DPW-ATM-MIB
AI MIB Summary
The DPW-ATM-MIB module provides configuration and statistical monitoring for Pseudo-Wire emulations of Asynchronous Transfer Mode (ATM) traffic over Packet Switched Networks. It tracks specific ATM PW session states, error counters, and performance metrics required to validate the integrity of ATM cell transport across IP-based infrastructure.
This MIB contains managed object definitions for Pseudo Wire emulation of ATM over Packet Switched Networks (PSN).
This MIB supplements the PW-STD-MIB module. The PW-STD-MIB contains structures and MIB associations generic to Pseudo-Wire (PW) emulation. PW-specific MIBs (such as this) contain config and stats for specific PW types.
Copyright (C) The IETF Trust (2008). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices.
Main OID:
dpwAtmMIB.mplsATMPWMIB.1
101
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
101 total| Object Name |
|---|
dpwAtmMIBThis MIB contains managed object definitions for
Pseudo Wire emulation of ATM over Packet Switched
Networks (PSN).
This MIB supplements the PW-STD-MIB module.
The PW-STD-MIB contains structures and MIB associations
generic to Pseudo-Wire (PW) emulation. PW-specific
MIBs (such as this) contain config and stats for specific
PW types.
Copyright (C) The IETF Trust (2008). This version of
this MIB module is part of RFC XXXX; see the RFC itself for
full legal notices. MODULE-IDENTITY .mplsATMPWMIB.1 |
dpwAtmNotifications OBJECT IDENTIFIER .mplsATMPWMIB.1.0 |
dpwAtmObjects OBJECT IDENTIFIER .mplsATMPWMIB.1.1 |
dpwAtmCfgTableThis table specifies generic information for an ATM PW
to be carried over PSN in any mode. SEQUENCE OF DpwAtmCfgEntry .mplsATMPWMIB.1.1.1 |
dpwAtmCfgEntryThis table contains a set of parameters for
the ATM PW that needs to be adapted and carried
over PSN. This table is indexed by pwIndex from
pwTable. An entry is created for every newly pwIndex
in the pwTable. Unless otherwise specified, all
read-write objects in this table MAY
be changed when the PW is defined as not active
and all RW objects values must persist
after reboot DpwAtmCfgEntry .mplsATMPWMIB.1.1.1.1 |
dpwAtmCfgMaxCellConcatenationThe maximum number of ATM cells that can be
concatenated into one PW packet towards PSN.
In non LDP or other signaling protocol environment,
this object MAY be changed at anytime, but traffic
might be interuppted, otherwise, it may be changed
when PW is not active.rw Unsigned32 .mplsATMPWMIB.1.1.1.1.1 |
dpwAtmCfgFarEndMaxCellConcatenationThe maximum number of ATM cells that can be
concatenated into one PW packet towards PSN as reported by
the far end. If no LDP in use, the object will either
return value 0 or allow setting it for calculating
protocol overhead.ro Unsigned32 .mplsATMPWMIB.1.1.1.1.2 |
dpwAtmCfgTimeoutModeThis objects determines whether a packet can be
transmitted to the PSN based on time out expiration
for collecting cells or not. The actual handling of the
time out is implementation specific-as such this object
may be changed at any time under proper consideration of
traffic interupption effect.rw Enumeration .mplsATMPWMIB.1.1.1.1.3 |
dpwAtmMaxCellConcatenationTimerThis timer is used to concatenate the maximum ATM cell
packets in the configured timer value. The unit of the
timer is in microseconds.rw Unsigned32 .mplsATMPWMIB.1.1.1.1.4 |
dpwAtmOutboundNto1TableThis table specifies the information for an ATM PW to
be carried over PSN in the outbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following: atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3). SEQUENCE OF DpwAtmOutboundNto1Entry .mplsATMPWMIB.1.1.2 |
