DES6500-SWL2MGMT-MIB
The Structure of Layer 2 Network Management Information for the D-Link enterprise.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.171.11.78.1.2
137
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
137 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information for the D-Link enterprise. MODULE-IDENTITY .1.3.6.1.4.1.171.11.78.1.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum of the ports within this switch.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.1.1.1 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or the end stations.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.1.1.2 |
swDevInfoBootPromVersionBoot Prom Version.ro DisplayString .1.3.6.1.4.1.171.11.78.1.2.1.1.3 |
swDevInfoFirmwareVersionFirmware Version.ro DisplayString .1.3.6.1.4.1.171.11.78.1.2.1.1.4 |
swDevInfoHardwareVersionHardware Version.ro DisplayString .1.3.6.1.4.1.171.11.78.1.2.1.1.5 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.1.2 |
swL2DevCtrlStpStateThis object can be enabled or disabled spanning tree algorithm during runtime of the system.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.2.1 |
swL2DevCtrlIGMPSnoopingThis object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.2.2 |
swL2DevCtrlIGMPSnoopingMcstRTOnlyrw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.2.3 |
swL2DevCtrlRmonStateThis object can be enabled or disabled RMON.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.2.4 |
swL2DevCtrlCleanAllStatisticCounterAs the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.2.5 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system .rw VlanId .1.3.6.1.4.1.171.11.78.1.2.1.2.6 |
swL2DevCtrlWeb OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.1.2.14 |
swL2DevCtrlWebStateThis object control web status.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.2.14.1 |
swL2DevCtrlWebTcpPortThis object can designate tcp port. When web disable this object can't accessible.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.1.2.14.2 |
swL2DevCtrlTelnet OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.1.2.15 |
swL2DevCtrlTelnetStateThis object control telnet status.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.2.15.1 |
swL2DevCtrlTelnetTcpPortThis object can designate tcp port. When telnet disable this object can't accessible.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.1.2.15.2 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.1.3.3 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.3 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.171.11.78.1.2.3.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .1.3.6.1.4.1.171.11.78.1.2.3.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.3.1.1.1 |
swL2PortInfoPortNumberThis object indicates the module's port number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.78.1.2.3.1.1.2 |
swL2PortInfoUnitIDIndicates ID of the unit in the systemro INTEGER .1.3.6.1.4.1.171.11.78.1.2.3.1.1.3 |
swL2PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.1.1.4 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.1.1.5 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.1.1.6 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.78.1.2.3.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.78.1.2.3.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.3.2.1.1 |
swL2PortCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.78.1.2.3.2.1.2 |
swL2PortCtrlAdminStateThis object decide the port enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.2.1.3 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.2.1.4 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.2.1.5 |
swL2PortCtrlLockStateThis object decide the port is locked or not.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.2.1.6 |
swL2PortCtrlJumboFrameThis object configure the switch's jumbo frame settings.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.3.3 |
swL2QOSMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.6 |
swL2QOSBandwidthControlTable. SEQUENCE OF SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.78.1.2.6.1 |
swL2QOSBandwidthControlEntryA list of information contained in swL2QOSBandwidthControlTable. SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.78.1.2.6.1.1 |
swL2QOSBandwidthPortIndexIndicates the port .ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.1.1.1 |
swL2QOSBandwidthRxRateIndicates RX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.1.1.2 |
swL2QOSBandwidthTxRateIndicates TX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.1.1.3 |
swL2QOSSchedulingTable. SEQUENCE OF SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.78.1.2.6.2 |
swL2QOSSchedulingEntryA list of information contained in swL2QOSSchedulingTable. SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.78.1.2.6.2.1 |
swL2QOSSchedulingClassIndexIndicates the hardware queue number.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.2.1.1 |
swL2QOSSchedulingMaxPktsIndicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.2.1.2 |
swL2QOSSchedulingMechanismIndicates the mechanism of QOS scheduling.ro Enumeration .1.3.6.1.4.1.171.11.78.1.2.6.2.1.3 |
swL2QOS8021pUserPriorityTable. SEQUENCE OF SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.78.1.2.6.3 |
