DGS-1210-28ME_AX
AI MIB Summary
Standard SNMP MIB module defining data structures for DGS-1210-28ME_AX.
1928
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
1928 total| Object Name |
|---|
d-link OBJECT IDENTIFIER .1.3.6.1.4.1.171 |
dlink-products OBJECT IDENTIFIER .1.3.6.1.4.1.171.10 |
dlink-DGS12XXSeriesProd OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76 |
dgs-1210-28me OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28 |
dgs-1210-28meax OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1 |
companySystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.1 |
sysSwitchNameSystem name used for identification of the device.
The following characters are allowed to input.
0 ~ 9 / a ~ z / A ~ Z
Special character: ( ) V + _ = .rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.1 |
sysHardwareVersionVersion number of the Hardware.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.2 |
sysFirmwareVersionVersion number of the Firmware.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.3 |
sysLoginTimeoutIntervalThis time interval is used to count the time and
logout web interface automatically.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.1.4 |
sysLocationNameThe location name of this node (e.g., `telephone closet,
3rd floor'). If the location is unknown, the value is
the zero-length string.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.5 |
sysGroupIntervalGroup Interval is used to send D-link Discover packet to D-link
SmartConsole Utility frequency.
The timer in units of seconds.
Set value 0 to disable group Interval.rw Integer32 (0 | 120..1225) .1.3.6.1.4.1.171.10.76.28.1.1.6 |
sysSafeGuardEnableThis object is used to set Safeguard Enable\Disable.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.8 |
sysRestartThis object allows the user to restart the Switch
(i.e)the entire switch will operationally go down and
start again. Setting a value of 'true' causes the switch
to be restarted.
When the switch operationally goes down, configuration
save operation is initiated based on the configuration save
option chosen.
When the switch operationally come up, the saved configurations
are restored based on the restore option chosen.
Once the switch is restarted, the value of this object reverts
to 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.1.9 |
sysSaveThis object is used to save Configuration , value 1 is save in process ,
value 2 is not in process , value 3 is save config_1 and value 4 is save config_2.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.10 |
sysJumboFrameEnableGigabit Web Smart Switches support jumbo frames (frames larger than
the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged).
Default jumbo frame is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.12 |
sysPortCtrlTableA table to control the port specific parameters of the device like speed,
duplex mode, etc. SEQUENCE OF SysPortCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.1.13 |
sysPortCtrlEntryAn entry appears in this table for each interface in the system.
Index to the table is the interface index of the port. SysPortCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.1.13.1 |
sysPortCtrlIndexInterface index of the port for the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.1.13.1.1 |
sysPortCtrlMediumTypeThis object indicates the port type: fiber 1G/100M or copper.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.13.1.2 |
sysPortCtrlSpeedConfigures interface speed.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.13.1.3 |
sysPortCtrlOperStatusThe port's operating speed state.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.13.1.4 |
sysPortCtrlMDIConfigures interface auto/mdi/mdix mode.
The default setting is Auto.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.13.1.5 |
sysPortCtrlFlowControlEnables / disables flow control for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.13.1.6 |
sysPortCtrlFlowControlOperThe link parner negotiate port's operating flow control state.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.13.1.7 |
sysPortCtrlTypeThe port's media type.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.13.1.8 |
sysPortCtrlCapabilityThe port's capability advertised.rw Bits .1.3.6.1.4.1.171.10.76.28.1.1.13.1.9 |
sysPortDescriptionTableThe port description table. SEQUENCE OF SysPortDescriptionEntry .1.3.6.1.4.1.171.10.76.28.1.1.14 |
sysPortDescriptionEntryThe port description entry. SysPortDescriptionEntry .1.3.6.1.4.1.171.10.76.28.1.1.14.1 |
sysPortDescIndexThis object indicates the port index.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.14.1.1 |
sysPortDescMediumTypeThis object indicates the port type: fiber 1G/100M or copper.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.14.1.2 |
sysPortDescStringThis object indicates the port description.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.14.1.3 |
sysPortUpLinkTimeThis object indicates the port link up time.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.14.1.4 |
sysPortErrTableThe port error table. SEQUENCE OF SysPortErrEntry .1.3.6.1.4.1.171.10.76.28.1.1.15 |
sysPortErrEntryA list of information for the err port of the device. SysPortErrEntry .1.3.6.1.4.1.171.10.76.28.1.1.15.1 |
sysPortErrPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.15.1.1 |
sysPortErrPortStateThis object decides whether the port state is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.15.1.2 |
sysPortErrPortStatusThis object decides whether the PortStatus is err-disabled.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.15.1.3 |
sysPortErrPortReasonThis object decides whether the PortStatus is LBD.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.15.1.4 |
sysDhcpAutoConfigurationThis object indicates auto config is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.16 |
sysWebStateThis object is for Enabled(1) or Disabled(2) Web state in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.17 |
sysWebPortNumberWeb Server Port Number.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.1.18 |
sysARPAgingTimeThis object is for ARP aging time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.19 |
sysMACAgingTimeThis object is for MAC aging time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.20 |
baudRateConfigurationTo set SerialPort baud-rate configuration.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.21 |
autologoutConfigurationTo set SerialPort auto-logout-time configuration.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.22 |
telnetsettingManagementOnOffEnable/Disable management Telnetsetting mechanism.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.23 |
telnetUDPPortThe value is for setting telnet's UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.24 |
autoRefreshConfigurationTo set the WEB panel auto refresh timer.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.25 |
floodfdbOnOffTo set enable status for flood fdb.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.26 |
sysContactNameTo set system contact name.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.27 |
sysDhcpAutoConfigTimeoutTo set dhcp auto config timeout.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.28 |
sysCommandLoggingTo set enable status for CommandLogging.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.29 |
sysSerialNumberTo get the serial number.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.30 |
sysFirmwareInfomation OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.1.31 |
sysVersionThe version of firmware information.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.31.1 |
sysSizeThe size of firmware information.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.1.31.2 |
sysUpdateTimeThe Update Time of firmware information.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.31.3 |
sysFromIPThe IP address of firmware information.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.1.31.4 |
sysUserThe user of firmware infomation.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.31.5 |
sysTypeThe type of firmware infomation.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.31.6 |
sysDdp OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.1.32 |
sysDdpGlobalOnOffThis object indicates D-Link discover protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.32.1 |
sysDdpGeneralReportOnOffThis object indicates D-Link discover protocol report is enabled or disabled.
This object only can be modified when D-Link discover protocol state is enabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.32.2 |
sysDdpGeneralReportTimerThis object indicates D-Link discover protocol report time period.
This object only can be modified when both D-Link discover protocol state and
D-Link discover protocol report state are enabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.32.3 |
sysDdpProtStatusTableA table to control the port status of D-Link discover protocol. SEQUENCE OF SysDdpProtStatusEntry .1.3.6.1.4.1.171.10.76.28.1.1.32.4 |
sysDdpProtStatusEntryAn entry appears in this table for each port D-Link discover protocol status. SysDdpProtStatusEntry .1.3.6.1.4.1.171.10.76.28.1.1.32.4.1 |
sysDdpProtStatusIndexInterface index of the port for the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.1.32.4.1.1 |
sysDdpProtStatusControlConfigures the port status of D-Link discover protocol.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.32.4.1.2 |
sysDhcpAutoImageThis object indicates auto image is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.34 |
sysBootupConfigIDTo get/set bootup config ID.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.35 |
sysBootupImageTo get/set bootup Image.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.1.36 |
sysPortMediaTypeTableA table to control the port specific parameters of the device like speed,
Vendor name, etc. SEQUENCE OF SysPortMediaTypeEntry .1.3.6.1.4.1.171.10.76.28.1.1.37 |
sysPortMediaTypeEntryAn entry appears in this table for each interface in the system.
Index to the table is the interface index of the port. SysPortMediaTypeEntry .1.3.6.1.4.1.171.10.76.28.1.1.37.1 |
sysPortMediaTypeIndexInterface index of the port for the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.1.37.1.1 |
sysPortMediaTypeThis object indicates the port type: fiber 1G/100M or copper.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.37.1.2 |
sysPortTypeConfigures interface speed.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.1.37.1.3 |
sysPortMediaTypeVendorNameThe port's VendorName.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.37.1.4 |
sysPortMediaTypeOuiThe port's Oui.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.37.1.5 |
sysPortMediaTypePnThe port's Pn.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.37.1.6 |
sysPortMediaTypeRevThe port's Rev.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.37.1.7 |
sysPortMediaTypeSnThe port's Sn.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.37.1.8 |
sysPortMediaTypeDateCodeThe port's DateCode.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.1.37.1.9 |
companyIpifGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.2 |
ipv4sysIpAddrCfgModeSpecifies the means by which the default interface in the device
gets the IP address.
If 'manual' mode is selected, the default interface takes the
'sysDefaultIpAddr' configured in the system.
If 'dynamic' mode is selected, the default interface gets the IP address
through dynamic IP address configuration protocols such as RARP client,
BootP client, DHCP Client, etc.
If the system fails to get the IP address dynamically through all the
above protocols, the default interface uses the 'sysDefaultIpAddr'
configured in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.1 |
ipv4sysIpAddrDefault IP Address of the system.
This IP address, if modified, will take effect only when the
configuration is stored & restored.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.2.2 |
ipv4sysIpSubnetMaskIP subnet mask for the default IP address.
This subnet mask, if modified, will take effect only when the
configuration is stored & restored.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.2.3 |
ipv4sysGatewayGatewayrw IpAddress .1.3.6.1.4.1.171.10.76.28.1.2.4 |
ipv4dhcpOption12StatusStatus of DHCP Option12rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.5 |
ipv4dhcpOption12HostNameHost name in DHCP option 12rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.2.6 |
ipifSupportV4V6Info OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.2.7 |
sysIpAddrCfgModeSpecifies the means by which the default interface in the device
gets the IP address.
If 'manual' mode is selected, the default interface takes the
'sysDefaultIpAddr' configured in the system.
If 'dynamic' mode is selected, the default interface gets the IP address
through dynamic IP address configuration protocols such as RARP client,
BootP client, DHCP Client, etc.
If the system fails to get the IP address dynamically through all the
above protocols, the default interface uses the 'sysDefaultIpAddr'
configured in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.7.1 |
sysIpAddrDefault IP Address of the system.
This IP address, if modified, will take effect only when the
configuration is stored & restored.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.2.7.2 |
sysIpSubnetMaskIP subnet mask for the default IP address.
This subnet mask, if modified, will take effect only when the
configuration is stored & restored.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.2.7.3 |
sysGatewayGatewayrw IpAddress .1.3.6.1.4.1.171.10.76.28.1.2.7.4 |
dhcpOption12StatusStatus of DHCP Option12rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.7.5 |
dhcpOption12HostNameHost name in DHCP option 12rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.2.7.6 |
ipifNameThe Description for the interface.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.2.7.7 |
ipifVLANnameThe vlan name for the interface.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.2.7.8 |
ipifv6GlobalStatusThe ID of VLAN that you want this interface to be in.
It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.7.9 |
ipifv6DHCPStatusThe state of DHCPv6 that you want this interface to be in.
It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.7.10 |
ipifv6AutolinkloStatusThe global state of link local that you want this interface to be in.
It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.7.11 |
ipifv6NSRetransmitTimeThe NS's retransmit time that you want this interface to be in.
It must be a exist vlan id (1~3600).rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.2.7.12 |
ipifv6DefaultGatewayThe ipv6 default gateway that you want this interface to be in.
It must be a exist vlan id.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.2.7.13 |
ipifV6AddressTableA list of interface entries. SEQUENCE OF IpifV6AddressEntry .1.3.6.1.4.1.171.10.76.28.1.2.7.14 |
ipifV6AddressEntryAn entry containing management information applicable
to a particular interface. IpifV6AddressEntry .1.3.6.1.4.1.171.10.76.28.1.2.7.14.1 |
ipifV6AddressMainIndexThe index of this IPv6 entry.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.2.7.14.1.1 |
ipifV6AddressIpAddrThe ip address of this IPv6 entry.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.2.7.14.1.2 |
ipifV6AddressIpPrefixThe ip prefix of this IPv6 entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.2.7.14.1.3 |
ipifV6AddressIpTypeThe ip type of this IPv6 entry.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.2.7.14.1.4 |
ipifV6AddressRowStatusThe status of an entry in the Multi Interface Table. Only a subset
of the rowstatus variables (active, createAndWait, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.2.7.14.1.5 |
ipv4sysIprouteGatewayIProute Gateway of the system.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.2.8 |
ipv4sysIprouteHopsIProute Hops of the system.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.2.9 |
companyTftpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.3 |
tftpFwServerIpAddressThe TFTP server's IP address is used to upload or
download firmware.rwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.3.1 |
tftpFwImageFileNameConfigure firmware filename to download.rwobsolete DisplayString .1.3.6.1.4.1.171.10.76.28.1.3.2 |
tftpFwTftpOperationThe tftp operates to perform downloading the firmware image
to the unit. This object is used in conjunction with
configBootTftpServerIp and configBootImageFileName.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.3 |
tftpFwTftpOperationStatusThe tftp operation status represent firmware backup or upgrade status.roobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.4 |
tftpCfgServerIpAddressThe TFTP server's IP address is used to upload or
download configuration file.rwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.3.5 |
tftpConfigFileNameThe configuration filename is used to store or retrieve config
from the tftp server.rwobsolete DisplayString .1.3.6.1.4.1.171.10.76.28.1.3.6 |
tftpConfigTftpOperationThe tftp operates to perform either downloading the
configuration file to the unit or uploading the current
configuration file to the tftp server. This object is
used in conjunction with configTftpServerIpAddress
and configTftpServerFileName.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.7 |
tftpConfigTftpOperationStatusThe tftp operation status represent configuration file backup or restore status.roobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.8 |
tftpFwTargetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.3.9 |
tftpFwTargetServerIpAddressThe TFTP server's IP address is used to upload or
download firmware.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.3.9.1 |
tftpFwTargetServerIpTypeType of IP interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.9.2 |
tftpFwTargetInterfaceNameSpecifies the interface name when the tftpFwTargetServerIpAddress
is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.3.9.3 |
tftpFwTargetImageFileNameConfigure firmware filename to download.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.3.9.4 |
tftpFwTargetTftpOperationThe tftp operates to perform downloading the firmware image
to the unit. This object is used in conjunction with
configBootTftpServerIp and configBootImageFileName.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.9.5 |
tftpFwTargetTftpOperationStatusThe tftp operation status represent firmware backup or upgrade status.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.9.6 |
tftpCfgTargetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.3.10 |
tftpCfgTargetServerIpAddressThe TFTP server's IP address is used to upload or
download configuration file.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.3.10.1 |
tftpCfgTargetServerIpTypeType of IP interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.10.2 |
tftpCfgTargetInterfaceNameSpecifies the interface name when the tftpCfgTargetServerIpAddress
is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.3.10.3 |
tftpCfgTargetImageFileNameThe configuration filename is used to store or retrieve config
from the tftp server.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.3.10.4 |
tftpCfgTargetTftpOperationThe tftp operates to perform either downloading the
configuration file to the unit or uploading the current
configuration file to the tftp server. This object is
used in conjunction with configTftpServerIpAddress
and configTftpServerFileName.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.10.5 |
tftpCfgTargetTftpOperationStatusThe tftp operation status represent configuration file backup or restore status.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.10.6 |
tftpCfgTargetConfigIDThe tftp operates to perform either downloading the
configuration file to the unit or uploading the current
configuration file to the tftp server. This object is
used in conjunction with configTftpServerIpAddress
and configTftpServerFileName.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.3.10.7 |
companyMiscGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.4 |
miscResetPhysically resets the unit - use with care. A (1) resets
the unit, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.4.2 |
miscStatisticsResetResets the units statistics. A (1) resets
the statistics count, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.4.3 |
companySNMPV3 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5 |
snmpGlobalStateThis object is for enabling or disabling SNMP Community function.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.1 |
snmpV3User OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5.2 |
snmpV3UserTable SEQUENCE OF SnmpV3UserEntry .1.3.6.1.4.1.171.10.76.28.1.5.2.1 |
snmpV3UserEntry SnmpV3UserEntry .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1 |
snmpV3UserNameA human readable string representing the name of
the user.
This is the (User-based Security) Model dependent
security ID.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.1 |
snmpV3UserVersionA human readable string representing the name of
the user.
This is the (User-based Security) Model dependent
security ID.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.2 |
snmpV3UserGroupNameThe name of the group to which this entry (e.g., the
combination of securityModel and securityName)
belongs.
This groupName is used as index into the
vacmAccessTable to select an access control policy.
However, a value in this table does not imply that an
instance with the value exists in table vacmAccesTable.rw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.3 |
snmpV3UserAuthProtocolAn indication of whether messages sent on behalf of
this user to/from the SNMP engine identified by
usmUserEngineID, can be authenticated, and if so,
the type of authentication protocol which is used.
An instance of this object is created concurrently
with the creation of any other object instance for
the same user (i.e., as part of the processing of
the set operation which creates the first object
instance in the same conceptual row).
If an initial set operation (i.e. at row creation time)
tries to set a value for an unknown or unsupported
protocol, then a 'wrongValue' error must be returned.
The value will be overwritten/set when a set operation
is performed on the corresponding instance of
UserCloneFrom.
Once instantiated, the value of such an instance of
this object can only be changed via a set operation to
the value of the NoAuthProtocol.
If a set operation tries to change the value of an
existing instance of this object to any value other
than NoAuthProtocol, then an 'inconsistentValue'
error must be returned.
If a set operation tries to set the value to the
NoAuthProtocol while the UserPrivProtocol value
in the same row is not equal to NoPrivProtocol,
then an 'inconsistentValue' error must be returned.
That means that an SNMP command generator application
must first ensure that the UserPrivProtocol is set
to the NoPrivProtocol value before it can set
the UserAuthProtocol value to NoAuthProtocol.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.4 |
snmpV3UserAuthProtocolPasswordrw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.5 |
snmpV3UserPrivProtocolAn indication of whether messages sent on behalf of
this user to/from the SNMP engine identified by
usmUserEngineID, can be protected from disclosure,
and if so, the type of privacy protocol which is used.
An instance of this object is created concurrently
with the creation of any other object instance for
the same user (i.e., as part of the processing of
the set operation which creates the first object
instance in the same conceptual row).
If an initial set operation (i.e. at row creation time)
tries to set a value for an unknown or unsupported
protocol, then a 'wrongValue' error must be returned.
The value will be overwritten/set when a set operation
is performed on the corresponding instance of
usmUserCloneFrom.
Once instantiated, the value of such an instance of
this object can only be changed via a set operation to
the value of the NoPrivProtocol.
If a set operation tries to change the value of an
existing instance of this object to any value other
than NoPrivProtocol, then an 'inconsistentValue'
error must be returned.
Note that if any privacy protocol is used, then you
must also use an authentication protocol. In other
words, if usmUserPrivProtocol is set to anything else
than NoPrivProtocol, then the corresponding instance
of usmUserAuthProtocol cannot have a value of
usmNoAuthProtocol. If it does, then an
'inconsistentValue' error must be returned.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.6 |
snmpV3UserPrivProtocolPasswordrw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.7 |
snmpV3UserStatusThe status of this conceptual row.
Until instances of all corresponding columns are
appropriately configured, the value of the
corresponding instance of the usmUserStatus column
is 'notReady'.
In particular, a newly created row for a user who
employs authentication, cannot be made active until the
corresponding usmUserCloneFrom and usmUserAuthKeyChange
have been set.
Further, a newly created row for a user who also
employs privacy, cannot be made active until the
usmUserPrivKeyChange has been set.
The RowStatus TC [RFC2579] requires that this
DESCRIPTION clause states under which circumstances
other objects in this row can be modified:
The value of this object has no effect on whether
other objects in this conceptual row can be modified,
except for usmUserOwnAuthKeyChange and
usmUserOwnPrivKeyChange. For these 2 objects, the
value of usmUserStatus MUST be active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.5.2.1.1.8 |
snmpV3Group OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5.3 |
snmpV3GroupTable SEQUENCE OF SnmpV3GroupEntry .1.3.6.1.4.1.171.10.76.28.1.5.3.1 |
snmpV3GroupEntry SnmpV3GroupEntry .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1 |
snmpV3GroupNameThe name of the group to which this entry (e.g., the
combination of securityModel and securityName)
belongs.
This groupName is used as index into the
vacmAccessTable to select an access control policy.
However, a value in this table does not imply that an
instance with the value exists in table vacmAccesTable.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1.1 |
snmpV3GroupSecurityModelIn order to gain the access rights allowed by this
conceptual row, this securityModel must be in use.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1.2 |
snmpV3GroupSecurityLevelThe minimum level of security required in order to
gain the access rights allowed by this conceptual
row. A securityLevel of noAuthNoPriv is less than
authNoPriv which in turn is less than authPriv.
If multiple entries are equally indexed except for
this vacmAccessSecurityLevel index, then the entry
which has the highest value for
vacmAccessSecurityLevel is selected.ro SnmpSecurityLevel (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1.3 |
snmpV3GroupReadViewNameThe value of an instance of this object identifies
the MIB view of the SNMP context to which this
conceptual row authorizes read access.
The identified MIB view is that one for which the
vacmViewTreeFamilyViewName has the same value as the
instance of this object; if the value is the empty
string or if there is no active MIB view having this
value of vacmViewTreeFamilyViewName, then no access
is granted.rw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1.4 |
snmpV3GroupWriteViewNameThe value of an instance of this object identifies
the MIB view of the SNMP context to which this
conceptual row authorizes write access.
The identified MIB view is that one for which the
vacmViewTreeFamilyViewName has the same value as the
instance of this object; if the value is the empty
string or if there is no active MIB view having this
value of vacmViewTreeFamilyViewName, then no access
is granted.rw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1.5 |
snmpV3GroupNotifyViewNameThe value of an instance of this object identifies
the MIB view of the SNMP context to which this
conceptual row authorizes access for notifications.
The identified MIB view is that one for which the
vacmViewTreeFamilyViewName has the same value as the
instance of this object; if the value is the empty
string or if there is no active MIB view having this
value of vacmViewTreeFamilyViewName, then no access
is granted.rw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1.6 |
snmpV3GroupStatusThe status of this conceptual row.
The RowStatus TC [RFC2579] requires that this
DESCRIPTION clause states under which circumstances
other objects in this row can be modified:
The value of this object has no effect on whether
other objects in this conceptual row can be modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.5.3.1.1.7 |
snmpV3ViewTree OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5.4 |
snmpV3ViewTreeTable SEQUENCE OF SnmpV3ViewTreeEntry .1.3.6.1.4.1.171.10.76.28.1.5.4.1 |
snmpV3ViewTreeEntry SnmpV3ViewTreeEntry .1.3.6.1.4.1.171.10.76.28.1.5.4.1.1 |
snmpV3viewTreeNameThe human readable name for a family of view subtrees.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.4.1.1.1 |
snmpV3viewTreeSubtreeThe MIB subtree which when combined with the
corresponding instance of vacmViewTreeFamilyMask
defines a family of view subtrees.ro OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5.4.1.1.2 |
snmpV3viewTreeMaskThe bit mask which, in combination with the
corresponding instance of vacmViewTreeFamilySubtree,
defines a family of view subtrees.
Each bit of this bit mask corresponds to a
sub-identifier of vacmViewTreeFamilySubtree, with the
most significant bit of the i-th octet of this octet
string value (extended if necessary, see below)
corresponding to the (8*i - 7)-th sub-identifier, and
the least significant bit of the i-th octet of this
octet string corresponding to the (8*i)-th
sub-identifier, where i is in the range 1 through 16.
Each bit of this bit mask specifies whether or not
the corresponding sub-identifiers must match when
determining if an OBJECT IDENTIFIER is in this
family of view subtrees; a '1' indicates that an
exact match must occur; a '0' indicates 'wild card',
i.e., any sub-identifier value matches.
Thus, the OBJECT IDENTIFIER X of an object instance
is contained in a family of view subtrees if, for
each sub-identifier of the value of
vacmViewTreeFamilySubtree, either:
the i-th bit of vacmViewTreeFamilyMask is 0, or
the i-th sub-identifier of X is equal to the i-th
sub-identifier of the value of
vacmViewTreeFamilySubtree.
If the value of this bit mask is M bits long and
there are more than M sub-identifiers in the
corresponding instance of vacmViewTreeFamilySubtree,
then the bit mask is extended with 1's to be the
required length.
Note that when the value of this object is the
zero-length string, this extension rule results in
a mask of all-1's being used (i.e., no 'wild card'),
and the family of view subtrees is the one view
subtree uniquely identified by the corresponding
instance of vacmViewTreeFamilySubtree.
Note that masks of length greater than zero length
do not need to be supported. In this case this
object is made read-only.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.5.4.1.1.3 |
snmpV3viewTreeTypeIndicates whether the corresponding instances of
vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask
define a family of view subtrees which is included in
or excluded from the MIB view.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.4.1.1.4 |
snmpV3viewTreeStatusThe status of this conceptual row.
The RowStatus TC [RFC2579] requires that this
DESCRIPTION clause states under which circumstances
other objects in this row can be modified:
The value of this object has no effect on whether
other objects in this conceptual row can be modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.5.4.1.1.5 |
snmpV3Community OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5.5 |
snmpV3CommunityTable SEQUENCE OF SnmpV3CommunityEntry .1.3.6.1.4.1.171.10.76.28.1.5.5.1 |
snmpV3CommunityEntry SnmpV3CommunityEntry .1.3.6.1.4.1.171.10.76.28.1.5.5.1.1 |
snmpV3CommunityNameThe unique index value of a row in this table.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.5.5.1.1.1 |
snmpV3CommunityPolicyA human readable string representing the corresponding
value of snmpCommunityName in a Security Model
independent format.rw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.5.1.1.2 |
snmpV3CommunityStatusThe status of this conceptual row in the
snmpCommunityTable.
An entry in this table is not qualified for activation
until instances of all corresponding columns have been
initialized, either through default values, or through
Set operations. The snmpCommunityName and
snmpCommunitySecurityName objects must be explicitly set.
There is no restriction on setting columns in this table
when the value of snmpCommunityStatus is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.5.5.1.1.3 |
snmpV3Host OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5.6 |
ipv4snmpV3HostTableobsolete SEQUENCE OF Ipv4snmpV3HostEntry .1.3.6.1.4.1.171.10.76.28.1.5.6.1 |
ipv4snmpV3HostEntryobsolete Ipv4snmpV3HostEntry .1.3.6.1.4.1.171.10.76.28.1.5.6.1.1 |
ipv4snmpV3HostAddressThis object contains a transport address. The format of
this address depends on the value of the
snmpTargetAddrTDomain object. And this object is unique
identifier associated with this snmpNotifyEntry.roobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.5.6.1.1.1 |
ipv4snmpV3HostCommunityNameThe locally arbitrary.rwobsolete SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.6.1.1.2 |
ipv4snmpV3HostVersionThe Level of Security to be used when generating
SNMP messages using this entry.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.6.1.1.3 |
ipv4snmpV3HostStatusrwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.5.6.1.1.4 |
snmpV3HostTable SEQUENCE OF SnmpV3HostEntry .1.3.6.1.4.1.171.10.76.28.1.5.6.2 |
snmpV3HostEntry SnmpV3HostEntry .1.3.6.1.4.1.171.10.76.28.1.5.6.2.1 |
snmpV3HostAddressThis object contains a transport address. The format of
this address depends on the value of the
snmpTargetAddrTDomain object. And this object is unique
identifier associated with this snmpNotifyEntry.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.5.6.2.1.1 |
snmpV3IPTypeType of IP interface.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.6.2.1.2 |
snmpV3HostCommunityNameThe locally arbitrary.rw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.5.6.2.1.3 |
snmpV3HostVersionThe Level of Security to be used when generating
SNMP messages using this entry.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.6.2.1.4 |
snmpV3HostInterfaceNameSpecifies the interface name when the syslogSrvIP is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.5.6.2.1.5 |
snmpV3HostStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.5.6.2.1.6 |
snmpV3EngineIDAn SNMP engine's administratively-unique identifier.
In a simple agent, this value is always that agent's
own snmpEngineID value.
The value can also take the value of the snmpEngineID
of a remote SNMP engine with which this user can
communicate.rw SnmpEngineID (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.171.10.76.28.1.5.7 |
snmpV3Trap OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.5.8 |
snmpV3TrapSNMPAuthenticationThis object is for enabling or disabling SNMP login fail
event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.1 |
snmpV3TrapColdStartThis object is for enabling or disabling devie Bootup event
trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.2 |
snmpV3TrapWarmStartThis object is for enabling or disabling devie Bootup event
trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.3 |
snmpV3TrapLinkUpDownThis object is for enabling or disabling Copper link up / link down
event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.4 |
snmpV3TrapRSTPStateChangeThis object is for enabling or disabling RSTP topology change
event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.5 |
snmpV3TrapFirmUpgradeThis object is for enabling or disabling Firmware upgrade
suess or fail event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.6 |
snmpV3TrapBPDUAttackUsed to configure trap settings for BPDU attack protection events.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.11 |
snmpV3TrapPortSecurityrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.12 |
snmpV3TrapIMPBViolationrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.13 |
snmpV3TrapLBDrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.14 |
snmpV3TrapDHCPServerScreeningrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.15 |
snmpV3TrapDuplicateIPDetectedThis object is for enabling or disabling send gratuitous
trap when IP address conflicted in the network.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.8.16 |
snmpV3CommunityEncryptionThis object is for enabling or disabling community encryption.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.5.9 |
companySTP OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.6 |
stpBridgeGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.6.1 |
stpModuleStatusThe administrative status requested by management for the MST
feature. The value enabled(1) indicates that Mst should be enabled
in the device on all ports. The value disabled(2) indicates that
Mst should be disabled in the device on all ports. The object can
be set to enabled(1) if and only if, fsMIMstSystemControl set to start.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.1.1 |
stpProtocolVersionThe version of Spanning Tree Protocol the bridge is
currently running. The value 'stpCompatible(0)'
indicates the Spanning Tree Protocol specified in
IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning
Tree Protocol specified in IEEE 802.1w and 'mstp(3)'
indicates the Multiple Spanning Tree Protocol Specified
in IEEE 802.1s.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.1.2 |
stpBridgePriorityThe Value of the writable portion of the Bridge
Identifier comprising of the first two octets.
The values that are set for Bridge Priority must be
in steps of 4096.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.1.3 |
stpTxHoldCountThe value used by the Port Transmit state machine to limit
the maximum transmission rate.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.1.4 |
stpBridgeMaxAgeThe value that all bridges use for MaxAge when
this bridge is acting as the root. The granularity
of this timer is specified to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.171.10.76.28.1.6.1.5 |
stpBridgeHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node in units
of hundredths of a second.rw Timeout .1.3.6.1.4.1.171.10.76.28.1.6.1.6 |
stpBridgeForwardDelayThe value that all bridges use for ForwardDelay
when this bridge is acting as the root. Note that
802.1D specifies that the range for this
parameter is related to the value of
BridgeMaxAge. The granularity of this
timer is specified to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.171.10.76.28.1.6.1.7 |
stpFowardBPDUThis object is for enabling or disabling forward BPDU.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.1.8 |
stpRootBridgeThe bridge identifier of the Root of the common spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the CIST Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro BridgeId .1.3.6.1.4.1.171.10.76.28.1.6.1.9 |
stpRootCostThe Cost of the path to the CIST Root as seen
from this bridge.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.1.10 |
stpMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Timeout .1.3.6.1.4.1.171.10.76.28.1.6.1.11 |
stpForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in a particular state before moving to the
next state.ro Timeout .1.3.6.1.4.1.171.10.76.28.1.6.1.12 |
stpRootPortThe Port Number of the Port which offers the lowest
path cost from this bridge to the CIST Root Bridge.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.1.13 |
stpTopologyChangeTrapStatusThis object is for enabling or disabling topology change event
trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.1.14 |
stpNewRootTrapStatusThis object is for enabling or disabling new root event
trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.1.15 |
stpNewRootTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.6.1.16 |
brgAddressThe MAC address used by this bridge when it must
be referred to in a unique fashion. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.76.28.1.6.1.16.1 |
oldDesignatedRootThe bridge identifier of the old root of the spanning
tree instance as determined by the Spanning Tree Protocol
as executed by this node. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.76.28.1.6.1.16.2 |
mstiBridgeRegionalRootMSTI Regional Root Identifier value for the Instance. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.76.28.1.6.1.16.3 |
stpPortTableA table that contains port-specific information
for the Spanning Tree Protocol. SEQUENCE OF StpPortEntry .1.3.6.1.4.1.171.10.76.28.1.6.2 |
stpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. StpPortEntry .1.3.6.1.4.1.171.10.76.28.1.6.2.1 |
stpPortThe Port number of the port for which this entry contains
spanning tree information.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.6.2.1.1 |
stpPortStatusCurrent state of the Port which can be changed to either
Disabled or Enabled for ALL spanning tree
instances. Setting this object will override the port's
status in any of the MSTI contextsrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.2.1.2 |
stpPortPriorityThe four most significant bits of the Port Identifier
of the Spanning Tree instance can be modified by setting
the CistPortPriority value. The values that are set for Port
Priority must be in steps of 16.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.6.2.1.3 |
stpAdminPortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port. Writing a value of '0' assigns the
automatically calculated default Path Cost value to
the ohter object stpPortPathCost. If the default
Path Cost is being used,this object returns '0' when
read.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.6.2.1.4 |
stpPortPathCostThe contribution of this port to the path cost of
paths towards the CIST Root which include this port.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.6.2.1.5 |
stpPortProtocolMigrationIndicates the Protocol migration state of this Port.
When operating in RSTP/MSTP (version >= 2) mode, writing
TRUE(1) to this object forces this port to transmit MSTP
BPDUs without instance information.