dpwAtmOutboundNto1EntryA row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all read-create objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot. DpwAtmOutboundNto1Entry .mplsATMPWMIB.1.1.2.1 |
dpwAtmOutboundNto1AtmIfThe ATM Interface that receives cells from the ATM network. InterfaceIndex (IF-MIB) .mplsATMPWMIB.1.1.2.1.1 |
dpwAtmOutboundNto1VpiVPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF AtmVpIdentifier (ATM-TC-MIB) .mplsATMPWMIB.1.1.2.1.2 |
dpwAtmOutboundNto1RowStatusThis Object is used to create, modify or delete a row in
this table.rw RowStatus (SNMPv2-TC) .mplsATMPWMIB.1.1.2.1.3 |
dpwAtmOutboundNto1MappedVpiThe egress generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not activerw Enumeration .mplsATMPWMIB.1.1.2.1.4 |
dpwAtmOutboundNto1OntIdThis object specifies the identification of an ONT.rw OCTET STRING .mplsATMPWMIB.1.1.2.1.5 |
dpwAtmInboundNto1TableThis table specifies the information for an ATM PW to
be carried over PSN in the Inbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following:atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3). SEQUENCE OF DpwAtmInboundNto1Entry .mplsATMPWMIB.1.1.3 |
dpwAtmInboundNto1EntryA row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all Read-Creat objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot. DpwAtmInboundNto1Entry .mplsATMPWMIB.1.1.3.1 |
dpwAtmInboundNto1AtmIfThe ATM Interface that receives cells from the ATM network. InterfaceIndex (IF-MIB) .mplsATMPWMIB.1.1.3.1.1 |
dpwAtmInboundNto1VpiVPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF. AtmVpIdentifier (ATM-TC-MIB) .mplsATMPWMIB.1.1.3.1.2 |
dpwAtmInboundNto1RowStatusThis Object is used to modify or delete a row in
this table. This table is associated with dpwAtmOutboundNto1Table.
So a row can be created in this table through dpwAtmOutboundNto1Tablerw RowStatus (SNMPv2-TC) .mplsATMPWMIB.1.1.3.1.3 |
dpwAtmInboundNto1MappedVpiThe generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not active.rw Enumeration .mplsATMPWMIB.1.1.3.1.4 |
dpwAtmVciExpTableThis table contains the ONT downstream VCI-EXP qos mapping
parameters. This exp value represents the queue-type in
exp-queue table SEQUENCE OF DpwAtmVciExpEntry .mplsATMPWMIB.1.1.4 |
dpwAtmVciExpEntryAn entry in this table is created for downstream ont qos. DpwAtmVciExpEntry .mplsATMPWMIB.1.1.4.1 |
dpwAtmOntidThis object represents the identification of an ONT.rw Unsigned32 .mplsATMPWMIB.1.1.4.1.1 |
dpwAtmVpiThis object represents the downstream ont qos vpi value.rw Unsigned32 .mplsATMPWMIB.1.1.4.1.2 |
dpwAtmExpVciThe downstream ont qos vci value for corresponding vpi.rw Unsigned32 .mplsATMPWMIB.1.1.4.1.3 |
dpwAtmVciExpThe exp value representing exp-queue table for downstream ont qos.rw Unsigned32 .mplsATMPWMIB.1.1.4.1.4 |
dpwAtmExpRowStatusThis vci-exp table supports only exp value modification. This object becomes active
with default exp value when vci-qos table entries are created. This Object is
for internal use only and not configurable by user.rw Unsigned32 .mplsATMPWMIB.1.1.4.1.5 |
dpwAtmExpQosTableThis table contains the downstream ont qos EXP Queue related parameters. SEQUENCE OF DpwAtmExpQosEntry .mplsATMPWMIB.1.1.5 |
dpwAtmExpQosEntryAn entry in this table is created for downstream ont qos with queue-type
for corresponfing exp . DpwAtmExpQosEntry .mplsATMPWMIB.1.1.5.1 |
dpwAtmQosExpThis object specifies the exp value corresponding to downstream ont qos.rw Unsigned32 .mplsATMPWMIB.1.1.5.1.1 |
dpwAtmExpQosModeThis obejct specifies the exp queue-type for downstream ont qos .rw Unsigned32 .mplsATMPWMIB.1.1.5.1.2 |
