping schemerw Enumeration .1.3.6.1.4.1.1751.2.18.3.4.1.4 |
msChannelCellBearingPayloadFecpayload error correction schemero Enumeration .1.3.6.1.4.1.1751.2.18.3.4.1.5 |
msChannelSecuFeatureenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.4.1.6 |
oc3ChannelConfigTableTable of common physical Port attributes SEQUENCE OF Oc3ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.5 |
oc3ChannelConfigEntryRow definition for common physical
port attributes Oc3ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.5.1 |
oc3ChannelIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.5.1.1 |
oc3ChannelIfTypeUNI or NNI typerw Enumeration .1.3.6.1.4.1.1751.2.18.3.5.1.2 |
oc3ChannelSecuFeatureenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.5.1.3 |
twoWireSourceChannelConfigTableTable of common physical Port attributes SEQUENCE OF TwoWireSourceChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.6 |
twoWireSourceChannelConfigEntryRow definition for common physical
port attributes TwoWireSourceChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.6.1 |
twoWireSourceChannelIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.6.1.1 |
twoWireSourceChannelIfTypeInterface types of 2W station(source) channel.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.2 |
twoWireSourceChannelConnectionTypeThis field selects ATM virtual circuit connection
type, PVC or SVC.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.3 |
twoWireSourceChannelCompandingLawThis field selects channel encoding/decoding
quantization interval, muLaw or aLaw.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.4 |
twoWireSourceChannelSecuFeatureenhancement featurero Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.5 |
twoWireSourceChannelVoiceCompressionvoice compression schemero Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.6 |
twoWireSourceChannelEchoCancellationThis field disables/enables twoWireSource card
echo cancellation function.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.7 |
twoWireSourceChannelSilenceSupressionThis field disables/enables twoWireSource card
silence suppression.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.8 |
twoWireSourceChannelEncapsulationAalThis field selects ATM cell payload format.
Aal1 - ATM Adaption Layer Type 1.
Yurie - A proprietary specific ATM cell payload
format for compressed data.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.9 |
twoWireSourceChannelSubscriberServiceThis field selects subscribed channel service
types.
plar - Private Line Automatic Ring
fxs - Foreign Exchange Subscriber End
s-signaling - A proprietary specific signaling
type based on AIN model.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.6.1.10 |
highSpeedChannelConfigTableTable of common physical Port attributes SEQUENCE OF HighSpeedChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.7 |
highSpeedChannelConfigEntryRow definition for common physical
port attributes HighSpeedChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.7.1 |
highSpeedChannelIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.7.1.1 |
highSpeedChannelIfTypeUNI or NNI typerw Enumeration .1.3.6.1.4.1.1751.2.18.3.7.1.2 |
dspChannelConfigTableTable of common physical Port attributes SEQUENCE OF DspChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.8 |
dspChannelConfigEntryRow definition for common physical
port attributes DspChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.8.1 |
dspChannelIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.8.1.1 |
dspChannelIfTypeChannel Interface Typerw Enumeration .1.3.6.1.4.1.1751.2.18.3.8.1.2 |
dspChannelInputCodingRuleInput Coding Rulero Enumeration .1.3.6.1.4.1.1751.2.18.3.8.1.3 |
dspChannelVoiceCompressionvoice compression schemerw Enumeration .1.3.6.1.4.1.1751.2.18.3.8.1.4 |
dspChannelEchoCancellationvoice compression schemero Enumeration .1.3.6.1.4.1.1751.2.18.3.8.1.5 |
dspChannelSilenceSupressionvoice compression schemero Enumeration .1.3.6.1.4.1.1751.2.18.3.8.1.6 |
twoWireSinkChannelConfigTableTable of common physical Port attributes SEQUENCE OF TwoWireSinkChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.9 |
twoWireSinkChannelConfigEntryRow definition for common physical
port attributes TwoWireSinkChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.9.1 |
twoWireSinkChannelIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.9.1.1 |
twoWireSinkChannelIfTypeInterface types.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.2 |
twoWireSinkChannelConnectionTypeThis field selects ATM virtual circuit connection
type, PVC or SVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.3 |
twoWireSinkChannelCompandingLawThis field selects channel encoding/decoding
quantization interval, muLaw or aLaw.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.4 |
twoWireSinkChannelVoiceCompressionvoice compression schemero Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.5 |
twoWireSinkChannelEchoCancellationThis field disables/enables twoWireSink card
echo cancellation function.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.6 |
twoWireSinkChannelSilenceSupressionThis field disables/enables twoWireSink card
silence suppression.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.7 |
twoWireSinkChannelEncapsulationAalThis field selects ATM cell payload format.
Aal1 - ATM Adaption Layer Type 1.
Yurie - A proprietary specific ATM cell payload
format for compressed data.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.8 |
twoWireSinkChannelSubscriberServiceThe only available service type for twoWireSink
card is Foreign Exchange Office End (fxo).ro Enumeration .1.3.6.1.4.1.1751.2.18.3.9.1.9 |
e3ChannelConfigTableTable of common physical channel attributes SEQUENCE OF E3ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.10 |
e3ChannelConfigEntryRow definition for common physical
channel attributes E3ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.10.1 |
e3ChannelIdinterface index - SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.10.1.1 |
e3ChannelIfTypeInterface type configured on E3 channelrw Enumeration .1.3.6.1.4.1.1751.2.18.3.10.1.2 |
e3ChannelSecuFeatureenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.10.1.3 |
e1ChannelConfigTableTable of common physical Port attributes SEQUENCE OF E1ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.11 |
e1ChannelConfigEntryRow definition for common physical
port attributes E1ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.11.1 |
e1ChannelIdinterface index - SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.11.1.1 |
e1ChannelIfTypeUNI or NNI type for ATM ,Frame Relay, or
ISDN serviceinterface type for channelrw Enumeration .1.3.6.1.4.1.1751.2.18.3.11.1.2 |
e1ChannelDs0Mapbit map of DS0 in channelrw OCTET STRING .1.3.6.1.4.1.1751.2.18.3.11.1.3 |
e1ChannelCellMappingcell delineation mode for ATM cell bearing
servicesrw Enumeration .1.3.6.1.4.1.1751.2.18.3.11.1.4 |
e1ChannelInputCodingRuleenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.11.1.5 |
e1ChannelSecuFeatureenhancement featurerw Enumeration .1.3.6.1.4.1.1751.2.18.3.11.1.6 |
e1ChannelSignalingRefers to robbed-bit singaling in
circuitEmulation interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.11.1.7 |
ethernetChannelConfigTableTable used for enthernet channel
configuration. SEQUENCE OF EthernetChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.12 |
ethernetChannelConfigEntryRow definition for enthernet channel
attributes. EthernetChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.12.1 |
ethernetChannelIdInterface index Integer32 .1.3.6.1.4.1.1751.2.18.3.12.1.1 |
ethernetChannelIfTypeTypes of ethernet interface.
There are two types of bridging
interface(channel):bridge and routing.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.12.1.2 |
dsp2Channel OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.3.13 |
dsp2ChannelConfigTableTable of Channel attributes SEQUENCE OF Dsp2ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.13.1 |
dsp2ChannelConfigEntryRow definition for common physical
port attributes Dsp2ChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.13.1.1 |
dsp2ChannelIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.13.1.1.1 |
dsp2ChannelIfTypeChannel Interface Typerw Enumeration .1.3.6.1.4.1.1751.2.18.3.13.1.1.2 |
dsp2ChannelAlarmTypeThis field is a read only failure which
gives the status of a dsp.When the status
is dspFailure the Operational Status at the
interface level will go OOSro Enumeration .1.3.6.1.4.1.1751.2.18.3.13.1.1.3 |
dsp2ChannelModeConfigThis field is used to configure the mode of
the DSP card. Each mode corresponds to a set
of algorithms supported by the IO card.
The complete list of enumerations of supported
algorithms is given in the dsp2AlgorithmTable.
The following description outlines the algorithms
supported in each corresponding AlgoSet.
algoSet1 : g168-echo-cancellation128ms
algoSet2 : g726-voice-compression,
g165-echo-cancellation,
generic-silence-suppression,
fax-modem-tone-detection,
g168-echo-cancellation64ms.
algoSet3 : g729a-voice-compression,
g165-echo-cancellation,
g729b-silence-suppression,
fax-modem-tone-detection,
g168-echo-cancellation64ms.
algoSet4 : v17-fax-algorithm-upto-14400-bps,
v29-fax-algorithm-upto-9600-bps,
v27ter-fax-algorithm-upto-2400-bps,
v21-fax-algorithm-upto-300-bps.
algoSet5 : g168-echo-cancellation64ms.
algoSet6 : g726-voice-compression,
g729a-voice-compression,
g729b-silence-suppression,
g168-echo-cancellation64ms,
v17-fax-algorithm-upto-14400-bps,
v29-fax-algorithm-upto-9600-bps,
v27ter-fax-algorithm-upto-2400-bps,
v21-fax-algorithm-upto-300-bps.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.13.1.1.4 |
dsp2AlgorithmTableTable of dsp2 algorithms assigned to interface. SEQUENCE OF Dsp2AlgorithmEntry .1.3.6.1.4.1.1751.2.18.3.13.2 |
dsp2AlgorithmEntryRow definition for dsp2 algorithms assigned to
interfaces. Dsp2AlgorithmEntry .1.3.6.1.4.1.1751.2.18.3.13.2.1 |
dsp2AlgorithmIdinterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.13.2.1.1 |
dsp2AlgorithmTypeDSP Algorithm type.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.13.2.1.2 |
imaGrpChannelConfigTableTable used for the IMA virtual channel (group)
configuration on cards that have physical
interfaces configured as atmIma. Represents three
channels that can be configured as IMA groups on
port 7 of DS1 and E1 cards. SEQUENCE OF ImaGrpChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.14 |
imaGrpChannelConfigEntryRow definition for common physical
port attributes ImaGrpChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.14.1 |
imaGrpChannelIdinterface index - SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.14.1.1 |
imaGrpChannelIfTypeinterface typerw Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.2 |
imaGrpChannelPortMapA bitmap that identifies the physical IMA
interfaces in this group. The least significant
bit represents port 1.rw Integer32 .1.3.6.1.4.1.1751.2.18.3.14.1.3 |
imaGrpChannelNeStateThe current operational state of the near-end IMA
Group State Machine.ro ImaGrpChannelEndState .1.3.6.1.4.1.1751.2.18.3.14.1.4 |
imaGrpChannelFeStateThe current operational state of the far-end IMA
Group State Machine.ro ImaGrpChannelEndState .1.3.6.1.4.1.1751.2.18.3.14.1.5 |
imaGrpChannelFailureStatusThe current failure status of the IMA group
(the reason why the GTSM is in the down state).
noFailure(1) no failure
startUpNe(2) near-end is in the state of start-up
startUpFe(3) far-end is in the state of start-up
invalidMValueNe(4) near-end has invalid frame length
invalidMValueFe(5) far-end has invalid frame length
failedAssymetricNe(6) near-end failed due to incompatable
symmetry
failedAssymetricFe(7) far-end failed due to incompatable
symmetry
insuffLinksNe(8) Near-end reported less than the min
number of Tx links are active or
less than the min number
of Rx links are active
insuffLinksFe(9) Far-end reported less than the min
number of Rx links are active or less
than thenmin number of Tx links are
active
blockedNe(10) Near-end is administratively
out-of-service
blockedFe(11) Far-end is administratively
out-of-service
otherFailure(12) other failuresro Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.6 |
imaGrpChannelSymmetrySymmetry of the IMA group.
Symmetric configuration: all ports of IMA group are
configured as full-duplex. With symmetric configuration,
operation is symmetric if no links failes; is asymmetric
if a link fails so that the active forward and backward
links between far-end and near-end are asymmetric. If
the configuration is asymmetric, the operation can never
be symmetric.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.7 |
imaGrpChannelMinNumTxLinksMinimum number of transmit links required to be
Active for the IMA group to be in the Up state.rw INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.8 |
imaGrpChannelMinNumRxLinksMinimum number of receive links required to be
Active for the IMA group to be in the Up state.rw INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.9 |
imaGrpChannelNeTxClkModeTransmit clocking mode used by the near-end IMA
group. There are two possible modes: the Common Transmit
Clock (CTC) and the Independent Transmit Clock (ITC). The
CTC mode corresponds to the case when the transmit clock of
all IMA links are derived from the same source. The ITC
configuration corresponds to the case where there is at
least one IMA link whose transmit clock is derived from a
source different than at least another link transmit clock.
The underlying clock configuration must be set up by the
user to ensure operation in the selected mode.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.10 |
imaGrpChannelFeTxClkModeTransmit clocking mode used by the far-end IMA group.
There are two possible modes: the Common Transmit
Clock (CTC) and the Independent Transmit Clock (ITC).
The CTC mode corresponds to the case when the transmit clock
of all IMA links are derived from the same source. The ITC
configuration corresponds to the case where there is at least
one IMA link whose transmit clock is derived from a source
different than at least another link transmit clock.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.11 |
imaGrpChannelTxImaIdThe IMA ID currently in use by the near-end IMA
function.rw INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.12 |
imaGrpChannelRxImaIdThe IMA ID currently in use by the far-end IMA
function.ro INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.13 |
imaGrpChannelTxFrameLengthThe frame length to be used by the IMA group in the transmit
direction. Can only be set when the IMA group is startup.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.14 |
imaGrpChannelRxFrameLengthValue of IMA frame length as received from
remote IMA function.ro Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.15 |
imaGrpChannelDiffLinkDelayMaxThe maximum number of milliseconds of delay differential among
the links that will be tolerated on this interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.16 |
imaGrpChannelLeastDelayLinkThe Interface Index of the link configured in the IMA
group which has the smallest link propagation delay. This
value has meaning only if at least 1 link has been configured
in the IMA group.ro IntfIndex .1.3.6.1.4.1.1751.2.18.3.14.1.17 |
imaGrpChannelDiffDelayMaxObsThe latest maximum differential delay observed (in
milliseconds), i.e. between the links having the least and
most link propagation delay, among the receive links that
are currently configured in the IMA group.ro Integer32 .1.3.6.1.4.1.1751.2.18.3.14.1.18 |
imaGrpChannelAlphaValueThis indicates the 'alpha' value used to specify the
number of consecutive invalid ICP cells to be detected
before moving to the IMA HUNT state.rw INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.19 |
imaGrpChannelBetaValueThis indicates the 'beta' value used to specify the
number of consecutive errored ICP cells to be detected
before moving to the IMA HUNT state.rw INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.20 |
imaGrpChannelGammaValueThis indicates the 'gamma' value used to specify the
number of consecutive valid ICP cells to be detected before
moving to the IMA SYNC state from the PRESYNC state.rw INTEGER .1.3.6.1.4.1.1751.2.18.3.14.1.21 |
imaGrpChannelStatsNeNumFailuresThe number of times a near-end group failure (Config-Abort,
Insufficient-Links) has been reported.ro Integer32 .1.3.6.1.4.1.1751.2.18.3.14.1.22 |
imaGrpChannelStatsFeNumFailuresThe number of times a far-end group failure (Config-Abort-FE,
Insufficient-Links-FE, Blocked-FE) has been reported.ro Integer32 .1.3.6.1.4.1.1751.2.18.3.14.1.23 |
imaGrpChannelStatsNumTxActLnksThe number of links which are configured to transmit and are
currently Active in this IMA group.ro Integer32 .1.3.6.1.4.1.1751.2.18.3.14.1.24 |
imaGrpChannelStatsNumRxActLnksThe number of links which are configured to receive and are
currently Active in this IMA group.ro Integer32 .1.3.6.1.4.1.1751.2.18.3.14.1.25 |
imaGrpChannelStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.3.14.1.26 |
imaGrpChannelCompatModeThis is used to indicate interoperability mode to the I/O
card in terms of reporting the link status at the correct
location in the IMA Control Protocol (ICP) cellrw Enumeration .1.3.6.1.4.1.1751.2.18.3.14.1.27 |
tasmChannelConfigTableTable of common physical Channel attributes SEQUENCE OF TasmChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.15 |
tasmChannelConfigEntryRow definition for common physical
channel attributes TasmChannelConfigEntry .1.3.6.1.4.1.1751.2.18.3.15.1 |
tasmChannelIdInterface index - SSPPCC IntfIndex .1.3.6.1.4.1.1751.2.18.3.15.1.1 |
tasmChannelIfTypeChannel Interface Typerw Enumeration .1.3.6.1.4.1.1751.2.18.3.15.1.2 |
tasmChannelAlarmTypeThis field is a read only failure which
gives the status of a DSP in the TASM card.When
the status is tasmFailure the Operational Status
at the interface level will go OOSro Enumeration .1.3.6.1.4.1.1751.2.18.3.15.1.3 |
tasmChannelModeConfigThis field is used to configure the mdoe in which
a TASM DSP will be used asd a resource. The modes are
explained as follows:
casMode: DSP resource is used for DTMF/MF
tone detection/generation and running the
Type 100, 105, and 108 tests.
tasMode: DSP resource is used for playing/compressing
announcement.rw Enumeration .1.3.6.1.4.1.1751.2.18.3.15.1.4 |
intfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.5 |
atmUniConfigTableTable of atm user to network interface (UNI) SEQUENCE OF AtmUniConfigEntry .1.3.6.1.4.1.1751.2.18.5.1 |
atmUniConfigEntryRow definition of atm UNI AtmUniConfigEntry .1.3.6.1.4.1.1751.2.18.5.1.1 |
atmUniIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.1.1.1 |
atmUniAddrTypeatm address typerw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.2 |
atmUniSvcMinVpiThe lower bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.3 |
atmUniSvcMaxVpiThe upper bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.4 |
atmUniSvcMinVciThe lower bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.5 |
atmUniSvcMaxVciThe upper bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.6 |
atmUniAdminStatusThe administrative action:
'outOfService' means take the UNI out of service
'inService' means take the UNI in service
'delete' remove/deconfigure the UNI.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.7 |
atmUniOperStatusThe operational status of the UNI:
'outOfService' means the UNI is out of service
'inService' means the UNI is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.8 |
atmUniNwPrefix1ATM Network Prefix 1rw OCTET STRING .1.3.6.1.4.1.1751.2.18.5.1.1.9 |
atmUniOverSubscriptionOver subscription factorrw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.10 |
atmUniT303Timer T303 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.11 |
atmUniT308Timer T308 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.12 |
atmUniT309Timer T309 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.13 |
atmUniT310Timer T310 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.14 |
atmUniT313Timer T313 value - User side only - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.15 |
atmUniT316Timer T316 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.16 |
atmUniT317Timer T317 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.17 |
atmUniT322Timer T322 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.18 |
atmUniT398Timer T398 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.19 |
atmUniT399Timer T399 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.20 |
atmUniMyNeighborIpAddressThe IP address of the neighbor system connected to
the far end of this interface, to which a Network
Management Station can send SNMP messages, as IP
datagrams sent to UDP port 161, in order to access
network management information concerning the
operation of that system. Note that the value
of this object can currently only be obtained
by manual configuration.rw IpAddress .1.3.6.1.4.1.1751.2.18.5.1.1.21 |
atmUniMyNeighborIfNameThe textual name of the interface on the neighbor
system on the far end of this interface, and to
which this interface connects. If the neighbor
system is manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface for this
port. If this interface does not have a
textual name, the value of this object is a zero
length string. Note that the value of this object
can currently only be obtained by manual
configuration.rw DisplayString .1.3.6.1.4.1.1751.2.18.5.1.1.22 |
atmUniVpiSigVPI value for the signalling channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.23 |
atmUniVciSigVCI value for the signalling channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.24 |
atmUniVpiIlmiVPI value for the ilmi channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.25 |
atmUniVciIlmiVCI value for the ilmi channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.26 |
atmUniAtmSignalingStatusIndicates if atm signaling is enabled or disabled
for this interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.27 |
atmUniMyIfNameA textual name of this interface. If this system
is manageable manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface for this
port. This interface must be uniquely named on
this system to distinguish parallel links with a
neighboring system. If this interface does not
have a textual name, the value of this object is a
zero length string.rw DisplayString .1.3.6.1.4.1.1751.2.18.5.1.1.29 |
atmUniIlmiProtocolStatusThe administrative status:
'enabled' - ILMI protocol enabled on UNI
'disabled' - ILMI protocol disabled on UNI.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.30 |
atmUniIlmiOperStatusThe operational status:
'outOfService' - ILMI connectivity is down
'inService' - ILMI connectivity is up.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.31 |
atmUniIlmiConfigProcILMI Configuration Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.32 |
atmUniIlmiConnectProcILMI Connectivity Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.33 |
atmUniIlmiAttachPtProcILMI Attachment Point Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.34 |
atmUniIlmiSecureLinkProcILMI Secure Link Procedure status. Can be enabled
only if Attachment Point Procedure is enabled.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.35 |
atmUniIlmiAddrRegProcILMI Address Registration Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.36 |
atmUniIlmiTimerSTimer S (secs). Used to poll peer when link is
down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.37 |
atmUniIlmiTimerTTimer T (secs). Used to poll peer when link is
up.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.38 |
atmUniIlmiRetryKRetry K - number of timeouts before link is
declared down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.39 |
atmUniIntfTypeatm interface typerw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.40 |
atmUniUserAddressATM User Addressrw OCTET STRING .1.3.6.1.4.1.1751.2.18.5.1.1.41 |
atmUniViSuppFlagvirtual interface supp off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.42 |
atmUniUPCSuppupc supp off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.43 |
atmUniUbrLoadBalSuppload balancing supp for ubr conns off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.44 |
atmUniAvailBwIgrThe Avail Bandwidth for that interface in
cells per sec. Bandwidth for UBR conns
will not be accounted forro Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.45 |
atmUniAvailBwEgrThe Avail Bandwidth for that interface in
cells per sec which can go out of the
interface. Bandwidth for UBR conns
will not be accounted forro Integer32 .1.3.6.1.4.1.1751.2.18.5.1.1.46 |
atmUniVUNISuppFlagvirtual UNI interface supp off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.47 |
atmUniUserAddrOrgScopeATM User Address Organizational scoperw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.48 |
atmUniSscopRxWndSzThe receive window size for the SSCOP layerrw INTEGER .1.3.6.1.4.1.1751.2.18.5.1.1.49 |
atmUniConnTrafficShapingFlagTraffic Shaping for Conn was enabled
primarily because the core would lose
cells since we were non-conformant cells.
Therefore the hardware added traffic
shaping per connection. But condition is
VI should not be enabled if this feature
is enabled.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.1.1.50 |
atmIispConfigTableTable of atm iisp interface SEQUENCE OF AtmIispConfigEntry .1.3.6.1.4.1.1751.2.18.5.2 |
atmIispConfigEntryRow definition of atm iisp interface AtmIispConfigEntry .1.3.6.1.4.1.1751.2.18.5.2.1 |
atmIispIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.2.1.1 |
atmIispSvcMinVpiThe lower bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.2.1.2 |
atmIispSvcMaxVpiThe upper bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.2.1.3 |
atmIispSvcMinVciThe lower bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.2.1.4 |
atmIispSvcMaxVciThe upper bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.2.1.5 |
atmIispAdminStatusThe administrative action:
'outOfService' means take the UNI out of service
'inService' means take the UNI in service
'delete' remove/deconfigure the UNI.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.2.1.6 |
atmIispOperStatusThe operational status of the UNI:
'outOfService' means the UNI is out of service
'inService' means the UNI is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.2.1.7 |
atmIispOverSubscriptionOver subscription factorrw INTEGER .1.3.6.1.4.1.1751.2.18.5.2.1.8 |
atmIispT303Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.9 |
atmIispT308Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.10 |
atmIispT309Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.11 |
atmIispT310Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.12 |
atmIispT316Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.13 |
atmIispT317Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.14 |
atmIispT322Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.15 |
atmIispT398Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.16 |
atmIispT399Timer value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.17 |
atmIispAtmSignalingStatusIndicates if atm signaling is enabled or disabled
for this interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.2.1.18 |
atmIispAvailBwIgrThe Avail Bandwidth for that interface in
cells per sec. Bandwidth for UBR conns
will not be accounted for.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.19 |
atmIispAvailBwEgrThe Avail Bandwidth for that interface in
cells per sec. Bandwidth for UBR conns
will not be accounted for.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.2.1.20 |
atmIispUPCSuppupc supp off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.2.1.21 |
atmIispUbrLoadBalSuppload balancing supp for ubr conns off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.2.1.22 |
atmIispSscopRxWndSzThe receive window size for the SSCOP layerrw INTEGER .1.3.6.1.4.1.1751.2.18.5.2.1.23 |
atmIispConnTrafficShapingFlagTraffic Shaping for Conn was enabled
primarily because the core would lose
cells since we were non-conformant cells.
Therefore the hardware added traffic
shaping per connection. But condition is
VI should not be enabled if this feature
is enabled.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.2.1.24 |
atmCirEmConfigTableTable for ATM Circuit Emulation Interface SEQUENCE OF AtmCirEmConfigEntry .1.3.6.1.4.1.1751.2.18.5.3 |
atmCirEmConfigEntryRow definition for ATM Circuit Emulation
interface AtmCirEmConfigEntry .1.3.6.1.4.1.1751.2.18.5.3.1 |
atmCirEmIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.3.1.1 |
atmCirEmAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.3.1.2 |
atmCirEmOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.3.1.3 |
atmCirEmCASIdleAbcdPatternabcd bit pattern for cirEm AISrw INTEGER .1.3.6.1.4.1.1751.2.18.5.3.1.4 |
atmCirEmCASBusyAbcdPatternabcd bit pattern for cirEm RDIrw INTEGER .1.3.6.1.4.1.1751.2.18.5.3.1.5 |
atmCirEmAlarmDataPatterndata pattern for cirEm AISrw INTEGER .1.3.6.1.4.1.1751.2.18.5.3.1.6 |
atmCirEmTCPatternShould abcd bits be toggled after 2.5 Secs.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.3.1.7 |
atmCirEmDownStInterworkingThis field will be used to select
the type of interworking to be
done in the down stream direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.3.1.8 |
atmTermEmConfigTableTable for ATM Terminal Emulation Interface SEQUENCE OF AtmTermEmConfigEntry .1.3.6.1.4.1.1751.2.18.5.4 |
atmTermEmConfigEntryRow definition for ATM Terminal Emulation
interface AtmTermEmConfigEntry .1.3.6.1.4.1.1751.2.18.5.4.1 |
atmTermEmIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.4.1.1 |
atmTermEmRxTimeOutreceive timeout value in tenths of seconds.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.4.1.2 |
atmTermEmAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.4.1.3 |
atmTermEmOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.4.1.4 |
hdlcConfigTableTable for an HDLC Pass Through Interface SEQUENCE OF HdlcConfigEntry .1.3.6.1.4.1.1751.2.18.5.5 |
hdlcConfigEntryRow definition for an HDLC Pass Through interface HdlcConfigEntry .1.3.6.1.4.1.1751.2.18.5.5.1 |
hdlcIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.5.1.1 |
hdlcAdminStatusThe administrative action:
'outOfService' means take the interface out of service
'inService' means take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.5.1.2 |
hdlcOperStatusThe operational status of the interface:
'outOfService' means the interface is out of service
'inService' means the interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.5.1.3 |
hdlcThroughPutThe throughput bandwidth of the interface:
'k64' means a throughput of 64 kb
'k56' means a throughput of 56 kbrw Enumeration .1.3.6.1.4.1.1751.2.18.5.5.1.4 |
hdlcDataInversionFlag indicating whether data inversion is
performed by the IO card for this interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.5.1.5 |
frUniConfigTableTable for Frame Realy UNI Interface SEQUENCE OF FrUniConfigEntry .1.3.6.1.4.1.1751.2.18.5.6 |
frUniConfigEntryRow definition for Frame Relay interface FrUniConfigEntry .1.3.6.1.4.1.1751.2.18.5.6.1 |
frUniIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.6.1.1 |
frUniAddrDlciLenLength of Data Link connection identify of
frame relay UNI addressro Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.2 |
frUniDlcmiStateThe state of Data Link Connection Management
Indentify of frame relay UNI.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.3 |
frUniAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.4 |
frUniOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.5 |
frUniOverSubscriptionAllow for the 'reserved' bandwidth allocated
to oversubscribe the line by up to a factor
of 10 . Generally, a figure of between 1 and 4
is normally a safe bet, although higher levels
are often acceptable.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.6.1.6 |
frUniLmiProtocolLmi protocol to runrw Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.7 |
frUniInterworkingTypefrf5 - fr/atm network interworking
frf8 - fr/atm service interworkingrw Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.8 |
frUniN391full status polling counter.
DTE:Mandatory, DCE:N/Arw INTEGER .1.3.6.1.4.1.1751.2.18.5.6.1.9 |
frUniN392error threshold. DTE:Mandatory, DCE:Mandatoryrw INTEGER .1.3.6.1.4.1.1751.2.18.5.6.1.10 |
frUniN393Monitored event count. DTE:Mandatory,
DCE:N/Arw INTEGER .1.3.6.1.4.1.1751.2.18.5.6.1.11 |
frUniT391Link integrity verification timer.
DTE:Mandatory, DCE:N/Arw INTEGER .1.3.6.1.4.1.1751.2.18.5.6.1.12 |
frUniT392Polling verification timer.
DTE:N/A, DCE:Mandatoryrw INTEGER .1.3.6.1.4.1.1751.2.18.5.6.1.13 |
frUniAsyncLmiAsync PVC status messagesrw Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.14 |
frLmiOperStatusThe operational status of the lmi protocol:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.15 |
frUniNT3Message frequency timer relevant for ATT LMI only.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.6.1.16 |
frUniThroughPutThe throughput bandwidth of the interface:
'k64' means a throughput of 64 kb
'k56' means a throughput of 56 kbrw Enumeration .1.3.6.1.4.1.1751.2.18.5.6.1.17 |
dspConfigTableTable for Dsp Interface SEQUENCE OF DspConfigEntry .1.3.6.1.4.1.1751.2.18.5.7 |
dspConfigEntryRow definition for Dsp interface DspConfigEntry .1.3.6.1.4.1.1751.2.18.5.7.1 |
dspIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.7.1.1 |
dspAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.7.1.2 |
dspOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.7.1.3 |
bridgeConfigTableTable which hold Config Entries
for all bridges. SEQUENCE OF BridgeConfigEntry .1.3.6.1.4.1.1751.2.18.5.8 |
bridgeConfigEntryRow definition for bridge entries BridgeConfigEntry .1.3.6.1.4.1.1751.2.18.5.8.1 |
bridgeIfIndexinterface index (slot/port/channel) SSPPCCC Integer32 .1.3.6.1.4.1.1751.2.18.5.8.1.1 |
bridgeAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.8.1.2 |
bridgeOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.8.1.3 |
bridgeNumberThe number of bridgesrw INTEGER .1.3.6.1.4.1.1751.2.18.5.8.1.4 |
bridgePortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
dot1dStpPort.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.8.1.5 |
bridgePathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port. 802-1D-1990 recommends that the
default value of this parameter be in inverse
proportion to the speed of the attached LAN.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.8.1.6 |
bridgeConnectionTypeConnection typesrw Enumeration .1.3.6.1.4.1.1751.2.18.5.8.1.7 |
bridgeDomainTableA table which holds the bridgeDomainEntry data SEQUENCE OF BridgeDomainEntry .1.3.6.1.4.1.1751.2.18.5.9 |
bridgeDomainEntryA table entry for a Bridge Domain on
an ethernet card BridgeDomainEntry .1.3.6.1.4.1.1751.2.18.5.9.1 |
bridgeDomainNumberThe bridge number of the bridge which this
interface is a part of. If the interface is
currently not associated with any bridge this
will be set to none. Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.1 |
bridgeDomainAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in servicerw Enumeration .1.3.6.1.4.1.1751.2.18.5.9.1.2 |
bridgeDomainOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.9.1.3 |
bridgeDomainPriorityThe value of the writeable portion of the Bridge
ID, i.e., the first two octets of the (8 octet
long) Bridge ID. The other (last) 6 octets of the
Bridge ID are given by the value of
dot1dBaseBridgeAddress.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.9.1.4 |
bridgeDomainTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detedted by the
bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.1751.2.18.5.9.1.5 |
bridgeDomainDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.5.9.1.6 |
bridgeDomainRootCostThe cost of the path to the root as seen from
this bridge.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.7 |
bridgeDomainRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.8 |
bridgeDomainMaxMessageAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.9 |
bridgeDomainHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.10 |
bridgeDomainHoldTimeThis time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.11 |
bridgeDomainForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
state. The value determines how long the port
stays in each of the Listening and Learning states,
which precede the Forwarding state. This value is
also used, when a topology change has been detected
and is underway, to age all dynamic entries in the
Forwarding Database. [Note that this value is the
one that this bridge is currently using, in
contrast to bridgeDomainBridgeForwardDelay which is
the value that this bridge and all others would
start using if/when this bridge were to become
the root.]ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.12 |
bridgeDomainMaxBridgeAgeThe value that all bridges use for MaxAge when
this bridge is acting as the root. Note that
802.1D-1990 specifies that the range for this
parameter is related to the value of
bridgeDomainBridgeHelloTime. The granularity of
this timer is specified by 802.1D-1990 to be 1
second. An agent may return a badValue error if a
set is attempted to a value which is not a whole
number of seconds.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.9.1.13 |
bridgeDomainBridgeHelloTimeThe value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by 802.1D-
1990 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.9.1.14 |
bridgeDomainBridgeForwardDelayThe value that all bridges user for ForwardDelay
when this bridge is acting as the root. Note that
802.1D-1990 specifies that the range for this
parameter is related to the value of
bridgeDomainMaxBridgeAge. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.9.1.15 |
bridgeDomainAgingTimeThe timeout period in seconds for aging out
dynamically learned forwarding information.
802.1D-1990 recommends a default of 300 seconds.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.9.1.16 |
bridgeDomainSpanningTreeAllows the bridge to be configured to run
without the spanning tree algorithm.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.9.1.17 |
bridgeDomainTopologyChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.18 |
bridgeDomainLearnedEntryDiscardsThe total number of Forwarding Database entries,
which have been or would have been learnt, but
have been discarded due to a lack of space to
store them in the Forwarding Database. If this
counter is increasing, it indicates that the
Forwarding Database is regularly becoming full (a
condition which has unpleasant performance effects
on the subnetwork). If this counter has a
significant value but is not presently increasing,
it indicates that the problem has been occurring
but is not persistent.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.19 |
bridgeDomainTimerNumber of seconds elapsed since
the last reset of bridge group statisticsro Integer32 .1.3.6.1.4.1.1751.2.18.5.9.1.20 |
bridgeDomainDefaultGatewayThe default gateway for this bridge domain.
This is now an obsolete entryrw IpAddress .1.3.6.1.4.1.1751.2.18.5.9.1.21 |
bridgeDomainPortStatusBitmapA bit map describing which ports
in a bridge group are up or downro OCTET STRING .1.3.6.1.4.1.1751.2.18.5.9.1.22 |
routerConfigTableTable which hold Config Entries
for all routers (VPNs) SEQUENCE OF RouterConfigEntry .1.3.6.1.4.1.1751.2.18.5.10 |
routerConfigEntryconfig data for a router (VPN) RouterConfigEntry .1.3.6.1.4.1.1751.2.18.5.10.1 |
routerIfIndexA scalar number which identifies an IP
interface within a given router (VPN) Integer32 .1.3.6.1.4.1.1751.2.18.5.10.1.1 |
routerAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.10.1.2 |
routerOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.10.1.3 |
routerIpAddressrouter ATM IP Address.rw IpAddress .1.3.6.1.4.1.1751.2.18.5.10.1.4 |
routerIpNetworkMaskAn IP network mask for an IP interface
within a given router (VPN)rw IpAddress .1.3.6.1.4.1.1751.2.18.5.10.1.5 |
routerNumberA scalar number which identifies
a given router (VPN)rw INTEGER .1.3.6.1.4.1.1751.2.18.5.10.1.6 |
routerEthernetIpAddressrouter Ethernet IP Address.rw IpAddress .1.3.6.1.4.1.1751.2.18.5.10.1.7 |
isdnConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.5.11 |
isdnIntfConfigTableTable of ISDN interface configuration attriburtes SEQUENCE OF IsdnIntfConfigEntry .1.3.6.1.4.1.1751.2.18.5.11.1 |
isdnIntfConfigEntryRow definition for ISDN interface configuration
table IsdnIntfConfigEntry .1.3.6.1.4.1.1751.2.18.5.11.1.1 |
isdnIntfIdInterface ID (SSPPCCC) Integer32 .1.3.6.1.4.1.1751.2.18.5.11.1.1.1 |
isdnIntfDChanIdD-Channel Number - if the Dchannel no.
is 0 no LAPD will run on this PRI-ISDN interfacerw Integer32 .1.3.6.1.4.1.1751.2.18.5.11.1.1.2 |
isdnIntfAdminStatusISDN interface admin statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.11.1.1.3 |
isdnIntfOperStatusISDN interface operational statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.11.1.1.4 |
isdnIntfSwitchTypeISDN interface Switch Typerw Enumeration .1.3.6.1.4.1.1751.2.18.5.11.1.1.5 |
isdnL2ConfigTableTable of Layer 2 (LAPD) attributes SEQUENCE OF IsdnL2ConfigEntry .1.3.6.1.4.1.1751.2.18.5.11.2 |
isdnL2ConfigEntryRow definition for ISDN LAPD parameters IsdnL2ConfigEntry .1.3.6.1.4.1.1751.2.18.5.11.2.1 |
isdnL2IntfIdInterface index (SSPPCCC) Integer32 .1.3.6.1.4.1.1751.2.18.5.11.2.1.1 |
isdnT200value of L2 T200 timer in 1/10 secondsrw INTEGER .1.3.6.1.4.1.1751.2.18.5.11.2.1.2 |
isdnT203value of L2 T203 timer in secondsrw INTEGER .1.3.6.1.4.1.1751.2.18.5.11.2.1.3 |
isdnN200Maximum number of retransmissions before
the LAPD Link is declared as downrw INTEGER .1.3.6.1.4.1.1751.2.18.5.11.2.1.4 |
isdnN201Maximum number of octets in an information
field - Maximum value of this parameter
will be 300 bytes.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.11.2.1.5 |
isdnKMaximum number of outstanding I frames -
L2 - window size.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.11.2.1.6 |
isdnL2OperStatusISDN Layer 2 operational status -
not-initiated means that first SETUP message
has not been transmitted and L2 estalishment
procedure has not been initiated yetro Enumeration .1.3.6.1.4.1.1751.2.18.5.11.2.1.7 |
isdnL2CurrentStateISDN Layer 2 protocol's current statero Enumeration .1.3.6.1.4.1.1751.2.18.5.11.2.1.8 |
isdnBChanConfigTableTable of ISDN B Channel configuration attriburtes SEQUENCE OF IsdnBChanConfigEntry .1.3.6.1.4.1.1751.2.18.5.11.3 |
isdnBChanConfigEntryRow definition for ISDN B Channel configuration
table IsdnBChanConfigEntry .1.3.6.1.4.1.1751.2.18.5.11.3.1 |
isdnBChanIdB Chan ID (SSPPCCC) Integer32 .1.3.6.1.4.1.1751.2.18.5.11.3.1.1 |
isdnBChanAdminStatusISDN B Chan admin statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.11.3.1.2 |
isdnBChanOperStatusISDN B Chan operational statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.11.3.1.3 |
atmDbCirEmConfigTableTable for ATM DBCES Interface SEQUENCE OF AtmDbCirEmConfigEntry .1.3.6.1.4.1.1751.2.18.5.12 |
atmDbCirEmConfigEntryRow definition for ATM Dynamic Bandwidth Circuit
Emulation interface. AtmDbCirEmConfigEntry .1.3.6.1.4.1.1751.2.18.5.12.1 |
atmDbCirEmIfIndexInterface index (slot/port/channel) SSPPCCC. IntfIndex .1.3.6.1.4.1.1751.2.18.5.12.1.1 |
atmDbCirEmAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.12.1.2 |
atmDbCirEmOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.12.1.3 |
atmDbCirEmIdlePatternIdle pattern for idle data.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.12.1.7 |
atmDbCirEmServiceTypeService type to be used. Affects the ABCD
Signaling.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.12.1.8 |
atmDbCirEmDbcesTypeThe type of dbces used.
yurie: Yurie proprietary specific.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.12.1.9 |
atmDbCirEmIntegrationTimeThis specifies the time to wait after receiving
idle pattern to change state. The unit is in
seconds.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.12.1.10 |
lmiDlciConfigTableTable for Lmi DLCI Interface. SEQUENCE OF LmiDlciConfigEntry .1.3.6.1.4.1.1751.2.18.5.13 |
lmiDlciConfigEntryRow definition for Lmi DLCI Interface. LmiDlciConfigEntry .1.3.6.1.4.1.1751.2.18.5.13.1 |
lmiDlciIfIndexInterface index (slot/port/channel) SSPPCCC. IntfIndex .1.3.6.1.4.1.1751.2.18.5.13.1.1 |
lmiDlcidlci. Integer32 .1.3.6.1.4.1.1751.2.18.5.13.1.2 |
lmiDlciOperStatusThe operational status of the lmi protocol:
'outOfService' protocol is out of service
'inService' protocol is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.13.1.3 |
lmiDlciStatusTimeTime since last status transition occurred.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.13.1.4 |
dsp2ConfigTableTable for Dsp2 Interface SEQUENCE OF Dsp2ConfigEntry .1.3.6.1.4.1.1751.2.18.5.14 |
dsp2ConfigEntryRow definition for Dsp2 interface Dsp2ConfigEntry .1.3.6.1.4.1.1751.2.18.5.14.1 |
dsp2IfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.14.1.1 |
dsp2AdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.14.1.2 |
dsp2OperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.14.1.3 |
dsp2LoadCountGives the number of calls going through that dsp.
This will be of use in case of deletion of
dsp interface. When no calls are going through
the dsp this value will be 0ro Integer32 .1.3.6.1.4.1.1751.2.18.5.14.1.4 |
dsp2AalModeaal2-non-multiplexed : Does not support
multiplexing of multiple channels with one trunk
aal2-standard: Support Standard Aal2 Multiplexing
aal1:Support Aal1 mode.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.14.1.5 |
atmImaConfigTableInverse Multiplexing interface table. SEQUENCE OF AtmImaConfigEntry .1.3.6.1.4.1.1751.2.18.5.15 |
atmImaConfigEntryRow definition for Inverse Multiplexing
attributes AtmImaConfigEntry .1.3.6.1.4.1.1751.2.18.5.15.1 |
atmImaIntfIndexinterface index (slot/port/channel) SSPPCCC Integer32 .1.3.6.1.4.1.1751.2.18.5.15.1.1 |
atmImaNeTxStateThe near-end transmit state.
notInGroup
unusableNoReason
unusableFailed
usable
active
DEFVAL { notInGroup }
::= { atmImaConfigEntry 2 }
atmImaNeRxState OBJECT-TYPE
SYNTAX INTEGER {
notInGroup(1),
unusableNoReason(2),
unusableFault(3),
unusableMisconnected(4),
unusableInhibited(5),
unusableFailed(6),
usable(7),
active(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTIONro Enumeration .1.3.6.1.4.1.1751.2.18.5.15.1.3 |
atmImaFeTxStateThe far-end transmit state.
notInGroup
unusableNoReason
unusableFailed
usable
active
DEFVAL { notInGroup }
::= { atmImaConfigEntry 4 }
atmImaFeRxState OBJECT-TYPE
SYNTAX INTEGER {
notInGroup(1),
unusableNoReason(2),
unusableFault(3),
unusableMisconnected(4),
unusableInhibited(5),
unusableFailed(6),
usable(7),
active(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTIONro Enumeration .1.3.6.1.4.1.1751.2.18.5.15.1.5 |
atmImaNeRxDefectThe near-end receive defect.
noDefect
linkFailure
lifDefect
(Loss of IMA Frame)
lodsDefect
(Link Out of Delay Synchronization)ro Enumeration .1.3.6.1.4.1.1751.2.18.5.15.1.6 |
atmImaFeRxDefectThe far-end receive defect.
noDefect
linkFailure
lifDefect
(Loss of IMA Frame)
lodsDefect
(Link Out of Delay Synchronization)ro Enumeration .1.3.6.1.4.1.1751.2.18.5.15.1.7 |
atmImaAdminStatusThe administrative action:
'outOfService' take the interface out of service
'inService' take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.15.1.8 |
atmImaOperStatusThe operational status of the interface:
'outOfService' interface is out of service
'inService' interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.15.1.9 |
atmPnniConfigTableTable of atm PNNI Configuration SEQUENCE OF AtmPnniConfigEntry .1.3.6.1.4.1.1751.2.18.5.16 |
atmPnniConfigEntryRow definition of PNNI Configuration AtmPnniConfigEntry .1.3.6.1.4.1.1751.2.18.5.16.1 |
atmPnniIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.16.1.1 |
atmPnniSvcMinVpiThe lower bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.2 |
atmPnniSvcMaxVpiThe upper bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.3 |
atmPnniSvcMinVciThe lower bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.4 |
atmPnniSvcMaxVciThe upper bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.5 |
atmPnniAdminStatusThe administrative action:
'outOfService' means take the PNNI out of service
'inService' means take the PNNI in service
'delete' remove/deconfigure the PNNI.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.6 |
atmPnniOperStatusThe operational status of the PNNI:
'outOfService' means the PNNI is out of service
'inService' means the PNNI is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.7 |
atmPnniT303Timer T303 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.8 |
atmPnniT308Timer T308 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.9 |
atmPnniT309Timer T309 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.10 |
atmPnniT310Timer T310 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.11 |
atmPnniT313Timer T313 value - User side only - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.12 |
atmPnniT316Timer T316 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.13 |
atmPnniT317Timer T317 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.14 |
atmPnniT322Timer T322 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.15 |
atmPnniT397Timer T397 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.16 |
atmPnniT398Timer T398 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.17 |
atmPnniT399Timer T399 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.18 |
atmPnniCbrServCatSuppIf CBR category is supportedrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.19 |
atmPnniCbrGcacClpEqualZeroIf the advertised GCAC parameters apply for CLP=0 or CLP=0+1 trafficrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.20 |
atmPnniCbrMaxCellRateCBR category Maximum Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.21 |
atmPnniCbrAvailCellRateCBR category Available Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.22 |
atmPnniCbrCellXerDelayCBR category Cell Transfer Delayrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.23 |
atmPnniCbrCellLossRatioZeroCBR category Cell Loss Ratio for CLP=0 trafficrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.24 |
atmPnniCbrCellLossRatioZeroPlusOneCBR category Cell Loss Ratio for CLP=0+1 trafficrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.25 |
atmPnniCbrCellDelayVarCBR category Cell Delay Variationrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.26 |
atmPnniRtVbrServCatSuppIf RT VBR category is supportedrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.27 |
atmPnniRtVbrGcacClpEqualZeroIf the advertised GCAC parameters apply for CLP=0 or CLP=0+1 trafficrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.28 |
atmPnniRtVbrMaxCellRateRT VBR category Maximum Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.29 |
atmPnniRtVbrAvailCellRateRT VBR category Available Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.30 |
atmPnniRtVbrCellXerDelayRT VBR category Cell Transfer Delayrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.31 |
atmPnniRtVbrCellLossRatioZeroRT VBR category Cell Loss Ratio for CLP=0 trafficrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.32 |
atmPnniRtVbrCellLossRatioZeroPlusOneRT VBR category Cell Loss Ratio for CLP=0+1 trafficrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.33 |
atmPnniRtVbrCellDelayVarRT VBR category Cell Delay Variationrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.34 |
atmPnniRtVbrGcacPresentIf RT VBR category GCAC Parameters presentrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.35 |
atmPnniRtVbrCellRateMarginRT VBR category Cell Rate Marginrw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.36 |
atmPnniRtVbrVarianceFactorRT VBR category Variance Factorrw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.37 |
atmPnniNrtVbrServCatSuppIf NRT VBR category is supportedrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.38 |
atmPnniNrtVbrGcacClpEqualZeroIf the advertised GCAC parameters apply for CLP=0 or CLP=0+1 trafficrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.39 |
atmPnniNrtVbrMaxCellRateNRT VBR category Maximum Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.40 |
atmPnniNrtVbrAvailCellRateNRT VBR category Available Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.41 |
atmPnniNrtVbrCellXerDelayNRT VBR category Cell Transfer Delayrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.42 |
atmPnniNrtVbrCellLossRatioZeroNRT VBR category Cell Loss Ratio for CLP=0 trafficrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.43 |
atmPnniNrtVbrCellLossRatioZeroPlusOneNRT VBR category Cell Loss Ratio for CLP=0+1 trafficrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.44 |
atmPnniNrtVbrGcacPresentIf NRT VBR category GCAC Parameters presentrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.45 |
atmPnniNrtVbrCellRateMarginNRT VBR category Cell Rate Marginrw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.46 |
atmPnniNrtVbrVarianceFactorNRT VBR category Variance Factorrw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.47 |
atmPnniAbrServCatSuppIf ABR category is supportedrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.48 |
atmPnniAbrMaxCellRateABR category Maximum Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.49 |
atmPnniAbrAvailCellRateABR category Available Cell Raterw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.50 |
atmPnniUbrServCatSuppUBR category Cell Transfer Delayrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.51 |
atmPnniUbrMaxCellRateNRT VBR category Cell Loss Ratio for CLP=0 trafficrw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.52 |
atmPnniOverSubscriptionOver subscription factor for PNNI Intf.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.53 |
atmPnniSgnlEnabledIndicates if atm signaling is enabled or disabled
for this PNNI interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.54 |
atmPnniVpiSigVPI value for the signalling channel for the PNNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.55 |
atmPnniVciSigVCI value for the signalling channel for the PNNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.56 |
atmPnniAvailBwIgrThe Avail Bandwidth for that interface in
cells per sec. Bandwidth for UBR conns
will not be accounted for.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.57 |
atmPnniAvailBwEgrThe Avail Bandwidth for that interface in
cells per sec. Bandwidth for UBR conns
will not be accounted for.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.58 |
atmPnniUPCSuppupc supp off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.59 |
atmPnniUbrLoadBalSuppload balancing supp for ubr conns off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.60 |
atmPnniSscopRxWndSzThe receive window size for the SSCOP layerrw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.61 |
atmPnniRemoteSvcMinVpiThe lower bound of the actual VPI
for SVC connections.ro INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.62 |
atmPnniRemoteSvcMaxVpiThe Upper bound of the actual VPI
for SVC connections.ro INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.63 |
atmPnniRemoteSvcMinVciThe lower bound of the actual VCI for
SVC connections.ro INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.64 |
atmPnniRemoteSvcMaxVciThe Upper bound of the actual VCI for
SVC connections.ro INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.65 |
atmPnniVpiIlmiVPI value for the ilmi channel for
the PNNI interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.66 |
atmPnniVciIlmiVCI value for the ilmi channel for
the PNNI interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.16.1.67 |
atmPnniIlmiProtocolStatusThe administrative status:
'enabled' - ILMI protocol enabled on PNNI
'disabled' - ILMI protocol disabled on PNNI .rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.68 |
atmPnniIlmiOperStatusThe operational status:
'outOfService' - ILMI connectivity is down
'inService' - ILMI connectivity is up.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.69 |
atmPnniIlmiConfigProcILMI Configuration Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.70 |
atmPnniIlmiConnectProcILMI Connectivity Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.71 |
atmPnniIlmiAttachPtProcILMI Attachment Point Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.72 |
atmPnniIlmiSecureLinkProcILMI Secure Link Procedure status.
