DLINKSW-POE-MIB
A MIB module for extending POWER-ETHERNET-MIB specified in RFC 3621.
Main OID:
dlinkSwPoeExtMIB.1.3.6.1.4.1.171.14.24
47
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
47 total| Object Name |
|---|
dlinkSwPoeExtMIBA MIB module for extending POWER-ETHERNET-MIB specified in
RFC 3621. MODULE-IDENTITY .1.3.6.1.4.1.171.14.24 |
dPoeMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.24.0 |
dPoeIfPowerDeniedNotificationThis Notification indicates if PSE state diagram enters
the state POWER_DENIED.
At least 500 msec must elapse between notifications
being emitted by the same object instance. NOTIFICATION-TYPE .1.3.6.1.4.1.171.14.24.0.1 |
dPoeIfPowerOverLoadNotificationThis Notification indicates if PSE state diagram enters
the state ERROR_DELAY_OVER.
At least 500 msec must elapse between notifications
being emitted by the same object instance. NOTIFICATION-TYPE .1.3.6.1.4.1.171.14.24.0.2 |
dPoeIfPowerShortCircuitNotificationThis Notification indicates if PSE state diagram enters
the state ERROR_DELAY_SHORT.
At least 500 msec must elapse between notifications
being emitted by the same object instance. NOTIFICATION-TYPE .1.3.6.1.4.1.171.14.24.0.3 |
dPoeIfPdAliveFailOccurNotificationThis Notification indicates if the PD device has
the stop working or no response problem. NOTIFICATION-TYPE .1.3.6.1.4.1.171.14.24.0.4 |
dPoeMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.24.1 |
dPoeGroupCfgTableThis table consists of a list of group configurations for PoE.
Group means box in the stack or module in a rack.
For non-modular devices, the pethMainPseGroupIndex is 1. SEQUENCE OF DPoeGroupCfgEntry .1.3.6.1.4.1.171.14.24.1.1 |
dPoeGroupCfgEntryAn entry contains the system configuration of the PoE on a group. DPoeGroupCfgEntry .1.3.6.1.4.1.171.14.24.1.1.1 |
dPoeGroupPolicyPreemptThis object configures whether to disconnect the PD which is powered
with lower priority in order to release the power to the new connected
PD with higher priority under power shortage condition.
If this object is 'false', then the policy is first in first serviced.
Thus the new PD will not be serviced if the power budget is running out.
If this object is 'true', then the power provisioned to PD
with lower priority can be preempted to release the power to the new
connected PD with higher priority.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.14.24.1.1.1.1 |
dPoeGroupClearIfStatisticThis object is used to clear the PoE statistics of pethPsePortEntry
for specified ports.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.171.14.24.1.1.1.2 |
dPoeGroupIfLedModeFor some devices,port LED can indicate either poe status or link status.
This object is used to configure or display port LED mode.
poeMode(1) - indicates poe status.
linkMode(2) - indicates link status.
For other devices have LEDs to indicate poe status and link status separately,
this object only can get value of invalid(3) to mean this node is meaningless.rw Enumeration .1.3.6.1.4.1.171.14.24.1.1.1.3 |
dPoeGroupInfoTableThis table consists of a list of PoE information for groups. SEQUENCE OF DPoEGroupInfoEntry .1.3.6.1.4.1.171.14.24.1.2 |
dPoeGroupInfoEntryAn entry contains the system information of the PoE on a group. DPoEGroupInfoEntry .1.3.6.1.4.1.171.14.24.1.2.1 |
dPoeGroupMaxPortsThis object indicates the maximum number of ports that the group can support.ro Integer32 .1.3.6.1.4.1.171.14.24.1.2.1.1 |
dPoeGroupHWVersionThis object indicates H/W version of PoE chip.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.14.24.1.2.1.2 |
dPoeGroupSWVersionThis object indicates firmware version of PoE chip.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.14.24.1.2.1.3 |
dPoeIfObjects OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.24.1.3 |
dPoeIfCfgTableThis table consists of a list of PoE configuration
information for ports. SEQUENCE OF DPoeIfCfgEntry .1.3.6.1.4.1.171.14.24.1.3.1 |
dPoeIfCfgEntryAn entry contains PoE configuration on a port. DPoeIfCfgEntry .1.3.6.1.4.1.171.14.24.1.3.1.1 |
dPoeIfStateThis object indicates the PoE state of the entry.