dpwAtmExpQosPriorityThis object specifes the priority for queue-type of strict priority(SP).rw Unsigned32 .mplsATMPWMIB.1.1.5.1.3 |
dpwAtmExpQosWeightThis object specifies the weight for queue-type of weighted round robin(WRR).rw Unsigned32 .mplsATMPWMIB.1.1.5.1.4 |
dpwAtmExpQosRowStatusThis Object is for internal use only and not configurable by user. This table will
have default values unless modified by the user.rw Unsigned32 .mplsATMPWMIB.1.1.5.1.5 |
dpwAtmVciQosTableThis table contains VCI Queue related parameters for upstream ont qos. SEQUENCE OF DpwAtmVciQosEntry .mplsATMPWMIB.1.1.6 |
dpwAtmVciQosEntryAn entry in this table is created for upstream ont qos vci-qos. DpwAtmVciQosEntry .mplsATMPWMIB.1.1.6.1 |
dpwAtmVciQosClassThis objects specifies class type for upstream ont qos vci.rw INTEGER .mplsATMPWMIB.1.1.6.1.1 |
dpwAtmVciQosPCRThis object specifies the peak cell rate for corresponding upstream ont qos.This value
should be in a multiples of 151 onlyrw Unsigned32 .mplsATMPWMIB.1.1.6.1.2 |
dpwAtmVciQosSCRThis object specifies the substainable cell rate for upstream ont qos.This value
should be in a multiples of 151 onlyrw Unsigned32 .mplsATMPWMIB.1.1.6.1.3 |
dpwAtmVciQosMBSThis object specifies maximum burst size of corresponding vci in upstream ont qos.rw Unsigned32 .mplsATMPWMIB.1.1.6.1.4 |
dpwAtmVciQosCDVTThis object specifies cell delay variance tolerance corresponds to vci in upstream ont qos.rw Unsigned32 .mplsATMPWMIB.1.1.6.1.5 |
dpwAtmVciQosRowStatusThis Object is used to create and delete a row in this table.
When the Row status is active, whenever user configures in OLT, ONT is also configured.
For row creation, user is suggested to configure the qos parameters after configuring rowstatus
to create and wait. Then make the row status active. Creation or deletion of vci-qos table
automatically creates/deletes vci-exp table.rw Unsigned32 .mplsATMPWMIB.1.1.6.1.6 |
dpwAtmPerfCurrentTableThe current 15 minute interval counts are in
this table.
This table provides performance information per ATM PW. SEQUENCE OF DpwAtmPerfCurrentEntry .mplsATMPWMIB.1.1.7 |
dpwAtmPerfCurrentEntryAn entry in this table is created by the agent for every
pwAtmCfgTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwAtmPerfInterval table and the counts in this entry
are reset to zero. DpwAtmPerfCurrentEntry .mplsATMPWMIB.1.1.7.1 |
dpwAtmPerfCurrentMissingPktsNumber of missing packets (as detected via control word
sequence number gaps).ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.1 |
dpwAtmPerfCurrentPktsReOrderNumber of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this Feature.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.2 |
dpwAtmPerfCurrentPktsMisOrderNumber of packets detected out of order (via control word
sequence numbers).ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.3 |
dpwAtmPerfCurrentPktsTimeoutNumber of packets transmitted due to timeout expiration
while attempting to collect cells.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.4 |
dpwAtmPerfCurrentCellsXmitNumber of transmitted cells.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.5 |
dpwAtmPerfCurrentCellsDroppedNumber of dropped cells.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.6 |
dpwAtmPerfCurrentCellsReceivedNumber of received cells.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.7 |
dpwAtmPerfCurrentUnknownCellsNumber of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.7.1.8 |
dpwAtmPerfIntervalTableThis table provides performance information per ATM PW
similar to the pwAtmPerfCurrentTable above. However,
these counts represent historical 15 minute intervals.