Any other operation on this object has no effect and
it always returns FALSE(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.6.2.1.6 |
stpPortEdgeThis parameter when TRUE(1) indicates that detection of a port
as Edge Port happens automatically and FALSE(2)
indicates that this feature is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.2.1.7 |
stpPortAdminP2PThe administrative point-to-point status of the LAN segment
attached to this port. A value of forceTrue(0) indicates that
this port should always be treated as if it is connected to
a point-to-point link. A value of forceFalse(1) indicates
that this port should be treated as having a shared media
connection. A value of auto(2) indicates that this port is
considered to have a point-to-point link if it is an Aggregator
and all of its members are aggregatable, or if the MAC entity
is configured for full duplex operation, either through
auto-negotiation or by management means.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.2.1.8 |
stpPortRestrictedRoleA Boolean value set by management. If TRUE causes the Port not
to be selected as Root Port for the CIST or any MSTI, even it has
the best spanning tree priority vector. Such a Port will be selected
as an Alternate Port after the Root Port has been selected. This
parameter should be FALSE by default. If set it can cause lack of
spanning tree connectivity. It is set by a network administrator to
prevent bridges external to a core region of the network influencing
the spanning tree active topology, possibly because those bridges are
not under the full control of the administrator.
This administrator configuration is also known as 'Root Guard'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.6.2.1.9 |
stpPortRestrictedTCNA Boolean value set by management. If TRUE causes the Port not
to propagate received topology change notifications and topology
changes to other Ports. This parameter should be FALSE by default.
If set it can cause temporary loss of connectivity after changes in
a spanning trees active topology as a result of persistent
incorrectly learnt station location information. It is set by a
network administrator to prevent bridges external to a core region of
the network causing address flushing in that region, possibly because
those bridges are not under the full control of the administrator or
MAC_Operational for the attached LANs transitions frequently.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.6.2.1.10 |
stpPortHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node in units
of hundredths of a second.rw Timeout .1.3.6.1.4.1.171.10.76.28.1.6.2.1.11 |
stpPortStateCurrent state of the Port as defined by the Common
spanning tree protocol.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.2.1.12 |
stpPortFowardBPDUThis object is for enabling or disabling forward BPDU.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.2.1.13 |
mstConfigurationIdentification OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.6.3 |
mstiConfigurationNameThe Name for the Region's configuration. By Default
Region Name will be equal to the Bridge Mac Address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.1 |
mstiRevisionLevelVersion of the MST Region.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.3.2 |
mstCistVlanMappedA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.3 |
mstCistVlanMapped2kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 1024 through 2047. The
first octet corresponds to VLANs with VlanIndex values
1024 through 1031; the second octet to VLANs 1032
through 1039 etc. The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4095.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.4 |
mstCistVlanMapped3kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 2048 through 3071. The
first octet corresponds to VLANs with VlanIndex values
of 2048 through 2055; the second octet to VLANs 2056
through 2063 etc. The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4095.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.5 |
mstCistVlanMapped4kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 3072 through 4095. The
first octet corresponds to VLANs with VlanIndex values
3072 through 3079; the second octet to VLANs 3080
through 3087 etc. The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4095.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.6 |
mstVlanMstiMappingTableThis table contains one entry for each instance of MSTP.
This table maintains context ID as one more index to
support Multiple Instances. SEQUENCE OF MstVlanMstiMappingEntry .1.3.6.1.4.1.171.10.76.28.1.6.3.7 |
mstVlanMstiMappingEntryA conceptual row containing the status of the MSTP instance. MstVlanMstiMappingEntry .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1 |
mstInstanceIndexAn arbitrary integer within the range from 1 to the value of
Max Instance Number that uniquely identifies an instance.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1.1 |
mstSetVlanListA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
The set of vlans configured by management to map for this
Instance. If the VlanId to Instance Mapping has to be known
then any one of the VlanMapped object should be used.If a
vlan is already mapped to this Instance, it may not be mapped
again. This object is used only for SET operation.
GET Operation returns null values.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1.2 |
mstResetVlanListA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
The set of vlans configured by management to unmap from this
Instance. A vlan may not be unmapped from this instance if
it is not already mapped to this Instance. This object is
used only for SET operation.GET Operation returns null values.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1.3 |
mstInstanceVlanMappedA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1.4 |
mstInstanceVlanMapped2kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 1024 through 2047. The
first octet corresponds to VLANs with VlanIndex values
1024 through 1031; the second octet to VLANs 1032
through 1039 etc. The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4095.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1.5 |
mstInstanceVlanMapped3kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 2048 through 3071. The
first octet corresponds to VLANs with VlanIndex values
of 2048 through 2055; the second octet to VLANs 2056
through 2063 etc. The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4095.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1.6 |
mstInstanceVlanMapped4kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 3072 through 4095. The
first octet corresponds to VLANs with VlanIndex values
3072 through 3079; the second octet to VLANs 3080
through 3087 etc. The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this MSTP instance,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4095.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.6.3.7.1.7 |
stpInstance OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.6.4 |
mstCistBridgePriorityThe writable portion of the MSTI Bridge Identifier.
comprising of the first two octets.
The values that are set for Bridge Priority must be
in steps of 4096.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.4.1 |
mstCistStatusThe administrative status requested by management for the MST
feature. The value enabled(1) indicates that Mst should be enabled
in the device on all ports. The value disabled(2) indicates that
Mst should be disabled in the device on all ports. The object can
be set to enabled(1) if and only if, fsMIMstSystemControl set to start.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.4.2 |
mstMstiBridgeTableTable containing Bridge Information specific to Spanning
Tree Instance. This table maintains context ID as one
more index to support Multiple Instances. SEQUENCE OF MstMstiBridgeEntry .1.3.6.1.4.1.171.10.76.28.1.6.4.3 |
mstMstiBridgeEntryEntry indicating the Bridge Information. MstMstiBridgeEntry .1.3.6.1.4.1.171.10.76.28.1.6.4.3.1 |
mstMstiInstanceIndexSpanning Tree Instance to which the information belongs.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.4.3.1.1 |
mstMstiBridgePriorityThe writable portion of the MSTI Bridge Identifier.
comprising of the first two octets.
The values that are set for Bridge Priority must be
in steps of 4096.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.4.3.1.2 |
mstMstiStatusThe administrative status requested by management for the MST
feature. The value enabled(1) indicates that Mst should be enabled
in the device on all ports. The value disabled(2) indicates that
Mst should be disabled in the device on all ports. The object can
be set to enabled(1) if and only if, fsMIMstSystemControl set to start.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.4.3.1.3 |
stpInstancePortTable OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.6.5 |
mstCistPortTableThis table contains Common Spanning Tree Port
Information. SEQUENCE OF MstCistPortEntry .1.3.6.1.4.1.171.10.76.28.1.6.5.1 |
mstCistPortEntryA list of information maintained by every port for
Common Spanning tree. MstCistPortEntry .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1 |
mstCistPortThe Port number of the port for which this entry contains
spanning tree information. Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1.1 |
mstCistPortDesignatedBridgeThe unique Bridge Identifier of the bridge which this port
considers to be the Designated Bridge for the port's segment.ro BridgeId .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1.2 |
mstCistPortAdminPathCostThe contribution of this port to the path cost of
paths towards the MSTI Root which include this port.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1.3 |
mstCistPortPathCostThe contribution of this port to the path cost of
paths towards the MSTI Root which include this port.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1.4 |
mstCistPortPriorityThe four most significant bits of the Port Identifier
for a given Spanning Tree instance can be modified
independently for each Spanning Tree instance
supported by the Bridge. The values that are set for Port
Priority must be in steps of 16.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1.5 |
mstCistForcePortStateCurrent state of the Port which can be changed to either
Disabled or Enabled for the specific spanning tree
instance. This object can be set to enabled only if the
'fsMIMstCistForcePortState' is set to 'enabled' for this portro Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1.6 |
mstCistCurrentPortRoleCurrent Port Role of the port for this spanning
tree instance.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.5.1.1.7 |
mstMstiPortTableThis table contains Spanning Tree Instance Specific Port
Information. SEQUENCE OF MstMstiPortEntry .1.3.6.1.4.1.171.10.76.28.1.6.5.2 |
mstMstiPortEntryA list of information maintained by every port for each
and every spanning tree instance. MstMstiPortEntry .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1 |
mstMstiPortThe Port number of the port for which this entry contains
spanning tree information. Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1.1 |
mstMstiPortDesignatedBridgeThe unique Bridge Identifier of the bridge which this port
considers to be the Designated Bridge for the port's segment.ro BridgeId .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1.2 |
mstMstiPortAdminPathCostThe contribution of this port to the path cost of
paths towards the MSTI Root which include this port.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1.3 |
mstMstiPortPathCostThe contribution of this port to the path cost of
paths towards the MSTI Root which include this port.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1.4 |
mstMstiPortPriorityThe four most significant bits of the Port Identifier
for a given Spanning Tree instance can be modified
independently for each Spanning Tree instance
supported by the Bridge. The values that are set for Port
Priority must be in steps of 16.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1.5 |
mstMstiForcePortStateCurrent state of the Port which can be changed to either
Disabled or Enabled for the specific spanning tree
instance. This object can be set to enabled only if the
'fsMIMstCistForcePortState' is set to 'enabled' for this portro Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1.6 |
mstMstiCurrentPortRoleCurrent Port Role of the port for this spanning
tree instance.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.6.5.2.1.7 |
companyDot1qVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.7 |
dot1qVlanManagementOnOffEnable/Disable management VLAN mechanism.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.7.2 |
dot1qVlanManagementidThe management VLAN ID, which will allow to forward packets of that VLAN to CPU.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.7.3 |
dot1qVlanAsyOnOffEnable/Disable IEEE 802.1Q Asymmetric VLANrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.7.5 |
dot1qVlanTableA table containing static configuration information for
each VLAN configured into the device by (local or
network) management. All entries are permanent and will
be restored after the device is reset. SEQUENCE OF Dot1qVlanEntry .1.3.6.1.4.1.171.10.76.28.1.7.6 |
dot1qVlanEntryInformation for a VLAN configured into the
device by (local or network) management. Dot1qVlanEntry .1.3.6.1.4.1.171.10.76.28.1.7.6.1 |
dot1qVlanNameAn administratively assigned string, which may be used
to identify the VLAN.rw SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.7.6.1.1 |
dot1qVlanEgressPortsThe set of ports which are permanently assigned to the
egress list for this VLAN by management. Changes to a
bit in this object affect the per-port per-VLAN
Registrar control for Registration Fixed for the
relevant GVRP state machine on each port. A port may
not be added in this set if it is already a member of
the set of ports in dot1qVlanForbiddenEgressPorts. The
default value of this object is a string of zeros of
appropriate length, indicating not fixed.rw PortList .1.3.6.1.4.1.171.10.76.28.1.7.6.1.2 |
dot1qVlanForbiddenPortsThe set of ports which are prohibited by management
from being included in the egress list for this VLAN.
Changes to this object that cause a port to be included
or excluded affect the per-port per-VLAN Registrar
control for Registration Forbidden for the relevant GVRP
state machine on each port. A port may not be added in
this set if it is already a member of the set of ports
in dot1qVlanEgressPorts. The default value of
this object is a string of zeros of appropriate length,
excluding all ports from the forbidden set.rw PortList .1.3.6.1.4.1.171.10.76.28.1.7.6.1.3 |
dot1qVlanUntaggedPortsThe set of ports which should transmit egress packets
for this VLAN as untagged. The default value of this
object for the default VLAN (dot1qVlanIndex = 1) is a string
of appropriate length including all ports. There is no
specified default for other VLANs. If a device agent cannot
support the set of ports being set then it will reject the
set operation with an error. An example might be if a
manager attempts to set more than one VLAN to be untagged
on egress where the device does not support this IEEE 802.1Q
option.rw PortList .1.3.6.1.4.1.171.10.76.28.1.7.6.1.4 |
dot1qVlanAdvertisementStatusEnable/Disable Advertisement Status of the IEEE 802.1Q VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.7.6.1.5 |
dot1qVlanRowStatusThe status of a row in dot1qVlanTable. By setting this object, new
entries can be created in dot1qVlanTable and existing entries can be
removed from dot1qVlanTable. It can be used as specified in the SNMP
v2 standard.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.7.6.1.6 |
dot1qVlanUngisterMCFilterTableThis table contains the list of ports through which
a router, in a particular VLAN is reachable. SEQUENCE OF Dot1qVlanUngisterMCFilterEntry .1.3.6.1.4.1.171.10.76.28.1.7.8 |
dot1qVlanUngisterMCFilterEntryA list of multicast filter mode information for each VLAN ID. Dot1qVlanUngisterMCFilterEntry .1.3.6.1.4.1.171.10.76.28.1.7.8.1 |
dot1qVlanUngisterMCFilterVlanIdPer Vlan to configure multicast filtering function.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.7.8.1.1 |
dot1qVlanUngisterMCFiltermodeFilter unknown multicast frames or normal operation(i.e. forwarding)rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.7.8.1.2 |
dot1qVlanPVIDAutoAssignOnOffEnable/Disable VLAN PVID auto assignmentrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.7.9 |
companyLA OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.8 |
laSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.8.1 |
laStatusSets the Link Aggregation Module administrative status as
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.8.1.2 |
laPortChannelTableA Port-channel is created through ifMain table.
After the creation of the port-channel, corresponding logical
interface will be created in the ifMain table.
This Port-channel table is indexed through Key values and allows to
configure link selection policy and the Mac address for
the port-channel. All other objects in this table displays
the details of the port-channel. SEQUENCE OF LaPortChannelEntry .1.3.6.1.4.1.171.10.76.28.1.8.1.3 |
laPortChannelEntryThere is one entry in this table for each created
port-channel port. LaPortChannelEntry .1.3.6.1.4.1.171.10.76.28.1.8.1.3.1 |
laPortChannelIfIndexThe index of the port-channel(Aggregator's
interface index).ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.8.1.3.1.1 |
laPortChannelMemberListMember Port list of the port channel. Add the ports as a
aggregation member associated of a port-channel.rw PortList .1.3.6.1.4.1.171.10.76.28.1.8.1.3.1.2 |
laPortChannelModeCurrent Operating Channel Mode of the port channel
Lacp(1) - forcing the port to negotiate with the
partner.
manual(2) - force the port to enable channeling (Manual).
disable(3) - channeling is disabled.rw PortLaMode .1.3.6.1.4.1.171.10.76.28.1.8.1.3.1.3 |
laPortChannelMasterPortThe master port of the port-channel.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.8.1.3.1.4 |
laAlgorithmSets the Link Aggregation load balance algorithm.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.8.1.4 |
laPortControl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.8.2 |
laPortControlTableA table that contains Link Aggregation Control
configuration information about every
Aggregation Port associated with this device.
A row appears in this table for each physical port. SEQUENCE OF LaPortControlEntry .1.3.6.1.4.1.171.10.76.28.1.8.2.1 |
laPortControlEntryA list of Link Aggregation Control configuration
parameters for each Aggregation Port on this device. LaPortControlEntry .1.3.6.1.4.1.171.10.76.28.1.8.2.1.1 |
laPortControlIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.8.2.1.1.1 |
laPortActorPortPriorityThe priority value assigned to this Aggregation Port.
This 16-bit value is read-write.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.8.2.1.1.2 |
laPortActorActivityThis object indicates LACP_Activity to this Aggregation Port.
LACP can be configured in one of two modes: active or passive.
In active mode it will always send frames along the configured links.
If the actor and partner are both in passive mode, they do not
exchange LACP packets.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.8.2.1.1.3 |
laPortActorTimeoutThis object indicates LACP_Timeout to this Aggregation Port.
short(1) - LACP Timeout 3 seconds.
long (2) - LACP Timeout 90 seconds.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.8.2.1.1.4 |
companyStaticMAC OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.9 |
staticDisableAutoLearnSet on to disable Auto Learning Excluding Uplink Port and
set off to enable Auto Learning.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.9.1 |
staticAutoLearningListThe set of the device's member ports that belong
to the Static MAC auto learning enable/disable.
For example, when Disable Auto Learning is enable,
the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means
from port 1 to port 4 are not in auto learning state,
the other ports are in auto learning state. It can be
set up when Disable Auto Learning is enable.rw PortList .1.3.6.1.4.1.171.10.76.28.1.9.2 |
staticTableA list of the Static MACs SEQUENCE OF StaticEntry .1.3.6.1.4.1.171.10.76.28.1.9.3 |
staticEntryA Static MAC entry containing the mac and forwarding port. StaticEntry .1.3.6.1.4.1.171.10.76.28.1.9.3.1 |
staticVlanIDThe VLAN ID of the static MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.9.3.1.1 |
staticMacThe MAC address associated of the static MAC entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.9.3.1.2 |
staticPortThe forwarding port of the static MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.9.3.1.3 |
staticStatusThe status of an entry in the Static MAC Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available. The trunk member port can not set up static MAC.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.9.3.1.4 |
autoFdbTableA list of the Auto Fdb SEQUENCE OF AutoFdbEntry .1.3.6.1.4.1.171.10.76.28.1.9.4 |
autoFdbEntryA auto fdb entry containing the ipaddress AutoFdbEntry .1.3.6.1.4.1.171.10.76.28.1.9.4.1 |
autoFdbIPAddressThe IpAddress of the autoFdbEntry.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.9.4.1.1 |
autoFdbVlanIDThe VlanID of the autoFdbEntry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.9.4.1.2 |
autoFdbMacAddressThe Mac Address of the autoFdbEntry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.9.4.1.3 |
autoFdbPortThe Port of the autoFdbEntry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.9.4.1.4 |
autoFdbTimeStampThe Time Stamp of the autoFdbEntry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.9.4.1.5 |
autoFdbStatusThe status of an entry in the Auto Fdb Table. Only a subset
of the rowstatus variables (createAndGo, createAndWait,destroy)
are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.9.4.1.6 |
staticVlanBaseTable OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.9.5 |
staticVlanBaseAutoLearnList1kA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
For each VLAN that is mapped to this Auto Learn,
the bit corresponding to that VLAN is set to '1'.
Write AutoLearnList1k use 256 character, and conform
to the foregoing rules.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.9.5.1 |
staticVlanBaseAutoLearnList2kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 1025 through 2048.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this Auto Learn.
Write AutoLearnList2k use 256 character, and conform
to the foregoing rules.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.9.5.2 |
staticVlanBaseAutoLearnList3kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 2049 through 3072.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this Auto Learn
the bit corresponding to that VLAN is set to '1'.
Write AutoLearnList3k use 256 character, and conform
to the foregoing rules.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.9.5.3 |
staticVlanBaseAutoLearnList4kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 3073 through 4094.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this Auto Learn
the bit corresponding to that VLAN is set to '1'.
Write AutoLearnList4k use 256 character, and conform
to the foregoing rules.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.9.5.4 |
staticVlanBaseEnableAutoLearnSet enable vlan list to auto learn, and range 1-4094.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.9.5.5 |
staticVlanBaseDisableAutoLearnSet disable vlan list to auto learn, and range 1-4094.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.9.5.6 |
companyIgsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.10 |
igsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.10.1 |
igsStatusEnables or disables IGMP snooping in the system.
When set to 'enabled', the IGS module starts
protocol operations.
When set to 'disabled', the IGS module stops performing
protocol operations.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.1.1 |
igsRouterPortPurgeIntervalThis is the interval (in seconds) after which a learnt
router port entry will be purged. For each router port learnt,
this timer runs for 'RouterPortPurgeInterval' seconds.When the
timer expires, the learnt router port entry is purged. However
if control messages are received from the router before the
timer expiry, then the timer is restarted.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.1.2 |
igsHostPortPurgeIntervalThis is the interval (in seconds) after which a learnt
port entry will be purged. For each port on which report
has been received this timer runs for 'PortPurgeInterval'
seconds. This timer will be restarted whenever a report
message is received from a host on the specific port. If
the timer expires, then , the learnt port entry will
be purged from the multicast group.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.1.3 |
igsDataDrivenLearningMaxLearnedEntryVlaueThe maximum data driven learning entry value.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.10.1.8 |
igsReportToAllPortEnables or disables IGMP snooping in the system.
When set to 'enabled', the IGS module forwards packets
to report to all port.
When set to 'disabled', the IGS module forwards packets
to router port only.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.1.9 |
igsVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.10.3 |
igsVlanRouterTableThis table contains the list of ports through which
a router, in a particular VLAN is reachable. SEQUENCE OF IgsVlanRouterEntry .1.3.6.1.4.1.171.10.76.28.1.10.3.3 |
igsVlanRouterEntryContains the VLAN ID and list of ports on which
routers are present in the VLAN. IgsVlanRouterEntry .1.3.6.1.4.1.171.10.76.28.1.10.3.3.1 |
igsVlanRouterVlanIdVLAN ID of the ports through which router is reachable.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.3.3.1.1 |
igsVlanRouterPortListList of ports on which routers are present.
These router ports are learnt through control messages
received from routers, and can also be configured
statically.ro PortList .1.3.6.1.4.1.171.10.76.28.1.10.3.3.1.2 |
igsVlanFilterTableThis table contains configuration of snooping
on specific Vlans. This Table is valid only when VLAN is
enabled in the system. SEQUENCE OF IgsVlanFilterEntry .1.3.6.1.4.1.171.10.76.28.1.10.3.4 |
igsVlanFilterEntryContains snooping status , version and fast leave
configuration for a specific VLAN. IgsVlanFilterEntry .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1 |
igsVlanFilterVlanIdIndex of IgsVlanFilterEntry. This object indicates the VLAN ID for which
the snooping configurations in IgsVlanFilterEntry is to be done.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.1 |
igsVlanSnoopStatusThis object allows you to enable/disable IGS function on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.2 |
igsVlanQuerierIndicates whether the switch is configured as a querier in the VLANro Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.3 |
igsVlanCfgQuerierThe snooping switch can be configured as a querier via this object
to send out IGMP general queries when IGMP routers are not present in the VLAN.
When set to 'enabled', the switch will generate general queries.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.4 |
igsVlanQueryIntervalThis is the interval (in seconds) for which the switch
sends general queries when it is configured as a querier for
the VLAN. A switch should be configured as a querier for a VLAN
only when there is no queriers in the network.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.5 |
igsVlanRtrPortListList of ports which are configured statically as router portsrw PortList .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.6 |
igsVlanFbdRtrPortListList of ports which can be configured statically as forbidden router ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.7 |
igsVlanFastLeaveEnables or disables fast leave for the VLAN. When it is
'disabled',on reception of a leave message, the switch checks
if they are any interested receivers for the group by sending
a group specific query before removing the port from the
forwarding table. If set to 'enabled', the switch does not
send a group specific query and immediately removes the port
from the forwarding table.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.8 |
igsVlanDataDrivenLearningStatusThis object allows you to enable/disable
Data Driven Learning function on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.9 |
igsVlanQuerierVersionStatusThis object allows you to enable/disable
Querier Version function on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.10 |
igsVlanDataDrivenLearningAgeOutStatusThis object allows you to enable/disable
Data Driven Learning Age Out State on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.11 |
igsVlanReportSuppressionEnables or disables Report suppression in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.12 |
igsVlanRobustnessValueWhen the switch receives leave message on a port, it
sends group specific query to check if there are any other
interested receivers for the group. This attribute defines
the maximum number of queries sent by the switch before deleting
the port from the group membership information in the forwarding
database. If the maximum retry count exceeds 'igsRobustnessValue',
then the port will be deleted from the multicast group membership
information in the forwarding database and received leave message
will be forwarded onto the router ports if there are no
interested receivers for the group.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.13 |
igsVlanGrpQueryIntervalThe value of this attribute defines the time period with which
the switch will send group specific queries on a port to check
if there is any intersted receivers. The switch will send
'igsRobustnessValue' queries before removing the port from the
group membership information in the forwarding database.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.14 |
igsVlanQueryMaxResponseTimeThe maximum query response time advertised in IGMPv2 general
queries on this interface.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.10.3.4.1.15 |
igsVlanMulticastGroupTableThis table contains MAC based multicast forwarding
information. SEQUENCE OF IgsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.76.28.1.10.3.5 |
igsVlanMulticastGroupEntryThis table contains VLAN ID, multicast group MAC address and the
list of ports onto which the multicast data packets for group
should be forwarded. IgsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.76.28.1.10.3.5.1 |
igsVlanMulticastGroupVlanIdVLAN ID pertaining to the Multicast forwarding entryro Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.3.5.1.1 |
igsVlanMulticastGroupIpAddressMulticast group IP address. This object indicates that a
multicast group address was learned in the switch and be represented
as IP address format.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.10.76.28.1.10.3.5.1.2 |
igsVlanMulticastGroupMacAddressMulticast group MAC address. This object indicates that a
multicast group address was learned in the switch and be represented
as MAC address format.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.10.3.5.1.3 |
igsVlanMulticastGroupPortListList of ports onto which the multicast data
packets destined for this group will be forwarded.ro PortList .1.3.6.1.4.1.171.10.76.28.1.10.3.5.1.4 |
igsAccessAuth OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.10.5 |
igsAccessAuthTableThis table is used to manage the IGMP Authentication
function of the switch. SEQUENCE OF IgsAccessAuthEntry .1.3.6.1.4.1.171.10.76.28.1.10.5.1 |
igsAccessAuthEntryContains management entities for IGMP Authentication
function. IgsAccessAuthEntry .1.3.6.1.4.1.171.10.76.28.1.10.5.1.1 |
igsAccessAuthPortIndexThe port index of igsAccessAuthTable which
indicates the port to be configured.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.5.1.1.1 |
igsAccessAuthStateThis object can be configured to set IGMP Authentication
state to enabled/disabled on each port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.10.5.1.1.2 |
igsHost OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.10.6 |
igsHostTableThis table is used to manage
the IGMP Host based Fast Leave function of the switch. SEQUENCE OF IgsHostEntry .1.3.6.1.4.1.171.10.76.28.1.10.6.1 |
igsHostEntryContains management entities for
IGMP Host based fast leave function. IgsHostEntry .1.3.6.1.4.1.171.10.76.28.1.10.6.1.1 |
igsHostTableVLANIDVLAN ID of Host table entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.6.1.1.1 |
igsHostTableGroupAddressGroup address of Host table entry.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.10.76.28.1.10.6.1.1.2 |
igsHostTablePortPort number of Host table entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.10.6.1.1.3 |
igsHostTableHostIPAddressHost IP address of Group in Host table entry.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.10.76.28.1.10.6.1.1.4 |
companyGVRPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.11 |
gvrpGVRPGlobalSettingsOnOffEnable/Disable GVRP mechanism.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.11.1 |
gvrpSettingsJoinTimeThe Join Time value assigned to this Join Time field.
This 16-bit value is read-write.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.11.2 |
gvrpSettingsLeaveTimeThe Leave Time value assigned to this Leave Time field.
This 16-bit value is read-write.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.11.3 |
gvrpSettingsLeaveAllTimeThe Leave_All Time value assigned to this Leave_All Time field.
This 16-bit value is read-write.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.11.4 |
gvrpSettingsTableA table containing static configuration information for
each GVRP configured into the device by (local or
network) management. All entries are permanent and will
be restored after the device is reset. SEQUENCE OF GvrpSettingsEntry .1.3.6.1.4.1.171.10.76.28.1.11.5 |
gvrpSettingsEntryInformation for a GVRP configured into the
device by (local or network) management. GvrpSettingsEntry .1.3.6.1.4.1.171.10.76.28.1.11.5.1 |
gvrpSettingsPortControlIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.11.5.1.1 |
gvrpSettingsPVIDThe PVID value assigned to this Aggregation Port.
This 16-bit value is read-write.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.11.5.1.2 |
gvrpSettingsGVRPStateEnable/Disable GVRP State to this Aggregation Port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.11.5.1.3 |
gvrpSettingsIngressCheckingEnable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.11.5.1.4 |
gvrpSettingsAcceptableFrameTypeChose types All Frames/Tagged to this Aggregation Port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.11.5.1.5 |
companyQoSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12 |
cosScheduleMechanismQueuing mechanism.
strictPriority(1) : Strict Priority
wrr(2) : Weighted Round Robin
Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues.
Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS3 spec. Queues with higher weights get bandwidth before than other queues with less weights.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.1 |
cosOutputSchedule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.2 |
cosClassTableA list of cosOutputSchedule. SEQUENCE OF CosClassEntry .1.3.6.1.4.1.171.10.76.28.1.12.2.1 |
cosClassEntryA list of cosOutputClass Weight. CosClassEntry .1.3.6.1.4.1.171.10.76.28.1.12.2.1.1 |
cosClassIndexA index of class 0 ~ 7.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.2.1.1.1 |
cosWeightcos weightrw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.2.1.1.2 |
qosDefaultUserPri OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.4 |
qosDefaultUserPriTableA list of 802.1p port default priority Entries. SEQUENCE OF QosDefaultUserPriEntry .1.3.6.1.4.1.171.10.76.28.1.12.4.1 |
qosDefaultUserPriEntryA list of 802.1p port default priority priorities. QosDefaultUserPriEntry .1.3.6.1.4.1.171.10.76.28.1.12.4.1.1 |
qosDefaultUserPriPortIndexA port identifier that is in the range of 1 to ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.4.1.1.1 |
qosDefaultPriorityFor ingress untagged packets, the per port 'Default Priority'
setting will be applied to packets of each port to provide
port-based traffic prioritization when 802.1p is enabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.4.1.1.2 |
qosEffectiveDefaultPriorityFor ingress untagged packets, the per port 'Effective Default
Priority' setting will be applied to packets of each port to
provide port-based traffic prioritization when 802.1p is enabled.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.4.1.1.3 |
qosUserPriority OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.5 |
qosUserPriorityTableA table mapping evaluated User Priority to Traffic
Class, for forwarding by the bridge. Traffic class is a
number in the range (0..3). SEQUENCE OF QosUserPriEntry .1.3.6.1.4.1.171.10.76.28.1.12.5.1 |
qosUserPriEntryUser Priority to Traffic Class mapping. QosUserPriEntry .1.3.6.1.4.1.171.10.76.28.1.12.5.1.1 |
qosUserPriIndexFor ingress tagged packets, D-Link Smart Switches will refer
to these information and prioritize them with 4 different priority queues.
If 802.1p is enabled.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.5.1.1.1 |
qosUserPriClassThe User Class the received frame is mapped to.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.5.1.1.2 |
qosDiffServTOS OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.6 |
qosDSCPTOSModeSettings of Qos mode:
DSCP QoS or TOS Qos.
IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic.
DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.6.1 |
qosDiffServTypeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.6.2 |
qosDiffServType00DiffServ Type 0 : IP ToS value = 0rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.1 |
qosDiffServType01DiffServ Type 01 : IP ToS value = 4rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.2 |
qosDiffServType02DiffServ Type 02 : IP ToS value = 8rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.3 |
qosDiffServType03DiffServ Type 03 : IP ToS value = 12rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.4 |
qosDiffServType04DiffServ Type 04 : IP ToS value = 16rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.5 |
qosDiffServType05DiffServ Type 05 : IP ToS value = 20rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.6 |
qosDiffServType06DiffServ Type 06 : IP ToS value = 24rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.7 |
qosDiffServType07DiffServ Type 07 : IP ToS value = 28rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.8 |
qosDiffServType08DiffServ Type 08 : IP ToS value = 32rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.9 |
qosDiffServType09DiffServ Type 09 : IP ToS value = 36rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.10 |
qosDiffServType10DiffServ Type 10 : IP ToS value = 40rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.11 |
qosDiffServType11DiffServ Type 11 : IP ToS value = 44rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.12 |
qosDiffServType12DiffServ Type 12 : IP ToS value = 48rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.13 |
qosDiffServType13DiffServ Type 13 : IP ToS value = 52rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.14 |
qosDiffServType14DiffServ Type 14 : IP ToS value = 56rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.15 |
qosDiffServType15DiffServ Type 15 : IP ToS value = 60rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.16 |
qosDiffServType16DiffServ Type 16 : IP ToS value = 64rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.17 |
qosDiffServType17DiffServ Type 17 : IP ToS value = 68rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.18 |
qosDiffServType18DiffServ Type 18 : IP ToS value = 72rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.19 |
qosDiffServType19DiffServ Type 19 : IP ToS value = 76rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.20 |
qosDiffServType20DiffServ Type 20 : IP ToS value = 80rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.21 |
qosDiffServType21DiffServ Type 21 : IP ToS value = 84rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.22 |
qosDiffServType22DiffServ Type 22 : IP ToS value = 88rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.23 |
qosDiffServType23DiffServ Type 23 : IP ToS value = 92rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.24 |
qosDiffServType24DiffServ Type 24 : IP ToS value = 96rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.25 |
qosDiffServType25DiffServ Type 25 : IP ToS value = 100rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.26 |
qosDiffServType26DiffServ Type 26 : IP ToS value = 104rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.27 |
qosDiffServType27DiffServ Type 27 : IP ToS value = 108rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.28 |
qosDiffServType28DiffServ Type 28 : IP ToS value = 112rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.29 |
qosDiffServType29DiffServ Type 29 : IP ToS value = 116rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.30 |
qosDiffServType30DiffServ Type 30 : IP ToS value = 120rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.31 |
qosDiffServType31DiffServ Type 31 : IP ToS value = 124rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.32 |
qosDiffServType32DiffServ Type 32 : IP ToS value = 128rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.33 |
qosDiffServType33DiffServ Type 33 : IP ToS value = 132rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.34 |
qosDiffServType34DiffServ Type 34 : IP ToS value = 136rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.35 |
qosDiffServType35DiffServ Type 35 : IP ToS value = 140rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.36 |
qosDiffServType36DiffServ Type 36 : IP ToS value = 144rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.37 |
qosDiffServType37DiffServ Type 37 : IP ToS value = 148rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.38 |
qosDiffServType38DiffServ Type 38 : IP ToS value = 152rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.39 |
qosDiffServType39DiffServ Type 39 : IP ToS value = 156rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.40 |
qosDiffServType40DiffServ Type 40 : IP ToS value = 160rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.41 |
qosDiffServType41DiffServ Type 41 : IP ToS value = 164rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.42 |
qosDiffServType42DiffServ Type 42 : IP ToS value = 168rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.43 |
qosDiffServType43DiffServ Type 43 : IP ToS value = 172rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.44 |
qosDiffServType44DiffServ Type 44 : IP ToS value = 176rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.45 |
qosDiffServType45DiffServ Type 45 : IP ToS value = 180rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.46 |
qosDiffServType46DiffServ Type 46 : IP ToS value = 184rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.47 |
qosDiffServType47DiffServ Type 47 : IP ToS value = 188rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.48 |
qosDiffServType48DiffServ Type 48 : IP ToS value = 192rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.49 |
qosDiffServType49DiffServ Type 49 : IP ToS value = 196rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.50 |
qosDiffServType50DiffServ Type 50 : IP ToS value = 200rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.51 |
qosDiffServType51DiffServ Type 51 : IP ToS value = 204rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.52 |
qosDiffServType52DiffServ Type 52 : IP ToS value = 208rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.53 |
qosDiffServType53DiffServ Type 53 : IP ToS value = 212rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.54 |
qosDiffServType54DiffServ Type 54 : IP ToS value = 216rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.55 |
qosDiffServType55DiffServ Type 55 : IP ToS value = 220rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.56 |
qosDiffServType56DiffServ Type 56 : IP ToS value = 224rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.57 |
qosDiffServType57DiffServ Type 57 : IP ToS value = 228rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.58 |
qosDiffServType58DiffServ Type 58 : IP ToS value = 232rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.59 |
qosDiffServType59DiffServ Type 59 : IP ToS value = 236rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.60 |
qosDiffServType60DiffServ Type 60 : IP ToS value = 240rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.61 |
qosDiffServType61DiffServ Type 61 : IP ToS value = 244rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.62 |
qosDiffServType62DiffServ Type 62 : IP ToS value = 248rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.63 |
qosDiffServType63DiffServ Type 63 : IP ToS value = 252rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.2.64 |
qosTOSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.6.3 |
qosTOSType00TOS 0rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.1 |
qosTOSType01TOS 01rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.2 |
qosTOSType02TOS 02rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.3 |
qosTOSType03TOS 03rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.4 |
qosTOSType04TOS 04rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.5 |
qosTOSType05TOS 05rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.6 |
qosTOSType06TOS 06rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.7 |
qosTOSType07TOS 07rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.6.3.8 |
qosPriSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.7 |
qosPriSettingsTableA list of port priority settings. SEQUENCE OF QosPriSettingsEntry .1.3.6.1.4.1.171.10.76.28.1.12.7.1 |
qosPriSettingsEntryA list of port priority settings Entries. QosPriSettingsEntry .1.3.6.1.4.1.171.10.76.28.1.12.7.1.1 |
qosPriSetPortIndexA port identifier that is in the range of 1 to ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.7.1.1.1 |
qosPriSetPortTypeThe port priority setting type. (ex. none = 0,
802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value
is 2 + 4 = 6.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.7.1.1.2 |
qosAclPrioritySettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.8 |
ipv4aclQosTableA list of priority by acl setting. SEQUENCE OF Ipv4AclQosEntry .1.3.6.1.4.1.171.10.76.28.1.12.8.1 |
ipv4aclQosEntryA list of priority by acl setting entry. Ipv4AclQosEntry .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1 |
ipv4aclQosIndexIndex of priority by acl setting.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.1 |
ipv4aclQosTypeType of priority by acl setting.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.2 |
ipv4aclQosMACAddrDst MAC of priority by acl setting.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.3 |
ipv4aclQosIPAddrDst IP of priority by acl settingrw IpAddress .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.4 |
ipv4aclQosTCPUDPPortDst TCP/UDP port of priority by acl settingrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.5 |
ipv4aclQosVlanIDVLAN ID of priority by acl settingrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.6 |
ipv4aclQosProtocolIp protocol number of priority by acl settingrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.7 |
ipv4aclQosAssignClassBe mapped class of priority by acl setting.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.8 |
ipv4aclQosStatusStatus of priority by acl setting.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.12.8.1.1.9 |
aclQosTableA list of priority by acl setting. SEQUENCE OF AclQosEntry .1.3.6.1.4.1.171.10.76.28.1.12.8.2 |
aclQosEntryA list of priority by acl setting entry. AclQosEntry .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1 |
aclQosIndexIndex of priority by acl setting.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.1 |
aclQosTypeType of priority by acl setting.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.2 |
aclQosMACAddrDst MAC of priority by acl setting.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.3 |
aclQosIPAddrDst IP of priority by acl settingrw IpAddress .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.4 |
aclQosIPv6AddrDst IP of priority by acl setting.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.5 |
aclQosTCPUDPPortDst TCP/UDP port of priority by acl settingrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.6 |
aclQosVlanIDVLAN ID of priority by acl settingrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.7 |
aclQosProtocolIp protocol number of priority by acl settingrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.8 |
aclQosIP6TCIpv6 Traffic Class number of priority by acl settingrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.10 |
aclQosAssignClassBe mapped class of priority by acl setting.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.98 |
aclQosStatusStatus of priority by acl setting.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.12.8.2.1.99 |
cosBandwidthCtrlSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.12.9 |
cosBandwidthCtrlTableA list of cosBandwidthCtrlEntry default priority Entries. SEQUENCE OF CosBandwidthCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.12.9.1 |
cosBandwidthCtrlEntryA list of cosBandwidthCtrlEntry default priority priorities. CosBandwidthCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.12.9.1.1 |
cosBandwidthCtrlPortIndexA port identifier that is in the range of 1 to ifNumber.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.9.1.1.1 |
cosBandwidthCtrlClassIndexA BandwidthCtrlClassIndex identifier that is in the range of 1 to ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.12.9.1.1.2 |
cosBandwidthValueThe BandwidthValue return value.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.12.9.1.1.3 |
companyTrafficMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.13 |
bandwidthCtrlSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.13.1 |
bandwidthCtrlTableA table to control the rate limiting parameters
either for the entire switch or for each interface in the switch. SEQUENCE OF BandwidthCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.13.1.2 |
bandwidthCtrlEntryAn entry appears in this table for each physical
interface in the switch. BandwidthCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.13.1.2.1 |
bandwidthCtrlIndexThe interface index for which the configuration in this
entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.13.1.2.1.1 |
bandwidthCtrlTxThresholdConfigures interface Rate Limit (Packet that can be transferred
on a port at a particular second).
This object's value will take effect on the interface speed. Based
on the operating speed of the port, the rate limit will be applied.
This value can also be affected by the metering. A value of zero(0)
disable rate limiting i.e. sets the port to full speed. The value can
be set between 64~102400(Kbits per second) in FE port, 64~1024000
(Kbits per second) in GE port.rw Integer32 (0 | 64..1024000) .1.3.6.1.4.1.171.10.76.28.1.13.1.2.1.2 |
bandwidthCtrlRxThresholdAllows to configure the limiting value for the maximum number
of receive packets that can be transmitted per second over this
interface. Setting this object to the value zero disables rate
limiting for receive packets on this interface. The value that
can be set for this object is limited by the underlying hardware.
The value can be set between 64~102400(Kbits per second) in FE
port, 64~1024000(Kbits per second) in GE port.rw Integer32 (0 | 64..1024000) .1.3.6.1.4.1.171.10.76.28.1.13.1.2.1.3 |
trafficCtrlSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.13.4 |
trafficCtrlTrapThe trap setting of traffic control.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.13.4.1 |
trafficCtrlTableThe traffic control table. SEQUENCE OF TrafficCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.13.4.2 |
trafficCtrlEntryThe traffic control entry. TrafficCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.13.4.2.1 |
trafficCtrlIndexThe traffic control index.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.13.4.2.1.1 |
trafficCtrlActionModeThe action mode of traffic control.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.13.4.2.1.2 |
trafficCtrlTypeThe control type of traffic control.
(b: Broadcast, m: Multicast, u: Unknown Unicast)rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.13.4.2.1.3 |
trafficCtrlThresholdThe threshold of traffic control.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.13.4.2.1.4 |
trafficCtrlCountDownThe count down value of traffic control.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.13.4.2.1.5 |
trafficCtrlTimeIntervalThe time interval of traffic control.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.13.4.2.1.6 |
companySecurity OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14 |
securityTrustedHost OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.1 |
trustedHostStatusThis object indicates trusted host function is enabled or disabled.
When trusted host function is enabled, D-Link Smart Switches will
only allow hosts which you trust to access and control the switch.
Your local host IP Addresses must be one of the IP Addresses to
avoid disconnection.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.1.1 |
ipv4trustedHostTableA table to configure trusted host in the system.obsolete SEQUENCE OF Ipv4TrustedHostEntry .1.3.6.1.4.1.171.10.76.28.1.14.1.2 |
ipv4trustedHostEntryEach entry in this table represents rules for particular
trusted host.obsolete Ipv4TrustedHostEntry .1.3.6.1.4.1.171.10.76.28.1.14.1.2.1 |
ipv4trustedHostIpAddrThe IP address of host you allow to access to D-Link Smart
Switch.
Your local host IP Addresses must be one of the IP Addresses
to avoid disconnection.roobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.14.1.2.1.1 |
ipv4trustedHostIpMaskUsed to mask with IP address, it allow you set a subnet as a
trusted host entry.roobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.14.1.2.1.2 |
ipv4trustedHostRowStatusThe status of an entry in the Trusted Host Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.1.2.1.3 |
trustedHostTableA table to configure trusted host for in the system. SEQUENCE OF TrustedHostEntry .1.3.6.1.4.1.171.10.76.28.1.14.1.3 |
trustedHostEntryEach entry in this table represents rules for particular
trusted host. TrustedHostEntry .1.3.6.1.4.1.171.10.76.28.1.14.1.3.1 |
trustedHostIPTypeType of IP interface.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.1.3.1.1 |
trustedHostIpAddrThe IP address of host you allow to access to D-Link Smart
Switch.
Your local host IPv4/6 Addresses must be one of the IP Addresses
to avoid disconnection.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.14.1.3.1.2 |
trustedHostIpMaskUsed to mask with IPv4/6 address, it allow you set a subnet as a
trusted host entry.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.14.1.3.1.3 |
trustedHostRowStatusThe status of an entry in the Trusted Host Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.1.3.1.4 |
securityPortSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.2 |
portSecTableA table to control port security features of the device. SEQUENCE OF PortSecEntry .1.3.6.1.4.1.171.10.76.28.1.14.2.1 |
portSecEntryAn entry appears in port security table for each interface
in the system. PortSecEntry .1.3.6.1.4.1.171.10.76.28.1.14.2.1.1 |
portSecIndexThe interface index for which the configuration in this
entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.2.1.1.1 |
portSecStateEnable / disable port security admin state for the interface.
A given ports' dynamic MAC address learning will be stopped such
that the current source MAC addresses entered into the MAC address
forwarding table can not be changed once the port security admin
state is enabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.2.1.1.2 |
portSecMLAConfigures interface port security maximum learning address
numbers.
When given ports' admin state is enabled, allows forwarding
table learning address number. The number can be set 0 to 64.
Note: Set value 0 means cannot learn MAC address.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.2.1.1.3 |
portSecLockAddrModeConfigures port security lock address mode for the interface.
deleteOnReset : The locked addresses will not age out until the Switch has been reset.
deleteOnTimeout : The locked addresses will age out after the aging timer expires.
Permanent : The locked addresses will not age out after the aging timer expires.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.2.1.1.4 |
portSecFDBPermanentTableA table to control port security FDB Permanent of the device. SEQUENCE OF PortSecFDBPermanentEntry .1.3.6.1.4.1.171.10.76.28.1.14.2.2 |
portSecFDBPermanentEntryAn entry appears in port security table for each interface
in the system. PortSecFDBPermanentEntry .1.3.6.1.4.1.171.10.76.28.1.14.2.2.1 |
portSecFDBPermIndexThe index of the port security MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.2.2.1.1 |
portSecFDBPermVlanIDThe VLAN ID of the port security MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.2.2.1.2 |
portSecFDBPermMacThe MAC address associated of the port security MAC entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.2.2.1.3 |
portSecFDBPermPortThe forwarding port of the port security MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.2.2.1.4 |
securityARPSpoofPrevent OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.3 |
aRPSpoofPreventTableA table to control ARP Spoofing prevention for the entire
switch or for each interface in the switch. SEQUENCE OF ARPSpoofPreventEntry .1.3.6.1.4.1.171.10.76.28.1.14.3.1 |
aRPSpoofPreventEntryAn entry appears in this table for each interface
in the system. ARPSpoofPreventEntry .1.3.6.1.4.1.171.10.76.28.1.14.3.1.1 |
aRPSpoofPreventIpAddrSpecifies either the Network or Host address from which the switch
can be managed.
An address 0.0.0.0 indicates 'Any Manager'. IpAddress .1.3.6.1.4.1.171.10.76.28.1.14.3.1.1.1 |
aRPSpoofPreventMacAddressEthernet Mac Address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.3.1.1.2 |
aRPSpoofPreventPortListSpecifies the port numbers through which the authorized manager can
access the switch.
By default the authorized manager is allowed to access the switch
through all the ports.
If a set of ports are configured in the 'PortList', the manager can
access the switch only through the configured ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.14.3.1.1.3 |
aRPSpoofPreventRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.3.1.1.4 |
securitySSL OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.5 |
sslSecurityHttpStatusThis object is for enabling or disabling secure HTTP in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.5.1 |
sslCiphers OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.5.2 |
sslCipherSuiteListThis object is to configure the cipher-suites list.rw Bits .1.3.6.1.4.1.171.10.76.28.1.14.5.2.1 |
securityDhcpServerScreen OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.7 |
dhcpServerScreenEnablePortlistTo enable or disable DHCP Server Screening port list.rw PortList .1.3.6.1.4.1.171.10.76.28.1.14.7.1 |
dhcpServerScreenEnableVlanlistTo enable or disable DHCP Server Screening vlan list.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.7.2 |
dhcpServerScreenLogSuppressDurationDSS Trap Log Suppress Duration.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.7.3 |
filterDHCPServerTableA table to control filter DHCP Server for the entire
switch or for each interface in the switch. SEQUENCE OF FilterDHCPServerEntry .1.3.6.1.4.1.171.10.76.28.1.14.7.4 |
filterDHCPServerEntryAn entry appears in this table for each interface
in the system. FilterDHCPServerEntry .1.3.6.1.4.1.171.10.76.28.1.14.7.4.1 |
filterDHCPServerIpAddrSpecifies either the Network or Host address from which the switch
can be managed.
An address 0.0.0.0 indicates 'Any Manager'. IpAddress .1.3.6.1.4.1.171.10.76.28.1.14.7.4.1.1 |
filterDHCPServerClientMacAddrEthernet Mac Address. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.7.4.1.2 |
filterDHCPServerPortListSpecifies the port numbers through which the authorized manager can
access the switch.
By default the authorized manager is allowed to access the switch
through all the ports.
If a set of ports are configured in the 'PortList', the manager can
access the switch only through the configured ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.14.7.4.1.3 |
filterDHCPServerVlanListSpecifies the port numbers through which the authorized manager can
access the switch.
By default the authorized manager is allowed to access the switch
through all the ports.
If a set of ports are configured in the 'PortList', the manager can
access the switch only through the configured ports.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.7.4.1.4 |
filterDHCPServerRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.7.4.1.99 |
securitySSH OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.8 |
sshSecurityStatusThis object is for enabling or disabling ssh in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.8.1 |
sshMaxAuthFailAttemptsThis object indicates the max auth fail retry attempt times.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.8.2 |
sshSessionKeyRekeyingThis object indicates one SSH session rekey time interval.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.8.3 |
sshMaxSessionThis object indicates max SSH session number supported in system.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.8.4 |
sshConnectionTimeoutThis object indicates SSH connection timeout value.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.8.5 |
sshAuthenMethodPassWordAdminThe object indicates authen method password is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.8.6 |
sshAuthenMethodPubKeyAdminThe object indicates authen method public-key is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.8.7 |
sshAuthenMethodHostKeyAdminThe object indicates authen method host-key is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.8.8 |
sshCipherSuiteListThis object is to configure the cipher-suites list.ro Bits .1.3.6.1.4.1.171.10.76.28.1.14.8.9 |
sshMacSuiteListThis object is to configure the MAC-list.rw Bits .1.3.6.1.4.1.171.10.76.28.1.14.8.10 |
sshPublKeyRSAAdminThe object indicates Public key generating algorithm RSA is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.8.11 |
sshUserInfoTableA table to configure SSH user auth in the system. SEQUENCE OF SshUserInfoEntry .1.3.6.1.4.1.171.10.76.28.1.14.8.12 |
sshUserInfoEntryAn entry to configure user auth in the system. SshUserInfoEntry .1.3.6.1.4.1.171.10.76.28.1.14.8.12.1 |
sshUserInfoIDThe Schedule identifier. The maximum number of Schedule entry is
the number of ports supported PoE function.
The value must be between 1 and 8.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.8.12.1.1 |
sshUserInfoUserNameThe ssh user name associated with the SSH suer Info. entry (e.g., `admin, user').ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.14.8.12.1.2 |
sshUserInfoAuthThe object indicates which auth used by the user.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.8.12.1.3 |
sshUserInfoHostNameThe ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.14.8.12.1.4 |
sshUserInfoHostIpSSH HostBased IP Address of the system.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.14.8.12.1.5 |
securityTrafficSeg OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.9 |
trafficSegTableA Port-channel is created through ifMain table.
After the creation of the port-channel, corresponding logical
interface will be created in the ifMain table.
This Port-channel table is indexed through Key values and allows to
configure link selection policy and the Mac address for
the port-channel. All other objects in this table displays
the details of the port-channel SEQUENCE OF TrafficSegEntry .1.3.6.1.4.1.171.10.76.28.1.14.9.1 |
trafficSegEntryThere is one entry in this table for each created
port-channel port TrafficSegEntry .1.3.6.1.4.1.171.10.76.28.1.14.9.1.1 |
trafficSegIfIndexThe ifIndex of the port-channel(Aggregator's
interface index).ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.14.9.1.1.1 |
trafficSegMemberListPort list of port channel.rw PortList .1.3.6.1.4.1.171.10.76.28.1.14.9.1.1.2 |
securityIpMacPortBinding OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.10 |
impbSettingTableA table to control IP-MAC-Port Binding Setting features of the device. SEQUENCE OF ImpbSettingEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.1 |
impbSettingEntryAn entry appears in IP-MAC-Port Binding Setting table for each interface
in the system. ImpbSettingEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1 |
impbPortIndexSpecifies the port numbers through which the authorized manager can
access the switch.
By default the authorized manager is allowed to access the switch
through all the ports.
If a set of ports are configured in the 'PortList', the manager can
access the switch only through the configured ports.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.1 |
impbPortStateDisable / enable IP-MAC-Port Binding admin state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.2 |
impbPortDHCPSnoopingStateDisable / enable IP-MAC-Port Binding DHCP snooping state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.4 |
impbPortArpInspectionStateSet IP-MAC-Port Binding ARP Inspection state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.5 |
impbPortIpInspectionStateSet IP-MAC-Port Binding IP Inspection state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.6 |
impbPortAllowZeroIPStateDisable / enable IP-MAC-Port Binding Allow-Zero-IP state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.7 |
impbPortForwardDHCPPktStateDisable / enable IP-MAC-Port Binding Forward-DHCP-Packet state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.8 |
impbPortDHCPMaxEntryIPv4Set the maximum number of IPv4 entries that can be learned for the interface.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.9 |
impbPortDHCPMaxEntryIPv6Set the maximum number of IPv6 entries that can be learned for the interface.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.10 |
impbPortNDInspectionStateSet IP-MAC-Port Binding ND Inspection state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.11 |
impbPortProtocolStateSet IP-MAC-Port Binding protocol state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.12 |
impbPortDHCPv4SetVlanListA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
The set of vlans configured by management to map for this
Instance. If the VlanId to Instance Mapping has to be known
then any one of the VlanMapped object should be used.If a
vlan is already mapped to this Instance, it may not be mapped
again. This object is used only for SET operation.
GET Operation returns null values.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.13 |
impbPortDHCPv4VlanList1kA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
For each VLAN that is mapped to this DHCP snooping,
the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.14 |
impbPortDHCPv4VlanList2kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 1025 through 2048.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this DHCPv4 snooping,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4094.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.15 |
impbPortDHCPv4VlanList3kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 2049 through 3072.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this DHCPv4 snooping
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4094.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.16 |
impbPortDHCPv4VlanList4kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 3073 through 4094.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this DHCPv4 snooping,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4094.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.17 |
impbPortDHCPv6SetVlanListA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
The set of vlans configured by management to map for this
Instance. If the VlanId to Instance Mapping has to be known
then any one of the VlanMapped object should be used.If a
vlan is already mapped to this Instance, it may not be mapped
again. This object is used only for SET operation.
GET Operation returns null values.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.18 |
impbPortDHCPv6VlanList1kA string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanIndex values
1 through 8; the second octet to VLANs 9 through
16 etc. The most significant bit of each octet
corresponds to the lowest VlanIndex value in that octet.
For each VLAN that is mapped to this DHCP snooping,
the bit corresponding to that VLAN is set to '1'.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.19 |
impbPortDHCPv6VlanList2kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 1025 through 2048.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this DHCPv6 snooping,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4094.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.20 |
impbPortDHCPv6VlanList3kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 2049 through 3072.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this DHCPv6 snooping
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4094.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.21 |
impbPortDHCPv6VlanList4kA string of octets containing one bit per VLAN for
VLANS with VlanIndex values 3073 through 4094.
The most significant bit of each
octet corresponds to the lowest VlanIndex value in that
octet.
For each VLAN that is mapped to this DHCPv6 snooping,
the bit corresponding to that VLAN is set to '1'.
This object is only instantiated on devices with
support for VlanIndex values up to 4094.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.10.1.1.22 |
impbAutoScanTableA table to control auto scan features of the device. SEQUENCE OF ImpbAutoScanEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.2 |
impbAutoScanEntryAn entry appears in auto scan table for each interface
in the system. ImpbAutoScanEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.2.1 |
impbAutoScanMacAddressThe MAC address associated of the auto scan entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.2.1.1 |
impbAutoScanPortThe port number of the auto scan entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.2.1.2 |
impbAutoScanIpAddressThe IP address associated of the auto scan entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.2.1.3 |
impbAutoScanVlanIdThe VLAN ID of the auto scan entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.2.1.4 |
impbAutoScanBindingDisable / enable IP-MAC-Port Binding for the entry.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.2.1.5 |
impbBindingListTableA table to control Manual IP-MAC-Port Binding white list features of the device. SEQUENCE OF ImpbBindingListEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.3 |
impbBindingListEntryAn entry appears in Manual IP-MAC-Port Binding white list table for each interface
in the system. ImpbBindingListEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.3.1 |
impbBindingListIpAddressThe IP address associated of the Manual IP-MAC-PORT Binding white list entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.3.1.1 |
impbBindingListMacAddressThe MAC address associated of the Manual IP-MAC-PORT Binding white list entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.3.1.2 |
impbBindingListPortThe port number of the Manual IP-MAC-PORT Binding white list entry.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.3.1.3 |
impbBindingListRowStatusThe status of a row in impbBindingListTable. By setting this object, new
entries can be created in impbBindingListTable and existing entries can be
removed from impbBindingListTable. It can be used as specified in the SNMP
v2 standard.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.3.1.4 |
impbBlockListTableA table to control IP-MAC-Port Binding black list of the device. SEQUENCE OF ImpbBlockListEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.4 |
impbBlockListEntryAn entry appears in Manual IP-MAC-Port Binding black list table for each interface
in the system. ImpbBlockListEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.4.1 |
impbBlockListMacAddressThe MAC address associated of the IP-MAC-PORT Binding black list entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.4.1.1 |
impbBlockListVlanIdThe VLAN ID of the IP-MAC-PORT Binding black list entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.4.1.2 |
impbBlockListPortThe port number of the IP-MAC-PORT Binding black list entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.4.1.3 |
impbBlockListIpAddressThe IP address associated of the IP-MAC-PORT Binding black list entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.4.1.4 |
impbBlockListStatusnothing/delete IP-MAC-Port Binding for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.4.1.5 |
impbAutoScanIpAddressFromThe begin for IP address associated of the IP-MAC-PORT Binding auto scan entry.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.14.10.5 |
impbAutoScanIpAddressToThe end for IP address associated of the IP-MAC-PORT Binding auto scan entry.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.14.10.6 |
impbAutoScanStatusNothing / scan IP-MAC-Port Binding auto scan for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.7 |
impbDhcpSnoopingTableA table to display DHCP snooping entries of the device. SEQUENCE OF ImpbDhcpSnoopingEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.8 |
impbDhcpSnoopingEntryAn entry appears in DHCP snooping table for each interface
in the system. ImpbDhcpSnoopingEntry .1.3.6.1.4.1.171.10.76.28.1.14.10.8.1 |
impbDhcpSnoopingMacAddressThe MAC address associated of the DHCP snooping entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.10.8.1.1 |
impbDhcpSnoopingIpAddressThe IP address associated of the DHCP snooping entry.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.14.10.8.1.2 |
impbDhcpSnoopingLeaseTimeThe lease time associated of the DHCP snooping entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.8.1.3 |
impbDhcpSnoopingPortThe port number associated of the DHCP snooping entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.14.10.8.1.4 |
impbRoamingStateDisable / enable IP-MAC-Port Binding roaming state.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.9 |
impbVlanModeStateDisable / enable IP-MAC-Port Binding vlan mode state.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.10 |
impbVlanModeVlanListIP-MAC-Port Binding vlan mode VID list.rw PortList .1.3.6.1.4.1.171.10.76.28.1.14.10.11 |
impbLogStateConfigure IP-MAC-Port Binding log state.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.12 |
impbDHCPv6PrefixDelegationSnoopStateConfigure DHCPv6 PD snooping state.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.13 |
impbBindingtraplogThis object is for enabling or disabling topology change event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.14 |
impbBindingtrap OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.10.15 |
impbBindingtrapsignThe object is for IMPB trap sign in the system. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.76.28.1.14.10.15.1 |
impbAutoScanCurrentStatusShow Auto scan statusro Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.10.16 |
securityAAC OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.11 |
aacAuthenAdminStateThis object indicates the Access Authentication is enable or
disable.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.1 |
aacAuthParamResponseTimeoutTimeout in second for login authentication response.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.2 |
aacAuthParamAttemptThe amount for login authentication, if login failure exceed,
connection or access would be locked.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.3 |
aacAPAuthMethodGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.11.4 |
aacAPLoginMethod OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.1 |
aacAPConsoleLoginMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via local
consolerw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.1.1 |
aacAPTelnetLoginMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via telnet.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.1.2 |
aacAPSSHLoginMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via SSH.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.1.3 |
aacAPHttpLoginMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via HTTP.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.1.4 |
aacAPEnableMethod OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.2 |
aacAPConsoleEnableMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via local
console.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.2.1 |
aacAPTelnetEnableMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via telnet.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.2.2 |
aacAPSSHEnableMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via SSH.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.2.3 |
aacAPHttpEnableMethodSpecify the way which has to execute authentication while login the
system and the method for authentication.Access system via HTTP.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.4.2.4 |
aacServerGroupTableA table that contains informations about server group. SEQUENCE OF AacServerGroupEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.5 |
aacServerGroupEntryA list of the group including servers. AacServerGroupEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.5.1 |
aacServerGroupIndexA value that uniquely identifies this SwAACServerGroupEntry .ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.5.1.1 |
aacServerGroupNameA human-readable text string of the method group.
The name is writable only if Group is new created,
which the value of aacServerGroupRowStatus is 'notReady'.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.11.5.1.2 |
aacServersInGroupThe list of servers in the group, each bit indicates a specified server ID.
The server must be created before including it.rw Bits .1.3.6.1.4.1.171.10.76.28.1.14.11.5.1.3 |
aacServerGroupRowStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.11.5.1.4 |
iPv4aacServerInfoTableA table that contains information about severs.obsolete SEQUENCE OF IPv4AacServerInfoEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.6 |
iPv4aacServerInfoEntryA list of the information of server .obsolete IPv4AacServerInfoEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1 |
iPv4aacServerIndexA value that uniquely identifies this SwAACServerGroupEntry.roobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.1 |
iPv4aacServerIPAddrThe IP address of Serverrwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.2 |
iPv4aacServerAuthProtocolThe authentication protocol provided by the Server.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.3 |
iPv4aacServerAuthPortThe TCP/IP port .rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.4 |
iPv4aacServerAuthKeyThe key used while authentication process.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.5 |
iPv4aacServerTimeoutServer response timeout .rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.6 |
iPv4aacServerRetryCountClient retry count .
(-1: No retry mechanism)rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.7 |
iPv4aacServerRowStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.11.6.1.8 |
aacServerInfoTableA table that contains information about severs. SEQUENCE OF AacServerInfoEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.7 |
aacServerInfoEntryA list of the information of server . AacServerInfoEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1 |
aacServerIndexA value that uniquely identifies this SwAACServerGroupEntry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.1 |
aacServerIPTypeThe IP address of the AAC server IP type
referred to in this table entry. (IPv4=1, IPv6=2)rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.2 |
aacServerIPAddrThe IP address of Serverrw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.3 |
aacServerInterfaceNameSpecifies the interface name when the aacServerIPAddr is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.4 |
aacServerAuthProtocolThe authentication protocol provided by the Server.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.5 |
aacServerAuthPortThe TCP/IP port .rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.6 |
aacServerAuthKeyThe key used while authentication process.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.7 |
aacServerTimeoutServer response timeout .rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.8 |
aacServerRetryCountClient retry count .
(-1: No retry mechanism)rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.9 |
aacServerAccountingPortThe accounting port .rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.10 |
aacServerRowStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.11.7.1.99 |
aacLoginMethodListTableA table that contains information about Login authentication method
lists. SEQUENCE OF AacLoginMethodListEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.8 |
aacLoginMethodListEntryA list of the Authentication methods. AacLoginMethodListEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1 |
aacLoginMethodListIndexA value that identifies this method list.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1.1 |
aacLoginMethodListNameA human-readable text string of the method list.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1.2 |
aacLoginMethod1The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1.3 |
aacLoginMethod2The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1.4 |
aacLoginMethod3The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1.5 |
aacLoginMethod4The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1.6 |
aacLoginMethodListRowStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.11.8.1.7 |
aacEnableMethodListTableA table that contains information about Enable authentication method
lists. SEQUENCE OF AacEnableMethodListEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.9 |
aacEnableMethodListEntryA list of the Authentication methods. AacEnableMethodListEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1 |
aacEnableMethodListIndexA value that identifies this method list.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1.1 |
aacEnableMethodListNameA human-readable text string of the method list.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1.2 |
aacEnableMethod1The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1.3 |
aacEnableMethod2The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1.4 |
aacEnableMethod3The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1.5 |
aacEnableMethod4The type of Login method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1.6 |
aacEnableMethodListRowStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.11.9.1.7 |
aacLocalEnablePasswordThis object is used to set Local Enable Password.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.14.11.10 |
aacAccountingMethodListTableA table that contains information about Accounting authentication method
lists. SEQUENCE OF AacAccountingMethodListEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.11 |
aacAccountingMethodListEntryA list of the Authentication methods. AacAccountingMethodListEntry .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1 |
aacAccountingMethodListIndexA value that identifies this method list.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1.1 |
aacAccountingMethodListNameA human-readable text string of the method list.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1.2 |
aacAccountingMethod1The type of Accounting method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1.3 |
aacAccountingMethod2The type of Accounting method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1.4 |
aacAccountingMethod3The type of Accounting method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1.5 |
aacAccountingMethod4The type of Accounting method list. Besides the pre-defined type, it
also allow to be set user-defined group by aacServerGroupIndex.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1.6 |
aacAccountingMethodListRowStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.14.11.11.1.7 |
aacAccountingServiceIndex OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.11.12 |
aacAccountingServiceNetworkThis object indicates aac Accounting Service Network is radius_only, default_method_list,
method_list_name and disable about Accounting Service Network.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.12.1 |
aacAccountingServiceShellThis object indicates aac Accounting Service Shell is radius_only, default_method_list,
method_list_name and disable about Accounting Service Network.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.12.2 |
aacAccountingServiceSystemThis object indicates aac Accounting System Shell is radius_only, default_method_list,
method_list_name and disable about Accounting Service Network.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.12.3 |
aacAccountingServiceCommand OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.14.11.13 |
aacAccountingServiceCommandAdministratorThis object indicates which method list Accounting Admin Command Service uses.
If the value is -1, it means disabled.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.13.1 |
aacAccountingServiceCommandOperatorThis object indicates which method list Accounting Operator Command Service uses.
If the value is -1, it means disabled.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.13.2 |
aacAccountingServiceCommandPoweruserThis object indicates which method list Accounting PowerUser Command Service uses.
If the value is -1, it means disabled.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.13.3 |
aacAccountingServiceCommandUserThis object indicates which method list Accounting User Command Service uses.
If the value is -1, it means disabled.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.14.11.13.4 |
aacServerPasswordEncryptionThis object is used to configure server password encryption status.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.14.11.14 |
companyACLGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.15 |
aclProfile OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.15.1 |
ipv4aclProfileTableA table to ACL profile .obsolete SEQUENCE OF Ipv4AclProfileEntry .1.3.6.1.4.1.171.10.76.28.1.15.1.1 |
ipv4aclProfileEntryEach entry in this table is a ACL profile.