Can be enabled only if Attachment Point
Procedure is enabled.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.73 |
atmPnniIlmiAddrRegProcILMI Address Registration Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.74 |
atmPnniIlmiTimerSTimer S (secs). Used to poll peer when
link is down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.75 |
atmPnniIlmiTimerTTimer T (secs). Used to poll peer when
link is up.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.76 |
atmPnniIlmiRetryKRetry K - number of timeouts of before
link is declared down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.16.1.77 |
atmPnniConnTrafficShapingFlagTraffic Shaping for Conn was enabled
primarily because the core would lose
cells since we were non-conformant cells.
Therefore the hardware added traffic
shaping per connection. But condition is
VI should not be enabled if this feature
is enabled.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.16.1.78 |
atmVnnConfigTableTable of atm user to network interface (UNI) SEQUENCE OF AtmVnnConfigEntry .1.3.6.1.4.1.1751.2.18.5.17 |
atmVnnConfigEntryRow definition of atm UNI AtmVnnConfigEntry .1.3.6.1.4.1.1751.2.18.5.17.1 |
atmVnnIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.17.1.1 |
atmVnnAddrTypeatm address typerw Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.2 |
atmVnnSvcMinVpiThe lower bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.3 |
atmVnnSvcMaxVpiThe upper bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.4 |
atmVnnSvcMinVciThe lower bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.5 |
atmVnnSvcMaxVciThe upper bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.6 |
atmVnnAdminStatusThe administrative action:
'outOfService' means take the UNI out of service
'inService' means take the UNI in service
'delete' remove/deconfigure the UNI.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.7 |
atmVnnOperStatusThe operational status of the UNI:
'outOfService' means the UNI is out of service
'inService' means the UNI is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.8 |
atmVnnOverSubscriptionOver subscription factorrw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.9 |
atmVnnNwPrefix1ATM Network Prefix 1ro OCTET STRING .1.3.6.1.4.1.1751.2.18.5.17.1.10 |
atmVnnT303Timer T303 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.11 |
atmVnnT308Timer T308 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.12 |
atmVnnT309Timer T309 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.13 |
atmVnnT310Timer T310 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.14 |
atmVnnT313Timer T313 value - User side only - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.15 |
atmVnnT316Timer T316 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.16 |
atmVnnT317Timer T317 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.17 |
atmVnnT322Timer T322 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.18 |
atmVnnT398Timer T398 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.19 |
atmVnnT399Timer T399 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.20 |
atmVnnMyNeighborIpAddressThe IP address of the neighbor system connected to
the far end of this interface, to which a Network
Management Station can send SNMP messages, as IP
datagrams sent to UDP port 161, in order to access
network management information concerning the
operation of that system. Note that the value
of this object can currently only be obtained
by manual configuration.rw IpAddress .1.3.6.1.4.1.1751.2.18.5.17.1.21 |
atmVnnMyNeighborIfNameThe textual name of the interface on the neighbor
system on the far end of this interface, and to
which this interface connects. If the neighbor
system is manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface for this
port. If this interface does not have a
textual name, the value of this object is a zero
length string. Note that the value of this object
can currently only be obtained by manual
configuration.rw DisplayString .1.3.6.1.4.1.1751.2.18.5.17.1.22 |
atmVnnVpiSigVPI value for the signalling channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.23 |
atmVnnVciSigVCI value for the signalling channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.24 |
atmVnnVpiIlmiVPI value for the ilmi channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.25 |
atmVnnVciIlmiVCI value for the ilmi channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.26 |
atmVnnAtmSignalingStatusIndicates if atm signaling is enabled or disabled
for this interface. Consistent with other AC interfacesro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.27 |
atmVnnMyIfNameA textual name of this interface. If this system
is manageable manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface for this
port. This interface must be uniquely named on
this system to distinguish parallel links with a
neighboring system. If this interface does not
have a textual name, the value of this object is a
zero length string.rw DisplayString .1.3.6.1.4.1.1751.2.18.5.17.1.28 |
atmVnnIlmiProtocolStatusThe administrative status:
'enabled' - ILMI protocol enabled on UNI.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.29 |
atmVnnIlmiOperStatusThe operational status:
'outOfService' - ILMI connectivity is down
'inService' - ILMI connectivity is up.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.30 |
atmVnnIlmiConfigProcILMI Configuration Procedure status.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.31 |
atmVnnIlmiConnectProcILMI Connectivity Procedure status.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.32 |
atmVnnIlmiAttachPtProcILMI Attachment Point Procedure status.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.33 |
atmVnnIlmiSecureLinkProcILMI Secure Link Procedure status. Can be enabled
only if Attachment Point Procedure is enabled.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.34 |
atmVnnIlmiAddrRegProcILMI Address Registration Procedure status.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.35 |
atmVnnIlmiTimerSTimer S (secs). Used to poll peer when link is
down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.36 |
atmVnnIlmiTimerTTimer T (secs). Used to poll peer when link is
up.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.37 |
atmVnnIlmiRetryKRetry K - number of timeouts before link is
declared down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.38 |
atmVnnAvailBwIgrThe Avail Bandwidth for that interface in
cells per sec. Bandwidth for UBR conns
will not be accounted for.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.39 |
atmVnnAvailBwEgrThe Avail Bandwidth for that interface in
cells per sec. Bandwidth for UBR conns
will not be accounted for.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.17.1.40 |
atmVnnUPCSuppupc supp off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.41 |
atmVnnUbrLoadBalSuppload balancing supp for ubr conns off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.5.17.1.42 |
atmVnnSscopRxWndSzThe receive window size for the SSCOP layerrw INTEGER .1.3.6.1.4.1.1751.2.18.5.17.1.43 |
virtualIntfConfigTableTable of Virtual Interfaces Configurations SEQUENCE OF VirtualIntfConfigEntry .1.3.6.1.4.1.1751.2.18.5.18 |
virtualIntfConfigEntryIndex is the Interface and the Virutal Interface VirtualIntfConfigEntry .1.3.6.1.4.1.1751.2.18.5.18.1 |
virtualIntfConfigIfInterface index for side A of an ATM-to-ATM PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.5.18.1.1 |
virtualIntfConfigViVI value. Def Val is 1 because 0 cannot be
configured INTEGER .1.3.6.1.4.1.1751.2.18.5.18.1.2 |
virtualIntfConfigCellRateBandwidth assigned for the VI.
The unit is cells per sec.
Total Bandwidth of all VI's
cannot exceed bandwidth of the
main interface. CAC will be supported per VI.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.18.1.3 |
virtualIntfConfigOverSubsOver Subscription rate for VIrw Integer32 .1.3.6.1.4.1.1751.2.18.5.18.1.4 |
virtualIntfConfigRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.5.18.1.5 |
virtualIntfConfigUPCSuppvirtual interface upc supp off/on
If this is changed then all the connections
on this interface will be replayed.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.18.1.6 |
virtualIntfAvailBwEgrAvail Bw for that VI in cells per sec in the
Egress Direction or the direction away
from back plane.ro Integer32 .1.3.6.1.4.1.1751.2.18.5.18.1.7 |
virtualUNIConfigTableTable of Virtual UNI Interfaces Configurations SEQUENCE OF VirtualUNIConfigEntry .1.3.6.1.4.1.1751.2.18.5.19 |
virtualUNIConfigEntryIndex is the Interface and the Virutal UNI Interface VirtualUNIConfigEntry .1.3.6.1.4.1.1751.2.18.5.19.1 |
virtualUNIIfIndexThis is the first index to the Virtual UNI
Interface table. Interface index will be of the form SSPPCCC,
where SS is the card slot, PP is the port number, and CCC
is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.5.19.1.1 |
virtualUNIVUNIIdVirtual UNI number, second index to access the virtual
UNI interface. INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.2 |
virtualUNIVISupportVirtual Interface (Traffic Shaping) is enabled or
disabled on this VUNI. A Virtual Interface should already be
configured befaore the traffic shaping can be enabled on this VUNI. If
VISupport is disabled then all the connections on the VUNI can only be
configured as UBR connections if this VUNI interface is on a VI enabled
physical interfacerw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.3 |
virtualUNIMinVpiLower value of the VPI range for this VUNIrw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.4 |
virtualUNIMaxVpiUpper value of the VPI range for this VUNIrw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.5 |
virtualUNIConfigRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.5.19.1.6 |
virtualUNIAddrTypeatm address typerw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.7 |
virtualUNISvcMinVpiThe lower bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.8 |
virtualUNISvcMaxVpiThe upper bound of the VPI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.9 |
virtualUNISvcMinVciThe lower bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.10 |
virtualUNISvcMaxVciThe upper bound of the VCI for SVC connections.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.11 |
virtualUNIAdminStatusThe administrative action:
'outOfService' means take the VUNI out of service
'inService' means take the VUNI in servicerw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.12 |
virtualUNIOperStatusThe operational status of the VUNI:
'outOfService' means the VUNI is out of service
'inService' means the VUNI is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.13 |
virtualUNINwPrefix1ATM Network Prefix 1rw OCTET STRING .1.3.6.1.4.1.1751.2.18.5.19.1.14 |
virtualUNIT303Timer T303 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.15 |
virtualUNIT308Timer T308 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.16 |
virtualUNIT309Timer T309 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.17 |
virtualUNIT310Timer T310 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.18 |
virtualUNIT313Timer T313 value - User side only - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.19 |
virtualUNIT316Timer T316 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.20 |
virtualUNIT317Timer T317 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.21 |
virtualUNIT322Timer T322 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.22 |
virtualUNIT398Timer T398 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.23 |
virtualUNIT399Timer T399 value - secondsrw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.24 |
virtualUNIMyNeighborIpAddressThe IP address of the neighbor system connected to
the far end of this interface, to which a Network
Management Station can send SNMP messages, as IP
datagrams sent to UDP port 161, in order to access
network management information concerning the
operation of that system. Note that the value
of this object can currently only be obtained
by manual configuration.rw IpAddress .1.3.6.1.4.1.1751.2.18.5.19.1.25 |
virtualUNIMyNeighborIfNameThe textual name of the interface on the neighbor
system on the far end of this interface, and to
which this interface connects. If the neighbor
system is manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface for this
port. If this interface does not have a
textual name, the value of this object is a zero
length string. Note that the value of this object
can currently only be obtained by manual
configuration.rw DisplayString .1.3.6.1.4.1.1751.2.18.5.19.1.27 |
virtualUNIVpiSigVPI value for the signalling channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.28 |
virtualUNIVciSigVCI value for the signalling channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.29 |
virtualUNISignalingAdminStatusIndicates if atm signaling is enabled or disabled
for this VUNI interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.30 |
virtualUNISignalingOperStatusThe protocol operational status of the UNI:
'outOfService' means the UNI is out of service
'inService' means the UNI is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.31 |
virtualUNIVpiIlmiVPI value for the ilmi channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.32 |
virtualUNIVciIlmiVCI value for the ilmi channel for the UNI
interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.33 |
virtualUNIMyIfNameA textual name of this interface. If this system
is manageable manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface for this
port. This interface must be uniquely named on
this system to distinguish parallel links with a
neighboring system. If this interface does not
have a textual name, the value of this object is a
zero length string.rw DisplayString .1.3.6.1.4.1.1751.2.18.5.19.1.34 |
virtualUNIIlmiProtocolStatusThe administrative status:
'enabled' - ILMI protocol enabled on UNI
'disabled' - ILMI protocol disabled on UNI.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.35 |
virtualUNIIlmiOperStatusThe operational status:
'outOfService' - ILMI connectivity is down
'inService' - ILMI connectivity is up.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.36 |
virtualUNIIlmiConfigProcILMI Configuration Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.37 |
virtualUNIIlmiConnectProcILMI Connectivity Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.38 |
virtualUNIIlmiAttachPtProcILMI Attachment Point Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.39 |
virtualUNIIlmiSecureLinkProcILMI Secure Link Procedure status. Can be enabled
only if Attachment Point Procedure is enabled.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.40 |
virtualUNIIlmiAddrRegProcILMI Address Registration Procedure status.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.41 |
virtualUNIIlmiTimerSTimer S (secs). Used to poll peer when link is
down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.42 |
virtualUNIIlmiTimerTTimer T (secs). Used to poll peer when link is
up.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.43 |
virtualUNIIlmiRetryKRetry K - number of timeouts before link is
declared down.rw Integer32 .1.3.6.1.4.1.1751.2.18.5.19.1.44 |
virtualUNIIntfTypeatm interface typerw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.45 |
virtualUNIUserAddressATM User Addressrw OCTET STRING .1.3.6.1.4.1.1751.2.18.5.19.1.46 |
virtualUNIUserAddrOrgScopeATM User Address Organizational scoperw Enumeration .1.3.6.1.4.1.1751.2.18.5.19.1.47 |
virtualUNISscopRxWndSzThe receive window size for the SSCOP layerrw INTEGER .1.3.6.1.4.1.1751.2.18.5.19.1.48 |
casConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.5.20 |
casConfigTableTable for CAS trunk/line configuration. SEQUENCE OF CasConfigEntry .1.3.6.1.4.1.1751.2.18.5.20.1 |
casConfigEntryRow definition for CAS trunk/line configuration. CasConfigEntry .1.3.6.1.4.1.1751.2.18.5.20.1.1 |
casIfIndexThe channel ID (slot/port/channel) in SSPPCCC
format associated with the CAS trunk/line. IntfIndex .1.3.6.1.4.1.1751.2.18.5.20.1.1.1 |
casAdminStatusThe administrative action:
outOfService-take the CAS trunk/line out of service,
inService-take the CAS trunk/line in service,
delete-remove/deconfigure the CAS trunk/line.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.20.1.1.2 |
casOperStatusThe operational status of the CAS trunk/line:
outOfService-the CAS trunk/line is out of service,
inService-the CAS trunk/line is in service.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.20.1.1.3 |
casProtocolTypeThe type of CAS protocol to be used.
The protocol must match the one used on the
other end of the trunk/line.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.20.1.1.4 |
casDirectionThe direction of traffic flow on this CAS
trunk/line.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.20.1.1.5 |
casAddressingTypeThe addressing type used for the CAS trunk/line.
dtmf
r1-mf
r2-mf
Type of 're-mf' is valid only when casProtocolType
is 'wink start', while 'r2-mf' is valid only when
casProtocolType is 'itu-t r2' .rw Enumeration .1.3.6.1.4.1.1751.2.18.5.20.1.1.6 |
casBitPatternTypeThe type of bit pattern used for supervisory
signaling. The value is AB when SF framing is
used, ABCD when ESF framing is used for DS1.
In case of E1, the value is always ABCD.ro Enumeration .1.3.6.1.4.1.1751.2.18.5.20.1.1.7 |
casGroupIdThe identifier to associate a group of CAS
trunks/lines which have same reachability.
When SG is disabled, it must be specified with a
non-zero value. When SG is enabled, the value should
be set to zero which indicate no routing performed
based on the value.rw INTEGER .1.3.6.1.4.1.1751.2.18.5.20.1.1.8 |
toneAnnceConfigTableTable for the Tone Announcement Interface SEQUENCE OF ToneAnnceConfigEntry .1.3.6.1.4.1.1751.2.18.5.21 |
toneAnnceConfigEntryRow definition for Tone Announcement interface ToneAnnceConfigEntry .1.3.6.1.4.1.1751.2.18.5.21.1 |
toneAnnceIfIndexinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.5.21.1.1 |
toneAnnceAdminStatusThe administrative action:
'outOfService' means take the interface out of service
'inService' means take the interface in service
'delete' remove/deconfigure the interface.rw Enumeration .1.3.6.1.4.1.1751.2.18.5.21.1.2 |
toneAnnceOperStatusThe operational status of the interface:
'outOfService' means the interface is out of service
'inService' means the interface is in servicero Enumeration .1.3.6.1.4.1.1751.2.18.5.21.1.3 |
gr303IntfConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.5.22 |
gr303IntfConfigTableTable of GR303 interface configuration attributes SEQUENCE OF Gr303IntfConfigEntry .1.3.6.1.4.1.1751.2.18.5.22.1 |
gr303IntfConfigEntryRow definition for GR303 interface configuration
table Gr303IntfConfigEntry .1.3.6.1.4.1.1751.2.18.5.22.1.1 |
gr303IntfIdInterface ID (SSPPCCC) Integer32 .1.3.6.1.4.1.1751.2.18.5.22.1.1.1 |
gr303TMCChannelIdTMC-Channel Number. If TMC Channel is set to 0
there will be no TMC channel on the
corresponding DS1. Generally the TMC channel
should be specified on the one of the DS1's in a
GR303 interface group and should be on DS0 no.
24rw Integer32 .1.3.6.1.4.1.1751.2.18.5.22.1.1.2 |
gr303EOCChannelIdEOC-Channel Number. If EOC Channel is set to 0
there will be no EOC channel on the
corresponding DS1. Generally the TMC channel
should be specified on the one of the DS1's in a
GR303 interface group and should be on DS0 no.
12rw Integer32 .1.3.6.1.4.1.1751.2.18.5.22.1.1.3 |
gr303IntfAdminStatusGR303 interface admin statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.22.1.1.4 |
gr303IntfOperStatusGR303 interface operational statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.22.1.1.5 |
gr303Ds0ChanConfigTableTable of GR303 DS0 Channel configuration attriburtes SEQUENCE OF Gr303Ds0ChanConfigEntry .1.3.6.1.4.1.1751.2.18.5.22.2 |
gr303Ds0ChanConfigEntryRow definition for GR303 DS0 Channel configuration
table Gr303Ds0ChanConfigEntry .1.3.6.1.4.1.1751.2.18.5.22.2.1 |
gr303Ds0ChanIdGR303 DS0 Chan ID (SSPPCCC) Integer32 .1.3.6.1.4.1.1751.2.18.5.22.2.1.1 |
gr303Ds0ChanAdminStatusGR303 Ds0 Chan admin statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.22.2.1.2 |
gr303Ds0ChanOperStatusGR303 Ds0 Chan operational statusrw Enumeration .1.3.6.1.4.1.1751.2.18.5.22.2.1.3 |
connectionConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.6 |
atmPvcVccTableTable of PVC atm virtual channel connections SEQUENCE OF AtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.1 |
atmPvcVccEntryRow definition of atm PVC VCC connections AtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.1.1 |
atmPvcVccIfAInterface index for side A of an ATM-to-ATM PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.1.1.1 |
atmPvcVccVpiAVPI value for side A of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.2 |
atmPvcVccVciAVCI value for side A of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.3 |
atmPvcVccIfBInterface index for side B of an ATM-to-ATM PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.1.1.4 |
atmPvcVccVpiBVPI value for side B of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.5 |
atmPvcVccVciBVCI value for side B of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.6 |
atmPvcVccServiceTypeA2Bservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.7 |
atmPvcVccSarTypeA2BSAR type used in atm adaptionrw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.8 |
atmPvcVccPeakCellRateA2Bpeak cell rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.1.1.10 |
atmPvcVccSusCellRateA2Bsustained rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.1.1.11 |
atmPvcVccMaxBurstSizeA2Bmaximum burst size - side A, in cellsrw Integer32 .1.3.6.1.4.1.1751.2.18.6.1.1.12 |
atmPvcVccServiceTypeB2Aservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.13 |
atmPvcVccSarTypeB2Asar type used in atm adaptionrw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.14 |
atmPvcVccPeakCellRateB2Apeak rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.1.1.16 |
atmPvcVccSusCellRateB2Asustained rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.1.1.17 |
atmPvcVccMaxBurstSizeB2Amaximum burst size - side B, in cells.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.1.1.18 |
atmPvcVccTypetype of connectionrw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.20 |
atmPvcVccFlowtype of flowrw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.21 |
atmPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.1.1.22 |
atmPvcVccFrwdErrCorrectionA2BForward error correction schemerw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.23 |
atmPvcVccFrwdErrCorrectionB2AForward error correction schemerw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.24 |
atmPvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.25 |
atmPvcVccOamStatusIndicates the OAM monitoring status of side A.
The 5 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
it will respond to AIS/RDI.
Seg-Pt: A side is only a segment point, therefore
it will only respond to maintenance OAM cells
and not fault cells.
End-Seg-Pt: A side is both an end point and a
segment point.
Intermediate-Pt: It will only generate AIS during
local failure.
For ATM-to-ATM connections the OAM status will be
symmetric on both sides of the connection.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.26 |
atmPvcVccDualHomedDoes this PVC need a backup Dual homing PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.27 |
atmPvcVccViAVI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.28 |
atmPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.29 |
atmPvcVccCnfrmTypeA2BThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one_bucket_notag_0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two_bucket_notag_0plus1_0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two_bucket_notag_0plus1_0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two_bucket_tag_0plus1_0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best_effort_tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.30 |
atmPvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one_bucket_notag_0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two_bucket_notag_0plus1_0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two_bucket_notag_0plus1_0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two_bucket_tag_0plus1_0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best_effort_tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.31 |
atmPvcVccVUNIAVUNI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.32 |
atmPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.33 |
atmPvcVccOamStatusBIndicates the Oam monitoring status of side B
of an internal connection. Refer to ITU I.610 and
Bellcore GR1248-CORE for definitions.
The 6 possible states are:
Unsupp: No OAM cell monitoring or generation
enabled. All OAM flows are transparently
passed through.
End-Pt: Connection endPoint, segment flows are
discarded.
Seg-Pt: Segment endPoint.
End-Seg-Pt: Connection endPoint that is also
a segment endPoint.
Intermediate-Pt: Connecting point, that is
outside any segment. Generates only ete
flows.
Intra-Segment-Pt: Connecting point with a segment.
Generates ete as well as segment flows.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.34 |
atmPvcVccOAMConnEndPtStatusAConnection endpoint side A status. Valid only at
connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.35 |
atmPvcVccOAMConnEndPtStatusBConnection endpoint side B status. Valid only at
connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.36 |
atmPvcVccOAMConnSegEndPtStatusASegment endpoint side A status. Valid only at
segment endpoints.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.37 |
atmPvcVccOAMConnSegEndPtStatusBSegment endpoint side B status. Valid only at
segment endpoints.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.38 |
atmPvcVccMfsA2BMaximum Frame Size for GFR traffic for A2B dirrw INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.39 |
atmPvcVccMfsB2AMaximum Frame Size for GFR traffic for B2A dirrw INTEGER .1.3.6.1.4.1.1751.2.18.6.1.1.40 |
atmPvcVccConnFailureCauseAconnestion status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.1.1.41 |
atmPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.1.1.42 |
atmPvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.43 |
atmPvcVccTrafficShapingB2ATraffic Shaping Support in the B2A direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.1.1.44 |
atmPvcVpcTableTable of PVC atm virtual path connections SEQUENCE OF AtmPvcVpcEntry .1.3.6.1.4.1.1751.2.18.6.2 |
atmPvcVpcEntryRow definition of atm connections AtmPvcVpcEntry .1.3.6.1.4.1.1751.2.18.6.2.1 |
atmPvcVpcIfAInterface index for side A of an ATM-to-ATM PVC VPC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.2.1.1 |
atmPvcVpcVpiAVPI value for side A of an ATM-to-ATM PVC VPC
connection. Valid range is a number between 0 and
4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.2.1.2 |
atmPvcVpcIfBInterface index for side B of an ATM-to-ATM PVC VPC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.2.1.3 |
atmPvcVpcVpiBVPI value for side B of an ATM-to-ATM PVC VPC
connection. Valid range is a number between 0 and
4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.2.1.4 |
atmPvcVpcServiceTypeA2Bservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.5 |
atmPvcVpcSarTypeA2BSAR Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.6 |
atmPvcVpcPeakCellRateA2Bpeak rate - side A, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.2.1.8 |
atmPvcVpcSusCellRateA2Bsustained rate - side A, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.2.1.9 |
atmPvcVpcMaxBurstSizeA2Bmaximum burst size - side A, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.2.1.10 |
atmPvcVpcServiceTypeB2Aservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.11 |
atmPvcVpcSarTypeB2ASAR Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.12 |
atmPvcVpcPeakCellRateB2Apeak rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.2.1.14 |
atmPvcVpcSusCellRateB2Asustained rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.2.1.15 |
atmPvcVpcMaxBurstSizeB2Amaximum burst size - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.2.1.16 |
atmPvcVpcTypesecurity feature typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.17 |
atmPvcVpcFlowflow typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.18 |
atmPvcVpcRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.2.1.19 |
atmPvcVpcConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.20 |
atmPvcVpcOamStatusIndicates the OAM monitoring status of side A.
The 5 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
it will respond to AIS/RDI.
Seg-Pt: A side is only a segment point, therefore
it will only respond to maintenance OAM cells
and not fault cells.
End-Seg-Pt: A side is both an end point and a
segment point.
Intermediate-Pt: It will only generate AIS during
local failure.
For ATM-to-ATM connections the OAM status will be
symmetric on both sides of the connection.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.21 |
atmPvcVpcDualHomedDoes this PVC need a backup Dual homing PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.22 |
atmPvcVpcViAVI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.2.1.23 |
atmPvcVpcViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.2.1.24 |
atmPvcVpcCnfrmTypeA2BThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.25 |
atmPvcVpcCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.26 |
atmPvcVpcVUNIAVUNI Id to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.2.1.27 |
atmPvcVpcVUNIBVUNI Id to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.2.1.28 |
atmPvcVpcOamStatusBIndicates the Oam monitoring status of side B
of an internal connection. Refer to ITU I.610 and
Bellcore GR1248-CORE for definitions.
The 6 possible states are:
Unsupp: No OAM cell monitoring or generation
enabled. All OAM flows are transparently
passed through.
End-Pt: Connection endPoint, segment flows are
discarded.
Seg-Pt: Segment endPoint.
End-Seg-Pt: Connection endPoint that is also a
segment endPoint.
Intermediate-Pt: Connecting point, that is outside
any segment. Generates only ete flows.
Intra-Segment-Pt: Connecting point with a segment.
Generates ete as well as segment flows.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.29 |
atmPvcVpcOAMConnEndPtStatusAConnection endpoint side A status. Valid only
at connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.30 |
atmPvcVpcOAMConnEndPtStatusBConnection endpoint side B status. Valid only at
connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.31 |
atmPvcVpcOAMConnSegEndPtStatusASegment endpoint side A status. Valid only at
segment/connection endpoints.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.32 |
atmPvcVpcOAMConnSegEndPtStatusBSegment endpoint side B status. Valid only at
segment/connection endpoints.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.33 |
atmPvcVpcConnFailureCauseAconnestion status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.2.1.34 |
atmPvcVpcConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.2.1.35 |
atmPvcVpcTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.36 |
atmPvcVpcTrafficShapingB2ATraffic Shaping Support in the B2A direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.2.1.37 |
atmSvcVccTableTable of atm connections SEQUENCE OF AtmSvcVccEntry .1.3.6.1.4.1.1751.2.18.6.3 |
atmSvcVccEntryRow definition of atm connections AtmSvcVccEntry .1.3.6.1.4.1.1751.2.18.6.3.1 |
atmSvcVccIfAinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.6.3.1.1 |
atmSvcVccVpiAatm path identifier - side A INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.2 |
atmSvcVccVciAatm channel identifier - side A INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.3 |
atmSvcVccIfBinterface index (slot/port/channel) SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.6.3.1.4 |
atmSvcVccVpiBatm path identifier - side B INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.5 |
atmSvcVccVciBatm channel identifier - side B INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.6 |
atmSvcVccServiceTypeA2Bservice typero Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.7 |
atmSvcVccSarTypeA2Bsar type - A to B directionro Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.8 |
atmSvcVccPeakCellRateA2Bpeak rate - side Aro Integer32 .1.3.6.1.4.1.1751.2.18.6.3.1.10 |
atmSvcVccSusCellRateA2Bsustained rate - side Aro Integer32 .1.3.6.1.4.1.1751.2.18.6.3.1.11 |
atmSvcVccMaxBurstSizeA2Bmaximum burst size - side Aro Integer32 .1.3.6.1.4.1.1751.2.18.6.3.1.12 |
atmSvcVccServiceTypeB2Aservice typero Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.13 |
atmSvcVccSarTypeB2Asar type - B to A directionro Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.14 |
atmSvcVccPeakCellRateB2Apeak rate - side Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.3.1.16 |
atmSvcVccSusCellRateB2Asustained rate - side Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.3.1.17 |
atmSvcVccMaxBurstSizeB2Amaximum burst size - side Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.3.1.18 |
atmSvcVccFlowflow typero Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.19 |
atmSvcVccTypetype of connectionro Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.20 |
atmSvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.21 |
atmSvcVccViAVI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.22 |
atmSvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.23 |
atmSvcVccCnfrmTypeA2BThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.24 |
atmSvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.25 |
atmSvcVccVUNIAVUNI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.26 |
atmSvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.3.1.27 |
atmSvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.28 |
atmSvcVccTrafficShapingB2ATraffic Shaping Support in the B2A direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.3.1.29 |
ipAtmAppPvcVccTableTable about in-band management atm connection
entries. SEQUENCE OF IpAtmAppPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.4 |
ipAtmAppPvcVccEntryRow definition of in-band management
atm connection attribution. IpAtmAppPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.4.1 |
ipAtmAppPvcVccDestAddrADestination IP address of an in-band management-
atm connection. Value is and IP address. IpAddress .1.3.6.1.4.1.1751.2.18.6.4.1.1 |
ipAtmAppPvcVccSubnetMaskAThe subnet mask of the destination IP address.
Value is an IP address. IpAddress .1.3.6.1.4.1.1751.2.18.6.4.1.2 |
ipAtmAppPvcVccIfBInterface index for side B, the atm side, of an
in-band management-atm connection. Number value
is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. Integer32 .1.3.6.1.4.1.1751.2.18.6.4.1.3 |
ipAtmAppPvcVccVpiBVPI value for side B, the atm side, of an
in-band management-atm connection. Valid range
is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.4.1.4 |
ipAtmAppPvcVccVciBVCI value for side B, the atm side, of an
in-band management-atm connection. Valid range
is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.4.1.5 |
ipAtmAppPvcVccServiceTypeA2BService type from side A to Brw Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.6 |
ipAtmAppPvcVccServiceTypeB2AService type from side B to Arw Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.7 |
ipAtmAppPvcVccPeakCellRateB2Apeak rate - side Brw Integer32 .1.3.6.1.4.1.1751.2.18.6.4.1.8 |
ipAtmAppPvcVccSusCellRateB2Asustained rate - side Brw Integer32 .1.3.6.1.4.1.1751.2.18.6.4.1.9 |
ipAtmAppPvcVccMaxBurstSizeB2Amaximum burst size - side Brw Integer32 .1.3.6.1.4.1.1751.2.18.6.4.1.10 |
ipAtmAppPvcVccTypeIndicated in-band management atm
connection type.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.11 |
ipAtmAppPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.4.1.12 |
ipAtmAppPvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.13 |
ipAtmAppPvcVccDualHomedDoes this PVC need a backup Dual homing PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.14 |
ipAtmAppPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.4.1.15 |
ipAtmAppPvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.16 |
ipAtmAppPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.4.1.17 |
ipAtmAppPvcVccMfsB2AMaximum Frame Size for GFR trafficrw INTEGER .1.3.6.1.4.1.1751.2.18.6.4.1.18 |
ipAtmAppPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.4.1.19 |
ipAtmAppPvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.20 |
ipAtmAppPvcVccOamStatusIndicates the OAM monitoring status.
The 3 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
it will respond to AIS/RDI.
End-Seg-Pt: Connection endPoint that is also
a segment endPoint.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.4.1.21 |
ipAtmAppSvcVccTableTable of SVC VCC connection entries SEQUENCE OF IpAtmAppSvcVccEntry .1.3.6.1.4.1.1751.2.18.6.5 |
ipAtmAppSvcVccEntryRow definition of SVC VCC connection
attribution. IpAtmAppSvcVccEntry .1.3.6.1.4.1.1751.2.18.6.5.1 |
ipAtmAppSvcVccDestAddrADestination IP address,value is IP address. IpAddress .1.3.6.1.4.1.1751.2.18.6.5.1.1 |
ipAtmAppSvcVccSubnetMaskAThe subnet mask of the destination IP address.
Value is an IP address. IpAddress .1.3.6.1.4.1.1751.2.18.6.5.1.2 |
ipAtmAppSvcVccIfBinterface index (slot/port/channel) SSPPCCC Integer32 .1.3.6.1.4.1.1751.2.18.6.5.1.3 |
ipAtmAppSvcVccVpiBatm path identifier - side B INTEGER .1.3.6.1.4.1.1751.2.18.6.5.1.4 |
ipAtmAppSvcVccVciBatm channel identifier - side B INTEGER .1.3.6.1.4.1.1751.2.18.6.5.1.5 |
ipAtmAppSvcVccServiceTypeA2BService type from side A to B.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.5.1.6 |
ipAtmAppSvcVccServiceTypeB2AService type from side B to A.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.5.1.7 |
ipAtmAppSvcVccPeakCellRateB2Apeak rate - side Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.5.1.8 |
ipAtmAppSvcVccSusCellRateB2Asustained rate - side Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.5.1.9 |
ipAtmAppSvcVccMaxBurstSizeB2Amaximum burst size - side Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.5.1.10 |
ipAtmAppSvcVccTypeType of using SVC VCC connection.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.5.1.11 |
ipAtmAppSvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.5.1.12 |
ipAtmAppSvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.5.1.13 |
ipAtmAppSvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.5.1.14 |
ipAtmAppSvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.5.1.15 |
ipAtmAppSvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.5.1.16 |
cirEmAtmPvcVccTableTable of Circuit Emulation to ATM VCCs SEQUENCE OF CirEmAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.6 |
cirEmAtmPvcVccEntryRow definition of circuit emulation to atm
connections. CirEmAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.6.1 |
cirEmAtmPvcVccIfAInterface index for side A, the circuit emulation
side, of a circuit emulation-atm PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.6.1.1 |
cirEmAtmPvcVccIfBInterface index for side B, the atm side, of a
circuit emulation-atm PVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.6.1.2 |
cirEmAtmPvcVccVpiBVPI value for side B, the atm side, of a
circuit emulation-atm PVC VCC connection. Valid
range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.6.1.3 |
cirEmAtmPvcVccVciBVCI value for side B, the atm side, of a
circuit emulation-atm PVC VCC connection. Valid
range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.6.1.4 |
cirEmAtmPvcVccServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.5 |
cirEmAtmPvcVccVoiceCompressionA2BVoice Compression Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.6 |
cirEmAtmPvcVccSilenceDetectionA2Bsilence detection off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.7 |
cirEmAtmPvcVccEchoCancellationA2BEcho Cancellation Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.8 |
cirEmAtmPvcVccFlowFlow Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.9 |
cirEmAtmPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.6.1.10 |
cirEmAtmPvcVccCngToneDetectionA2BCalling Tone Detection Algorithm,
one of the enum value, g726-32k(3)
is obsoleted on 01Mar99 such that
user would not be able to configure
CE-ATM.Fax Relay is to allow detection
of fax Calling Tones. In faxRelay Mode
only Fax calling tone is detected . In
fxRlyMdmBypass faxRelay is detected
and Modem is done in bypass moderw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.11 |
cirEmAtmPvcVccCodingTranslationA2BCoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.12 |
cirEmAtmPvcVccVoiceCompressionB2AVoice Compression Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.13 |
cirEmAtmPvcVccSilenceDetectionB2Asilence detection off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.14 |
cirEmAtmPvcVccEchoCancellationB2AEcho Cancellation Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.15 |
cirEmAtmPvcVccCngToneDetectionB2ACalling Tone Detection Algorithm,
one of the enum value, g726-32k(3)
is obsoleted on 01Mar99 such that
user would not be able to configure
CE-ATM.Fax Relay is to allow detection
of fax Calling Tones. In faxRelay Mode
only Fax calling tone is detected . In
fxRlyMdmBypass faxRelay is detected
and Modem is done in bypass moderw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.16 |
cirEmAtmPvcVccCodingTranslationB2ACoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.17 |
cirEmAtmPvcVccSarTypeBThis field will only be used when selecting voice
compression, in other cases it will be set to
aal1.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.18 |
cirEmAtmPvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.19 |
cirEmAtmPvcVccDualHomedDoes this PVC need a backup Dual homing PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.20 |
cirEmAtmPvcVccOamStatusIndicates the OAM monitoring status of side A.
The 2 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
it will respond to AIS/RDI.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.21 |
cirEmAtmPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.6.1.22 |
cirEmAtmPvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.23 |
cirEmAtmPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.6.1.24 |
cirEmAtmPvcVccAal2CidAal2 Cid Used to pack ce chan in an
Atm Trunk. This value will be unique
per Atm Trunk. This field will be applicable
when Aal type is chosen to be Standard Aal2.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.6.1.25 |
cirEmAtmPvcVccOAMConnEndPtStatusConnection endpoint status. Valid only
at connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.26 |
cirEmAtmPvcVccOAMConnSegEndPtStatusSegment endpoint status. Valid only at
segment/connection endpoints.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.27 |
cirEmAtmPvcVccConnFailureCauseAconnestion status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.6.1.28 |
cirEmAtmPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.6.1.29 |
cirEmAtmPvcVccDigitCollectTypeA2BIdentify the digital tone setting.
dtmf
mf
mf-r2-frwd
mf-r2-bkwd
DEFVAL { none }
::= { cirEmAtmPvcVccEntry 30 }
cirEmAtmPvcVccDigitCollectTypeB2A OBJECT-TYPE
SYNTAX INTEGER {
none(1),
dtmf(2),
mf(3),
mf-r2-frwd(4),
mf-r2-bkwd(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTIONrw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.31 |
cirEmAtmPvcVccEncodingStdA2BThese are profiles defined according to standards
User-Profile - No restrictions or checks, user
freedom to choose any combination
of Params.
Atm Forum - These are profies defined by AF in
document AF-VMOA-0145.000. In these
cases the Identifiers are used and
not the table numbers.
Itu-t - These profiles are used from the I-366-2.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.32 |
cirEmAtmPvcVccEncodingStdB2AThese are profiles defined according to standards
User-Profile - No restrictions or checks, user
freedom to choose any combination
of Params.
Atm Forum - These are profies defined by AF in
document AF-VMOA-0145.000. In these
cases the Identifiers are used and
not the table numbers.
Itu-t - These profiles are used from the I-366-2.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.6.1.33 |
cirEmAtmPvcVccEncodingProfileIdA2BThese are profiles defined according to standards
User-Profile - No restrictions or checks, user
freedom to choose any combination
of Params.
Atm Forum - These are profies defined by AF in
document AF-VMOA-0145.000. In these
cases the Identifiers are used and
not the table numbers.
Itu-t - These profiles are used from the I-366-2.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.6.1.34 |
cirEmAtmPvcVccEncodingProfileIdB2AThese are profiles defined according to standards
User-Profile - No restrictions or checks, user
freedom to choose any combination
of Params.
Atm Forum - These are profies defined by AF in
document AF-VMOA-0145.000. In these
cases the Identifiers are used and
not the table numbers.
Itu-t - These profiles are used from the I-366-2.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.6.1.35 |
frAtmPvcVccTableTable of frame relay to ATM IWF connections SEQUENCE OF FrAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.7 |
frAtmPvcVccEntryRow definition of frame relay to ATM IWF
connections FrAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.7.1 |
frAtmPvcVccIfAInterface index for side A, the frame relay side,
of a frame relay-atm PVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.7.1.1 |
frAtmPvcVccDlciADLCI value for side A, the frame relay side,
of a frame relay-atm PVC VCC connection. Valid
range is a number between 0 and 1023. Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.2 |
frAtmPvcVccIfBInterface index for side B, the atm side, of a
frame relay-atm PVC VCC connection. Number value
is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.7.1.3 |
frAtmPvcVccVpiBVPI value for side B, the atm side, of a frame
relay-atm PVC VCC connection. Valid range is a
number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.7.1.4 |
frAtmPvcVccVciBVCI value for side B, the atm side, of a frame
relay-atm PVC VCC connection. Valid range is a
number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.7.1.5 |
frAtmPvcVccMaxFrameSizeInThe value of this object is the size in octets of
the largest frame relay information field for this
PVC in the ingress direction (out of the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.6 |
frAtmPvcVccBcInThe value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this PVC in the ingress
direction (into the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.7 |
frAtmPvcVccBeInThe value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this PVC in the ingress direction (into
the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.8 |
frAtmPvcVccCirInThe value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this PVC
in the ingress direction (into the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.9 |
frAtmPvcVccMaxFrameSizeOutThe value of this object is the size in octets of
the largest frame relay information field for this
PVC in the egress direction (out of the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.10 |
frAtmPvcVccBcOutThe value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this PVC in the egress
direction (into the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.11 |
frAtmPvcVccBeOutThe value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this PVC in the egress direction (into
the frame relay UNI)rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.12 |
frAtmPvcVccCirOutThe value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this PVC
in the egress direction (into the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.13 |
frAtmPvcVccServiceTypeservice type, Frame relay traffic is carried
by VBR type of service only.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.14 |
frAtmPvcVccFlowFlow Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.15 |
frAtmPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.7.1.16 |
frAtmPvcVccTimeLenInThe time interval over which CIR and the burst
sizes (Bc and Be) are measured in the A2B
direction. The unit is milliseconds.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.7.1.17 |
frAtmPvcVccInterWorkingFuncInInterWorking function.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.18 |
frAtmPvcVccTimeLenOutThe time interval over which CIR and the burst
sizes (Bc and Be) are measured in the A2B
direction. The unit is milliseconds.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.7.1.19 |
frAtmPvcVccInterWorkingFuncOutInterWorking function.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.20 |
frAtmPvcVccPeakCellRateA2BPeak cell rate - side A, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.21 |
frAtmPvcVccSusCellRateA2BSustained cell rate - side A, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.22 |
frAtmPvcVccMaxBurstSizeA2BMaximum burst size - side A, in cells,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.23 |
frAtmPvcVccPeakCellRateB2APeak cell rate - side B, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.24 |
frAtmPvcVccSusCellRateB2ASustained cell rate - side B, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.25 |
frAtmPvcVccMaxBurstSizeB2AMaximum burst size - side B, in cells,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.7.1.26 |
frAtmPvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.27 |
frAtmPvcVccDualHomedDoes this PVC need a backup Dual homing PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.28 |
frAtmPvcVccOamStatusIndicates the OAM monitoring status of side A.