swL2QOS8021pUserPriorityEntryA list of information contained in swL2QOS8021pUserPriorityTable. SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.78.1.2.6.3.1 |
swL2QOS8021pUserPriorityIndexThe 802.1p user priority .ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.3.1.1 |
swL2QOS8021pUserPriorityClassThe number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.3.1.2 |
swL2QOS8021pDefaultPriorityTable. SEQUENCE OF SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.78.1.2.6.4 |
swL2QOS8021pDefaultPriorityEntryA list of information contained in swL2QOS8021pDefaultPriorityTable. SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.78.1.2.6.4.1 |
swL2QOS8021pDefaultPriorityIndexIndicates the port number .ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.4.1.1 |
swL2QOS8021pDefaultPriorityThe priority value to assign to untagged packets received by the switch ports on the switch..rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.6.4.1.2 |
swL2QOSSchedulingMechanismCtrlThis object can control QOS scheduling Mechanism.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.6.5 |
swL2QOSHolPreventionCtrlControl QOS Hol Preventionrw Enumeration .1.3.6.1.4.1.171.11.78.1.2.6.6 |
swL2PortSecurityMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.7 |
swL2PortSecurityControlTableport security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reach N, any coming packet with not learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port. SEQUENCE OF SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.78.1.2.7.1 |
swL2PortSecurityControlEntryA list of information contained in swL2PortSecurityControlTable. SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.78.1.2.7.1.1 |
swL2PortSecurityPortIndexIndicates the secured port to lock address learning.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.7.1.1.1 |
swL2PortSecurityMaxLernAddrIndicates allowable number of addresses to be learned at this port.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.7.1.1.2 |
swL2PortSecurityModeIndicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In deleteOnReset(4) mode - never age out the locked addresses unless restart the system to prevent from port movement or intrusion.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.7.1.1.3 |
swL2PortSecurityAdmStateIndicates administration state of locking address.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.7.1.1.4 |
swL2PortSecurityDelCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.7.2 |
swL2PortSecurityDelVlanNameIndicates vlan name.rw DisplayString .1.3.6.1.4.1.171.11.78.1.2.7.2.1 |
swL2PortSecurityDelPortIndicates the port.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.7.2.2 |
swL2PortSecurityDelMacAddressSpecifies MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.78.1.2.7.2.3 |
swL2PortSecurityDelActivity.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.7.2.4 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.9 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.9.1 |
swL2TrunkCurrentNumEntriesCurrent actived number of entries in the trunk configuration table.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.9.2 |
swL2TrunkCtrlTableThis table specifys which ports group a set of ports(up to 8) into a single logical link. SEQUENCE OF SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.78.1.2.9.3 |
swL2TrunkCtrlEntryA list of information specifies which ports group a set of ports(up to 8) into a single logical link. SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.78.1.2.9.3.1 |
swL2TrunkIndexThe index of logical port trunk. The trunk group number depend on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.9.3.1.1 |
swL2TrunkNameThe name of logical port trunk.rw DisplayString .1.3.6.1.4.1.171.11.78.1.2.9.3.1.2 |
swL2TrunkMasterPortThe object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.9.3.1.3 |
swL2TrunkMemberIndicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one trunks.rw PortList .1.3.6.1.4.1.171.11.78.1.2.9.3.1.4 |
swL2TrunkFloodingPortThe object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.9.3.1.5 |
swL2TrunkTypeThis object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group .rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.9.3.1.6 |
swL2TrunkStateThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.78.1.2.9.3.1.7 |
swL2TrunkAlgorithmThis object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.9.4 |
swL2TrunkLACPPortTableThis table specifys which ports group a set of ports(up to 8) into a single logical link. SEQUENCE OF SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.78.1.2.9.5 |
swL2TrunkLACPPortEntryA list of information specifies which ports group a set of ports(up to 8) into a single logical link. SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.78.1.2.9.5.1 |
swL2TrunkLACPPortIndexThe index of logical port lacp.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.9.5.1.1 |
swL2TrunkLACPPortStateThe state of logical port lacp.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.9.5.1.2 |
swL2MirrorMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.10 |
swL2MirrorLogicTargetPortThis object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.10.1 |