auto(1) - the port will automatically detect the PD and provision
power to the PD. The max wattage value which can be provisioned
to the port is determined by dPoeIfMaxPower. If dPoeIfMaxPower
is unspecified, then the class of the PD auto determines the
maximum wattage which can be provisioned. The PD will not be
provisioned if it requests more wattage than the max wattage
which is determined.
never(2) - indicates the port will not supply power to connected PD;
static(3) - indicates manager pre-allocate power budget to the port
by configuring the dPoeIfMaxPower object. The power budget is allocated
to the port even though there is no PD connected to the port.
If dPoeIfMaxPower is not configured, default value is 15400mW for 802.3af
and 30000mW for 802.3at.rw Enumeration .1.3.6.1.4.1.171.14.24.1.3.1.1.1 |
dPoeIfMaxPowerThis object indicates the max wattage value which can
be provisioned to the port.
Note: This object is valid only while the dPoeIfState
object is configured as auto or static.rw Integer32( 0 | 1000..30000) UNITS "milliwatts" .1.3.6.1.4.1.171.14.24.1.3.1.1.2 |
dPoeIfTimeRangeThis object indicates the name of time-range profile to delineate
the activation period.
A zero length string indicates the time-range is not specified.
Note: This object is valid only while the dPoeIfState is 'auto'.rw DisplayString .1.3.6.1.4.1.171.14.24.1.3.1.1.3 |
dPoeIfLegacyPdEnabledThis object indicates the state of legacy PD support.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.14.24.1.3.1.1.4 |
dPoeIfInfoObjects OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.24.1.3.2 |
dPoeIfStatusTableThis table consists of a list of PoE status for ports. SEQUENCE OF DPoeIfStatusEntry .1.3.6.1.4.1.171.14.24.1.3.2.1 |
dPoeIfStatusEntryAn entry consists of PoE status for a port. DPoeIfStatusEntry .1.3.6.1.4.1.171.14.24.1.3.2.1.1 |
dPoeIfDetectStatusThis object indicates the operational status of the port PD detection.
disabled(1) - PSE function is disabled.
searching(2) - Remote PD is not connected.
requesting(3) - Remote PD is inserted, but the PSE doesn't provide power yet.
delivering(4) - Remote PD is now powering by PoE system.
faulty(5) - Device detection or a powered device is in a faulty state.ro Enumeration .1.3.6.1.4.1.171.14.24.1.3.2.1.1.1 |
dPoeIfFaultyTypeThis object indicates the specific faulty type. It is meaningful
only when dPoeIfDetectStatus object is 'faulty'.
notApplicable(0) - indicates this object is meaningless, e.g. the
dPoeIfDetectStatus is not 'faulty'.
mpsAbsent(1) - indicates MPS(Maintain Power Signature) Absent
pdShort(2) - indicates PD Short
overload(3) - indicates Overload
powerDenied(4) - indicates Power Denied
thermalShutdown(5)- indicates Thermal Shutdown
startupFailure(6) - indicates Startup Failure
classificationFailure(7) - indicates Classification Failure(IEEE 802.3at)ro Enumeration .1.3.6.1.4.1.171.14.24.1.3.2.1.1.2 |
dPoeIfMeasurementTableThis table consists of a list of POE measurement
information for ports. SEQUENCE OF DPoEIfMeasurementEntry .1.3.6.1.4.1.171.14.24.1.3.2.2 |
dPoeIfMeasurementEntryAn entry consists of PoE measurement information of a port. DPoEIfMeasurementEntry .1.3.6.1.4.1.171.14.24.1.3.2.2.1 |
dPoeIfVoltageThis object indicates the voltage of the port in millivolts.ro Integer32 UNITS "millivolts" .1.3.6.1.4.1.171.14.24.1.3.2.2.1.1 |
dPoeIfCurrentThis object indicates the current of port in milliamperes.ro Integer32 UNITS "milliamperes" .1.3.6.1.4.1.171.14.24.1.3.2.2.1.2 |
dPoeIfTemperatureThis object indicates the temperature of port in degrees centigrade.ro Integer32 UNITS "Degree Centigrade" .1.3.6.1.4.1.171.14.24.1.3.2.2.1.3 |
dPoeIfPowerThis object indicates consumption power of port in milliwatts.ro Integer32 .1.3.6.1.4.1.171.14.24.1.3.2.2.1.4 |
dPoeIfPdAliveCfgTableThis table consists of a list of configuration for the PD
alive check function for ports.