The 2 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
it will respond to AIS/RDI.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.29 |
frAtmPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.7.1.30 |
frAtmPvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.31 |
frAtmPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.7.1.32 |
frAtmPvcVccOAMConnEndPtStatusConnection endpoint status. Valid only
at connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.33 |
frAtmPvcVccOAMSegEndPtStatusSegment endpoint status. Valid only at
segment/connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.34 |
frAtmPvcVccMfsB2AMaximum Frame Size for GFR trafficrw INTEGER .1.3.6.1.4.1.1751.2.18.6.7.1.35 |
frAtmPvcVccConnFailureCauseAconnestion status reason codero FrConnFailureCause .1.3.6.1.4.1.1751.2.18.6.7.1.36 |
frAtmPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.7.1.37 |
frAtmPvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.7.1.38 |
frFrPvcTableTable of frame relay to frame relay connections SEQUENCE OF FrFrPvcEntry .1.3.6.1.4.1.1751.2.18.6.8 |
frFrPvcEntryRow definition of frame relay to frame relay PVC
connections FrFrPvcEntry .1.3.6.1.4.1.1751.2.18.6.8.1 |
frFrPvcIfAInterface index for side A of a frame relay-frame
relay PVC connection. Number value is interpreted
as an interface of the form, SSPPCCC, where SS is
the card slot, PP is the port number, and CCC is
the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.8.1.1 |
frFrPvcDlciADLCI value for side A of a frame relay-frame relay
PVC connection. Valid range is a number between
0 and 1023. Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.2 |
frFrPvcIfBInterface index for side B of a frame relay-frame
relay PVC connection. Number value is interpreted
as an interface of the form, SSPPCCC, where SS is
the card slot, PP is the port number, and CCC is
the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.8.1.3 |
frFrPvcDlciBDLCI value for side B of a frame relay-frame relay
PVC connection. Valid range is a number between
0 and 1023. Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.4 |
frFrPvcMaxFrameSizeA2BThe value of this object is the size in octets of
the largest frame relay information field for this
PVC in the A to B direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.5 |
frFrPvcBcA2BThe value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this PVC in the A to B direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.6 |
frFrPvcBeA2BThe value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this PVC in the A to B direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.7 |
frFrPvcCirA2BThe value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this PVC
in the A to B direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.8 |
frFrPvcMaxFrameSizeB2AThe value of this object is the size in octets of
the largest frame relay information field for this
PVC in the B to A direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.9 |
frFrPvcBcB2AThe value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this PVC in the B to A direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.10 |
frFrPvcBeB2AThe value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this PVC in the B to A direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.11 |
frFrPvcCirB2AThe value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this PVC
in the B to A direction.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.12 |
frFrPvcServiceTypeservice type, Frame relay traffic is carried
by VBR type of service only.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.8.1.13 |
frFrPvcFlowFlow Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.8.1.14 |
frFrPvcRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.8.1.15 |
frFrPvcTimeLenA2BThe time interval over which CIR and the burst
sizes (Bc and Be) are measured in the A2B
direction. The unit is milliseconds.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.8.1.16 |
frFrPvcInterWorkingFuncA2BInterWorking function.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.8.1.17 |
frFrPvcTimeLenB2AThe time interval over which CIR and the burst
sizes (Bc and Be) are measured in the A2B
direction. The unit is milliseconds.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.8.1.18 |
frFrPvcInterWorkingFuncB2AInterWorking function.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.8.1.19 |
frFrPvcPeakCellRateA2BPeak cell rate - side A, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.20 |
frFrPvcSusCellRateA2BSustained cell rate - side A, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.21 |
frFrPvcMaxBurstSizeA2BMaximum burst size - side A, in cells,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.22 |
frFrPvcPeakCellRateB2APeak cell rate - side B, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.23 |
frFrPvcSusCellRateB2ASustained cell rate - side B, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.24 |
frFrPvcMaxBurstSizeB2AMaximum burst size - side B, in cells,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.8.1.25 |
frFrPvcConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.8.1.26 |
frFrPvcConnFailureCauseAconnestion status reason codero FrConnFailureCause .1.3.6.1.4.1.1751.2.18.6.8.1.27 |
frFrPvcConnFailureCauseBconnection status reason codero FrConnFailureCause .1.3.6.1.4.1.1751.2.18.6.8.1.28 |
vbrAtmPvcVccTableTable of terminal emulation to ATM network
IWF connections SEQUENCE OF VbrAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.9 |
vbrAtmPvcVccEntryRow definition of terminal emulation to ATM
network IWF connections VbrAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.9.1 |
vbrAtmPvcVccIfAInterface index for side A, the variable bit rate
side, of a variable bit rate-atm PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.9.1.1 |
vbrAtmPvcVccIfBInterface index for side B, the atm side, of a
variable bit rate-atm PVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.9.1.2 |
vbrAtmPvcVccVpiBVPI value for side B, the atm side, of a variable
bit rate-atm PVC VCC connection. Valid range is a
number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.9.1.3 |
vbrAtmPvcVccVciBVCI value for side B, the atm side, of a variable
bit rate-atm PVC VCC connection. Valid range is a
number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.9.1.4 |
vbrAtmPvcVccServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.5 |
vbrAtmPvcVccPeakCellRateA2Bpeak cell rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.9.1.6 |
vbrAtmPvcVccSusCellRateA2Bsustained rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.9.1.7 |
vbrAtmPvcVccMaxBurstSizeA2Bmaximum burst size - side A, in cellsrw Integer32 .1.3.6.1.4.1.1751.2.18.6.9.1.8 |
vbrAtmPvcVccPeakCellRateB2Apeak rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.9.1.9 |
vbrAtmPvcVccSusCellRateB2Asustained rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.9.1.10 |
vbrAtmPvcVccMaxBurstSizeB2Amaximum burst size - side B, in cells.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.9.1.11 |
vbrAtmPvcVccFlowFlow typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.12 |
vbrAtmPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.9.1.13 |
vbrAtmPvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC.
These interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.14 |
vbrAtmPvcVccDualHomedDoes this PVC need a backup Dual homing PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.15 |
vbrAtmPvcVccOamStatusIndicates the OAM monitoring status of side A.
The 2 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
it will respond to AIS/RDI.
End-Seg-Pt: Connection endPoint that is also
a segment endPoint.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.16 |
vbrAtmPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.9.1.17 |
vbrAtmPvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.18 |
vbrAtmPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.9.1.19 |
vbrAtmPvcVccOAMConnEndPtStatusConnection endpoint status. Valid only
at connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.20 |
vbrAtmPvcVccOAMSegEndPtStatusSegment endpoint status. Valid only at
segment/connection endpoint.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.21 |
vbrAtmPvcVccMfsB2AMaximum Frame Size for GFR trafficrw INTEGER .1.3.6.1.4.1.1751.2.18.6.9.1.22 |
vbrAtmPvcVccConnFailureCauseAconnestion status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.9.1.23 |
vbrAtmPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.9.1.24 |
vbrAtmPvcVccSarTypeBThis field will be used to connect hdlc
to atm directly when sar type is none or aal5 or
go through dsp2 first when sar type is aal2Std.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.25 |
vbrAtmPvcVccAal2CidAal2 Cid Used to pack hdlc chan in an
Atm Trunk. This value will be unique
per Atm Trunk. This field will be applicable
when Aal type is chosen to be Standard Aal2.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.9.1.26 |
vbrAtmPvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.9.1.27 |
cirEmCirEmPvcTableTable of Circuit Emulation to Circuit Emulation SEQUENCE OF CirEmCirEmPvcEntry .1.3.6.1.4.1.1751.2.18.6.10 |
cirEmCirEmPvcEntryRow definition of circuit emulation to
circuit emulation connections. CirEmCirEmPvcEntry .1.3.6.1.4.1.1751.2.18.6.10.1 |
cirEmCirEmPvcIfAInterface index for side A of a circuit
emulation-circuit emulation PVC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.10.1.1 |
cirEmCirEmPvcIfBInterface index for side B of a circuit
emulation-circuit emulation PVC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.10.1.2 |
cirEmCirEmPvcEchoCancellationA2BEcho cancellation off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.5 |
cirEmCirEmPvcFlowFlow Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.6 |
cirEmCirEmPvcRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.10.1.7 |
cirEmCirEmPvcCodingTranslationA2BCoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.8 |
cirEmCirEmPvcEchoCancellationB2AEcho cancellation off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.9 |
cirEmCirEmPvcCodingTranslationB2ACoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.10 |
cirEmCirEmPvcConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.11 |
cirEmCirEmPvcInterworkingCE - CE interworking enable/disabledrw Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.12 |
cirEmCirEmPvcServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.10.1.13 |
cirEmCirEmPvcConnFailureCauseAconnestion status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.10.1.14 |
cirEmCirEmPvcConnFailureCauseBconnection status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.10.1.15 |
vbrVbrPvcTableTable of terminal emulation to ATM network
IWF connections SEQUENCE OF VbrVbrPvcEntry .1.3.6.1.4.1.1751.2.18.6.11 |
vbrVbrPvcEntryRow definition of terminal emulation to ATM
network IWF connections VbrVbrPvcEntry .1.3.6.1.4.1.1751.2.18.6.11.1 |
vbrVbrPvcIfAInterface index for side A of a variable bit
rate-variable bit rate PVC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.11.1.1 |
vbrVbrPvcIfBInterface index for side B of a variable bit
rate-variable bit rate PVC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.11.1.2 |
vbrVbrPvcPeakCellRateA2Bpeak cell rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.11.1.3 |
vbrVbrPvcSusCellRateA2Bsustained rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.11.1.4 |
vbrVbrPvcMaxBurstSizeA2Bmaximum burst size - side A, in cellsrw Integer32 .1.3.6.1.4.1.1751.2.18.6.11.1.5 |
vbrVbrPvcPeakCellRateB2Apeak rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.11.1.6 |
vbrVbrPvcSusCellRateB2Asustained rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.11.1.7 |
vbrVbrPvcMaxBurstSizeB2Amaximum burst size - side B, in cells.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.11.1.8 |
vbrVbrPvcFlowFlow Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.11.1.9 |
vbrVbrPvcRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.11.1.10 |
vbrVbrPvcConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.11.1.11 |
vbrVbrPvcServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.11.1.12 |
vbrVbrPvcConnFailureCauseAconnestion status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.11.1.13 |
vbrVbrPvcConnFailureCauseBconnection status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.11.1.14 |
bridgeBridgePvcTableA table of bridge-bridge PVC connection SEQUENCE OF BridgeBridgePvcEntry .1.3.6.1.4.1.1751.2.18.6.12 |
bridgeBridgePvcEntryRow definitions of bridge-bridge PVC
connection attributes BridgeBridgePvcEntry .1.3.6.1.4.1.1751.2.18.6.12.1 |
bridgeBridgePvcIfAInterface index for side A of a bridge-bridge
PVC connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. Integer32 .1.3.6.1.4.1.1751.2.18.6.12.1.1 |
bridgeBridgePvcIfBInterface index for side B of a bridge-bridge
PVC connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. Integer32 .1.3.6.1.4.1.1751.2.18.6.12.1.2 |
bridgeBridgePvcRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.12.1.3 |
bridgeBridgePvcConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.12.1.4 |
bridgeBridgePvcConnFailureCauseAconnestion status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.12.1.5 |
bridgeBridgePvcConnFailureCauseBconnection status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.12.1.6 |
bridgeAtmPvcVccTableTable of bridge Atm PVC VCC connection entries SEQUENCE OF BridgeAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.13 |
bridgeAtmPvcVccEntryRow definition of bridge atm PVC VCC connection
attribution. BridgeAtmPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.13.1 |
bridgeAtmPvcVccIfAInterface index for side A, the bridge side, of a
bridge-atm PVC VCC connection. Number value is
interpreted as an interface of the form, SSPPCCC,
where SS is the card slot, PP is the port number,
and CCC is the channel number. Integer32 .1.3.6.1.4.1.1751.2.18.6.13.1.1 |
bridgeAtmPvcVccIfBInterface index for side B, the atm side, of a
bridge-atm PVC VCC connection. Number value is
interpreted as an interface of the form, SSPPCCC,
where SS is the card slot, PP is the port number,
and CCC is the channel number. Integer32 .1.3.6.1.4.1.1751.2.18.6.13.1.2 |
bridgeAtmPvcVccVpiBVPI value for side B, the atm side, of a
bridge-atm PVC VCC connection. Valid range is a
number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.13.1.3 |
bridgeAtmPvcVccVciBVCI value for side B, the atm side, of a
bridge-atm PVC VCC connection. Valid range is a
number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.13.1.4 |
bridgeAtmPvcVccServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.13.1.5 |
bridgeAtmPvcVccPeakCellRateB2Apeak rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.13.1.6 |
bridgeAtmPvcVccSusCellRateB2Asustained rate - side B, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.13.1.7 |
bridgeAtmPvcVccMaxBurstSizeB2Amaximum burst size - side B, in cells.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.13.1.8 |
bridgeAtmPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.13.1.9 |
bridgeAtmPvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.13.1.10 |
bridgeAtmPvcVccDualHomedDoes this PVC need a backup Dual homing PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.13.1.11 |
bridgeAtmPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.13.1.12 |
bridgeAtmPvcVccCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the
the 0 or 0plus1 refers to the clp bit in the
cells. If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.13.1.14 |
bridgeAtmPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.13.1.15 |
bridgeAtmPvcVccMfsB2AMaximum Frame Size for GFR trafficrw INTEGER .1.3.6.1.4.1.1751.2.18.6.13.1.16 |
bridgeAtmPvcVccConnFailureCauseAconnestion status reason codero ConnFailureCause .1.3.6.1.4.1.1751.2.18.6.13.1.17 |
bridgeAtmPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.13.1.18 |
bridgeAtmPvcVccOamStatusIndicates the OAM monitoring status of side A.
The 3 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
End-Seg-Pt: A side is both an end point and a
segment point.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.13.1.19 |
bridgeAtmPvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.13.1.20 |
cirEmAtmBkPvcVccTableThis table is used to manage CES DHPVC backup pvc. SEQUENCE OF CirEmAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.14 |
cirEmAtmBkPvcVccEntryAn entry in the CES DHPVC table. There is one
entry in the table corresponding to each active
row in the cirEmAtmPvcVccTable for which the
cirEmAtmPvcVccDualHomed object takes the value
'yes.' CirEmAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.14.1 |
cirEmAtmBkPvcVccIfBInterface index for side B, the atm side, of a
backup circuit emulation-atm DHPVC VCC connection.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.6.14.1.1 |
cirEmAtmBkPvcVccVpiBVPI value for side B, the atm side, of a backup
circuit emulation-atm DHPVC VCC connection. Valid
range is a number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.14.1.2 |
cirEmAtmBkPvcVccVciBVCI value for side B, the atm side, of a backup
circuit emulation-atm DHPVC VCC connection. Valid
range is a number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.14.1.3 |
cirEmAtmBkPvcVccActivePvcCurrent active PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.14.1.4 |
cirEmAtmBkPvcVccAutoSwitchAuto switch back to primary link when primary link
is recovered.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.14.1.5 |
cirEmAtmBkPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.14.1.6 |
cirEmAtmBkPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.14.1.7 |
cirEmAtmBkPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.14.1.8 |
cirEmAtmBkPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.14.1.9 |
vbrAtmBkPvcVccTableThis table is used to manage terminal emulation
DHPVC backup pvc. SEQUENCE OF VbrAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.15 |
vbrAtmBkPvcVccEntryAn entry in the terminal emulation DHPVC table.
There is one entry in the table corresponding to
each active row in the vbrAtmPvcVccTable for which
the vbrAtmPvcVccDualHomed object takes the value
'yes'. VbrAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.15.1 |
vbrAtmBkPvcVccIfBInterface index for side B, the atm side, of a
backup terminal emulation-atm DHPVC VCC connection.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.6.15.1.1 |
vbrAtmBkPvcVccVpiBVPI value for side B, the atm side, of a backup
terminal emulation-atm DHPVC VCC connection.
Valid range is a number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.15.1.2 |
vbrAtmBkPvcVccVciBVCI value for side B, the atm side, of a backup
terminal emulation-atm DHPVC VCC connection.
Valid range is a number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.15.1.3 |
vbrAtmBkPvcVccActivePvcCurrent active PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.15.1.4 |
vbrAtmBkPvcVccAutoSwitchAuto switch back to primary link when primary link
is recovered.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.15.1.5 |
vbrAtmBkPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.15.1.6 |
vbrAtmBkPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.15.1.7 |
vbrAtmBkPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.15.1.8 |
vbrAtmBkPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.15.1.9 |
atmSpvcVccAddrTableTable of SPVC ATM network interface addresses. SEQUENCE OF AtmSpvcVccAddrEntry .1.3.6.1.4.1.1751.2.18.6.16 |
atmSpvcVccAddrEntryRow definition of ATM SPVC address table. AtmSpvcVccAddrEntry .1.3.6.1.4.1.1751.2.18.6.16.1 |
atmSpvcVccIfAInterface index for side A of an ATM SPVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.16.1.1 |
atmSpvcVccAtmPortAddrLocal ATM port NSAP address.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.16.1.2 |
atmSpvcVccAddrRowStatusThis is used to configure a NSAP address on the
local port. Only when the address is configured
can SPVC connections be established.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.16.1.3 |
atmSpvcVccTableTable of SPVC ATM virtual channel connections. SEQUENCE OF AtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.17 |
atmSpvcVccEntryRow definition of ATM SPVC VCC connections. AtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.17.1 |
atmSpvcVccVpiAVPI value for side A of an ATM SPVC VCC connection.
Valid range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.17.1.1 |
atmSpvcVccVciAVCI value for side A of an ATM SPVC VCC connection.
Valid range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.17.1.2 |
atmSpvcVccIfBInterface index for side B of an ATM SPVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.17.1.3 |
atmSpvcVccVpiBVPI value for side B of an ATM SPVC VCC connection.
Valid range is a number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.17.1.4 |
atmSpvcVccVciBVCI value for side B of an ATM SPVC VCC connection.
Valid range is a number between 0 and 65535.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.17.1.5 |
atmSpvcVccServiceTypeA2BService type, ATM port.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.6 |
atmSpvcVccSarTypeA2BSAR type used in ATM adaption, ATM port.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.7 |
atmSpvcVccPeakCellRateA2BPeak cell rate - side A, ATM port, in cells per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.17.1.8 |
atmSpvcVccSusCellRateA2BSustained cell rate - side A, ATM port, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.17.1.9 |
atmSpvcVccMaxBurstSizeA2BMaximum burst size - side A, ATM port, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.17.1.10 |
atmSpvcVccFrwdErrCorrectionA2BForward error correction scheme, ATM port side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.11 |
atmSpvcVccServiceTypeB2AService type, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.12 |
atmSpvcVccSarTypeB2ASAR type used in ATM adaption, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.13 |
atmSpvcVccPeakCellRateB2APeak cell rate - side B, ATM trunk, in cells per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.17.1.14 |
atmSpvcVccSusCellRateB2ASustained cell rate - side B, ATM trunk, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.17.1.15 |
atmSpvcVccMaxBurstSizeB2AMaximum burst size - side A, ATM trunk, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.17.1.16 |
atmSpvcVccFrwdErrCorrectionB2AForward error correction scheme, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.17 |
atmSpvcVccFlowType of flow, pointToMultipointA2B is for future
support.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.18 |
atmSpvcVccTypeType of connection.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.19 |
atmSpvcVccConnTypeThe type of connection:
activeSvc - attempt calls, whenever not
established.
passiveSvc - accept calls.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.20 |
atmSpvcVccLeafReferenceAn arbitrary integer which serves to distinguish
the mulitple leaves attached to a root of a
point-to-multipoint SPVC. If point-to-point SPVC,
the value should be 1.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.17.1.21 |
atmSpvcVccOperStatusThe operation status of the connection:
other - none of the types specified below.
establishmentInProgress - connection is not
operational, but call attempts are ongoing.
connected - connection is currently operational.
retriesExhausted - retry limit has been reached
and call attempts have ceased.
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated.
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.22 |
atmSpvcVccRowStatusUsed to create and delete a soft PVC. When this
object is set to 'active', an attempt is made to
set up the soft PVC. When this object has the
value 'active' and is set to another value, any
setup or connection in-progress is released.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.17.1.23 |
atmSpvcVccViAVI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.17.1.24 |
atmSpvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.17.1.25 |
atmSpvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.26 |
atmSpvcVccTrafficShapingB2ATraffic Shaping Support in the B2A direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.17.1.27 |
atmSpvcVccActiveSvcTableThe table used to manage active SVCs established
across ATM networks between ATM entities. SEQUENCE OF AtmSpvcVccActiveSvcEntry .1.3.6.1.4.1.1751.2.18.6.18 |
atmSpvcVccActiveSvcEntryAn entry in the ATM active SVC table. There is one
entry in the table corresponding to each active row
in the atm SPVC VCC Table for which the
atmSpvcVccConnType takes the value 'activeSvc'. AtmSpvcVccActiveSvcEntry .1.3.6.1.4.1.1751.2.18.6.18.1 |
atmSpvcVccRemoteAtmPortAddrRemote ATM port NSAP address, not meaningful if
passive type of connection.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.18.1.1 |
atmSpvcVccRemoteSelectTypeIndicates whether the remote VPI/VCI values are to
be used at the destination. If 'any' is used, the
destination switch will choose the VPI/VCI values.
In such a case, once the SPVC is connected, the
value of this object will change to 'required',
such that the same VPI/VCI values will continue to
be used even if the connection is torn down and
re-established. If the value 'required' is
specified, the values: atmSpvcVccRemoteVpi and
atmSpvcVccRemoteVci, must be supplied and are used
at the destination.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.18.1.2 |
atmSpvcVccRemoteVpiVPI value to be used at the destination of an
ATM SPVC VCC connection. Valid range is a number
between 0 and 4095. If atmSpvcVccRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.18.1.3 |
atmSpvcVccRemoteVciVCI value to be used at the destination of an ATM
SPVC VCC connection. Valid range is a number
between 0 and 65535. If atmSpvcVccRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.18.1.4 |
atmSpvcVccRetryIntervalThe time to wait before attempting to establish
the SVC after a previous failed call attempt. A
value of 0 indicates retry will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.18.1.5 |
atmSpvcVccRetryLimitA maximum limit on how many retries should be
attempted. A value of 0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.18.1.6 |
atmSpvcVccRestartThe active SVC is released, if necessary, and a
new setup procedure is begun if 'restart',
otherwise, noop.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.18.1.7 |
atmSpvcVccRetryFailureIndicates how many attempts to establish the
connection have failed. It it reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.18.1.8 |
atmSpvcVccReleaseCauseCAUSE field value of the last RELEASE message
received for this SVC.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.18.1.9 |
atmSpvcVccReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVC.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.18.1.10 |
cirEmAtmSpvcVccTableTable of Circuit Emulation to ATM Soft PVCs. SEQUENCE OF CirEmAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.19 |
cirEmAtmSpvcVccEntryRow definition of circuit emulation to ATM SPVC
connections. CirEmAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.19.1 |
cirEmAtmSpvcVccIfAInterface index for side A, the circuit emulation
side, of a circuit emulation-atm SPVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.19.1.1 |
cirEmAtmSpvcVccIfBInterface index for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.19.1.2 |
cirEmAtmSpvcVccVpiBVPI value for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Valid
range is a number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.19.1.3 |
cirEmAtmSpvcVccVciBVCI value for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Valid
range is a number between 0 and 65535.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.19.1.4 |
cirEmAtmSpvcVccVoiceCompressionA2BVoice Compression Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.5 |
cirEmAtmSpvcVccSilenceDetectionA2Bsilence detection off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.6 |
cirEmAtmSpvcVccEchoCancellationA2BEcho Cancellation Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.7 |
cirEmAtmSpvcVccCngToneDetectionA2BCalling Tone Detection Algorithm,
one of the enum value, g726-32k(3)
is obsoleted on 01Mar99 such that
user would not be able to configure
CE-ATMrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.8 |
cirEmAtmSpvcVccCodingTranslationA2BCoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.9 |
cirEmAtmSpvcVccVoiceCompressionB2AVoice Compression Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.10 |
cirEmAtmSpvcVccSilenceDetectionB2Asilence detection off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.11 |
cirEmAtmSpvcVccEchoCancellationB2AEcho Cancellation Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.12 |
cirEmAtmSpvcVccCngToneDetectionB2ACalling Tone Detection Algorithm,
one of the enum value, g726-32k(3)
is obsoleted on 01Mar99 such that
user would not be able to configure
CE-ATMrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.13 |
cirEmAtmSpvcVccCodingTranslationB2ACoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.14 |
cirEmAtmSpvcVccFlowFlow Type, pointToMultipointA2B and
pointToMultipointB2A are for future support.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.15 |
cirEmAtmSpvcVccServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.16 |
cirEmAtmSpvcVccConnTypeThe type of connection: activeSvc - attempt calls,
whenever not established;
passiveSvc - accepts callsrw Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.17 |
cirEmAtmSpvcVccCePortAddrlocal CES port nsap addressrw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.19.1.18 |
cirEmAtmSpvcVccOperStatusother - none of the types specified below;
establishmentInProgress - connection is not
operational, but call attempts are ongoing;
connected - connection is currently operational;
retriesExhausted - retry limit has been reached
and call attempts have ceased;
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated;
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.19.1.19 |
cirEmAtmSpvcVccRowStatusUsed to create and delete a soft PVCC. When this
object is set to 'active' an attempt is made to
set up the soft PVCC. When this object has the
value 'active' and is set to another value, any
set-up or connection in-progess is released.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.19.1.20 |
cirEmAtmSpvcVccViBVI to associate the Egress part of
the B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.19.1.21 |
cirEmAtmSpvcVccActiveSvcTableThe table used to manage active SVCs established
across ATM networks between CES entities. SEQUENCE OF CirEmAtmSpvcVccActiveSvcEntry .1.3.6.1.4.1.1751.2.18.6.20 |
cirEmAtmSpvcVccActiveSvcEntryAn entry in the CES active SVC table. There is
one entry in the table corresponding to each
active row in the cirEmAtmSpvcVccRowStatus for
which the cirEmAtmSpvcVccConnType takes the value
'activeSvc'. CirEmAtmSpvcVccActiveSvcEntry .1.3.6.1.4.1.1751.2.18.6.20.1 |
cirEmAtmSpvcVccRemoteCePortAddrThe ATM address supporting the corresponding far
end CES IWF process. If no address is supplied,
no attempts to establish the active SVC are
initiated.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.20.1.1 |
cirEmAtmSpvcVccRetryIntervalThe time to wait before attempting to establish
the SVC after previous failed call attempt.
0 indicates retry will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.20.1.2 |
cirEmAtmSpvcVccRetryLimitA maximum limit on how many retries.
0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.20.1.3 |
cirEmAtmSpvcVccRestartrestart, the active SVC is released if necessary
and a new setup procedure is begun; or nooprw Enumeration .1.3.6.1.4.1.1751.2.18.6.20.1.4 |
cirEmAtmSpvcVccRetryFailureIndicates how many attempts to establish the
connection have failed. It is reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.20.1.5 |
cirEmAtmSpvcVccReleaseCauseCAUSE field value of the last RELEASE message
received for this SVC.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.20.1.6 |
cirEmAtmSpvcVccReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVC.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.20.1.7 |
vbrAtmSpvcVccTableTable of SPVC atm virtual channel connections SEQUENCE OF VbrAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.21 |
vbrAtmSpvcVccEntryRow definition of atm SPVC VCC connections VbrAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.21.1 |
vbrAtmSpvcVccIfAInterface index for side A, the variable bit rate
side, of a variable bit rate-atm SPVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.21.1.1 |
vbrAtmSpvcVccIfBInterface index for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.21.1.2 |
vbrAtmSpvcVccVpiBVPI value for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Valid
range is a number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.21.1.3 |
vbrAtmSpvcVccVciBVCI value for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Valid
range is a number between 0 and 65535.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.21.1.4 |
vbrAtmSpvcVccServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.21.1.5 |
vbrAtmSpvcVccPeakCellRateA2Bpeak cell rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.21.1.6 |
vbrAtmSpvcVccSusCellRateA2Bsustained rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.21.1.7 |
vbrAtmSpvcVccMaxBurstSizeA2Bmaximum burst size - side A, in cellsrw Integer32 .1.3.6.1.4.1.1751.2.18.6.21.1.8 |
vbrAtmSpvcVccPeakCellRateB2Apeak rate - side B, ATM trunk, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.21.1.9 |
vbrAtmSpvcVccSusCellRateB2Asustained rate - side B, ATM trunk, in cell per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.21.1.10 |
vbrAtmSpvcVccMaxBurstSizeB2Amaximum burst size - side B, ATM trunk, in cells.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.21.1.11 |
vbrAtmSpvcVccFlowtype of flowrw Enumeration .1.3.6.1.4.1.1751.2.18.6.21.1.12 |
vbrAtmSpvcVccConnTypeThe type of connection: activeSvc - attempt calls,
whenever not established;
passiveSvc - accepts callsrw Enumeration .1.3.6.1.4.1.1751.2.18.6.21.1.13 |
vbrAtmSpvcVccVbrPortAddrlocal Vbr port nsap addressrw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.21.1.14 |
vbrAtmSpvcVccOperStatusother - none of the types specified below;
establishmentInProgress - connection is not
operational, but call attempts are ongoing;
connected - connection is currently operational;
retriesExhausted - retry limit has been reached
and call attempts have ceased;
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated;
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.21.1.15 |
vbrAtmSpvcVccRowStatusUsed to create and delete a soft PVCC. When this
object is set to 'active' an attempt is made to
set up the soft PVCC. When this object has the
value 'active' and is set to another value, any
set-up or connection in-progess is released.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.21.1.16 |
vbrAtmSpvcVccViBVI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.21.1.17 |
vbrAtmSpvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.21.1.18 |
vbrAtmSpvcVccActiveSvcTableThe table used to manage active SVCs established
across ATM networks between ATM entities. SEQUENCE OF VbrAtmSpvcVccActiveSvcEntry .1.3.6.1.4.1.1751.2.18.6.22 |
vbrAtmSpvcVccActiveSvcEntryAn entry in the Terminal Emulation ATM active SVC
table. There is one entry in the table
corresponding to each active row in the
vbrAtmSpvcVccTable for which the
vbrAtmSpvcVccConnType
takes the value 'activeSvc'. VbrAtmSpvcVccActiveSvcEntry .1.3.6.1.4.1.1751.2.18.6.22.1 |
vbrAtmSpvcVccRemoteVbrPortAddrremote VBR port nsap address implemening IWF, not
meaningful if passive type of connectionrw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.22.1.1 |
vbrAtmSpvcVccRetryIntervalthe time to wait before attempting to establish
the SVC after previous failed call attempt.
0 indicates retry will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.22.1.2 |
vbrAtmSpvcVccRetryLimita maximum limit on how many retries.
0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.22.1.3 |
vbrAtmSpvcVccRestartrestart, the active SVC is released if necessary
and a new setup procedure is begun; or nooprw Enumeration .1.3.6.1.4.1.1751.2.18.6.22.1.4 |
vbrAtmSpvcVccRetryFailureindicates how many attempts to establish the
connection have failed. It is reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.22.1.5 |
vbrAtmSpvcVccReleaseCauseCAUSE field value of the last RELEASE message
received for this SVCro INTEGER .1.3.6.1.4.1.1751.2.18.6.22.1.6 |
vbrAtmSpvcVccReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVCro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.22.1.7 |
atmSpvcVccRlsTableThis table is an extension of atmSpvcVccTable
and is used to release a ATM-ATM SPVC connection
without deleting the configured data. SEQUENCE OF AtmSpvcVccRlsEntry .1.3.6.1.4.1.1751.2.18.6.23 |
atmSpvcVccRlsEntryRow definition of CES SPVC release table. This
entry is created whenever an entry is created in
atmSpvcVccTable. AtmSpvcVccRlsEntry .1.3.6.1.4.1.1751.2.18.6.23.1 |
atmSpvcVccReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.23.1.1 |
cirEmAtmSpvcVccRlsTableThis table is an extension of cirEmAtmSpvcVccTable
and is used to release a TE-ATM SPVC connection
without deleting the configured data. SEQUENCE OF CirEmAtmSpvcVccRlsEntry .1.3.6.1.4.1.1751.2.18.6.24 |
cirEmAtmSpvcVccRlsEntryRow definition of CES SPVC release table. This
entry is created whenever an entry is created in
cirEmAtmSpvcVccTable. CirEmAtmSpvcVccRlsEntry .1.3.6.1.4.1.1751.2.18.6.24.1 |
cirEmAtmSpvcVccReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.24.1.1 |
vbrAtmSpvcVccRlsTableThis table is an extension of vbrAtmSpvcVccTable
and is used to release a TE-ATM SPVC connection
without deleting the configured data. SEQUENCE OF VbrAtmSpvcVccRlsEntry .1.3.6.1.4.1.1751.2.18.6.25 |
vbrAtmSpvcVccRlsEntryRow definition of TE SPVC release table. This
entry is created whenever an entry is created in
vbrAtmSpvcVccTable. VbrAtmSpvcVccRlsEntry .1.3.6.1.4.1.1751.2.18.6.25.1 |
vbrAtmSpvcVccReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.25.1.1 |
frAtmBkPvcVccTableThis table is used to manage frame relay DHPVC
backup pvc. SEQUENCE OF FrAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.26 |
frAtmBkPvcVccEntryAn entry in the frame relay DHPVC table. There is
one entry in the table corresponding to each active
row in the frAtmPvcVccTable for which the
frAtmPvcVccDualHomed object takes the value
'yes.' FrAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.26.1 |
frAtmBkPvcVccIfBInterface index for side B, the atm side, of a
backup frame relay-atm DHPVC VCC connection.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.6.26.1.1 |
frAtmBkPvcVccVpiBVPI value for side B, the atm side, of a backup
frame relay-atm DHPVC VCC connection. Valid
range is a number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.26.1.2 |
frAtmBkPvcVccVciBVCI value for side B, the atm side, of a backup
frame relay-atm DHPVC VCC connection. Valid
range is a number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.26.1.3 |
frAtmBkPvcVccActivePvcCurrent active PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.26.1.4 |
frAtmBkPvcVccAutoSwitchAuto switch back to primary link when primary link
is recovered.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.26.1.5 |
frAtmBkPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.26.1.6 |
frAtmBkPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.26.1.7 |
frAtmBkPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.26.1.8 |
frAtmBkPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.26.1.9 |
atmBkPvcVccTableThis table is used to manage ATM to ATM
DHPVC backup pvc. SEQUENCE OF AtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.27 |
atmBkPvcVccEntryAn entry in the ATM to ATM DHPVC table.
There is one entry in the table corresponding to
each active row in the atmPvcVccTable for which
the atmPvcVccDualHomed object takes the value
'yes'. AtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.27.1 |
atmBkPvcVccIfBInterface index for side B, the atm side, of a
backup ATM-to-ATM DHPVC VCC connection.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.6.27.1.1 |
atmBkPvcVccVpiBVPI value for side B, the atm side, of a backup
ATM-to-ATM DHPVC VCC connection.
Valid range is a number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.27.1.2 |
atmBkPvcVccVciBVCI value for side B, the atm side, of a backup
ATM-to-ATM DHPVC VCC connection.
Valid range is a number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.27.1.3 |
atmBkPvcVccActivePvcCurrent active PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.27.1.4 |
atmBkPvcVccAutoSwitchAuto switch back to primary link when primary link
is recovered.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.27.1.5 |
atmBkPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.27.1.6 |
atmBkPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.27.1.7 |
atmBkPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.27.1.8 |
atmBkPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.27.1.9 |
atmBkPvcVpcTableThis table is used to manage ATM to ATM DHPVC
backup pvc. SEQUENCE OF AtmBkPvcVpcEntry .1.3.6.1.4.1.1751.2.18.6.28 |
atmBkPvcVpcEntryAn entry in the ATM to ATM DHPVC table. There is
one entry in the table corresponding to each
active row in the atmPvcVpcTable for which the
atmPvcVpcDualHomed object takes the value 'yes'. AtmBkPvcVpcEntry .1.3.6.1.4.1.1751.2.18.6.28.1 |
atmBkPvcVpcIfBInterface index for side B of an ATM-to-ATM PVC VPC
backup DHPVC connection. Number value is
interpreted as an interface of the form, SSPPCCC,
where SS is the card slot, PP is the port number,
and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.6.28.1.1 |
atmBkPvcVpcVpiBVPI value for side B of an ATM-to-ATM PVC VPC backup
DHPVC connection. Valid range is a number between
0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.28.1.2 |
atmBkPvcVpcActivePvcCurrent active PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.28.1.3 |
atmBkPvcVpcAutoSwitchAuto switch back to primary link when primary link
is recovered.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.28.1.4 |
atmBkPvcVpcRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.28.1.5 |
atmBkPvcVpcViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.28.1.6 |
atmBkPvcVpcVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.28.1.7 |
atmBkPvcVpcConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.28.1.8 |
bridgeAtmBkPvcVccTableThis table is used to manage bridge to atm DHPVC
backup pvc. SEQUENCE OF BridgeAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.29 |
bridgeAtmBkPvcVccEntryAn entry in the bridge to atm DHPVC table. There
is one entry in the table corresponding to each
active row in the bridgeAtmPvcVccTable for which
the bridgeAtmPvcVccDualHomed object takes the
value 'yes'. BridgeAtmBkPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.29.1 |
bridgeAtmBkPvcVccIfBInterface index for side B, the atm side, of a
backup bridge-atm DHPVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.6.29.1.1 |
bridgeAtmBkPvcVccVpiBVPI value for side B, the atm side, of a backup
bridge-atm DHPVC VCC connection. Valid range is a
number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.29.1.2 |
bridgeAtmBkPvcVccVciBVCI value for side B, the atm side, of a backup
bridge-atm DHPVC VCC connection. Valid range is a
number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.29.1.3 |
bridgeAtmBkPvcVccActivePvcCurrent active PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.29.1.4 |
bridgeAtmBkPvcVccAutoSwitchAuto switch back to primary link when primary link
is recovered.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.29.1.5 |
bridgeAtmBkPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.29.1.6 |
bridgeAtmBkPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.29.1.7 |
bridgeAtmBkPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.29.1.8 |
bridgeAtmBkPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.29.1.9 |
ipAtmBkAppPvcVccTableThis table is used to manage in-band management to
atm DHPVC backup pvc. SEQUENCE OF IpAtmBkAppPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.30 |
ipAtmBkAppPvcVccEntryAn entry in the in-band management to atm DHPVC
table. There is one entry in the table
corresponding to each active row in the
ipAtmAppPvcVccTable for which the
ipAtmAppPvcVccDualHomed object takes the value
'yes'. IpAtmBkAppPvcVccEntry .1.3.6.1.4.1.1751.2.18.6.30.1 |
ipAtmBkAppPvcVccIfBInterface index for side B, the atm side, of a
backup in-band management-atm DHPVC VCC connection.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.6.30.1.1 |
ipAtmBkAppPvcVccVpiBVPI value for side B, the atm side, of a backup
in-band management-atm DHPVC VCC connection. Valid
range is a number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.30.1.2 |
ipAtmBkAppPvcVccVciBVCI value for side B, the atm side, of a backup
in-band management-atm DHPVC VCC connection. Valid
range is a number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.30.1.3 |
ipAtmBkAppPvcVccActivePvcCurrent active PVC.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.30.1.4 |
ipAtmBkAppPvcVccAutoSwitchAuto switch back to primary link when primary link
is recovered.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.30.1.5 |
ipAtmBkAppPvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.30.1.6 |
ipAtmBkAppPvcVccViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.30.1.7 |
ipAtmBkAppPvcVccVUNIBVUNI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.30.1.8 |
ipAtmBkAppPvcVccConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.30.1.9 |
spvcAddrTableTable of SPVC network interface addresses. SEQUENCE OF SpvcAddrEntry .1.3.6.1.4.1.1751.2.18.6.31 |
spvcAddrEntryRow definition of SPVC address table. SpvcAddrEntry .1.3.6.1.4.1.1751.2.18.6.31.1 |
spvcAddrIfAInterface index for side A of an SPVC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.31.1.1 |
spvcAddrLocalPortAddrLocal port NSAP address.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.31.1.2 |
spvcAddrRowStatusThis is used to configure a NSAP address on the
local port. Only when the address is configured
can SPVC connections be established.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.31.1.3 |
frAtmSpvcVccTableTable of frame relay to ATM IWF connections SEQUENCE OF FrAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.32 |
frAtmSpvcVccEntryRow definition of frame relay to ATM IWF
connections FrAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.32.1 |
frAtmSpvcVccDlciADLCI value for side A, the frame relay side,
of a frame relay-atm SPVC VCC connection. Valid
range is a number between 0 and 1023. INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.1 |
frAtmSpvcVccIfBInterface index for side B, the atm side, of a
frame relay-atm SPVC VCC connection. Number value
is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.32.1.2 |
frAtmSpvcVccVpiBVPI value for side B, the atm side, of a frame
relay-atm SPVC VCC connection. Valid range is a
number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.3 |
frAtmSpvcVccVciBVCI value for side B, the atm side, of a frame
relay-atm SPVC VCC connection. Valid range is a
number between 0 and 65535.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.4 |
frAtmSpvcVccMaxFrameSizeInThe value of this object is the size in octets of
the largest frame relay information field for this
SPVC in the ingress direction (out of the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.5 |
frAtmSpvcVccBcInThe value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this SPVC in the ingress
direction (into the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.6 |
frAtmSpvcVccBeInThe value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this SPVC in the ingress direction (into
the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.7 |
frAtmSpvcVccCirInThe value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this SPVC
in the ingress direction (into the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.8 |
frAtmSpvcVccMaxFrameSizeOutThe value of this object is the size in octets of
the largest frame relay information field for this
SPVC in the egress direction (out of the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.9 |
frAtmSpvcVccBcOutThe value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this SPVC in the egress
direction (into the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.10 |
frAtmSpvcVccBeOutThe value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this SPVC in the egress direction (into
the frame relay UNI)rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.11 |
frAtmSpvcVccCirOutThe value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this SPVC
in the egress direction (into the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.12 |
frAtmSpvcVccServiceTypeservice type, Frame relay traffic is carried
by VBR type of service only.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.13 |
frAtmSpvcVccFlowFlow Typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.14 |
frAtmSpvcVccTimeLenInThe time interval over which CIR and the burst
sizes (Bc and Be) are measured in the A2B
direction. The unit is milliseconds.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.15 |
frAtmSpvcVccTimeLenOutThe time interval over which CIR and the burst
sizes (Bc and Be) are measured in the A2B
direction. The unit is milliseconds.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.16 |
frAtmSpvcVccPeakCellRateA2BPeak cell rate - side A, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.17 |
frAtmSpvcVccSusCellRateA2BSustained cell rate - side A, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.18 |
frAtmSpvcVccMaxBurstSizeA2BMaximum burst size - side A, in cells,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.19 |
frAtmSpvcVccPeakCellRateB2APeak cell rate - side B, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.20 |
frAtmSpvcVccSusCellRateB2ASustained cell rate - side B, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.21 |
frAtmSpvcVccMaxBurstSizeB2AMaximum burst size - side B, in cells,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.22 |
frAtmSpvcVccInterWorkingFuncInterWorking function.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.23 |
frAtmSpvcVccConnTypeThe type of connection: activeSvc - attempt calls,
whenever not established; passiveSvc - accepts callsrw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.24 |
frAtmSpvcVccOperStatusother - none of the types specified below;
establishmentInProgress - connection is not
operational, but call attempts are ongoing;
connected - connection is currently operational;
retriesExhausted - retry limit has been reached
and call attempts have ceased;
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated;
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.25 |
frAtmSpvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.32.1.26 |
frAtmSpvcVccRemoteFrPortAddrThe ATM address supporting the corresponding far
end FR IWF process. If no address is supplied,
no attempts to establish the active SVC are
initiated.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.6.32.1.27 |
frAtmSpvcVccRemoteSelectTypeIndicates whether the remote DLCI/VPI/VCI values are to
be used at the destination. If 'any' is used, the
destination switch will choose the DLCI/VPI/VCI values.
In such a case, once the SPVC is connected, the
value of this object will change to 'required',
such that the same DLCI/VPI/VCI values will continue to
be used even if the connection is torn down and
re-established. If the value 'required' is
specified, the values: frAtmSpvcVccRemoteDlci or
frAtmSpvcVccRemoteVpi and frAtmSpvcVccRemoteVci, must
be supplied and are used at the destination.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.28 |
frAtmSpvcVccRemoteDlciDLCI value to be used at the destination of an
ATM SPVC VCC connection. Valid range is a number
between 0 and 4095. If frAtmSpvcVccRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.29 |
frAtmSpvcVccRemoteVpiVPI value to be used at the destination of an
ATM SPVC VCC connection. Valid range is a number
between 0 and 4095. If frAtmSpvcVccRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.30 |
frAtmSpvcVccRemoteVciVCI value to be used at the destination of an ATM
SPVC VCC connection. Valid range is a number
between 0 and 65535. If frAtmSpvcVccRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.31 |
frAtmSpvcVccRetryIntervalThe time to wait before attempting to establish
the SVC after previous failed call attempt.
0 indicates retry will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.32 |
frAtmSpvcVccRetryLimitA maximum limit on how many retries.
0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.33 |
frAtmSpvcVccRestartrestart, the active SVC is released if necessary
and a new setup procedure is begun; or nooprw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.34 |
frAtmSpvcVccRetryFailureIndicates how many attempts to establish the
connection have failed. It is reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.35 |
frAtmSpvcVccReleaseCauseCAUSE field value of the last RELEASE message
received for this SVC.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.36 |
frAtmSpvcVccReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVC.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.32.1.37 |
frAtmSpvcVccReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.38 |
frAtmSpvcVccStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.39 |
frAtmSpvcVccStatsCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.40 |
frAtmSpvcVccStatsCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.41 |
frAtmSpvcVccStatsCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.42 |
frAtmSpvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.43 |
frAtmSpvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.44 |
frAtmSpvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.45 |
frAtmSpvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.46 |
frAtmSpvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.47 |
frAtmSpvcVccStatsFramesDroppedANumber of frames dropped for a given DLCI for A2B
direction, only applicable to the input side.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.48 |
frAtmSpvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.49 |
frAtmSpvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.50 |
frAtmSpvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.51 |
frAtmSpvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.52 |
frAtmSpvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.53 |
frAtmSpvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.54 |
frAtmSpvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.55 |
frAtmSpvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.56 |
frAtmSpvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.57 |
frAtmSpvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.58 |
frAtmSpvcVccStatsAal5ErrFramesANumber of Aal5 Errored Frames, which are not
dropped due to UPC in A2B dir,
only applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.59 |
frAtmSpvcVccStatsFramesTaggedANumber of Frames tagged due to UPC in A2B
dir, only applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.60 |
frAtmSpvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.61 |
frAtmSpvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.32.1.62 |
frAtmSpvcVccVUNIBVUNI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.32.1.63 |
frAtmSpvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.64 |
frAtmSpvcVccPriorityPriority of SPVC - priority-1 being highest priority .rw Enumeration .1.3.6.1.4.1.1751.2.18.6.32.1.65 |
atmAtmSpvcVccTableTable of SPVC ATM virtual channel connections. SEQUENCE OF AtmAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.33 |
atmAtmSpvcVccEntryRow definition of ATM SPVC VCC connections. AtmAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.33.1 |
atmAtmSpvcVccVpiAVPI value for side A of an ATM SPVC VCC connection.