Typically, this table will have a maximum of 96 entries
for a 24 hour period. SEQUENCE OF DpwAtmPerfIntervalEntry .mplsATMPWMIB.1.1.8 |
dpwAtmPerfIntervalEntryAn entry in this table is created by the agent for
every pwAtmPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to zero for the next current 15 minute interval. DpwAtmPerfIntervalEntry .mplsATMPWMIB.1.1.8.1 |
dpwAtmPerfIntervalNumberA number (normally between 1 and 96 to cover a 24 hour
period) which identifies the interval for which the set
of statistics is available. The interval identified by 1
is the most recently completed 15 minute interval, and
the interval identified by N is the interval immediately
preceding the one identified by N-1. The minimum range of
N is 1 through 4. The default range is 1 through 32. The
maximum value of N is 96. Unsigned32 .mplsATMPWMIB.1.1.8.1.1 |
dpwAtmPerfIntervalValidDataThis variable indicates if the data for this interval
is valid.ro TruthValue (SNMPv2-TC) .mplsATMPWMIB.1.1.8.1.2 |
dpwAtmPerfIntervalDurationThe duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided.ro Unsigned32 .mplsATMPWMIB.1.1.8.1.3 |
dpwAtmPerfIntervalMissingPktsNumber of missing packets (as detected via control
word sequence number gaps).ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.4 |
dpwAtmPerfIntervalPktsReOrderNumber of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
Feature.ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.5 |
dpwAtmPerfIntervalPktsMisOrderNumber of packets detected out of order (via control word
sequence numbers).ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.6 |
dpwAtmPerfIntervalPktsTimeoutNumber of packets transmitted due to timeout expiration.ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.7 |
dpwAtmPerfIntervalCellsXmitNumber of transmitted cells.ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.8 |
dpwAtmPerfIntervalCellsDroppedNumber of dropped cells.ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.9 |
dpwAtmPerfIntervalCellsReceivedNumber of received cells.ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.10 |
dpwAtmPerfIntervalUnknownCellsNumber of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode.ro PerfIntervalCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.8.1.11 |
dpwAtmPerfIntervalTimeTimestamp value of the system in hours, minutes and seconds
when data is received for particular pseudo-wire for every
15-minutesro OCTET STRING .mplsATMPWMIB.1.1.8.1.12 |
dpwAtmPerf1DayIntervalTableThis table provides performance information per ATM PW
similar to the pwAtmPerfIntervalTable above. However,
these counters represent historical 1 day intervals up to
one full month. SEQUENCE OF DpwAtmPerf1DayIntervalEntry .mplsATMPWMIB.1.1.9 |
dpwAtmPerf1DayIntervalEntryAn entry is created in this table by the agent
for every entry in the pwAtmCfgTable table. DpwAtmPerf1DayIntervalEntry .mplsATMPWMIB.1.1.9.1 |
dpwAtmPerf1DayIntervalNumberThe number of interval, where 1 indicates current day
measured period and 2 and above indicate previous days
respectively Unsigned32 .mplsATMPWMIB.1.1.9.1.1 |
dpwAtmPerf1DayIntervalValidDataThis object indicates if the data for this interval
is valid.ro TruthValue (SNMPv2-TC) .mplsATMPWMIB.1.1.9.1.2 |
dpwAtmPerf1DayIntervalDurationThe duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided.ro Unsigned32 .mplsATMPWMIB.1.1.9.1.3 |
dpwAtmPerf1DayIntervalMissingPktsNumber of missing packets (as detected via control word
sequence number gaps).ro Counter32 .mplsATMPWMIB.1.1.9.1.4 |
dpwAtmPerf1DayIntervalPktsReOrderNumber of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
feature.ro Counter32 .mplsATMPWMIB.1.1.9.1.5 |
dpwAtmPerf1DayIntervalPktsMisOrderNumber of packets detected out of order(via control word
sequence numbers), and could not be re-ordered.ro Counter32 .mplsATMPWMIB.1.1.9.1.6 |
dpwAtmPerf1DayIntervalPktsTimeoutNumber of packets transmitted due to timeout expiration.ro Counter32 .mplsATMPWMIB.1.1.9.1.7 |
dpwAtmPerf1DayIntervalCellsXmitNumber of transmitted cells.ro Counter32 .mplsATMPWMIB.1.1.9.1.8 |
dpwAtmPerf1DayIntervalCellsDroppedNumber of dropped cells.ro Counter32 .mplsATMPWMIB.1.1.9.1.9 |
dpwAtmPerf1DayIntervalCellsReceivedNumber of received cells.ro Counter32 .mplsATMPWMIB.1.1.9.1.10 |
dpwAtmPerf1DayIntervalUnknownCellsNumber of cells received from the PSN with unknown VPI
or VCI value. This object is relevant only in N:1 mode.ro Counter32 .mplsATMPWMIB.1.1.9.1.11 |
dpwAtmPerf1DayIntervalTimeTimestamp value of the system in hours, minutes and seconds
when data is received for particular pseudo-wire for every
dayro OCTET STRING .mplsATMPWMIB.1.1.9.1.12 |
dpwOamTableThis table specifies to enable/disable OAM
on the PW associated to the specified pwIndex.
