DES-1210-52-CX
Detailed view of the defined objects, syntax rules, and hierarchical paths.
866
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
866 total| Object Name |
|---|
dlink OBJECT IDENTIFIER .1.3.6.1.4.1.171 |
dlink_products OBJECT IDENTIFIER .1.3.6.1.4.1.171.10 |
dlink_DES1210SeriesProd OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75 |
des_1210_52 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20 |
des_1210_52_cx OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1 |
companySystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.1 |
sysSwitchNameSystem name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) ' + - = .rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.1.1 |
sysHardwareVersionVersion number of the Hardware.ro DisplayString .1.3.6.1.4.1.171.10.75.20.1.1.2 |
sysFirmwareVersionVersion number of the Firmware.ro DisplayString .1.3.6.1.4.1.171.10.75.20.1.1.3 |
sysLoginTimeoutIntervalThis time interval is used to count the time and logout web interface automatically.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.1.4 |
sysLocationNameThe location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.1.5 |
sysSystemPasswordThis object is used to set System Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.1.7 |
sysSafeGuardEnableThis object is used to set Safeguard Enable\Disable.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.8 |
sysRestartThis object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.1.9 |
sysSaveThis object is used to save Configuration.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.1.10 |
sysJumboFrameEnableGigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 9K bytes (tagged). Default jumbo frame is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.12 |
sysPortCtrlTableA table to control the port specific parameters of the device like speed, duplex mode, etc. SEQUENCE OF SysPortCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.1.13 |
sysPortCtrlEntryAn entry appears in this table for each interface in the system. Index to the table is the interface index of the port. SysPortCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.1.13.1 |
sysPortCtrlIndexInterface index of the port for the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.1.13.1.1 |
sysPortCtrlSpeedConfigures interface speed.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.13.1.2 |
sysPortCtrlOperStatusThe port's operating speed state.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.13.1.3 |
sysPortCtrlMDIConfigures interface auto/mdi/mdix mode. The default setting is Auto.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.13.1.4 |
sysPortCtrlFlowControlEnables / disables flow control for the interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.13.1.5 |
sysPortCtrlFlowControlOperThe link parner negotiate port's operating flow control state.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.13.1.6 |
sysPortCtrlTypeThe port's media type.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.13.1.7 |
sysDhcpAutoConfigurationThis object indicates auto config is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.14 |
sysPortDescriptionTableThe port description table. SEQUENCE OF SysPortDescriptionEntry .1.3.6.1.4.1.171.10.75.20.1.1.16 |
sysPortDescriptionEntryThe port description entry. SysPortDescriptionEntry .1.3.6.1.4.1.171.10.75.20.1.1.16.1 |
sysPortDescIndexThis object indicates the port index.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.1.16.1.1 |
sysPortDescStringThis object indicates the port description.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.1.16.1.2 |
sysDdp OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.1.30 |
sysDdpGlobalOnOffThis object indicates D-Link discover protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.30.1 |
sysDdpGeneralReportOnOffThis object indicates D-Link discover protocol report is enabled or disabled. This object only can be modified when D-Link discover protocol state is enabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.30.2 |
sysDdpGeneralReportTimerThis object indicates D-Link discover protocol report time period. This object only can be modified when both D-Link discover protocol state and D-Link discover protocol report state are enabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.30.3 |
sysDdpProtStatusTableA table to control the port status of D-Link discover protocol. SEQUENCE OF SysDdpProtStatusEntry .1.3.6.1.4.1.171.10.75.20.1.1.30.4 |
sysDdpProtStatusEntryAn entry appears in this table for each port D-Link discover protocol status. SysDdpProtStatusEntry .1.3.6.1.4.1.171.10.75.20.1.1.30.4.1 |
sysDdpProtStatusIndexInterface index of the port for the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.1.30.4.1.1 |
sysDdpProtStatusControlConfigures the port status of D-Link discover protocol.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.1.30.4.1.2 |
sysDhcpRetryTimesThis time for DHCP retried times.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.1.31 |
companyIpifGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.2 |
ipifSupportV4V6Info OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.2.5 |
sysIpAddrCfgModeSpecifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.2.5.1 |
sysIpAddrDefault IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.2.5.2 |
sysIpSubnetMaskIP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.2.5.3 |
sysGatewayGatewayrw IpAddress .1.3.6.1.4.1.171.10.75.20.1.2.5.4 |
ipifNameThe Description for the interface.ro OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.2.5.5 |
ipifv6GlobalStatusThe ID of VLAN that you want this interface to be in. It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.2.5.7 |
ipifv6DHCPStatusThe state of DHCPv6 that you want this interface to be in. It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.2.5.8 |
ipifv6AutolinkloStatusThe global state of link local that you want this interface to be in. It must be a exist vlan id.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.2.5.9 |
ipifv6NSRetransmitTimeThe NS's retransmit time that you want this interface to be in. It must be a exist vlan id.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.2.5.10 |
ipifv6DefaultGatewayThe ipv6 default gateway that you want this interface to be in. To delete gateway, please insert address '0000:0000:0000:0000:0000:0000:0000:0000'.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.2.5.11 |
ipifV6AddressTableA list of interface entries. SEQUENCE OF IpifV6AddressEntry .1.3.6.1.4.1.171.10.75.20.1.2.5.12 |
ipifV6AddressEntryAn entry containing management information applicable to a particular interface. IpifV6AddressEntry .1.3.6.1.4.1.171.10.75.20.1.2.5.12.1 |
ipifV6AddressMainIndexThe index of this IPv6 entry.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.75.20.1.2.5.12.1.1 |
ipifV6AddressIpAddrThe ip address of this IPv6 entry.ro Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.2.5.12.1.2 |
ipifV6AddressIpPrefixThe ip prefix of this IPv6 entry.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.2.5.12.1.3 |
ipifV6AddressIpTypeThe ip type of this IPv6 entry.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.2.5.12.1.4 |
ipifV6AddressRowStatusThe status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.2.5.12.1.5 |
dhcpOption12StatusStatus of DHCP Option12rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.2.6 |
dhcpOption12HostNameHost name in DHCP option 12. The acceptable beginning of DHCP hostname is letter.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.2.7 |
companyTftpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.3 |
tftpFwTargetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.3.9 |
tftpFwTargetServerIpAddressThe TFTP server's IP address is used to upload or download firmware.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.3.9.1 |