Valid range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.1 |
atmAtmSpvcVccVciAVCI value for side A of an ATM SPVC VCC connection.
Valid range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.2 |
atmAtmSpvcVccRemoteAtmPortAddrRemote ATM port NSAP address, not meaningful if
passive type of connection. OCTET STRING .1.3.6.1.4.1.1751.2.18.6.33.1.3 |
atmAtmSpvcVccIfBInterface index for side B of an ATM SPVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.33.1.4 |
atmAtmSpvcVccVpiBVPI value for side B of an ATM SPVC VCC connection.
Valid range is a number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.5 |
atmAtmSpvcVccVciBVCI value for side B of an ATM SPVC VCC connection.
Valid range is a number between 0 and 65535.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.6 |
atmAtmSpvcVccServiceTypeA2BService type, ATM port.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.7 |
atmAtmSpvcVccSarTypeA2BSAR type used in ATM adaption, ATM port.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.8 |
atmAtmSpvcVccPeakCellRateA2BPeak cell rate - side A, ATM port, in cells per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.9 |
atmAtmSpvcVccSusCellRateA2BSustained cell rate - side A, ATM port, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.10 |
atmAtmSpvcVccMaxBurstSizeA2BMaximum burst size - side A, ATM port, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.11 |
atmAtmSpvcVccFrwdErrCorrectionA2BForward error correction scheme, ATM port side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.12 |
atmAtmSpvcVccServiceTypeB2AService type, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.13 |
atmAtmSpvcVccSarTypeB2ASAR type used in ATM adaption, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.14 |
atmAtmSpvcVccPeakCellRateB2APeak cell rate - side B, ATM trunk, in cells per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.15 |
atmAtmSpvcVccSusCellRateB2ASustained cell rate - side B, ATM trunk, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.16 |
atmAtmSpvcVccMaxBurstSizeB2AMaximum burst size - side A, ATM trunk, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.17 |
atmAtmSpvcVccFrwdErrCorrectionB2AForward error correction scheme, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.18 |
atmAtmSpvcVccFlowType of flow, pointToMultipointA2B is for future
support.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.19 |
atmAtmSpvcVccTypeType of connection.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.20 |
atmAtmSpvcVccConnTypeThe type of connection:
activeSvc - attempt calls, whenever not
established.
passiveSvc - accept calls.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.21 |
atmAtmSpvcVccLeafReferenceAn arbitrary integer which serves to distinguish
the mulitple leaves attached to a root of a
point-to-multipoint SPVC. If point-to-point SPVC,
the value should be 1.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.22 |
atmAtmSpvcVccOperStatusThe operation status of the connection:
other - none of the types specified below.
establishmentInProgress - connection is not
operational, but call attempts are ongoing.
connected - connection is currently operational.
retriesExhausted - retry limit has been reached
and call attempts have ceased.
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated.
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.23 |
atmAtmSpvcVccRowStatusUsed to create and delete a soft PVC. When this
object is set to 'active', an attempt is made to
set up the soft PVC. When this object has the
value 'active' and is set to another value, any
setup or connection in-progress is released.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.33.1.24 |
atmAtmSpvcVccRemoteSelectTypeIndicates whether the remote VPI/VCI values are to
be used at the destination. If 'any' is used, the
destination switch will choose the VPI/VCI values.
In such a case, once the SPVC is connected, the
value of this object will change to 'required',
such that the same VPI/VCI values will continue to
be used even if the connection is torn down and
re-established. If the value 'required' is
specified, the values: atmAtmSpvcVccRemoteVpi and
atmAtmSpvcVccRemoteVci, must be supplied and are used
at the destination.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.25 |
atmAtmSpvcVccRemoteVpiVPI value to be used at the destination of an
ATM SPVC VCC connection. Valid range is a number
between 0 and 4095. If atmAtmSpvcVccRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.26 |
atmAtmSpvcVccRemoteVciVCI value to be used at the destination of an ATM
SPVC VCC connection. Valid range is a number
between 0 and 65535. If atmAtmSpvcVccRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.27 |
atmAtmSpvcVccRetryIntervalThe time to wait before attempting to establish
the SVC after a previous failed call attempt. A
value of 0 indicates retries will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.28 |
atmAtmSpvcVccRetryLimitA maximum limit on how many retries should be
attempted. A value of 0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.29 |
atmAtmSpvcVccRestartThe active SVC is released, if necessary, and a
new setup procedure is begun if 'restart',
otherwise, noop.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.30 |
atmAtmSpvcVccRetryFailureIndicates how many attempts to establish the
connection have failed. It it reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.31 |
atmAtmSpvcVccReleaseCauseCAUSE field value of the last RELEASE message
received for this SVC.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.32 |
atmAtmSpvcVccReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVC.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.33.1.33 |
atmAtmSpvcVccReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.34 |
atmAtmSpvcVccStatsInCellCountHiAValid Cells received on A - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.35 |
atmAtmSpvcVccStatsInCellCountLoAValid Cells received on A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.36 |
atmAtmSpvcVccStatsOutCellCountHiAValid cells transmitted on A -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.37 |
atmAtmSpvcVccStatsOutCellCountLoAValid cells transmitted on A -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.38 |
atmAtmSpvcVccStatsInCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.39 |
atmAtmSpvcVccStatsInCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.40 |
atmAtmSpvcVccStatsOutCellCountHiBValid cells transmitted on B -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.41 |
atmAtmSpvcVccStatsOutCellCountLoBValid cells transmitted on B -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.42 |
atmAtmSpvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.43 |
atmAtmSpvcVccStatsFrwdErrCrrctnRateA2BDisplays the Forward error correction rate being
used by the FEC module in the A2B direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.44 |
atmAtmSpvcVccStatsFrwdErrCrrctnRateB2ADisplays the Forward error correction rate being
used by the FEC module in the B2A direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.45 |
atmAtmSpvcVccStatsInOdometerCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.46 |
atmAtmSpvcVccStatsInOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.47 |
atmAtmSpvcVccStatsOutOdometerCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.48 |
atmAtmSpvcVccStatsOutOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.49 |
atmAtmSpvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.50 |
atmAtmSpvcVccStatsInOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.51 |
atmAtmSpvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.52 |
atmAtmSpvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.53 |
atmAtmSpvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.54 |
atmAtmSpvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.55 |
atmAtmSpvcVccViAVI to associate the Egress part of the B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.56 |
atmAtmSpvcVccViBVI to associate the Egress part of the A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.57 |
atmAtmSpvcVccStatsCellsDroppedACells Dropped on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.58 |
atmAtmSpvcVccStatsCellsTaggedACells Tagged on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.59 |
atmAtmSpvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.60 |
atmAtmSpvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.33.1.61 |
atmAtmSpvcVccVUNIAVUNI to associate the Egress part of the B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.62 |
atmAtmSpvcVccVUNIBVUNI to associate the Egress part of the A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.33.1.63 |
atmAtmSpvcVccTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.64 |
atmAtmSpvcVccTrafficShapingB2ATraffic Shaping Support in the B2A direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.65 |
atmAtmSpvcVccPriorityPriority of SPVC - priority-1 being highest priority .rw Enumeration .1.3.6.1.4.1.1751.2.18.6.33.1.66 |
cirAtmSpvcVccTableTable of Circuit Emulation to ATM Soft PVCs. SEQUENCE OF CirAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.34 |
cirAtmSpvcVccEntryRow definition of circuit emulation to ATM SPVC
connections. CirAtmSpvcVccEntry .1.3.6.1.4.1.1751.2.18.6.34.1 |
cirAtmSpvcVccRemoteCePortAddrThe ATM address supporting the corresponding far
end CES IWF process. If no address is supplied,
no attempts to establish the active SVC are
initiated. OCTET STRING .1.3.6.1.4.1.1751.2.18.6.34.1.1 |
cirAtmSpvcVccIfBInterface index for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port number, and CCC is the channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.34.1.2 |
cirAtmSpvcVccVpiBVPI value for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Valid
range is a number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.34.1.3 |
cirAtmSpvcVccVciBVCI value for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Valid
range is a number between 0 and 65535.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.34.1.4 |
cirAtmSpvcVccVoiceCompressionA2BVoice Compression Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.5 |
cirAtmSpvcVccSilenceDetectionA2Bsilence detection off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.6 |
cirAtmSpvcVccEchoCancellationA2BEcho Cancellation Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.7 |
cirAtmSpvcVccCngToneDetectionA2BCalling Tone Detection Algorithm,
one of the enum value, g726-32k(3)
is obsoleted on 01Mar99 such that
user would not be able to configure
CE-ATMrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.8 |
cirAtmSpvcVccCodingTranslationA2BCoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.9 |
cirAtmSpvcVccVoiceCompressionB2AVoice Compression Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.10 |
cirAtmSpvcVccSilenceDetectionB2Asilence detection off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.11 |
cirAtmSpvcVccEchoCancellationB2AEcho Cancellation Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.12 |
cirAtmSpvcVccCngToneDetectionB2ACalling Tone Detection Algorithm,
one of the enum value, g726-32k(3)
is obsoleted on 01Mar99 such that
user would not be able to configure
CE-ATMrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.13 |
cirAtmSpvcVccCodingTranslationB2ACoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.14 |
cirAtmSpvcVccFlowFlow Type, pointToMultipointA2B and
pointToMultipointB2A are for future support.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.15 |
cirAtmSpvcVccServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.16 |
cirAtmSpvcVccConnTypeThe type of connection: activeSvc - attempt calls,
whenever not established;
passiveSvc - accepts callsrw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.17 |
cirAtmSpvcVccOperStatusother - none of the types specified below;
establishmentInProgress - connection is not
operational, but call attempts are ongoing;
connected - connection is currently operational;
retriesExhausted - retry limit has been reached
and call attempts have ceased;
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated;
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.18 |
cirAtmSpvcVccRowStatusUsed to create and delete a soft PVCC. When this
object is set to 'active' an attempt is made to
set up the soft PVCC. When this object has the
value 'active' and is set to another value, any
set-up or connection in-progess is released.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.34.1.19 |
cirAtmSpvcVccViBVI to associate the Egress part of
the B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.34.1.20 |
cirAtmSpvcVccRetryIntervalThe time to wait before attempting to establish
the SVC after previous failed call attempt.
0 indicates retries will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.34.1.21 |
cirAtmSpvcVccRetryLimitA maximum limit on how many retries.
0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.34.1.22 |
cirAtmSpvcVccRestartrestart, the active SVC is released if necessary
and a new setup procedure is begun; or nooprw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.23 |
cirAtmSpvcVccRetryFailureIndicates how many attempts to establish the
connection have failed. It is reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.24 |
cirAtmSpvcVccReleaseCauseCAUSE field value of the last RELEASE message
received for this SVC.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.34.1.25 |
cirAtmSpvcVccReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVC.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.34.1.26 |
cirAtmSpvcVccReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.27 |
cirAtmSpvcVccStatsCellsEncodedHiACells encoded on side A- (High order portion )ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.28 |
cirAtmSpvcVccStatsCellsEncodedLoACells encoded on side A - ( Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.29 |
cirAtmSpvcVccStatsCellsDecodedHiACells decoded on side A - ( High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.30 |
cirAtmSpvcVccStatsCellsDecodedLoACells decoded on side A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.31 |
cirAtmSpvcVccStatsInCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.32 |
cirAtmSpvcVccStatsInCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.33 |
cirAtmSpvcVccStatsOutCellCountHiBValid cells transmitted on B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.34 |
cirAtmSpvcVccStatsOutCellCountLoBValid cells transmitted on B -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.35 |
cirAtmSpvcVccStatsTimerNumber of seconds since stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.36 |
cirAtmSpvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.37 |
cirAtmSpvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.38 |
cirAtmSpvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.39 |
cirAtmSpvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.40 |
cirAtmSpvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.41 |
cirAtmSpvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.42 |
cirAtmSpvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.43 |
cirAtmSpvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.44 |
cirAtmSpvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.45 |
cirAtmSpvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.46 |
cirAtmSpvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.47 |
cirAtmSpvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.34.1.48 |
cirAtmSpvcVccVUNIBVUNI to associate the Egress part of
the B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.34.1.49 |
cirAtmSpvcVccSarTypeBThis field will only be used when selecting voice
compression, in other cases it will be set to
aal1.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.50 |
cirAtmSpvcVccPriorityPriority of SPVC - priority-1 being highest priority .rw Enumeration .1.3.6.1.4.1.1751.2.18.6.34.1.51 |
vbrAtmSpvcTableTable of SPVC atm virtual channel connections SEQUENCE OF VbrAtmSpvcEntry .1.3.6.1.4.1.1751.2.18.6.35 |
vbrAtmSpvcEntryRow definition of atm SPVC VCC connections VbrAtmSpvcEntry .1.3.6.1.4.1.1751.2.18.6.35.1 |
vbrAtmSpvcRemoteVbrPortAddrremote VBR port nsap address implemening IWF, not
meaningful if passive type of connection OCTET STRING .1.3.6.1.4.1.1751.2.18.6.35.1.1 |
vbrAtmSpvcIfBInterface index for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.35.1.2 |
vbrAtmSpvcVpiBVPI value for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Valid
range is a number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.35.1.3 |
vbrAtmSpvcVciBVCI value for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Valid
range is a number between 0 and 65535.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.35.1.4 |
vbrAtmSpvcServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.5 |
vbrAtmSpvcPeakCellRateA2Bpeak cell rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.6 |
vbrAtmSpvcSusCellRateA2Bsustained rate - side A, in cell per secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.7 |
vbrAtmSpvcMaxBurstSizeA2Bmaximum burst size - side A, in cellsrw Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.8 |
vbrAtmSpvcPeakCellRateB2Apeak rate - side B, ATM trunk, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.9 |
vbrAtmSpvcSusCellRateB2Asustained rate - side B, ATM trunk, in cell per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.10 |
vbrAtmSpvcMaxBurstSizeB2Amaximum burst size - side B, ATM trunk, in cells.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.11 |
vbrAtmSpvcFlowtype of flowrw Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.12 |
vbrAtmSpvcConnTypeThe type of connection: activeSvc - attempt calls,
whenever not established;
passiveSvc - accepts callsrw Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.13 |
vbrAtmSpvcOperStatusother - none of the types specified below;
establishmentInProgress - connection is not
operational, but call attempts are ongoing;
connected - connection is currently operational;
retriesExhausted - retry limit has been reached
and call attempts have ceased;
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated;
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.14 |
vbrAtmSpvcRowStatusUsed to create and delete a soft PVCC. When this
object is set to 'active' an attempt is made to
set up the soft PVCC. When this object has the
value 'active' and is set to another value, any
set-up or connection in-progess is released.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.35.1.15 |
vbrAtmSpvcViBVI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.35.1.16 |
vbrAtmSpvcRetryIntervalthe time to wait before attempting to establish
the SVC after previous failed call attempt.
0 indicates retries will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.35.1.17 |
vbrAtmSpvcRetryLimita maximum limit on how many retries.
0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.35.1.18 |
vbrAtmSpvcRestartrestart, the active SVC is released if necessary
and a new setup procedure is begun; or nooprw Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.19 |
vbrAtmSpvcRetryFailureindicates how many attempts to establish the
connection have failed. It is reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.20 |
vbrAtmSpvcReleaseCauseCAUSE field value of the last RELEASE message
received for this SVCro INTEGER .1.3.6.1.4.1.1751.2.18.6.35.1.21 |
vbrAtmSpvcReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVCro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.35.1.22 |
vbrAtmSpvcReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.23 |
vbrAtmSpvcStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.24 |
vbrAtmSpvcStatsCellsEncodedLoAells encoded on side A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.25 |
vbrAtmSpvcStatsCellsDecodedHiACells decoded on side A - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.26 |
vbrAtmSpvcStatsCellsDecodedLoACells decoded on side A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.27 |
vbrAtmSpvcStatsInCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.28 |
vbrAtmSpvcStatsInCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.29 |
vbrAtmSpvcStatsOutCellCountHiBValid cells transmitted on B -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.30 |
vbrAtmSpvcStatsOutCellCountLoBValid cells transmitted on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.31 |
vbrAtmSpvcStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.32 |
vbrAtmSpvcStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.33 |
vbrAtmSpvcStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.34 |
vbrAtmSpvcStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.35 |
vbrAtmSpvcStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.36 |
vbrAtmSpvcStatsInOdometerCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.37 |
vbrAtmSpvcStatsInOdometerCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.38 |
vbrAtmSpvcStatsOutOdometerCellCountHiBValid Cells transmitted on B -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.39 |
vbrAtmSpvcStatsOutOdometerCellCountLoBValid Cells transmitted on B -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.40 |
vbrAtmSpvcStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.41 |
vbrAtmSpvcStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.42 |
vbrAtmSpvcStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.43 |
vbrAtmSpvcStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.35.1.44 |
vbrAtmSpvcVUNIBVUNI to associate the Egress part of the
B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.35.1.45 |
vbrAtmSpvcTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.46 |
vbrAtmSpvcPriorityPriority of SPVC - priority-1 being highest priority .rw Enumeration .1.3.6.1.4.1.1751.2.18.6.35.1.47 |
aal2TrunkConfigTableTable of terminal emulation to ATM network
IWF connections SEQUENCE OF Aal2TrunkConfigEntry .1.3.6.1.4.1.1751.2.18.6.36 |
aal2TrunkConfigEntryRow definition of terminal emulation to ATM
network IWF connections Aal2TrunkConfigEntry .1.3.6.1.4.1.1751.2.18.6.36.1 |
aal2TrunkConfigIfInterface Id of the Atm Side of the Aal2 Trunk. IntfIndex .1.3.6.1.4.1.1751.2.18.6.36.1.1 |
aal2TrunkConfigVpiVPI value for Atm side , the atm side,
of a atm trunk connection.
Valid range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.36.1.2 |
aal2TrunkConfigVciVCI value for the atm side, of a variable
bit rate-atm PVC VCC connection.
Valid range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.36.1.3 |
aal2TrunkConfigServiceTypeService/Queue types supported for Aal2 Trunk
connections.When using Vbr/Ubr type service
type oversubscription will have to be taken into
account for which nature of traffic going over the
Trunk should be known before handrw Enumeration .1.3.6.1.4.1.1751.2.18.6.36.1.4 |
aal2TrunkConfigPeakCellRateIgrpeak cell rate - atm side inp, in cell per
secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.5 |
aal2TrunkConfigSusCellRateIgrsustained rate - atm side inp, in cell per
secondrw Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.6 |
aal2TrunkConfigMaxBurstSizeIgrmaximum burst size - atm side inp, in cellsrw Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.7 |
aal2TrunkConfigPeakCellRateEgrpeak rate - atm side output, in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.8 |
aal2TrunkConfigSusCellRateEgrsustained rate - atm side output,in cell per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.9 |
aal2TrunkConfigMaxBurstSizeEgrmaximum burst size - atm side output, in cells.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.10 |
aal2TrunkConfigFlowFlow typerw Enumeration .1.3.6.1.4.1.1751.2.18.6.36.1.11 |
aal2TrunkConfigRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.36.1.12 |
aal2TrunkConfigConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated .
InactiveA2B-B2A: Both the A2B and B2A resource
interfaces are not in service.
InactiveA2B: The A2B resource interface is not in
service.
InactiveB2A: The B2A resource interface is not in
service.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.36.1.13 |
aal2TrunkConfigViBVI to associate the Egress part of the
A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.36.1.14 |
aal2TrunkConfigCnfrmTypeB2AThe following is the description of this field
This will be used in conjunction with the
service type field to get the correct
traffic behaviour. In the conformances the the 0 or
0plus1 refers to the clp bit in the cells.
If 0plus1 is the bucket reference then
the clp bit is ignored. If 0 is specified for
the bucket then check only clp=0 cells.
1: Best Effort will try to send all cellsin a
best effort way. This will follow the
Aqueman Algorithm
2: one-bucket-notag-0plus1 will use 1 bucket
i.e is the PCR(0+1) bucket and drop all
cells in excess.
3: two-bucket-notag-0plus1-0plus1 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0+1).
All cells conforming to both buckets will be
passed through. The rest will be dropped.
4: two-bucket-notag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which conform to both buckets
are passed through. The rest are dropped.
5: two-bucket-tag-0plus1-0 uses 2 buckets.
The 2 buckets are pcr(0+1) and scr(0) or
pcr(0). Cells which do not conform to the first
bucket are dropped. Cells which do not
conform to the 2nd bucket are tagged.
6: best-effort-tag. Tag all cells and then
do a best effort.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.36.1.15 |
aal2TrunkConfigVUNIBVUNI to associate the Egress part of the A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.36.1.16 |
aal2TrunkAvailBwIgrThe Avail Bandwidth for that interface in cells per sec.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.17 |
aal2TrunkAvailBwEgrThe Avail Bandwidth for that interface in
cells per sec.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.36.1.18 |
aal2TrunkGR303This flag is used to check if a GR303 Feature
is enabled for the trunk.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.36.1.19 |
aal2TrunkConfigOamStatusIndicates the OAM monitoring status of side A.
The 2 possible states are:
Unsupp: No monitoring enabled.
End-Pt: Atm side is only an end point, therefore
it will respond to AIS/RDI.
End-Seg-Pt: A side is both an end point and a
segment point.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.36.1.20 |
aal2TrunkConnFailureCauseBconnection status reason codero AtmConnFailureCause .1.3.6.1.4.1.1751.2.18.6.36.1.21 |
aal2TrunkCuTimerCuTimer represents 'combined use timer',
is set to zero such that every ATM cell
transmitted contains one, and only one,
AAL2 packet, and the first octet of the AAL2
packet header follows immediately after
the Start Field in the ATM cell payload. If the
AAL2 packet payload is less than 44 octets,
the remainder of the ATM cell payload
following the end of the AAL2 packet shall be
filled with zeros as padding.
Each increment of CuTimer means 5ms more to wait.
And cuTimer default value 4 means to wait 20ms
before the ATM cell is sent out.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.36.1.22 |
gr303Aal2PvcVccTableTable of Gr303 to AAL2 Cid monitor VCCs SEQUENCE OF Gr303Aal2PvcVccEntry .1.3.6.1.4.1.1751.2.18.6.37 |
gr303Aal2PvcVccEntryRow definition of circuit emulation to atm
connections. Gr303Aal2PvcVccEntry .1.3.6.1.4.1.1751.2.18.6.37.1 |
gr303Aal2PvcVccGr303IgIdGR303 interface group id on the GR303 side of the
connection INTEGER .1.3.6.1.4.1.1751.2.18.6.37.1.1 |
gr303Aal2PvcVccGr303CallRefThe call reference value to be used in the signaling
packets on the GR303 interface for the connection on
the AAL2CID corresponding to this connection INTEGER .1.3.6.1.4.1.1751.2.18.6.37.1.2 |
gr303Aal2PvcVccIfBInterface index for side B, the atm side, of a
circuit emulation-atm PVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.6.37.1.3 |
gr303Aal2PvcVccVpiBVPI value for side B, the atm side, of a
circuit emulation-atm PVC VCC connection. Valid
range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.37.1.4 |
gr303Aal2PvcVccVciBVCI value for side B, the atm side, of a
circuit emulation-atm PVC VCC connection. Valid
range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.37.1.5 |
gr303Aal2PvcVccAal2CidAal2 Cid Used to pack ce chan in an
Atm Trunk. This value will be unique
per Atm Trunk. This field will be applicable
when Aal type is chosen to be Standard Aal2. INTEGER .1.3.6.1.4.1.1751.2.18.6.37.1.6 |
gr303Aal2PvcVccRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.37.1.7 |
gr303Aal2PvcVccVoiceEncodingProfileProfile for use by voice/voiceband data.
Profile-3 and Profile-7 are ITU-T predefined profiles
which specify the voice compression and silence removal
algorithms. If custom profile is chosen all DSP specific
parameters have to be specified by the user. If default
profile is chosen all parameters on the AAL2
trunk, containing this CID, will be used.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.8 |
gr303Aal2PvcVccVoiceCompressionVoice Compression Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.9 |
gr303Aal2PvcVccSilenceDetectionsilence detection off/onrw Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.10 |
gr303Aal2PvcVccEchoCancellationEcho Cancellation Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.11 |
gr303Aal2PvcVccCngToneDetectionCalling Tone Detection Algorithmrw Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.12 |
gr303Aal2PvcVccCodingTranslationCoding rule translation type.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.13 |
gr303Aal2PvcVccConnectionStatusIndicates the current connections status.
Active: All interfaces through which the
connection is going are in service.
Inactive: One of the end interfaces of the
connection is not in service.
The rest of the states apply to connections going
through resource interfaces like DSP2 and FEC. These
interfaces are dynamically allocated.
If an end interface and the resource interfaces
are out of service, the status will be inactive
because the end interfaces take priority.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.14 |
gr303Aal2PvcVccAltLineTypeAnalog Line Termination Line Type on the subscriber side.
The ABCD bit codes for diffterent signal types depend on
the analog line type. The analog type can be overwritten by an EOC
message from the IDTrw Enumeration .1.3.6.1.4.1.1751.2.18.6.37.1.15 |
atmAtmSpvcVpcTableTable of SPVC ATM virtual path connections. SEQUENCE OF AtmAtmSpvcVpcEntry .1.3.6.1.4.1.1751.2.18.6.38 |
atmAtmSpvcVpcEntryRow definition of ATM SPVC VPC connections. AtmAtmSpvcVpcEntry .1.3.6.1.4.1.1751.2.18.6.38.1 |
atmAtmSpvcVpcVpiAVPI value for side A of an ATM SPVC VPC connection.
Valid range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.1 |
atmAtmSpvcVpcRemoteAtmPortAddrRemote ATM port NSAP address, not meaningful if
passive type of connection. OCTET STRING .1.3.6.1.4.1.1751.2.18.6.38.1.2 |
atmAtmSpvcVpcIfBInterface index for side B of an ATM SPVC VPC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
path number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.6.38.1.3 |
atmAtmSpvcVpcVpiBVPI value for side B of an ATM SPVC VPC connection.
Valid range is a number between 0 and 4095.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.4 |
atmAtmSpvcVpcServiceTypeA2BService type, ATM port.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.5 |
atmAtmSpvcVpcSarTypeA2BSAR type used in ATM adaption, ATM port.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.6 |
atmAtmSpvcVpcPeakCellRateA2BPeak cell rate - side A, ATM port, in cells per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.7 |
atmAtmSpvcVpcSusCellRateA2BSustained cell rate - side A, ATM port, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.8 |
atmAtmSpvcVpcMaxBurstSizeA2BMaximum burst size - side A, ATM port, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.9 |
atmAtmSpvcVpcFrwdErrCorrectionA2BForward error correction scheme, ATM port side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.10 |
atmAtmSpvcVpcServiceTypeB2AService type, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.11 |
atmAtmSpvcVpcSarTypeB2ASAR type used in ATM adaption, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.12 |
atmAtmSpvcVpcPeakCellRateB2APeak cell rate - side B, ATM trunk, in cells per
second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.13 |
atmAtmSpvcVpcSusCellRateB2ASustained cell rate - side B, ATM trunk, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.14 |
atmAtmSpvcVpcMaxBurstSizeB2AMaximum burst size - side A, ATM trunk, in cells
per second.rw Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.15 |
atmAtmSpvcVpcFrwdErrCorrectionB2AForward error correction scheme, ATM trunk side.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.16 |
atmAtmSpvcVpcFlowType of flow, pointToMultipointA2B is for future
support.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.17 |
atmAtmSpvcVpcTypeType of connection.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.18 |
atmAtmSpvcVpcConnTypeThe type of connection:
activeSvc - attempt calls, whenever not
established.
passiveSvc - accept calls.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.19 |
atmAtmSpvcVpcLeafReferenceAn arbitrary integer which serves to distinguish
the mulitple leaves attached to a root of a
point-to-multipoint SPVC. If point-to-point SPVC,
the value should be 1.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.20 |
atmAtmSpvcVpcOperStatusThe operation status of the connection:
other - none of the types specified below.
establishmentInProgress - connection is not
operational, but call attempts are ongoing.
connected - connection is currently operational.
retriesExhausted - retry limit has been reached
and call attempts have ceased.
noAddressSupplied - no remote address has been
configured, so no call attempts are initiated.
lowerLayerDown - SPVC handler is not operational.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.21 |
atmAtmSpvcVpcRowStatusUsed to create and delete a soft PVC. When this
object is set to 'active', an attempt is made to
set up the soft PVC. When this object has the
value 'active' and is set to another value, any
setup or connection in-progress is released.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.6.38.1.22 |
atmAtmSpvcVpcRemoteSelectTypeIndicates whether the remote VPI values are to
be used at the destination. If 'any' is used, the
destination switch will choose the VPI values.
In such a case, once the SPVC is connected, the
value of this object will change to 'required',
such that the same VPI values will continue to
be used even if the connection is torn down and
re-established. If the value 'required' is
specified, the values: atmAtmSpvcVpcRemoteVpi and
must be supplied and are used
at the destination.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.23 |
atmAtmSpvcVpcRemoteVpiVPI value to be used at the destination of an
ATM SPVC VPC connection. Valid range is a number
between 0 and 4095. If atmAtmSpvcVpcRemoteSelectType
is configured as 'any', then this value is not
relevant.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.24 |
atmAtmSpvcVpcRetryIntervalThe time to wait before attempting to establish
the SVC after a previous failed call attempt. A
value of 0 indicates retries will be attempted immediately.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.25 |
atmAtmSpvcVpcRetryLimitA maximum limit on how many retries should be
attempted. A value of 0 indicates no limit.rw INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.26 |
atmAtmSpvcVpcRestartThe active SVC is released, if necessary, and a
new setup procedure is begun if 'restart',
otherwise, noop.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.27 |
atmAtmSpvcVpcRetryFailureIndicates how many attempts to establish the
connection have failed. It it reset whenever a
connection is successfully established or the SVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.28 |
atmAtmSpvcVpcReleaseCauseCAUSE field value of the last RELEASE message
received for this SVC.ro INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.29 |
atmAtmSpvcVpcReleaseDiagDIAGNOSTICS field value of the last RELEASE
message received for this SVC.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.6.38.1.30 |
atmAtmSpvcVpcReleaseRelease the connnection established on the endpoint
and if the endpoint is Active, do not retry.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.31 |
atmAtmSpvcVpcStatsInCellCountHiAValid Cells received on A - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.32 |
atmAtmSpvcVpcStatsInCellCountLoAValid Cells received on A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.33 |
atmAtmSpvcVpcStatsOutCellCountHiAValid cells transmitted on A -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.34 |
atmAtmSpvcVpcStatsOutCellCountLoAValid cells transmitted on A -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.35 |
atmAtmSpvcVpcStatsInCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.36 |
atmAtmSpvcVpcStatsInCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.37 |
atmAtmSpvcVpcStatsOutCellCountHiBValid cells transmitted on B -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.38 |
atmAtmSpvcVpcStatsOutCellCountLoBValid cells transmitted on B -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.39 |
atmAtmSpvcVpcStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.40 |
atmAtmSpvcVpcStatsFrwdErrCrrctnRateA2BDisplays the Forward error correction rate being
used by the FEC module in the A2B direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.41 |
atmAtmSpvcVpcStatsFrwdErrCrrctnRateB2ADisplays the Forward error correction rate being
used by the FEC module in the B2A direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.42 |
atmAtmSpvcVpcStatsInOdometerCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.43 |
atmAtmSpvcVpcStatsInOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.44 |
atmAtmSpvcVpcStatsOutOdometerCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.45 |
atmAtmSpvcVpcStatsOutOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.46 |
atmAtmSpvcVpcStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.47 |
atmAtmSpvcVpcStatsInOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.48 |
atmAtmSpvcVpcStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.49 |
atmAtmSpvcVpcStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.50 |
atmAtmSpvcVpcStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.51 |
atmAtmSpvcVpcStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.52 |
atmAtmSpvcVpcViAVI to associate the Egress part of the B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.53 |
atmAtmSpvcVpcViBVI to associate the Egress part of the A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.54 |
atmAtmSpvcVpcStatsCellsDroppedACells Dropped on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.55 |
atmAtmSpvcVpcStatsCellsTaggedACells Tagged on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.56 |
atmAtmSpvcVpcStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.57 |
atmAtmSpvcVpcStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.6.38.1.58 |
atmAtmSpvcVpcVUNIAVUNI to associate the Egress part of the B2A connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.59 |
atmAtmSpvcVpcVUNIBVUNI to associate the Egress part of the A2B connection .rw INTEGER .1.3.6.1.4.1.1751.2.18.6.38.1.60 |
atmAtmSpvcVpcTrafficShapingA2BTraffic Shaping Support in the A2B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.61 |
atmAtmSpvcVpcTrafficShapingB2ATraffic Shaping Support in the B2A direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.62 |
atmAtmSpvcVpcPriorityPriority of SPVC - priority-1 being highest priority .rw Enumeration .1.3.6.1.4.1.1751.2.18.6.38.1.63 |
intfAtmPvcConnDisplayTableList of Pvc Connections on an Interface. SEQUENCE OF IntfAtmConnDisplayEntry .1.3.6.1.4.1.1751.2.18.6.39 |
intfAtmPvcConnDisplayEntryGives list of pvc going towards the backplane
on a particluar interface IntfAtmConnDisplayEntry .1.3.6.1.4.1.1751.2.18.6.39.1 |
intfAtmPvcConnDisplaySlotSlot of the particular interface Integer32 .1.3.6.1.4.1.1751.2.18.6.39.1.1 |
intfAtmPvcConnDisplayPortPort of the particular interface Integer32 .1.3.6.1.4.1.1751.2.18.6.39.1.2 |
intfAtmPvcConnDisplayChannelChannel of the particular interface Integer32 .1.3.6.1.4.1.1751.2.18.6.39.1.3 |
intfAtmPvcConnDisplayVpiVPI value for connection on Intf
Valid range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.6.39.1.4 |
intfAtmPvcConnDisplayVciVCI value for connection on Intf
Valid range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.6.39.1.5 |
intfAtmPvcConnDisplayFlowTypeFlow type:Indicates Flow Towards the Back Plane
cnctnValid: Traffic flow towards BP is enabled.
cnctnNull: Traffic flow towards BP is disabled.
cnctnPtmpValid: Traffic flow towards BP is enabled
and it is point to multipoint
connection.
cnctnPtmpNull: Traffic flow towards BP is disabled
and it is point to multipoint
connection.ro Enumeration .1.3.6.1.4.1.1751.2.18.6.39.1.6 |
userServiceConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.7 |
sysTraps OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.8 |
systemEvents OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.8.1 |
moduleEvents OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.8.2 |
interfaceEvents OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.8.3 |
connectionEvents OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.8.4 |
pgtStandbySelectionStandby selection method determines the
order of selection of standby when primary interface
fails. The options are:
sequential
standby to the last one,
latest_used
oldest_used
random \255 randomly select one,
explicit
DEFVAL { sequential }
::= { protectionGroupEntry 4 }
pgtRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTIONrw Enumeration .1.3.6.1.4.1.1751.2.18.8.4.87 |
sysStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.9 |
equipStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.10 |
ds3PortStatsTableTable of statisics for a DS3 port SEQUENCE OF Ds3PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.1 |
ds3PortStatsEntryRow definition for the DS3 port statistics
table Ds3PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.1.1 |
ds3PortStatsIdPort ID - Slot/Port (SSPP) Integer32 .1.3.6.1.4.1.1751.2.18.10.1.1.1 |
ds3PortStatsTimerThe number of seconds that have elapsed since the
beginning of the current error-measurement period.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.1.1.2 |
ds3PortStatsCurrentSEFSsseverely errored framing secondsro Integer32 .1.3.6.1.4.1.1751.2.18.10.1.1.3 |
ds3PortStatsCurrentLCVsLine coding violations encounteredro Integer32 .1.3.6.1.4.1.1751.2.18.10.1.1.4 |
ds3PortStatsCurrentLESsLine errored secondsro Integer32 .1.3.6.1.4.1.1751.2.18.10.1.1.5 |
ds1PortStatsTableTable of statisics for a DS1 port SEQUENCE OF Ds1PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.2 |
ds1PortStatsEntryRow definition for the DS1 port statistics
table Ds1PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.2.1 |
ds1PortStatsIdPort ID - Slot/Port (SSPP) Integer32 .1.3.6.1.4.1.1751.2.18.10.2.1.1 |
ds1PortStatsTimerThe number of seconds that have elapsed since the
beginning of the current error-measurement period.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.2.1.2 |
ds1PortStatsCurrentESsThe number of Errored Seconds, encountered by
a DS1 interface.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.2.1.3 |
ds1PortStatsCurrentSESsThe number of Severely Errored Seconds encoun-
tered by a DS1 interface.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.2.1.4 |
ds1PortStatsCurrentLCVsThe number of Line Code Violations (LCVs) en-
countered by a DS1 interface.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.2.1.5 |
oc3PortStatsTableTable of statisics for a OC3 port SEQUENCE OF Oc3PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.3 |
oc3PortStatsEntryRow definition for the OC3 port statistics
table Oc3PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.3.1 |
oc3PortStatsIdPort ID - Slot/Port (SSPP) Integer32 .1.3.6.1.4.1.1751.2.18.10.3.1.1 |
oc3PortStatsSectionBip8Errssection sublayer BIP8 errors.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.3.1.2 |
oc3PortStatsLineBip8Errsline sublayer BIP8 errors.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.3.1.3 |
oc3PortStatsPathBip8Errspath sublayer BIP8 errors.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.3.1.4 |
oc3PortStatsLineFebeCountline sublayer FEBE count.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.3.1.5 |
oc3PortStatsPathFebeCountpath sublayer FEBE count.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.3.1.6 |
oc3PortStatsTimerThe number of seconds that have elapsed since the
beginning of the current error-measurement period.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.3.1.7 |
msPortStatsTableTable of statisics for a MS port SEQUENCE OF MsPortStatsEntry .1.3.6.1.4.1.1751.2.18.10.4 |
msPortStatsEntryRow definition for the MS port statistics
table MsPortStatsEntry .1.3.6.1.4.1.1751.2.18.10.4.1 |
msPortStatsIdPort ID - Slot/Port (SSPP) Integer32 .1.3.6.1.4.1.1751.2.18.10.4.1.1 |
msPortStatsFrameErrorsP-bit severely errored secondsro Integer32 .1.3.6.1.4.1.1751.2.18.10.4.1.4 |
msPortStatsOutOfFrameSecondsseverely errored framing secondsro Integer32 .1.3.6.1.4.1.1751.2.18.10.4.1.5 |
msPortStatsTimerThe number of seconds that have elapsed since the
beginning of the current error-measurement period.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.4.1.6 |
e3PortStatsTableTable of statisics for a E3 port SEQUENCE OF E3PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.5 |
e3PortStatsEntryRow definition for the E3 port statistics
table E3PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.5.1 |
e3PortStatsIdPort ID - Slot/Port (SSPP) Integer32 .1.3.6.1.4.1.1751.2.18.10.5.1.1 |
e3PortStatsTimerThe number of seconds that have elapsed since the
beginning of the current error-measurement period.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.5.1.2 |
e3PortStatsCurrentSEFSsseverely errored framing secondsro Integer32 .1.3.6.1.4.1.1751.2.18.10.5.1.3 |
e3PortStatsCurrentLCVsLine coding violations encounteredro Integer32 .1.3.6.1.4.1.1751.2.18.10.5.1.4 |
e3PortStatsCurrentLESsLine errored secondsro Integer32 .1.3.6.1.4.1.1751.2.18.10.5.1.5 |
e1PortStatsTableTable of statisics for a E1 port SEQUENCE OF E1PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.6 |
e1PortStatsEntryRow definition for the E1 port statistics
table E1PortStatsEntry .1.3.6.1.4.1.1751.2.18.10.6.1 |
e1PortStatsIdPort ID - Slot/Port (SSPP) Integer32 .1.3.6.1.4.1.1751.2.18.10.6.1.1 |
e1PortStatsTimerThe number of seconds that have elapsed since the
beginning of the current error-measurement period.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.6.1.2 |
e1PortStatsCurrentESsThe number of Errored Seconds, encountered by
a E1 interface.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.6.1.3 |
e1PortStatsCurrentSESsThe number of Severely Errored Seconds encoun-
tered by a E1 interface.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.6.1.4 |
e1PortStatsCurrentLCVsThe number of Line Code Violations (LCVs) en-
countered by a E1 interface.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.6.1.5 |
ethernetPortStatsTableStatisics for a collection of ethernet-like
interfaces attached to a particular system. SEQUENCE OF EthernetPortStatsEntry .1.3.6.1.4.1.1751.2.18.10.7 |
ethernetPortStatsEntryStatistics for a particular interface to an
ethernet-like medium. EthernetPortStatsEntry .1.3.6.1.4.1.1751.2.18.10.7.1 |
ethernetPortStatsIdAn index value that uniquely identifies an
interface to an ethernet-like medium. The
interface identified by a particular value of
this index is the same interface as identified
by the same value of ethernetPortId. Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.1 |
ethernetPortStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.2 |
ethernetPortStatsAlignmentErrorsA count of frames received on a particular
interface that are not an integral number of
octets in length and do not pass the FCS check.
The count represented by an instance of this
object is incremented when the alignmentError
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.3 |
ethernetPortStatsFCSErrorsA count of frames received on a particular
interface that are an integral number of
octets in length but do not pass the FCS check.
The count represented by an instance of this
object is incremented when the frameCheckError
status is returned by the MAC service to the
LLC (or other MAC user). Received frames for
which multiple error conditions obtain are,
according to the conventions of IEEE 802.3
Layer Management, counted exclusively according
to the error status presented to the LLC.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.4 |
ethernetPortStatsSingleCollisionFramesA count of successfully transmitted frames on
a particular interface for which trnasmission
is inhibited by exactly one collision.
A frame that is counted by an instance of this
object is also counted by the corresponding
instance of either the ifOutUcastPkts,
IfOutMulticastPkts, or ifOutBroadcastPkts,
and is not counted by the corresponding
instance of the
ethernetPortStatsMulitipleCollisionFrames object.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.5 |
ethernetPortStatsMultipleCollisionFramesA count of successfully transmitted frames on
a particular interface for which trnasmission
is inhibited by more than one collision.
A frame that is counted by an instance of this
object is also counted by the corresponding
instance of either the ifOutUcastPkts,
IfOutMulticastPkts, or ifOutBroadcastPkts,
and is not counted by the corresponding
instance of the
ethernetPortStatsSingleCollisionFrames object.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.6 |
ethernetPortStatsSQETestErrorsA count of times that the SQE TEST ERROR message
is generated by the PLS sublayer for a particular
interface. The SQE TEST ERROR message is
defined in section 7.2.2.2.4 of ANSI/IEEE
802.3-1985 and its generation is described
in section 7.2.4.6 of the same document.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.7 |
ethernetPortStatsDeferredTransmissionsA count of frames for which the first transmission
attempt on a particluar interface is delayed
because the medium is busy.
the count represented by an instance of this
object does not include frames involved in
collisions.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.8 |
ethernetPortStatsLateCollisionsThe number of times that a collision is detected
on a particular interface later than 512 bit-times
into the transmission of a packet.
Five hundred and twelve bit-times corresponds to
51.2 microseconds on a 10 Mbit/s system. A (late)
collision included in a count represented by an
instance of this object is also considered as a
(generic) collision for purposes of other
collision-related statistics.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.9 |
ethernetPortStatsExcessiveCollisionsA count of frames for which transmission on a
particular interface fails due to excessive
collisions.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.10 |
ethernetPortStatsInternalMacTransmitErrorsA count of frames for which transmission on a
particular interface fails due to an internal
MAC sublayer transmit error. A frame is only
counted by an instance of this object if it is
not counted by the corresponding instance of
either the ethernetPortStatsLateCollisions object,
the ethernetPortStatsExcessiveCollisions object,
or the ethernetPortStatsCarrierSenseErrors object.
The precise meaning of the count represented by
an instance of this object is implementation-
specific. In particular, an instance of this
object may represent a count of transmission
errors on a particular interface that are not
otherwise counted.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.11 |
ethernetPortStatsCarrierSenseErrorsThe number of times that the carrier sense
condition was lost or never asserted when
attempting to transmit a frame on a particular
interface.
The count represented by an instance of this
object is incremented at most once per
transmission attempt, even if the carrier sense
condition fluctuates during a transmission
attempt.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.12 |
ethernetPortStatsFrameTooLongsA count of frames received on a particular
interface that exceed the maximum permitted
frame size.
The count represented by an instance of this
object is incremented when the frameTooLong status
is returned by the MAC service to the LLC (or
other MAC user). Received frames for which
multiple error conditions obtain are, according
to the conventions of IEEE 802.3 Layer
Management, counted exclusively according to the
error status presented to the LLC.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.13 |
ethernetPortStatsInternalMacReceiveErrorsA count of frames for which reception on a
particular interface fails due to an internal
MAC sublayer receive error. A frame is only
counted by an instance of this object if it is not
counted by the corresponding instance of either
the ethernetPortStatsFrameTooLongs object, the
ethernetPortStatsAlignmentErrors object, or the
ethernetPortStatsFCSErrors object.