Index to the table is ACL profile ID.obsolete Ipv4AclProfileEntry .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1 |
ipv4aclProfileNoThe ACL Profile ID. The ID 1 to 50 is user-defined ACL,
and the ID more than 50 is reserved for system-defined ACL.
The user only allow to create user-defined ACL ID.
And system-defined ACL is read only.roobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.1 |
ipv4aclProfileTypeThe ACL Profile type, possible value are
l2 (1) - for MAC-based rule,
l3 (2) - for IPv4-based rule,
arpSP_permit(4) - for ARP Spoofing prevention entry,
arpSP_deny(5) - for ARP Spoofing prevention entry,
voiceVlan(6) - for Voice VLAN OUI entry.
userDefined(9) - for User Defined entry.
Note that only l2, l3 and userDefined could be set by user,
other is reserved for system to show information.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.2 |
ipv4aclProfileRuleCountThe number of rules in this profile.roobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.3 |
ipv4aclProfileMaskIndicate which field want to care in the packet.
Turn on the following bits to select the following items
Type Item BIT
L2 DST_MAC 0 (LSB)
L2 SRC_MAC 1
L2 VID 2
L2 8021P_PRIORITY 3
L2 ETHER_TYPE 4
L3 DSCP 5
L3 ICMP_TYPE 6
L3 ICMP_CODE 7
L3 IGMP_TYPE 8
L3 DST_IP 9
L3 SRC_IP 10
L3 DST_PORT 11
L3 SRC_PORT 12
L3 TCPFLAG 13
ARP-SP ARP_SENDER_MAC 14
ARP-SP ARP_SENDER_IP 15
L3 TOS 16
UDF UDF1 17
UDF UDF2 18
UDF UDF3 19
UDF UDF4 20
L3v6 TRAFFIC_CLASS 21
L3v6 DST_IPV6 22
L3v6 SRC_IPV6 23 (MSB)
The value is in Hex format.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.4 |
ipv4aclProfileDstMacAddrMaskThe ACL Profile destination MAC address mask.
If DST_MAC is turn on in aclProfileMask,
it will work with its member rule field,aclL2RuleDstMacAddr,
to caculate a range of MAC address which is really care.rwobsolete MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.5 |
ipv4aclProfileSrcMacAddrMaskThe ACL Profile source MAC address mask.
If SRC_MAC is turn on in aclProfileMask,
it will work with its member rule field,aclL2RuleSrcMacAddr,
to caculate a range of MAC address which is really care.rwobsolete MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.6 |
ipv4aclProfileIPProtocolIndicate which IP Protocol will be care in this profile.
Only profile type is l3 can set the IP protocol.
For others, this field will be none.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.7 |
ipv4aclProfileIPProtocolMaskThe ACL Profile IP protocol mask.
If aclProfileIPProtocol set to ipMask, this field will be refered.
It will work with its member rule field,aclL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.8 |
ipv4aclProfileDstIpAddrMaskThe ACL Profile destination IP address mask.
If DST_IP is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleDstIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.9 |
ipv4aclProfileSrcIpAddrMaskThe ACL Profile source IP address mask.
If SRC_IP is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleSrcIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.10 |
ipv4aclProfileDstPortMaskThe ACL Profile UDP/TCP destination port mask.
If DST_PORT is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleTcpUdpDstPort,
to caculate a range of destination port which is really care.
The value is in HEX format.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.11 |
ipv4aclProfileSrcPortMaskThe ACL Profile UDP/TCP source port mask.
If SRC_PORT is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleTcpUdpSrcPort,
to caculate a range of source port which is really care.
The value is in HEX format.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.12 |
ipv4aclProfileArpSenderMacAddrMaskThe ACL Profile Sender MAC mask.
This is only for ARP Spoofing Prevention which is System-defined ACL,
and it's not allow to modify.
The value is in HEX format.roobsolete MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.13 |
ipv4aclProfileArpSenderIpAddrMaskThe ACL Profile Sender IP mask.
This is only for ARP Spoofing Prevention which is System-defined ACL,
and it's not allow to modify.
The value is in HEX format.roobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.14 |
ipv4aclProfileUdfOffsetMapIndicate which Udf field want to care in the packet.
Turn on the following bits to select the following items
Type Item BIT
UDF Offset1 0 (LSB)
UDF Offset2 1
UDF Offset3 2
UDF Offset4 3
The value is in Hex format.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.15 |
ipv4aclUdfOffsetChunk1The value of offset Chunk.rwobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.17 |
ipv4aclUdfOffsetMask1The value of offset MAsk.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.18 |
ipv4aclUdfOffsetChunk2The value of offset Chunk.rwobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.20 |
ipv4aclUdfOffsetMask2The value of offset MAsk.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.21 |
ipv4aclUdfOffsetChunk3The value of offset Chunk.rwobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.23 |
ipv4aclUdfOffsetMask3The value of offset MAsk.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.24 |
ipv4aclUdfOffsetChunk4The value of offset Chunk.rwobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.26 |
ipv4aclUdfOffsetMask4The value of offset MAsk.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.27 |
ipv4aclProfileStatusThis object indicates the status of this entry, can only be set to
'createAndWait','active' and 'destroy'.
When the value of the entry status is 'createAndWait', it could be
set to 'active' only if the three values of aclProfileType,
aclProfileMask and ProtocolType are not conflicted.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.1.1.28 |
aclProfileTableA table to ACL profile . SEQUENCE OF AclProfileEntry .1.3.6.1.4.1.171.10.76.28.1.15.1.2 |
aclProfileEntryEach entry in this table is a ACL profile.
Index to the table is ACL profile ID. AclProfileEntry .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1 |
aclProfileNoThe ACL Profile ID. The ID 1 to 50 is user-defined ACL,
and the ID more than 50 is reserved for system-defined ACL.
The user only allow to create user-defined ACL ID.
And system-defined ACL is read only.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.1 |
aclProfileTypeThe ACL Profile type, possible value are
l2 (1) - for MAC-based rule,
l3v4 (2) - for IPv4-based rule,
l3v6 (11) - for IPv6-based rule,
arpSP_permit(4) - for ARP Spoofing prevention entry,
arpSP_deny(5) - for ARP Spoofing prevention entry,
voiceVlan(6) - for Voice VLAN OUI entry.
userDefined(9) - for User Defined entry.
Note that only l2, l3 and userDefined could be set by user,
other is reserved for system to show information.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.2 |
aclProfileRuleCountThe number of rules in this profile.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.3 |
aclProfileMaskIndicate which field want to care in the packet.
Turn on the following bits to select the following items
Type Item BIT
L2 DST_MAC 0 (LSB)
L2 SRC_MAC 1
L2 VID 2
L2 8021P_PRIORITY 3
L2 ETHER_TYPE 4
L3 DSCP 5
L3 ICMP_TYPE 6
L3 ICMP_CODE 7
L3 IGMP_TYPE 8
L3 DST_IP 9
L3 SRC_IP 10
L3 DST_PORT 11
L3 SRC_PORT 12
L3 TCPFLAG 13
ARP-SP ARP_SENDER_MAC 14
ARP-SP ARP_SENDER_IP 15
L3 TRAFFIC_CLASS 21
L3 TOS 16
UDF UDF1 17
UDF UDF2 18
UDF UDF3 19
UDF UDF4 20
L3v6 TRAFFIC_CLASS 21
L3v6 DST_IPV6 22
L3v6 SRC_IPV6 23 (MSB)
The value is in Hex format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.4 |
aclProfileDstMacAddrMaskThe ACL Profile destination MAC address mask.
If DST_MAC is turn on in aclProfileMask,
it will work with its member rule field,aclL2RuleDstMacAddr,
to caculate a range of MAC address which is really care.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.5 |
aclProfileSrcMacAddrMaskThe ACL Profile source MAC address mask.
If SRC_MAC is turn on in aclProfileMask,
it will work with its member rule field,aclL2RuleSrcMacAddr,
to caculate a range of MAC address which is really care.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.6 |
aclProfileIPProtocolIndicate which IP Protocol will be care in this profile.
Only profile type is l3 can set the IP protocol.
For others, this field will be none.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.7 |
aclProfileIPProtocolMaskThe ACL Profile IP protocol mask.
If aclProfileIPProtocol set to ipMask, this field will be refered.
It will work with its member rule field,aclL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.8 |
aclProfileDstIpAddrMaskTypeIPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.9 |
aclProfileDstIpAddrMaskThe ACL Profile destination IP address mask.
If DST_IP is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleDstIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.10 |
aclProfileSrcIpAddrMaskTypeIPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.11 |
aclProfileSrcIpAddrMaskThe ACL Profile source IP address mask.
If SRC_IP is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleSrcIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.12 |
aclProfileDstPortMaskThe ACL Profile UDP/TCP destination port mask.
If DST_PORT is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleTcpUdpDstPort,
to caculate a range of destination port which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.13 |
aclProfileSrcPortMaskThe ACL Profile UDP/TCP source port mask.
If SRC_PORT is turn on in aclProfileMask,
it will work with its member rule field,aclL3RuleTcpUdpSrcPort,
to caculate a range of source port which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.14 |
aclProfileArpSenderMacAddrMaskThe ACL Profile Sender MAC mask.
This is only for ARP Spoofing Prevention which is System-defined ACL,
and it's not allow to modify.
The value is in HEX format.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.15 |
aclProfileArpSenderIpAddrMaskThe ACL Profile Sender IP mask.
This is only for ARP Spoofing Prevention which is System-defined ACL,
and it's not allow to modify.
The value is in HEX format.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.16 |
aclProfileUdfOffsetMapIndicate which Udf field want to care in the packet.
Turn on the following bits to select the following items
Type Item BIT
UDF Offset1 0 (LSB)
UDF Offset2 1
UDF Offset3 2
UDF Offset4 3
The value is in Hex format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.17 |
aclUdfOffsetChunk1The value of offset Chunk.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.19 |
aclUdfOffsetMask1The value of offset MAsk.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.20 |
aclUdfOffsetChunk2The value of offset Chunk.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.22 |
aclUdfOffsetMask2The value of offset MAsk.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.23 |
aclUdfOffsetChunk3The value of offset Chunk.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.25 |
aclUdfOffsetMask3The value of offset MAsk.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.26 |
aclUdfOffsetChunk4The value of offset Chunk.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.28 |
aclUdfOffsetMask4The value of offset MAsk.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.29 |
aclProfileStatusThis object indicates the status of this entry, can only be set to
'createAndWait','active' and 'destroy'.
When the value of the entry status is 'createAndWait', it could be
set to 'active' only if the three values of aclProfileType,
aclProfileMask and ProtocolType are not conflicted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.1.2.1.30 |
aclL2Rule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.15.2 |
aclL2RuleTableA table to configure L2 filter rules in the system. SEQUENCE OF AclL2RuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.2.1 |
aclL2RuleEntryEach entry in this table is a L2 filter rule.
Index to the table is the L2 filter number and Profile ID. AclL2RuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1 |
aclL2AccessIDL2 Filter rule ID. 0 means auto assign.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.1 |
aclL2ProfileIDACL Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.2 |
aclL2RuleEtherTypeThe value in the Type/Len field of a frame that will
be matched to trigger this filter. The default value of
this object is '-1', which means the rule don't care this
condition.rw Integer32 (-1 | 1501..65535) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.3 |
aclL2RuleDstMacAddrDestination MAC address to be matched with the packet. By Default, the
Destination Mac Address will be zero,which means the rule don't care this
condition.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.4 |
aclL2RuleSrcMacAddrSource MAC address to be matched with the packet. By Default, the Source
Mac Address will be zero, which means the rule don't care this condition..
addressrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.5 |
aclL2RuleVlanIdVlan Id to be filtered. In case of Provider bridges, This Vlan Id will
be treated as customer Vlan Id. By Default, the value will be '-1',
which means the rule don't care this condition.rw Integer32 (-1..4094) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.6 |
aclL2Rule1pPriority802.1p priority to be matched with the packet. By Default, the value
will be '-1', which means the rule don't care this condition.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.7 |
aclL2RuleDstMacAddrMaskThe MAC address Mask work for Destination MAC address.
This field is read-only and copy from it's Profile setting.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.8 |
aclL2RuleSrcMacAddrMaskThe MAC address Mask work for Source MAC address.
This field is read-only and copy from it's Profile setting.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.9 |
aclL2RuleActionSpecifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be forwarded according
to the forwarding rules.
If the action is 'drop', the packet will be discarded.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.11 |
aclL2RuleRateLimitRate limit for matched packet.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.12 |
aclL2RuleReplaceDSCPReplace DSCP for matched packet.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.13 |
aclL2RuleReplace1PReplace DSCP for matched packet.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.14 |
aclL2RuleReplaceQueueACL L2 Rule Replace Queue.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.15 |
aclL2RuleFilterTimeRangeACL L2 Filter Time Rangerw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.16 |
aclL2RuleVlanIdMaskVlan Id to be filtered. In case of Provider bridges, This Vlan Id will
be treated as customer Vlan Id. By Default, the value will be '-1',
which means the rule don't care this condition.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.17 |
aclL2RuleInPortListSpecifies the complete set of ports over which this filter is applied
for packets ingress at ports in this list.rw PortList .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.51 |
aclL2RuleInVlanListSpecifies the complete set of Vlan over which this filter is applied
for packets ingress at vlan . Notice : Only support one VLAN.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.52 |
aclL2RuleStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.2.1.1.99 |
aclL3Rule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.15.3 |
aclL3RuleTableA table to configure L3 filter rules in the system. SEQUENCE OF AclL3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.3.1 |
aclL3RuleEntryEach entry in this table is a L3 filter rule.
Index to the table is L3 filter number and Profile ID. AclL3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1 |
aclL3RuleAccessIDL3 Filter rule ID. 0 means auto assign.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.1 |
aclL3RuleProfileNoThe Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.2 |
aclL3RuleProtocolThe type of protocol to be checked against the packet.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.3 |
aclL3RuleProtocolMaskThe IP protocol mask.
This field is read-only and copy from it's Profile setting.
It will work with the other field,aclL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.4 |
aclL3RuleICMPMessageTypeThe message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action set in aclL3RuleAction.
The default value is '-1',which means the rule don't care this
condition.
Some ICMP message types are:
echoReply(0),
destinationUnreachable(3),
sourceQuench(4),
redirect(5),
echoRequest(8),
timeExceeded(11),
parameterProblem(12),
timestampRequest(13),
timestampReply(14),
informationRequest(15),
informationReply(16),
addressMaskRequest(17),
addressMaskReply (18),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.5 |
aclL3RuleICMPMessageCodeThe message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action set in aclL3RuleAction.
The default value is '-1', which means the rule don't care this
condition.
Some ICMP message codes are :
networkUnreachable(0),
hostUnreachable(1),
protocolUnreachable(2),
portUnreachable(3),
fragmentNeed(4),
sourceRouteFail(5),
destNetworkUnknown(6),
destHostUnknown(7),
srcHostIsolated(8),
destNetworkAdminProhibited(9),
destHostAdminProhibited(10),
networkUnreachableTOS(11),
hostUnreachableTOS(12),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.6 |
aclL3RuleDstIpAddrDestination IP address to be matched with the packet.
The default value will be zero, which means the rule
don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.7 |
aclL3RuleSrcIpAddrSource IP address to be matched with the packet.
The default value will be zero, which means the
rule don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.8 |
aclL3RuleDstIpAddrMaskThe IP subnet mask for Destination IP address.
This field is read-only and copy from it's Profile setting.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.9 |
aclL3RuleSrcIpAddrMaskThe IP subnet mask for Source IP address.
This field is read-only and copy from it's Profile setting.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.10 |
aclL3RuleTcpUdpDstPortThe TCP / UDP destination port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.11 |
aclL3RuleTcpUdpSrcPortThe TCP / UDP source port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.12 |
aclL3RuleTcpUdpDstPortMaskThe TCP / UDP Destination port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.13 |
aclL3RuleTcpUdpSrcPortMaskThe TCP / UDP Source port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.14 |
aclL3RuleTcpAckBitThe TCP ACK bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.15 |
aclL3RuleTcpRstBitThe TCP RST bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.16 |
aclL3RuleTcpUrgBitThe TCP Urg bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.17 |
aclL3RuleTcpPshBitThe TCP Psh bit to be checked against the packet. The default
value is 'dont_care'(-1). which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.18 |
aclL3RuleTcpSynBitThe TCP Syn bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.19 |
aclL3RuleTcpFinBitThe TCP Fin bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.20 |
aclL3RuleDscpThe IP Dscp value to be checked against the packet.
A default value is '-1', which means the rule don't
care this condition.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.21 |
aclL3RuleTosThe IP Dscp value to be checked against the packet.
A default value is '-1', which means the rule don't
care this condition.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.22 |
aclL3RuleIgmpTypeThe IGMP Type to be checked against the packet.A default value is '-1',
which means the rule don't care this condition.rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.23 |
aclL3RuleActionSpecifies the action to be taken on the packet if the filter
rule matches.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.25 |
aclL3RuleRateLimitRate limit for matched packet.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.26 |
aclL3RuleReplaceDSCPReplaceDSCP for matched packet.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.27 |
aclL3RuleReplace1PReplaceDSCP for matched packet.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.28 |
aclL3RuleReplaceQueueAcl L3 Rule Replace Queue.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.29 |
aclL3RuleFilterTimeRangeACL L3 Filter Time Rangerw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.30 |
aclL3RulePortListSpecifies the complete set of ports over which if the packet arrives
this filter rule will be applicable.rw PortList .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.51 |
aclL3RuleVlanListSpecifies the complete set of vlan over which if the packet arrives
this filter rule will be applicable. Notice : only support one vlan.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.52 |
aclL3RuleStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.3.1.1.99 |
aclv6L3RuleTableA table to configure L3 filter rules in the system. SEQUENCE OF Aclv6L3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.3.2 |
aclv6L3RuleEntryEach entry in this table is a L3 filter rule.
Index to the table is L3 filter number and Profile ID. Aclv6L3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1 |
aclv6L3RuleAccessIDL3 Filter rule ID. 0 means auto assign.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.1 |
aclv6L3RuleProfileNoThe Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.2 |
aclv6L3RuleProtocolThe type of protocol to be checked against the packet.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.3 |
aclv6L3RuleProtocolMaskThe IP protocol mask.
This field is read-only and copy from it's Profile setting.
It will work with the other field,aclL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.4 |
aclv6L3RuleICMPMessageTypeThe message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action set in aclL3RuleAction.
The default value is '-1',which means the rule don't care this
condition.
Some ICMP message types are:
echoReply(0),
destinationUnreachable(3),
sourceQuench(4),
redirect(5),
echoRequest(8),
timeExceeded(11),
parameterProblem(12),
timestampRequest(13),
timestampReply(14),
informationRequest(15),
informationReply(16),
addressMaskRequest(17),
addressMaskReply (18),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.5 |
aclv6L3RuleICMPMessageCodeThe message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action set in aclL3RuleAction.
The default value is '-1', which means the rule don't care this
condition.
Some ICMP message codes are :
networkUnreachable(0),
hostUnreachable(1),
protocolUnreachable(2),
portUnreachable(3),
fragmentNeed(4),
sourceRouteFail(5),
destNetworkUnknown(6),
destHostUnknown(7),
srcHostIsolated(8),
destNetworkAdminProhibited(9),
destHostAdminProhibited(10),
networkUnreachableTOS(11),
hostUnreachableTOS(12),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.6 |
aclv6L3RuleDstIpAddrDestination IP address to be matched with the packet.
The default value will be zero, which means the rule
don't care this condition.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.7 |
aclv6L3RuleSrcIpAddrSource IP address to be matched with the packet.
The default value will be zero, which means the
rule don't care this condition.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.8 |
aclv6L3RuleDstIpAddrMaskThe IP subnet mask for Destination IP address.
This field is read-only and copy from it's Profile setting.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.9 |
aclv6L3RuleSrcIpAddrMaskThe IP subnet mask for Source IP address.
This field is read-only and copy from it's Profile setting.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.10 |
aclv6L3RuleTcpUdpDstPortThe TCP / UDP destination port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.11 |
aclv6L3RuleTcpUdpSrcPortThe TCP / UDP source port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.12 |
aclv6L3RuleTcpUdpDstPortMaskThe TCP / UDP Destination port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.13 |
aclv6L3RuleTcpUdpSrcPortMaskThe TCP / UDP Source port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.14 |
aclv6L3RuleTcpAckBitThe TCP ACK bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.15 |
aclv6L3RuleTcpRstBitThe TCP RST bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.16 |
aclv6L3RuleTcpUrgBitThe TCP Urg bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.17 |
aclv6L3RuleTcpPshBitThe TCP Psh bit to be checked against the packet. The default
value is 'dont_care'(-1). which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.18 |
aclv6L3RuleTcpSynBitThe TCP Syn bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.19 |
aclv6L3RuleTcpFinBitThe TCP Fin bit to be checked against the packet. The default
value is 'dont_care'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.20 |
aclv6L3RuleTrafficClassThe IP Dscp value to be checked against the packet.
A default value is '-1', which means the rule don't
care this condition.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.21 |
aclv6L3RuleActionSpecifies the action to be taken on the packet if the filter
rule matches.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.24 |
aclv6L3RuleRateLimitRate limit for matched packet.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.25 |
aclv6L3RuleReplaceDSCPReplace DSCP for matched packet.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.26 |
aclv6L3RuleReplace1PReplace DSCP for matched packet.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.27 |
aclv6L3RuleReplaceQueueAcl IPV6 L3 Rule Replace Queue.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.28 |
aclv6L3RuleFilterTimeRangeACL IPV6 L3 Filter Time Rangerw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.29 |
aclv6L3RulePortListSpecifies the complete set of ports over which if the packet arrives
this filter rule will be applicable.rw PortList .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.51 |
aclv6L3RuleVlanListSpecifies the complete set of vlan over which if the packet arrives
this filter rule will be applicable. Notice : only support one vlan.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.52 |
aclv6L3RuleStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.3.2.1.99 |
aclPacketRule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.15.4 |
aclPacketRuleTableA table to configure Packet Content filter rules in the system. SEQUENCE OF AclPacketRuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.4.1 |
aclPacketRuleEntryEach entry in this table is a Packet filter rule.
Index to the table is the Packet filter number and Profile ID. AclPacketRuleEntry .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1 |
aclPacketAccessIDPacket Filter rule ID. 0 means auto assign.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.1 |
aclPacketProfileIDACL Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.2 |
aclPacketRuleOffsetValue1The filter value of Offset 1.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.3 |
aclPacketRuleOffsetValue2The filter value of Offset 2.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.4 |
aclPacketRuleOffsetValue3The filter value of Offset 3.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.5 |
aclPacketRuleOffsetValue4The filter value of Offset 4.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.6 |
aclPacketRuleActionSpecifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be forwarded according
to the forwarding rules.
If the action is 'drop', the packet will be discarded.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.8 |
aclPacketRuleRateLimitRate limit for matched packet.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.9 |
aclPacketRuleReplaceDSCPReplace DSCP for matched packet.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.10 |
aclPacketRuleReplace1PReplace 1p for matched packet.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.11 |
aclPacketRuleReplaceQueueAcl Rule Replace Queue.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.12 |
aclPacketRuleFilterTimeRangeAcl Filter Time Rangerw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.13 |
aclPacketRuleOffsetValue1MaskThe filter Mask of Offset 1.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.14 |
aclPacketRuleOffsetValue2MaskThe filter Mask of Offset 2.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.15 |
aclPacketRuleOffsetValue3MaskThe filter Mask of Offset 3.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.16 |
aclPacketRuleOffsetValue4MaskThe filter Mask of Offset 4.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.17 |
aclPacketRuleInPortListSpecifies the complete set of ports over which this filter is applied
for packets ingress at ports in this list.rw PortList .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.51 |
aclPacketRuleInVlanListSpecifies the complete set of vlan over which this filter is applied
for packets ingress at vlan. Notice : Only support one vlan.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.52 |
aclPacketRuleStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.4.1.1.99 |
aclFlowMeterRule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.15.10 |
aclFlowMeterTableA table to configure L2 filter rules in the system. SEQUENCE OF AclFlowMeterEntry .1.3.6.1.4.1.171.10.76.28.1.15.10.1 |
aclFlowMeterEntryEach entry in this table is a L2 filter rule.
Index to the table is the L2 filter number and Profile ID. AclFlowMeterEntry .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1 |
aclFlowMeterProfileIDACL Profile ID which this flow meter join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1.1 |
aclFlowMeterAccessIDACL Access ID which this flow meter join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1.2 |
aclFlowMeterRateThe rate limiter of meter.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1.3 |
aclFlowMeterBurstSizeThe burst size of meter.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1.4 |
aclFlowMeterReplaceDscpReplace DSCP for matched out-band packets when aclFlowMeterAction is replace DSCP.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1.5 |
aclFlowMeterActionSpecifies the action to be taken on the out-band packet if the filter
rule matches.
If the action is 'drop', the packet will be discarded.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1.6 |
aclFlowMeterStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.15.10.1.1.99 |
companySyslog OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.16 |
syslogSettingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.16.1 |
syslogEnableThis object is for enabling or disabling syslog alert features in
the system and the syslog will save to flash or send to remote
syslog server.
System Logs record and manage events, as well as report errors and
informational messages.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.1.1 |
syslogSaveModeThis object is for choosing the method to save syslog into flash.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.1.2 |
syslogSaveMinutesWhen savemode is time interval, it's used to set the interval minutes of
system save syslog to flash.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.16.1.3 |
ipv4syslogServerGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.16.2 |
ipv4syslogServTableThe table of syslog remote server. SEQUENCE OF Ipv4SyslogServEntry .1.3.6.1.4.1.171.10.76.28.1.16.2.1 |
ipv4syslogServEntryThe list of syslog remote server entry. Ipv4SyslogServEntry .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1 |
ipv4syslogServIndexThe index of syslog remote server.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1.1 |
ipv4syslogServAddrThe IP Address of syslog remote server.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1.2 |
ipv4syslogServSeveritySpecifies the log level option to be set for a specific server.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1.3 |
ipv4syslogServFacilityThe Syslog standard facilities.
The facility to be used when sending Syslog messages to this server.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1.4 |
ipv4syslogServUDPportThe value is for setting UDP Port.rw INTEGER (514 | 6000..65535) .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1.5 |
ipv4syslogServSrvStatusThe status for this server. If enable, system will send message to
this server.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1.6 |
ipv4syslogServSrvRowStatusRow status of this server entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.16.2.1.1.7 |
syslogServerGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.16.3 |
syslogServTableThe table of syslog remote server. SEQUENCE OF SyslogServEntry .1.3.6.1.4.1.171.10.76.28.1.16.3.1 |
syslogServEntryThe list of syslog remote server entry. SyslogServEntry .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1 |
syslogServIndexThe index of syslog remote server.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.1 |
syslogServAddrTypeSpecifies the Address type of server.Address type shall be ipv4 or ipv6.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.2 |
syslogServAddrSpecifies the ServerIP to which the syslog shall be forwarded.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.3 |
syslogServInterfaceNameSpecifies the interface name when the syslogServInterfaceName is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.4 |
syslogServSeveritySpecifies the log level option to be set for a specific server.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.5 |
syslogServFacilityThe Syslog standard facilities.
The facility to be used when sending Syslog messages to this server.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.6 |
syslogServUDPportThe value is for setting UDP Port.rw INTEGER (514 | 6000..65535) .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.7 |
syslogServSrvStatusThe status for this server. If enable, system will send message to
this server.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.8 |
syslogServSrvRowStatusRow status of this server entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.16.3.1.1.9 |
companyLBD OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.17 |
sysLBDStateEnableEnable/Disable Loopback detection function.
The Loopback Detection function is used to detect the loop created
by a specific port while Spanning Tree Protocol (STP) is not
enabled in the network, especially when the down links are hubs
or unmanaged switchs.The Switch will automatically shutdown the
port and sends a log to the administrator.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.17.1 |
sysLBDModeLoopback detection function mode.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.17.2 |
sysLBDIntervalSet a Loop detection Interval between 1 and 32767 seconds.
The default is 2 seconds.
This time interval to be used at counting time seconds to
resend the CTP packet automatically.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.17.3 |
sysLBDRecoverTimeThis time interval to be used at counting time seconds to
recover the disabled port automatically.
The Loop Detection Recover Time can be set at 0 seconds,
or 60 to 1000000 seconds.
Entering 0 will disable the Loop Detection Recover Time.
The default is 60 seconds.rw Integer32 (0 | 60..1000000) .1.3.6.1.4.1.171.10.76.28.1.17.4 |
sysLBDCtrlTableA table to control Loopback detection features either for
the entire switch or for each interface in the switch. SEQUENCE OF SysLBDCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.17.5 |
sysLBDCtrlEntryAn entry appears in this table for each interface
in the system. SysLBDCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.17.5.1 |
sysLBDCtrlIndexThe interface index of the port for which the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.17.5.1.1 |
sysLBDPortStatusProvides control to per port enable or disable the loopback detection
function. Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.17.5.1.2 |
sysLBDPortLoopStatusThe loop status for this port.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.17.5.1.3 |
sysLBDVlanLoopTableA table to display Loopback detection features by vlan
mode . SEQUENCE OF SysLBDVlanLoopEntry .1.3.6.1.4.1.171.10.76.28.1.17.6 |
sysLBDVlanLoopEntryAn entry appears in this table for each interface
in the system. SysLBDVlanLoopEntry .1.3.6.1.4.1.171.10.76.28.1.17.6.1 |
sysLBDVlanLoopIndexDisplay port lists loop status by vlan.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.17.6.1.1 |
sysLBDVlanLoopPortsDisplay port lists loop status by vlan.ro PortList .1.3.6.1.4.1.171.10.76.28.1.17.6.1.2 |
companyMirror OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.18 |
sysMirrorStatusEnable/Disable Port Mirroring function.
Default is disabled.
Port Mirroring is a method of monitoring network traffic that
forwards a copy of each incoming and/or outgoing packet from one
port of the Switch to another port where the packet can be studied.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.18.1 |
sysMirrorTargetPortSpecifies the port to which the mirrored traffic in the system
is to be copied.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.18.2 |
sysMirrorCtrlIngressMirroringProvides control to enable or disable mirroring of ingress
traffic over this interface to the mirrored-to port.rw PortList .1.3.6.1.4.1.171.10.76.28.1.18.3 |
sysMirrorCtrlEgressMirroringProvides control to enable or disable mirroring of egress
traffic over this interface to the mirrored-to port.rw PortList .1.3.6.1.4.1.171.10.76.28.1.18.4 |
companyStaticMcast OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.19 |
staticMcastTableA list of the Static MACs SEQUENCE OF StaticMcastEntry .1.3.6.1.4.1.171.10.76.28.1.19.1 |
staticMcastEntryA Static MAC entry containing the mac and forwarding port. StaticMcastEntry .1.3.6.1.4.1.171.10.76.28.1.19.1.1 |
staticMcastVlanIDThe VLAN ID of the static MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.19.1.1.1 |
staticMcastMacThe MAC address associated of the static MAC entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.19.1.1.2 |
staticMcastEgressPortsThe set of ports to which frames received from a
specific port and destined for a specific Multicast or
Broadcast MAC address must be forwarded, regardless of
any dynamic information e.g. from GMRP. A port may not
be added in this set if it is already a member of the
set of ports in dot1qStaticMulticastForbiddenEgressPorts.