The PD alive check feature provides the solution for
PD device that has the stop working or no response
problem via Ping mechanism.
Detailed Process:
The detailed processes are described as follows:
1. The system needs to periodically monitor the
specific PD by using Ping function. If there is no
response, system takes one of the following actions:
(1) Reset: Switch resets (disable then enable) PoE
power on the port which connects to a PD under monitoring.
(2) Notify: Switch sends logs and traps to notify the administrator.
(3) Both: Switch sends logs and traps, and resets the PoE port power.
2. The system should implement the retry mechanism to check
PD aliveness, hence the system will reset the PoE port power
feeding after the retry by using Ping without any response from a PD.
3. If the action is Reset or Both, the system needs
to wait for PD recovery from rebooting and then executes
the Ping function again. Besides, the waiting time can
be configured by users.
4. If PoE schedule (time range) function is configured
on the port which enables the PD Alive Check function,
the time range function has the top priority, and
therefore PD Alive Check function will not work
while PoE time range function is still active.
5. This function only takes effect on PoE enabled
port with power feeding.
Note: It is required to setup IP settings properly that
the PD can be reachable for Ping, otherwise this function
cannot work as expected.
Limitation
1. Support Ping Function: If the PD does not support ICMP,
this function cannot work normally.
2. Direct-Connected PD: The Reset Action can only work on
the direct-connected PD. If the PD is not connected directly,
the Reset Action may not work as expected.
3. PD Also Acts as PSE: If the direct-connected PD is also a PSE,
all the next level PDs connect to this PSE will be power cycling
whenever PD Alive Check function takes effect on 'Reset' or 'Both' Action. SEQUENCE OF DPoeIfPdAliveCfgEntry .1.3.6.1.4.1.171.14.24.1.3.3 |
dPoeIfPdAliveCfgEntryAn entry contains configuration for PD alive check on a port. DPoeIfPdAliveCfgEntry .1.3.6.1.4.1.171.14.24.1.3.3.1 |
dPoeIfPdAliveCfgStateThis object indicates the the PD alive function sate.
enabled - Enable the PD alive check function
disabled - Disable the PD alive check function.rw Enumeration .1.3.6.1.4.1.171.14.24.1.3.3.1.1 |
dPoeIfPdAliveCfgPdIpTypeThis object indicates the IP address type of the target PD.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.14.24.1.3.3.1.2 |
dPoeIfPdAliveCfgPdIpAddrThis object indicates the IP address of the target PD.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.14.24.1.3.3.1.3 |
dPoeIfPdAliveCfgIntervalThis object indicates the time interval for system
issues ping request to detect the target PD.
The valid range for interval time is 10s to 300s.rw Unsigned32 .1.3.6.1.4.1.171.14.24.1.3.3.1.4 |
dPoeIfPdAliveCfgRetryThis object indicates the retry count of ping
request when PD has no response.
The valid range for retry count is 0 to 5 times.rw Unsigned32 .1.3.6.1.4.1.171.14.24.1.3.3.1.5 |
dPoeIfPdAliveCfgWaitTimeThis object indicates the waiting time for PD reboot.
The valid range for waiting time is 30s to 300s.rw Unsigned32 .1.3.6.1.4.1.171.14.24.1.3.3.1.6 |
dPoeIfPdAliveCfgActionThis object indicates the action when PD doesn't reply the ping request.
reset- System will reset the PoE port state .
notify- System will send log and trap to notify the administrator.
both- System will send log and trap first and reset the PoE port state.rw Enumeration .1.3.6.1.4.1.171.14.24.1.3.3.1.7 |
dPoeMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.24.2 |
dPoeMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.24.2.1 |
dPoeMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.24.2.2 |