The precise meaning of the count represented by
an instance of this object is implementation-
specific. In particular, an instance of this
object may represent a count of receive errors
on a particular interface that are not
otherwise counted.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.7.1.14 |
oc3APSPairStatsTableTable of statisics for a OC3 port SEQUENCE OF Oc3APSPairStatsEntry .1.3.6.1.4.1.1751.2.18.10.8 |
oc3APSPairStatsEntryRow definition for the OC3 port statistics
table Oc3APSPairStatsEntry .1.3.6.1.4.1.1751.2.18.10.8.1 |
oc3APSPairStatsIdWorking Port ID - Slot/Port (SSPP) Integer32 .1.3.6.1.4.1.1751.2.18.10.8.1.1 |
oc3APSPairWorkingSFDurationDuration in seconds for which the Work port
has been in Signal Failure statero Integer32 .1.3.6.1.4.1.1751.2.18.10.8.1.2 |
oc3APSPairWorkingSDDurationDuration in seconds for which the Work port
has been in Signal Degradation statero Integer32 .1.3.6.1.4.1.1751.2.18.10.8.1.3 |
oc3APSPairProtectionSFDurationDuration in seconds for which the Prot
port has been in Signal Failure statero Integer32 .1.3.6.1.4.1.1751.2.18.10.8.1.4 |
oc3APSPairProtectionSDDurationDuration in seconds for which
the Prot port has been in Signal Degradation statero Integer32 .1.3.6.1.4.1.1751.2.18.10.8.1.5 |
oc3APSPairTransmitK1K2BytesThe k1 / k2 bytes being transmitted by the prot
port to the remote port.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.10.8.1.6 |
oc3APSPairReceiveK1K2Bytesk1 / k2 bytes from the received SONET header
on the protection port. k1 / k2 are used for
the APS communication protocol.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.10.8.1.7 |
oc3APSPairSwitchOverCountNumber of times the APS pair has switched over
since last configuration.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.8.1.8 |
viprVpnStatsTableStatistics collected per vpn based SEQUENCE OF ViprVpnStatsEntry .1.3.6.1.4.1.1751.2.18.10.9 |
viprVpnStatsEntryStatistics collected per vpn based ViprVpnStatsEntry .1.3.6.1.4.1.1751.2.18.10.9.1 |
viprVpnStatsTimerA timeout value in which the RS Module
must reply to statistics requests.ro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.1 |
viprVpnStatsIcmpOutEchoRPsEcho Replyro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.2 |
viprVpnStatsIcmpOutDestURsDestination unreachablero Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.3 |
viprVpnStatsIcmpOutSrcQSource Quenchesro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.4 |
viprVpnStatsIcmpOutRedirectsRedirect message typero Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.5 |
viprVpnStatsIcmpOutEchoRQsEcho Requestsro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.6 |
viprVpnStatsIcmpOutTimeXsTime exceededro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.7 |
viprVpnStatsIcmpOutParampsParameter problemro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.8 |
viprVpnStatsIcmpOutTimeRQsTimestamp requestsro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.9 |
viprVpnStatsIcmpOutTimeRPsTimestamp repliesro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.10 |
viprVpnStatsIcmpOutInfoRQsInformation Requestro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.11 |
viprVpnStatsIcmpOutInfoRPsEcho Replyro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.12 |
viprVpnStatsIcmpOutMaskRQsMask Requestro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.13 |
viprVpnStatsIcmpOutMaskRPsMask Replyro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.14 |
viprVpnStatsIcmpOutErrorsunrecognized ICMP typero Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.15 |
viprVpnStatsIcmpInErrorserror in received icmp messagero Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.16 |
viprVpnStatsIcmpInEchoRQsreceived echo requestro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.17 |
viprVpnStatsIcmpInAddrMasksreceived mask requestro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.18 |
viprVpnStatsIcmpInAddrMaskRepsreceived mask replyro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.19 |
viprVpnStatsIcmpInEchoRepsreceived echo repliesro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.20 |
viprVpnStatsIcmpInDestUnreachsreceived destination unreacheable messagero Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.21 |
viprVpnStatsIcmpInSrcQuenchsreceived source quenchro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.22 |
viprVpnStatsIcmpInTimeExcdsreceived time exceeded messagero Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.23 |
viprVpnStatsIcmpInParamProbsreceived parameter problem messagero Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.24 |
viprVpnStatsIcmpInTimeStampsreceived time stamp requestro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.25 |
viprVpnStatsIcmpInTimeStampsRepsreceived time stamp repliesro Integer32 .1.3.6.1.4.1.1751.2.18.10.9.1.26 |
intfStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.11 |
atmIfStatsTableTable of statistics for an atmUni interface SEQUENCE OF AtmIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.1 |
atmIfStatsEntryRow definition for the atmUni statistics
table AtmIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.1.1 |
atmIfStatsIdInterface index (SSPPCCC) to the atmUni
statistics table IntfIndex .1.3.6.1.4.1.1751.2.18.11.1.1.1 |
atmIfStatsValidCellsInHiNumber of valid cells received on the channel -
High Wordro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.2 |
atmIfStatsValidCellsInLoNumber of valid cells received on the channel -
low Wordro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.3 |
atmIfStatsErroredCellsInNumber of errored cells received on the channelro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.4 |
atmIfStatsMismatchedCellsInNumber of Vpi/Vci translation errors on input
cells.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.5 |
atmIfStatsNullCellsOutHiNumber of null cells sent out on the channel -
High Wordro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.6 |
atmIfStatsNullCellsOutLoNumber of null cells sent out on the channel -
Low Wordro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.7 |
atmIfStatsValidCellsOutHiNumber of valid cells sent out on the channel -
High Wordro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.8 |
atmIfStatsValidCellsOutLoNumber of valid cells sent out on the channel -
Low Wordro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.9 |
atmIfStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.1.1.10 |
frUniStatsTableTable of statistics for a Frame Relay UNI
Interface SEQUENCE OF FrUniStatsEntry .1.3.6.1.4.1.1751.2.18.11.2 |
frUniStatsEntryRow definition for the Frame Realy UNI statistics
table FrUniStatsEntry .1.3.6.1.4.1.1751.2.18.11.2.1 |
frUniStatsIdInterface index (SSPPCCC) to the frame relay UNI
statistics table IntfIndex .1.3.6.1.4.1.1751.2.18.11.2.1.1 |
frUniStatsTimerTime, in seconds, since last reset.ro INTEGER .1.3.6.1.4.1.1751.2.18.11.2.1.9 |
frUniStatsCellsMismatchednumber of cells not matched to provisioned DLCIs.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.10 |
frUniStatsErroredFramesnumber of errored frames.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.11 |
frUniStatsCellsEncodedHinumber of cells encoded - (High order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.12 |
frUniStatsCellsEncodedLonumber of cells encoded - (Low order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.13 |
frUniStatsFramesEncodedHinumber of frames encoded - (High order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.14 |
frUniStatsFramesEncodedLonumber of frames encoded - (Low order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.15 |
frUniStatsCellsDecodedHinumber of cells decoded - (High order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.16 |
frUniStatsCellsDecodedLonumber of cells decoded - (Low order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.17 |
frUniStatsFramesDecodedHinumber of frames decoded - (High order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.18 |
frUniStatsFramesDecodedLonumber of frames decoded - (Low order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.19 |
frUniStatsAAL5Errorsnumber of aal5 PDUs with invalid byte count
or CRC-32.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.2.1.20 |
cirEmIfStatsTableTable of statistics for an cirEm interface SEQUENCE OF CirEmIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.3 |
cirEmIfStatsEntryRow definition for the cirEm statistics
table CirEmIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.3.1 |
cirEmIfStatsIdInterface index (SSPPCCC) to the cirEm
statistics table IntfIndex .1.3.6.1.4.1.1751.2.18.11.3.1.1 |
cirEmIfStatsCellsEncodedHiIncoming cells from the outside media to the
i/o portro Integer32 .1.3.6.1.4.1.1751.2.18.11.3.1.2 |
cirEmIfStatsCellsEncodedLoIncoming cells from the outside media to the
i/o portro Integer32 .1.3.6.1.4.1.1751.2.18.11.3.1.3 |
cirEmIfStatsCellsDecodedHiOutgoing cells from the i/o port to the outside
mediaro Integer32 .1.3.6.1.4.1.1751.2.18.11.3.1.4 |
cirEmIfStatsCellsDecodedLoOutgoing cells from the i/o port to the outside
mediaro Integer32 .1.3.6.1.4.1.1751.2.18.11.3.1.5 |
cirEmIfStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.3.1.6 |
vbrIfStatsTableTable of statistics for an vbr interface SEQUENCE OF VbrIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.4 |
vbrIfStatsEntryRow definition for the vbr statistics
table VbrIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.4.1 |
vbrIfStatsIdInterface index (SSPPCCC) to the vbr
statistics table IntfIndex .1.3.6.1.4.1.1751.2.18.11.4.1.1 |
vbrIfStatsCellsEncodedHiIncoming cells from the outside media to the
i/o portro Integer32 .1.3.6.1.4.1.1751.2.18.11.4.1.2 |
vbrIfStatsCellsEncodedLoIncoming cells from the outside media to the
i/o portro Integer32 .1.3.6.1.4.1.1751.2.18.11.4.1.3 |
vbrIfStatsCellsDecodedHiOutgoing cells from the i/o port to the outside
mediaro Integer32 .1.3.6.1.4.1.1751.2.18.11.4.1.4 |
vbrIfStatsCellsDecodedLoOutgoing cells from the i/o port to the outside
mediaro Integer32 .1.3.6.1.4.1.1751.2.18.11.4.1.5 |
vbrIfStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.4.1.6 |
frLmiStatsTableTable of statistics for a Frame Relay LMI
Interface SEQUENCE OF FrLmiStatsEntry .1.3.6.1.4.1.1751.2.18.11.5 |
frLmiStatsEntryRow definition for the Frame Realy LMI statistics
table FrLmiStatsEntry .1.3.6.1.4.1.1751.2.18.11.5.1 |
frLmiStatsIdInterface index (SSPPCCC) to the frame relay LMI
statistics table IntfIndex .1.3.6.1.4.1.1751.2.18.11.5.1.1 |
frLmiStatsEnqRxnumber of STATUS ENQ messages receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.5.1.2 |
frLmiStatsEnqTxnumber of STATUS ENQ messages transmittedro Integer32 .1.3.6.1.4.1.1751.2.18.11.5.1.3 |
frLmiStatsStatusRxnumber of STATUS messages receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.5.1.4 |
frLmiStatsStatusTxnumber of STATUS messages transmittedro Integer32 .1.3.6.1.4.1.1751.2.18.11.5.1.5 |
frLmiStatsAsyncRxnumber of ASYNC STATUS messages receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.5.1.6 |
frLmiStatsAsyncTxnumber of ASYNC STATUS messages transmittedro Integer32 .1.3.6.1.4.1.1751.2.18.11.5.1.7 |
frLmiStatsPktDiscThe number of lmi messages discarded due to
invalid length, receive sequence numbers, or
other error.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.5.1.8 |
frLmiStatsT391ExpLink integrity verification polling timer expiryro INTEGER .1.3.6.1.4.1.1751.2.18.11.5.1.9 |
frLmiStatsT392ExpPolling verification timer expiryro INTEGER .1.3.6.1.4.1.1751.2.18.11.5.1.10 |
frLmiStatsLinkResetNumber of times interface operational status was
in service after system startup.ro INTEGER .1.3.6.1.4.1.1751.2.18.11.5.1.11 |
frLmiStatsTimerTime since last reset for statistics - in secondsro INTEGER .1.3.6.1.4.1.1751.2.18.11.5.1.12 |
bridgeStatsTableTable of statistics for a bridge interface. SEQUENCE OF BridgeStatsEntry .1.3.6.1.4.1.1751.2.18.11.6 |
bridgeStatsEntryRow definition for the bridge interface statistics
table BridgeStatsEntry .1.3.6.1.4.1.1751.2.18.11.6.1 |
bridgeStatsIdInterface index (SSPPCCC) to the bridge Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.1 |
bridgeStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.2 |
bridgeStatsBasePortDelayExceededDiscardsHiThe number of frames discarded by this port due
to excessive transit delay through the bridge. It
is incremented by both transparent and source
route bridges. High-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.8 |
bridgeStatsBasePortDelayExceededDiscardsLoThe number of frames discarded by this port due
to excessive transit delay through the bridge. It
is incremented by both transparent and source
route bridges. Low-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.9 |
bridgeStatsBasePortMtuExceededDiscardsHiThe number of frames discarded by this port due
to an excessive size. It is incremented by both
transparent and source route bridges. High-order
32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.10 |
bridgeStatsBasePortMtuExceededDiscardsLoThe number of frames discarded by this port due
to an excessive size. It is incremented by both
transparent and source route bridges. Low-order
32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.11 |
bridgeStatsTpPortInFramesHiThe number of frames that have been received by
this port from its segment. Note that a frame
received on the interface corresponding to this
port is only counted by this object if and only
if it is for a protocol being processed by the
local bridging function, including bridge
management frames. High-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.12 |
bridgeStatsTpPortInFramesLoThe number of frames that have been received by
this port from its segment. Note that a frame
received on the interface corresponding to this
port is only counted by this object if and only
if it is for a protocol being processed by the
local bridging function, including bridge
management frames. Low-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.13 |
bridgeStatsTpPortOutFramesHiThe number of frames that have been transmitted
by this port to its segment. Note that a frame
transmitted on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function, including bridge management
frames. High-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.14 |
bridgeStatsTpPortOutFramesLoThe number of frames that have been transmitted
by this port to its segment. Note that a frame
transmitted on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function, including bridge management
frames. Low-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.15 |
bridgeStatsTpPortInDiscardsHiCount of valid frames received which were
discarded (i.e., filtered) by the Forwarding
Process. High-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.16 |
bridgeStatsTpPortInDiscardsLoCount of valid frames received which were
discarded (i.e., filtered) by the Forwarding
Process. Low-order 32 bits.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.6.1.17 |
dbCirEmIfStatsTableTable of statistics for a dbCirEm interface. SEQUENCE OF DbCirEmIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.7 |
dbCirEmIfStatsEntryRow definition for the dbCirEm statistics table. DbCirEmIfStatsEntry .1.3.6.1.4.1.1751.2.18.11.7.1 |
dbCirEmIfStatsIdInterface index (SSPPCCC) to the dbCirEm
statistics table. IntfIndex .1.3.6.1.4.1.1751.2.18.11.7.1.1 |
dbCirEmIfStatsCellsEncodedHiIncoming cells from the outside media to the
i/o port.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.7.1.2 |
dbCirEmIfStatsCellsEncodedLoIncoming cells from the outside media to the
i/o port.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.7.1.3 |
dbCirEmIfStatsCellsDecodedHiOutgoing cells from the i/o port to the outside
media.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.7.1.4 |
dbCirEmIfStatsCellsDecodedLoOutgoing cells from the i/o port to the outside
media.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.7.1.5 |
dbCirEmIfStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.7.1.6 |
atmImaStatsTableTable of statistics for an atmIma interface. SEQUENCE OF AtmImaStatsEntry .1.3.6.1.4.1.1751.2.18.11.8 |
atmImaStatsEntryRow definition for the atmIma statistics
table. AtmImaStatsEntry .1.3.6.1.4.1.1751.2.18.11.8.1 |
atmImaStatsIdInterface index (SSPPCCC) to the atmIma
statistics table. IntfIndex .1.3.6.1.4.1.1751.2.18.11.8.1.1 |
atmImaStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.2 |
atmImaStatsImaViolationsICP violations: count of errored, invalid or missing ICP
cells during non-SES-IMA condition.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.3 |
atmImaStatsOifAnomaliesThe number of OIF anomalies during non-SES-IMA condition at
the near-end.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.4 |
atmImaStatsNeTxNumFailuresThe number of times a near-end transmit failure alarm
condition has been entered on this link.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.5 |
atmImaStatsNeRxNumFailuresThe number of times a near-end receive failure alarm
condition has been entered on this link (i.e., LIF, LODS,
Mis-Connected, RDI-IMA).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.6 |
atmImaStatsFeTxNumFailuresThe number of times a far-end transmit failure alarm
condition has been entered on this link.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.7 |
atmImaStatsFeRxNumFailuresThe number of times a far-end receive failure alarm condition
has been entered on this link (i.e. LIF, LODS, Mis-Connected,
RDI-IMA).ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.8 |
atmImaStatsTxStuffsCounts of stuff events inserted in the transmit direction.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.9 |
atmImaStatsRxStuffsCounts of stuff events detected in the receive direction.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.8.1.10 |
ilmiStatsTableTable of statistics for an ILMI enabled interface. SEQUENCE OF IlmiStatsEntry .1.3.6.1.4.1.1751.2.18.11.9 |
ilmiStatsEntryRow definition for the ILMI statistics table. IlmiStatsEntry .1.3.6.1.4.1.1751.2.18.11.9.1 |
ilmiStatsIdInterface index (SSPPCCC) for the ILMI interface. IntfIndex .1.3.6.1.4.1.1751.2.18.11.9.1.1 |
ilmiStatsTimerTime, in seconds, since last statistics reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.2 |
ilmiStatsLinkResetsTimes connectivity has toggled between down and
up.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.3 |
ilmiStatsAttachPtChangedTimes Attachment Point change was detected.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.4 |
ilmiStatsAttachPtVerifiedTimes Attachment Point was verified successfully.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.5 |
ilmiStatsSecureLnkProcInitTimes Secure Link Procedure was initiated.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.6 |
ilmiStatsColdStartRxTimes Cold Start trap was received.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.7 |
ilmiStatsColdStartTxTimes Cold Start trap was transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.8 |
ilmiStatsPduRxilmi pdu receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.9 |
ilmiStatsPduTxilmi pdu transmittedro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.10 |
ilmiStatsReqTimeoutsTimes getRequest of any type timed out.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.11 |
ilmiStatsPacketDiscTimes a received packet was discarded.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.9.1.12 |
viprStatsTableThe table which holds viprStatsEntry data. SEQUENCE OF ViprStatsEntry .1.3.6.1.4.1.1751.2.18.11.10 |
viprStatsEntryA table entry for VPN related statistics
information. ViprStatsEntry .1.3.6.1.4.1.1751.2.18.11.10.1 |
viprStatsResetA SNMP set action to reset VPN related
statistics info.rw Enumeration .1.3.6.1.4.1.1751.2.18.11.10.1.1 |
viprStatsPacketsRxHiGood packets received from the backplanero Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.2 |
viprStatsPacketsRxLoGood packets received from the backplanero Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.3 |
viprStatsPacketsTxHipackets transmitted to the backplanero Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.4 |
viprStatsPacketsTxLopackets transmitted to the backplanero Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.5 |
viprStatsMismatchCrcHipackets received has been dropped due to a mismached CRCro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.6 |
viprStatsMismatchCrcLopackets received has been dropped due to a mismached CRCro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.7 |
viprStatsInsufficientPcktsHipacket received length is greater than the number of cells receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.8 |
viprStatsInsufficientPcktsLopacket received length is greater than the number of cells receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.9 |
viprStatsExceedAal5CellsHinumber of cells received is greater than the actual length of the aal5ro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.10 |
viprStatsExceedAal5CellsLonumber of cells received is greater than the actual length of the aal5ro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.11 |
viprStatsPrototypeErrorsHiunrecognized encapsulation typero Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.12 |
viprStatsPrototypeErrorsLounrecognized encapsulation typero Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.13 |
viprStatsArpProtoRxHiARP receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.14 |
viprStatsArpProtoRxLoARP receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.15 |
viprStatsIPInHdrErrorsHiIP packeted received has a bad headerro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.16 |
viprStatsIPInHdrErrorsLoIP packeted received has a bad headerro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.17 |
viprStatsIPInAddrErrorsHiIP packeted received has a bad IP Addressro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.18 |
viprStatsIPInAddrErrorsLoIP packeted received has a bad IP Addressro Integer32 .1.3.6.1.4.1.1751.2.18.11.10.1.19 |
virtualIntfStatsTableTable of Virtual Interfaces Configurations SEQUENCE OF VirtualIntfStatsEntry .1.3.6.1.4.1.1751.2.18.11.11 |
virtualIntfStatsEntryIndex is the Interface and the Virutal Interface VirtualIntfStatsEntry .1.3.6.1.4.1.1751.2.18.11.11.1 |
virtualIntfStatsIfInterface index for side A of an ATM-to-ATM PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.11.11.1.1 |
virtualIntfStatsViVI value. Def Val is 1 because 0 cannot be
configured INTEGER .1.3.6.1.4.1.1751.2.18.11.11.1.2 |
virtualIntfStatsEgrCellCountEgress Cell Count on VIro Integer32 .1.3.6.1.4.1.1751.2.18.11.11.1.3 |
virtualIntfStatsTimerTime, in seconds, since last reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.11.1.4 |
virtualIntfStatsResetstats reset field.rw Enumeration .1.3.6.1.4.1.1751.2.18.11.11.1.5 |
vuniIlmiStatsTableTable of statistics for an ILMI enabled interface. SEQUENCE OF VuniIlmiStatsEntry .1.3.6.1.4.1.1751.2.18.11.12 |
vuniIlmiStatsEntryRow definition for the ILMI statistics table. VuniIlmiStatsEntry .1.3.6.1.4.1.1751.2.18.11.12.1 |
vuniIlmiStatsIdInterface index (SSPPCCC) for the ILMI interface. IntfIndex .1.3.6.1.4.1.1751.2.18.11.12.1.1 |
vuniIlmiVUNIIdVirtual UNI number, second index to access the ILMI on
virtual UNI interface. INTEGER .1.3.6.1.4.1.1751.2.18.11.12.1.2 |
vuniIlmiStatsTimerTime, in seconds, since last statistics reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.3 |
vuniIlmiStatsLinkResetsTimes connectivity has toggled between down and
up.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.4 |
vuniIlmiStatsAttachPtChangedTimes Attachment Point change was detected.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.5 |
vuniIlmiStatsAttachPtVerifiedTimes Attachment Point was verified successfully.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.6 |
vuniIlmiStatsSecureLnkProcInitTimes Secure Link Procedure was initiated.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.7 |
vuniIlmiStatsColdStartRxTimes Cold Start trap was received.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.8 |
vuniIlmiStatsColdStartTxTimes Cold Start trap was transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.9 |
vuniIlmiStatsPduRxvuniIlmi pdu receivedro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.10 |
vuniIlmiStatsPduTxvuniIlmi pdu transmittedro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.11 |
vuniIlmiStatsReqTimeoutsTimes getRequest of any type timed out.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.12 |
vuniIlmiStatsPacketDiscTimes a received packet was discarded.ro Integer32 .1.3.6.1.4.1.1751.2.18.11.12.1.13 |
vuniResetIlmiStatisticsReset the ATM ILMI statistics counters for
the given channel Id (SSPPCCC) and vuni Idrw Enumeration .1.3.6.1.4.1.1751.2.18.11.12.1.14 |
connectionStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.12 |
atmPvcVccStatsTableTable of statistics for a channel connection SEQUENCE OF AtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.1 |
atmPvcVccStatsEntryRow definition for the connection statistics
table AtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.1.1 |
atmPvcVccStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.1.1.1 |
atmPvcVccStatsVpiAVPI on side A INTEGER .1.3.6.1.4.1.1751.2.18.12.1.1.2 |
atmPvcVccStatsVciAVCI on side A INTEGER .1.3.6.1.4.1.1751.2.18.12.1.1.3 |
atmPvcVccStatsIfBInterface index (SSPPCCC) on side B IntfIndex .1.3.6.1.4.1.1751.2.18.12.1.1.4 |
atmPvcVccStatsVpiBVPI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.1.1.5 |
atmPvcVccStatsVciBVCI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.1.1.6 |
atmPvcVccStatsInCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.7 |
atmPvcVccStatsInCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.8 |
atmPvcVccStatsOutCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.9 |
atmPvcVccStatsOutCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.10 |
atmPvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.11 |
atmPvcVccStatsInCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.12 |
atmPvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.13 |
atmPvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.14 |
atmPvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.15 |
atmPvcVccStatsFrwdErrCrrctnRateA2BDisplays the Forward error correction rate being
used by the FEC module in the A2B direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.12.1.1.16 |
atmPvcVccStatsFrwdErrCrrctnRateB2ADisplays the Forward error correction rate being
used by the FEC module in the B2A direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.12.1.1.17 |
atmPvcVccStatsInOdometerCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.18 |
atmPvcVccStatsInOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.19 |
atmPvcVccStatsOutOdometerCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.20 |
atmPvcVccStatsOutOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.21 |
atmPvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.22 |
atmPvcVccStatsInOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.23 |
atmPvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.24 |
atmPvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.25 |
atmPvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.26 |
atmPvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.1.1.27 |
atmPvcVccStatsOamAisTxANumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.28 |
atmPvcVccStatsOamAisRxANumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.29 |
atmPvcVccStatsOamRdiTxANumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.30 |
atmPvcVccStatsOamRdiRxANumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.31 |
atmPvcVccStatsOamAisTxBNumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.32 |
atmPvcVccStatsOamAisRxBNumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.33 |
atmPvcVccStatsOamRdiTxBNumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.34 |
atmPvcVccStatsOamRdiRxBNumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.35 |
atmPvcVccStatsCellsDroppedACells Dropped on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.36 |
atmPvcVccStatsCellsTaggedACells Tagged on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.37 |
atmPvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.38 |
atmPvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.1.1.39 |
atmPvcVpcStatsTableTable of statistics for a channel connection SEQUENCE OF AtmPvcVpcStatsEntry .1.3.6.1.4.1.1751.2.18.12.2 |
atmPvcVpcStatsEntryRow definition for the connection statistics
table AtmPvcVpcStatsEntry .1.3.6.1.4.1.1751.2.18.12.2.1 |
atmPvcVpcStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.2.1.1 |
atmPvcVpcStatsVpiAVPI on side A INTEGER .1.3.6.1.4.1.1751.2.18.12.2.1.2 |
atmPvcVpcStatsIfBInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.2.1.3 |
atmPvcVpcStatsVpiBVPI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.2.1.4 |
atmPvcVpcStatsInCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.5 |
atmPvcVpcStatsInCellCountLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.6 |
atmPvcVpcStatsOutCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.7 |
atmPvcVpcStatsOutCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.8 |
atmPvcVpcStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.9 |
atmPvcVpcStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.10 |
atmPvcVpcStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.11 |
atmPvcVpcStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.12 |
atmPvcVpcStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.13 |
atmPvcVpcStatsInOdometerCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.14 |
atmPvcVpcStatsInOdometerCellCountLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.15 |
atmPvcVpcStatsOutOdometerCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.16 |
atmPvcVpcStatsOutOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.17 |
atmPvcVpcStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.18 |
atmPvcVpcStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.19 |
atmPvcVpcStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.20 |
atmPvcVpcStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.21 |
atmPvcVpcStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.22 |
atmPvcVpcStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.2.1.23 |
atmPvcVpcStatsOamAisTxANumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.24 |
atmPvcVpcStatsOamAisRxANumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.25 |
atmPvcVpcStatsOamRdiTxANumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.26 |
atmPvcVpcStatsOamRdiRxANumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.27 |
atmPvcVpcStatsOamAisTxBNumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.28 |
atmPvcVpcStatsOamAisRxBNumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.29 |
atmPvcVpcStatsOamRdiTxBNumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.30 |
atmPvcVpcStatsOamRdiRxBNumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.31 |
atmPvcVpcStatsCellsDroppedACells Dropped on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.32 |
atmPvcVpcStatsCellsTaggedACells Tagged on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.33 |
atmPvcVpcStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.34 |
atmPvcVpcStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.2.1.35 |
atmSvcVccStatsTableTable of statistics for a channel connection SEQUENCE OF AtmSvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.3 |
atmSvcVccStatsEntryRow definition for the connection statistics
table AtmSvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.3.1 |
atmSvcVccStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.3.1.1 |
atmSvcVccStatsVpiAVPI on side A INTEGER .1.3.6.1.4.1.1751.2.18.12.3.1.2 |
atmSvcVccStatsVciAVCI on side A INTEGER .1.3.6.1.4.1.1751.2.18.12.3.1.3 |
atmSvcVccStatsIfBInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.3.1.4 |
atmSvcVccStatsVpiBVPI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.3.1.5 |
atmSvcVccStatsVciBVCI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.3.1.6 |
atmSvcVccStatsInCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.7 |
atmSvcVccStatsInCellCountLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.8 |
atmSvcVccStatsOutCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.9 |
atmSvcVccStatsOutCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.10 |
atmSvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.11 |
atmSvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.12 |
atmSvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.13 |
atmSvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.14 |
atmSvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.15 |
atmSvcVccStatsInOdometerCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.16 |
atmSvcVccStatsInOdometerCellCountLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.17 |
atmSvcVccStatsOutOdometerCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.18 |
atmSvcVccStatsOutOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.19 |
atmSvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.20 |
atmSvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.21 |
atmSvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.22 |
atmSvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.23 |
atmSvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.24 |
atmSvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.3.1.25 |
atmSvcVccStatsCellsDroppedACells Dropped on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.26 |
atmSvcVccStatsCellsTaggedACells Tagged on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.27 |
atmSvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.28 |
atmSvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.3.1.29 |
ipAtmAppPvcVccStatsTableTable of Statistics entries SEQUENCE OF IpAtmAppPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.4 |
ipAtmAppPvcVccStatsEntryRow definition for statistics attribution. IpAtmAppPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.4.1 |
ipAtmAppPvcVccStatsDestAddrAStatistics destination IP address IpAddress .1.3.6.1.4.1.1751.2.18.12.4.1.1 |
ipAtmAppPvcVccStatsSubnetMaskAThe subnet mask of the destination IP address.
Value is an IP address. IpAddress .1.3.6.1.4.1.1751.2.18.12.4.1.2 |
ipAtmAppPvcVccStatsIfBInterface index (SSPPCCC) on side B IntfIndex .1.3.6.1.4.1.1751.2.18.12.4.1.3 |
ipAtmAppPvcVccStatsVpiBVPI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.4.1.4 |
ipAtmAppPvcVccStatsVciBVCI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.4.1.5 |
ipAtmAppPvcVccStatsInCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.6 |
ipAtmAppPvcVccStatsInCellCountLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.7 |
ipAtmAppPvcVccStatsOutCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.8 |
ipAtmAppPvcVccStatsOutCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.9 |
ipAtmAppPvcVccStatsFramesInBnumber of frames received on side B.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.10 |
ipAtmAppPvcVccStatsFramesOutBnumber of frames sent from side B.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.11 |
ipAtmAppPvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.12 |
ipAtmAppPvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.13 |
ipAtmAppPvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.14 |
ipAtmAppPvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.15 |
ipAtmAppPvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.16 |
ipAtmAppPvcVccStatsInOdometerCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.17 |
ipAtmAppPvcVccStatsInOdometerCellCountLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.18 |
ipAtmAppPvcVccStatsOutOdometerCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.19 |
ipAtmAppPvcVccStatsOutOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.20 |
ipAtmAppPvcVccStatsOdometerFramesInBValid frames received at side B.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.21 |
ipAtmAppPvcVccStatsOdometerFramesOutBValid frames transmitted from side B.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.22 |
ipAtmAppPvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.23 |
ipAtmAppPvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.24 |
ipAtmAppPvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.25 |
ipAtmAppPvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.26 |
ipAtmAppPvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.27 |
ipAtmAppPvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.4.1.28 |
ipAtmAppPvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.29 |
ipAtmAppPvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.4.1.30 |
ipAtmAppSvcVccStatsTableTable of statistics entries SEQUENCE OF IpAtmAppSvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.5 |
ipAtmAppSvcVccStatsEntryRow definition of statistics attributes. IpAtmAppSvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.5.1 |
ipAtmAppSvcVccStatsDestAddrAStatistics destination IP address IpAddress .1.3.6.1.4.1.1751.2.18.12.5.1.1 |
ipAtmAppSvcVccStatsSubnetMaskAThe subnet mask of the destination IP address.
Value is an IP address. IpAddress .1.3.6.1.4.1.1751.2.18.12.5.1.2 |
ipAtmAppSvcVccStatsIfBInterface index (SSPPCCC) on side B IntfIndex .1.3.6.1.4.1.1751.2.18.12.5.1.3 |
ipAtmAppSvcVccStatsVpiBVPI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.5.1.4 |
ipAtmAppSvcVccStatsVciBVCI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.5.1.5 |
ipAtmAppSvcVccStatsInCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.6 |
ipAtmAppSvcVccStatsInCellCountLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.7 |
ipAtmAppSvcVccStatsOutCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.8 |
ipAtmAppSvcVccStatsOutCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.9 |
ipAtmAppSvcVccStatsFramesInBFrames received at side B.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.10 |
ipAtmAppSvcVccStatsFramesOutBFrames transmitted from side B.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.11 |
ipAtmAppSvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.12 |
ipAtmAppSvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.13 |
ipAtmAppSvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.14 |
ipAtmAppSvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.15 |
ipAtmAppSvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.16 |
ipAtmAppSvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.17 |
ipAtmAppSvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.5.1.18 |
cirEmAtmPvcVccStatsTableTable of statistics for a channel connection SEQUENCE OF CirEmAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.6 |
cirEmAtmPvcVccStatsEntryRow definition for the connection statistics
table CirEmAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.6.1 |
cirEmAtmPvcVccStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.6.1.1 |
cirEmAtmPvcVccStatsIfBInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.6.1.2 |
cirEmAtmPvcVccStatsVpiBVPI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.6.1.3 |
cirEmAtmPvcVccStatsVciBVCI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.6.1.4 |
cirEmAtmPvcVccStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.5 |
cirEmAtmPvcVccStatsCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.6 |
cirEmAtmPvcVccStatsCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.7 |
cirEmAtmPvcVccStatsCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.8 |
cirEmAtmPvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.9 |
cirEmAtmPvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.10 |
cirEmAtmPvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.11 |
cirEmAtmPvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.12 |
cirEmAtmPvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.13 |
cirEmAtmPvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.14 |
cirEmAtmPvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.15 |
cirEmAtmPvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.16 |
cirEmAtmPvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.17 |
cirEmAtmPvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.18 |
cirEmAtmPvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.19 |
cirEmAtmPvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.20 |
cirEmAtmPvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.21 |
cirEmAtmPvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.22 |
cirEmAtmPvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.6.1.23 |
cirEmAtmPvcVccStatsOamAisTxNumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.24 |
cirEmAtmPvcVccStatsOamAisRxNumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.25 |
cirEmAtmPvcVccStatsOamRdiTxNumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.26 |
cirEmAtmPvcVccStatsOamRdiRxNumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.27 |
cirEmAtmPvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.28 |
cirEmAtmPvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.6.1.29 |
frAtmPvcVccStatsTableTable of statistics for a channel connection SEQUENCE OF FrAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.7 |
frAtmPvcVccStatsEntryRow definition for the connection statistics
table FrAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.7.1 |
frAtmPvcVccStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.7.1.1 |
frAtmPvcVccStatsDlciAdlci - side A INTEGER .1.3.6.1.4.1.1751.2.18.12.7.1.2 |
frAtmPvcVccStatsIfBInterface index (SSPPCCC) on side B IntfIndex .1.3.6.1.4.1.1751.2.18.12.7.1.3 |
frAtmPvcVccStatsVpiBVPI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.7.1.4 |
frAtmPvcVccStatsVciBVCI on side B INTEGER .1.3.6.1.4.1.1751.2.18.12.7.1.5 |
frAtmPvcVccStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.6 |
frAtmPvcVccStatsCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.7 |
frAtmPvcVccStatsCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.8 |
frAtmPvcVccStatsCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.9 |
frAtmPvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.10 |
frAtmPvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.11 |
frAtmPvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.12 |
frAtmPvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.13 |
frAtmPvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.14 |
frAtmPvcVccStatsFramesDroppedANumber of frames dropped for a given DLCI for A2B
direction, only applicable to the input side.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.15 |
frAtmPvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.16 |
frAtmPvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.17 |
frAtmPvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.18 |
frAtmPvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.19 |
frAtmPvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.20 |
frAtmPvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.21 |
frAtmPvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.22 |
frAtmPvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.23 |
frAtmPvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.24 |
frAtmPvcVccStatsOdometerFramesDroppedANumber of frames dropped for a given DLCI for A2B
direction, only applicable to the input side.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.25 |
frAtmPvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.7.1.26 |
frAtmPvcVccStatsOamAisTxNumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.27 |
frAtmPvcVccStatsOamAisRxNumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.28 |
frAtmPvcVccStatsOamRdiTxNumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.29 |
frAtmPvcVccStatsOamRdiRxNumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.30 |
frAtmPvcVccStatsAal5ErrFramesANumber of Aal5 Errored Frames, which are not
dropped due to UPC in A2B dir,
only applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.31 |
frAtmPvcVccStatsFramesTaggedANumber of Frames tagged due to UPC in A2B
dir, only applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.32 |
frAtmPvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.33 |
frAtmPvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.7.1.34 |
frFrPvcStatsTableTable of statistics for a channel connection SEQUENCE OF FrFrPvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.8 |
frFrPvcStatsEntryRow definition for the connection statistics
table FrFrPvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.8.1 |
frFrPvcStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.8.1.1 |
frFrPvcStatsDlciAdlci - side A INTEGER .1.3.6.1.4.1.1751.2.18.12.8.1.2 |
frFrPvcStatsIfBInterface index (SSPPCCC) on side B IntfIndex .1.3.6.1.4.1.1751.2.18.12.8.1.3 |
frFrPvcStatsDlciBdlci - side B INTEGER .1.3.6.1.4.1.1751.2.18.12.8.1.4 |
frFrPvcStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.5 |
frFrPvcStatsCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.6 |
frFrPvcStatsCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.7 |
frFrPvcStatsCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.8 |
frFrPvcStatsCellsEncodedHiBCells encoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.9 |
frFrPvcStatsCellsEncodedLoBCells encoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.10 |
frFrPvcStatsCellsDecodedHiBCells decoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.11 |
frFrPvcStatsCellsDecodedLoBCells decoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.12 |
frFrPvcStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.13 |
frFrPvcStatsFramesDroppedANumber of frames dropped for a given DLCI for A2B
direction, only applicable to the input side.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.14 |
frFrPvcStatsFramesDroppedBNumber of frames dropped for a given DLCI for B2A
direction, only applicable to the input side.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.15 |
frFrPvcStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.16 |
frFrPvcStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.17 |
frFrPvcStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.18 |
frFrPvcStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.19 |
frFrPvcStatsOdometerCellsEncodedHiBCells encoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.20 |
frFrPvcStatsOdometerCellsEncodedLoBCells encoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.21 |
frFrPvcStatsOdometerCellsDecodedHiBCells decoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.22 |
frFrPvcStatsOdometerCellsDecodedLoBCells decoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.23 |
frFrPvcStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.24 |
frFrPvcStatsOdometerFramesDroppedANumber of frames dropped for a given DLCI for A2B
direction, only applicable to the input side.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.25 |
frFrPvcStatsOdometerFramesDroppedBNumber of frames dropped for a given DLCI for B2A
direction, only applicable to the input side.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.26 |
frFrPvcStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.8.1.27 |
frFrPvcStatsAal5ErrFramesANumber of Aal5 Errored Frames, which are not
dropped due to UPC in A2B dir, only
applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.28 |
frFrPvcStatsAal5ErrFramesBNumber of Aal5 Errored Frames, which are not
dropped due to UPC in B2A dir,
only applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.29 |
frFrPvcStatsFramesTaggedANumber of Frames tagged due to UPC in A2B
dir, only applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.30 |
frFrPvcStatsFramesTaggedBNumber of Frames tagged due to UPC in B2A
dir, only applicable to Input Sidero Integer32 .1.3.6.1.4.1.1751.2.18.12.8.1.31 |
vbrAtmPvcVccStatsTableTable of statistics for a channel connection SEQUENCE OF VbrAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.9 |
vbrAtmPvcVccStatsEntryRow definition for the connection statistics
table VbrAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.9.1 |
vbrAtmPvcVccStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.9.1.1 |
vbrAtmPvcVccStatsIfBInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.9.1.2 |
vbrAtmPvcVccStatsVpiBvpi - side B INTEGER .1.3.6.1.4.1.1751.2.18.12.9.1.3 |
vbrAtmPvcVccStatsVciBvci - side B INTEGER .1.3.6.1.4.1.1751.2.18.12.9.1.4 |
vbrAtmPvcVccStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.5 |
vbrAtmPvcVccStatsCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.6 |
vbrAtmPvcVccStatsCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.7 |
vbrAtmPvcVccStatsCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.8 |
vbrAtmPvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.10 |
vbrAtmPvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.11 |
vbrAtmPvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.12 |
vbrAtmPvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.13 |
vbrAtmPvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.14 |
vbrAtmPvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.15 |
vbrAtmPvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.16 |
vbrAtmPvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.17 |
vbrAtmPvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.18 |
vbrAtmPvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.19 |
vbrAtmPvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.20 |
vbrAtmPvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.21 |
vbrAtmPvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.22 |
vbrAtmPvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.23 |
vbrAtmPvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.9.1.24 |
vbrAtmPvcVccStatsOamAisTxNumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.25 |
vbrAtmPvcVccStatsOamAisRxNumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.26 |
vbrAtmPvcVccStatsOamRdiTxNumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.27 |
vbrAtmPvcVccStatsOamRdiRxNumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.28 |
vbrAtmPvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.29 |
vbrAtmPvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.9.1.30 |
cirEmCirEmPvcStatsTableTable of statistics for a channel connection SEQUENCE OF CirEmCirEmPvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.10 |
cirEmCirEmPvcStatsEntryRow definition for the connection statistics
table CirEmCirEmPvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.10.1 |
cirEmCirEmPvcStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.10.1.1 |
cirEmCirEmPvcStatsIfBInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.10.1.2 |
cirEmCirEmPvcStatsCellsEncodedHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.3 |
cirEmCirEmPvcStatsCellsEncodedLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.4 |
cirEmCirEmPvcStatsCellsDecodedHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.5 |
cirEmCirEmPvcStatsCellsDecodedLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.6 |
cirEmCirEmPvcStatsCellsEncodedHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.7 |
cirEmCirEmPvcStatsCellsEncodedLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.8 |
cirEmCirEmPvcStatsCellsDecodedHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.9 |
cirEmCirEmPvcStatsCellsDecodedLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.10 |
cirEmCirEmPvcStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.11 |
cirEmCirEmPvcStatsOdometerCellsEncodedHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.12 |
cirEmCirEmPvcStatsOdometerCellsEncodedLoAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.13 |