tftpFwTargetServerIpTypeType of IP interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.3.9.2 |
tftpFwTargetInterfaceNameSpecifies the interface name when the tftpFwTargetServerIpAddress is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.3.9.3 |
tftpFwTargetImageFileNameConfigure firmware filename to download.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.3.9.4 |
tftpFwTargetTftpOperationThe tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.3.9.5 |
tftpFwTargetTftpOperationStatusThe tftp operation status represent firmware backup or upgrade status.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.3.9.6 |
tftpCfgTargetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.3.10 |
tftpCfgTargetServerIpAddressThe TFTP server's IP address is used to upload or download configuration file.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.3.10.1 |
tftpCfgTargetServerIpTypeType of IP interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.3.10.2 |
tftpCfgTargetInterfaceNameSpecifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.3.10.3 |
tftpCfgTargetImageFileNameThe configuration filename is used to store or retrieve config from the tftp server.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.3.10.4 |
tftpCfgTargetTftpOperationThe tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.3.10.5 |
tftpCfgTargetTftpOperationStatusThe tftp operation status represent configuration file backup or restore status.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.3.10.6 |
companyMiscGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.4 |
miscResetPhysically resets the unit - use with care. A (1) resets the unit, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.4.2 |
miscStatisticsResetResets the units statistics. A (1) resets the statistics count, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.4.3 |
companyRSTP OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.6 |
stpGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.6.1 |
rstpStatusThe administrative module status requested by management for the RSTP Module. This enables or disables RSTP in the system. A value of 'enabled' (1) indicates that RSTP must be enabled in the device on all the ports. A value of 'disabled'(2) indicates that RSTP must be disabled in the device on all the ports.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.6.1.1 |
stpVersionThe version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w. New value may be defined as future versions of the protocol become available.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.6.1.2 |
stpPriorityThe bridge priority vector, as defined in 17.6. The first (RootBridgeID) and third (DesignatedBridgeID)components are both equal to the value of the Bridge Identifier (17.18.2). The other components are zero. Permissible values are 0-61440, in steps of 4096.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.1.3 |
stpTxHoldCountThe value used by the Port Transmit state machine to limit the maximum transmission rate.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.1.4 |
stpProtocolSpecificationAn indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.6.1.5 |
stpTimeSinceTopologyChangeThe time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.10.75.20.1.6.1.6 |
stpTopChangesThe total number of topology changes detected by this bridge since the management entity was last reset or initialized.ro Counter32 .1.3.6.1.4.1.171.10.75.20.1.6.1.7 |
stpDesignatedRootThe bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.ro BridgeId .1.3.6.1.4.1.171.10.75.20.1.6.1.8 |
stpRootCostThe cost of the path to the root as seen from this bridge.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.1.9 |
stpRootPortThe port number of the port which offers the lowest cost path from this bridge to the root bridge.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.1.10 |
stpMaxAgeThe maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. The rootTimes variable comprises the Bridge's operational timer parameter values (Message Age, Max Age, Forward Delay, and Hello Time), derived from the values stored in portTimes (17.19.22) for the Root Port or from BridgeTimes (17.18.4).ro Timeout .1.3.6.1.4.1.171.10.75.20.1.6.1.11 |
stpHelloTimeThe amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. The interval between periodic transmissions of Configuration Messages by Designated Ports (Table 17-1).ro Timeout .1.3.6.1.4.1.171.10.75.20.1.6.1.12 |
stpHoldTimeThis time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.1.13 |
stpForwardDelayThis time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. The delay used by STP Bridges (17.4) to transition Root and Designated Ports to Forwarding (Table 17-1).ro Timeout .1.3.6.1.4.1.171.10.75.20.1.6.1.14 |
stpBridgeMaxAgeThe Max Age component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components the current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero.rw Timeout .1.3.6.1.4.1.171.10.75.20.1.6.1.15 |
stpBridgeHelloTimeThe Hello Time component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components the current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero.rw Timeout .1.3.6.1.4.1.171.10.75.20.1.6.1.16 |
stpBridgeForwardDelayThe Forward Delay component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components the current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero.rw Timeout .1.3.6.1.4.1.171.10.75.20.1.6.1.17 |
stpPortTableA table that contains port-specific information for the Spanning Tree Protocol. SEQUENCE OF StpPortEntry .1.3.6.1.4.1.171.10.75.20.1.6.2 |
stpPortEntryA list of information maintained by every port about the Spanning Tree Protocol state for that port. StpPortEntry .1.3.6.1.4.1.171.10.75.20.1.6.2.1 |
stpPortThe port number of the port for which this entry contains Spanning Tree Protocol management information.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.2.1.1 |
stpPortPriorityThe value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of stpPort.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.2.1.2 |
stpPortStateThe port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see stpPortEnable), this object will have a value of disabled(1).ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.6.2.1.3 |
stpPortEnableThe enabled/disabled status of the port.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.6.2.1.4 |
stpAdminPortPathCostThe contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.2.1.5 |
stpPortPathCostThe contribution of this port to the path cost of paths towards the spanning tree root which include this port.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.2.1.6 |
stpPortDesignatedRootThe unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.ro BridgeId .1.3.6.1.4.1.171.10.75.20.1.6.2.1.7 |
stpPortDesignatedCostThe path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.6.2.1.8 |
stpPortDesignatedBridgeThe Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.ro BridgeId .1.3.6.1.4.1.171.10.75.20.1.6.2.1.9 |
stpPortDesignatedPortThe Port Identifier of the port on the Designated Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.6.2.1.10 |
stpPortForwardTransitionsThe number of times this port has transitioned from the Learning state to the Forwarding state.ro Counter32 .1.3.6.1.4.1.171.10.75.20.1.6.2.1.11 |
stpPortProtocolMigrationWhen operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.6.2.1.12 |
stpPortOperEdgePortThe operational value of the Edge Port parameter. The object is initialized to the value of stpPortAdminEdgePort and is set FALSE on reception of a BPDU.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.6.2.1.13 |
stpPortAdminPointToPointThe administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.6.2.1.14 |