swL2MirrorPortSourceIngressThe represent the ingress into the source port packet to sniffed.rw PortList .1.3.6.1.4.1.171.11.78.1.2.10.2 |
swL2MirrorPortSourceEgressThe represent the egress from the source port packet to sniffed.rw PortList .1.3.6.1.4.1.171.11.78.1.2.10.3 |
swL2MirrorPortStateThis object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.10.4 |
swL2IGMPSnoopingMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.11 |
swL2IGMPSnoopingMaxSupportedVlansMaximum number of Vlans in the layer 2 IGMP control table (swL2IGMPSnoopingCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.1 |
swL2IGMPSnoopingMaxIpGroupNumPerVlanMaximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPSnoopingQueryInfoTable).ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.2 |
swL2IGMPSnoopingCtrlTableThe table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12. SEQUENCE OF SwL2IGMPSnoopingCtrlEntry .1.3.6.1.4.1.171.11.78.1.2.11.3 |
swL2IGMPSnoopingCtrlEntryThe entry in IGMP control table (swL2IGMPSnoopingCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPSnoopingCtrlEntry .1.3.6.1.4.1.171.11.78.1.2.11.3.1 |
swL2IGMPSnoopingCtrlVidThis object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.1 |
swL2IGMPSnoopingQueryIntervalThe frequency at which IGMP Host-Query packets are transmitted on this switch.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.2 |
swL2IGMPSnoopingMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.3 |
swL2IGMPSnoopingRobustnessThe Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.4 |
swL2IGMPSnoopingLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.5 |
swL2IGMPSnoopingHostTimeoutThe timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.6 |
swL2IGMPSnoopingRouteTimeoutThe Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.7 |
swL2IGMPSnoopingLeaveTimerWhen a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.rw INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.3.1.8 |
swL2IGMPSnoopingQueryStateThis object decide the IGMP query enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.11.3.1.9 |
swL2IGMPSnoopingCurrentStateThis object indicates the current IGMP query state.ro Enumeration .1.3.6.1.4.1.171.11.78.1.2.11.3.1.10 |
swL2IGMPSnoopingCtrlStateThis object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry.rw Enumeration .1.3.6.1.4.1.171.11.78.1.2.11.3.1.11 |
swL2IGMPSnoopingQueryInfoTableThe table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device. SEQUENCE OF SwL2IGMPSnoopingQueryInfoEntry .1.3.6.1.4.1.171.11.78.1.2.11.4 |
swL2IGMPSnoopingQueryInfoEntryInformation about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPSnoopingCtrState of associated VLAN entry are all enabled. SwL2IGMPSnoopingQueryInfoEntry .1.3.6.1.4.1.171.11.78.1.2.11.4.1 |
swL2IGMPSnoopingInfoVidThis object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPSnoopingCtrlVid in the associated entry of IGMP control table (swL2IGMPSnoopingCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.4.1.1 |
swL2IGMPSnoopingInfoQueryCountThis object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.4.1.2 |
swL2IGMPSnoopingInfoTxQueryCountThis object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.4.1.3 |
swL2IGMPSnoopingInfoTableThe table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also. SEQUENCE OF SwL2IGMPSnoopingInfoEntry .1.3.6.1.4.1.171.11.78.1.2.11.5 |
swL2IGMPSnoopingInfoEntryInformation about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnoopingSnooping and swL2IGMPSnoopingCtrlState of associated VLAN entry are all enabled. SwL2IGMPSnoopingInfoEntry .1.3.6.1.4.1.171.11.78.1.2.11.5.1 |
swL2IGMPSnoopingVidThis object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.5.1.1 |
swL2IGMPSnoopingGroupIpAddrThis object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.ro IpAddress .1.3.6.1.4.1.171.11.78.1.2.11.5.1.2 |
swL2IGMPSnoopingMacAddrThis object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.78.1.2.11.5.1.3 |
swL2IGMPSnoopingPortMapThis object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.ro PortList .1.3.6.1.4.1.171.11.78.1.2.11.5.1.4 |
swL2IGMPSnoopingIpGroupReportCountThis object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.11.5.1.5 |
swL2TrafficMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.13 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.14 |
swL2TrafficSegTableThis table specifys the port just can forward traffic to the specific port list. SEQUENCE OF SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.78.1.2.14.1 |
swL2TrafficSegEntryA list of information specifies the port with its traffic forward list. SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.78.1.2.14.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .1.3.6.1.4.1.171.11.78.1.2.14.1.1.1 |
swL2TrafficSegForwardPortsThe port list that the specific port can forward traffic.rw PortList .1.3.6.1.4.1.171.11.78.1.2.14.1.1.2 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.15 |
swL2Notify OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.15.1 |
swL2NotifyPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.15.1.2 |
swL2NotifFirmware OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.15.1.2.0 |
swL2RstpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.78.1.2.16 |