cirEmCirEmPvcStatsOdometerCellsDecodedHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.14 |
cirEmCirEmPvcStatsOdometerCellsDecodedLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.15 |
cirEmCirEmPvcStatsOdometerCellsEncodedHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.16 |
cirEmCirEmPvcStatsOdometerCellsEncodedLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.17 |
cirEmCirEmPvcStatsOdometerCellsDecodedHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.18 |
cirEmCirEmPvcStatsOdometerCellsDecodedLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.19 |
cirEmCirEmPvcStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.10.1.20 |
cirEmCirEmPvcStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.10.1.21 |
vbrVbrPvcStatsTableTable of statistics for a channel connection SEQUENCE OF VbrVbrPvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.11 |
vbrVbrPvcStatsEntryRow definition for the connection statistics
table VbrVbrPvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.11.1 |
vbrVbrPvcStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.11.1.1 |
vbrVbrPvcStatsIfBInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.11.1.2 |
vbrVbrPvcStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.4 |
vbrVbrPvcStatsCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.5 |
vbrVbrPvcStatsCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.6 |
vbrVbrPvcStatsCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.7 |
vbrVbrPvcStatsCellsEncodedHiBCells encoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.9 |
vbrVbrPvcStatsCellsEncodedLoBCells encoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.10 |
vbrVbrPvcStatsCellsDecodedHiBCells decoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.11 |
vbrVbrPvcStatsCellsDecodedLoBCells decoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.12 |
vbrVbrPvcStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.13 |
vbrVbrPvcStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.14 |
vbrVbrPvcStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.15 |
vbrVbrPvcStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.16 |
vbrVbrPvcStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.17 |
vbrVbrPvcStatsOdometerCellsEncodedHiBCells encoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.18 |
vbrVbrPvcStatsOdometerCellsEncodedLoBCells encoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.19 |
vbrVbrPvcStatsOdometerCellsDecodedHiBCells decoded on side B- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.20 |
vbrVbrPvcStatsOdometerCellsDecodedLoBCells decoded on side B- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.21 |
vbrVbrPvcStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.11.1.22 |
vbrVbrPvcStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.11.1.23 |
bridgeBridgePvcStatsTableTable of bridge-bridge PVC connection
statistics SEQUENCE OF BridgeBridgePvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.12 |
bridgeBridgePvcStatsEntryRow definition of statistics attributes BridgeBridgePvcStatsEntry .1.3.6.1.4.1.1751.2.18.12.12.1 |
bridgeBridgePvcStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.12.1.1 |
bridgeBridgePvcStatsIfBInterface index (SSPPCCC) on side B IntfIndex .1.3.6.1.4.1.1751.2.18.12.12.1.2 |
bridgeBridgePvcStatsCellsEncodedHiACells encoded on side A - (High order portion )ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.3 |
bridgeBridgePvcStatsCellsEncodedLoACells encoded on side A - ( Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.4 |
bridgeBridgePvcStatsCellsDecodedHiACells decoded on side A - ( High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.5 |
bridgeBridgePvcStatsCellsDecodedLoACells decoded on side A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.6 |
bridgeBridgePvcStatsCellsEncodedHiBCells encoded on side B - (High order portion )ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.7 |
bridgeBridgePvcStatsCellsEncodedLoBCells encoded on side B - (Low order portion )ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.8 |
bridgeBridgePvcStatsCellsDecodedHiBCells decoded on side B - (High order portion )ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.9 |
bridgeBridgePvcStatsCellsDecodedLoBCells decoded on side B -(Low order portion )ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.10 |
bridgeBridgePvcStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.11 |
bridgeBridgePvcStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.12 |
bridgeBridgePvcStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.13 |
bridgeBridgePvcStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.14 |
bridgeBridgePvcStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.15 |
bridgeBridgePvcStatsOdometerCellsEncodedHiBCells encoded on side B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.16 |
bridgeBridgePvcStatsOdometerCellsEncodedLoBCells encoded on side B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.17 |
bridgeBridgePvcStatsOdometerCellsDecodedHiBCells decoded on side B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.18 |
bridgeBridgePvcStatsOdometerCellsDecodedLoBCells decoded on side B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.19 |
bridgeBridgePvcStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.12.1.20 |
bridgeBridgePvcStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.12.1.21 |
bridgeAtmPvcVccStatsTableTable of statisics SEQUENCE OF BridgeAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.13 |
bridgeAtmPvcVccStatsEntryRow definition for the connection statistics
table BridgeAtmPvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.13.1 |
bridgeAtmPvcVccStatsIfAInterface index (SSPPCCC) on side A IntfIndex .1.3.6.1.4.1.1751.2.18.12.13.1.1 |
bridgeAtmPvcVccStatsIfBInterface index (SSPPCCC) on side B IntfIndex .1.3.6.1.4.1.1751.2.18.12.13.1.2 |
bridgeAtmPvcVccStatsVpiBvpi - side B INTEGER .1.3.6.1.4.1.1751.2.18.12.13.1.3 |
bridgeAtmPvcVccStatsVciBvci - side B INTEGER .1.3.6.1.4.1.1751.2.18.12.13.1.4 |
bridgeAtmPvcVccStatsCellsEncodedHiAnumber of cells encoded on side A
- (High order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.5 |
bridgeAtmPvcVccStatsCellsEncodedLoAnumber of cells encoded on side A
- (Low order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.6 |
bridgeAtmPvcVccStatsCellsDecodedHiAnumber of cells decoded on side A
- (High order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.7 |
bridgeAtmPvcVccStatsCellsDecodedLoAnumber of cells decoded on side A
- (Low order portion).ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.8 |
bridgeAtmPvcVccStatsInCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.9 |
bridgeAtmPvcVccStatsInCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.10 |
bridgeAtmPvcVccStatsOutCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.11 |
bridgeAtmPvcVccStatsOutCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.12 |
bridgeAtmPvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.13 |
bridgeAtmPvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.14 |
bridgeAtmPvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.15 |
bridgeAtmPvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.16 |
bridgeAtmPvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.17 |
bridgeAtmPvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.18 |
bridgeAtmPvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.19 |
bridgeAtmPvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.20 |
bridgeAtmPvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.21 |
bridgeAtmPvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.22 |
bridgeAtmPvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.13.1.23 |
bridgeAtmPvcVccStatsOamAisTxNumber of AIS cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.24 |
bridgeAtmPvcVccStatsOamAisRxNumber of AIS cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.25 |
bridgeAtmPvcVccStatsOamRdiTxNumber of RDI cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.26 |
bridgeAtmPvcVccStatsOamRdiRxNumber of RDI cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.27 |
bridgeAtmPvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.28 |
bridgeAtmPvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.13.1.29 |
cirEmAtmSpvcVccStatsTableTable of statistics for a CES SPVC channel
connection SEQUENCE OF CirEmAtmSpvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.14 |
cirEmAtmSpvcVccStatsEntryRow definition for the CES SPVC connection
statistics table CirEmAtmSpvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.14.1 |
cirEmAtmSpvcVccStatsIfAInterface index for side A, the circuit emulation
side, of a circuit emulation-atm SPVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.12.14.1.1 |
cirEmAtmSpvcVccStatsIfBInterface index for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.12.14.1.2 |
cirEmAtmSpvcVccStatsVpiBVPI value for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Valid
range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.12.14.1.3 |
cirEmAtmSpvcVccStatsVciBVCI value for side B, the atm side, of a
circuit emulation-atm SPVC VCC connection. Valid
range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.12.14.1.4 |
cirEmAtmSpvcVccStatsCellsEncodedHiACells encoded on side A - (High order portion )ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.5 |
cirEmAtmSpvcVccStatsCellsEncodedLoACells encoded on side A - ( Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.6 |
cirEmAtmSpvcVccStatsCellsDecodedHiACells decoded on side A - ( High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.7 |
cirEmAtmSpvcVccStatsCellsDecodedLoACells decoded on side A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.8 |
cirEmAtmSpvcVccStatsInCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.9 |
cirEmAtmSpvcVccStatsInCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.10 |
cirEmAtmSpvcVccStatsOutCellCountHiBValid cells transmitted on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.11 |
cirEmAtmSpvcVccStatsOutCellCountLoBValid cells transmitted on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.12 |
cirEmAtmSpvcVccStatsTimerNumber of seconds since stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.13 |
cirEmAtmSpvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.14 |
cirEmAtmSpvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.15 |
cirEmAtmSpvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.16 |
cirEmAtmSpvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.17 |
cirEmAtmSpvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.18 |
cirEmAtmSpvcVccStatsInOdometerCellCountLoBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.19 |
cirEmAtmSpvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.20 |
cirEmAtmSpvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.21 |
cirEmAtmSpvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.22 |
cirEmAtmSpvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.14.1.23 |
cirEmAtmSpvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.24 |
cirEmAtmSpvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.14.1.25 |
vbrAtmSpvcVccStatsTableTable of statistics for a TE SPVC channel
connection. SEQUENCE OF VbrAtmSpvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.15 |
vbrAtmSpvcVccStatsEntryRow definition for the TE SPVC connection
statistics table. VbrAtmSpvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.15.1 |
vbrAtmSpvcVccStatsIfAInterface index for side A, the variable bit rate
side, of a variable bit rate-atm SPVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.12.15.1.1 |
vbrAtmSpvcVccStatsIfBInterface index for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Number
value is interpreted as an interface of the form,
SSPPCCC, where SS is the card slot, PP is the port
number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.12.15.1.2 |
vbrAtmSpvcVccStatsVpiBVPI value for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Valid
range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.12.15.1.3 |
vbrAtmSpvcVccStatsVciBVCI value for side B, the atm side, of a
variable bit rate-atm SPVC VCC connection. Valid
range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.12.15.1.4 |
vbrAtmSpvcVccStatsCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.5 |
vbrAtmSpvcVccStatsCellsEncodedLoAells encoded on side A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.6 |
vbrAtmSpvcVccStatsCellsDecodedHiACells decoded on side A - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.7 |
vbrAtmSpvcVccStatsCellsDecodedLoACells decoded on side A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.8 |
vbrAtmSpvcVccStatsInCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.9 |
vbrAtmSpvcVccStatsInCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.10 |
vbrAtmSpvcVccStatsOutCellCountHiBValid cells transmitted on B -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.11 |
vbrAtmSpvcVccStatsOutCellCountLoBValid cells transmitted on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.12 |
vbrAtmSpvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.13 |
vbrAtmSpvcVccStatsOdometerCellsEncodedHiACells encoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.14 |
vbrAtmSpvcVccStatsOdometerCellsEncodedLoACells encoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.15 |
vbrAtmSpvcVccStatsOdometerCellsDecodedHiACells decoded on side A- (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.16 |
vbrAtmSpvcVccStatsOdometerCellsDecodedLoACells decoded on side A- (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.17 |
vbrAtmSpvcVccStatsInOdometerCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.18 |
vbrAtmSpvcVccStatsInOdometerCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.19 |
vbrAtmSpvcVccStatsOutOdometerCellCountHiBValid Cells transmitted on B -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.20 |
vbrAtmSpvcVccStatsOutOdometerCellCountLoBValid Cells transmitted on B -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.21 |
vbrAtmSpvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.22 |
vbrAtmSpvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.15.1.23 |
vbrAtmSpvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.24 |
vbrAtmSpvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.15.1.25 |
atmSpvcVccStatsTableTable of statistics for a ATM SPVC channel
connection SEQUENCE OF AtmSpvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.16 |
atmSpvcVccStatsEntryRow definition for the ATM SPVC connection
statistics table AtmSpvcVccStatsEntry .1.3.6.1.4.1.1751.2.18.12.16.1 |
atmSpvcVccStatsIfAInterface index for side A of an ATM-to-ATM PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.12.16.1.1 |
atmSpvcVccStatsVpiAVPI value for side A of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
4095. INTEGER .1.3.6.1.4.1.1751.2.18.12.16.1.2 |
atmSpvcVccStatsVciAVCI value for side A of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
65535. INTEGER .1.3.6.1.4.1.1751.2.18.12.16.1.3 |
atmSpvcVccStatsIfBInterface index for side B of an ATM-to-ATM PVC VCC
connection. Number value is interpreted as an
interface of the form, SSPPCCC, where SS is the
card slot, PP is the port number, and CCC is the
channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.12.16.1.4 |
atmSpvcVccStatsVpiBVPI value for side B of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
4095. INTEGER .1.3.6.1.4.1.1751.2.18.12.16.1.5 |
atmSpvcVccStatsVciBVCI value for side B of an ATM-to-ATM PVC VCC
connection. Valid range is a number between 0 and
65535. INTEGER .1.3.6.1.4.1.1751.2.18.12.16.1.6 |
atmSpvcVccStatsInCellCountHiAValid Cells received on A - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.7 |
atmSpvcVccStatsInCellCountLoAValid Cells received on A - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.8 |
atmSpvcVccStatsOutCellCountHiAValid cells transmitted on A -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.9 |
atmSpvcVccStatsOutCellCountLoAValid cells transmitted on A -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.10 |
atmSpvcVccStatsInCellCountHiBValid Cells received on B - (High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.11 |
atmSpvcVccStatsInCellCountLoBValid Cells received on B - (Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.12 |
atmSpvcVccStatsOutCellCountHiBValid cells transmitted on B -(High order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.13 |
atmSpvcVccStatsOutCellCountLoBValid cells transmitted on B -(Low order portion)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.14 |
atmSpvcVccStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.15 |
atmSpvcVccStatsFrwdErrCrrctnRateA2BDisplays the Forward error correction rate being
used by the FEC module in the A2B direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.12.16.1.16 |
atmSpvcVccStatsFrwdErrCrrctnRateB2ADisplays the Forward error correction rate being
used by the FEC module in the B2A direction. This
field is dynamic when Auto rates are selected. In
other cases, it will display the rate set by the
user.ro Enumeration .1.3.6.1.4.1.1751.2.18.12.16.1.17 |
atmSpvcVccStatsInOdometerCellCountHiAValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.18 |
atmSpvcVccStatsInOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.19 |
atmSpvcVccStatsOutOdometerCellCountHiAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.20 |
atmSpvcVccStatsOutOdometerCellCountLoAValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.21 |
atmSpvcVccStatsInOdometerCellCountHiBValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.22 |
atmSpvcVccStatsInOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.23 |
atmSpvcVccStatsOutOdometerCellCountHiBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.24 |
atmSpvcVccStatsOutOdometerCellCountLoBValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.25 |
atmSpvcVccStatsOdometerTimerNumber of seconds since odometer was reset.ro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.26 |
atmSpvcVccStatsOdometerResetOdometer reset button.rw Enumeration .1.3.6.1.4.1.1751.2.18.12.16.1.27 |
atmSpvcVccStatsCellsDroppedACells Dropped on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.28 |
atmSpvcVccStatsCellsTaggedACells Tagged on the Incoming side of Aro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.29 |
atmSpvcVccStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.30 |
atmSpvcVccStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.16.1.31 |
viprSubChnlStatsTableThe table which holds
viprSubChnlStatsEntry data. SEQUENCE OF ViprSubChnlStatsEntry .1.3.6.1.4.1.1751.2.18.12.17 |
viprSubChnlStatsEntryA table entry that contains IP interface
sub channel statistics. ViprSubChnlStatsEntry .1.3.6.1.4.1.1751.2.18.12.17.1 |
viprSubChnlStatsInCellCountHiAcells received on rt interface from another connro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.1 |
viprSubChnlStatsInCellCountLoAcells received on rt interface from another connro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.2 |
viprSubChnlStatsOutCellCountHiAcells sent out of a rt interface to another destro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.3 |
viprSubChnlStatsOutCellCountLoAcells sent out of a rt interface to another destro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.4 |
viprSubChnlStatsInCellCountHiBcells received on atm/fr/bridge
physical interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.5 |
viprSubChnlStatsInCellCountLoBcells received on atm/fr/bridge
physical interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.6 |
viprSubChnlStatsOutCellCountHiBcell transmitted out of a
physical atm/fr/bridge interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.7 |
viprSubChnlStatsOutCellCountLoBcell transmitted out of a
physical atm/fr/bridge interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.8 |
viprSubChnlStatsTimerNumber of seconds stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.9 |
viprSubChnlStatsInOdometerCellCountHiAodometer cells received on
rt interface from another connro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.10 |
viprSubChnlStatsInOdometerCellCountLoAodometer cells received on
rt interface from another connro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.11 |
viprSubChnlStatsOutOdometerCellCountHiAodometer cells sent out of a
rt interface to another destro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.12 |
viprSubChnlStatsOutOdometerCellCountLoAodometer cells sent out of a
rt interface to another destro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.13 |
viprSubChnlStatsInOdometerCellCountHiBodometer cells received on atm/fr/bridge
physical interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.14 |
viprSubChnlStatsInOdometerCellCountLoBodometer cells received on atm/fr/bridge
physical interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.15 |
viprSubChnlStatsOutOdometerCellCountHiBodometer cells transmitted out of a
physical atm/fr/bridge interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.16 |
viprSubChnlStatsOutOdometerCellCountLoBodometer cells transmitted out of a
physical atm/fr/bridge interfacero Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.17 |
viprSubChnlStatsOdometerTimerOdometer Number of seconds
stats have been collectingro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.18 |
viprSubChnlStatsOdometerResetto reset the subchannel statisticsrw Enumeration .1.3.6.1.4.1.1751.2.18.12.17.1.19 |
viprSubChnlStatsCellsDroppedBCells Dropped on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.20 |
viprSubChnlStatsCellsTaggedBCells Tagged on the Incoming side of Bro Integer32 .1.3.6.1.4.1.1751.2.18.12.17.1.21 |
ipAtmGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.13 |
ipAtmArpSrvConnTypetype of Arp Server connectionrw Enumeration .1.3.6.1.4.1.1751.2.18.13.1 |
ipAtmIpAddrLocal IP Addressrw IpAddress .1.3.6.1.4.1.1751.2.18.13.2 |
ipAtmIpMaskLocal IP Maskrw IpAddress .1.3.6.1.4.1.1751.2.18.13.3 |
atmArpTableARP Table SEQUENCE OF AtmArpEntry .1.3.6.1.4.1.1751.2.18.13.4 |
atmArpEntryARP Table entry AtmArpEntry .1.3.6.1.4.1.1751.2.18.13.4.1 |
atmArpIpAddressIP address of the IP host described in APR table
entry. IpAddress .1.3.6.1.4.1.1751.2.18.13.4.1.1 |
atmArpAtmAddressATM address of the IP host.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.13.4.1.2 |
atmArpAddrTypeType of ATM address value of atmArp address.rw Enumeration .1.3.6.1.4.1.1751.2.18.13.4.1.3 |
atmArpEntryStateState of this entry.ro Enumeration .1.3.6.1.4.1.1751.2.18.13.4.1.4 |
atmArpEntryRowStatusRowStatus of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.13.4.1.5 |
appIpRouteTableApplication IP Routing table. SEQUENCE OF AppIpRouteEntry .1.3.6.1.4.1.1751.2.18.13.5 |
appIpRouteEntryA route to a particular destination. AppIpRouteEntry .1.3.6.1.4.1.1751.2.18.13.5.1 |
appIpRouteDestThe destination IP address of this route. An
entry with a value of 0.0.0.0 is not valid
route. IpAddress .1.3.6.1.4.1.1751.2.18.13.5.1.1 |
appIpRouteMaskMask for Ip route, usefull only for SENS stack
VxWorks IpAddress .1.3.6.1.4.1.1751.2.18.13.5.1.2 |
appIpRouteMetric1The primary routing metric for this route. The
semantics of this metric are determined by the
routing-protocol specified in the routes
appIpRouteProto value. If this metric is not used,
its value should be set to 1. INTEGER .1.3.6.1.4.1.1751.2.18.13.5.1.3 |
appIpRouteNextHopThe IP address of the next hop of this route.
(In the case of a route bound to an interface
which is realized via a broadcast media, the value
of this field is the agent's IP address on that
interface.)rw IpAddress .1.3.6.1.4.1.1751.2.18.13.5.1.4 |
appIpRouteStateCurrent state of routero Enumeration .1.3.6.1.4.1.1751.2.18.13.5.1.5 |
iispRouting OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.14 |
iispCbrRoutTableIISP CBR Routing Table SEQUENCE OF IispCbrRoutEntry .1.3.6.1.4.1.1751.2.18.14.1 |
iispCbrRoutEntryIISP CBR Table Entry IispCbrRoutEntry .1.3.6.1.4.1.1751.2.18.14.1.1 |
iispCbrRoutLengthlength in bits Integer32 .1.3.6.1.4.1.1751.2.18.14.1.1.1 |
iispCbrRoutNsapAddrnsap address OCTET STRING .1.3.6.1.4.1.1751.2.18.14.1.1.2 |
iispCbrRoutIfIndexInterface index - SSPPCCCrw IntfIndex .1.3.6.1.4.1.1751.2.18.14.1.1.3 |
iispCbrRoutRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.14.1.1.4 |
iispVbrRoutTableIISP CBR Routing Table SEQUENCE OF IispVbrRoutEntry .1.3.6.1.4.1.1751.2.18.14.2 |
iispVbrRoutEntryIISP CBR Table Entry IispVbrRoutEntry .1.3.6.1.4.1.1751.2.18.14.2.1 |
iispVbrRoutLengthlength in bits Integer32 .1.3.6.1.4.1.1751.2.18.14.2.1.1 |
iispVbrRoutNsapAddrnsap address OCTET STRING .1.3.6.1.4.1.1751.2.18.14.2.1.2 |
iispVbrRoutIfIndexInterface index - SSPPCCCrw IntfIndex .1.3.6.1.4.1.1751.2.18.14.2.1.3 |
iispVbrRoutRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.14.2.1.4 |
iispCbrRouteTableIISP CBR Routing Table SEQUENCE OF IispCbrRouteEntry .1.3.6.1.4.1.1751.2.18.14.3 |
iispCbrRouteEntryIISP CBR Route Entry IispCbrRouteEntry .1.3.6.1.4.1.1751.2.18.14.3.1 |
iispCbrRouteLengthlength in bits Integer32 .1.3.6.1.4.1.1751.2.18.14.3.1.1 |
iispCbrRouteNsapAddrnsap address OCTET STRING .1.3.6.1.4.1.1751.2.18.14.3.1.2 |
iispCbrRouteIfIndexInterface index - SSPPCCC IntfIndex .1.3.6.1.4.1.1751.2.18.14.3.1.3 |
iispCbrRouteRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.14.3.1.4 |
iispCbrRouteIfVuniIdVirtual UNI interface VUNI Id INTEGER .1.3.6.1.4.1.1751.2.18.14.3.1.5 |
iispCbrRouteTypeType of Route, Categorisation of an Endpoint
Route or an intermediate Routerw Enumeration .1.3.6.1.4.1.1751.2.18.14.3.1.6 |
iispCbrRouteDestType of Destination, Categorisation of an
Endpoint destination or an intermediate
destinationrw Enumeration .1.3.6.1.4.1.1751.2.18.14.3.1.7 |
iispVbrRouteTableIISP CBR Routing Table SEQUENCE OF IispVbrRouteEntry .1.3.6.1.4.1.1751.2.18.14.4 |
iispVbrRouteEntryIISP CBR Table Entry IispVbrRouteEntry .1.3.6.1.4.1.1751.2.18.14.4.1 |
iispVbrRouteLengthlength in bits Integer32 .1.3.6.1.4.1.1751.2.18.14.4.1.1 |
iispVbrRouteNsapAddrnsap address OCTET STRING .1.3.6.1.4.1.1751.2.18.14.4.1.2 |
iispVbrRouteIfIndexIn most cases, it is the I/O Interface index -
SSPPCCC. However, in case of ATM Trunking's
Narrowband routing and Broadband routing, this
is either the CAS trunk group ID, or the remote
IWF ID, which are 1 to 3 digits decimal numbers IntfIndex .1.3.6.1.4.1.1751.2.18.14.4.1.3 |
iispVbrRouteRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.14.4.1.4 |
iispVbrRouteIfVuniIdVirtual UNI interface VUNI Id INTEGER .1.3.6.1.4.1.1751.2.18.14.4.1.5 |
iispVbrRouteTypeType of Route, Categorisation of an Endpoint
Route or an intermediate Routerw Enumeration .1.3.6.1.4.1.1751.2.18.14.4.1.6 |
iispVbrRouteDestType of Destination, Categorisation of an
Endpoint destination or an intermediate
destinationrw Enumeration .1.3.6.1.4.1.1751.2.18.14.4.1.7 |
returnCode OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.15 |
pvcFailureReasonCodeAn identified reason why an ATM PVC connection
request failed.
aal2CuTimerOutOfRange(298): this error code is
generated when the aal2CuTimer value is out
of range and the valid reanges is 0 to 8
(0 - 40 msec of delay).
unrecognizableDigitCollectTypeA2B(299):
unrecognizable digital tone set in
connection A2B direction.
unrecognizableDigitCollectTypeB2A(300):
unrecognizable digital tone set in
connection B2A direction.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.1 |
interfaceIndexInterface index used for identifcation in traps.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.ro IntfIndex .1.3.6.1.4.1.1751.2.18.15.2 |
interfaceTypeInterface type used for identification in traps.
A specific interface is associated with each
number.
atmUni3-0(1) ATM User Network Interface version 3.0
atmUni3-1(2) ATM User Network Interface version 3.1
iispUser(3) Interim Inter Switch Protocol User Side
iispNetwork(4) Interim Inter Switch Protocol Network
Side
circuitEmulation(5) ATM Circuit Emulation
frameRelayUni(6) Frame Relay User Network Interface
pri-isdn-user(7) Integrated Services Digital Network
Primary
Rate Interface User Interface
pri-isdn-network(8) Integrated Services Digital Network
Primary
Rate Interface Network Interface
terminalEmulation(9) Terminal Emulation
dsp(10) DSP
hdlcPassThrough(11) High Level Data Link Control Pass
Through Interface
bridge(12) Ethernet Bridge
routing(13) Ethernet Routing
dbCirEm(14) Dynamic Bandwidth Circuit Emulation
frameRelayNni(15) Frame Relay Network Network Interface
dsp2(16) DSP2
atmIma(17) ATM Inverse Multiplexing over ATM (IMA)
atmPnni1-0(18) ATM Private Network Network Interface
Version 1.0
atmUni4-0(19) ATM User Network Interface Version 4.0
atmVnnUni3-1(20) ATM Virtual Network Navigator User
Network Interface Version 3.1
casTrunkLine(21) Channel Associated Signaling Trunk
Line Interface
toneAnnce(22) Tone Announcement Interface
gr303(23) GR303ro Enumeration .1.3.6.1.4.1.1751.2.18.15.3 |
interfaceFailureReasonCodeIdentification of cause for failure in changing
the status of an interface.
interfaceInService(1)
Most, if not all, modifications require
that the interface be out of service.
interfaceNotNew(2)
Some modifications require that the
interface must never have been in service.
interfaceExists(3)
Some modifications, such as setting the
interface type, require that no interface
exists. (type must be unconfigured).
bridgeGroupActive(4)
For setting the bridgeDomainNumber in
bridge or router interfaces. to add an
interface to a bridgeGroup, the bridgeGroup
must be in service.
signalingNotEnabled(5)
For this interface to be created,
signaling must be enabled.
firmwareOutOfDate(6)
The firmware for the i/o card does not
work with this interface.
t1SigEnableInterfaceNotSupported(7)
The interface is not supported if T1 signaling is enabled
ts16ForData(8)
ts16 has been set for passing data and the
user attempts to turn on signaling.
dbcesConfigured(9)
Signaling cannot be disabled because this
interface is configured as dbces.
signalingEnabled(10)
Signaling is on for at least one of the
channels while trying to change e1 TS16
from CAS to CCS.
cmCardTypeNotSupported(11)
CM_NET interface is only supported by
DS3 DS1 OC3 and SUPER_DS1 cards
cmMultipleIntfNotSupported(12)
only one interface can be configured as CM_NET
cmIntfInService(13)
CM_NET interface is in-service
cmInterfaceConfigured(14)
CM_NET interface is configured
channelizationEnabled(15)
A port can not be channelized in order
to support unstructured CE.
unstructuredCEConfigured(16)
A port which has been channelized can not
be configured to support unstructured CE.
firmwareOutOfDate-ts16CAS-unsupported(17)
ts16CAS is not supported by the firmware
firmwareOutOfDate-interfaceType-unsupported(18)
interface type is not supported by the firmware
firmwareOutOfDate-ts16-unsupported(19)
ts16 is not supported by the firmware
invalidPortMap(20)
invalid port map
otherInterfacesExistOnThisPort(21)
ISDN interface needs all 24 channels on the port. If
any of the channels on that interface are already configured,
the ISDN interface can not be defined on that port.
intfInIMAgroup(22)
chanId bit in portMap is 1
errorCTC-portTxClkSrc-notLocal(23)
if imaGrpChannelNeTxClkMode is set to ctc then all ports
should have the transmitClockSource as localTiming
different-LoopbackConfig-on-Ports(24)
all physical ports included in the portMap
must have the same loopback configuration
imaGChanNeTxClkMode-unsupported(25)
ima group channel near-end Tx clock mode is not supported
intfChange-Disallowed-on-APS-ProtectionPort(26)
an interface cannot be manipulated via protection port
in an APS setup
intferfaceCurrentlyNotSupported(27)
the interface type is not support currently
failure-at-call-handler(28)
interface creation failure due to call handler
unstructuredCE-payloadloop(29)
Unstructured CE should not have payload loopback as a
loop back option
channelConfigModeNotConforming(30)
There was a limitation on the channel mode of DSP_2D card:
if there is a channel is already inService, all the
channel mode of configured channels must be the same as
that of the channel inService; all the channel mode of
unconfigured channels can only be configured the same as
that of the channel inService.
usageOfReservedTimeSlot(31)
for HD_E1, do not allow any configuration to be SET on
channel number 1 or 17 (base 1) or chan 0 or 16 (base 0).
virtualIntf-and-AtmSignaling-bothCannotBeEnabled(32)
vitual interface and signalling cannot both be enabled
at the same time
virtualUni-and-AtmSignaling-bothCannotBeEnabled(33)
vitual UNI and signalling cannot both be enabled at the
same time
virtualUni-notSupported(34)
virtual UNI is not supported
atmUni-UbrLoadBalSupp-cannotBeEnabled-whenSignalingDisabled(35)
ubr load balancing cannot be enabled when signaling is
disabled
virtualInterface-notSupported(36)
virtual interface support only allowed on APS type of cards
card-doesNotSupport-UPC(37)
only some cardTypes support UPC
atmUni-SvcVpiVci-RangeCheck-Failure(38)
Do range check provided atmSignaling is enabled
vciMinSvc <= vciMaxSvc and vpiMinSvc <= vpiMaxSvc
atmUni-SigVpiVci-Within-Svc-Range(39)
atmUni{Vpi,Vci}Sig should not be within svc range
atmUni-Ilmi-Svc-Sig-VpiVci-Clash(40)
if IlmiProtocol status and atmUniSignaling are both enabled
then the Ilmi Vpi/Vci should not fall in the Svc range and
should not be equal to signaling vpi/vci
virtualUNI-VpiNotAvailable(41)
vpi is not available for the virtual UNI
virtualUNI-InvalidVUNIId(42)
vitural UNI Index is invalid
intfNotSupported-with-ds1LineType-d4(43)
if dsx1LineType is DSX1_D4 channel, interface type can't
be atmIma
intfNotSupported-with-ds1LineCoding-ami(44)
if dsx1LineCoding is DSX1_AMI channel interface type can't
be atmIma
onlyCEsupported-with-msBitStuffing-enabled(45)
if msBitStuffing is enabled only interface type circuit
emulation is supported
vISuppConnTrafficShapingMutuallyExclusive(46)
The VI support flag and Traffic Shaping flag are mutually
exclusive
tS16onPortNotCAS(47)
must have cas on port for channel to have cas trunk line
interface
channelizationDisabled(48)
should have channelization enabled to have cas trunk line
primaryDS1InterfaceNotConfigured(49)
primary DS1 interface is not configured
primaryTMCChanNotConfigured(50)
primary timeslot management channel is not configured
primaryTMCIntfAlreadyConfiguredInAnotherIg(51)
primary timeslot management channel interface is already
configured in another interface group
primaryTMCIntfCantBeChanged(52)
primary timeslot management channel interfance can't be
changed
primaryEOCChanNotConfigured(53)
primary embeded operation channel is not configured
primaryEOCIntfAlreadyConfiguredInAnotherIg(54)
primary embeded operation channel interface is already
configured in another interface group
primaryTMC-EOCIntfShouldBeSame(55)
primary timeslot management channel and embeded operation
channel interfaces should be the same
primaryEOCIntfCantBeChanged(56)
primary embeded operation channel inteface can't be changed
primaryTMC-BackupTMCIntfCantBeSame(57)
primary and backup timeslot management channel
interfaces can't be the same
backupDS1InterfaceNotConfigured(58)
backup DS1 interface is not configured
backupTMCChanNotConfigured(59)
backup timeslot management channel is not configured
backupTMCIntfAlreadyConfiguredInAnotherIg(60)
backup timeslot management channel interface is already
configured in another interface group
backupTMCIntfCantBeChanged(61)
backup timeslot management channel interfance can't be
changed
primaryEOC-BackupEOCIntfCantBeSame(62)
primary and backup embeded operation channel interfaces
can't be the same
backupEOCChanNotConfigured(63)
backup embeded operation channel is not configured
backupEOCIntfAlreadyConfiguredInAnotherIg(64)
backup embeded operation channel interface is already
configured in another interface group
backupTMC-EOCIntfShouldBeSame(65)
backup timeslot management channel and embeded operation
channel interfaces should be the same
backupEOCIntfCantBeChanged(66)
backup embeded operation channel inteface can't be changed
newBWBelowCurrentAllocated(67)
new bandwidth is below the current allocated bandwidth
newBWBelowCurrentAllocated-SvcsBeingDeleted(68)
new bandwidth is below the current allocated bandwidth
svc is being deleted
newBWBelowCurrentAllocated-DeletePvcs(69)
new bandwidth is below the current allocated bandwidth
delete pvc
newBWAboveCurrentAllocated(70)
new bandwidth is above the current allocated bandwidth
primaryInactive-or-SecondaryActive-In-IntfProtTable(71)
an interface can't be deleted if it is in interface
protection group which is primary/inactive or secondry/active
onlyCEsupported-with-msLOSDetection-enabled(72)
if msLOSDetection is enabled, only interface type circuit
emulation is supported
nonMuxNotAllowed-with-FaxRelay(73)
DSP2 cards: if channelMode is CFG_DSP2_FAX_RELAY, aalMode
can't be D_dsp2AalMode_aal2_non_multiplexed,
invalid-DSPmode-and-AALmode-combination(74)
DSP2 cards: such DSP mode and AAL mode combination is not
allowed
noBandwidth-For-SignalingConns(75)
no bandwidth for signal connectionsro Enumeration .1.3.6.1.4.1.1751.2.18.15.4 |
powerSupplyReasonCodeIdentification for change in status of a power supply.
overload(1) overload
overloadCleared(2) overload cleared
plus5vFailed(3) +5V power supply failed
plus5vCleared(4) +5V power supply cleared
plus120vFailed(5) +120V power supply failed
plus120vCleared(6) +120V power supply cleared
minus48vFailed(7) -48V power supply failed
minus48vCleared(8) -48V power supply failedro Enumeration .1.3.6.1.4.1.1751.2.18.15.5 |
portIdPort ID used for identification in traps. Number
value is interpreted as a port of the form, SSPP,
where SS is the card slot and PP is the port
number.ro Integer32 .1.3.6.1.4.1.1751.2.18.15.6 |
lineStatusBit map of the status of a line connected to a
port.ro Integer32 .1.3.6.1.4.1.1751.2.18.15.7 |
firmwareDownloadReasonCodeThe suspected reasons of why a firmware download
would fail.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.8 |
remoteRebootReasonCodeThe result of a remote reboot request.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.9 |
saveConfigurationReasonCodeThe result of a save configuration request.
equipment-OK(1) - Save of equipment configuration
completed.
equipment-Fail-VersionControlInProgress(2)
- Save of equipment configuration failed
due to ongoing version control operation.
equipment-Fail(3) - Save of equipment configuration failed.
connections-OK(4) - Save of connection configuration
completed.
connections-Fail-VersionControlInProgress(5) -
- Save of connection configuration failed
due to ongoing version control operation.
connections-Fail(6) - Save of connection configuration failed.
routing-OK(7) - Save of routing configuration completed.
routing-Fail-VersionControlInProgress(8) -
- Save of routing configuration failed
due to ongoing version control operation.
routing-Fail(9) - Save of routing configuration failed.
all-OK(10) - Saving of all configurations completed.
all-Fail-VersionControlInProgress(11) -
- Saving of all configurations failed
due to ongoing version control operation.
all-Fail(12) - Saving of all configurations failed.
fileTransferFailed(13) - Saving of configurations to secondary
CPU failed.
fileTransferCompleted(14) - Saving of configurations to
secondary CPU completed.
unSupportedOption(15) - Unsupported save option received.
fail-backupCpuInitializationInProgress(16) -
- Save operation failed due to ongoing
secondary cpu initialization.
expect2ndCPURebootAfterSave(17) -
- Notification to expect reboot of
secondary CPU after a save operation.
expect2ndCPUCardFailedOrRemoved(18)
- Notification to expect trap indicating
removal/failure of secondary CPU after a
save operation.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.10 |
versionConfigurationReasonCodeIndicated status and results of version changing.
upgrade-Start(1) upgrade starts
upgrade-Completed(2) upgrade completed
upgrade-Fail(3) upgrade failed
downgrade-Start(4) downgrade starts
downgrade-Completed(5) downgrade completed
downgrade-Fail(6) downgrade failed
upgrade-Fail-NoVersion(7)
upgrade failed, no version
upgrade-Fail-VersionControlInProgress(8)
upgrade failed, version control is in progress
downgrade-Fail-NoVersion(9)
downgrade failed, no version
downgrade-Fail-VersionControlInProgress(10)
downgrade failed, version control is in progress
upgrade-InProgress(11) upgrade is in progress
downgrade-InProgress(12)downgrade is in progress
upgrade-sanityCheck-InProgress(13)
upgrade sanity check is in progress
downgrade-sanityCheck-InProgress(14)
downgrade sanity check is in progress
upgrade-sanityCheck-Completed(15),
upgrade sanity check is completed
downgrade-sanityCheck-Completed(16),
downgrade sanity check is completed
upgrade-Fail-SanityCheckFail(17)
upgrade failed due to sanity check failure
downgrade-Fail-SanityCheckFail(18)
downgrade failed due to sanity check failure
upgrade-Fail-BkCPUFailedToRespond(19)
upgrade failed since backup CPU failed to respond
downgrade-Fail-BkCPUFailedToRespond(20)
downgrade failed since backup CPU failed to respond
upgrade-Fail-UserAbort(21)
upgrade failed since user aborted
downgrade-Fail-UserAbort(22)
downgrade failed since user aborted
synch-Start(23) synchronization starts
synch-InProgress(24) synchronization is in progress
synch-Completed(25) synchronization is completed
synch-Fail(26) synchronization failed
synch-Fail-NoBkCPU(27)
synchronization failed since no backup CPU
synch-Fail-SameVersion(28)
synchronization failed due to the same version
synch-Fail-FileCRCFailed(29)
synchronization failed due to file CRC failure
synch-Fail-VersionControlInProgress(30)
synchronization failed since version control
is in progress
synch-Fail-UserAbort(31)
synchronization failed since user aborted
synch-Fail-SanityCheckFail(32)
synchronization failed due to sanity
check failure
synch-Fail-BkCPUFailedToRespond(33)
synchronization failed since backup CPU
failed to respond
synch-sanityCheck-InProgress(34)
synchronization sanity check is in progress
synch-sanityCheck-Completed(35)
synchronization sanity check is completed
failedToAbort(36) failed to abortro Enumeration .1.3.6.1.4.1.1751.2.18.15.11 |
percentCompleteUsed for trap fileTransferStatusNotify and
value equals the percent of the upgrade,
downgrade, or ftp download completed.ro Integer32 .1.3.6.1.4.1.1751.2.18.15.12 |
ipTypeReasonCodeIndicator of which ip address had the problem.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.13 |
timingReasonCodeIndicator of type of relationship violated.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.14 |
alarmCardReasonCodeConfiguration status of the alarm inputs and
outputs. cutoff - alarm turned off. There are two ways to
turn off the audible alarm, locally via the pushbutton switch
on the alarm module, and remotely, via the remote alarm
cutoff, one of the alarm card inputs.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.15 |
removeConfigFilesUsed to indicate the status of a remove
configuration files request.
from-PrimaryCPU(1)
configuration files are removed from primary CPU
from-BackupCPU(2)
configuration files are removed from backup CPU
chassisReboot(3)
chassis reboot being done after removing
configuration files
failed-VersionControlInProgress(4)
configuration file removal failed due to ongoing
version conflictro Enumeration .1.3.6.1.4.1.1751.2.18.15.16 |
spvcConfigFailureCodeAn identified reason for failure while
configuring/modifying SPVC parameters.
noSpvcConfigured(1) : There endpoint has not been configured
as SPVC, so SPVC parameters cannot be modified.
spvcAlreadyConfigured(2) : SPVC is already configured so it cannot
be configured again as SPVC endpoint.
noInterfaceConfigured(3) : There is no interface configured on the
particular SSPPCCC.
interfaceNotConfiguredAsRequired(4) : While configuring an SPVC
endpoint, the interface is not as desired (e.g.it is not CE,
while trying to configure CES SPVC).
notActiveSpvc(6) : If the endpoint is configured with flowType
ptToMptA2B the connType has to be activeSvc.
slotA-OutofRange(7) : A-side of SPVC connection has slot number
out of range.
portA-OutofRange(8): A-side of SPVC connection has port number
out of range.
channelA-OutofRange(9): A-side of SPVC connection has channel number
out of range.
vpiVciWithInSvcRange(10) : A-side side of SPVC connection has vpi/vci
configured in the SVC range of the A-side ATM interface.
retryIntervalExceedsTheLimit(11) : retryInterval exceeds 3600s.
interfaceNotConfiguredAsCE(12) : SPVC endpoint is configured as
something other than CE.
interfaceNotConfiguredAsVbr(13) : SPVC endpoint is configured as
something other than TE.
interfaceNotConfiguredAsAtm(14) : SPVC endpoint is configured as
something other than ATM.
noAddressConfiguredOnTheInterface(15) : Local address not configured
for the particular SPVC being configured.
localAddressNotValid(16) : invalid NSAP address format
vpiVciUnavailable(17) : SPVC already setup on particular vpi/vci.
pvcAlreadySetupOnVpiVci(18) : vpi/vci being used by another pvc.
pvcAlreadySetupOnInterface(19) : redundant, same as above.
interfaceNotConfiguredAsFr(21) : SPVC endpoint is configured as
something other than Fr
dlciUnavailable(22) : dlci not available at Passive endpoint.
pvcAlreadySetupOnDlci(23) : dlci being used by another pvc.
frTrafficParamsUnsupp(24) : fr-atm traffic mapping failure.
dsp2ParamsUnsupp(25) : dsp2 params not supported for the call.
sarNotConfigReq(26) : sarType not configured as required.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.17 |
imaGrpChannelStatusThe return value for the imaGrpChannelFailNotify trap.
startupFe(1) Far-end is in the state of start-up
cfgAbort(2) this state is entered when the far-end tries to
use unacceptable configuration parameters including
invalid frame length and incompatable symmetry
cfgAbortFe(3) Far-end reported unacceptable configuration
parameters including invalid frame length and
incompatable symmetry
insuffLinks(4) Near-end reported less than the min number of
Tx links are active or less than the min number
of Rx links are active
insuffLinksFe(5) Far-end reported less than the min number of
Rx links are active or less than thenmin number
of Tx links are active
blockedNe(6) Near-end is administratively out-of-service
blockedFe(7) Far-end is administratively out-of-service
timingSynch(8) A possible configuration mismatch has
occurred (CTC and CTC modes are not the same
at both ends of the IMA virtual links.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.18 |
atmImaIntfStatusThe return value for the atmImaIntfFailNotify trap.
lif
(Loss of IMA Frame)
lods
(Link Out of Delay Synchronization)
txMisConnect
the same far-end as the other links in the
group.)
rfi
(Remote Failure Indicator)
fault
txUnusableFe
behavior
rxUnusableFe
behaviorro Enumeration .1.3.6.1.4.1.1751.2.18.15.19 |
deviceIddevice ID is used as the number of external
devices. Each device can be an external input
device or control output device.ro Integer32 .1.3.6.1.4.1.1751.2.18.15.20 |
oamTestFailureReasonCodeAn identified reason why an OAM Loopback Test
request has failed.
invalidSPCforOAM: There is no such slot/port/channel in this box.
invalidIntfForOAM: There is no such interface that
OAM enabled.
invalidLocationLength: The length of the Loopback Lo cation ID id not valid.
oamNotSupportedForThisConnection: This connection is
not OAM enabled.so OAM loopback is invalid test.
loopbackTestAlreadyRunning: OAM loopback is waiting
for response,not expect for another test.
loopbackTestNotRunning: Invalid Test Actio.
oamLocalResourcesUnavailable: Memery Alloc Fail.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.21 |
pnniCodeAn identified reason for Miscellaneous Reasons in PNNI Configuration
pnniInvEndSysPortId(1) : Invalid EndSystem PortId.
pnniNodeAdmStatNotUp(2) : Admin Status of Node is not up.
pnniProtLnkStatDown(3) : Pnni Lnk status is down.
pnniProtLnkStatUpNotAdv(4) : Pnni Lnk status up but not advertised.
pnniProtLinkStatUpAdv(5) : Pnni Lnk status up and advertised.
pnniIntfAdmStatUp(6) : Pnni Intf Admin Status up.
pnniNodeNotCfg(7) : Pnni Node not configured in the switch.
pnniRtAddrAddedByIlmi(8) : Pnni Route added succesfully from ILMI.
pnniRtAddrDelByIlmi(9) : Pnni Route deleted succesfully from ILMI.
pnniLvlMismatchInNodeId(10) : Level mismatch in Node Id.
pnniLvlMismatchInPGId(11) : Level mismatch in Peer Group Id.
pnniATMAddrInvInNodeId(12) : ATM Address entered in Node Id invalid.
pnniATMAddrInvInPGId(13) : ATM Address entered in Peer Group Id invalid.
pnniIntfAdmStatNotDel(14) : Pnni Intf Admin Status Not deleted.
pnniNodeAdmStatUp(15) : Pnni Node Admin Status up.
pnniNodeRowStatNotActive(16) : Pnni Node Row Status not active - cannot
modify
pnniNewRtAddrAdded(17) : New route added into pnni route address table.
pnniRtAddrMod(18) : Route modified in pnni Address table.
pnniAdvtNodeIdNotMine(19) : Advertised NodeId does not belong to this psax.
pnniFeatureNotSupported(20) : pnni feature unsupported.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.22 |
swtchNodeIndxSwitch Node Index for PNNI.ro Integer32 .1.3.6.1.4.1.1751.2.18.15.23 |
oc3APSPairPortIndexAPS Pair Port index - SSPP Integer32 .1.3.6.1.4.1.1751.2.18.15.24 |
oc3APSReasonCodeEnumerated values of the outcome of previous
apsPair UserCommand or alarms on the line
local - near-end
remote - far-end
working - working port
protect - protecting port
DoNotRevert - after switching from working line to
protection line, don't revert to working
line even it returns to work
ManualSw - switch over by user command
SD - signal degradation
SF - signal failure
Forced - force switch over
LockOut - don't allow switch over to a linero Enumeration .1.3.6.1.4.1.1751.2.18.15.25 |
oc3APSK1K2RxRx K1/K2 followed by hex value of K1, K2ro OCTET STRING .1.3.6.1.4.1.1751.2.18.15.26 |
oc3APSK1K2TxTx K1/K2 followed by hex value of K1, K2ro OCTET STRING .1.3.6.1.4.1.1751.2.18.15.27 |
oc3APSSelectorStateWorking port: active/standby Protection port:
standby/activero Enumeration .1.3.6.1.4.1.1751.2.18.15.28 |
oc3APSWorkingLineSignalStatusLine Status of the working port sent in a trap
enumeration explanations are the same as those of
oc3APSProtectionLineSignalStatusro Enumeration .1.3.6.1.4.1.1751.2.18.15.29 |
oc3APSProtectionLineSignalStatusLine Status of the protection port sent in a trap.
noAlarm(1) no alarm
signalDegradation(2) signal bit error rate is higher than
the specified threshold
signalFailure(4) signal bit error rate is much higher
than the specified threshold
lostCellDelineation(8) unable to identify cell boundary
switchByteFailure(16) switch bytes(k1,k2) of SONET header
have invalid code
ais-l(32) line header of SONET frame gives
alarm indication signal
ais-p(64) path header of SONET frame gives
alarm indication signal
lop(128) 1)a valid STS or VT pointer can't be
obtained by using the pointer
interpretation rules and the pointer
word doesn't contain all-ones;
2)a number of consecutive with the
NDF set to 1001 but not indicating
concatenation is received
lof(256) loss of frame
los(512) loss of signal
moduleFailure(1024) module failurero Enumeration .1.3.6.1.4.1.1751.2.18.15.30 |
arpStatusSuccess: Arp Data is Available.
Failure: Reply from RS Card timed-out.
TryAgain: The request was not honoured as it came
too soon (within a sec). Try again after 1 sec
and we will return either Success or Noroutes.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.31 |
routingStatusSuccess: Routing Data is Available.
Failure: Reply from RS Card timed-out.