stpPortOperPointToPointThe operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the stpPortAdminPointToPoint object.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.6.2.1.15 |
stpPortEdgeThis parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.6.2.1.16 |
stpPortRestrictedRoleA Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.6.2.1.17 |
stpPortRestrictedTCNA Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC-Operational for the attached LANs transitions frequently.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.6.2.1.18 |
companyDot1qVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.7 |
dot1qVlanManagementOnOffEnable/Disable management VLAN mechanism.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.7.2 |
dot1qVlanManagementidThe management VLAN ID, which will allow to forward packets of that VLAN to CPU.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.7.3 |
dot1qVlanAsyOnOffEnable/Disable IEEE 802.1Q Asymmetric VLANrw Enumeration .1.3.6.1.4.1.171.10.75.20.1.7.5 |
dot1qVlanTableA table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset. SEQUENCE OF Dot1qVlanEntry .1.3.6.1.4.1.171.10.75.20.1.7.6 |
dot1qVlanEntryInformation for a VLAN configured into the device by (local or network) management. Dot1qVlanEntry .1.3.6.1.4.1.171.10.75.20.1.7.6.1 |
dot1qVlanNameAn administratively assigned string, which may be used to identify the VLAN.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.7.6.1.1 |
dot1qVlanEgressPortsThe set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.rw PortList .1.3.6.1.4.1.171.10.75.20.1.7.6.1.2 |
dot1qVlanUntaggedPortsThe set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.rw PortList .1.3.6.1.4.1.171.10.75.20.1.7.6.1.4 |
dot1qVlanRowStatusThe status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.7.6.1.5 |
dot1qVlanPortTableA table containing per port control and status information for VLAN configuration in the device. SEQUENCE OF Dot1qVlanPortEntry .1.3.6.1.4.1.171.10.75.20.1.7.7 |
dot1qVlanPortEntryInformation controlling VLAN configuration for a port on the device. Dot1qVlanPortEntry .1.3.6.1.4.1.171.10.75.20.1.7.7.1 |
dot1qVlanPvidThe PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.rw VlanIndex .1.3.6.1.4.1.171.10.75.20.1.7.7.1.1 |
companyLA OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.8 |
laSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.8.1 |
laStatusSets the Link Aggregation Module administrative status as enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.8.1.2 |
laPortChannelTableA Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel. SEQUENCE OF LaPortChannelEntry .1.3.6.1.4.1.171.10.75.20.1.8.1.3 |
laPortChannelEntryThere is one entry in this table for each created port-channel port. LaPortChannelEntry .1.3.6.1.4.1.171.10.75.20.1.8.1.3.1 |
laPortChannelIfIndexThe index of the port-channel(Aggregator's interface index).ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.75.20.1.8.1.3.1.1 |
laPortChannelMemberListMember Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.rw PortList .1.3.6.1.4.1.171.10.75.20.1.8.1.3.1.2 |
laPortChannelModeCurrent Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.rw PortLaMode .1.3.6.1.4.1.171.10.75.20.1.8.1.3.1.3 |
laPortControl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.8.2 |
laPortControlTableA table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port. SEQUENCE OF LaPortControlEntry .1.3.6.1.4.1.171.10.75.20.1.8.2.1 |
laPortControlEntryA list of Link Aggregation Control configuration parameters for each Aggregation Port on this device. LaPortControlEntry .1.3.6.1.4.1.171.10.75.20.1.8.2.1.1 |
laPortControlIndexThe index of the port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.75.20.1.8.2.1.1.1 |
laPortActorActivityThis object indicates LACP-Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.8.2.1.1.3 |
laPortActorTimeoutThis object indicates LACP-Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.8.2.1.1.4 |
companyStaticMAC OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.9 |
staticDisableAutoLearnSet on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.9.1 |
staticAutoLearningListThe set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable.rw PortList .1.3.6.1.4.1.171.10.75.20.1.9.2 |
staticTableA list of the Static MACs SEQUENCE OF StaticEntry .1.3.6.1.4.1.171.10.75.20.1.9.3 |
staticEntryA Static MAC entry containing the mac and forwarding port. StaticEntry .1.3.6.1.4.1.171.10.75.20.1.9.3.1 |
staticVlanIDThe VLAN ID of the static MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.9.3.1.1 |
staticMacThe MAC address associated of the static MAC entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.9.3.1.2 |
staticPortThe forwarding port of the static MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.9.3.1.3 |
staticStatusThe status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.9.3.1.4 |
companyIgsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.10 |
igsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.10.1 |
igsStatusEnables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.10.1.1 |
igsRouterPortPurgeIntervalThis is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.1.2 |
igsHostPortPurgeIntervalThis is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.1.3 |
igsRobustnessValueWhen the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.1.4 |
igsGrpQueryIntervalThe value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.1.5 |
igsQueryIntervalThis is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.1.6 |
igsQueryMaxResponseTimeThe maximum query response time advertised in IGMPv2 general queries on this interface.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.10.1.7 |
igsReportToAllPortEnables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS module forwards packets to router port only.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.10.1.8 |
igsVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.10.3 |
igsVlanRouterTableThis table contains the list of ports through which a router, in a particular VLAN is reachable. SEQUENCE OF IgsVlanRouterEntry .1.3.6.1.4.1.171.10.75.20.1.10.3.3 |
igsVlanRouterEntryAn igs vlan router entry contain the igs vlan router port list. IgsVlanRouterEntry .1.3.6.1.4.1.171.10.75.20.1.10.3.3.1 |
igsVlanRouterVlanIdIt is the VLAN ID of the igs vlan router entry.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.3.3.1.1 |
igsVlanRouterPortListList of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.ro PortList .1.3.6.1.4.1.171.10.75.20.1.10.3.3.1.2 |
igsVlanFilterTableThis table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. SEQUENCE OF IgsVlanFilterEntry .1.3.6.1.4.1.171.10.75.20.1.10.3.4 |
igsVlanFilterEntryContains snooping status , version and fast leave configuration for a specific VLAN. IgsVlanFilterEntry .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1 |
igsVlanFilterVlanIdIndex of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1.1 |
igsVlanSnoopStatusThis object allows you to enable/disable IGS function on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1.2 |
igsVlanQuerierIndicates whether the switch is configured as a querier in the VLANro Enumeration .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1.3 |
igsVlanCfgQuerierThe snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1.4 |
igsVlanQueryIntervalThis is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1.5 |
igsVlanRtrPortListList of ports which are configured statically as router portsrw PortList .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1.6 |
igsVlanFastLeaveEnables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.10.3.4.1.8 |
igsVlanMulticastGroupTableThis table contains MAC based multicast forwarding information. SEQUENCE OF IgsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.75.20.1.10.3.5 |