It also shows the defects of the PW OAM. SEQUENCE OF DpwOamEntry .mplsATMPWMIB.1.1.10 |
dpwOamEntryThis table is indexed by pwIndex.
Unless otherwise specified, all read-create
objects in this table MUST NOT be changed
after row activation and SHOULD remain
unchanged after reboot. DpwOamEntry .mplsATMPWMIB.1.1.10.1 |
dpwOamEnableThis variable indicates if OAM is enabled for this PW.
It MAY be changed at any time.rw TruthValue (SNMPv2-TC) .mplsATMPWMIB.1.1.10.1.1 |
dpwOamDefectThis specifies the defect states of PW OAMro INTEGER .mplsATMPWMIB.1.1.10.1.2 |
dpwOamRowStatusFor creating, modifying, and deleting this row. None of the
read-create objects in the conceptual rows may be changed
when this object is in the active(1) state.rw RowStatus (SNMPv2-TC) .mplsATMPWMIB.1.1.10.1.3 |
dpwAtmoamTableThis table specifies to enable/disable CC Generation and also
to set the Flow Type as E2E / SEG. SEQUENCE OF DpwAtmoamEntry .mplsATMPWMIB.1.1.11 |
dpwAtmoamEntryThis table is indexed by pwIndex.
Unless otherwise specified, all read-create
objects in this table MUST NOT be changed
after row activation and SHOULD remain
unchanged after reboot. DpwAtmoamEntry .mplsATMPWMIB.1.1.11.1 |
dpwCcStatusThis variable is used to enable / disable the CC Status.rw TruthValue (SNMPv2-TC) .mplsATMPWMIB.1.1.11.1.1 |
dpwFlowTypeThis variable is used to set the flow type as E2E / SEG / Both.rw Enumeration .mplsATMPWMIB.1.1.11.1.2 |
dpwAtmoamRowStatusFor creating, modifying, and deleting this row. None of the
read-create objects in the conceptual rows may be changed
when this object is in the active(1) state.rw RowStatus (SNMPv2-TC) .mplsATMPWMIB.1.1.11.1.3 |
dpwFrequencyTimerIntvlThis variable is used to set the Frequency Timer Interval.
The frequency timer interval can be 1 or 2rw TruthValue (SNMPv2-TC) .mplsATMPWMIB.1.1.11.1.4 |
dpwAtmVpShapingTableThis table contains VP Shaping related parameters for upstream ont qos. SEQUENCE OF DpwAtmVpShapingEntry .mplsATMPWMIB.1.1.12 |
dpwAtmVpShapingEntryAn entry in this table is created for upstream ont qos vci-qos. DpwAtmVpShapingEntry .mplsATMPWMIB.1.1.12.1 |
dpwAtmVpShapingBandwidthThe Vp shaping bandwidth for upstream ATM cell packets.
The unit of bandwidth is in cell/seconds.rw Unsigned32 .mplsATMPWMIB.1.1.12.1.1 |
dpwAtmVpShapingRowStatusThis Object is used to create, modify and delete a row in this table.
When the Row status is active, whenever user configures in OLT, ONT is also configured.
For row creation, user is suggested to configure the bandwidth parameter after setting the
row status to create and wait. Then make the row status active.rw Unsigned32 .mplsATMPWMIB.1.1.12.1.2 |
dpwAtmOamStatsTableThe OAM statistic counts are in
this table.
This table provides OAM statistics information per ATM PW. SEQUENCE OF DpwAtmOamStatsEntry .mplsATMPWMIB.1.1.13 |
dpwAtmOamStatsEntryAn entry in this table is created when AIS/RDI cells are received.
Number of OAM cells Txmitted and received are incremented DpwAtmOamStatsEntry .mplsATMPWMIB.1.1.13.1 |
dpwAtmOamStatsOamCellsRxNumber of OAM Cells received.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.13.1.1 |
dpwAtmOamStatsOamCellsTxNumber of OAM Cells transmitted.ro PerfCurrentCount (PerfHist-TC-MIB) .mplsATMPWMIB.1.1.13.1.2 |