TryAgain: The request was not honoured as it came
too soon (within a sec). Try again after 1 sec
and we will return either Success or Noroutes.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.32 |
vpnTrapStatusReturn codes for route server VPN level
operations.
vpnAddOk(1) VPN Creation OK
vpnInternalFailure(2) Memory Corruption Failure
vpnTooMany(3) Exceeded Max # of VPNs
vpnBadSlot(4) Impossible Slot Number
vpnBadId(5) VPN ID Must Be Between 1-6
vpnBadState(6) VPN State Machine Confused
vpnBadTimerVal(7) Bad Timer Value: State Machine
vpnAlreadyExists(8) VPN Already Exists
vpnCantLocate(9), Cannot Find Referenced VPN
vpnDelInProgress(10) Deletion In Progress -Must Wait
vpnLockedIdle(11) VPN Taken Out Of Service
vpnGeneralFailure(12) Reference Prev.Trap For Reason
vpnNotAllowed(13) Operation Not Allowed
vpnShutting(14) Shutting Down VPN -Must Wait
vpnDisabled(15) Some VPN SubSystem Not Working
vpnModifyOk(16) Modify Operation OKro Enumeration .1.3.6.1.4.1.1751.2.18.15.33 |
ipIntfStatusReturn codes for route server IP interface
operations.
intOK(1) Interface OK.
intIntFailure(2) Memory Corruption
intTooMany(3) Exceeded Max # Of Interfaces
intBadSlot(4) Impossible Slot Number
intBadId(5), Impossible Interface ID
intBadState(6) State Machine Confused
intBadTimer(7) Bad Timer Value: State Machine
intExists(8) Interface Already Exists
intCantFind(9) Unused
intDelInProgress(10) Deleting: -Must Wait
intLockedIdle(11) Interface Taken Out Of Service
intBadNetMask(12) Illegal Network Mask
intShutting(13) Shutting Down -Must Wait
intDisabled(14) Some Subsystem Not Working
intNotHostAddr(15) Host Address Is Missing
intBadIpAddr(16) Illegal IP Address
intBadRouterId(17) Illegal VPN/Router ID
intBadIntfId(18) Illegal Interface ID
intCantFindRouter(19) No Corresponding VPN
intCantFindIntf(20) Interface Does Not Exist
intCantOnSameSubnet(21) Interface Already On This Subnet
intCantModIntfAddr(22) Cannot Change Interface Addr
intCantModIntfMask(23) Cannot Change Interface Mask
intCantModIntfRipVer(24) Cannot Change Rip Ver #ro Enumeration .1.3.6.1.4.1.1751.2.18.15.34 |
subChanStatusReturn codes for route server sub channel
connections operations.
scOK(1) SubChannel OK
scIntFailure(2) Memory Corruption
scTooMany(3) Too Many SubChannels
scBadSlot(4) Impossible Slot Number
scBadId(5) Bad VPN ID
scBadState(6), State Machine Confusion
scBadTimerVal(7) Bad Timer Value: State Machine
scExists(8) SubChannel Already Exists
scCantFind(9) Unused
scDelInProgress(10) Deleting: -Must Wait
scLockedIdle(12) SubChannel Taken Out Of Serv.
scSameVc(13) Connection In Use Already
scFailedSetup(14) Referene Previous Trap
scShutting(15) Shutting Down: -Must Wait
scDisabled(16) SubSystem Disabled.
scSetupErr(17)
scRemvErr(18) Error Removing SubChannel
scBadPortNo(19) Bad Port Specified
scBadImIpAddr(20) Bad InBand IP Address
scBadRouterId(21) Bad VPN/Router ID
scBadIntfId(22) Impossible Interface ID
scBadChanId(23) Impossible Channel ID
scCantFindRouter(24) Cannot Find VPN
scCantFindIntf(25) Cannot Find Interface
scCantFindChan(26) Cannot Find SubChannelro Enumeration .1.3.6.1.4.1.1751.2.18.15.35 |
routeSrvStatusReturn codes for basic route server task
operations not related to any specific VPN
or IP/Connection operation.
rsCardOK(1) Route Server OK
rsModInitFail(2) Route Server Failed Module Init.
rsIntfInitFail(3) Route Server Failed Intf. Init.
rsPortInitFail(4) Route Server Failed Port Init
rsRipUpdateIntOK(5) Rip Update Interval was updated
ok for the route server card.
rsRipUpdateIntFail(6) Rip Update Interval was not
updated mostly because of
some VPN's still in service.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.36 |
apsFailureReasonCodeIdentification of cause for automatic
protection switching failure.
protectionCard-notPresent(1) protection card doesn't exist
protectionCardType-notAPS(2)
card type of protection card is not APS
protectionCardType-incompatible(3)
card types of protection card and
working card are incompatible
protectionCard-notInUnconfiguredState(4)
protection card is already configured
protectionCard-notUnprotected(5)
protection card is not unprotected
resource-access-failure(6) internal failure application
incorrect-APSconfiguration(7)
correct aps configuration: 1)oc3APSConfiguration
of working port is working and oc3APSConfiguration
of protection port is protection
2) oc3APSConfiguration of working and protection
ports are unprotected
protectionPort-Active(8)
protection port must be inactive when breaking
aps pair
workingPort-localLoop-notAllowed(9)
working port can't be configured as localLoop
protectionPort-localLoop-notAllowed(10)
protection port can't be configured as
localLoop eitherro Enumeration .1.3.6.1.4.1.1751.2.18.15.37 |
statRtStatusReturn codes for route server static route
condititions.
statRtOk(1) Static Rt OK
statRtIntFailure(2) Memory Corruption
statRtMany(3) Too Many Static Routes
statRtSlot(4) Impossible Slot ID
statRtBadId(5) Bad VPN ID
statRtBadState(6) State Machine Confusion
statRtBadTimer(7) Bad Timer Value: State Machine
statRtExists(8) Static Rt Already Exists
statRtCantFind(9) Unused
statRtDelInProgress(10) Deleting: -Must Wait
statRtLockedIdle(11) Static Rt Taken Out Of Service
statRtBadNetMask(12) Bad Network Mask
statRtCorrelation(13) Internal Correlation Error
statRtShutting(14) Shutting Down: -Must Wait
statRtDisabled(15) SubSystem Failure
statRtBadMetric(16) Illegal Metric Value
statRtBadIPAddr(17) Bad Static Route IP Address
intfRtExists(18) Static Route On Different Intf.
statRtBadSlot(19) Impossible Slot ID
statRtBadRouterId(20) Bad VPN/Router ID
statRtBadRouteId(21) Illegal Static Route ID
statRtBadRouteNetMask(22) Bad Stat Route Network Mask
statRtBadRouteIpAddr(23) Bad Interface IP Address
statRtBadGtwyIpAddr(24) Bad Gateway IP Address
statRtBadDestIpAddr(25) Bad Destination IP Address
statRtBadDestNetMask(26) Bad Destination IP Mask
statRtCantFindRouter(27) Cannot Find VPN
statRtCantFindRoute(28) Cannot Find Static Routero Enumeration .1.3.6.1.4.1.1751.2.18.15.38 |
portFailureReasonCodeIdentification of cause for failure in changing
the parameters of a port
insufficientModuleBandwidth(1)
insufficient module bandwidth
localLoopNotAllowedWhenInAPS(2)
local loop is not allowed when a port
is in an automatic switching pair.
msBitStuffingEnabledOnlyForCE(3)
if msBitStuffing is enabled, only interface
type circuit emulation is allowed
invalidOption(4) invalid option
hasInterfaceInService(5) interface is in-service
unsupportedBaudRate(6) the baud rate is not supported
msLOSDetectionNotEnabled(7) msLOSDetection is not enabledro Enumeration .1.3.6.1.4.1.1751.2.18.15.39 |
dlciNumberThe number of the dlci being used.ro Integer32 .1.3.6.1.4.1.1751.2.18.15.40 |
ipAddrNumberThe IP address of the host/network to be echoedro IpAddress .1.3.6.1.4.1.1751.2.18.15.41 |
pingStatusReasonCodeThe response value -
Alive destination can be reached
Not Alive destination can't be reachedro Enumeration .1.3.6.1.4.1.1751.2.18.15.42 |
primarySoftwareVersionSoftware version running on primary cpu.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.15.43 |
backupSoftwareVersionSoftware version running on backup cpu.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.15.44 |
oamActDeactResultCodeVarious result codes for the operator's
command for OAM Activation-Deactivation.
eteCCActSuccTowardsFarEnd:
eteCCActSuccTowardsNearEnd:
eteCCActSuccTowardsBothEnd:
eteCCDeactSuccTowardsFarEnd:
eteCCDeactSuccTowardsNearEnd:
eteCCDeactSuccTowardsBothEnd:
ete CC Act/Deact-request send out to far/near/both end
eteCCActDeniedTowardsFarEnd:
eteCCActDeniedTowardsNearEnd:
eteCCActDeniedTowardsBothEnd:
eteCCDeactDeniedTowardsFarEnd:
eteCCDeactDeniedTowardsNearEnd:
eteCCDeactDeniedTowardsBothEnd:
ete CC Act/Deact-request is denied.
eteCCActFailedTowardsFarEnd:
eteCCActFailedTowardsNearEnd:
eteCCActFailedTowardsBothEnd:
eteCCDeactFailedTowardsFarEnd:
eteCCDeactFailedTowardsNearEnd:
eteCCDeactFailedTowardsBothEnd:
ete CC Act/Deact-request is failed sent out
segCCActSuccTowardsFarEnd:
segCCActSuccTowardsNearEnd:
segCCActSuccTowardsBothEnd:
segCCDeactSuccTowardsFarEnd:
segCCDeactSuccTowardsNearEnd:
segCCDeactSuccTowardsBothEnd:
segment CC Act/Deact-request send out to far/near/both end.
segCCActDeniedTowardsFarEnd:
segCCActDeniedTowardsNearEnd:
segCCActDeniedTowardsBothEnd:
segment CC Act-request is denied.
segCCActFailedTowardsFarEnd:
segCCActFailedTowardsNearEnd:
segCCActFailedTowardsBothEnd:
ete CC Act-request is failed sent out.
oamReqFunctionNotImplemented: The function user issued is not impemeted.
oamActDeactPrevReqInProgress: this interface is in wait for response
state.
SendPMCell: a management cell has been sent out to IO card indicating
PM cell need to be sent.
eteReceiveBRErrMessage: a BR message has been forwarded to CPU indicating
BR error.
receiveFPMErrMessage: a FPM message has been forwarded to CPU indicating
FPM error.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.45 |
tasCmprsAnnceReasonCodeThe result of a compress announcement request.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.46 |
tasTstLineReasonCodeThe result of a test line request.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.47 |
gr303PPSReasonCodeThese reason codes are the result of GR303
Path Protection Switching (PPS) command issued by userro Enumeration .1.3.6.1.4.1.1751.2.18.15.48 |
gr303PPSSourceIndicates the initiator of the PPS switchingro Enumeration .1.3.6.1.4.1.1751.2.18.15.49 |
tasMemReasonCodeThe result of a memory init request.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.50 |
tasTrapTstIdAnnouncement ID for trap.ro INTEGER .1.3.6.1.4.1.1751.2.18.15.51 |
tasTrapAnnceIdtest id for trap.ro INTEGER .1.3.6.1.4.1.1751.2.18.15.52 |
atmVpiVpi is used in identification of Trapsro INTEGER .1.3.6.1.4.1.1751.2.18.15.53 |
atmVciVci is used in identification of Trapsro INTEGER .1.3.6.1.4.1.1751.2.18.15.54 |
iptResultCodeVarious result codes for the operator's
command forsetting/deleting interface protection group.
interfaceProtectioniptAlreadyExistInterface: Expect
another interface to be protected.
interfaceProtectioniptInvalidInterface:interface invalid
interfaceProtectioniptInvalidParams: invalid Parameters
interfaceProtectioniptTryToDeleteEmptyTable:Table is
already empty,can not be deleted .
interfaceProtectioniptInvalidConfiguation:
interfaceProtectioniptSuccessfulSwichOver: interface
is switched over to the secondry interface.
interfaceProtectioniptSuccessfulSwichBack: interface
is switched back from secondry interface.
interfaceProtectioniptFailedSwichOver: interface
is failed switched over to the secondry interface.
interfaceProtectioniptFailedSwichBack: interface
is failed switched back from secondry interface.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.55 |
pgtResultCodeVarious result codes for the operator's
command for interface protection .ro Enumeration .1.3.6.1.4.1.1751.2.18.15.56 |
tasmControlBlockAllocFailReasonCodeThe result of a tasm control block memory
allocation request.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.57 |
tasmCacheMemAllocFailReasonCodeThe result of a tasm control block memory
allocation request.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.58 |
atmTrunkingConfigFailureCodeAn identified reason for failure while
configuring/modifying
ATM Trunking parameters:
localIWFAlreadyConfigured(1) : Local IWF has
already been configured, the
parameters can not be changed or apply again.
localIWFAtmAddressError(2): the ATM Address for
Local IWF is not valid or
this address has been used by someone else.
localIWFIdOutOfRange(3): the Identification of
Local IWF is out of range.
maxNumberRmtIWFOutOfRange(4): the maximum number
of Remote IWF is out of range.
rmtIWFAlreadyConfigured(5): this remote IWF has
already been configured(
with index atmTrunkingRmtIWFIdentifier).
rmtIWFIdOutOfRange: the identifier for the remote
IWF is out of range.
rmtIWFAtmAddressError: the ATM Address for remote
IWF is not valid or
this address has been used by someone else.
vccIdError: the VCC ID for the SigVcc or BrVcc
is 0, or this VCC ID is out of range
or it has been used by someone else.
vccPvcParameterNotAcceptable: the parameters
of PVC side, including slot, port, channel,
vpi, vci, are not acceptable.
vccTrafficParameterNotValid: the VCC traffic
parameters are not acceptable,
including FwPcr01, BwPcr01, FwScr01, BwScr01,
FWMbs01, BwMbs01, BrVccServiceType, BrVccSarType.
vccViVuniNotValid: the configuration of Egress
Vi/VUNI is not acceptable.
vccTrunkParameterNotValid: the parameters for the
Trunk is not supported,
including BrVccMaxAal2ChanId,
BrVccCircuitModeDataSupp,
BrVccFrameModeSupp, BrVccFaxModeSupp,
CASPktXportSupp,
BrVccDTMFPktXportSupp, BrVccMFR1PktXportSupp,
BrVccMFR2PktXportSupp, BrVccPCMEncoding,
BrVccMaxFrameLength,
BrVccIdleChannSuprSupp, BrVccSilenceDetSupp,
BrVccCompressionSpec,AudioProfileId,
SigVccSignaling.
vccTrunkFeatureParameterNotValid: PSAX proprietary
feature parameters not supported
including SigVccInactiveTimer, SigVccRetryTimer,
SigVccRetryLimit,
BrVccInactiveTimer, BrVccRetryTimer,
BrVccRetryLimit, BrVccGr303Supp, BrVccOamStatus.
localIwfNotConfigured(14) :
Local IWF not Configured
localIwfIdNotMatch(15):
specified Local IWF not match
localIwfStatus(16): this operation is not supported
because of the status of Local IWF
rmtIwfNotConfigured(17): Remote IWF Not Configured
rmtIwfModeNotCompatible(18): the Mode of Remote IWF
is not compatiable
rmtIwfStatus(19): this operation is not support
because of the Status of Remote IWF
vccAlreadyConfigured(20):
This VCC has been configured
vccPvcCacReject(21): PVC Configuration rejected by
Cac Reservation Function
requiredFieldMissing(22): mandatory fields missing
outOfResource(23): Atm Trunking Task or System
out of resource for this configuration
rowStatusError(24):Row Status Error with the SNMP
command
generalErrorUnspecified(25): all other unspecified
failure cause.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.59 |
sapphireIntfAddressFailReasonCodeThe result of assigning the Sapphire
Interface address when PSAX is Sapphire client.
address-ok(1), Address assignment succeeded
fail-Ilegal-IP-address(2),
Illegal IP address assigned address not matching
fail-not-match-InBandManagement-Switch-CPU-IP-Address(3)
In-Band Management IP or Switch IP or CPU IP address
fail-Switch-or-CPU-IP-Address-unconfigured(4)
Switch IP or CPU IP address unconfigured
fail-InBandManagement-IP-Address-unconfigured(5)
InBandManagement IP address unconfigured.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.60 |
chassisOverTempAlarmReasonCodeIndicator of presence of chassis
over temperature alarm.ro Enumeration .1.3.6.1.4.1.1751.2.18.15.61 |
sysControl OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.16 |
saveConfigurationsave configurationrw Enumeration .1.3.6.1.4.1.1751.2.18.16.1 |
upgradeSoftwaresoftware load managementrw Enumeration .1.3.6.1.4.1.1751.2.18.16.2 |
purgePvcConnectionspurge PVC connections on indicated interfacerw IntfIndex .1.3.6.1.4.1.1751.2.18.16.3 |
purgeRoutingTablepurge indicated routing tablerw Enumeration .1.3.6.1.4.1.1751.2.18.16.4 |
resetPortStatisticsReset the statistics counters for the given
port Id (SSPP)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.5 |
resetInterfaceStatisticsReset the interface counters for the given
port Id (SSPPCCC)rw IntfIndex .1.3.6.1.4.1.1751.2.18.16.6 |
resetAllStatisticsReset all port and interface statistics
counters, accpets any integer valuerw Integer32 .1.3.6.1.4.1.1751.2.18.16.7 |
upgradeIpAddressIP Address for upgrade ftp server.rw IpAddress .1.3.6.1.4.1.1751.2.18.16.8 |
upgradeAccountNameftp account name for access to upgrade ftp server.rw DisplayString .1.3.6.1.4.1.1751.2.18.16.9 |
upgradeAccountPasswordftp account password for access to upgrade ftp
server.rw DisplayString .1.3.6.1.4.1.1751.2.18.16.10 |
upgradeCdromFilecdrom file path on upgrade ftp server to upgrade
image library.rw DisplayString .1.3.6.1.4.1.1751.2.18.16.11 |
upgradeLicenseKeysoftware license key.rw DisplayString .1.3.6.1.4.1.1751.2.18.16.12 |
upgradeSwCopyStatusCurrent status of the ftp software upgrade
download.
Status of the software upgrade. noActivity is
the initial start state from boot-up. working
is set while ftp'ing the upgrade. The final state
is one of doneSuccessfully, doneWithError, or
aborted, all self-explanatory. It will stay in
this state until re-boot or starting an upgrade.
If the state is doneWithError then
upgradeSwErrorStatus will be set to reflect the
type of error.ro Enumeration .1.3.6.1.4.1.1751.2.18.16.13 |
upgradeSwErrorStatusThe result of the finish of the ftp software
upgrade download.
Set to a value 3-22 if upgradeSwCopyStatus is
doneWithError. Set to none if upgradeSwCopyStatus
is doneSuccessfully. Set to userAbort if
upgradeSwCopyStatus is aborted.ro Enumeration .1.3.6.1.4.1.1751.2.18.16.14 |
systemSwCopystart copy system files according to the profile.
When upgradeSwCopyStatus is working, the start
request will be ignored. Abort will have effect
only when upgradeSwCopystatus is working.rw Enumeration .1.3.6.1.4.1.1751.2.18.16.15 |
fwReleaseTableTable of firmware inventory data SEQUENCE OF FwReleaseEntry .1.3.6.1.4.1.1751.2.18.16.16 |
fwReleaseEntryRow definition for firmware inventory FwReleaseEntry .1.3.6.1.4.1.1751.2.18.16.16.1 |
fwReleaseSlotPhysical slot location. Valid range is a number
between 1 and 16. INTEGER .1.3.6.1.4.1.1751.2.18.16.16.1.1 |
fwReleaseRunningthe firmware release currently running in a
physical slot (e.g., 01.03.C01).ro OCTET STRING .1.3.6.1.4.1.1751.2.18.16.16.1.2 |
fwReleaseEpromVersionthe version of the firmware located on the I/O
card (e.g., 01.03.C01).ro OCTET STRING .1.3.6.1.4.1.1751.2.18.16.16.1.3 |
fwReleaseCurrentVersionthe version of the firmware located in
/scsi/current/io on the CPU disk drive
(e.g., 01.03.C01).ro OCTET STRING .1.3.6.1.4.1.1751.2.18.16.16.1.4 |
fwReleaseNextVersionthe version of the firmware located in
/scsi/next/io on the CPU disk drive
(e.g., 01.03.C01).ro OCTET STRING .1.3.6.1.4.1.1751.2.18.16.16.1.5 |
fwReleaseUpdateUpdate the fwReleaseCurrentVersion and the
fwReleaseNextVersion variables by remapping
the firmware files from the CPU disk drive.rw Enumeration .1.3.6.1.4.1.1751.2.18.16.16.1.6 |
fwReleaseUpgradeUpdate the fwReleaseCurrentVersion and the
fwReleaseNextVersion variables by remapping
the firmware files from the CPU disk drive.rw Enumeration .1.3.6.1.4.1.1751.2.18.16.16.1.7 |
resetBridgeDomainStatisticsResets bridge domain statistics.rw Integer32 .1.3.6.1.4.1.1751.2.18.16.17 |
remoteRebootCommandtype of reboot.rw Enumeration .1.3.6.1.4.1.1751.2.18.16.18 |
resetFrLmiStatisticsReset the frame relay LMI statistics counters for
the given port Id (SSPPCCC)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.19 |
removeConfigurationFilesRemoves the user configuration/connection files
from the hard disk on the cpu.rw Enumeration .1.3.6.1.4.1.1751.2.18.16.20 |
systemFilesDirtyBitStatusBit mask for system files:
0: all are clean
1: console.def
2: ecd.def
4: ssid.def
8: cnctn.db
16: iisp.cbr
32: iisp.vbr
64: spvc.db
128: vipr.cfg
256: fwc.def
512: vi.db
1024: iproute.db
2048: atmvuni.dbro INTEGER .1.3.6.1.4.1.1751.2.18.16.21 |
resetAtmIlmiStatisticsReset the ATM ILMI statistics counters for
the given channel Id (SSPPCCC)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.22 |
resetImaGrpChannelStatisticsReset the IMA Group Statistics counters for the
given port Id (SSPPCCC)rw IntfIndex .1.3.6.1.4.1.1751.2.18.16.23 |
oc3APSResetStatsReset the oc3aps Group Statistics counters for
the given port Id (SSPP)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.24 |
resetsonetSectionStatisticsReset the sonetSectionCurrent Statistics
counters for the given port Id (SSPP)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.25 |
resetsonetLineStatisticsReset the sonetLineCurrent Statistics
counters for the given port Id (SSPP)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.26 |
resetsonetVTPathStatisticsReset the sonetVTPathCurrent Statistics
counters for the given port Id (SSPP)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.27 |
viprVpnResetReset the VPN statistics for VPN specified by (SSVV)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.28 |
svcRetBackupStatusIndicates backup status wrt SVC retentionro Enumeration .1.3.6.1.4.1.1751.2.18.16.29 |
resetsonetPathStatisticsReset the sonetPathCurrent Statistics
counters for the given port Id (SSPP)rw Integer32 .1.3.6.1.4.1.1751.2.18.16.30 |
ambientTemperatureAmbient temperature in degree Celcius where the
system is keptro Integer32 .1.3.6.1.4.1.1751.2.18.16.31 |
remoteDbServerGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.16.32 |
remoteDbServerIpAddressIP Address for remote database server.rw IpAddress .1.3.6.1.4.1.1751.2.18.16.32.1 |
remoteDbServerLoginftp account name for remote database
server.rw DisplayString .1.3.6.1.4.1.1751.2.18.16.32.2 |
remoteDbServerPasswordftp account password for remote database
server.rw DisplayString .1.3.6.1.4.1.1751.2.18.16.32.3 |
remoteDbServerDirectorydirectory on remote database server where
to save/restore database files from.rw DisplayString .1.3.6.1.4.1.1751.2.18.16.32.4 |
remoteDbCommandremote database operation.rw Enumeration .1.3.6.1.4.1.1751.2.18.16.32.5 |
remoteDbOperationStatusCurrent status of remote database command.ro Enumeration .1.3.6.1.4.1.1751.2.18.16.32.6 |
remoteDbOperationErrorStatusThe result at the finish of remote database
operation.ro Enumeration .1.3.6.1.4.1.1751.2.18.16.32.7 |
stratumConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.17 |
stratumSyncSourceClock source for the stratum card -
lineTiming: must have slot and port
specified in stratumPrimaryLineId.
compositeClock: local clock must
be available.rw Enumeration .1.3.6.1.4.1.1751.2.18.17.1 |
stratumPrimaryLineIdFormat SSPP (slot and port #'s) to be used
when lineTiming is specified in
stratumSyncSource.rw Integer32 .1.3.6.1.4.1.1751.2.18.17.2 |
stratumSecondaryLineIdFormat SSPP (slot and port #'s) to be used if
the primary line has failed. Zeros imply that
the stratum should switch to holdover mode
instead.rw Integer32 .1.3.6.1.4.1.1751.2.18.17.3 |
stratumLevelEnable or disable the switching over to stratum
4 when stratum 3 is not possible.rw Enumeration .1.3.6.1.4.1.1751.2.18.17.4 |
stratumLineCommandForces the stratum card to use one of the two
specified lines as its clock source when the
stratumSyncSource is lineTiming.rw Enumeration .1.3.6.1.4.1.1751.2.18.17.5 |
stratumLineTimingStatusRepresents the source of the current clock.ro Enumeration .1.3.6.1.4.1.1751.2.18.17.6 |
stratumModeCurrent status of the primary stratum card.
synchronized3(1) stratum is synchronized with accuracy
4.6 x 10e-6
synchronized4(2) stratum is synchronized with accuracy
3.2 x 10e-5
holdover(3) an operating condition of a clock that has
lost its controlling input and is using
stored data acquired while in normal
operation, to control its output
freerun(4) an operating condition of the clock whose
output signals are internally controlled
cardRemoved(5) stratum removedro Enumeration .1.3.6.1.4.1.1751.2.18.17.7 |
stratumBackupModeCurrent status of the backup stratum card.ro Enumeration .1.3.6.1.4.1.1751.2.18.17.8 |
stratumRefFailActionDefines whether the stratum should switch to
freerun or holdover on reference clock failure.rw Enumeration .1.3.6.1.4.1.1751.2.18.17.9 |
stratumPortStatusCurrent status of the primary stratum card.
portFOS indicates port frequency offset.ro Enumeration .1.3.6.1.4.1.1751.2.18.17.10 |
stratumBkupPortStatusCurrent status of the backup stratum card.
portFOS indicates port frequency offset.ro Enumeration .1.3.6.1.4.1.1751.2.18.17.11 |
activeStratumCurrent status of the backup stratum card.ro Enumeration .1.3.6.1.4.1.1751.2.18.17.12 |
cellTest OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.18 |
cellTestIfBInterface index used for testing cell transfer.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.18.1 |
cellTestVpiBVPI value for testing cell transfer to an I/O card.
Valid range is a number between 0 and 4095. If
the I/O card interface is not ATM, then this will
always be zero.rw INTEGER .1.3.6.1.4.1.1751.2.18.18.2 |
cellTestVcidBVirtual Check Id for testing cell transfer to an
I/O card. Valid range is a number between 0 and
65535. If the I/O card interface is frame relay,
this field acts as DLCI and the valid range is a
number between 0 and 1023. If the I/O card
interface is circuit emulation, then this will
always be 0.rw INTEGER .1.3.6.1.4.1.1751.2.18.18.3 |
cellTestServiceTypeService types for testing cell transferrw Enumeration .1.3.6.1.4.1.1751.2.18.18.4 |
cellTestConnTypeConnection types for testing cell transferrw Enumeration .1.3.6.1.4.1.1751.2.18.18.5 |
cellTestProtocolProtocol (interface type) on the I/Oro Enumeration .1.3.6.1.4.1.1751.2.18.18.6 |
cellTestPayLoadTxPayLoad to be transmitted on I/O interfacerw OCTET STRING .1.3.6.1.4.1.1751.2.18.18.7 |
cellTestPayLoadRxLast PayLoad received on I/O interfacero OCTET STRING .1.3.6.1.4.1.1751.2.18.18.8 |
cellTestActionPayLoad received on I/O interfacerw Enumeration .1.3.6.1.4.1.1751.2.18.18.9 |
cellTestRxPduCountValid cells received (Input Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.18.10 |
cellTestTxPduCountValid cells transmitted (Output Billing Count)ro Integer32 .1.3.6.1.4.1.1751.2.18.18.11 |
cellTestMismatchPduCountNumber of times Rx payload mismatched with Tx
payload.ro Integer32 .1.3.6.1.4.1.1751.2.18.18.12 |
cellTestStatusIndicates whether a cellTest test is in progress
or not.ro Enumeration .1.3.6.1.4.1.1751.2.18.18.13 |
cellTestVUNIBVUNI id for testing cell transfer to an I/O card.
This field is valid only for ATM interface.rw INTEGER .1.3.6.1.4.1.1751.2.18.18.14 |
sysInfo OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.19 |
sysInfoTxOneCellTotalTotal amount of cells within the transmit one
cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.1 |
sysInfoTxOneCellUsedAmount of cells currently being used within
the transmit one cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.2 |
sysInfoTxOneCellHighHigh-water mark of cells used within the
transmit one cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.3 |
sysInfoRxOneCellTotalTotal amount of cells within the receive one
cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.4 |
sysInfoRxOneCellUsedAmount of cells currently being used within
the receive one cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.5 |
sysInfoRxOneCellHighHigh-water mark of cells used within the
receive one cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.6 |
sysInfoRxMultiCellTotalTotal amount of multi-cells within the receive
multi-cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.7 |
sysInfoRxMultiCellUsedAmount of multi-cells currently being used
within the receive multi-cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.8 |
sysInfoRxMultiCellHighHigh-water mark of multi-cells used within the
receive multi-cell pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.9 |
sysInfoMsgPoolTotalTotal amount of messages within the message pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.10 |
sysInfoMsgPoolUsedAmount of messages currently being used within
the message pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.11 |
sysInfoMsgPoolHighHigh-water mark of messages used within the
message pool.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.12 |
sysInfoDiscFreeKBytesAmount of disc free space available in KB's.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.13 |
sysInfoCpuUtilization1xx.yy% - cpuUtilization1 is the xx part of it.ro INTEGER .1.3.6.1.4.1.1751.2.18.19.14 |
sysInfoCpuUtilization2xx.yy% - cpuUtilization2 is the yy part of it.ro INTEGER .1.3.6.1.4.1.1751.2.18.19.15 |
sysInfoSysUptimeAmount of time cpu has been up in seconds.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.16 |
sysInfoBadCellRxThe number of bad cells (BIP16) received so far.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.17 |
sysInfoMisalignedThe number of misaligned cells received so far.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.18 |
sysInfoClockAErrValue is 1, TRUE, if the clock on backplane A
is errored, otherwise, the value is 0, FALSE.ro INTEGER .1.3.6.1.4.1.1751.2.18.19.19 |
sysInfoClockBErrValue is 1, TRUE, if the clock on backplane B
is errored, otherwise, the value is 0, FALSE.ro INTEGER .1.3.6.1.4.1.1751.2.18.19.20 |
sysInfoBIPAErrValue is 1, TRUE, if the cell circuit on backplane
A is errored, otherwise, the value is 0, FALSE.ro INTEGER .1.3.6.1.4.1.1751.2.18.19.21 |
sysInfoBIPBErrValue is 1, TRUE, if the cell circuit on backplane
B is errored, otherwise, the value is 0, FALSE.ro INTEGER .1.3.6.1.4.1.1751.2.18.19.22 |
sysInfoDiscTotalKBytesAmount of disc space available in KB's.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.23 |
sysInfoRAMFreeKBytesAmount of RAM memory available for use in KB's.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.24 |
sysInfoRAMTotalKBytesAmount of RAM memory available on cpu card in
KB's.ro Integer32 .1.3.6.1.4.1.1751.2.18.19.25 |
msgPoolViewTableTable of Msg Pools In the System,
Used only for diagnostic purposes SEQUENCE OF MsgPoolViewEntry .1.3.6.1.4.1.1751.2.18.19.26 |
msgPoolViewEntryRow definition of Msg Pool Table MsgPoolViewEntry .1.3.6.1.4.1.1751.2.18.19.26.1 |
msgPoolViewIndexIt is the index of the MsgPool array for which
the information is requested. Information about
Msgs Which are not there in the free pool is
returned.A msg is said to be out of the free
pool by comparing the signature.
The limit being the max number of msgs allowed
on the system Integer32 .1.3.6.1.4.1.1751.2.18.19.26.1.1 |
msgPoolViewTskIdTask Id of the Sender of the Particular Msg,
This will give the integer value, has to be
converted to hex for comparisonro Integer32 .1.3.6.1.4.1.1751.2.18.19.26.1.2 |
msgPoolViewTskNameTask Name of the Sender of the Particular Msgro DisplayString .1.3.6.1.4.1.1751.2.18.19.26.1.3 |
msgPoolViewMsgCmdmsgCmd being sent by the sending Taskro Integer32 .1.3.6.1.4.1.1751.2.18.19.26.1.4 |
primaryCpuHwTypeIndicates the hardware version type of the
primary CPU.
version1: 150MHz Saturn13 board supporting
8MB-64MB Memory.
version2: 200MHz Saturn15 board supporting
64MB-256MB Memory.ro Enumeration .1.3.6.1.4.1.1751.2.18.19.27 |
secondaryCpuHwTypeIndicates the hardware version type of the
secondary CPU.
version1: 150MHz Saturn13 board supporting
8MB-64MB Memory.
version2: 200MHz Saturn15 board supporting
64MB-256MB Memory.ro Enumeration .1.3.6.1.4.1.1751.2.18.19.28 |
sysInfoDiskCheckIndicates the checking status of
the disk in CPU card.ro Enumeration .1.3.6.1.4.1.1751.2.18.19.29 |
switchAlarmStatusCurrent status of the alarm on the switch.
notAvailable - The alarm status could not be retreived.
none - No alarm is present.
minor, major, critical - An alarm of the enumerated type
is presentro Enumeration .1.3.6.1.4.1.1751.2.18.19.30 |
ethernetConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.20 |
arp1TableTable of ARP cache data. SEQUENCE OF Arp1Entry .1.3.6.1.4.1.1751.2.18.20.1 |
arp1EntryRow definition for ARP cache. Arp1Entry .1.3.6.1.4.1.1751.2.18.20.1.1 |
arp1CardSlotSlot ethernet card is in. INTEGER .1.3.6.1.4.1.1751.2.18.20.1.1.1 |
arp1BridgeGroupNumBridge Group the entry belongs to. INTEGER .1.3.6.1.4.1.1751.2.18.20.1.1.2 |
arp1IpAddressEntry IP address. IpAddress .1.3.6.1.4.1.1751.2.18.20.1.1.3 |
arp1PhysicalAddrEntry physical address.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.20.1.1.4 |
arp1EntryAgeAge of cache entry.ro Integer32 .1.3.6.1.4.1.1751.2.18.20.1.1.5 |
arp2TableTable of ARP cache data. SEQUENCE OF Arp2Entry .1.3.6.1.4.1.1751.2.18.20.2 |
arp2EntryRow definition for ARP cache. Arp2Entry .1.3.6.1.4.1.1751.2.18.20.2.1 |
arp2CardSlotSlot ethernet card is in. INTEGER .1.3.6.1.4.1.1751.2.18.20.2.1.1 |
arp2BridgeGroupNumBridge Group the entry belongs to. INTEGER .1.3.6.1.4.1.1751.2.18.20.2.1.2 |
arp2PhysicalAddrEntry physical address. OCTET STRING .1.3.6.1.4.1.1751.2.18.20.2.1.3 |
arp2IpAddressEntry IP address.ro IpAddress .1.3.6.1.4.1.1751.2.18.20.2.1.4 |
arp2EntryAgeAge of cache entry.ro Integer32 .1.3.6.1.4.1.1751.2.18.20.2.1.5 |
bridgeCacheTableTable of bridge cache data. SEQUENCE OF BridgeCacheEntry .1.3.6.1.4.1.1751.2.18.20.3 |
bridgeCacheEntryRow definition for bridge cache. BridgeCacheEntry .1.3.6.1.4.1.1751.2.18.20.3.1 |
bridgeCacheCardSlotSlot ethernet card is in. INTEGER .1.3.6.1.4.1.1751.2.18.20.3.1.1 |
bridgeCacheBridgeGroupNumBridge Group the entry belongs to. INTEGER .1.3.6.1.4.1.1751.2.18.20.3.1.2 |
bridgeCachePhysicalAddrEntry physical address. OCTET STRING .1.3.6.1.4.1.1751.2.18.20.3.1.3 |
bridgeCacheTypeType of Entry.ro Enumeration .1.3.6.1.4.1.1751.2.18.20.3.1.4 |
bridgeCacheSourcePortPort entry was obtained from.ro INTEGER .1.3.6.1.4.1.1751.2.18.20.3.1.5 |
bridgeCacheEntryAgeAge of cache entry.ro Integer32 .1.3.6.1.4.1.1751.2.18.20.3.1.6 |
alarmConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.21 |
alarmStatusInputBitmapRemote status from external device.
bit = 0 closed,
bit = 1 open,
LSB 15 bits represent 15 external inputs.
MSB bit 15 is always 0.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.21.1 |
alarmStatusOutputBitmapControl output for alarm card.
bit = 0 deactivated,
bit = 1 activated,
LSB 4 bits represent 4 external outputs.
Bit 0 through bit 3 is output 1 through 4
Control output 4 will be activated upon
power failure.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.21.2 |
alarmSeverityLevelBitmapAlarm severity level.
bit = 0 noAlarm,
bit = 1 Alarm present,
LSB 3 bits represent severity levels.
bit 0 = Minor Alarm,
bit 1 = Major Alarm,
bit 2 = Critical Alarm.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.21.3 |
alarmAcoStatusBitmapAudio alarm status.
bit = 0 No alarm cutoff,
bit = 1 Alarm cutoff,
LSB 3 bits represent audio alarms.
bit 0 = Local alarm cutoff,
bit 1 = remote alarm cutoff,
bit 2 = composite alarm cutoff status.ro OCTET STRING .1.3.6.1.4.1.1751.2.18.21.4 |
sysTest OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.22 |
oamTest OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.22.1 |
oamTestIfBInterface index used for starting loopback test.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP is
the port number, and CCC is the channel number.rw IntfIndex .1.3.6.1.4.1.1751.2.18.22.1.1 |
oamTestVpiBVPI value under testing for oam loopback test.
Valid range is a number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.22.1.2 |
oamTestVciBVCI value under testing for oam loopback test.
Valid range is a number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.22.1.3 |
oamTestStatusInidcates the current status of oam test.ro Enumeration .1.3.6.1.4.1.1751.2.18.22.1.4 |
oamTestActionTest action to be performed.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.1.5 |
oamTestTxCountValid cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.22.1.6 |
oamTestRxCountValid cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.22.1.7 |
oamTestMismatchCountNumber of times Rx correlation tag is mismatched
with the Tx correlation tag.ro Integer32 .1.3.6.1.4.1.1751.2.18.22.1.8 |
oamTestLocationIDLocation ID of the ATM Node where the loopback is
to occur.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.22.1.9 |
oamTestLoopbackTypeOAM Loopback type. Determines whether to
send ete or segment loopback cell, and the value
of location Id field in the cell. Only for
specific-location value, user specified locationId
field value taken into account.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.1.10 |
oamActDeactTableTable of oam activate and deactivate functions SEQUENCE OF OamActDeactEntry .1.3.6.1.4.1.1751.2.18.22.2 |
oamActDeactEntryRow definition of oam activate and deactivate OamActDeactEntry .1.3.6.1.4.1.1751.2.18.22.2.1 |
oamActDeactIfBInterface index for an OAM CC connection.
Number value is interpreted as an interface of the
form, SSPPCCC, where SS is the card slot, PP
is the port number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.22.2.1.1 |
oamActDeactVpiBVPI value for an oam CC connection.
Valid range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.22.2.1.2 |
oamActDeactVciBVCI value for oam CC connection.
Valid range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.22.2.1.3 |
oamActDeactFuncTypeOAM Function type represents the OAM flow for
activation or deactivattion for this connection.
the possible function types activated in one connection
are :
fpm-and-br : forward performance monitoring/backward
reporting
fpm-only : forward performance monitoring
continuity-check : continuity check
pmbr-and-cc : forward performance monitoring/backward
reporting and continuity check
pm-and-cc : forward performance monitoring and
continuity checkrw Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.4 |
oamActDeactDirFlowThe direction in which cells will be
transmitted.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.5 |
oamActDeactFlowTypeFlow Type.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.6 |
oamActDeactBlkSizeABBlock Size A-B represents the size of
the block of user cells taken into consideration
for performance monitoring in A-B direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.7 |
oamActDeactBlkSizeBABlock Size A-B is the size of the block of
user cells taken into consideration for
performance monitoring in B-A direction.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.8 |
oamActDeactStsSrcPointEteCCSource point showed in the status portion
displays the current status of Activation or
Deactivation request for the source pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.9 |
oamActDeactStsSnkPointEteCCSink point showed in the status portion
displays the current status of Activation
or Deactivation request for the sink pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.10 |
oamActDeactRsltPrevReqCause of Failure shows the reasons of failure
of the last activation request on this connection
form the local user.ro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.11 |
oamActDeactRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.22.2.1.12 |
oamActDeactStsSrcPointEtePMSource point showed in the status portion
displays the current status of Activation or
Deactivation request for the source pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.13 |
oamActDeactStsSnkPointEtePMSink point showed in the status portion
displays the current status of Activation
or Deactivation request for the sink pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.14 |
oamActDeactStsSrcPointEtePMBRSource point showed in the status portion
displays the current status of Activation or
Deactivation request for the source pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.15 |
oamActDeactStsSnkPointEtePMBRSink point showed in the status portion
displays the current status of Activation
or Deactivation request for the sink pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.16 |
oamActDeactBRBlockErrorBackware reporting Block error for PM connection.
Valid range is a number between 0 and 32768.ro INTEGER .1.3.6.1.4.1.1751.2.18.22.2.1.17 |
oamActDeactBRLostInsertedCellBackware reporting lost inserted cell for
PM connection. Valid range is a number between
0 and 32768.ro INTEGER .1.3.6.1.4.1.1751.2.18.22.2.1.18 |
oamActDeactBRMisInsertedCellBackware reporting misinserted cell for
PM connection. Valid range is a number between 0
and 32768.ro INTEGER .1.3.6.1.4.1.1751.2.18.22.2.1.19 |
oamActDeactStsSrcPointSegPMSource point showed in the status portion
displays the current status of Activation or
Deactivation request for the source pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.20 |
oamActDeactStsSnkPointSegPMSink point showed in the status portion
displays the current status of Activation
or Deactivation request for the sink pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.21 |
oamActDeactStsSrcPointSegPMBRSource point showed in the status portion
displays the current status of Activation or
Deactivation request for the source pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.22 |
oamActDeactStsSnkPointSegPMBRSink point showed in the status portion
displays the current status of Activation
or Deactivation request for the sink pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.23 |
oamActDeactStsSrcPointSegCCSource point showed in the status portion
displays the current status of Activation or
Deactivation request for the source pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.24 |
oamActDeactStsSnkPointSegCCSink point showed in the status portion
displays the current status of Activation
or Deactivation request for the sink pointro Enumeration .1.3.6.1.4.1.1751.2.18.22.2.1.25 |
oamLoopbackTableTable of oam loopback functions SEQUENCE OF OamLoopbackEntry .1.3.6.1.4.1.1751.2.18.22.3 |
oamLoopbackEntryRow definition of oam loop back OamLoopbackEntry .1.3.6.1.4.1.1751.2.18.22.3.1 |
oamLpbkIfBInterface index used for starting loopback
test. Number value is interpreted as an interface
of the form, SSPPCCC, where SS is the card slot, PP
is the port number, and CCC is the channel number. IntfIndex .1.3.6.1.4.1.1751.2.18.22.3.1.1 |
oamLpbkVpiBVPI value under testing for oam loopback test.
Valid range is a number between 0 and 4095. INTEGER .1.3.6.1.4.1.1751.2.18.22.3.1.2 |
oamLpbkVciBVCI value under testing for oam loopback test.
Valid range is a number between 0 and 65535. INTEGER .1.3.6.1.4.1.1751.2.18.22.3.1.3 |
oamLoopbackTypeOAM Loopback type. Determines whether to
send ete or segment loopback cell, and the value
of location Id field in the cell. Only for
specific-location value, user specified locationId
field value taken into account.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.3.1.4 |
oamLpbkLocationIDLocation ID of the ATM Node where the
loopback is
to occur.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.22.3.1.5 |
oamLpbkActionTest action to be performed.
endLoopbackContinuously is not used.rw Enumeration .1.3.6.1.4.1.1751.2.18.22.3.1.6 |
oamLpbkStatusInidcates the current status of oam test.ro Enumeration .1.3.6.1.4.1.1751.2.18.22.3.1.7 |
oamLpbkTxCountValid cells transmitted.ro Integer32 .1.3.6.1.4.1.1751.2.18.22.3.1.8 |
oamLpbkRxCountValid cells received.ro Integer32 .1.3.6.1.4.1.1751.2.18.22.3.1.9 |
oamLpbkMismatchCountNumber of times Rx correlation tag is
mismatched with the Tx correlation tag.ro Integer32 .1.3.6.1.4.1.1751.2.18.22.3.1.10 |
oamLpbkTimeoutnumber of time outro Integer32 .1.3.6.1.4.1.1751.2.18.22.3.1.11 |
fwDriverSup OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.23 |
cardFwVerTableTable of card firware version status SEQUENCE OF CardFwVerEntry .1.3.6.1.4.1.1751.2.18.23.1 |
cardFwVerEntryRow definition for card firmware version status CardFwVerEntry .1.3.6.1.4.1.1751.2.18.23.1.1 |
cardFwVerSlotcard slot number INTEGER .1.3.6.1.4.1.1751.2.18.23.1.1.1 |
cardFwVerTypeCard typerw Integer32 .1.3.6.1.4.1.1751.2.18.23.1.1.2 |
cardFwVerCurrentCard firmware version currently loaded on
firmwarero OCTET STRING .1.3.6.1.4.1.1751.2.18.23.1.1.3 |
cardFwVerCurrentIsDefaultcurent driver is defaultro Integer32 .1.3.6.1.4.1.1751.2.18.23.1.1.4 |
cardFwVerNextCard firmware version that user wants to
upgrade to. The values are limited those
supported by the release.rw OCTET STRING .1.3.6.1.4.1.1751.2.18.23.1.1.5 |
cardFwVerNextIsDefaultnext driver is defaultrw INTEGER .1.3.6.1.4.1.1751.2.18.23.1.1.6 |
cardFwDnldStatusfirmware download procedure statusro Enumeration .1.3.6.1.4.1.1751.2.18.23.1.1.7 |
cardFwRetriesNumber of times firmware download
procedure failed consequently.ro Integer32 .1.3.6.1.4.1.1751.2.18.23.1.1.8 |
fwDriverTableTable of available firmware drivers SEQUENCE OF FwDriverEntry .1.3.6.1.4.1.1751.2.18.23.2 |
fwDriverEntryRow definition for available firmware drivers FwDriverEntry .1.3.6.1.4.1.1751.2.18.23.2.1 |
fwSlotIddriver slot id Integer32 .1.3.6.1.4.1.1751.2.18.23.2.1.1 |
fwDriverTypefirmware driver type - definition
consistent with cardType. Integer32 .1.3.6.1.4.1.1751.2.18.23.2.1.2 |
fwIsDefaultfirmware driver wether default or not Integer32 .1.3.6.1.4.1.1751.2.18.23.2.1.3 |
fwDriverNamefirmware driver file name OCTET STRING .1.3.6.1.4.1.1751.2.18.23.2.1.4 |
fwDriverFrnFirmware Release Number of firmware driverro Integer32 .1.3.6.1.4.1.1751.2.18.23.2.1.5 |
fwDriverSizefile size of firmware driverro Integer32 .1.3.6.1.4.1.1751.2.18.23.2.1.6 |
fwDriverChecksumchecksum of firmware driver filero Integer32 .1.3.6.1.4.1.1751.2.18.23.2.1.7 |
viprConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.24 |
viprRouterConfigTableTable of Vipr Router Instance Information SEQUENCE OF ViprRouterConfigEntry .1.3.6.1.4.1.1751.2.18.24.1 |
viprRouterConfigEntrydefinition for VIPR Route instance attributes ViprRouterConfigEntry .1.3.6.1.4.1.1751.2.18.24.1.1 |
viprSlotThe slot number of the Virtual Router card (SS) Integer32 .1.3.6.1.4.1.1751.2.18.24.1.1.1 |
viprRouterIdA unique Id for the Router Instance in a router card INTEGER .1.3.6.1.4.1.1751.2.18.24.1.1.2 |
viprRouterNameThe ASCII name of the Router Instancerw DisplayString .1.3.6.1.4.1.1751.2.18.24.1.1.3 |
viprRouterNoOfInterfacesThis variable describes the no of interfaces
defined in the Router Instancero INTEGER .1.3.6.1.4.1.1751.2.18.24.1.1.4 |
viprRouterNoOfRoutesThis variable describes the no of static routes
defined in the Router Instancero INTEGER .1.3.6.1.4.1.1751.2.18.24.1.1.5 |
viprRouterAdminStatusThis variable represents the various X.731 states
the Router state machine can take Administartivelyrw Enumeration .1.3.6.1.4.1.1751.2.18.24.1.1.6 |
viprRouterOperStatusThis variable represents the various X.731 states
the Router state machine can take operationallyro Enumeration .1.3.6.1.4.1.1751.2.18.24.1.1.7 |
viprRouterInitTmrThis variable describes the waiting period in
the locked-Init state before moving onto
locked-Diable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.1.1.8 |
viprRouterDisabWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in unlocked-Disable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.1.1.9 |
viprRouterShutDwnWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in locked-Shutting state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.1.1.10 |
viprRouterDisableWarningThis variable when disabled will mask all the
warning messages.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.1.1.11 |
viprRouterDisableReasonThis variable describes the reason why the Router
in the unlocked-Disabled state.ro Enumeration .1.3.6.1.4.1.1751.2.18.24.1.1.12 |
viprRouterRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.24.1.1.13 |
viprIntfConfigTableTable of Vipr Interface Config Information SEQUENCE OF ViprIntfConfigEntry .1.3.6.1.4.1.1751.2.18.24.2 |
viprIntfConfigEntrydefinition for VIPR interface attributes ViprIntfConfigEntry .1.3.6.1.4.1.1751.2.18.24.2.1 |
viprIntfIdA unique Id for the Interface in a router instance Integer32 .1.3.6.1.4.1.1751.2.18.24.2.1.1 |
viprIntfIPAddressThe IP address of the entrprise network to which the
interface is attached torw IpAddress .1.3.6.1.4.1.1751.2.18.24.2.1.2 |
viprIntfIPNetMaskThe IP Subnet Mask of the entrprise network to which
the interface is attached torw IpAddress .1.3.6.1.4.1.1751.2.18.24.2.1.3 |
viprIntfAdminStatusThis variable represents the various X.731 states
the Interfce statemachine can take Administrativelyrw Enumeration .1.3.6.1.4.1.1751.2.18.24.2.1.4 |
viprIntfOperStatusThis variable represents the various X.731 states
the Interfce statemachine can take operationallyro Enumeration .1.3.6.1.4.1.1751.2.18.24.2.1.5 |
viprIntfInitTmrThis variable describes the waiting period in
the locked-Init state before moving onto
locked-Diable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.2.1.6 |
viprIntfDisabWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in unlocked-Disable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.2.1.7 |
viprIntfShutDwnWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in locked-Shutting state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.2.1.8 |
viprIntfDisableWarningThis variable when disabled will mask all the
Disable warning messages.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.2.1.9 |
viprIntfDisableReasonThis variable describes the reason why the Interface
in the unlocked-Disabled state.ro Enumeration .1.3.6.1.4.1.1751.2.18.24.2.1.10 |
viprIntfRipVersionThis specifies the version of RIP that interface supports.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.2.1.11 |
viprIntfRipModeThis specifies the mode in which RIP protocol runs.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.2.1.12 |
viprIntfRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.24.2.1.13 |
viprIntfRipLineTypeThis specifies the line type when the RIP version is 2.