igsVlanMulticastGroupEntryThis table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded. IgsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.75.20.1.10.3.5.1 |
igsVlanMulticastGroupVlanIdVLAN ID pertaining to the Multicast forwarding entryro Integer32 .1.3.6.1.4.1.171.10.75.20.1.10.3.5.1.1 |
igsVlanMulticastGroupIpAddressMulticast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.10.75.20.1.10.3.5.1.2 |
igsVlanMulticastGroupMacAddressMulticast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.10.3.5.1.3 |
igsVlanMulticastGroupPortListList of ports onto which the multicast data packets destined for this group will be forwarded.ro PortList .1.3.6.1.4.1.171.10.75.20.1.10.3.5.1.4 |
companyQoSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.12 |
qosModeSettings of Qos mode: IEEE 802.1p QoS or DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.12.1 |
queuingMechanismQueuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS4 spec. Queues with higher weights get bandwidth before than other queues with less weights.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.12.2 |
qosQ1p OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.12.3 |
dot1pPortTableA list of 802.1p port default priority Entries. SEQUENCE OF Dot1pPortEntry .1.3.6.1.4.1.171.10.75.20.1.12.3.1 |
dot1pPortEntryA list of 802.1p port default priority priorities. Dot1pPortEntry .1.3.6.1.4.1.171.10.75.20.1.12.3.1.1 |
dot1pPortIndexA port identifier that is in the range of 1 to ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.3.1.1.1 |
dot1pPortPriorityFor ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, D-Link Smart Switches will refer to their 802.1p information and prioritize them with 8 different priority queues.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.3.1.1.2 |
qosDiffServ OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.12.4 |
qosDiffServEnableDisplay the DSCP(Differentiated services) function Enabled or Disabled. Notice : DiffServ Type is 2~7 bits in the TOS field. ex: If the DiffServ Type = 000011(3), the value in TOS field is 00001100(12)ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.12.4.1 |
qosDiffServTypeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.12.4.2 |
qosDiffServType00DiffServ Type 0 : IP ToS value = 0rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.1 |
qosDiffServType01DiffServ Type 01 : IP ToS value = 4rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.2 |
qosDiffServType02DiffServ Type 02 : IP ToS value = 8rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.3 |
qosDiffServType03DiffServ Type 03 : IP ToS value = 12rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.4 |
qosDiffServType04DiffServ Type 04 : IP ToS value = 16rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.5 |
qosDiffServType05DiffServ Type 05 : IP ToS value = 20rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.6 |
qosDiffServType06DiffServ Type 06 : IP ToS value = 24rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.7 |
qosDiffServType07DiffServ Type 07 : IP ToS value = 28rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.8 |
qosDiffServType08DiffServ Type 08 : IP ToS value = 32rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.9 |
qosDiffServType09DiffServ Type 09 : IP ToS value = 36rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.10 |
qosDiffServType10DiffServ Type 10 : IP ToS value = 40rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.11 |
qosDiffServType11DiffServ Type 11 : IP ToS value = 44rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.12 |
qosDiffServType12DiffServ Type 12 : IP ToS value = 48rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.13 |
qosDiffServType13DiffServ Type 13 : IP ToS value = 52rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.14 |
qosDiffServType14DiffServ Type 14 : IP ToS value = 56rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.15 |
qosDiffServType15DiffServ Type 15 : IP ToS value = 60rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.16 |
qosDiffServType16DiffServ Type 16 : IP ToS value = 64rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.17 |
qosDiffServType17DiffServ Type 17 : IP ToS value = 68rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.18 |
qosDiffServType18DiffServ Type 18 : IP ToS value = 72rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.19 |
qosDiffServType19DiffServ Type 19 : IP ToS value = 76rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.20 |
qosDiffServType20DiffServ Type 20 : IP ToS value = 80rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.21 |
qosDiffServType21DiffServ Type 21 : IP ToS value = 84rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.22 |
qosDiffServType22DiffServ Type 22 : IP ToS value = 88rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.23 |
qosDiffServType23DiffServ Type 23 : IP ToS value = 92rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.24 |
qosDiffServType24DiffServ Type 24 : IP ToS value = 96rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.25 |
qosDiffServType25DiffServ Type 25 : IP ToS value = 100rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.26 |
qosDiffServType26DiffServ Type 26 : IP ToS value = 104rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.27 |
qosDiffServType27DiffServ Type 27 : IP ToS value = 108rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.28 |
qosDiffServType28DiffServ Type 28 : IP ToS value = 112rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.29 |
qosDiffServType29DiffServ Type 29 : IP ToS value = 116rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.30 |
qosDiffServType30DiffServ Type 30 : IP ToS value = 120rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.31 |
qosDiffServType31DiffServ Type 31 : IP ToS value = 124rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.32 |
qosDiffServType32DiffServ Type 32 : IP ToS value = 128rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.33 |
qosDiffServType33DiffServ Type 33 : IP ToS value = 132rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.34 |
qosDiffServType34DiffServ Type 34 : IP ToS value = 136rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.35 |
qosDiffServType35DiffServ Type 35 : IP ToS value = 140rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.36 |
qosDiffServType36DiffServ Type 36 : IP ToS value = 144rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.37 |
qosDiffServType37DiffServ Type 37 : IP ToS value = 148rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.38 |
qosDiffServType38DiffServ Type 38 : IP ToS value = 152rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.39 |
qosDiffServType39DiffServ Type 39 : IP ToS value = 156rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.40 |
qosDiffServType40DiffServ Type 40 : IP ToS value = 160rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.41 |
qosDiffServType41DiffServ Type 41 : IP ToS value = 164rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.42 |
qosDiffServType42DiffServ Type 42 : IP ToS value = 168rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.43 |
qosDiffServType43DiffServ Type 43 : IP ToS value = 172rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.44 |
qosDiffServType44DiffServ Type 44 : IP ToS value = 176rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.45 |
qosDiffServType45DiffServ Type 45 : IP ToS value = 180rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.46 |
qosDiffServType46DiffServ Type 46 : IP ToS value = 184rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.47 |
qosDiffServType47DiffServ Type 47 : IP ToS value = 188rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.48 |
qosDiffServType48DiffServ Type 48 : IP ToS value = 192rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.49 |