The default value of this object is a string of ones of
appropriate length.ro PortList .1.3.6.1.4.1.171.10.76.28.1.19.1.1.3 |
staticMcastIpAddrStatic Multicast IP Address.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.19.1.1.4 |
staticMcastStatusThe status of an entry in the Static Mcast Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.19.1.1.5 |
companySNTPSetting OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.20 |
ipv4sysSNTPTimeSecondsThis object is for setting the system time in seconds
from Epoch (00:00:00 UTC, January 1, 2009). Notice :
input value must larger than 1230768000 (00:00:00 UTC,
January 1, 2009) and smaller than 2145916799 (23:59:59
UTC, December 31, 2037).rwobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.20.1 |
ipv4sysSNTPFirstServerSNTP First Server's IP Addressrwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.20.2 |
ipv4sysSNTPSecondServerSNTP Second Server's IP Addressrwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.20.3 |
ipv4sysSNTPPollIntervalSNTP Poll Interval In Seconds (30-99999)rwobsolete Integer32 .1.3.6.1.4.1.171.10.76.28.1.20.4 |
ipv4sysSNTPStateEnable/Disable SNTP function in the system.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.5 |
ipv4sysSNTPDSTOffsetThis object is for Daylight Saving Time Offset In (30/60/90/120) Minutes.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.6 |
ipv4sysSNTPGMTMinutesSpecifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.7 |
ipv4sysSNTPDSTStartMonThe start month of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.8 |
ipv4sysSNTPDSTStartDayThe start day of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.9 |
ipv4sysSNTPDSTStartHourThe start hour of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.10 |
ipv4sysSNTPDSTStartMinThe start minute of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.11 |
ipv4sysSNTPDSTEndMonThe end month of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.12 |
ipv4sysSNTPDSTEndDayThe end day of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.13 |
ipv4sysSNTPDSTEndHourThe end hour of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.14 |
ipv4sysSNTPDSTEndMinThe end minute of Daylight Saving Time.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.15 |
ipv4sysSNTPDSTStateThis object is for Annual(1) or Disabled(2) DST state in the system.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.16 |
sysSNTPServerTable OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.20.17 |
sysSNTPTimeSecondsThis object is for setting the system time in seconds
from Epoch (00:00:00 UTC, January 1, 2009). Notice :
input value must larger than 1230768000 (00:00:00 UTC,
January 1, 2009) and smaller than 2145916799 (23:59:59
UTC, December 31, 2037).rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.20.17.1 |
sysSNTPFirstServerSNTP First Server's IPv6 Addressrw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.20.17.2 |
sysSNTPFirstTypeSNTP First Server's IPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.3 |
sysSNTPFirstInterfaceNameSpecifies the interface name when the sysSNTPFirstServer is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.20.17.4 |
sysSNTPSecondServerSNTP Second Server's IPv6 Addressrw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.20.17.5 |
sysSNTPSecondTypeSNTP First Server's IPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.6 |
sysSNTPSecondInterfaceNameSpecifies the interface name when the sysSNTPSecondServer is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.20.17.7 |
sysSNTPPollIntervalSNTP Poll Interval In Seconds (30-99999)rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.20.17.8 |
sysSNTPStateEnable/Disable SNTP function in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.9 |
sysSNTPDSTOffsetThis object is for Daylight Saving Time Offset
In (30/60/90/120) Minutes.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.10 |
sysSNTPGMTMinutesSpecifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.11 |
sysSNTPDSTStartMonThe start month of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.12 |
sysSNTPDSTStartDayThe start day of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.13 |
sysSNTPDSTStartHourThe start hour of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.14 |
sysSNTPDSTStartMinThe start minute of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.15 |
sysSNTPDSTEndMonThe end month of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.16 |
sysSNTPDSTEndDayThe end day of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.17 |
sysSNTPDSTEndHourThe end hour of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.18 |
sysSNTPDSTEndMinThe end minute of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.19 |
sysSNTPDSTStateThis object is for Enabled(1) or Disabled(2) DST state in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.20 |
sysSNTPDSTMethodThis object is for Annual(1) or Repeating(2) DST method in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.30 |
sysSNTPDSTRepeatStartMonThe start month of Daylight Saving Time in Repeating mode.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.31 |
sysSNTPDSTRepeatStartWeekThe start week of Daylight Saving Time in Repeating mode.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.32 |
sysSNTPDSTRepeatStartWeekDayThe start weekday of Daylight Saving Time in Repeating mode.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.33 |
sysSNTPDSTRepeatStartHourThe start hour of Daylight Saving Time in Repeating mode..rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.34 |
sysSNTPDSTRepeatStartMinThe start minute of Daylight Saving Time in Repeating mode.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.35 |
sysSNTPDSTRepeatEndMonThe end month of Daylight Saving Time in Repeating mode.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.36 |
sysSNTPDSTRepeatEndWeekThe end week of Daylight Saving Time in Repeating mode.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.37 |
sysSNTPDSTRepeatEndWeekDayThe end weekday of Daylight Saving Time in Repeating mode.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.20.17.38 |
sysSNTPDSTRepeatEndHourThe end hour of Daylight Saving Time in Repeating mode..rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.39 |
sysSNTPDSTRepeatEndMinThe end minute of Daylight Saving Time in Repeating mode.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.20.17.40 |
companyRMON OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22 |
rmonGlobalStateThis object is for enabling or disabling RMON function.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.22.1 |
rmonStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22.2 |
rmonStatsTableA list of Ethernet statistics entries. SEQUENCE OF RmonStatsEntry .1.3.6.1.4.1.171.10.76.28.1.22.2.1 |
rmonStatsEntryA collection of statistics kept for a particular
Ethernet interface. As an example, an instance of the
etherStatsPkts object might be named etherStatsPkts.1 RmonStatsEntry .1.3.6.1.4.1.171.10.76.28.1.22.2.1.1 |
rmonStatsIndexThe value of this object uniquely identifies this
etherStats entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.2.1.1.1 |
rmonStatsDataSourceThis object identifies the source of the data that
this etherStats entry is configured to analyze. This
source can be any ethernet interface on this device.
In order to identify a particular interface, this object
shall identify the instance of the ifIndex object,
defined in RFC 2233 [17], for the desired interface.
For example, if an entry were to receive data from
interface #1, this object would be set to ifIndex.1.
The statistics in this group reflect all packets
on the local network segment attached to the identified
interface.
An agent may or may not be able to tell if fundamental
changes to the media of the interface have occurred and
necessitate an invalidation of this entry. For example, a
hot-pluggable ethernet card could be pulled out and replaced
by a token-ring card. In such a case, if the agent has such
knowledge of the change, it is recommended that it
invalidate this entry.
This object may not be modified if the associated
etherStatsStatus object is equal to valid(1).rw OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22.2.1.1.2 |
rmonStatsOwnerThe entity that configured this entry and is therefore
using the resources assigned to it.rw OwnerString .1.3.6.1.4.1.171.10.76.28.1.22.2.1.1.3 |
rmonStatsStatusThe status of this etherStats entry.rw RmonStatus .1.3.6.1.4.1.171.10.76.28.1.22.2.1.1.4 |
rmonHistory OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22.3 |
rmonHistoryTableA list of history control entries. SEQUENCE OF RmonHistoryEntry .1.3.6.1.4.1.171.10.76.28.1.22.3.1 |
rmonHistoryEntryA list of parameters that set up a periodic sampling of
statistics. As an example, an instance of the
historyControlInterval object might be named
historyControlInterval.2 RmonHistoryEntry .1.3.6.1.4.1.171.10.76.28.1.22.3.1.1 |
rmonHistoryIndexAn index that uniquely identifies an entry in the
historyControl table. Each such entry defines a
set of samples at a particular interval for an
interface on the device.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.3.1.1.1 |
rmonHistoryDataSourceThis object identifies the source of the data for
which historical data was collected and
placed in a media-specific table on behalf of this
historyControlEntry. This source can be any
interface on this device. In order to identify
a particular interface, this object shall identify
the instance of the ifIndex object, defined
in RFC 2233 [17], for the desired interface.
For example, if an entry were to receive data from
interface #1, this object would be set to ifIndex.1.
The statistics in this group reflect all packets
on the local network segment attached to the identified
interface.
An agent may or may not be able to tell if fundamental
changes to the media of the interface have occurred and
necessitate an invalidation of this entry. For example, a
hot-pluggable ethernet card could be pulled out and replaced
by a token-ring card. In such a case, if the agent has such
knowledge of the change, it is recommended that it
invalidate this entry.
This object may not be modified if the associated
historyControlStatus object is equal to valid(1).rw OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22.3.1.1.2 |
rmonHistoryBucketsRequestedThe requested number of discrete time intervals
over which data is to be saved in the part of the
media-specific table associated with this
historyControlEntry.
When this object is created or modified, the probe
should set historyControlBucketsGranted as closely to
this object as is possible for the particular probe
implementation and available resources.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.3.1.1.3 |
rmonHistoryIntervalThe interval in seconds over which the data is
sampled for each bucket in the part of the
media-specific table associated with this
historyControlEntry. This interval can
be set to any number of seconds between 1 and
3600 (1 hour).
Because the counters in a bucket may overflow at their
maximum value with no indication, a prudent manager will
take into account the possibility of overflow in any of
the associated counters. It is important to consider the
minimum time in which any counter could overflow on a
particular media type and set the historyControlInterval
object to a value less than this interval. This is
typically most important for the 'octets' counter in any
media-specific table. For example, on an Ethernet
network, the etherHistoryOctets counter could overflow
in about one hour at the Ethernet's maximum
utilization.
This object may not be modified if the associated
historyControlStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.3.1.1.4 |
rmonHistoryOwnerThe entity that configured this entry and is therefore
using the resources assigned to it.rw OwnerString .1.3.6.1.4.1.171.10.76.28.1.22.3.1.1.5 |
rmonHistoryStatusThe status of this historyControl entry.
Each instance of the media-specific table associated
with this historyControlEntry will be deleted by the agent
if this historyControlEntry is not equal to valid(1).rw RmonStatus .1.3.6.1.4.1.171.10.76.28.1.22.3.1.1.6 |
rmonAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22.4 |
rmonAlarmTableA list of alarm entries. SEQUENCE OF RmonAlarmEntry .1.3.6.1.4.1.171.10.76.28.1.22.4.1 |
rmonAlarmEntryA list of parameters that set up a periodic checking
for alarm conditions. For example, an instance of the
alarmValue object might be named alarmValue.8 RmonAlarmEntry .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1 |
rmonAlarmIndexAn index that uniquely identifies an entry in the
alarm table. Each such entry defines a
diagnostic sample at a particular interval
for an object on the device.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.1 |
rmonAlarmIntervalThe interval in seconds over which the data is
sampled and compared with the rising and falling
thresholds. When setting this variable, care
should be taken in the case of deltaValue
sampling - the interval should be set short enough
that the sampled variable is very unlikely to
increase or decrease by more than 2^31 - 1 during
a single sampling interval.
This object may not be modified if the associated
alarmStatus object is equal to valid(1).rw Integer32 UNITS "Seconds" .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.2 |
rmonAlarmVariableThe object identifier of the particular variable to be
sampled. Only variables that resolve to an ASN.1 primitive
type of INTEGER (INTEGER, Integer32, Counter32, Counter64,
Gauge, or TimeTicks) may be sampled.
Because SNMP access control is articulated entirely
in terms of the contents of MIB views, no access
control mechanism exists that can restrict the value of
this object to identify only those objects that exist
in a particular MIB view. Because there is thus no
acceptable means of restricting the read access that
could be obtained through the alarm mechanism, the
probe must only grant write access to this object in
those views that have read access to all objects on
the probe.
During a set operation, if the supplied variable name is
not available in the selected MIB view, a badValue error
must be returned. If at any time the variable name of
an established alarmEntry is no longer available in the
selected MIB view, the probe must change the status of
this alarmEntry to invalid(4).
This object may not be modified if the associated
alarmStatus object is equal to valid(1).rw OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.3 |
rmonAlarmSampleTypeThe method of sampling the selected variable and
calculating the value to be compared against the
thresholds. If the value of this object is
absoluteValue(1), the value of the selected variable
will be compared directly with the thresholds at the
end of the sampling interval. If the value of this
object is deltaValue(2), the value of the selected
variable at the last sample will be subtracted from
the current value, and the difference compared with
the thresholds.
This object may not be modified if the associated
alarmStatus object is equal to valid(1).rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.4 |
rmonAlarmRisingThresholdA threshold for the sampled statistic. When the current
sampled value is greater than or equal to this threshold,
and the value at the last sampling interval was less than
this threshold, a single event will be generated.
A single event will also be generated if the first
sample after this entry becomes valid is greater than or
equal to this threshold and the associated
alarmStartupAlarm is equal to risingAlarm(1) or
risingOrFallingAlarm(3).
After a rising event is generated, another such event
will not be generated until the sampled value
falls below this threshold and reaches the
alarmFallingThreshold.
This object may not be modified if the associated
alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.5 |
rmonAlarmFallingThresholdA threshold for the sampled statistic. When the current
sampled value is less than or equal to this threshold,
and the value at the last sampling interval was greater than
this threshold, a single event will be generated.
A single event will also be generated if the first
sample after this entry becomes valid is less than or
equal to this threshold and the associated
alarmStartupAlarm is equal to fallingAlarm(2) or
risingOrFallingAlarm(3).
After a falling event is generated, another such event
will not be generated until the sampled value
rises above this threshold and reaches the
alarmRisingThreshold.
This object may not be modified if the associated
alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.6 |
rmonAlarmRisingEventIndexThe index of the eventEntry that is
used when a rising threshold is crossed. The
eventEntry identified by a particular value of
this index is the same as identified by the same value
of the eventIndex object. If there is no
corresponding entry in the eventTable, then
no association exists. In particular, if this value
is zero, no associated event will be generated, as
zero is not a valid event index.
This object may not be modified if the associated
alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.7 |
rmonAlarmFallingEventIndexThe index of the eventEntry that is
used when a falling threshold is crossed. The
eventEntry identified by a particular value of
this index is the same as identified by the same value
of the eventIndex object. If there is no
corresponding entry in the eventTable, then
no association exists. In particular, if this value
is zero, no associated event will be generated, as
zero is not a valid event index.
This object may not be modified if the associated
alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.8 |
rmonAlarmOwnerThe entity that configured this entry and is therefore
using the resources assigned to it.rw OwnerString .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.9 |
rmonAlarmStatusThe status of this alarm entry.rw RmonStatus .1.3.6.1.4.1.171.10.76.28.1.22.4.1.1.10 |
rmonEvent OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.22.5 |
rmonEventTableA list of events to be generated. SEQUENCE OF RmonEventEntry .1.3.6.1.4.1.171.10.76.28.1.22.5.1 |
rmonEventEntryA set of parameters that describe an event to be generated
when certain conditions are met. As an example, an instance
of the eventLastTimeSent object might be named
eventLastTimeSent.6 RmonEventEntry .1.3.6.1.4.1.171.10.76.28.1.22.5.1.1 |
rmonEventIndexAn index that uniquely identifies an entry in the
event table. Each such entry defines one event that
is to be generated when the appropriate conditions
occur.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.22.5.1.1.1 |
rmonEventDescriptionA comment describing this event entry.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.22.5.1.1.2 |
rmonEventTypeThe type of notification that the probe will make
about this event. In the case of log, an entry is
made in the log table for each event. In the case of
snmp-trap, an SNMP trap is sent to one or more
management stations.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.22.5.1.1.3 |
rmonEventCommunityIf an SNMP trap is to be sent, it will be sent to
the SNMP community specified by this octet string.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.22.5.1.1.4 |
rmonEventOwnerThe entity that configured this entry and is therefore
using the resources assigned to it.
If this object contains a string starting with 'monitor'
and has associated entries in the log table, all connected
management stations should retrieve those log entries,
as they may have significance to all management stations
connected to this devicerw OwnerString .1.3.6.1.4.1.171.10.76.28.1.22.5.1.1.5 |
rmonEventStatusThe status of this event entry.
If this object is not equal to valid(1), all associated
log entries shall be deleted by the agent.rw RmonStatus .1.3.6.1.4.1.171.10.76.28.1.22.5.1.1.6 |
companyAuthGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.23 |
swAuthenCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.23.1 |
swAuthStatusEnable/Disable Static 802.1x.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.1.1 |
swAuthModeThis object indicates the authentication mode of the device.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.1.2 |
authProtocolThe authentication method used to authenticate users.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.1.3 |
swAuthCtrlPktFwdModeWhen 802.1x disable, this item can decided eap packet be forward or drop.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.1.4 |
swAuthPortAccessCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.23.2 |
swAuthPortAccessControlTableA table that contains the configuration objects for the
Authenticator PAE associated with each port.
An entry appears in this table for each port that may
authenticate access to itself. SEQUENCE OF SwAuthPortAccessControlEntry .1.3.6.1.4.1.171.10.76.28.1.23.2.1 |
swAuthPortAccessControlEntryThe configuration information for an Authenticator Port. SwAuthPortAccessControlEntry .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1 |
swAuthAuthConfigPortNumberA unique value for each port that correlates to port index.
Its value ranges between 1 and the value of port number.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.1 |
swAuthAuthQuietPeriodThe value, in seconds, of the quietPeriod constant
currently in use by the Authenticator PAE state
machine.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.2 |
swAuthAuthSuppTimeoutThe value, in seconds, of the suppTimeout constant
currently in use by the Backend Authentication state
machine.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.3 |
swAuthAuthServerTimeoutThe value, in seconds, of the serverTimeout constant
currently in use by the Backend Authentication state
machine.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.4 |
swAuthAuthMaxReqThe value of the maxReq constant currently in use by
the Backend Authentication state machine.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.5 |
swAuthAuthTxPeriodThe value, in seconds, of the txPeriod constant
currently in use by the Authenticator PAE state
machine.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.6 |
swAuthAuthReAuthPeriodThe value, in seconds, of the reAuthPeriod constant
currently in use by the Reauthentication Timer state
machine.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.7 |
swAuthAuthReAuthenticationThe enable/disable control used by the Reauthentication
Timer state machine (8.5.5.1).rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.8 |
swAuthAuthConfigPortControlThe current value of the controlled Port
control parameter for the Port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.9 |
swAuthAuthCapabilityThe current value of the controlled Port
control parameter for the Port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.10 |
swAuthAuthDirectionThe current value of the controlled Port
control parameter for the Port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.23.2.1.1.11 |
swAuthUser OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.23.3 |
swAuthUserTableA table that contains the configuration objects for the
Authenticator PAE associated with each port.
An entry appears in this table for each port that may
authenticate access to itself. SEQUENCE OF SwAuthUserEntry .1.3.6.1.4.1.171.10.76.28.1.23.3.1 |
swAuthUserEntryThe configuration information for an Authenticator Port. SwAuthUserEntry .1.3.6.1.4.1.171.10.76.28.1.23.3.1.1 |
swAuthUserNameThe unique index value of a row in this table.
This object is used to set 802.1X Local user name,
The following characters are allowed to input:
semicolon, question mark, space, and double quotation mark.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.23.3.1.1.1 |
swAuthUserPasswordThis object is used to set 802.1X Local user Password,
The following characters are allowed to input:
semicolon, question mark, space, and double quotation mark.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.23.3.1.1.2 |
swAuthUserStatusThe status of this conceptual row in the swAuthUserTable.
An entry in this table is not qualified for activation
until instances of all corresponding columns have been
initialized, either through default values, or through
Set operations. The swAuthUserName objects must be
explicitly set.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.23.3.1.1.3 |
swAuthRadiusServer OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.23.4 |
iPv4swAuthRadiusServerTableA table that contains the configuration objects for the
Authenticator PAE associated with each port.
An entry appears in this table for each port that may
authenticate access to itself.obsolete SEQUENCE OF IPv4SwAuthRadiusServerEntry .1.3.6.1.4.1.171.10.76.28.1.23.4.1 |
iPv4swAuthRadiusServerEntryThe configuration information for an Authenticator Port.obsolete IPv4SwAuthRadiusServerEntry .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1 |
iPv4swAuthRadiusServerIndexA unique value for Authentication RADIUS Server index.
Its value ranges between 1 and 3.roobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.1 |
iPv4swAuthRadiusServerAddressThe IP address of the RADIUS server
referred to in this table entry.rwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.2 |
iPv4swAuthRadiusServerAuthenticationPortThe value is for setting UDP Port.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.3 |
iPv4swAuthRadiusServerAccountingPortThe value is for setting UDP Port.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.4 |
iPv4swAuthRadiusServerTimeoutThe value is for setting UDP Port.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.5 |
iPv4swAuthRadiusServerRetransmitThe value is for setting UDP Port.rwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.6 |
iPv4swAuthRadiusServerKeyThis object is used to set 802.1X Radius Server Key,
The following characters are allowed to input:
semicolon, question mark, space, and double quotation mark.rwobsolete DisplayString .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.7 |
iPv4swAuthRadiusServerStatusThe status of this conceptual row in the
swAuthRadiusServerTable.
An entry in this table is not qualified for activation
until instances of all corresponding columns have been
initialized, either through default values, or through
Set operations. The swAuthRadiusServerIndex objects
must be explicitly set.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.23.4.1.1.8 |
swAuthRadiusServerTableA table that contains the configuration objects for the
Authenticator PAE associated with each port.
An entry appears in this table for each port that may
authenticate access to itself. SEQUENCE OF SwAuthRadiusServerEntry .1.3.6.1.4.1.171.10.76.28.1.23.4.2 |
swAuthRadiusServerEntryThe configuration information for an Authenticator Port. SwAuthRadiusServerEntry .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1 |
swAuthRadiusServerIndexA unique value for Authentication RADIUS Server index.
Its value ranges between 1 and 3.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.1 |
swAuthRadiusIPTypeThe IP address of the RADIUS server IP type
referred to in this table entry.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.2 |
swAuthRadiusServerAddressThe IP address of the RADIUS server
referred to in this table entry.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.3 |
swAuthRadiusServerInterfaceNameSpecifies the interface name when the swAuthRadiusServerAddress is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.4 |
swAuthRadiusServerAuthenticationPortThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.5 |
swAuthRadiusServerAccountingPortThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.6 |
swAuthRadiusServerTimeoutThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.7 |
swAuthRadiusServerRetransmitThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.8 |
swAuthRadiusServerKeyThis object is used to set 802.1X Radius Server Key,
The following characters are allowed to input:
semicolon, question mark, space, and double quotation mark.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.9 |
swAuthRadiusServerStatusThe status of this conceptual row in the
swAuthRadiusServerTable.
An entry in this table is not qualified for activation
until instances of all corresponding columns have been
initialized, either through default values, or through
Set operations. The swAuthRadiusServerIndex objects
must be explicitly set.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.23.4.2.1.10 |
companyGuestVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.24 |
guestVlanNameThe VLAN name of guest VLAN.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.24.1 |
guestVlanPortThis object indicates the guest VLAN port members of this device.rw PortList .1.3.6.1.4.1.171.10.76.28.1.24.2 |
guestVlanDelStateUsed to delete the guest VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.24.3 |
companyMacNotify OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.25 |
macNotifyStateThis object can enabled or disabled MAC Notification.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.25.1 |
macNotifyIntervalThis object indicates the time interval in second for trigger the MAC notify message.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.25.2 |
macNotifyHistorySizeThis object indicates the history size of variation MAC in address table. The default value is 1 .rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.25.3 |
macNotifyCtrlTableA table to control Loopback detection features either for
the entire switch or for each interface in the switch. SEQUENCE OF MacNotifyCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.25.4 |
macNotifyCtrlEntryAn entry appears in this table for each interface
in the system. MacNotifyCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.25.4.1 |
macNotifyCtrlIndexThe interface index of the port for which the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.25.4.1.1 |
macNotifyPortStatusProvides control to per port enable or disable the loopback detection
function. Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.25.4.1.2 |
macNotifyInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.25.5 |
macNotifyInfoDiscriptionThis object indicates the information for the device MAC address changes. And the detailed information include:
Operation Code + MAC address + Box ID + Port Number + Zero...
Operation Code: 1, 2 and 3
1 means learned a new MAC address
2 means deleted an old MAC address.
3 means station movement.
Box ID: The switch box ID, for standalone device, it always 1.
Port Number: The port number learned or deleted for the box.
Zero: Used to separate each message (Operate Code + MAC address + Box ID + Port Number).ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.25.5.1 |
companyISMVLAN OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.27 |
igmpMulticastVlanStatusEnable/Disable IGMP Multicast Vlan function.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.27.1 |
igmpMulticastVlanTableInformation about the IGMP snooping multicast VLAN table. SEQUENCE OF IgmpMulticastVlanEntry .1.3.6.1.4.1.171.10.76.28.1.27.2 |
igmpMulticastVlanEntryThe entry of igmpMulticastVlanTable. IgmpMulticastVlanEntry .1.3.6.1.4.1.171.10.76.28.1.27.2.1 |
igmpMulticastVlanidThis object indicates the VLAN ID of the IGMP snooping multicast
VLAN entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.27.2.1.1 |
igmpMulticastVlanNameThis object indicates the VLAN name of the IGMP snooping multicast
VLAN entry.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.27.2.1.2 |
igmpMulticastVlanSourcePortThis object indicates the port list of the source ports of the IGMP
snooping multicast VLAN. The source ports will be set as tag ports
of the VLAN entry and the IGMP control messages received from the
member ports will be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.2.1.3 |
igmpMulticastVlanMemberPortThis object indicates the port list of the member ports of the IGMP
snooping multicast VLAN. The source ports will be set as untagged ports
of the VLAN entry and the IGMP control messages received from the
member ports will be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.2.1.4 |
igmpMulticastVlanTagMemberPortThis object indicates the port list of the tag member ports of the IGMP
snooping multicast VLAN.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.2.1.5 |
igmpMulticastVlanUntaggedSourcePortThis object indicates the port list of the untag source ports of the IGMP
snooping multicast VLAN.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.2.1.6 |
igmpMulticastVlanStateThis object can be used to enable or disable the IGMP snooping multicast VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.27.2.1.7 |
igmpMulticastVlanReplaceSourceIpThe replacement source IP of this multicast VLAN.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.27.2.1.8 |
igmpMulticastVlanRemapPriorityThe remap priority of this multicast VLAN.rw INTEGER (-1..7) .1.3.6.1.4.1.171.10.76.28.1.27.2.1.9 |
igmpMulticastVlanReplacePriorityThe replacement priority of this multicast VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.27.2.1.10 |
igmpMulticastVlanRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.27.2.1.11 |
igmpMulticastVlanGroupTableThe table containing the IGMP snooping multicast VLAN group information SEQUENCE OF IgmpMulticastVlanGroupEntry .1.3.6.1.4.1.171.10.76.28.1.27.3 |
igmpMulticastVlanGroupEntryInformation about the current IGMP snooping multicast VLAN group. IgmpMulticastVlanGroupEntry .1.3.6.1.4.1.171.10.76.28.1.27.3.1 |
igmpMulticastVlanGroupVidThis object indicates the VID of the IGMP snooping multicast VLAN group.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.27.3.1.1 |
igmpMulticastVlanGroupFromIpSpecifies the multicast address list for this VLAN.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.27.3.1.2 |
igmpMulticastVlanGroupToIpSpecifies the multicast address list for this VLAN.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.27.3.1.3 |
igmpMulticastVlanGroupStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.27.3.1.4 |
multicastVlanTableInformation about the IGMP/MLD snooping multicast VLAN table. SEQUENCE OF MulticastVlanEntry .1.3.6.1.4.1.171.10.76.28.1.27.4 |
multicastVlanEntryThe entry of multicastVlanTable. MulticastVlanEntry .1.3.6.1.4.1.171.10.76.28.1.27.4.1 |
multicastVlanidThis object indicates the VLAN ID of the IGMP/MLD snooping
multicast VLAN entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.27.4.1.1 |
multicastVlanNameThis object indicates the VLAN name of the IGMP/MLD snooping
multicast VLAN entry.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.27.4.1.2 |
multicastVlanSourcePortThis object indicates the port list of the source ports of the
IGMP/MLD snooping multicast VLAN. The source ports will be set as
tag ports of the VLAN entry and the IGMP control messages received
from themember ports will be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.4.1.3 |
multicastVlanMemberPortThis object indicates the port list of the member ports of the
IGMP/MLD snooping multicast VLAN. The source ports will be set as
untagged ports of the VLAN entry and the IGMP control messages
received from themember ports will be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.4.1.4 |
multicastVlanTagMemberPortThis object indicates the port list of the tag member ports of the
IGMP/MLD snooping multicast VLAN.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.4.1.5 |
multicastVlanUntaggedSourcePortThis object indicates the port list of the untag source ports of the
IGMP/MLD snooping multicast VLAN.rw PortList .1.3.6.1.4.1.171.10.76.28.1.27.4.1.6 |
multicastVlanStateThis object can be used to enable or disable the IGMP/MLD snooping
multicast VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.27.4.1.7 |
multicastVlanIgmpReplaceSourceIpThe replacement source IP of this IGMP snooping multicast VLAN.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.27.4.1.8 |
multicastVlanMldReplaceSourceIpThe replacement source IP of this MLD snooping multicast VLAN.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.27.4.1.9 |
multicastVlanRemapPriorityThe remap priority of this multicast VLAN.rw INTEGER (-1..7) .1.3.6.1.4.1.171.10.76.28.1.27.4.1.10 |
multicastVlanReplacePriorityThe replacement priority of this multicast VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.27.4.1.11 |
multicastVlanRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.27.4.1.12 |
multicastVlanGroupTableThe table containing the IGMP/MLD snooping multicast VLAN group information SEQUENCE OF MulticastVlanGroupEntry .1.3.6.1.4.1.171.10.76.28.1.27.5 |
multicastVlanGroupEntryThe entry of multicastVlanGroupTable. MulticastVlanGroupEntry .1.3.6.1.4.1.171.10.76.28.1.27.5.1 |
multicastVlanGroupVidThis object indicates the VID of the IGMP/MLD snooping multicast VLAN group.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.27.5.1.1 |
multicastVlanGroupIpTypeType of specifies the multicast address list for this VLAN.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.27.5.1.2 |
multicastVlanGroupFromIpSpecifies the multicast address list for this VLAN.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.27.5.1.3 |
multicastVlanGroupToIpSpecifies the multicast address list for this VLAN.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.27.5.1.4 |
multicastVlanGroupStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.27.5.1.5 |
companyDHCPRelay OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.28 |
dhcpBOOTPRelayControl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.28.1 |
dhcpBOOTPRelayStateThis object indicates DHCP relay function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.28.1.1 |
dhcpBOOTPRelayHopCountThis object indicates the maximum number of router hops that the BOOTP packets can cross.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.28.1.2 |
dhcpBOOTPRelayTimeThresholdThis object indicates the minimum time in seconds within which the switch must relay the DHCP request.
If this time is exceeded, the switch will drop the DHCP packet.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.28.1.3 |
dhcpBOOTPRelayEnablePortlistThis object indicates DHCP relay function is enabled or disabled by portlist.rw PortList .1.3.6.1.4.1.171.10.76.28.1.28.1.4 |
dhcpRelayVlanTableThis table indicates the IP address as a destination to forward (relay) DHCP packets to. SEQUENCE OF DHCPRelayVlanSettings .1.3.6.1.4.1.171.10.76.28.1.28.1.5 |
dhcpRelayVlanTableEntryA list of information indicates the IP address as a destination to forward (relay) DHCP packets to. DHCPRelayVlanSettings .1.3.6.1.4.1.171.10.76.28.1.28.1.5.1 |
dhcpRelayVlanSettingsVLANIDThis object displays the current VLAN ID of the device.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.28.1.5.1.1 |
dhcpRelayVlanSettingsStateThis object indicates DHCP relay function of VLAN is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.28.1.5.1.2 |
dhcpBOOTPRelayManagement OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.28.2 |
dhcpBOOTPRelayInterfaceSettingsTableThis table indicates the IP address as a destination to forward (relay) DHCP packets to. SEQUENCE OF DHCPBOOTPRelayInterfaceSettings .1.3.6.1.4.1.171.10.76.28.1.28.2.1 |
dhcpBOOTPRelayInterfaceSettingsEntryA list of information indicates the IP address as a destination to forward (relay) DHCP packets to. DHCPBOOTPRelayInterfaceSettings .1.3.6.1.4.1.171.10.76.28.1.28.2.1.1 |
dhcpBOOTPRelayInterfaceThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.28.2.1.1.1 |
dhcpBOOTPRelayServerIPThis object indicates the DHCP server IP address.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.28.2.1.1.2 |
dhcpBOOTPRelayInterfaceSettingsRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.28.2.1.1.3 |
dhcpBOOTPRelayManagementOption82 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.28.2.2 |
dhcpBOOTPRelayOption82StateThis object indicates DHCP relay option 82 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.28.2.2.1 |
dhcpBOOTPRelayOption82CheckStateThis object indicates DHCP relay option 82 Check function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.28.2.2.2 |
dhcpBOOTPRelayOption82PolicyThis object indicates DHCP relay option 82 policy.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.28.2.2.3 |
dhcpBOOTPRelayOption82RemoteIDTypeThis object indicates the type of remote ID.
If the type is default, the remote ID will be the MAC address of the device, otherwise,
the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.28.2.2.4 |
dhcpBOOTPRelayOption82RemoteIDThis object displays the current remote ID of the device.
If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device,
and this object cannot be modified.
If swDHCPRelayOption82RemoteIDType is set to user-defined or user-defined-hex, a new value can be written to this object.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.28.2.2.5 |
dhcpBOOTPRelayOption82CircuitIDTypeThis object indicates the type of remote ID.
If the type is default, the circuit ID will be blank, otherwise,
the circuit ID can be defined by writing to the dhcpBOOTPRelayOption82CircuitID object.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.28.2.2.7 |
dhcpBOOTPRelayOption82CircuitIDThis object displays the current remote ID of the device.
If dhcpBOOTPRelayOption82CircuitIDType is set to default, the value will be the MAC address of the device,
and this object cannot be modified.
If dhcpBOOTPRelayOption82CircuitIDType is set to user-defined or user-defined-hex, a new value can be written to this object.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.28.2.2.8 |
companyDHCPLocalRelay OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.29 |
dhcpLocalRelayGlobalStateThis object indicates DHCP local relay function of VLAN is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.29.1 |
dhcpLocalRelayTableThis table indicates the IP address as a destination to forward (local relay) DHCP packets to. SEQUENCE OF DHCPLocalRelaySettings .1.3.6.1.4.1.171.10.76.28.1.29.2 |
dhcpLocalRelayTableEntryA list of information indicates the IP address as a destination to forward (local relay) DHCP packets to. DHCPLocalRelaySettings .1.3.6.1.4.1.171.10.76.28.1.29.2.1 |
dhcpLocalRelaySettingsVLANIDThis object displays the current VLAN ID of the device.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.29.2.1.1 |
dhcpLocalRelaySettingsStateThis object indicates DHCP local relay function of VLAN is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.29.2.1.2 |
dhcpLocalRelayEnablePortlistThis object indicates DHCP local relay function is enabled or disabled by portlist.rw PortList .1.3.6.1.4.1.171.10.76.28.1.29.3 |
companyGreenSetting OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.31 |
dlinkGreenLEDShutoff OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.31.1 |
dlinkGreenLEDShutoffPortListProvides control to disable LED port.rw PortList .1.3.6.1.4.1.171.10.76.28.1.31.1.1 |
dlinkGreenLEDShutoffStateEnable/Disable Green disable LED function.
Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.31.1.2 |
dlinkGreenLEDShutoffTimeProfile1The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.31.1.3 |
dlinkGreenLEDShutoffTimeProfile2The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.31.1.4 |
dlinkGreenPortShutoff OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.31.2 |
dlinkGreenPortShutoffPortListProvides control to disable LED port.rw PortList .1.3.6.1.4.1.171.10.76.28.1.31.2.1 |
dlinkGreenPortShutoffStateEnable/Disable Green disable LED function.
Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.31.2.2 |
dlinkGreenPortShutoffTimeProfile1The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.31.2.3 |
dlinkGreenPortShutoffTimeProfile2The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.31.2.4 |
dlinkGreenSystemHibernation OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.31.4 |
dlinkGreenSystemHibernationStateEnable/Disable Green disable LED function.
Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.31.4.1 |
dlinkGreenSystemHibernationTimeProfile1The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.31.4.2 |
dlinkGreenSystemHibernationTimeProfile2The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.31.4.3 |
dlinkPowerSavLinkStatusDetectStateEnable/Disable Power Saving Link Status Detection.
Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.31.6 |
companyLLDPSetting OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32 |
dlinklldpStateThis object is used for enabling or disabling LLDP in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.32.1 |
dlinklldpMsgHoldMultiplierThe time-to-live value expressed as a multiple of the
lldpMessageTxInterval object.The actual time-to-live value
used in LLDP frames, transmitted on behalf of this LLDP agent,
can be expressed by the following formula: TTL = min(65535,
(lldpMessageTxInterval * lldpMessageTxHoldMultiplier))rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.32.2 |
dlinklldpMsgTxIntervalThis object is used for LLDP packet update frequency.
The timer in units of seconds.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.32.3 |
dlinklldpReinitDelayThis object is used for LLDP Reinitialization Delay.
The timer in units of seconds.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.32.4 |
dlinklldpTxDelayThe lldpTxDelay indicates the delay (in units
of seconds) between successive LLDP frame transmissions
initiated by value/status changes in the LLDP local systems
MIB. The recommended value for the lldpTxDelay is set by the
following formula:
1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval).rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.32.5 |
dlinklldpConfigManAddrPortsTxEnableA set of ports that are identified by a PortList, in which
each port is represented as a bit. The corresponding local
system management address instance will be transmitted on the
member ports of the lldpManAddrPortsTxEnable.
The default value for lldpConfigManAddrPortsTxEnable object
is empty binary string, which means no ports are specified
for advertising indicated management address instance.rw PortList .1.3.6.1.4.1.171.10.76.28.1.32.6 |
lldpPortConfigTableThe table that controls LLDP frame transmission on individual
ports. SEQUENCE OF LldpPortConfigEntry .1.3.6.1.4.1.171.10.76.28.1.32.11 |
lldpPortConfigEntryLLDP configuration information for a particular port.
This configuration parameter controls the transmission and
the reception of LLDP frames on those ports whose rows are
created in this table. LldpPortConfigEntry .1.3.6.1.4.1.171.10.76.28.1.32.11.1 |
lldpPortConfigPortNumThe index value used to identify the port component
(contained in the local chassis with the LLDP agent)
associated with this entry.
The value of this object is used as a port index to the
lldpPortConfigTable. LldpPortNumber .1.3.6.1.4.1.171.10.76.28.1.32.11.1.1 |
lldpPortConfigAdminStatusThe administratively desired status of the local LLDP agent.
If the associated lldpPortConfigAdminStatus object has a
value of 'txOnly(1)', then LLDP agent will transmit LLDP
frames on this port and it will not store any information
about the remote systems connected.
If the associated lldpPortConfigAdminStatus object has a
value of 'rxOnly(2)', then the LLDP agent will receive,
but it will not transmit LLDP frames on this port.
If the associated lldpPortConfigAdminStatus object has a
value of 'txAndRx(3)', then the LLDP agent will transmit
and receive LLDP frames on this port.
If the associated lldpPortConfigAdminStatus object has a
value of 'disabled(4)', then LLDP agent will not transmit or
receive LLDP frames on this port. If there is remote systems
information which is received on this port and stored in
other tables, before the port's lldpPortConfigAdminStatus
becomes disabled, then the information will naturally age out.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.32.11.1.2 |
lldpPortConfigNotificationEnableThe lldpPortConfigNotificationEnable controls, on a per
port basis, whether or not notifications from the agent
are enabled. The value true(1) means that notifications are
enabled; the value false(2) means that they are not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.11.1.3 |
lldpPortConfigTLVsTxEnableThe lldpPortConfigTLVsTxEnable, defined as a bitmap,
includes the basic set of LLDP TLVs whose transmission is
allowed on the local LLDP agent by the network management.
Each bit in the bitmap corresponds to a TLV type associated
with a specific optional TLV.
It should be noted that the organizationally-specific TLVs
are excluded from the lldpTLVsTxEnable bitmap.
LLDP Organization Specific Information Extension MIBs should
have similar configuration object to control transmission
of their organizationally defined TLVs.
The bit 'portDesc(0)' indicates that LLDP agent should
transmit 'Port Description TLV'.
The bit 'sysName(1)' indicates that LLDP agent should transmit
'System Name TLV'.
The bit 'sysDesc(2)' indicates that LLDP agent should transmit
'System Description TLV'.
The bit 'sysCap(3)' indicates that LLDP agent should transmit
'System Capabilities TLV'.
There is no bit reserved for the management address TLV type
since transmission of management address TLVs are controlled
by another object, lldpConfigManAddrTable.
The default value for lldpPortConfigTLVsTxEnable object is
empty set, which means no enumerated values are set.
The value of this object must be restored from non-volatile
storage after a re-initialization of the management system.rw Bits .1.3.6.1.4.1.171.10.76.28.1.32.11.1.4 |
lldpXdot3Objects OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.12 |
lldpXdot3Config OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.12.1 |
lldpXdot3PortConfigTableA table that controls selection of LLDP TLVs to be transmitted
on individual ports. SEQUENCE OF LldpXdot3PortConfigEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.1.1 |
lldpXdot3PortConfigEntryLLDP configuration information that controls the
transmission of IEEE 802.3 organizationally defined TLVs on
LLDP transmission capable ports.
This configuration object augments the lldpPortConfigEntry of
the LLDP-MIB, therefore it is only present along with the port
configuration defined by the associated lldpPortConfigEntry
entry.
Each active lldpXdot3PortConfigEntry must be from non-volatile
storage (along with the corresponding lldpPortConfigEntry)
after a re-initialization of the management system. LldpXdot3PortConfigEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.1.1.1 |
lldpXdot3PortConfigTLVsTxEnableThe lldpXdot3PortConfigTLVsTxEnable, defined as a bitmap,
includes the IEEE 802.3 organizationally defined set of LLDP
TLVs whose transmission is allowed on the local LLDP agent by
the network management. Each bit in the bitmap corresponds
to an IEEE 802.3 subtype associated with a specific IEEE
802.3 optional TLV. The bit 0 is not used since there is
no corresponding subtype.
The bit 'macPhyConfigStatus(0)' indicates that LLDP agent
should transmit 'MAC/PHY configuration/status TLV'.
The bit 'powerViaMDI(1)' indicates that LLDP agent should
transmit 'Power via MDI TLV'.
The bit 'linkAggregation(2)' indicates that LLDP agent should
transmit 'Link Aggregation TLV'.
The bit 'maxFrameSize(3)' indicates that LLDP agent should
transmit 'Maximum-frame-size TLV'.
The default value for lldpXdot3PortConfigTLVsTxEnable object
is an empty set, which means no enumerated values are set.
The value of this object must be restored from non-volatile
storage after a re-initialization of the management system.rw Bits .1.3.6.1.4.1.171.10.76.28.1.32.12.1.1.1.1 |
lldpXdot3LocalData OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.12.2 |
lldpXdot3LocPortTableThis table contains one row per port of Ethernet port
information (as a part of the LLDP 802.3 organizational
extension) on the local system known to this agent. SEQUENCE OF LldpXdot3LocPortEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.1 |
lldpXdot3LocPortEntryInformation about a particular port component. LldpXdot3LocPortEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.1.1 |
lldpXdot3LocPortAutoNegSupportedThe truth value used to indicate whether the given port
(associated with the local system) supports Auto-negotiation.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.1.1.1 |
lldpXdot3LocPortAutoNegEnabledThe truth value used to indicate whether port
Auto-negotiation is enabled on the given port associated
with the local system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.1.1.2 |
lldpXdot3LocPortAutoNegAdvertisedCapThis object contains the value (bitmap) of the
ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC
3636) which is associated with the given port on the
local system.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.32.12.2.1.1.3 |
lldpXdot3LocPortOperMauTypeAn integer value that indicates the operational MAU type
of the given port on the local system.
This object contains the integer value derived from the
list position of the corresponding dot3MauType as listed
in IETF RFC 3636 (or subsequent revisions) and is equal
to the last number in the respective dot3MauType OID.
For example, if the ifMauType object is dot3MauType1000BaseTHD
which corresponds to {dot3MauType 29}, the numerical value of
this field will be 29. For MAU types not listed in RFC 3636
(or subsequent revisions), the value of this field shall be
set to zero.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.32.12.2.1.1.4 |
lldpXdot3LocPowerTableThis table contains one row per port of power ethernet
information (as a part of the LLDP 802.3 organizational
extension) on the local system known to this agent. SEQUENCE OF LldpXdot3LocPowerEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2 |
lldpXdot3LocPowerEntryInformation about a particular port component. LldpXdot3LocPowerEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2.1 |
lldpXdot3LocPowerPortClassThe value that identifies the port Class of the given port
associated with the local system.ro LldpPowerPortClass .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2.1.1 |
lldpXdot3LocPowerMDISupportedThe truth value used to indicate whether the MDI power is
supported on the given port associated with the local system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2.1.2 |
lldpXdot3LocPowerMDIEnabledThe truth value used to identify whether MDI power is
enabled on the given port associated with the local system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2.1.3 |
lldpXdot3LocPowerPairControlableThe truth value is derived from the value of
pethPsePortPowerPairsControlAbility object (defined in IETF
RFC 3621) and is used to indicate whether the pair selection
can be controlled on the given port associated with the
local system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2.1.4 |
lldpXdot3LocPowerPairsThis object contains the value of the pethPsePortPowerPairs
object (defined in IETF RFC 3621) which is associated with
the given port on the local system.ro Integer32(1|2) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2.1.5 |
lldpXdot3LocPowerClassThis object contains the value of the
pethPsePortPowerClassifications object (defined in IETF
RFC 3621) which is associated with the given port on the
local system.ro Integer32(1|2|3|4|5) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.2.1.6 |
lldpXdot3LocLinkAggTableThis table contains one row per port of link aggregation
information (as a part of the LLDP 802.3 organizational
extension) on the local system known to this agent. SEQUENCE OF LldpXdot3LocLinkAggEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.3 |
lldpXdot3LocLinkAggEntryLink Aggregation information about a particular port
component. LldpXdot3LocLinkAggEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.3.1 |
lldpXdot3LocLinkAggStatusThe bitmap value contains the link aggregation capabilities
and the current aggregation status of the link.ro LldpLinkAggStatusMap .1.3.6.1.4.1.171.10.76.28.1.32.12.2.3.1.1 |
lldpXdot3LocLinkAggPortIdThis object contains the IEEE 802.3 aggregated port
identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1),
derived from the ifNumber of the ifIndex for the port
component in link aggregation.
If the port is not in link aggregation state and/or it
does not support link aggregation, this value should be set
to zero.ro Integer32(0|1..2147483647) .1.3.6.1.4.1.171.10.76.28.1.32.12.2.3.1.2 |
lldpXdot3LocMaxFrameSizeTableThis table contains one row per port of maximum frame
size information (as a part of the LLDP 802.3 organizational
extension) on the local system known to this agent. SEQUENCE OF LldpXdot3LocMaxFrameSizeEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.4 |
lldpXdot3LocMaxFrameSizeEntryMaximum Frame Size information about a particular port
component. LldpXdot3LocMaxFrameSizeEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.2.4.1 |
lldpXdot3LocMaxFrameSizeAn integer value indicating the maximum supported frame
size in octets on the given port of the local system.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.32.12.2.4.1.1 |
lldpXdot3RemoteData OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.12.3 |
lldpXdot3RemPortTableThis table contains Ethernet port information (as a part
of the LLDP 802.3 organizational extension) of the remote
system. SEQUENCE OF LldpXdot3RemPortEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.1 |
lldpXdot3RemPortEntryInformation about a particular physical network connection. LldpXdot3RemPortEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.1.1 |
lldpXdot3RemPortAutoNegSupportedThe truth value used to indicate whether the given port
(associated with remote system) supports Auto-negotiation.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.1.1.1 |
lldpXdot3RemPortAutoNegEnabledThe truth value used to indicate whether port
Auto-negotiation is enabled on the given port associated
with the remote system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.1.1.2 |
lldpXdot3RemPortAutoNegAdvertisedCapThis object contains the value (bitmap) of the
ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC
3636) which is associated with the given port on the
remote system.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.32.12.3.1.1.3 |
lldpXdot3RemPortOperMauTypeAn integer value that indicates the operational MAU type
of the sending device.
This object contains the integer value derived from the
list position of the corresponding dot3MauType as listed in
in IETF RFC 3636 (or subsequent revisions) and is equal
to the last number in the respective dot3MauType OID.
For example, if the ifMauType object is dot3MauType1000BaseTHD
which corresponds to {dot3MauType 29}, the numerical value of
this field will be 29. For MAU types not listed in RFC 3636
(or subsequent revisions), the value of this field shall be
set to zero.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.32.12.3.1.1.4 |
lldpXdot3RemPowerTableThis table contains Ethernet power information (as a part
of the LLDP 802.3 organizational extension) of the remote
system. SEQUENCE OF LldpXdot3RemPowerEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2 |
lldpXdot3RemPowerEntryInformation about a particular physical network connection. LldpXdot3RemPowerEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2.1 |
lldpXdot3RemPowerPortClassThe value that identifies the port Class of the given port
associated with the remote system.ro LldpPowerPortClass .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2.1.1 |
lldpXdot3RemPowerMDISupportedThe truth value used to indicate whether the MDI power
is supported on the given port associated with the remote
system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2.1.2 |
lldpXdot3RemPowerMDIEnabledThe truth value used to identify whether MDI power is
enabled on the given port associated with the remote system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2.1.3 |
lldpXdot3RemPowerPairControlableThe truth value is derived from the value of
pethPsePortPowerPairsControlAbility object (defined in IETF
RFC 3621) and is used to indicate whether the pair selection
can be controlled on the given port associated with the
remote system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2.1.4 |
lldpXdot3RemPowerPairsThis object contains the value of the pethPsePortPowerPairs
object (defined in IETF RFC 3621) which is associated with
the given port on the remote system.ro Integer32(1|2) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2.1.5 |
lldpXdot3RemPowerClassThis object contains the value of the
pethPsePortPowerClassifications object (defined in IETF
RFC 3621) which is associated with the given port on the
remote system.ro Integer32(1|2|3|4|5) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.2.1.6 |
lldpXdot3RemLinkAggTableThis table contains port link aggregation information
(as a part of the LLDP 802.3 organizational extension)
of the remote system. SEQUENCE OF LldpXdot3RemLinkAggEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.3 |
lldpXdot3RemLinkAggEntryLink Aggregation information about remote system's port
component. LldpXdot3RemLinkAggEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.3.1 |
lldpXdot3RemLinkAggStatusThe bitmap value contains the link aggregation capabilities
and the current aggregation status of the link.ro LldpLinkAggStatusMap .1.3.6.1.4.1.171.10.76.28.1.32.12.3.3.1.1 |
lldpXdot3RemLinkAggPortIdThis object contains the IEEE 802.3 aggregated port
identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1),
derived from the ifNumber of the ifIndex for the port
component associated with the remote system.
If the remote port is not in link aggregation state and/or
it does not support link aggregation, this value should be
zero.ro Integer32(0|1..2147483647) .1.3.6.1.4.1.171.10.76.28.1.32.12.3.3.1.2 |
lldpXdot3RemMaxFrameSizeTableThis table contains one row per port of maximum frame
size information (as a part of the LLDP 802.3 organizational
extension) of the remote system. SEQUENCE OF LldpXdot3RemMaxFrameSizeEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.4 |
lldpXdot3RemMaxFrameSizeEntryMaximum Frame Size information about a particular port
component. LldpXdot3RemMaxFrameSizeEntry .1.3.6.1.4.1.171.10.76.28.1.32.12.3.4.1 |
lldpXdot3RemMaxFrameSizeAn integer value indicating the maximum supported frame
size in octets on the port component associated with the
remote system.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.32.12.3.4.1.1 |
lldpXdot1Objects OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.13 |
lldpXdot1Config OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.13.1 |
lldpXdot1ConfigPortVlanTableA table that controls selection of LLDP Port VLAN-ID TLVs
to be transmitted on individual ports. SEQUENCE OF LldpXdot1ConfigPortVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.1 |
lldpXdot1ConfigPortVlanEntryLLDP configuration information that controls the
transmission of IEEE 802.1 organizationally defined Port
VLAN-ID TLV on LLDP transmission capable ports.
This configuration object augments the lldpPortConfigEntry of
the LLDP-MIB, therefore it is only present along with the port
configuration defined by the associated lldpPortConfigEntry
entry.
Each active lldpConfigEntry must be restored from non-volatile
storage (along with the corresponding lldpPortConfigEntry)
after a re-initialization of the management system. LldpXdot1ConfigPortVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.1.1 |
lldpXdot1ConfigPortVlanTxEnableThe lldpXdot1ConfigPortVlanTxEnable, which is defined as
a truth value and configured by the network management,
determines whether the IEEE 802.1 organizationally defined
port VLAN TLV transmission is allowed on a given LLDP
transmission capable port.
The value of this object must be restored from non-volatile
storage after a re-initialization of the management system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.1.1.1.1 |
lldpXdot1ConfigVlanNameTableThe table that controls selection of LLDP VLAN name TLV
instances to be transmitted on individual ports. SEQUENCE OF LldpXdot1ConfigVlanNameEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.2 |
lldpXdot1ConfigVlanNameEntryLLDP configuration information that specifies the set of
ports (represented as a PortList) on which the Local System
VLAN name instance will be transmitted.
This configuration object augments the lldpLocVlanEntry,
therefore it is only present along with the VLAN Name instance
contained in the associated lldpLocVlanNameEntry entry.
Each active lldpXdot1ConfigVlanNameEntry must be restored
from non-volatile storage (along with the corresponding
lldpXdot1LocVlanNameEntry) after a re-initialization of the
management system. LldpXdot1ConfigVlanNameEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.2.1 |
lldpXdot1ConfigVlanNameTxEnableThe boolean value that indicates whether the corresponding
Local System VLAN name instance will be transmitted on the
port defined by the given lldpXdot1LocVlanNameEntry.
The value of this object must be restored from non-volatile
storage after a re-initialization of the management system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.1.2.1.1 |
lldpXdot1ConfigProtoVlanTableThe table that controls selection of LLDP Port and Protocol
VLAN ID TLV instances to be transmitted on individual ports. SEQUENCE OF LldpXdot1ConfigProtoVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.3 |
lldpXdot1ConfigProtoVlanEntryLLDP configuration information that specifies the set of
ports (represented as a PortList) on which the Local System
Protocol VLAN instance will be transmitted.
This configuration object augments the lldpXdot1LocVlanEntry,
therefore it is only present along with the Port and
Protocol VLAN ID instance contained in the associated
lldpXdot1LocVlanEntry entry.
Each active lldpXdot1ConfigProtoVlanEntry must be restored
from non-volatile storage (along with the corresponding
lldpXdot1LocProtoVlanEntry) after a re-initialization of
the management system. LldpXdot1ConfigProtoVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.3.1 |
lldpXdot1ConfigProtoVlanTxEnableThe boolean value that indicates whether the corresponding
Local System Port and Protocol VLAN instance will
be transmitted on the port defined by the given
lldpXdot1LocProtoVlanEntry.
The value of this object must be restored from non-volatile
storage after a re-initialization of the management system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.1.3.1.1 |
lldpXdot1ConfigProtocolTableThe table that controls selection of LLDP Protocol
TLV instances to be transmitted on individual ports. SEQUENCE OF LldpXdot1ConfigProtocolEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.4 |
lldpXdot1ConfigProtocolEntryLLDP configuration information that specifies the set of
ports (represented as a PortList) on which the Local System
Protocol instance will be transmitted.
This configuration object augments the lldpXdot1LocProtoEntry,
therefore it is only present along with the Protocol instance
contained in the associated lldpXdot1LocProtoEntry entry.
Each active lldpXdot1ConfigProtocolEntry must be restored
from non-volatile storage (along with the corresponding
lldpXdot1LocProtocolEntry) after a re-initialization of the
management system. LldpXdot1ConfigProtocolEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.1.4.1 |
lldpXdot1ConfigProtocolTxEnableThe boolean value that indicates whether the corresponding
Local System Protocol Identity instance will be transmitted
on the port defined by the given lldpXdot1LocProtocolEntry.
The value of this object must be restored from non-volatile
storage after a re-initialization of the management system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.1.4.1.1 |
lldpXdot1LocalData OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.13.2 |
lldpXdot1LocTableThis table contains one row per port for IEEE 802.1
organizationally defined LLDP extension on the local system
known to this agent. SEQUENCE OF LldpXdot1LocEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.1 |
lldpXdot1LocEntryInformation about IEEE 802.1 organizationally defined
LLDP extension. LldpXdot1LocEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.1.1 |
lldpXdot1LocPortVlanIdThe integer value used to identify the port's VLAN identifier
associated with the local system. A value of zero shall
be used if the system either does not know the PVID or does
not support port-based VLAN operation.ro Integer32(0|1..4094) .1.3.6.1.4.1.171.10.76.28.1.32.13.2.1.1.1 |
lldpXdot1LocProtoVlanTableThis table contains one or more rows per Port and Protocol
VLAN information about the local system. SEQUENCE OF LldpXdot1LocProtoVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.2 |
lldpXdot1LocProtoVlanEntryPort and protocol VLAN ID Information about a particular
port component. There may be multiple port and protocol VLANs,
identified by a particular lldpXdot1LocProtoVlanId, configured
on the given port. LldpXdot1LocProtoVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.2.1 |
lldpXdot1LocProtoVlanIdThe integer value used to identify the port and protocol
VLANs associated with the given port associated with the
local system. A value of zero shall be used if the system
either does not know the protocol VLAN ID (PPVID) or does
not support port and protocol VLAN operation. Integer32(0|1..4094) .1.3.6.1.4.1.171.10.76.28.1.32.13.2.2.1.1 |
lldpXdot1LocProtoVlanSupportedThe truth value used to indicate whether the given port
(associated with the local system) supports port and protocol
VLANs.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.2.2.1.2 |
lldpXdot1LocProtoVlanEnabledThe truth value used to indicate whether the port and
protocol VLANs are enabled on the given port associated with
the local system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.2.2.1.3 |
lldpXdot1LocVlanNameTableThis table contains one or more rows per IEEE 802.1Q VLAN
name information on the local system known to this agent. SEQUENCE OF LldpXdot1LocVlanNameEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.3 |
lldpXdot1LocVlanNameEntryVLAN name Information about a particular port component.
There may be multiple VLANs, identified by a particular
lldpXdot1LocVlanId, configured on the given port. LldpXdot1LocVlanNameEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.3.1 |
lldpXdot1LocVlanIdThe integer value used to identify the IEEE 802.1Q
VLAN IDs with which the given port is compatible. VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.171.10.76.28.1.32.13.2.3.1.1 |
lldpXdot1LocVlanNameThe string value used to identify VLAN name identified by the
Vlan Id associated with the given port on the local system.
This object should contain the value of the dot1QVLANStaticName
object (defined in IETF RFC 2674) identified with the given
lldpXdot1LocVlanId.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.32.13.2.3.1.2 |
lldpXdot1LocProtocolTableThis table contains one or more rows per protocol identity
information on the local system known to this agent. SEQUENCE OF LldpXdot1LocProtocolEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.4 |
lldpXdot1LocProtocolEntryInformation about particular protocols that are accessible
through the given port component.
There may be multiple protocols, identified by particular
lldpXdot1ProtocolIndex, and lldpLocPortNum. LldpXdot1LocProtocolEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.2.4.1 |
lldpXdot1LocProtocolIndexThis object represents an arbitrary local integer value used
by this agent to identify a particular protocol identity. Integer32 .1.3.6.1.4.1.171.10.76.28.1.32.13.2.4.1.1 |
lldpXdot1LocProtocolIdThe octet string value used to identify the protocols
associated with the given port of the local system.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.32.13.2.4.1.2 |
lldpXdot1RemoteData OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.32.13.3 |
lldpXdot1RemTableThis table contains one or more rows per physical network
connection known to this agent. The agent may wish to
ensure that only one lldpXdot1RemEntry is present for
each local port, or it may choose to maintain multiple
lldpXdot1RemEntries for the same local port. SEQUENCE OF LldpXdot1RemEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.1 |
lldpXdot1RemEntryInformation about a particular port component. LldpXdot1RemEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.1.1 |
lldpXdot1RemPortVlanIdThe integer value used to identify the port's VLAN identifier
associated with the remote system. if the remote system
either does not know the PVID or does not support port-based
VLAN operation, the value of lldpXdot1RemPortVlanId should
be zero.ro Integer32(0|1..4094) .1.3.6.1.4.1.171.10.76.28.1.32.13.3.1.1.1 |
lldpXdot1RemProtoVlanTableThis table contains one or more rows per Port and Protocol
VLAN information about the remote system, received on the
given port. SEQUENCE OF LldpXdot1RemProtoVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.2 |
lldpXdot1RemProtoVlanEntryPort and protocol VLAN name Information about a particular
port component. There may be multiple protocol VLANs,
identified by a particular lldpXdot1RemProtoVlanId, configured
on the remote system. LldpXdot1RemProtoVlanEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.2.1 |
lldpXdot1RemProtoVlanIdThe integer value used to identify the port and protocol
VLANs associated with the given port associated with the
remote system.
If port and protocol VLANs are not supported on the given
port associated with the remote system, or if the port is
not enabled with any port and protocol VLAN, the value of
lldpXdot1RemProtoVlanId should be zero. Integer32(0|1..4094) .1.3.6.1.4.1.171.10.76.28.1.32.13.3.2.1.1 |
lldpXdot1RemProtoVlanSupportedThe truth value used to indicate whether the given port
(associated with the remote system) is capable of supporting
port and protocol VLANs.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.3.2.1.2 |
lldpXdot1RemProtoVlanEnabledThe truth value used to indicate whether the port and
protocol VLANs are enabled on the given port associated with
the remote system.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.32.13.3.2.1.3 |
lldpXdot1RemVlanNameTableThis table contains one or more rows per IEEE 802.1Q VLAN
name information about the remote system, received on the
given port. SEQUENCE OF LldpXdot1RemVlanNameEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.3 |
lldpXdot1RemVlanNameEntryVLAN name Information about a particular port component.
There may be multiple VLANs, identified by a particular
lldpXdot1RemVlanId, received on the given port. LldpXdot1RemVlanNameEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.3.1 |
lldpXdot1RemVlanIdThe integer value used to identify the IEEE 802.1Q
VLAN IDs with which the given port of the remote system
is compatible. VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.171.10.76.28.1.32.13.3.3.1.1 |
lldpXdot1RemVlanNameThe string value used to identify VLAN name identified by the
VLAN Id associated with the remote system.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.32.13.3.3.1.2 |
lldpXdot1RemProtocolTableThis table contains one or more rows per protocol information
about the remote system, received on the given port. SEQUENCE OF LldpXdot1RemProtocolEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.4 |
lldpXdot1RemProtocolEntryProtocol information about a particular port component.
There may be multiple protocols, identified by a particular
lldpXdot1ProtocolIndex, received on the given port. LldpXdot1RemProtocolEntry .1.3.6.1.4.1.171.10.76.28.1.32.13.3.4.1 |
lldpXdot1RemProtocolIndexThis object represents an arbitrary local integer value used
by this agent to identify a particular protocol identity. Integer32 .1.3.6.1.4.1.171.10.76.28.1.32.13.3.4.1.1 |
lldpXdot1RemProtocolIdThe octet string value used to identify the protocols
associated with the given port of remote system.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.32.13.3.4.1.2 |
companyCPUInterfaceFilterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.33 |
cpuFilterProfile OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.33.1 |
ipv4cpuFilterProfileTableA table to CPUInterfaceFilter profile . SEQUENCE OF Ipv4CpuFilterProfileEntry .1.3.6.1.4.1.171.10.76.28.1.33.1.1 |
ipv4cpuFilterProfileEntryEach entry in this table is a CPUInterfaceFilter profile.
Index to the table is CPUInterfaceFilter profile ID. Ipv4CpuFilterProfileEntry .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1 |
ipv4cpuFilterProfileNoThe CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter,
and the ID more than 50 is reserved for system-defined CPUInterfaceFilter.
The user only allow to create user-defined CPUInterfaceFilter ID.
And system-defined CPUInterfaceFilter is read only.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.1 |
ipv4cpuFilterProfileTypeThe CPUInterfaceFilter Profile type, possible value are
l2 (1) - for MAC-based rule,
l3 (2) - for IPv4-based rule,rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.2 |
ipv4cpuFilterProfileRuleCountThe number of rules in this profile.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.3 |
ipv4cpuFilterProfileMaskIndicate which field want to care in the packet.
Turn on the following bits to select the following items
Type Item BIT
L2 DST_MAC 0 (LSB)
L2 SRC_MAC 1
L2 VID 2
L2 8021P_PRIORITY 3
L2 ETHER_TYPE 4
L3 DSCP 5
L3 ICMP_TYPE 6
L3 ICMP_CODE 7
L3 IGMP_TYPE 8
L3 DST_IP 9
L3 SRC_IP 10
L3 DST_PORT 11
L3 SRC_PORT 12
L3 TCPFLAG 13 (MSB)
The value is in Hex format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.4 |
ipv4cpuFilterProfileDstMacAddrMaskThe CPUInterfaceFilter Profile destination MAC address mask.
If DST_MAC is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL2RuleDstMacAddr,
to caculate a range of MAC address which is really care.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.5 |
ipv4cpuFilterProfileSrcMacAddrMaskThe CPUInterfaceFilter Profile source MAC address mask.
If SRC_MAC is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL2RuleSrcMacAddr,
to caculate a range of MAC address which is really care.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.6 |
ipv4cpuFilterProfileIPProtocolIndicate which IP Protocol will be care in this profile.
Only profile type is l3 can set the IP protocol.
For others, this field will be none.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.7 |
ipv4cpuFilterProfileIPProtocolMaskThe CPUInterfaceFilter Profile IP protocol mask.
If cpuFilterProfileIPProtocol set to ipMask, this field will be refered.
It will work with its member rule field,cpuFilterL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.8 |
ipv4cpuFilterProfileDstIpAddrMaskThe CPUInterfaceFilter Profile destination IP address mask.
If DST_IP is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleDstIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.9 |
ipv4cpuFilterProfileSrcIpAddrMaskThe CPUInterfaceFilter Profile source IP address mask.
If SRC_IP is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleSrcIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.10 |
ipv4cpuFilterProfileDstPortMaskThe CPUInterfaceFilter Profile UDP/TCP destination port mask.
If DST_PORT is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort,
to caculate a range of destination port which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.11 |
ipv4cpuFilterProfileSrcPortMaskThe CPUInterfaceFilter Profile UDP/TCP source port mask.
If SRC_PORT is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort,
to caculate a range of source port which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.12 |
ipv4cpuFilterProfileStatusThis object indicates the status of this entry, can only be set to
'createAndWait','active' and 'destroy'.
When the value of the entry status is 'createAndWait', it could be
set to 'active' only if the three values of cpuFilterProfileType,
cpuFilterProfileMask and ProtocolType are not conflicted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.1.1.1.15 |
cpuFilterProfileTableA table to CPUInterfaceFilter profile . SEQUENCE OF CpuFilterProfileEntry .1.3.6.1.4.1.171.10.76.28.1.33.1.2 |
cpuFilterProfileEntryEach entry in this table is a CPUInterfaceFilter profile.
Index to the table is CPUInterfaceFilter profile ID. CpuFilterProfileEntry .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1 |
cpuFilterProfileNoThe CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter,
and the ID more than 50 is reserved for system-defined CPUInterfaceFilter.
The user only allow to create user-defined CPUInterfaceFilter ID.
And system-defined CPUInterfaceFilter is read only.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.1 |
cpuFilterProfileTypeThe CPUInterfaceFilter Profile type, possible value are
l2 (1) - for MAC-based rule,
l3 (2) - for IPv4-based rule,rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.2 |
cpuFilterProfileRuleCountThe number of rules in this profile.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.3 |
cpuFilterProfileMaskIndicate which field want to care in the packet.
Turn on the following bits to select the following items
Type Item BIT
L2 DST_MAC 0 (LSB)
L2 SRC_MAC 1
L2 VID 2
L2 8021P_PRIORITY 3
L2 ETHER_TYPE 4
L3 DSCP 5
L3 ICMP_TYPE 6
L3 ICMP_CODE 7
L3 IGMP_TYPE 8
L3 DST_IP 9
L3 SRC_IP 10
L3 DST_PORT 11
L3 SRC_PORT 12
L3 TCPFLAG 13 (MSB)
L3 TRAFFIC_CLASS 21
The value is in Hex format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.4 |
cpuFilterProfileDstMacAddrMaskThe CPUInterfaceFilter Profile destination MAC address mask.
If DST_MAC is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL2RuleDstMacAddr,
to caculate a range of MAC address which is really care.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.5 |
cpuFilterProfileSrcMacAddrMaskThe CPUInterfaceFilter Profile source MAC address mask.
If SRC_MAC is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL2RuleSrcMacAddr,
to caculate a range of MAC address which is really care.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.6 |
cpuFilterProfileIPProtocolIndicate which IP Protocol will be care in this profile.
Only profile type is l3 can set the IP protocol.
For others, this field will be none.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.7 |
cpuFilterProfileIPProtocolMaskThe CPUInterfaceFilter Profile IP protocol mask.
If cpuFilterProfileIPProtocol set to ipMask, this field will be refered.