When the RIP version is 1, the RIP line type will be
set to broadcast(1).rw Enumeration .1.3.6.1.4.1.1751.2.18.24.2.1.14 |
viprIntfAuthPasswdThe authentication password for RIP version 2rw DisplayString .1.3.6.1.4.1.1751.2.18.24.2.1.15 |
viprSubChnlConfigTableTable of Vipr Sub Channel Config Information SEQUENCE OF ViprSubChnlConfigEntry .1.3.6.1.4.1.1751.2.18.24.3 |
viprSubChnlConfigEntrydefinition for VIPR sub channel attributes ViprSubChnlConfigEntry .1.3.6.1.4.1.1751.2.18.24.3.1 |
viprSubChnlIdA unique Id for the sub channel in the interface Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.1 |
viprSubChnlIntfIndexThe Slot Port Channel to which the IP Packet to be
forwarded when the TOS specified in the incoming
IP packet is matched to the TosValue, TosMask pairrw IntfIndex .1.3.6.1.4.1.1751.2.18.24.3.1.2 |
viprSubChnlTrafficTypeThe type of interface configured on the SSPPCCC,
viprSubChnlIntfIndexrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.3 |
viprSubChnlLlcEncapTypeThe encapsulation technique used in making IP packet
to ATM cellrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.4 |
viprSubChnlMacEncapTypeThe encapsulation technique used in making IP packet
to ATM cellrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.5 |
viprSubChnlTosFeatureAllow the user to set the TOS values or notro Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.6 |
viprSubChnlTosValueThe type of service specified in IP packet masked
with viprSubChnlTosMask has to be equal to this
value in order to have the IP packets getting
forwarded in this sub channelro INTEGER .1.3.6.1.4.1.1751.2.18.24.3.1.7 |
viprSubChnlTosMaskThe Type of Service maskro INTEGER .1.3.6.1.4.1.1751.2.18.24.3.1.8 |
viprSubChnlVpiDlciThe VPI/DLCI value of the connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.24.3.1.9 |
viprSubChnlVciThe VCI value of the connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.24.3.1.10 |
viprSubChnlSarTypeThe SAR Type supported for the connectionro Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.11 |
viprSubChnlServiceTypeThe Service types that are supportedrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.12 |
viprSubChnlFwdErrCorrectionThe Forward error correction to be usedrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.13 |
viprSubChnlInterworkingTypeThe Encapsulation type used for Frame relay subchannelsrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.14 |
viprSubChnlFrameSizeThe value of this object is the size in octets of
the largest frame relay information field for this
PVC in the ingress direction (out of the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.15 |
viprSubChnlComBurstSizeThe value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this PVC in the ingress
direction (into the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.16 |
viprSubChnlExcessBurstSizeThe value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this PVC in the ingress direction (into
the frame relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.17 |
viprSubChnlCommitedInfoRateThe value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this PVC
in the ingress direction (into the frame
relay UNI).rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.18 |
viprSubChnlTimeIntervalThe time interval over which CIR and the burst
sizes (Bc and Be) are measured in the A2B
direction. The unit is milliseconds.ro INTEGER .1.3.6.1.4.1.1751.2.18.24.3.1.19 |
viprSubChnlAtmPeakCellRatePeak cell rate, in cells per second,
this will reflect the frame relay parameters in
atm terms.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.20 |
viprSubChnlAtmSustainedCellRateSustained cell rate, in cells per second,
this will reflect the frame relay parameters in
atm terms.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.21 |
viprSubChnlAtmMaxBurstSizeMaximum burst size, in cells,
this will reflect the frame relay parameters in
atm terms.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.22 |
viprSubChnlFrPeakCellRatePeak cell rate, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.23 |
viprSubChnlFrSustainedCellRateSustained cell rate, in cells per second,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.24 |
viprSubChnlFrMaxBurstSizeMaximum burst size, in cells,
this will reflect the frame relay parameters in
atm terms.ro Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.25 |
viprSubChnlFlowTypeThe type of flowrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.26 |
viprSubChnlAdminStatusThis variable represents the various X.731 states
the Sub Channel state machine can take Administartivelyrw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.27 |
viprSubChnlOperStatusThis variable represents the various X.731 states
the Sub Channel state machine can take Operationallyro Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.28 |
viprSubChnlInitTmrThis variable describes the waiting period in
the locked-Init state before moving onto
locked-Diable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.29 |
viprSubChnlDisabWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in unlocked-Disable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.30 |
viprSubChnlShutDwnWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in locked-Shutting state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.3.1.31 |
viprSubChnlDisableWarningThis variable when disabled will mask all the
Disable warning messages.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.32 |
viprSubChnlDisableReasonThis variable describes the reason why the SubChnl
in the unlocked-Disabled state.ro Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.33 |
viprSubChnlRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.24.3.1.34 |
viprSubChnlImIpAddrinband management IpAddrrw IpAddress .1.3.6.1.4.1.1751.2.18.24.3.1.35 |
viprSubChnlImMaskinband management Maskrw IpAddress .1.3.6.1.4.1.1751.2.18.24.3.1.36 |
viprSubChnlViBThe viB value of the connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.24.3.1.37 |
viprSubChnlVUNIBThe VUNIB value of the connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.24.3.1.38 |
viprSubChnlTrafficShapingTraffic Shaping Support in the A2B direction
for outgoing ATM connections.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.39 |
viprSubChnlAtmOamStatusIndicates the OAM monitoring status.
The 3 possible states are:
Unsupp: No monitoring enabled.
End-Pt: A side is only an end point, therefore
it will respond to AIS/RDI.
End-Seg-Pt: Connection endPoint that is also
a segment endPoint.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.3.1.40 |
viprRouteConfigTableTable of Vipr static route Config Information SEQUENCE OF ViprRouteConfigEntry .1.3.6.1.4.1.1751.2.18.24.4 |
viprRouteConfigEntryDefinition for Vipr static route attributes ViprRouteConfigEntry .1.3.6.1.4.1.1751.2.18.24.4.1 |
viprRouteIdThe unique Id to the routing table entry Integer32 .1.3.6.1.4.1.1751.2.18.24.4.1.1 |
viprRouteIPAddressThe IP address of the host/network in the route
entryrw IpAddress .1.3.6.1.4.1.1751.2.18.24.4.1.2 |
viprRouteIPNetMaskThe IP Subnet Mask for the route entry to identify
whether the route entry is a host or networkrw IpAddress .1.3.6.1.4.1.1751.2.18.24.4.1.3 |
viprRouteDestAddressThe IP address of the host/network in the route
entryrw IpAddress .1.3.6.1.4.1.1751.2.18.24.4.1.4 |
viprRouteGatewayAddressThe IP address of the Gatewayrw IpAddress .1.3.6.1.4.1.1751.2.18.24.4.1.5 |
viprRouteServiceTypeThe Service types that are supportedrw Enumeration .1.3.6.1.4.1.1751.2.18.24.4.1.6 |
viprRouteMetricA scalar value for user-supplied static
route metric values.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.4.1.7 |
viprRouteAdminStatusThis variable represents the various X.731 states
the Route state machine can take Administrativelyrw Enumeration .1.3.6.1.4.1.1751.2.18.24.4.1.8 |
viprRouteOperStatusThis variable represents the various X.731 states
the Route state machine can take Operationallyro Enumeration .1.3.6.1.4.1.1751.2.18.24.4.1.9 |
viprRouteInitTmrThis variable describes the waiting period in
the locked-Init state before moving onto
locked-Diable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.4.1.10 |
viprRouteDisabWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in unlocked-Disable state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.4.1.11 |
viprRouteShutDwnWarnTmrThis variable describes the periodicity in which
the error messages are to be flashed when the
system is in locked-Shutting state.rw Integer32 .1.3.6.1.4.1.1751.2.18.24.4.1.12 |
viprRouteDisableWarningThis variable when disabled will mask all the
Disable warning messages.rw Enumeration .1.3.6.1.4.1.1751.2.18.24.4.1.13 |
viprRouteDisableReasonThis variable describes the reason why the
Route in the unlocked-Disabled state.ro Enumeration .1.3.6.1.4.1.1751.2.18.24.4.1.14 |
viprRouteRowStatusrow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.24.4.1.15 |
viprRouteDestMaskThe IP Mask of the host/network in the route
entryrw IpAddress .1.3.6.1.4.1.1751.2.18.24.4.1.16 |
viprRoutingConfigTableTable of Vipr routes Config Information SEQUENCE OF ViprRoutingConfigEntry .1.3.6.1.4.1.1751.2.18.24.5 |
viprRoutingConfigEntryDefinition for Vipr route attributes ViprRoutingConfigEntry .1.3.6.1.4.1.1751.2.18.24.5.1 |
viprRoutingCommandThe Routing table request command
Set to start to initiate the caching of first 15 entries
Set to more to initiate the caching of next 15 entries
Set to abort to reset the counter in I/O card
Set to retrieve in order to get the entries Enumeration .1.3.6.1.4.1.1751.2.18.24.5.1.1 |
viprRoutingIPAddressThe IP address of the host/network in the route
entryro IpAddress .1.3.6.1.4.1.1751.2.18.24.5.1.2 |
viprRoutingIPNetMaskThe IP Subnet Mask for the route entry to identify
whether the route entry is a host or networkro IpAddress .1.3.6.1.4.1.1751.2.18.24.5.1.3 |
viprRoutingDestAddressThe IP address of the host/network in the route
entryro IpAddress .1.3.6.1.4.1.1751.2.18.24.5.1.4 |
viprRoutingGatewayAddressThe IP address of the Gatewayro IpAddress .1.3.6.1.4.1.1751.2.18.24.5.1.5 |
viprRoutingServiceTypeThe Service types that are supportedro Enumeration .1.3.6.1.4.1.1751.2.18.24.5.1.6 |
viprRoutingTypeRoute types supported by the RS Card.ro Enumeration .1.3.6.1.4.1.1751.2.18.24.5.1.7 |
viprRoutingMetricThe Path costro Integer32 .1.3.6.1.4.1.1751.2.18.24.5.1.8 |
viprRoutingDestMaskThe IP address Mask of the host/network in the route
entryro IpAddress .1.3.6.1.4.1.1751.2.18.24.5.1.9 |
viprRoutingAgeAge of the routing entryro Integer32 .1.3.6.1.4.1.1751.2.18.24.5.1.10 |
viprRoutingIndexIndex to the routing entry Integer32 .1.3.6.1.4.1.1751.2.18.24.5.1.11 |
viprArpConfigTableTable of Vipr Arp Table Information SEQUENCE OF ViprArpConfigEntry .1.3.6.1.4.1.1751.2.18.24.6 |
viprArpConfigEntryDefinition for Vipr Arp Table attributes ViprArpConfigEntry .1.3.6.1.4.1.1751.2.18.24.6.1 |
viprArpCommandThe ARP table request command
Set to start to initiate the caching of first 15 entries
Set to more to initiate the caching of next 15 entries
Set to abort to reset the counter in I/O card
Set to retrieve in order to get the entries Enumeration .1.3.6.1.4.1.1751.2.18.24.6.1.1 |
viprArpIPAddressThe IP address of the host/networkro IpAddress .1.3.6.1.4.1.1751.2.18.24.6.1.2 |
viprArpHwAddressThe hardware address of the host/networkro OCTET STRING .1.3.6.1.4.1.1751.2.18.24.6.1.3 |
viprArpEntryAgeAge of cache entry.ro Integer32 .1.3.6.1.4.1.1751.2.18.24.6.1.4 |
viprArpInterfaceIPAddressThe Interface IP address through which it is learnedro IpAddress .1.3.6.1.4.1.1751.2.18.24.6.1.5 |
viprArpInterfaceIPMaskThe Interface IP address Maskro IpAddress .1.3.6.1.4.1.1751.2.18.24.6.1.6 |
viprArpInterfaceServiceTypeThe Service type of the interface through which the
ARP table is learnedro Enumeration .1.3.6.1.4.1.1751.2.18.24.6.1.7 |
viprArpIndexThe Index to the Arp table Integer32 .1.3.6.1.4.1.1751.2.18.24.6.1.8 |
viprPingConfigTableTable of Vipr Ping Table Information SEQUENCE OF ViprPingConfigEntry .1.3.6.1.4.1.1751.2.18.24.7 |
viprPingConfigEntryDefinition for Vipr Ping Table attributes ViprPingConfigEntry .1.3.6.1.4.1.1751.2.18.24.7.1 |
ipAddrThe IP address of the host/network to be echoed IpAddress .1.3.6.1.4.1.1751.2.18.24.7.1.1 |
pingStatusThe response value - Alive/Not Alivero Enumeration .1.3.6.1.4.1.1751.2.18.24.7.1.2 |
viprRipConfigTableTable of Vipr Rip Update Interval for each card SEQUENCE OF ViprRipConfigEntry .1.3.6.1.4.1.1751.2.18.24.8 |
viprRipConfigEntryDefinition of Rip Update attributes ViprRipConfigEntry .1.3.6.1.4.1.1751.2.18.24.8.1 |
viprRipUpdateIntThis variable represents the Rip Update Interval
used by the RIP protocol to transmit packets.
The unit is in seconds. The default is 30 seconds
and user can change it to 8 or 16 seconds for a
route server card. The value will apply to all
VPN's in a route server card. But different
route server cards in different slots can have
separate values for Rip Update Intervalrw Enumeration .1.3.6.1.4.1.1751.2.18.24.8.1.1 |
toneAnnceControl OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.25 |
tasCmprsAnnceIdAnnouncement ID for this announcement file
to be compressed.rw INTEGER .1.3.6.1.4.1.1751.2.18.25.31 |
tasCmprsAnnceReplaceIdAnnouncement ID of the announcement file
to be replaced from the announcement
table by this file.rw INTEGER .1.3.6.1.4.1.1751.2.18.25.32 |
tasCmprsAnnceFilenameFile name for this announcement which is
to be compressed.rw DisplayString .1.3.6.1.4.1.1751.2.18.25.33 |
tasCmprsAnnceDescriptionDescription for this announcement which is to
to be compressed.rw DisplayString .1.3.6.1.4.1.1751.2.18.25.34 |
tasCmprsAnnceCmprsTypeThe type of compression used for
storing this announcement.rw Enumeration .1.3.6.1.4.1.1751.2.18.25.35 |
tasCmprsAnnceTypeThe type of this announcement.rw Enumeration .1.3.6.1.4.1.1751.2.18.25.36 |
tasCmprsAnnceIntfIndexInterface index in SSPPCCC format of TASM
card on which this announcement is to be
compressed.rw IntfIndex .1.3.6.1.4.1.1751.2.18.25.37 |
tasCmprsActionAction to be performed on this announcement.rw Enumeration .1.3.6.1.4.1.1751.2.18.25.38 |
tasTstAnnceIdAnnouncement ID to be played for testing.rw INTEGER .1.3.6.1.4.1.1751.2.18.25.39 |
tasTstAnnceIntfIndexInterface index in SSPPCCC format of
CE card on which this announcement
is to be played for testing.rw IntfIndex .1.3.6.1.4.1.1751.2.18.25.40 |
tasTstAnnceLawTypeThe type of CE card towards which
this announcement is to be played.
A-Law is for E1 and U-Law is for DS1rw Enumeration .1.3.6.1.4.1.1751.2.18.25.41 |
tasTstAnnceActionAction to be performed on this announcement
for testing.rw Enumeration .1.3.6.1.4.1.1751.2.18.25.42 |
tasTstLineIdTest ID to be started for line testing.rw Integer32 .1.3.6.1.4.1.1751.2.18.25.43 |
tasTstLineIntfIndexInterface index in SSPPCCC format of
CE card on which this test is to be initiated.rw IntfIndex .1.3.6.1.4.1.1751.2.18.25.44 |
tasTstLineActionTest action to be performed.rw Enumeration .1.3.6.1.4.1.1751.2.18.25.45 |
tasMemIntfIndexInterface index in SSPPCCC format of TASM card on which
the memory is to be initialised.rw IntfIndex .1.3.6.1.4.1.1751.2.18.25.46 |
tasMemActionTest action to be performed.rw Enumeration .1.3.6.1.4.1.1751.2.18.25.47 |
toneAnnceIpAddressIP Address for announcement ftp server.rw IpAddress .1.3.6.1.4.1.1751.2.18.25.48 |
toneAnnceAccountNameftp account name for access to announcement
ftp server.rw DisplayString .1.3.6.1.4.1.1751.2.18.25.49 |
toneAnnceAccountPasswordftp account password for access to announcement ftp
server.rw DisplayString .1.3.6.1.4.1.1751.2.18.25.50 |
toneAnnceSourceFileannouncement file with complete path on the ftp
serverrw DisplayString .1.3.6.1.4.1.1751.2.18.25.51 |
toneAnnceDestinationFileThe announcementSourceFile will be renamed with
MS DOS file format and placed in the /scsi/announce
directory on the disk.rw DisplayString .1.3.6.1.4.1.1751.2.18.25.52 |
toneAnnceFtpStatusCurrent status of the ftp announcement download.
Status of the software announcement. noActivity
is the initial start state from boot-up. working
is set while ftp'ing the announcement.
The final state is one of doneSuccessfully,
doneWithError, or aborted, all self-explanatory.
It will stay in this state until re-boot or
starting an announcement. If the state is
doneWithError then announcementSwErrorStatus will
be set to reflect the type of error.ro Enumeration .1.3.6.1.4.1.1751.2.18.25.53 |
toneAnnceFtpErrorStatusThe result of the finish of the ftp software
announcement download.
Set to a value 3-21 if announcementSwCopyStatus is
doneWithError. Set to none if
announcementFtpCopyStatus
is doneSuccessfully. Set to userAbort if
announcementSwCopyStatus is aborted.ro Enumeration .1.3.6.1.4.1.1751.2.18.25.54 |
toneAnnceFtpActionstart ftp announcement files. When
announcementFtpCopyStatus is working, the start
request will be ignored. Abort will have effect
only when announcementFtpCopystatus is working.rw Enumeration .1.3.6.1.4.1.1751.2.18.25.55 |
gr303Config OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.26 |
gr303IgConfig OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.26.1 |
gr303IgConfigTableTable of GR303 group configuration SEQUENCE OF Gr303IgConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.1 |
gr303IgConfigEntryRow definition for GR303 group configuration Gr303IgConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.1.1 |
gr303IgIdThis is used as an index into GR303IG table which
recognizes GR303 Interface Group INTEGER .1.3.6.1.4.1.1751.2.18.26.1.1.1.1 |
gr303IgRowStatusGR303IG config entry row statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.26.1.1.1.2 |
gr303IgAdminStatusAdministrative status of the GR303IGrw Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.3 |
gr303IgPrimaryTMCChanIntfIdPrimary TMC channel Interface Id
in SSPPCCC formatrw IntfIndex .1.3.6.1.4.1.1751.2.18.26.1.1.1.4 |
gr303IgPrimaryEOCChanIntfIdPrimary EOC channel Interface Id in
SSPPCCC formatrw IntfIndex .1.3.6.1.4.1.1751.2.18.26.1.1.1.5 |
gr303IgBackupTMCChanIntfIdBackup TMC channel Interface Id
in SSPPCCC formatrw IntfIndex .1.3.6.1.4.1.1751.2.18.26.1.1.1.6 |
gr303IgBackupEOCChanIntfIdBackup EOC channel Interface Id in
SSPPCCC formatrw IntfIndex .1.3.6.1.4.1.1751.2.18.26.1.1.1.7 |
gr303IgPrimaryTMCStatusPrimary TMC channel Statusro Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.8 |
gr303IgPrimaryEOCStatusPrimary EOC channel Statusro Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.9 |
gr303IgBackupTMCStatusBackup TMC channel Status.Value
null(5) Indicates that the Backup TMC has not
been configured.ro Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.10 |
gr303IgBackupEOCStatusBackup EOC channel Status.Value
null(5) Indicates that the Backup EOC has not
been configured.ro Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.11 |
gr303IgTMCProtSwitchProvStateLock/Unlock the protection switchrw Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.12 |
gr303IgEOCProtSwitchProvStateLock/Unlock the protection switchrw Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.13 |
gr303IgTMCProtSwitchCommandUser command to do path protection switchrw Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.14 |
gr303IgEOCProtSwitchCommandUser command to do path protection switchrw Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.15 |
gr303IgLocalDigitalSwitchTypeLDS (IDT) typerw Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.16 |
gr303IgLocalDigitalSwitchVersionLDS (IDT)Versionrw Enumeration .1.3.6.1.4.1.1751.2.18.26.1.1.1.17 |
gr303IgIntfConfigTableTable of interface attributes in an GR303IG SEQUENCE OF Gr303IgIntfConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.2 |
gr303IgIntfConfigEntryRow definition for GR303 Access Arrangement Interface configuration Gr303IgIntfConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.2.1 |
gr303IntfIgIdThis is used as an index into GR303Ig table which
recognizes GR303 Interface Group. This is used as a first
index into this interface table. INTEGER .1.3.6.1.4.1.1751.2.18.26.1.2.1.1 |
gr303IgIntfIdThis is used as an index into IG interface table
which recognizes GR303 Ig interfaces. This is used as a
second index into this table INTEGER .1.3.6.1.4.1.1751.2.18.26.1.2.1.2 |
gr303IgIntfPhysIdInterface's Physical ID (SSPPCCC)rw Integer32 .1.3.6.1.4.1.1751.2.18.26.1.2.1.3 |
gr303IgIntfNetIdgr303Ig Interface (DS1) Net Id assigned by the networkro Integer32 .1.3.6.1.4.1.1751.2.18.26.1.2.1.4 |
gr303IgIntfRowStatusGR303IG interface entry row status - row status can not be made
active until all the values are setrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.26.1.2.1.5 |
gr303LapdConfigTableTable of LAPD attributes in an GR303IG SEQUENCE OF Gr303LapdConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.4 |
gr303LapdConfigEntryRow definition for LAPD attributes in a GR303IG Gr303LapdConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.4.1 |
gr303LapdIgIdGR303IG Number index which recognizes GR303
Interface group INTEGER .1.3.6.1.4.1.1751.2.18.26.1.4.1.1 |
gr303T200value of Lapd T200 timer in miliseconds in step
size of 50 msrw INTEGER .1.3.6.1.4.1.1751.2.18.26.1.4.1.2 |
gr303T203value of Lapd T203 timer in secondsrw INTEGER .1.3.6.1.4.1.1751.2.18.26.1.4.1.3 |
gr303N200Maximum number of retransmissionsrw INTEGER .1.3.6.1.4.1.1751.2.18.26.1.4.1.4 |
gr303KMaximum number of outstanding I frames -
Lapd - window size.rw INTEGER .1.3.6.1.4.1.1751.2.18.26.1.4.1.5 |
gr303TMCConfigTableTable of Layer 3 attributes in an GR303IG SEQUENCE OF Gr303TMCConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.5 |
gr303TMCConfigEntryRow definition for GR303 Access Arrangement
Layer3 parameters configuration Gr303TMCConfigEntry .1.3.6.1.4.1.1751.2.18.26.1.5.1 |
gr303TMCIgIdGR303IG Number index which recognizes GR303
Interface group INTEGER .1.3.6.1.4.1.1751.2.18.26.1.5.1.1 |
gr303TMCT303value of TMC T303 timer in miliseconds with a
step size of 500 msrw INTEGER .1.3.6.1.4.1.1751.2.18.26.1.5.1.2 |
gr303TMCT396value of TMC T396 timer in miliseconds with a
step size of 1000 msrw INTEGER .1.3.6.1.4.1.1751.2.18.26.1.5.1.3 |
gr303Stats OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.27 |
gr303IgStats OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.27.1 |
gr303IgStatsTableTable of GR303 GR303IG based stats attributes SEQUENCE OF Gr303IgStatsEntry .1.3.6.1.4.1.1751.2.18.27.1.1 |
gr303IgStatsEntryRow definition for GR303 GR303IG based stats Gr303IgStatsEntry .1.3.6.1.4.1.1751.2.18.27.1.1.1 |
gr303IgStatsIgIdThis is used as an index into GR303 Ig
table which recognizes GR303 Interface Group
Interface group INTEGER .1.3.6.1.4.1.1751.2.18.27.1.1.1.1 |
gr303IgStatsCurrentInCallsTotal number of Currently
established incoming callsro Integer32 .1.3.6.1.4.1.1751.2.18.27.1.1.1.2 |
gr303IgStatsCurrentOutCallsTotal number of Currently
established outgoing callsro Integer32 .1.3.6.1.4.1.1751.2.18.27.1.1.1.3 |
gr303IgStatsOutCallSuccessfulTotal number successful
outgoing callsro Integer32 .1.3.6.1.4.1.1751.2.18.27.1.1.1.4 |
gr303IgStatsOutCallFailedTotal number of Failed
outgoing callsro Integer32 .1.3.6.1.4.1.1751.2.18.27.1.1.1.5 |
gr303IgStatsInCallSuccessfulTotal number successful
incoming callsro Integer32 .1.3.6.1.4.1.1751.2.18.27.1.1.1.6 |
gr303IgStatsInCallFailedTotal number of Failed
incoming callsro Integer32 .1.3.6.1.4.1.1751.2.18.27.1.1.1.7 |
gr303IgStatsResetgr303Ig reset statistics
buttonrw Enumeration .1.3.6.1.4.1.1751.2.18.27.1.1.1.8 |
atmTrunkingMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.28 |
atmTrunkingIWFBaseGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.28.1 |
atmTrunkingIWFIdentifierIWF ID for the local endpointrw Integer32 .1.3.6.1.4.1.1751.2.18.28.1.1 |
atmTrunkingIWFLocalAddressIWF ATM address for the local endpointrw OCTET STRING .1.3.6.1.4.1.1751.2.18.28.1.2 |
atmTrunkingIWFMaxRemoteIWFMaximum remote IWF that can connect to this endpointrw Integer32 .1.3.6.1.4.1.1751.2.18.28.1.3 |
atmTrunkingIWFAdminStatusIndicates whether the Local IWF is active or notrw Enumeration .1.3.6.1.4.1.1751.2.18.28.1.4 |
atmTrunkingRemoteIWFTableRemote IWF table SEQUENCE OF AtmTrunkingRemoteIWFEntry .1.3.6.1.4.1.1751.2.18.28.2 |
atmTrunkingRemoteIWFEntryEntry in atmTrunkingRemoteIWFTable AtmTrunkingRemoteIWFEntry .1.3.6.1.4.1.1751.2.18.28.2.1 |
atmTrunkingRemoteIWFIdentifierIWF ID for the remote IWF Integer32 .1.3.6.1.4.1.1751.2.18.28.2.1.1 |
atmTrunkingRemoteIWFAddressIWF ATM address for the remote IWFrw OCTET STRING .1.3.6.1.4.1.1751.2.18.28.2.1.2 |
atmTrunkingRemoteIWFTrnkModeMaximum remote IWF that can connect to this endpointrw Enumeration .1.3.6.1.4.1.1751.2.18.28.2.1.3 |
atmTrunkingRemoteIWFAdminStatusIndicates whether the Local IWF is active or notrw Enumeration .1.3.6.1.4.1.1751.2.18.28.2.1.4 |
atmTrunkingRemoteIWFRowStatusMaximum remote IWF that can connect to this endpointrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.28.2.1.5 |
atmTrunkingSigVccTableTable of iwf signaling vcc configuration entities SEQUENCE OF AtmTrunkingSigVccEntry .1.3.6.1.4.1.1751.2.18.28.3 |
atmTrunkingSigVccEntryEntry in atmTrunkingSigVccTable AtmTrunkingSigVccEntry .1.3.6.1.4.1.1751.2.18.28.3.1 |
atmTrunkingSigVccRmtIWFIdentifierIWF ID for the remote IWF Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.1 |
atmTrunkingSigVccIdentifierVcc ID assigned by the owner of this signaling Vcc INTEGER .1.3.6.1.4.1.1751.2.18.28.3.1.2 |
atmTrunkingSigVccOutgoingIfIndexIntf index of the outgoing interface,readonly for SVC/SPVCrw IntfIndex .1.3.6.1.4.1.1751.2.18.28.3.1.3 |
atmTrunkingSigVccOutgoingVpiVPI used at the outgoing interface, readonly for SVC/SPVCrw INTEGER .1.3.6.1.4.1.1751.2.18.28.3.1.4 |
atmTrunkingSigVccOutgoingVciVCI used at the outgoing interface, readonly for SVC/SPVCrw INTEGER .1.3.6.1.4.1.1751.2.18.28.3.1.5 |
atmTrunkingSigVccOwnerIndicates who is the owner of the Sig VCCrw Enumeration .1.3.6.1.4.1.1751.2.18.28.3.1.6 |
atmTrunkingSigVccInactiveTimerInactive time period on which to clear the callrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.7 |
atmTrunkingSigVccTypeIndicates if the SigVcc should be setup as PVC/SPVC/SVCrw Enumeration .1.3.6.1.4.1.1751.2.18.28.3.1.8 |
atmTrunkingSigVccSignalingIndicates the signalling protocol used between the IWFsrw Enumeration .1.3.6.1.4.1.1751.2.18.28.3.1.9 |
atmTrunkingSigVccFwPcr01Forward PCR for the callrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.10 |
atmTrunkingSigVccBwPcr01Backward PCR for the callrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.11 |
atmTrunkingSigVccFwScr01Forward SCR for the callrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.12 |
atmTrunkingSigVccBwScr01Backward SCR for the callrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.13 |
atmTrunkingSigVccFwMbs01Forward MBS for the callrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.14 |
atmTrunkingSigVccBwMbs01Backward MBS for the callrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.15 |
atmTrunkingSigVccMaxAal2VccMaximum number of bearer VCCs controlled by this SigVccrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.16 |
atmTrunkingSigVccActiveAal2VccNumber of active bearer VCCs controlled by this SigVccro Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.17 |
atmTrunkingSigVccOperStatusIndicates whether the Local IWF is active or notro Enumeration .1.3.6.1.4.1.1751.2.18.28.3.1.18 |
atmTrunkingSigVccRowStatusRow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.28.3.1.19 |
atmTrunkingSigVccViBVI to associate the Egress part of A2B connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.28.3.1.20 |
atmTrunkingSigVccVUNIBVUNI associated the Egress part of A2B connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.28.3.1.21 |
atmTrunkingSigVccRetryTimerthe time(seconds) to wait before attempting to establish
the ATM Trunking Signalling VCC SPVC after previous failed
call attempt. 0 indicates retries will be attempted immedi
atelyrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.22 |
atmTrunkingSigVccRetryLimitATM Trunking Signalling VCC SPVC Retry Limit.
0 indicates unlimitedrw Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.23 |
atmTrunkingSigVccRestartThe active ATM Trunking SPVC is released, if necessary,
and a new setup procedure is begun if restart,
otherwise, noop.rw Enumeration .1.3.6.1.4.1.1751.2.18.28.3.1.24 |
atmTrunkingSigVccPriorityPriority of TrunkingSigVcc - priority-1 being highest priority .rw Enumeration .1.3.6.1.4.1.1751.2.18.28.3.1.25 |
atmTrunkingSigVccRetryCounterIndicates how many attempts to establish the
connection have failed. It is reset whenever a
connection is successfully established or the SigVcc SPVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.28.3.1.26 |
atmTrunkingBrVccConfigTableTable of iwf aal2 bearer vcci configuration
entities SEQUENCE OF AtmTrunkingBrVccConfigEntry .1.3.6.1.4.1.1751.2.18.28.4 |
atmTrunkingBrVccConfigEntryRow definition for iwf aal2 vcci configuration AtmTrunkingBrVccConfigEntry .1.3.6.1.4.1.1751.2.18.28.4.1 |
atmTrunkingBrVccRmtIWFIdIWF ID for the remote IWF Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.1 |
atmTrunkingBrVccSigVccIdSignalling Vcc associated with this Br Vccro INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.2 |
atmTrunkingBrVccIdId of the AAL2 Bear Vcc INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.3 |
atmTrunkingBrVccIfIntf index of the outgoing interface,
readonly for SVC/SPVCrw IntfIndex .1.3.6.1.4.1.1751.2.18.28.4.1.4 |
atmTrunkingBrVccVpiVPI value of this VCC connection.
Valid range is a number between 0 and 4095.rw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.5 |
atmTrunkingBrVccVciVCI value of this VCC connection.
Valid range is a number between 0 and 65535.rw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.6 |
atmTrunkingBrVccViBVI to associate the Egress part of A2B connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.7 |
atmTrunkingBrVccVUNIBVUNI associated the Egress part of A2B connectionrw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.8 |
atmTrunkingBrVccServiceTypeservice typerw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.9 |
atmTrunkingBrVccSarTypesar typerw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.10 |
atmTrunkingBrVccOwnerThe owner of this Vccrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.11 |
atmTrunkingBrVccOperStatusThe Operational Status of this Bearer Vccro Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.12 |
atmTrunkingBrVccFwAtmPcr01Forward pcr (0+1)rw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.13 |
atmTrunkingBrVccBwAtmPcr01Backward pcr (0+1)rw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.14 |
atmTrunkingBrVccFwAtmScr01Forward scr (0+1)rw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.15 |
atmTrunkingBrVccBwAtmScr01Backward scr (0+1)rw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.16 |
atmTrunkingBrVccFwAtmMbs01Forward Mbs (0+1)rw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.17 |
atmTrunkingBrVccBwAtmMbs01Backward Mbs (0+1)rw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.18 |
atmTrunkingBrVccConnTypeconnection typerw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.19 |
atmTrunkingBrVccActiveChanCntNumber of currently active channels in this Vccro Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.20 |
atmTrunkingBrVccMaxAal2ChanIdMax Id of channels supported within this br vccrw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.21 |
atmTrunkingBrVccCircuitModeDataSuppCircuit mode datarw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.22 |
atmTrunkingBrVccFrameModeSuppFrame mode datarw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.23 |
atmTrunkingBrVccFaxModSuppFAX Demodulationrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.24 |
atmTrunkingBrVccCASPktXportSuppChannel Associated Signalingrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.25 |
atmTrunkingBrVccDTMFPktXportSuppDTMF Dialed Digitsrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.26 |
atmTrunkingBrVccMFR1PktXportSuppMF-R1 Dialed Digitsrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.27 |
atmTrunkingBrVccMFR2PktXportSuppMF-R2 Dialed Digitsrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.28 |
atmTrunkingBrVccPCMEncodingDTMF Dialed Digitsrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.29 |
atmTrunkingBrVccMaxFrameLengthMaximum length of frame mode datarw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.30 |
atmTrunkingBrVccIdleChannSuprSuppIdle Channel Supressionrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.31 |
atmTrunkingBrVccSilenceDetSuppSilence Detectionrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.32 |
atmTrunkingBrVccCompressionSpecCompression Typerw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.33 |
atmTrunkingBrVccAudioProfileSourceProfile Sourcerw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.34 |
atmTrunkingBrVccAudioProfileIdProfile IDrw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.35 |
atmTrunkingBrVccAvailBwAvailable Bandwidth left in this Vccro Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.36 |
atmTrunkingBrVccRowStatusRow statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.28.4.1.37 |
atmTrunkingBrVccGr303SuppGR303 Supportrw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.38 |
atmTrunkingBrVccOamStatusIndicates the OAM monitoring status of side A.
The 2 possible states are:
Unsupp: No monitoring enabled.
End-Pt: Atm side is only an end point, therefore
it will respond to AIS/RDI.rw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.39 |
atmTrunkingBrVccInactiveTimerThe time(in seconds) to wait before releasing the
ATM Trunking Bearer VCC SVC after all narrow band
calls are droppedrw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.40 |
atmTrunkingBrVccRetryTimerthe time(seconds) to wait before attempting to establish
the ATM Trunking Bearer VCC SPVC after previous failed
call attempt. 0 indicates retries will be attempted
immediatelyrw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.41 |
atmTrunkingBrVccRetryLimitATM Trunking Bearer VCC SPVC Retry Limit. 0 indicates
unlimitedrw Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.42 |
atmTrunkingBrVccRestartThe active ATM Trunking BrVcc SPVC is released,
if necessary, and a
new setup procedure is begun if 'restart',
otherwise, noop.rw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.43 |
atmTrunkingBrVccCuTimerCuTimer represents combined use timer, is
set to zero such that every ATM cell
transmitted contains one, and only one,
AAL2 packet, and the first octet of the AAL2
packet header follows immediately after the Start
Field in the ATM cell payload. If the
AAL2 packet payload is less than 44 octets,
the remainder of the ATM cell payload
following the end of the AAL2 packet shall be
filled with zeros as padding.
Each increment of CuTimer means 5ms more to wait.
And cuTimer default value 4 means to wait 20ms
before the ATM cell is sent out.rw INTEGER .1.3.6.1.4.1.1751.2.18.28.4.1.44 |
atmTrunkingBrVccPriorityPriority of TrunkingBrVcc - priority-1 being highest priority .rw Enumeration .1.3.6.1.4.1.1751.2.18.28.4.1.45 |
atmTrunkingBrVccRetryCounterIndicates how many attempts to establish the
connection have failed. It is reset whenever a
connection is successfully established or the BrVcc SPVC
is restarted.ro Integer32 .1.3.6.1.4.1.1751.2.18.28.4.1.46 |
atmTrunkingDataChannelConfigTableTable of iwf aal2 data channel configuration
entities SEQUENCE OF AtmTrunkingDataChannelConfigEntry .1.3.6.1.4.1.1751.2.18.28.5 |
atmTrunkingDataChannelConfigEntryRow definition for iwf aal2 data channel
configuration AtmTrunkingDataChannelConfigEntry .1.3.6.1.4.1.1751.2.18.28.5.1 |
atmTrunkingDataChannelRmtIWFIdIWF ID for the remote IWF Integer32 .1.3.6.1.4.1.1751.2.18.28.5.1.1 |
atmTrunkingDataChannelSigVccIdVcc ID assigned by the owner of this signaling Vccro INTEGER .1.3.6.1.4.1.1751.2.18.28.5.1.2 |
atmTrunkingDataChannelBrVccIdId of the AAL2 Bear Vcc INTEGER .1.3.6.1.4.1.1751.2.18.28.5.1.3 |
atmTrunkingDataChannelIdThe AAL2 Channel Id of this channel INTEGER .1.3.6.1.4.1.1751.2.18.28.5.1.4 |
atmTrunkingDataChanOperStatusOperational Status of this channelro Enumeration .1.3.6.1.4.1.1751.2.18.28.5.1.5 |
atmTrunkingDataChanOwnerThe owner of this channelro Enumeration .1.3.6.1.4.1.1751.2.18.28.5.1.6 |
atmTrunkingDataChanNBIntfThe index of narrowband interface this channel
is mapped toro IntfIndex .1.3.6.1.4.1.1751.2.18.28.5.1.7 |
protectionGroup OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.29 |
protectionGroupTableTable of interface protection group
attributes SEQUENCE OF ProtectionGroupEntry .1.3.6.1.4.1.1751.2.18.29.1 |
protectionGroupEntryDefines one interface protection group ProtectionGroupEntry .1.3.6.1.4.1.1751.2.18.29.1.1 |
pgtGroupIda user selected logical number representing
a protection group uniquely within a PSAX Integer32 .1.3.6.1.4.1.1751.2.18.29.1.1.1 |
pgtSwitchoverMethodswitchover method to switch traffic from
failed primary interface to available standby interface. In
auto method, PSAX automatically switches the traffic
without user intervention. In manual method, a failed
primary does not switch traffic and gives control to user
to do so.rw Enumeration .1.3.6.1.4.1.1751.2.18.29.1.1.2 |
pgtSwitchbackMethodswitchback method to switch traffic
from a standby to its corresponding recovered primary
interface. In auto method, PSAX automatically
switches the traffic without user intervention. In
manual method, standby does not switch traffic and
gives control to user to do so.rw Enumeration .1.3.6.1.4.1.1751.2.18.29.1.1.3 |
h248Config OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.30 |
h248TermIdTableTable of H.248 Terminations SEQUENCE OF H248TermIdEntry .1.3.6.1.4.1.1751.2.18.30.1 |
h248TermIdEntryRow definition for H.248
Termination ID table H248TermIdEntry .1.3.6.1.4.1.1751.2.18.30.1.1 |
h248TermSlotIdSlot # for termination INTEGER ( 1..99 ) .1.3.6.1.4.1.1751.2.18.30.1.1.1 |
h248TermPhyPortIdPhysical Port # for termination INTEGER ( 0..999 ) .1.3.6.1.4.1.1751.2.18.30.1.1.2 |
h248TermLogPortIdLogical Port # for termination INTEGER ( 0..999 ) .1.3.6.1.4.1.1751.2.18.30.1.1.3 |
h248TermChanIdChan # for termination INTEGER ( 0..999 ) .1.3.6.1.4.1.1751.2.18.30.1.1.4 |
h248TermVpiVPI # for termination. Value 0 is
reserved to indicate N/A, e.g., TDM
termination. Thus, VPI = h248TermVpi - 1,
for h248TermVpi > 0. INTEGER ( 0..4096 ) .1.3.6.1.4.1.1751.2.18.30.1.1.5 |
h248TermVciVCI # for termination. Value 0 is
reserved to indicate N/A, e.g., TDM
termination. Thus, VCI = h248TermVci - 1,
for h248TermVci > 0. INTEGER ( 0..65536 ) .1.3.6.1.4.1.1751.2.18.30.1.1.6 |
h248TermIdTermination ID is provisioned
by user and used for identifying termination
between MGC and MGrw OCTET STRING .1.3.6.1.4.1.1751.2.18.30.1.1.7 |
h248TermAal2CidAAL2 CIDrw INTEGER .1.3.6.1.4.1.1751.2.18.30.1.1.8 |
h248TermActivationActivation for termination IDrw Enumeration .1.3.6.1.4.1.1751.2.18.30.1.1.9 |
h248TermRowStatush248TermIdEntry row statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1751.2.18.30.1.1.10 |
h248SysControl OBJECT IDENTIFIER .1.3.6.1.4.1.1751.2.18.31 |
h248MaxNumberOfContextsThe value of the property gives the
maximum number of contexts that can exist at
anytime. The NULL context is not included
in this number.rw Integer32 .1.3.6.1.4.1.1751.2.18.31.1 |
h248MaxTerminationsPerContextThe max number of terminations allowed
in a context.rw Integer32 .1.3.6.1.4.1.1751.2.18.31.2 |
h248NormalMGExecutionTimeSettable by the MGC to indicate the
interval within which the MGC expects
a response to any transaction from the MG
(exclusive of the network delay). Value
represents milliseconds.rw Integer32 .1.3.6.1.4.1.1751.2.18.31.3 |
h248NormalMGCExecutionTimeSettable by the MGC to indicate the
interval within which the MG expects
a response to any transaction from the MG
(exclusive of the network delay). Value
represents milliseconds.rw Integer32 .1.3.6.1.4.1.1751.2.18.31.4 |
h248MGProvisionalResponseTimerValueIndicates the time within which the MGC should expect
a Pending Response from the MG if a Transaction can not be
completed. Initially set to h248NormalMGExecutionTime,
plus network delay, but maybe lowered. Value represents
milliseconds.rw Integer32 .1.3.6.1.4.1.1751.2.18.31.5 |
h248MGCProvisionalResponseTimerValueIndicates the time within which the MG should expect
a Pending Response from the MGC if a Transaction can not be
completed. Initially set to h248NormalMGCExecutionTime,
plus network delay, but maybe lowered. Value represents
milliseconds.rw Integer32 .1.3.6.1.4.1.1751.2.18.31.6 |
h248MGCIpAddress1The IP address of the 1st MGC.rw IpAddress .1.3.6.1.4.1.1751.2.18.31.7 |
h248MGCIpAddress2The IP address of the 2nd MGC.rw IpAddress .1.3.6.1.4.1.1751.2.18.31.8 |