qosDiffServType49DiffServ Type 49 : IP ToS value = 196rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.50 |
qosDiffServType50DiffServ Type 50 : IP ToS value = 200rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.51 |
qosDiffServType51DiffServ Type 51 : IP ToS value = 204rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.52 |
qosDiffServType52DiffServ Type 52 : IP ToS value = 208rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.53 |
qosDiffServType53DiffServ Type 53 : IP ToS value = 212rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.54 |
qosDiffServType54DiffServ Type 54 : IP ToS value = 216rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.55 |
qosDiffServType55DiffServ Type 55 : IP ToS value = 220rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.56 |
qosDiffServType56DiffServ Type 56 : IP ToS value = 224rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.57 |
qosDiffServType57DiffServ Type 57 : IP ToS value = 228rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.58 |
qosDiffServType58DiffServ Type 58 : IP ToS value = 232rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.59 |
qosDiffServType59DiffServ Type 59 : IP ToS value = 236rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.60 |
qosDiffServType60DiffServ Type 60 : IP ToS value = 240rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.61 |
qosDiffServType61DiffServ Type 61 : IP ToS value = 244rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.62 |
qosDiffServType62DiffServ Type 62 : IP ToS value = 248rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.63 |
qosDiffServType63DiffServ Type 63 : IP ToS value = 252rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.4.2.64 |
qosTOS OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.12.5 |
qosTOSEnableDisplay the TOS(Type of services) function Enabled or Disabled.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.12.5.1 |
qosTOSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.12.5.2 |
qosTOSType00TOS 0rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.1 |
qosTOSType01TOS 01rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.2 |
qosTOSType02TOS 02rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.3 |
qosTOSType03TOS 03rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.4 |
qosTOSType04TOS 04rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.5 |
qosTOSType05TOS 05rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.6 |
qosTOSType06TOS 06rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.7 |
qosTOSType07TOS 07rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.12.5.2.8 |
companyTrafficMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.13 |
bandwidthCtrlSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.13.1 |
bandwidthCtrlTableA table to control the rate limiting parameters either for the entire switch or for each interface in the switch. SEQUENCE OF BandwidthCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.13.1.2 |
bandwidthCtrlEntryAn entry appears in this table for each physical interface in the switch. BandwidthCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.13.1.2.1 |
bandwidthCtrlIndexThe interface index for which the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.13.1.2.1.1 |
bandwidthCtrlTxThresholdConfigures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port.rw Integer32 (0 | 64..1024000) .1.3.6.1.4.1.171.10.75.20.1.13.1.2.1.2 |
bandwidthCtrlRxThresholdAllows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port.rw Integer32 (0 | 64..1024000) .1.3.6.1.4.1.171.10.75.20.1.13.1.2.1.3 |
broadcastStormCtrlSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.13.3 |
broadcastStormCtrlGlobalOnOffThis object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will allowed you to limit the number of broadcast packets per second going through device.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.13.3.1 |
broadcastStormCtrlLimitTypeThis object indicates storm control function is control broadcast packet or multicast packet or dlf packet.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.13.3.2 |
broadcastStormCtrlThresholdAllows to configure the limiting value for the maximum number of Kbits/sec that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting on this interface. The value that can be set for this object is limited by the underlying hardware. The limit value must be between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port. (Notice : if the limit value is 0, it means unlimited.)rw Integer32 (0 | 64..1024000) .1.3.6.1.4.1.171.10.75.20.1.13.3.3 |
companySecurity OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14 |
securityTrustedHost OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.1 |
trustedHostStatusThis object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.1.1 |
trustedHostTableA table to configure trusted host for in the system. SEQUENCE OF TrustedHostEntry .1.3.6.1.4.1.171.10.75.20.1.14.1.3 |
trustedHostEntryEach entry in this table represents rules for particular trusted host. TrustedHostEntry .1.3.6.1.4.1.171.10.75.20.1.14.1.3.1 |
trustedHostIPTypeType of IP interface.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.1.3.1.1 |
trustedHostIpAddrThe IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.1.3.1.2 |
trustedHostIpMaskUsed to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.1.3.1.3 |
trustedHostRowStatusThe status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. IPv4 Trust Host created example: 1.4.IPv4 address.4.mask IPv6 Trust Host created example: 2.16.IPv6 address.1.prefixrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.1.3.1.4 |
securityPortSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.2 |
portSecTableA table to control port security features of the device. SEQUENCE OF PortSecEntry .1.3.6.1.4.1.171.10.75.20.1.14.2.1 |
portSecEntryAn entry appears in port security table for each interface in the system. PortSecEntry .1.3.6.1.4.1.171.10.75.20.1.14.2.1.1 |
portSecIndexThe interface index for which the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.2.1.1.1 |
portSecStateEnable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.2.1.1.2 |
portSecMLAConfigures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.2.1.1.3 |
securityARPSpoofPrevent OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.3 |
aRPSpoofPreventTableA table to control ARP Spoofing prevention for the entire switch or for each interface in the switch. SEQUENCE OF ARPSpoofPreventEntry .1.3.6.1.4.1.171.10.75.20.1.14.3.1 |
aRPSpoofPreventEntryAn entry appears in this table for each interface in the system. ARPSpoofPreventEntry .1.3.6.1.4.1.171.10.75.20.1.14.3.1.1 |
aRPSpoofPreventIpAddrSpecifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'. IpAddress .1.3.6.1.4.1.171.10.75.20.1.14.3.1.1.1 |
aRPSpoofPreventMacAddressEthernet Mac Address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.3.1.1.2 |
aRPSpoofPreventPortListSpecifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.rw PortList .1.3.6.1.4.1.171.10.75.20.1.14.3.1.1.3 |
aRPSpoofPreventRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.3.1.1.4 |
securitySSL OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.5 |
sslSecurityHttpStatusThis object is for enabling or disabling secure HTTP in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.5.1 |
sslCiphers OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.5.2 |
sslCipherSuiteListThis object is to configure the cipher-suites list.rw Bits .1.3.6.1.4.1.171.10.75.20.1.14.5.2.1 |
securityDhcpServerScreen OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.7 |
dhcpServerScreenEnablePortlistTo enable or disable DHCP Server Screening port list.rw PortList .1.3.6.1.4.1.171.10.75.20.1.14.7.1 |