It will work with its member rule field,cpuFilterL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.8 |
cpuFilterProfileDstIpAddrMaskTypeIPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.9 |
cpuFilterProfileDstIpAddrMaskThe CPUInterfaceFilter Profile destination IP address mask.
If DST_IP is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleDstIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.10 |
cpuFilterProfileSrcIpAddrMaskTypeIPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.11 |
cpuFilterProfileSrcIpAddrMaskThe CPUInterfaceFilter Profile source IP address mask.
If SRC_IP is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleSrcIpAddr,
to caculate a range of IP address which is really care.
The value is in HEX format, for example:
'255.255.255.0' is presented to 'FFFFFF00'rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.12 |
cpuFilterProfileDstPortMaskThe CPUInterfaceFilter Profile UDP/TCP destination port mask.
If DST_PORT is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort,
to caculate a range of destination port which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.13 |
cpuFilterProfileSrcPortMaskThe CPUInterfaceFilter Profile UDP/TCP source port mask.
If SRC_PORT is turn on in cpuFilterProfileMask,
it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort,
to caculate a range of source port which is really care.
The value is in HEX format.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.14 |
cpuFilterProfileStatusThis object indicates the status of this entry, can only be set to
'createAndWait','active' and 'destroy'.
When the value of the entry status is 'createAndWait', it could be
set to 'active' only if the three values of cpuFilterProfileType,
cpuFilterProfileMask and ProtocolType are not conflicted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.1.2.1.15 |
cpuFilterL2Rule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.33.2 |
cpuFilterL2RuleTableA table to configure L2 filter rules in the system. SEQUENCE OF CpuFilterL2RuleEntry .1.3.6.1.4.1.171.10.76.28.1.33.2.1 |
cpuFilterL2RuleEntryEach entry in this table is a L2 filter rule.
Index to the table is the L2 filter number and Profile ID. CpuFilterL2RuleEntry .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1 |
cpuFilterL2ProfileIDL2 Filter rule ID.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.1 |
cpuFilterL2AccessIDCPUInterfaceFilter Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.2 |
cpuFilterL2RuleEtherTypeThe value in the Type/Len field of a frame that will
be matched to trigger this filter. The default value of
this object is '-1', which means the rule don't care this
condition.rw Integer32 (-1 | 1501..65535) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.3 |
cpuFilterL2RuleDstMacAddrDestination MAC address to be matched with the packet. By Default, the
Destination Mac Address will be zero,which means the rule don't care this
condition.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.4 |
cpuFilterL2RuleSrcMacAddrSource MAC address to be matched with the packet. By Default, the Source
Mac Address will be zero, which means the rule don't care this condition..
addressrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.5 |
cpuFilterL2RuleVlanIdVlan Id to be filtered. In case of Provider bridges, This Vlan Id will
be treated as customer Vlan Id. By Default, the value will be '-1',
which means the rule don't care this condition.rw Integer32 (-1..4094) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.6 |
cpuFilterL2Rule1pPriority802.1p priority to be matched with the packet. By Default, the value
will be '-1', which means the rule don't care this condition.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.7 |
cpuFilterL2RuleDstMacAddrMaskThe MAC address Mask work for Destination MAC address.
This field is read-only and copy from it's Profile setting.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.8 |
cpuFilterL2RuleSrcMacAddrMaskThe MAC address Mask work for Source MAC address.
This field is read-only and copy from it's Profile setting.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.9 |
cpuFilterL2RuleInPortListSpecifies the complete set of ports over which this filter is applied
for packets ingress at ports in this list.rw PortList .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.10 |
cpuFilterL2RuleActionSpecifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be forwarded according
to the forwarding rules.
If the action is 'drop', the packet will be discarded.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.11 |
cpuFilterL2RuleStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.2.1.1.14 |
cpuFilterL3Rule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.33.3 |
cpuFilterL3RuleTableA table to configure L3 filter rules in the system. SEQUENCE OF CpuFilterL3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.33.3.1 |
cpuFilterL3RuleEntryEach entry in this table is a L3 filter rule.
Index to the table is L3 filter number and Profile ID. CpuFilterL3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1 |
cpuFilterL3RuleProfileNoL3 Filter rule ID.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.1 |
cpuFilterL3RuleAccessIDThe Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.2 |
cpuFilterL3RuleProtocolThe type of protocol to be checked against the packet.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.3 |
cpuFilterL3RuleProtocolMaskThe IP protocol mask.
This field is read-only and copy from it's Profile setting.
It will work with the other field,cpuFilterL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.4 |
cpuFilterL3RuleICMPMessageTypeThe message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action set in cpuFilterL3RuleAction.
The default value is '-1',which means the rule don't care this
condition.
Some ICMP message types are:
echoReply(0),
destinationUnreachable(3),
sourceQuench(4),
redirect(5),
echoRequest(8),
timeExceeded(11),
parameterProblem(12),
timestampRequest(13),
timestampReply(14),
informationRequest(15),
informationReply(16),
addressMaskRequest(17),
addressMaskReply (18),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.5 |
cpuFilterL3RuleICMPMessageCodeThe message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action set in cpuFilterL3RuleAction.
The default value is '-1', which means the rule don't care this
condition.
Some ICMP message codes are :
networkUnreachable(0),
hostUnreachable(1),
protocolUnreachable(2),
portUnreachable(3),
fragmentNeed(4),
sourceRouteFail(5),
destNetworkUnknown(6),
destHostUnknown(7),
srcHostIsolated(8),
destNetworkAdminProhibited(9),
destHostAdminProhibited(10),
networkUnreachableTOS(11),
hostUnreachableTOS(12),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.6 |
cpuFilterL3RuleDstIpAddrDestination IP address to be matched with the packet.
The default value will be zero, which means the rule
don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.7 |
cpuFilterL3RuleSrcIpAddrSource IP address to be matched with the packet.
The default value will be zero, which means the
rule don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.8 |
cpuFilterL3RuleDstIpAddrMaskThe IP subnet mask for Destination IP address.
This field is read-only and copy from it's Profile setting.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.9 |
cpuFilterL3RuleSrcIpAddrMaskThe IP subnet mask for Source IP address.
This field is read-only and copy from it's Profile setting.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.10 |
cpuFilterL3RuleTcpUdpDstPortThe TCP / UDP destination port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.11 |
cpuFilterL3RuleTcpUdpSrcPortThe TCP / UDP source port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.12 |
cpuFilterL3RuleTcpUdpDstPortMaskThe TCP / UDP Destination port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.13 |
cpuFilterL3RuleTcpUdpSrcPortMaskThe TCP / UDP Source port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.14 |
cpuFilterL3RuleTcpAckBitThe TCP ACK bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.15 |
cpuFilterL3RuleTcpRstBitThe TCP RST bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.16 |
cpuFilterL3RuleTcpUrgBitThe TCP Urg bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.17 |
cpuFilterL3RuleTcpPshBitThe TCP Psh bit to be checked against the packet. The default
value is 'dontcare'(-1). which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.18 |
cpuFilterL3RuleTcpSynBitThe TCP Syn bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.19 |
cpuFilterL3RuleTcpFinBitThe TCP Fin bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.20 |
cpuFilterL3RuleDscpThe IP Dscp value to be checked against the packet.
A default value is '-1', which means the rule don't
care this condition.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.21 |
cpuFilterL3RuleIgmpTypeThe IGMP Type to be checked against the packet.A default value is '-1',
which means the rule don't care this condition.rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.22 |
cpuFilterL3RulePortListSpecifies the complete set of ports over which if the packet arrives
this filter rule will be applicable.rw PortList .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.23 |
cpuFilterL3RuleActionSpecifies the action to be taken on the packet if the filter
rule matches.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.24 |
cpuFilterL3RuleStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.3.1.1.27 |
cpuFilterv6L3RuleTableA table to configure L3 filter rules in the system. SEQUENCE OF CpuFilterv6L3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.33.3.2 |
cpuFilterv6L3RuleEntryEach entry in this table is a L3 filter rule.
Index to the table is L3 filter number and Profile ID. CpuFilterv6L3RuleEntry .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1 |
cpuFilterv6L3RuleProfileNoL3 Filter rule ID.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.1 |
cpuFilterv6L3RuleAccessIDThe Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.2 |
cpuFilterv6L3RuleProtocolThe type of protocol to be checked against the packet.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.3 |
cpuFilterv6L3RuleProtocolMaskThe IP protocol mask.
This field is read-only and copy from it's Profile setting.
It will work with the other field,cpuFilterL3RuleProtocol,
to caculate a range of IP protocol which is really care.
The value is in HEX format.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.4 |
cpuFilterv6L3RuleICMPMessageTypeThe message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action set in cpuFilterL3RuleAction.
The default value is '-1',which means the rule don't care this
condition.
Some ICMP message types are:
echoReply(0),
destinationUnreachable(3),
sourceQuench(4),
redirect(5),
echoRequest(8),
timeExceeded(11),
parameterProblem(12),
timestampRequest(13),
timestampReply(14),
informationRequest(15),
informationReply(16),
addressMaskRequest(17),
addressMaskReply (18),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.5 |
cpuFilterv6L3RuleICMPMessageCodeThe message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action set in cpuFilterL3RuleAction.
The default value is '-1', which means the rule don't care this
condition.
Some ICMP message codes are :
networkUnreachable(0),
hostUnreachable(1),
protocolUnreachable(2),
portUnreachable(3),
fragmentNeed(4),
sourceRouteFail(5),
destNetworkUnknown(6),
destHostUnknown(7),
srcHostIsolated(8),
destNetworkAdminProhibited(9),
destHostAdminProhibited(10),
networkUnreachableTOS(11),
hostUnreachableTOS(12),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.6 |
cpuFilterv6L3RuleDstIpAddrDestination IP address to be matched with the packet.
The default value will be zero, which means the rule
don't care this condition.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.7 |
cpuFilterv6L3RuleSrcIpAddrSource IP address to be matched with the packet.
The default value will be zero, which means the
rule don't care this condition.rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.8 |
cpuFilterv6L3RuleDstIpAddrMaskThe IP subnet mask for Destination IP address.
This field is read-only and copy from it's Profile setting.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.9 |
cpuFilterv6L3RuleSrcIpAddrMaskThe IP subnet mask for Source IP address.
This field is read-only and copy from it's Profile setting.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.10 |
cpuFilterv6L3RuleTcpUdpDstPortThe TCP / UDP destination port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.11 |
cpuFilterv6L3RuleTcpUdpSrcPortThe TCP / UDP source port. The default value is -1,
which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.12 |
cpuFilterv6L3RuleTcpUdpDstPortMaskThe TCP / UDP Destination port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.13 |
cpuFilterv6L3RuleTcpUdpSrcPortMaskThe TCP / UDP Source port Mask.
This field is read-only and copy from it's Profile setting.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.14 |
cpuFilterv6L3RuleTcpAckBitThe TCP ACK bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.15 |
cpuFilterv6L3RuleTcpRstBitThe TCP RST bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.16 |
cpuFilterv6L3RuleTcpUrgBitThe TCP Urg bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.17 |
cpuFilterv6L3RuleTcpPshBitThe TCP Psh bit to be checked against the packet. The default
value is 'dontcare'(-1). which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.18 |
cpuFilterv6L3RuleTcpSynBitThe TCP Syn bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.19 |
cpuFilterv6L3RuleTcpFinBitThe TCP Fin bit to be checked against the packet. The default
value is 'dontcare'(-1), which means the rule don't care this
condition.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.20 |
cpuFilterv6L3RuleTrafficClassThe IP Dscp value to be checked against the packet.
A default value is '-1', which means the rule don't
care this condition.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.21 |
cpuFilterv6L3RulePortListSpecifies the complete set of ports over which if the packet arrives
this filter rule will be applicable.rw PortList .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.22 |
cpuFilterv6L3RuleActionSpecifies the action to be taken on the packet if the filter
rule matches.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.23 |
cpuFilterv6L3RuleStatusThis object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in this table is not used when this
object is SET 'notInService'. An entry created in this table is
be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.33.3.2.1.24 |
companyStaticARP OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.34 |
staticARPTableA list of the Static MACs SEQUENCE OF StaticARPEntry .1.3.6.1.4.1.171.10.76.28.1.34.2 |
staticARPEntryA Static MAC entry containing the mac and forwarding port. StaticARPEntry .1.3.6.1.4.1.171.10.76.28.1.34.2.1 |
staticARPIPThe VLAN ID of the static ARP IP.ro IpAddress .1.3.6.1.4.1.171.10.76.28.1.34.2.1.2 |
staticARPMacThe MAC address associated of the static ARP entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.34.2.1.3 |
staticARPRowStatusThe status of an entry in the Static ARP Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available. The trunk member port can not set up static ARP.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.34.2.1.5 |
companyCableDiagnostic OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.35 |
cableDiagTableA table that contains the cable situation for each port. SEQUENCE OF CableDiagEntry .1.3.6.1.4.1.171.10.76.28.1.35.1 |
cableDiagEntryA list of cable situations for each port on the device. CableDiagEntry .1.3.6.1.4.1.171.10.76.28.1.35.1.1 |
cableDiagPortIndexThe interface index for which the configuration in this
entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.35.1.1.1 |
cableDiagPortTypeIndicates the supported port data rate classification.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.2 |
cableDiagLinkStatusThis object indicates the link status.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.3 |
cableDiagPair1StatusCable diagnostics pair 1 test result.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.4 |
cableDiagPair2StatusCable diagnostics pair 2 test result.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.5 |
cableDiagPair3StatusCable diagnostics pair 3 test result.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.6 |
cableDiagPair4StatusCable diagnostics pair 4 test result.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.7 |
cableDiagPair1LengthCable Diagnostics pair 1 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.35.1.1.8 |
cableDiagPair2LengthCable diagnostics pair 2 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.35.1.1.9 |
cableDiagPair3LengthCable diagnostics pair 3 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.35.1.1.10 |
cableDiagPair4LengthCable diagnostics pair 4 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.35.1.1.11 |
cableDiagActionFunction to run the cable diagnostic on selected port.
Can not detect fiber portsrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.12 |
cableDiagStatusIndicates the status of cable diagnostics on the port.
not-run - cable diagnostics has never been run for this port
processing - cable diagnostics is currently running on the port
last-test-ok - the last cable diagnostics done on the port was successful
last-test-failed - the last cable diagnostics done on the port failedro Enumeration .1.3.6.1.4.1.171.10.76.28.1.35.1.1.13 |
companyVLANTrunk OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.36 |
vlanTrunkSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.36.1 |
vlanTrunkGlobalStatusThis indicates the global state of the VLAN trunking feature of the device.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.36.1.1 |
vlanTrunkTableThis table is used to manage the VLAN trunking feature of the device. SEQUENCE OF VlanTrunkConfigEntry .1.3.6.1.4.1.171.10.76.28.1.36.1.2 |
vlanTrunkEntryThere is one entry in this table for each created
port-channel port. VlanTrunkConfigEntry .1.3.6.1.4.1.171.10.76.28.1.36.1.2.1 |
vlanTrunkIfIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.36.1.2.1.1 |
vlanTrunkStateSets the VLAN trunk status as enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.36.1.2.1.2 |
companyTimeRangeMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.38 |
swTimeRangeSettingTableA table to configure time Range in the system. SEQUENCE OF SwTimeRangeSettingEntry .1.3.6.1.4.1.171.10.76.28.1.38.1 |
swTimeRangeSettingEntryA schedule entry to configure time Range in the system. SwTimeRangeSettingEntry .1.3.6.1.4.1.171.10.76.28.1.38.1.1 |
swTimeRangeIndexThe Time Range identifier. The maximum number of Schedule entry is
the number of ports supported PoE function.
The value must be between 1 and 52.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.38.1.1.1 |
swTimeRangeNameThe Schedule name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.38.1.1.2 |
swTimeRangeDateEnable/Disable date range checking while executing time base PoE.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.3 |
swTimeRangeStartYearStart year of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.4 |
swTimeRangeStartMonthStart month of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.5 |
swTimeRangeStartDayStart day of the Schedule entry.
The value must be from 1 to 31.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.38.1.1.6 |
swTimeRangeStartHourStart hour of the Schedule entry.
The value must be from 0 to 23.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.38.1.1.7 |
swTimeRangeStartMinuteStart minute of the Schedule entry.
The value must be from 0 to 59.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.38.1.1.8 |
swTimeRangeEndYearEnd year of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.9 |
swTimeRangeEndMonthEnd month of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.10 |
swTimeRangeEndDayEnd day of the Schedule entry.
The value must be from 1 to 31.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.38.1.1.11 |
swTimeRangeEndHourEnd hour of the Schedule entry.
The value must be from 0 to 23.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.38.1.1.12 |
swTimeRangeEndMinuteEnd minute of the Schedule entry.
The value must be from 0 to 59.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.38.1.1.13 |
swTimeRangeMondayEnable/Disble scheduling Monday.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.14 |
swTimeRangeTuesdayEnable/Disble scheduling Tuesday.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.15 |
swTimeRangeWednesdayEnable/Disble scheduling Wednesday.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.16 |
swTimeRangeThursdayEnable/Disble scheduling Thursday.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.17 |
swTimeRangeFridayEnable/Disble scheduling Friday.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.18 |
swTimeRangeSaturdayEnable/Disble scheduling Saturday.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.19 |
swTimeRangeSundayEnable/Disble scheduling Sunday.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.38.1.1.20 |
swTimeRangeRowStatusThe status of an entry in the Time Range Information Table. Only a subset
of the rowstatus variables (active, notinservice, createAndWait, destroy)
are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.38.1.1.21 |
companySMTP OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.40 |
ipv4smtpStateEnable or Disable SMTP function.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.40.1 |
ipv4smtpServerAddrSMTP Server's IP Addressrwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.40.2 |
ipv4smtpServerPortSMTP Server's portrwobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.40.3 |
ipv4smtpSelfMailAddrThe sender's (DUT) mail address .rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.40.4 |
ipv4smtpRecvMailAddrTableReceivers' mail address table. SEQUENCE OF Ipv4SmtpRecvMailAddrEntry .1.3.6.1.4.1.171.10.76.28.1.40.5 |
ipv4smtpRecvMailAddrEntryReceivers' mail address entry. Ipv4SmtpRecvMailAddrEntry .1.3.6.1.4.1.171.10.76.28.1.40.5.1 |
ipv4smtpRecvMailAddrIndexReceivers' mail address index (1~8).ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.40.5.1.1 |
ipv4smtpRecvMailAddrReceivers' mail address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.40.5.1.2 |
ipv4smtpRecvMailAddrStatusRowstatus of the receiver's mail address.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.40.5.1.3 |
sysSMTPServerGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.40.6 |
smtpStateEnable or Disable SMTP function.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.40.6.1 |
smtpServerAddrSMTP Server's IP Addressrw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.40.6.2 |
smtpServerAddrTypeSMTP Server's Address type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.40.6.3 |
smtpServerAddrInterfaceNameSpecifies the interface name when the smtpServerAddrInterfaceName is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.40.6.4 |
smtpServerPortSMTP Server's portrw INTEGER .1.3.6.1.4.1.171.10.76.28.1.40.6.5 |
smtpSelfMailAddrThe sender's (DUT) mail address .rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.40.6.6 |
smtpRecvMailAddrTableReceivers' mail address table. SEQUENCE OF SmtpRecvMailAddrEntry .1.3.6.1.4.1.171.10.76.28.1.40.6.7 |
smtpRecvMailAddrEntryReceivers' mail address entry. SmtpRecvMailAddrEntry .1.3.6.1.4.1.171.10.76.28.1.40.6.7.1 |
smtpRecvMailAddrIndexReceivers' mail address index (1~8).ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.40.6.7.1.1 |
smtpRecvMailAddrReceivers' mail address.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.40.6.7.1.2 |
smtpRecvMailAddrStatusRowstatus of the receiver's mail address.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.40.6.7.1.3 |
companyMultiIPInterface OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.41 |
ipv4multiIFInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.41.1 |
ipv4mulIfMainTableA list of interface entries.obsolete SEQUENCE OF Ipv4MulIfMainEntry .1.3.6.1.4.1.171.10.76.28.1.41.1.1 |
ipv4mulIfMainEntryAn entry containing management information applicable
to a particular interface.obsolete Ipv4MulIfMainEntry .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1 |
ipv4mulifMainIndexThe index of this interface.roobsolete InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.1 |
ipv4mulifVLANIDThe ID of VLAN that you want this interface to be in.
It must be a exist vlan id.roobsolete INTEGER .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.2 |
ipv4mulifNameThe Description for the interface.rwobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.3 |
ipv4mulifVLANnameThe vlan name for the interface.roobsolete OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.4 |
ipv4mulifIpAddrThe ip address of this interface.rwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.6 |
ipv4mulifIpSubnetMaskThe subnet mask of this interface.rwobsolete IpAddress .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.7 |
ipv4mulifMainAdminStatusThe desired state of the interface.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.8 |
ipv4mulifMainOperStatusThe current operational state of the interface.roobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.9 |
ipv4mulifMainRowStatusThe status of an entry in the Multi Interface Table. Only a subset
of the rowstatus variables (active, createAndWait, destroy) are available.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.41.1.1.1.10 |
multiIFSupportV4V6Info OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.41.2 |
mulIfSupportV4V6MainTableA list of interface entries. SEQUENCE OF MulIfSupportV4V6MainEntry .1.3.6.1.4.1.171.10.76.28.1.41.2.1 |
mulIfSupportV4V6MainEntryAn entry containing management information applicable
to a particular interface. MulIfSupportV4V6MainEntry .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1 |
mulifMainIndexThe index of this interface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.1 |
mulifVLANIDThe ID of VLAN that you want this interface to be in.
It must be a exist vlan id.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.2 |
mulifNameThe Description for the interface.rw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.3 |
mulifVLANnameThe vlan name for the interface.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.4 |
mulifIpAddrThe ip address of this interface.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.5 |
mulifIpSubnetMaskThe subnet mask of this interface.rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.6 |
mulifMainAdminStatusThe desired state of the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.7 |
mulifMainOperStatusThe current operational state of the interface.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.8 |
mulifv6GlobalStatusThe ID of VLAN that you want this interface to be in.
It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.9 |
mulifv6DHCPStatusThe state of DHCPv6 that you want this interface to be in.
It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.10 |
mulifv6AutolinkloStatusThe global state of link local that you want this interface to be in.
It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.11 |
mulifv6NSRetransmitTimeThe NS's retransmit time that you want this interface to be in.
It must be a exist vlan id.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.12 |
mulifMainRowStatusThe status of an entry in the Multi Interface Table. Only a subset
of the rowstatus variables (active, createAndWait, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.41.2.1.1.13 |
mulIfV6AddressTableA list of interface entries. SEQUENCE OF MulIfV6AddressEntry .1.3.6.1.4.1.171.10.76.28.1.41.2.2 |
mulIfV6AddressEntryAn entry containing management information applicable
to a particular interface. MulIfV6AddressEntry .1.3.6.1.4.1.171.10.76.28.1.41.2.2.1 |
mulifV6AddressMainIndexThe index of this IPv6 entry.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.41.2.2.1.1 |
mulifV6AddressIpAddrThe ip address of this IPv6 entry.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.41.2.2.1.2 |
mulifV6AddressIpPrefixThe ip prefix of this IPv6 entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.41.2.2.1.3 |
mulifV6AddressIpTypeThe ip type of this IPv6 entry.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.41.2.2.1.4 |
mulifV6AddressRowStatusThe status of an entry in the Multi Interface Table. Only a subset
of the rowstatus variables (active, createAndWait, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.41.2.2.1.5 |
companyLimitIp OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.45 |
limitIpMulticastProfileTableA list of the limit ip multicast Profile Table. SEQUENCE OF LimitIpMulticastProfileEntry .1.3.6.1.4.1.171.10.76.28.1.45.1 |
limitIpMulticastProfileEntryA limit ip multicast entry maintain by the start IP Address, end ip address, profile id. LimitIpMulticastProfileEntry .1.3.6.1.4.1.171.10.76.28.1.45.1.1 |
limitIpMulticastIPTypeIndicate the IP type of profile.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.45.1.1.1 |
limitIpMulticastProfileIDThe ProfileID of the limit ip multicast profile entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.45.1.1.2 |
limitIpMulticastProfileNameThe ProfileName of the limit ip multicast profile entry.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.45.1.1.3 |
limitIpMulticastProfileStatusThe status of an entry in the limit ip multicast profile Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.45.1.1.4 |
limitIpMulticastEntryTableA list of the limit ip multicast entry Table. SEQUENCE OF LimitIpMulticastEntry .1.3.6.1.4.1.171.10.76.28.1.45.2 |
limitIpMulticastEntryA limit ip multicast entry maintain by the start IP Address, end ip address, profile id. LimitIpMulticastEntry .1.3.6.1.4.1.171.10.76.28.1.45.2.1 |
limitIpMulticastEntryIPTypeIndicate the IP type of entry.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.45.2.1.1 |
limitIpMulticastEntryProfileIDThe ProfileID of the limit ip multicast entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.45.2.1.2 |
limitIpMulticaststartIpAddrThe limit ip multicast IP address is used to set start ipro DisplayString .1.3.6.1.4.1.171.10.76.28.1.45.2.1.3 |
limitIpMulticastendIpAddrThe limit ip multicast IP address is used to set end ipro DisplayString .1.3.6.1.4.1.171.10.76.28.1.45.2.1.4 |
limitIpMulticastStatusThe status of an entry in the limit ip multicast entry Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.45.2.1.5 |
limitIpMulticastPortTableA list of the limit ip multicast Port entry Table. SEQUENCE OF LimitIpMulticastPortEntry .1.3.6.1.4.1.171.10.76.28.1.45.3 |
limitIpMulticastPortEntryA limit ip multicast entry maintain by the Port Index. LimitIpMulticastPortEntry .1.3.6.1.4.1.171.10.76.28.1.45.3.1 |
limitIpMulticastPortIPTypeIndicate the IP type of entry.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.45.3.1.1 |
limitIpMulticastPortIDThe Port Index of the limit ip multicast port entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.45.3.1.2 |
limitIpMulticastPortStateThe limit ip multicast port staterw Enumeration .1.3.6.1.4.1.171.10.76.28.1.45.3.1.3 |
limitIpMulticastPortProfileIDThe limit ip multicast port mapping profileID list.rw PortList .1.3.6.1.4.1.171.10.76.28.1.45.3.1.4 |
limitIpMulticastPortMaxGrpThe limit ip multicast per-port max group.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.45.3.1.5 |
companyGratuitousARP OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.48 |
sysGratuitousARPGlobalSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.48.1 |
sysGratuitousARPIPIfStatusUpThis object indicates Send On IP Interface Status Up is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.48.1.1 |
sysGratuitousARPDuplicateIPDetectedThis object indicates Send On Duplicate IP Detected is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.48.1.2 |
sysGratuitousARPLearningThis object indicates Gratuitous ARP Learning is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.48.1.3 |
sysGratuitousARPSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.48.2 |
sysGratuitousARPTableSet/Add Gratuitous ARP interface name and interval time. SEQUENCE OF SysGratuitousARPEntry .1.3.6.1.4.1.171.10.76.28.1.48.2.1 |
sysGratuitousARPEntryThe entry of gratuitous ARP! SysGratuitousARPEntry .1.3.6.1.4.1.171.10.76.28.1.48.2.1.1 |
sysGratuitousARPIFNameInterface name.ro OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.48.2.1.1.1 |
sysGratuitousARPIntervalGratuitous ARP interval time for each interface.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.48.2.1.1.2 |
companyNeighbor OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.50 |
neighborTableA list of the Neighbor Cache Table. SEQUENCE OF NeighborEntry .1.3.6.1.4.1.171.10.76.28.1.50.1 |
neighborEntryA Neighbor cache entry containing the ifindex and ipv6 addr. NeighborEntry .1.3.6.1.4.1.171.10.76.28.1.50.1.1 |
neighborIfindexThe interface index of the Neighbor entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.50.1.1.1 |
neighborIPv6AddrAllows the entry of an IP address that will be a Neighbor entry into
the Neighbor Cache Table.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.50.1.1.2 |
neighborMACAddrThe MAC address associated of the Neighbor entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.50.1.1.3 |
neighborTypeThe type associated of the Neighbor entry.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.50.1.1.4 |
neighborCacheStateThe type associated of the Neighbor entry.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.50.1.1.5 |
neighborActiveStatusThe active status of the Neighbor entry.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.50.1.1.6 |
neighborRowStatusThe status of an entry in the Neighbor Cache Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.50.1.1.7 |
companyEoam OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.51 |
eoamSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.51.1 |
eoamTableA table that contains EOAM mode information about each port. SEQUENCE OF EOAMConfigEntry .1.3.6.1.4.1.171.10.76.28.1.51.1.2 |
eoamEntryA list of EOAM mode information for each port. EOAMConfigEntry .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1 |
eoamIfIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1.1 |
eoamStateSets the EOAM state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1.2 |
eoamModeSets the EOAM mode as active or passive.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1.3 |
eoamReceivedRemoteLoopbackSets the EOAM received or ignore remote loopback packets.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1.4 |
eoamRemoteLoopbackSets the EOAM remote loopback start or stop.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1.5 |
eoamDyingGaspEnableSets the EOAM dying gasp state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1.6 |
eoamCriticalEventEnableSets the EOAM critical event state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.1.2.1.7 |
eoamLinkMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.51.2 |
eoamLinkMonitorTableA table that contains EOAM link monitor information about each port. SEQUENCE OF EOAMConfigLinkMonitorEntry .1.3.6.1.4.1.171.10.76.28.1.51.2.1 |
eoamLinkMonitorEntryA list of EOAM link monitor information for each port. EOAMConfigLinkMonitorEntry .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1 |
eoamLinkMonitorIfIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.1 |
errorSymbolNotifyStateSets the EOAM error symbol notify state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.2 |
errorSymbolThresholdSets the EOAM error symbol threshold.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.3 |
errorSymbolWindowSets the EOAM error symbol window.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.4 |
errorFrameNotifyStateSets the EOAM error frame notify state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.5 |
errorFrameThresholdSets the EOAM error frame threshold.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.6 |
errorFrameWindowSets the EOAM error symbol window.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.7 |
errorFrameSecondsNotifyStateSets the EOAM error symbol notify state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.8 |
errorFrameSecondsThresholdSets the EOAM error symbol threshold.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.9 |
errorFrameSecondsWindowSets the EOAM error symbol window.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.10 |
errorFramePeriodNotifyStateSets the EOAM error symbol notify state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.11 |
errorFramePeriodThresholdSets the EOAM error symbol threshold.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.12 |
errorFramePeriodWindowSets the EOAM error symbol window.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.51.2.1.1.13 |
companyDuld OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.52 |
duldSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.52.1 |
duldTableA table that contains DULD mode information about each port. SEQUENCE OF DULDConfigEntry .1.3.6.1.4.1.171.10.76.28.1.52.1.1 |
duldEntryA list of DULD mode information for each port. DULDConfigEntry .1.3.6.1.4.1.171.10.76.28.1.52.1.1.1 |
duldIfIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.52.1.1.1.1 |
duldStateSets the DULD admin state enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.52.1.1.1.2 |
duldOperStateGets the DULD Oper state enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.52.1.1.1.3 |
duldModeSets the DULD mode as shutdown or normal.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.52.1.1.1.4 |
duldLinkStatusGets the DULD link status.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.52.1.1.1.5 |
duldDiscoveryTimeSets the DULD discovery time.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.52.1.1.1.6 |
duldRecoverTimeDuld auto recover time.rw Integer32 (0 | 60..1000000) .1.3.6.1.4.1.171.10.76.28.1.52.1.2 |
companydot3azEEE OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.53 |
dot3azEEEset OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.53.1 |
dot3azTableA table to control IEEE802.3az EEE settings features of the device. SEQUENCE OF Dot3azEntry .1.3.6.1.4.1.171.10.76.28.1.53.1.1 |
dot3azEntryAn entry appears in IEEE802.3az EEE table for each interface
in the system. Dot3azEntry .1.3.6.1.4.1.171.10.76.28.1.53.1.1.1 |
portD3IndexThe interface index for which the configuration in this
entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.53.1.1.1.1 |
portD3StateEnable / disable port IEEE802.3az EEE admin state for the interface.
A given ports' dynamic MAC address learning will be stopped such
that the current source MAC addresses entered into the MAC address
forwarding table can not be changed once the port security admin
state is enabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.53.1.1.1.2 |
companyMacAuthGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.54 |
macBasedCtrlGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.54.1 |
macBasedCtrlStateEnable/Disable MAC-based Access Control Global Settings.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.1.1 |
macBasedMethodSelect MAC-based Access Control Methods.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.1.2 |
macBasedRadiusPasswordSet the password about the method Mac-Based Authentication,
the maximum length are 32 chars.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.54.1.3 |
macBasedRadiusAuthStatusThe state of Radius Authorization.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.1.4 |
macBasedLocalAuthStatusThe state of Local Authorization.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.1.5 |
macBasedTrapStatusThe state of Trap of MAC-based Authorization.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.1.6 |
macBasedLogStatusrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.1.7 |
macBasedMaxUsrrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.54.1.8 |
macBasedPortCtrlTable SEQUENCE OF MacBasedPortCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.54.1.11 |
macBasedPortCtrlEntry MacBasedPortCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.54.1.11.1 |
macBasedPortCtrlIndexro Integer32 .1.3.6.1.4.1.171.10.76.28.1.54.1.11.1.1 |
macBasedPortCtrlStaterw Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.1.11.1.2 |
macBasedPortCtrlAgingTimerw Integer32 .1.3.6.1.4.1.171.10.76.28.1.54.1.11.1.3 |
macBasedPortCtrlBlockTimerw Integer32 .1.3.6.1.4.1.171.10.76.28.1.54.1.11.1.4 |
macBasedPortCtrlMaxUsrrw Integer32 .1.3.6.1.4.1.171.10.76.28.1.54.1.11.1.5 |
macBasedCtrlLocalGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.54.2 |
macBasedCtrlLocalTable SEQUENCE OF MacBasedCtrlLocalEntry .1.3.6.1.4.1.171.10.76.28.1.54.2.1 |
macBasedCtrlLocalEntry MacBasedCtrlLocalEntry .1.3.6.1.4.1.171.10.76.28.1.54.2.1.1 |
macBasedCtrlLocalMacAddressThe MacAddress of the MAC-based Access Control Local Setting Table.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.54.2.1.1.1 |
macBasedCtrlLocalVIDThe VLAN ID of the MAC-based Access Control Local Setting entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.54.2.1.1.2 |
macBasedCtrlLocalVlanNameAn administratively assigned string, which may be used
to identify the VLAN.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.54.2.1.1.3 |
macBasedCtrlLocalRowStatusThe Row status of an entry in the MAC-based Access Control Local Setting Table.