dhcpServerScreenTrustedServerTableA table that contains the configuration objects for the DHCP server screen server list. An entry appears in this table for each port that may authenticate access to itself. SEQUENCE OF DhcpServerScreenTrustedServerEntry .1.3.6.1.4.1.171.10.75.20.1.14.7.3 |
dhcpServerScreenTrustedServerEntryThe configuration information for an DHCP server screen server. DhcpServerScreenTrustedServerEntry .1.3.6.1.4.1.171.10.75.20.1.14.7.3.1 |
dhcpServerScreenTrustedServerIndexA unique value for DHCP server screen server index. Its value ranges between 1 and 5.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.14.7.3.1.1 |
dhcpServerScreenTrustedServerAddressThe IP address of the DHCP server screen server referred to in this table entry.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.14.7.3.1.2 |
dhcpServerScreenIPTypeType of IP interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.7.3.1.3 |
dhcpServerScreenTrustedServerStatusThe status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The dhcpServerScreenServerIndex objects must be explicitly set.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.7.3.1.4 |
securitySSH OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.8 |
sshSecurityStatusThis object is for enabling or disabling ssh in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.8.1 |
sshMaxAuthFailAttemptsThis object indicates the max auth fail retry attempt times.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.14.8.2 |
sshSessionKeyRekeyingThis object indicates one SSH session rekey time interval.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.8.3 |
sshMaxSessionThis object indicates max SSH session number supported in system.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.14.8.4 |
sshConnectionTimeoutThis object indicates SSH connection timeout value.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.14.8.5 |
sshAuthenMethodPassWordAdminThe object indicates authen method password is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.8.6 |
sshAuthenMethodPubKeyAdminThe object indicates authen method public-key is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.8.7 |
sshAuthenMethodHostKeyAdminThe object indicates authen method host-key is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.8.8 |
sshCipherSuiteListThis object is to configure the cipher-suites list.ro Bits .1.3.6.1.4.1.171.10.75.20.1.14.8.9 |
sshMacSuiteListThis object is to configure the MAC-list.rw Bits .1.3.6.1.4.1.171.10.75.20.1.14.8.10 |
sshPublKeyRSAAdminThe object indicates Public key generating algorithm RSA is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.8.11 |
sshUserInfoTableA table to configure SSH user auth in the system. SEQUENCE OF SshUserInfoEntry .1.3.6.1.4.1.171.10.75.20.1.14.8.12 |
sshUserInfoEntryAn entry to configure user auth in the system. SshUserInfoEntry .1.3.6.1.4.1.171.10.75.20.1.14.8.12.1 |
sshUserInfoIDThe ssh user ID associated with the SSH user Info. entry (ID number of SSH user).ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.8.12.1.1 |
sshUserInfoUserNameThe ssh user name associated with the SSH user Info. entry (e.g., `admin, user').ro DisplayString .1.3.6.1.4.1.171.10.75.20.1.14.8.12.1.2 |
sshUserInfoAuthThe object indicates which auth used by the user.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.8.12.1.3 |
sshUserInfoHostNameThe ssh host name associated with the SSH user Info. entry (e.g., `DUT1, DUT2').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.14.8.12.1.4 |
sshUserInfoHostIpSSH HostBased IP Address of the system. Set '0.0.0.0' to disable SSH hostBased IP address check.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.14.8.12.1.5 |
sshUserInfoHostIpv6SSH HostBased IPv6 Address of the system. Set '0000:0000:0000:0000:0000:0000:0000:0000' or empty string to disable SSH hostBased IPv6 address check.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.14.8.12.1.6 |
securityTrafficSeg OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.9 |
trafficSegStatusEnable/Disable Status of Traffic Segmention.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.9.1 |
trafficSegTableA Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel SEQUENCE OF TrafficSegEntry .1.3.6.1.4.1.171.10.75.20.1.14.9.2 |
trafficSegEntryThere is one entry in this table for each created port-channel port TrafficSegEntry .1.3.6.1.4.1.171.10.75.20.1.14.9.2.1 |
trafficSegIfIndexThe port index of Traffic Segmentation table.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.75.20.1.14.9.2.1.1 |
trafficSegMemberListForwarding member port list of Traffic Segmentation port index.rw PortList .1.3.6.1.4.1.171.10.75.20.1.14.9.2.1.2 |
securityIpMacPortBinding OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.14.10 |
impbSettingTableA table to control IP-MAC-Port Binding Setting features of the device. SEQUENCE OF ImpbSettingEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.1 |
impbSettingEntryAn entry appears in IP-MAC-Port Binding Setting table for each interface in the system. ImpbSettingEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.1.1 |
impbPortIndexSpecifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.14.10.1.1.1 |
impbPortStateDisable / enable IP-MAC-Port Binding admin state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.10.1.1.2 |
impbInsIpPacPortStateEnable / disable IP-MAC-Port Binding also inspect IP packets state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.10.1.1.3 |
impbDHCPPortStateDisable / enable IP-MAC-Port Binding DHCP snooping state for the interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.10.1.1.4 |
impbSmartTableA table to control Smart IP-MAC-Port Binding features of the device. SEQUENCE OF ImpbSmartEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.2 |
impbSmartEntryAn entry appears in Smart IP-MAC-Port Binding table for each interface in the system. ImpbSmartEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.2.1 |
impbSmartMacAddressThe MAC address associated of the smart IP-MAC-PORT Binding entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.10.2.1.1 |
impbSmartPortThe port number of the smart IP-MAC-PORT Binding entry.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.10.2.1.2 |
impbSmartIpAddressThe IP address associated of the smart IP-MAC-PORT Binding entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.10.2.1.3 |
impbSmartVlanIdThe VLAN ID of the smart IP-MAC-PORT Binding entry.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.10.2.1.4 |
impbSmartBindingDisable / enable IP-MAC-Port Binding for the interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.10.2.1.5 |
impbWhiteListTableA table to control Manual IP-MAC-Port Binding white list features of the device. SEQUENCE OF ImpbWhiteListEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.3 |
impbWhiteListEntryAn entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system. ImpbWhiteListEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.3.1 |
impbWhiteListIpAddressThe IP address associated of the Manual IP-MAC-PORT Binding white list entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.10.3.1.1 |
impbWhiteListMacAddressThe MAC address associated of the Manual IP-MAC-PORT Binding white list entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.10.3.1.2 |
impbWhiteListPortThe port number of the Manual IP-MAC-PORT Binding white list entry.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.10.3.1.3 |
impbWhiteListRowStatusThe status of a row in impbWhiteListTable. By setting this object, new entries can be created in impbWhiteListTable and existing entries can be removed from impbWhiteListTable. It can be used as specified in the SNMP v2 standard.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.10.3.1.4 |
impbBlackListTableA table to control IP-MAC-Port Binding black list of the device. SEQUENCE OF ImpbBlackListEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.4 |
impbBlackListEntryAn entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system. ImpbBlackListEntry .1.3.6.1.4.1.171.10.75.20.1.14.10.4.1 |
impbBlackListMacAddressThe MAC address associated of the IP-MAC-PORT Binding black list entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.10.4.1.1 |
impbBlackListVlanIdThe VLAN ID of the IP-MAC-PORT Binding black list entry.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.10.4.1.2 |
impbBlackListPortThe port number of the IP-MAC-PORT Binding black list entry.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.14.10.4.1.3 |
impbBlackListIpAddressThe IP address associated of the IP-MAC-PORT Binding black list entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.14.10.4.1.4 |
impbBlackListStatusnothing/delete IP-MAC-Port Binding for the interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.10.4.1.5 |
impbAutoScanIpAddressFromThe begin for IP address associated of the IP-MAC-PORT Binding auto scan entry.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.14.10.5 |
impbAutoScanIpAddressToThe end for IP address associated of the IP-MAC-PORT Binding auto scan entry.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.14.10.6 |
impbAutoScanStatusNothing / scan IP-MAC-Port Binding auto scan for the interface.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.14.10.7 |
companyACLGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15 |
aclProfile OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15.1 |
aclProfileTableA table to ACL profile . SEQUENCE OF AclProfileEntry .1.3.6.1.4.1.171.10.75.20.1.15.1.1 |
aclProfileEntryEach entry in this table is a ACL profile. Index to the table is ACL profile ID. AclProfileEntry .1.3.6.1.4.1.171.10.75.20.1.15.1.1.1 |
aclProfileNoThe ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.1.1.1.1 |
aclProfileNameAn administratively assigned string, which may be used to identify the Profile.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.15.1.1.1.2 |
aclProfileTypeThe ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3v4 (2) - for IPv4-based rule, l3v4Ext (3) - for IPv4-Ext rule, l3v6 (4) - for IPv6-based rule. Note that only l2, l3 and l3v6 could be set by user, other is reserved for system to show information.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.1.1.1.3 |
aclProfileRuleCountThe number of rules in this profile.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.1.1.1.4 |
aclProfileStatusThis object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.1.1.1.14 |
aclL2Rule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15.2 |
aclL2RuleTableA table to configure L2 filter rules in the system. SEQUENCE OF AclL2RuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.2.1 |
aclL2RuleEntryEach entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID. AclL2RuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1 |
aclL2AccessIDL2 Filter rule ID.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.1 |
aclL2ProfileIDACL Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.2 |
aclL2RuleEtherTypeThe value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition. The aclL2EtherFrameType should be specified as ether-type.rw Integer32 (-1 | 1501..65535) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.3 |
aclL2RuleDstMacAddrDestination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.4 |
aclL2RuleSrcMacAddrSource MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. addressrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.5 |
aclL2RuleVlanIdVlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.rw Integer32 (-1..4094) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.6 |
aclL2Rule1pPriority802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.rw Integer32 (-1..7) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.7 |
aclL2RuleDstMacAddrMaskThe MAC address Mask work for Destination MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.8 |
aclL2RuleSrcMacAddrMaskThe MAC address Mask work for Source MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.9 |
aclL2RuleActionSpecifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.10 |
aclL2RulePriorityEnter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition.rw INTEGER (-1..7) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.12 |
aclL2RuleReplacePriorityEnable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.13 |
aclL2RuleStatusThis object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.2.1.1.99 |
aclL3v4Rule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15.3 |
aclL3v4RuleTableA table to configure L3 filter rules in the system. SEQUENCE OF AclL3v4RuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.3.1 |
aclL3v4RuleEntryEach entry in this table is a L3 filter rule. Index to the table is L3 filter number. AclL3v4RuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1 |
aclL3v4RuleAccessIDL3 Filter rule ID.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.1 |
aclL3v4RuleProfileNoThe Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.2 |
aclL3v4RuleDstIpAddrDestination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.3 |
aclL3v4RuleSrcIpAddrSource IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.4 |
aclL3v4RuleDstIpAddrMaskThe IP subnet mask for Destination IP address.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.5 |
aclL3v4RuleSrcIpAddrMaskThe IP subnet mask for Source IP address.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.6 |
aclL3v4RuleActionSpecifies the action to be taken on the packet if the filter rule matches.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.7 |
aclL3v4RulePriorityEnter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition.rw INTEGER (-1..7) .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.9 |
aclL3v4RuleReplacePriorityEnable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.10 |
aclL3v4RuleStatusThis object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.3.1.1.99 |
aclL3v4ExtRule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15.4 |
aclL3v4ExtRuleTableA table to configure L3 filter rules in the system. SEQUENCE OF AclL3v4ExtRuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.4.1 |
aclL3v4ExtRuleEntryEach entry in this table is a L3 filter rule. Index to the table is L3 filter number. AclL3v4ExtRuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1 |
aclL3v4ExtRuleAccessIDL3 Filter rule ID.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.1 |
aclL3v4ExtRuleProfileNoThe Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.2 |
aclL3v4ExtRuleProtocolThe type of protocol to be checked against the packet.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.3 |
aclL3v4ExtRuleICMPMessageTypeThe message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.4 |
aclL3v4ExtRuleICMPMessageCodeThe message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.5 |
aclL3v4ExtRuleDstIpAddrDestination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.6 |
aclL3v4ExtRuleSrcIpAddrSource IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.7 |
aclL3v4ExtRuleDstIpAddrMaskThe IP subnet mask for Destination IP address.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.8 |
aclL3v4ExtRuleSrcIpAddrMaskThe IP subnet mask for Source IP address.rw IpAddress .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.9 |
aclL3v4ExtRuleTcpUdpDstPortThe TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.10 |
aclL3v4ExtRuleTcpUdpSrcPortThe TCP / UDP source port. The default value is -1, which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.11 |
aclL3v4ExtRuleTcpUdpDstPortMaskThe TCP / UDP Destination port Mask.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.12 |