Only a subset of the rowstatus variables (active, createAndGo, destroy) are availablerw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.54.2.1.1.4 |
macBasedCtrlAuthGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.54.3 |
macBasedCtrlAuthTable SEQUENCE OF MacBasedCtrlAuthEntry .1.3.6.1.4.1.171.10.76.28.1.54.3.1 |
macBasedCtrlAuthEntry MacBasedCtrlAuthEntry .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1 |
macBasedCtrlAuthPortro Integer32 .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.1 |
macBasedCtrlAuthMacAddressThe MacAddress of the MAC-based Access Control Authentication State Table.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.2 |
macBasedCtrlAuthRxVIDro INTEGER .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.3 |
macBasedCtrlAuthStatero Enumeration .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.4 |
macBasedCtrlAuthVIDro INTEGER .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.5 |
macBasedCtrlAuthPriorityro INTEGER .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.6 |
macBasedCtrlAuthAgingTimero INTEGER .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.7 |
macBasedCtrlAuthBlockTimero INTEGER .1.3.6.1.4.1.171.10.76.28.1.54.3.1.1.8 |
companyWACAuthGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.55 |
wacAuthCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.55.1 |
wacStatusEnable/Disable WAC Global Settingsrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.55.1.1 |
wacVirtualIPv4Virtual IPv4rw IpAddress .1.3.6.1.4.1.171.10.76.28.1.55.1.2 |
wacVirtualIPv6Virtual IPv6rw Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.55.1.3 |
wacRedirPathRedirection Pathrw OCTET STRING .1.3.6.1.4.1.171.10.76.28.1.55.1.4 |
wacClrRedirPathyes/no WAC Clear Redirection path Settingsrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.55.1.5 |
wacRadiusAuthEnable/Disable WAC RADIUS AUTH Settingsrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.55.1.6 |
waclocalAuthEnable/Disable WAC LOCAL AUTH Settingsrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.55.1.7 |
wacAuthMethodEnable/Disable WAC Auth Method Settingsrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.55.1.8 |
wacAuthPortMethodAuthorization Port Methodrw Enumeration .1.3.6.1.4.1.171.10.76.28.1.55.1.9 |
wacAuthPortHTTP(s) Port.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.1.10 |
wacUsrCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.55.2 |
wacUsrCtrlTableA table that contains the configuration objects for the
Authenticator PAE associated with each port.
An entry appears in this table for each port that may
authenticate access to itself. SEQUENCE OF WACUsrCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.55.2.1 |
wacUsrCtrlEntryThe configuration information for an Authenticator Port. WACUsrCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.55.2.1.1 |
authUserNameThe unique index value of a row in this table.
This object is used to set 802.1X Local user name,
The following characters are allowed to input:
semicolon, question mark, space, and double quotation mark.ro SnmpAdminString .1.3.6.1.4.1.171.10.76.28.1.55.2.1.1.1 |
authUserVIDThe ID of VLAN that you want this interface to be in.
It must be a exist vlan id.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.2.1.1.2 |
authUserPasswordThis object is used to set 802.1X Local user Password,
The following characters are allowed to input:
semicolon, question mark, space, and double quotation mark.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.55.2.1.1.3 |
authUserStatusThe status of this conceptual row in the swAuthUserTable.
An entry in this table is not qualified for activation
until instances of all corresponding columns have been
initialized, either through default values, or through
Set operations. The swAuthUserName objects must be
explicitly set.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.55.2.1.1.4 |
wacPortCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.55.3 |
wacPortCtrlTableA table to control the port specific parameters of the device like speed,
duplex mode, etc. SEQUENCE OF WACPortCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.55.3.1 |
wacPortCtrlEntryAn entry appears in this table for each interface in the system.
Index to the table is the interface index of the port. WACPortCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.55.3.1.1 |
wacPortCtrlIndexInterface index of the port for the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.55.3.1.1.1 |
wacPortCtrlStateEnables / disables flow control for the interface.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.55.3.1.1.2 |
wacPortCtrlAgetimeAging timerw INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.3.1.1.3 |
wacPortCtrlBlocktimeAging timerw INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.3.1.1.4 |
wacAuthState OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.55.4 |
wacAuthStateTableA list of the Auth States SEQUENCE OF WACAuthStateEntry .1.3.6.1.4.1.171.10.76.28.1.55.4.1 |
wacAuthStateEntryA Auth State entry containing the mac and forwarding port. WACAuthStateEntry .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1 |
wacAuthStatePortThe auth port state of the Auth State entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.1 |
wacAuthStateMacThe auth state mac of the Auth State entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.2 |
wacAuthStateRXVIDThe Rx VID of the Auth State entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.3 |
wacAuthStateflagThe auth state flag of the Auth State entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.4 |
wacAuthStateVIDThe auth state VID of the Auth State entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.5 |
wacAuthAssignPriorityThe auth assign priority of the Auth State entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.6 |
wacAuthStateAgetimeThe auth state age time of the Auth State entry.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.7 |
wacAuthStateRowStatusThe auth state row status.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.55.4.1.1.99 |
companyMacBasedVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.70 |
macBasedVlanTableA table that contains information on Vlan-MAC address
mapping. SEQUENCE OF MacBasedVlanEntry .1.3.6.1.4.1.171.10.76.28.1.70.1 |
macBasedVlanEntryEntry that contains Vlan-MAC address mapping. MacBasedVlanEntry .1.3.6.1.4.1.171.10.76.28.1.70.1.1 |
vlanMacMapIndexIndex of cmMacBasedVlanEntry. This object indicates the mac vlan entry for which
the configurations in cmMacBasedVlanEntry is to be done.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.70.1.1.1 |
vlanMacMapAddrThe Mac address for which the Vlan mapping is present in the entry.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.70.1.1.2 |
vlanMacMapAddrMaskThe Mac address for which the Vlan mapping is present in the entry.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.70.1.1.3 |
vlanMacMapVidThe Vlan to which the mac address of this entry is mapped to.rw VlanIndex .1.3.6.1.4.1.171.10.76.28.1.70.1.1.4 |
vlanMacStatusThe status given to the mac-vlan entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.70.1.1.5 |
vlanMacTypeThe type given to the mac-vlan entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.70.1.1.6 |
vlanMacMapRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.70.1.1.99 |
macBasedVlanMethodA method of Vlan-MAC address mapping.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.70.2 |
companyBPDUAttack OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.77 |
sysBPDUAttackStateEnableUse this to enable BPDU attack protection.
The BPDU Attack Protection function and Spanning Tree Protocol
for ports are mutually exclusive. When the STP function is enabled
on a particular port, BPDU Attack Protection cannot be enabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.77.1 |
sysBPDUAttackRecoverTimeWhen a port enters under attack state, it can be disabled or blocked
based on the configuration. The state can be recovered manually or
by the auto recovery mechanism. This command is used to configure the
auto-recovery timer. To manually recover the port, the user needs to
disable and re-enable the port.rw Integer32 (0 | 60..1000000) .1.3.6.1.4.1.171.10.76.28.1.77.2 |
sysBPDUAttackCtrlTableA table to control BPDU Attack features either for
the entire switch or for each interface in the switch. SEQUENCE OF SysBPDUAttackCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.77.3 |
sysBPDUAttackCtrlEntryAn entry appears in this table for each interface
in the system. SysBPDUAttackCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.77.3.1 |
sysBPDUAttackCtrlIndexThe interface index of the port for which the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.77.3.1.1 |
sysBPDUAttackPortStateUsed to configure the BPDU Attack Protection state of a port.
The default state is disable.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.77.3.1.2 |
sysBPDUAttackPortModeUsed to configure the BPDU Attack Protection mode of a port.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.77.3.1.3 |
sysBPDUAttackPortStatusUse this to view per port BPDU attack protection status.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.77.3.1.4 |
sysBPDUAttackLogUsed to configure log settings for BPDU attack protection events.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.77.4 |
companyDHCPv6Relay OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.86 |
dhcpv6RelayControl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.86.1 |
dhcpv6RelayStateThis object indicates DHCPv6 relay function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.1.1 |
dhcpv6RelayHopCountThis object indicates the maximum number of router hops that the DHCPv6 packets can cross.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.86.1.2 |
dhcpv6RelayManagement OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.86.2 |
dhcpv6RelayInterfaceSettingsTableThis table indicates the IP address as a destination to forward (relay) DHCP packets to. SEQUENCE OF DHCPv6RelayInterfaceSettings .1.3.6.1.4.1.171.10.76.28.1.86.2.1 |
dhcpv6RelayInterfaceSettingsEntryA list of information indicates the IP address as a destination to forward (relay) DHCP packets to. DHCPv6RelayInterfaceSettings .1.3.6.1.4.1.171.10.76.28.1.86.2.1.1 |
dhcpv6RelayInterfaceThis object indicates the maximum number of router hops that the DHCPv6 packets can cross.ro DisplayString .1.3.6.1.4.1.171.10.76.28.1.86.2.1.1.1 |
dhcpv6RelayServerIPThis object indicates the DHCP server IP address.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.86.2.1.1.2 |
dhcpv6RelayInterfaceSettingsRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.86.2.1.1.99 |
dhcpv6RelayOption37 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.86.3 |
dhcpv6RelayOption37StateThis object indicates DHCPv6 relay option 37 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.3.1 |
dhcpv6RelayOption37CheckStateThis object indicates DHCPv6 relay option 37 Check function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.3.2 |
dhcpv6RelayOption37RemoteIDTypeThis object indicates the type of remote ID.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.3.3 |
dhcpv6RelayOption37RemoteIDThis object displays the current remote ID of the device.
If RemoteIDType is set to default, the value will be the MAC address of the device,
and this object cannot be modified.
If RemoteIDType is set to user-defined, a new value can be written to this object.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.86.3.4 |
dhcpv6RelayOption38 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.86.4 |
dhcpv6RelayOpt38TableA table to control port security features of the device. SEQUENCE OF Dhcpv6RelayOpt38Entry .1.3.6.1.4.1.171.10.76.28.1.86.4.1 |
dhcpv6RelayOpt38EntryAn entry appears in port security table for each interface
in the system. Dhcpv6RelayOpt38Entry .1.3.6.1.4.1.171.10.76.28.1.86.4.1.1 |
dhcpv6RelayOpt38PortIndexThe interface index for which the configuration in this
entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.86.4.1.1.1 |
dhcpv6RelayOpt38PortStateEnable / disable option 38 port state.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.4.1.1.2 |
dhcpv6RelayOpt38PortTypeConfigure option 38 port Type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.4.1.1.3 |
dhcpv6RelayOpt38PortIDConfigure option 38 port ID. Only works when type is user-definedrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.86.4.1.1.4 |
dhcpv6RelayOption18 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.86.5 |
dhcpv6RelayOption18StateThis object indicates DHCPv6 relay option 18 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.5.1 |
dhcpv6RelayOption18CheckStateThis object indicates DHCPv6 relay option 18 Check function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.5.2 |
dhcpv6RelayOption18InterfaceIDTypeThis object indicates the type of Interface ID.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.86.5.3 |
companyMldsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.88 |
mldsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.88.1 |
mldsStatusEnables or disables MLD snooping in the system.
When set to 'enabled', the MLDS module starts
protocol operations.
When set to 'disabled', the MLDS module stops performing
protocol operations.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.88.1.1 |
mldsRouterPortPurgeIntervalThis is the interval (in seconds) after which a learnt
router port entry will be purged. For each router port learnt,
this timer runs for 'RouterPortPurgeInterval' seconds.When the
timer expires, the learnt router port entry is purged. However
if control messages are received from the router before the
timer expiry, then the timer is restarted.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.1.2 |
mldsHostPortPurgeIntervalThis is the interval (in seconds) after which a learnt
port entry will be purged. For each port on which report
has been received this timer runs for 'PortPurgeInterval'
seconds. This timer will be restarted whenever a report
message is received from a host on the specific port. If
the timer expires, then , the learnt port entry will
be purged from the multicast group.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.1.3 |
mldsDataDrivenLearningMaxLearnedEntryVlaueThe maximum data driven learning entry value.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.88.1.8 |
mldsVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.88.3 |
mldsVlanRouterTableThis table contains the list of ports through which
a router, in a particular VLAN is reachable. SEQUENCE OF MldsVlanRouterEntry .1.3.6.1.4.1.171.10.76.28.1.88.3.3 |
mldsVlanRouterEntryContains the VLAN ID and list of ports on which
routers are present in the VLAN. MldsVlanRouterEntry .1.3.6.1.4.1.171.10.76.28.1.88.3.3.1 |
mldsVlanRouterVlanIdVLAN ID of the ports through which router is reachable.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.3.3.1.1 |
mldsVlanRouterPortListList of ports on which routers are present.
These router ports are learnt through control messages
received from routers, and can also be configured
statically.ro PortList .1.3.6.1.4.1.171.10.76.28.1.88.3.3.1.2 |
mldsVlanFilterTableThis table contains configuration of snooping
on specific Vlans. This Table is valid only when VLAN is
enabled in the system. SEQUENCE OF MldsVlanFilterEntry .1.3.6.1.4.1.171.10.76.28.1.88.3.4 |
mldsVlanFilterEntryContains snooping status , version and fast leave
configuration for a specific VLAN. MldsVlanFilterEntry .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1 |
mldsVlanFilterVlanIdIndex of MldsVlanFilterEntry. This object indicates the VLAN ID for which
the snooping configurations in MldsVlanFilterEntry is to be done.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.1 |
mldsVlanSnoopStatusThis object allows you to enable/disable MLDS function on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.2 |
mldsVlanQuerierIndicates whether the switch is configured as a querier in the VLANro Enumeration .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.3 |
mldsVlanCfgQuerierThe snooping switch can be configured as a querier via this object
to send out MLD general queries when IGMP routers are not present in the VLAN.
When set to 'enabled', the switch will generate general queries.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.4 |
mldsVlanQueryIntervalThis is the interval (in seconds) for which the switch
sends general queries when it is configured as a querier for
the VLAN. A switch should be configured as a querier for a VLAN
only when there is no queriers in the network.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.5 |
mldsVlanRtrPortListList of ports which are configured statically as router portsrw PortList .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.6 |
mldsVlanFbdRtrPortListList of ports which can be configured statically as forbidden router ports.rw PortList .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.7 |
mldsVlanFastLeaveEnables or disables fast leave for the VLAN. When it is
'disabled',on reception of a leave message, the switch checks
if they are any interested receivers for the group by sending
a group specific query before removing the port from the
forwarding table. If set to 'enabled', the switch does not
send a group specific query and immediately removes the port
from the forwarding table.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.8 |
mldsVlanDataDrivenLearningStatusThis object allows you to enable/disable
Data Driven Learning function on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.9 |
mldsVlanReportSuppressionEnables or disables Report suppression in the system.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.10 |
mldsVlanRobustnessValueWhen the switch receives leave message on a port, it
sends group specific query to check if there are any other
interested receivers for the group. This attribute defines
the maximum number of queries sent by the switch before deleting
the port from the group membership information in the forwarding
database. If the maximum retry count exceeds 'mldsRobustnessValue',
then the port will be deleted from the multicast group membership
information in the forwarding database and received leave message
will be forwarded onto the router ports if there are no
interested receivers for the group.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.11 |
mldsVlanGrpQueryIntervalThe value of this attribute defines the time period with which
the switch will send group specific queries on a port to check
if there is any intersted receivers. The switch will send
'mldsRobustnessValue' queries before removing the port from the
group membership information in the forwarding database.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.12 |
mldsVlanQueryMaxResponseTimeThe maximum query response time advertised in MLDv1 general
queries on this interface.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.88.3.4.1.13 |
mldsVlanMulticastGroupTableThis table contains MAC based multicast forwarding
information. SEQUENCE OF MldsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.76.28.1.88.3.5 |
mldsVlanMulticastGroupEntryThis table contains VLAN ID, multicast group MAC address and the
list of ports onto which the multicast data packets for group
should be forwarded. MldsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.76.28.1.88.3.5.1 |
mldsVlanMulticastGroupVlanIdVLAN ID pertaining to the Multicast forwarding entryro Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.3.5.1.1 |
mldsVlanMulticastGroupIpAddressMulticast group IP address. This object indicates that a
multicast group address was learned in the switch and be represented
as IP address format.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.10.76.28.1.88.3.5.1.2 |
mldsVlanMulticastGroupMacAddressMulticast group MAC address. This object indicates that a
multicast group address was learned in the switch and be represented
as MAC address format.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.88.3.5.1.3 |
mldsVlanMulticastGroupPortListList of ports onto which the multicast data
packets destined for this group will be forwarded.ro PortList .1.3.6.1.4.1.171.10.76.28.1.88.3.5.1.4 |
mldsHost OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.88.4 |
mldsHostTableThis table is used to manage
the IGMP Host based Fast Leave function of the switch. SEQUENCE OF MldsHostEntry .1.3.6.1.4.1.171.10.76.28.1.88.4.1 |
mldsHostEntryContains management entities for
IGMP Host based fast leave function. MldsHostEntry .1.3.6.1.4.1.171.10.76.28.1.88.4.1.1 |
mldsHostTableVLANIDVLAN ID of IPv6 Host table entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.4.1.1.1 |
mldsHostTableGroupAddressGroup address of IPv6 Host table entry.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.88.4.1.1.2 |
mldsHostTablePortPort number of IPv6 Host table entry.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.88.4.1.1.3 |
mldsHostTableHostIPAddressHost IP address of Group in IPv6 Host table entry.ro Ipv6Address .1.3.6.1.4.1.171.10.76.28.1.88.4.1.1.4 |
companyPPPoE OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.98 |
pppoeGlobalStatePPPoE global staterw Enumeration .1.3.6.1.4.1.171.10.76.28.1.98.1 |
pppoePortTableA table to control PPPoE features of the device. SEQUENCE OF PppoePortEntry .1.3.6.1.4.1.171.10.76.28.1.98.2 |
pppoePortEntryAn entry appears in PPPoE table for each interface
in the system. PppoePortEntry .1.3.6.1.4.1.171.10.76.28.1.98.2.1 |
pppoePortIndexInterface index of the port for the configuration
in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.98.2.1.1 |
pppoePortStatePPPoE per port staterw Enumeration .1.3.6.1.4.1.171.10.76.28.1.98.2.1.2 |
pppoePortCircuitIDTypePPPoE per port circuit ID typerw Enumeration .1.3.6.1.4.1.171.10.76.28.1.98.2.1.3 |
pppoePortUDFStringPPPoE per port UDF stringrw DisplayString .1.3.6.1.4.1.171.10.76.28.1.98.2.1.4 |
pppoePortCircuitIDVendor3StringPPPoE per port circuit ID vendor3 stringrw DisplayString .1.3.6.1.4.1.171.10.76.28.1.98.2.1.5 |
pppoePortRemoteIDTypePPPoE per port remote ID typerw Enumeration .1.3.6.1.4.1.171.10.76.28.1.98.2.1.6 |
pppoePortRemoteIDVendor3StringPPPoE per port remote ID vendor3 stringrw DisplayString .1.3.6.1.4.1.171.10.76.28.1.98.2.1.7 |
companyDoSCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.99 |
doSCtrlTableA table that holds the DoS prevention settings of the device. SEQUENCE OF DoSCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.99.1 |
doSCtrlEntryA list of DoS prevention settings of the device. DoSCtrlEntry .1.3.6.1.4.1.171.10.76.28.1.99.1.1 |
doSCtrlTypeThis object indicates the DoS prevention type.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.99.1.1.1 |
doSCtrlStateThis object indicates the status of the DoS prevention type.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.99.1.1.2 |
doSCtrlActionTypeThis object indicates the action for the DoS prevention type.
If this object is set to 'mirror' and DoSCtrlState is set to 'enable', the configuration
will not take effect until a valid mirror port is specified. If mirror port is not valid
the behavior will be the same as 'drop'rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.99.1.1.3 |
dosCtrlTrapLogStateEnable/Disable Dos Trap Log function.
Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.99.2 |
companyAgentBasicInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.100 |
agentCPUutilization OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.100.1 |
agentCPUutilizationIn5secThe time scale is set at 5 second intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.100.1.1 |
agentCPUutilizationIn1minThe time scale is set at 1 minute intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.100.1.2 |
agentCPUutilizationIn5minThe time scale is set at 5 minute intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.100.1.3 |
agentMEMutilization OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.100.2 |
agentMEMutilizationIn5secThe time scale is set at 5 second intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.100.2.1 |
agentMEMutilizationIn1minThe time scale is set at 1 minute intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.100.2.2 |
agentMEMutilizationIn5minThe time scale is set at 5 minute intervals.
The value will be between 0% (idle) and 100% (very busy).ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.100.2.3 |
companyProtocolVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.101 |
protocolGroupNameTableA table to control protocol group name features of the device. SEQUENCE OF ProtocolGroupNameEntry .1.3.6.1.4.1.171.10.76.28.1.101.1 |
protocolGroupNameEntryAn entry appears in protocol group name table for each interface
in the system. ProtocolGroupNameEntry .1.3.6.1.4.1.171.10.76.28.1.101.1.1 |
protocolGroupGIDThe group ID of protocol group name table.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.101.1.1.1 |
protocolGroupNameThe group name of protocol group name table.rw DisplayString .1.3.6.1.4.1.171.10.76.28.1.101.1.1.2 |
protocolGroupTableA table to control protocol group features of the device. SEQUENCE OF ProtocolGroupEntry .1.3.6.1.4.1.171.10.76.28.1.101.2 |
protocolGroupEntryAn entry appears in protocol group table for each interface
in the system. ProtocolGroupEntry .1.3.6.1.4.1.171.10.76.28.1.101.2.1 |
protocolGroupIdThe group ID of protocol group table.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.101.2.1.1 |
protocolGroupFrameTypeThe frame type of protocol group table.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.101.2.1.2 |
protocolGroupProtocolValueThe protocol value of protocol group table.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.101.2.1.3 |
protocolGroupRowStatusThe row status of protocol group table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.101.2.1.99 |
protocolVlanTableA table to control protocol vlan features of the device. SEQUENCE OF ProtocolVlanEntry .1.3.6.1.4.1.171.10.76.28.1.101.3 |
protocolVlanEntryAn entry appears in protocol vlan table for each interface
in the system. ProtocolVlanEntry .1.3.6.1.4.1.171.10.76.28.1.101.3.1 |
protocolVlanPortThe interface number of protocol vlan table.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.101.3.1.1 |
protocolVlanVIDThe vlan ID of protocol vlan table.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.101.3.1.2 |
protocolVlanGroupIDThe group ID of protocol vlan table.ro Integer32 .1.3.6.1.4.1.171.10.76.28.1.101.3.1.3 |
protocolVlanRowStatusThe row status of protocol vlan table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.101.3.1.99 |
companyL2PT OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.102 |
l2PTStateThis object indicates the global state of Layer 2 protocol tunneling.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.102.1 |
l2PTPortTableA table that cont
ains the cable situation for each port. SEQUENCE OF L2PTEntry .1.3.6.1.4.1.171.10.76.28.1.102.2 |
l2PTEntryA list of cable situations for each port on the device. L2PTEntry .1.3.6.1.4.1.171.10.76.28.1.102.2.1 |
l2PTPortIndexThis object indicates the port number. INTEGER .1.3.6.1.4.1.171.10.76.28.1.102.2.1.1 |
l2PTPortTypeThis object indicates the Layer 2 protocol tunneling port type.
The 'none' value indicates that the port is normal. Layer 2 protocol tunneling
is disabled on this port.
The 'uni' value indicates that the port is connected to the customer site.
A Layer 2 PDU received on a UNI port can be tunneled to a remote customer site across the provider network.
The 'nni' value indicates that the port is connected to the provider network.
A Tunneled Layer 2 PDU received on an NNI port will be restored to its original format.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.102.2.1.2 |
l2PTProtocolThis object indicates the tunneled protocols on this port.
This object can only be applied on a UNI port.
If the 'stp' BIT is set, the STP BPDU will be tunneled.
If the 'gvrp' BIT is set, the GVRP PDU will be tunneled.
If the 'mac-01-00-0C-CC-CC-CC' BIT is set, the PDU with the
destination MAC address 01-00-0C-CC-CC-CC will be tunneled .
If the 'mac-01-00-0C-CC-CC-CD' BIT is set, then the PDU with the
destination MAC address 01-00-0C-CC-CC-CD will be tunneled.rw Bits .1.3.6.1.4.1.171.10.76.28.1.102.2.1.3 |
l2PTThresholdTableThis table contains the protocol tunneling threshold of a UNI port. SEQUENCE OF L2PTThresholdEntry .1.3.6.1.4.1.171.10.76.28.1.102.3 |
l2PTThresholdEntryA list with the Layer2 Protocol tunneling threshold. L2PTThresholdEntry .1.3.6.1.4.1.171.10.76.28.1.102.3.1 |
l2PTProtocolIndexThis object indicates the tunneled protocol of the port. Enumeration .1.3.6.1.4.1.171.10.76.28.1.102.3.1.1 |
l2PTDropThresholdThis object indicates the drop threshold for a given protocol on a UNI port.
If the arrival rate of a tunneled protocol has reached its threshold, the received
PDUs of this protocol will be dropped.
The value 0 indicates there is no threshold for the protocol.rw INTEGER .1.3.6.1.4.1.171.10.76.28.1.102.3.1.2 |
companyQinQ OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.103 |
qinqSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.103.1 |
qinqGlobalStatusThis object is used to enable/disable the Q-in-Q status.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.103.1.1 |
qinqInnerTPIDThis object is used to set the Q-in-Q inner TPID.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.103.1.2 |
qinqTableA table that contains Q-in-Q information about each port. SEQUENCE OF QinQConfigEntry .1.3.6.1.4.1.171.10.76.28.1.103.1.3 |
qinqEntryA list of Q-in-Q information for each port. QinQConfigEntry .1.3.6.1.4.1.171.10.76.28.1.103.1.3.1 |
qinqIfIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.103.1.3.1.1 |
qinqRoleStateSets the QinQ Role as NNI or UNI.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.103.1.3.1.2 |
qinqMissDropStateSets the QinQ Miss Drop state as enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.103.1.3.1.3 |
qinqOuterTPIDSets the QinQ Outer TPID value.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.103.1.3.1.4 |
qinqAddInnerTagStateSets the QinQ Add Inner Tag state as enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.103.1.3.1.5 |
qinqAddInnerTagValueSets the QinQ Add Inner Tag value.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.103.1.3.1.6 |
qinqVLANTranslation OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.103.2 |
qinqVlanTranslationTableA table that contains VLAN translation information. SEQUENCE OF QinQVlanTranslationEntry .1.3.6.1.4.1.171.10.76.28.1.103.2.1 |
qinqVlanTranslationEntryA list of VLAN translation information. QinQVlanTranslationEntry .1.3.6.1.4.1.171.10.76.28.1.103.2.1.1 |
qinqVlanTranslationIfIndexThe interface index.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.76.28.1.103.2.1.1.1 |
qinqVlanTranslationCVIDThe customer VLAN identifier in a C-TAG.ro Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.103.2.1.1.2 |
qinqVlanTranslationSVIDA VLAN identifier conveyed in an S-TAG.rw Unsigned32 .1.3.6.1.4.1.171.10.76.28.1.103.2.1.1.3 |
qinqVlanTranslationPriorityThe priority of TAG.rw Integer32 .1.3.6.1.4.1.171.10.76.28.1.103.2.1.1.4 |
qinqVlanTranslationSVIDOperationThe 'add' action indicates to add a tag for the assigned SP-VLAN
before the C-VLAN tag. If there is S-TAG in the packet, this rule
will not take effect.
The 'replace' action indicates to replace the C-VLAN in the tag by
the SP-VLAN. If there is no C-TAG in the packet, this rule will not
take effect.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.103.2.1.1.5 |
qinqVlanTranslationRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.103.2.1.1.99 |
companySfpVendorInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.104 |
sfpVendorInfoTableThis table indicates the IP address as a destination to forward (relay) DHCP packets to. SEQUENCE OF SfpVendorInfoEntry .1.3.6.1.4.1.171.10.76.28.1.104.1 |
sfpVendorInfoEntryA list of information indicates the IP address as a destination to forward (relay) DHCP packets to. SfpVendorInfoEntry .1.3.6.1.4.1.171.10.76.28.1.104.1.1 |
sfpPortIndexro Integer32 .1.3.6.1.4.1.171.10.76.28.1.104.1.1.1 |
sfpConnectorTypero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.2 |
sfpTranceiverCodero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.3 |
sfpBaudRatero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.4 |
sfpVendorNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.5 |
sfpVendorOuiro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.6 |
sfpVendorPnro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.7 |
sfpVendorRevro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.8 |
sfpWavelengthro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.9 |
sfpVendorSnro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.10 |
sfpDateCodero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.104.1.1.11 |
companyDDM OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.105 |
ddmCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.105.1 |
ddmPowerUnitThis object indicates the TX/RX power global unit.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.105.1.1 |
ddmActionMgmtTableThis table contains the configuration of the action taken
when any parameter exceeds its threshold.obsolete SEQUENCE OF DdmActionMgmtEntry .1.3.6.1.4.1.171.10.76.28.1.105.1.2 |
ddmActionMgmtEntryThis is an entry of the swDdmConfigActionTable.obsolete DdmActionMgmtEntry .1.3.6.1.4.1.171.10.76.28.1.105.1.2.1 |
ddmActionPortThis object indicates the port.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.105.1.2.1.1 |
ddmActionStateThis object indicates the action type.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.105.1.2.1.2 |
ddmActionShutdownThis object indicates the action type.rwobsolete Enumeration .1.3.6.1.4.1.171.10.76.28.1.105.1.2.1.3 |
ddmThresholdMgmtTableThis table contains DDM temperature configuration information. SEQUENCE OF DdmThresholdMgmtEntry .1.3.6.1.4.1.171.10.76.28.1.105.1.3 |
ddmThresholdMgmtEntryThis is an entry of the swDdmConfigThresholdTable. DdmThresholdMgmtEntry .1.3.6.1.4.1.171.10.76.28.1.105.1.3.1 |
ddmThresholdPortThis object indicates the port.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.105.1.3.1.1 |
ddmThresholdTypeThis object indicates the threshold type.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.105.1.3.1.2 |
ddmHighAlarmThis object indicates the high alarm threshold value to be configured. As the
value is a floating point data type, the DisplayString type is used to define this parameter.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.1.3.1.3 |
ddmLowAlarmThis object indicates the low alarm threshold value to be configured. As the
value is a floating data type, the DisplayString type is used to define this parameter.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.1.3.1.4 |
ddmHighWarningThis object indicates the high warning threshold value to be configured. As
the value is a floating data type, the DisplayString type is used to define this parameter.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.1.3.1.5 |
ddmLowWarningThis object indicates the low warning threshold value to be configured. As
the value is a floating data type, the DisplayString type is used to define this parameter.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.1.3.1.6 |
ddmInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.105.2 |
ddmStatus OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.105.2.1 |
ddmStatusTableThis table contains the DDM status information. SEQUENCE OF DdmStatusEntry .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1 |
ddmStatusEntryThis is an entry of the ddmStatusTable. DdmStatusEntry .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1.1 |
ddmStatusPortThis object indicates the port.ro INTEGER .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1.1.1 |
ddmTemperatureThis object indicates the real time value of the temperature. As the value
is a floating point data type, the DisplayString type is used to define this parameter.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1.1.2 |
ddmVoltageThis object indicates the real time value of the supply voltage. As the value
value is a floating point data type, the DisplayString type is used to define this parameter.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1.1.3 |
ddmBiasCurrentThis object indicates the real time value of the tx bias.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1.1.4 |
ddmTxPowerThis object indicates the real time value of the tx power. As the value
is a floating point data type, the DisplayString type is used to define this parameter.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1.1.5 |
ddmRxPowerThis object indicates the real time value of the rx power. As the value is
a floating data type, the DisplayString type is used to define this parameter.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.76.28.1.105.2.1.1.1.6 |
companyCpuProtect OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.76.28.1.106 |
cpuProtectStateThis object indicates the status of the cpu protect.rw Enumeration .1.3.6.1.4.1.171.10.76.28.1.106.1 |
cpuProtectTableA table that holds the cpu protect settings of the device. SEQUENCE OF CpuProtectEntry .1.3.6.1.4.1.171.10.76.28.1.106.2 |
cpuProtectEntryA list of cpu protect settings of the device. CpuProtectEntry .1.3.6.1.4.1.171.10.76.28.1.106.2.1 |
cpuProtectTypeThis object indicates the Cpu protect type.ro Enumeration .1.3.6.1.4.1.171.10.76.28.1.106.2.1.1 |
cpuProtectPPSSpecify the threshold as packet count per second at which traffic is received on the CPU port.
If value set to -1, it means no threshold.rw INTEGER (-1..65535) .1.3.6.1.4.1.171.10.76.28.1.106.2.1.2 |