aclL3v4ExtRuleTcpUdpSrcPortMaskThe TCP / UDP Source port Mask.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.13 |
aclL3v4ExtRuleDscpThe IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. The aclL3RuleTos should be specified as dscp.rw Integer32 (-1..63) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.20 |
aclL3v4ExtRuleToSThe ToS value to be checked against the packet. A default value is '-1', which means the rule don't care this condition. The cmAclL3RuleTos should be specified as dscp.rw Integer32 (-1..15) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.21 |
aclL3v4ExtRuleIgmpTypeThe IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.22 |
aclL3v4ExtRuleProtocolIdSpecifies the protocol id. The aclL3RuleProtocol should be specified as protocol-id.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.26 |
aclL3v4ExtRuleActionSpecifies the action to be taken on the packet if the filter rule matches.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.31 |
aclL3v4ExtRulePriorityEnter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition.rw INTEGER (-1..7) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.33 |
aclL3v4ExtRuleReplacePriorityEnable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.34 |
aclL3v4ExtRuleStatusThis object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.4.1.1.99 |
aclL3v6Rule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15.5 |
aclL3v6RuleTableA table to configure L3 ipv6 filter rules in the system. SEQUENCE OF AclL3v6RuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.5.1 |
aclL3v6RuleEntryEach entry in this table is a L3 ipv6 filter rule. Index to the table is L3 ipv6 filter number. AclL3v6RuleEntry .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1 |
aclL3v6RuleAccessIDL3 Filter rule ID.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.1 |
aclL3v6RuleProfileNoThe Profile ID which this rule join.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.2 |
aclL3v6RuleTrafficClassThe Traffic Class value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.3 |
aclL3v6RuleProtocolThe type of protocol to be checked against the packet.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.4 |
aclL3v6RuleProtocolIdSpecifies the protocol id. The aclL3v6RuleProtocol should be specified as protocol-id.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.5 |
aclL3v6RuleTcpUdpDstPortThe TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.6 |
aclL3v6RuleTcpUdpSrcPortThe TCP / UDP source port. The default value is -1, which means the rule don't care this condition.rw Integer32 (-1..65535) .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.7 |
aclL3v6RuleTcpUdpDstPortMaskThe TCP / UDP Destination port Mask.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.8 |
aclL3v6RuleTcpUdpSrcPortMaskThe TCP / UDP Source port Mask.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.9 |
aclL3v6RuleICMPv6MessageTypeThe message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.10 |
aclL3v6RuleICMPv6MessageCodeThe message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),rw Integer32 (-1..255) .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.11 |
aclL3v6RuleDstIpv6AddrDestination IPv6 address to be matched with the packet.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.12 |
aclL3v6RuleSrcIpv6AddrSource IPv6 address to be matched with the packet.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.13 |
aclL3v6RuleDstIpv6AddrPrefixLenThe prefix length for Destination IPv6 address.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.14 |
aclL3v6RuleSrcIpv6AddrPrefixLenThe prefix length for Source IPv6 address.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.15 |
aclL3v6RuleActionSpecifies the action to be taken on the packet if the filter rule matches.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.90 |
aclL3v6RulePriorityEnter a priority value if you want to re-write the 802.1p user priority of a packet to the value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue.By Default, the value will be '-1', which means the rule don't care this condition.rw INTEGER (-1..7) .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.92 |
aclL3v6RuleReplacePriorityEnable this option and manually enter the replacement value used to re-write the 802.1p user priority value entered in the Priority field, which meets the criteria specified previously in this command, before forwarding it on to the specified CoS queue. Otherwise, a packet will have its incoming 802.1p user priority re-written to its original value before being forwarded by the Switch.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.93 |
aclL3v6RuleStatusThis object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.5.1.1.99 |
aclPortBindGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15.6 |
aclPortGroupTableA table to control the port group binding information of L2 Group, L3v4 Group, and L3v6 Group SEQUENCE OF AclPortGroupEntry .1.3.6.1.4.1.171.10.75.20.1.15.6.1 |
aclPortGroupEntryAn entry appears in this table for each interface in the system. Index to the table is the interface index of the port. AclPortGroupEntry .1.3.6.1.4.1.171.10.75.20.1.15.6.1.1 |
aclPortIndexInterface index of the port for the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.6.1.1.1 |
aclPortL2ProfileNoThe L2 Profile ID which this port bind. zero means not configured.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.6.1.1.2 |
aclPortL3v4ProfileNoThe L3v4 Profile ID which this port bind. zero means not configured.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.6.1.1.3 |
aclPortL3v6ProfileNoThe L3v6 Profile ID which this port bind. zero means not configured.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.6.1.1.4 |
aclHWResourceStatus OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.15.8 |
aclHWResourceStatusTableA table to display HW Resource Status. SEQUENCE OF AclHWResourceStatusEntry .1.3.6.1.4.1.171.10.75.20.1.15.8.1 |
aclHWResourceStatusEntryAn entry appears in this table for each interface in the system. Index to the table is the HW profile index of the ACL. AclHWResourceStatusEntry .1.3.6.1.4.1.171.10.75.20.1.15.8.1.1 |
aclHWProfileIndexHW profile index of the ACL for the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.8.1.1.1 |
aclAccessListNoThe profile name in this HW profile index.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.15.8.1.1.2 |
aclResourceEntryCountThe number of entries in this HW profile index.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.15.8.1.1.3 |
companySyslog OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.16 |
syslogGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.16.2 |
syslogStateThis object is for enabling or disabling syslog alert features in the system. System Logs record and manage events, as well as report errors and informational messages.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.16.2.1 |
syslogTimeStampOptionThis object is for enabling or disabling timestamp option. When enabled, the messages (log and email alert messages) will hold the time stamp information. When disabled, the time stamp information will not be carried with the messages sent to the log and mail servers.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.16.2.2 |
syslogSrvSeveritySpecifies the log level option to be set for a specific module.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.16.2.3 |
syslogSrvFacilityThe Syslog standard facilities. The facility to be used when sending Syslog messages to this server.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.16.2.4 |
syslogSrvTableA table containing entries of priority,server address type, server address, port through which it can send and tranport type. SEQUENCE OF SyslogSrvEntry .1.3.6.1.4.1.171.10.75.20.1.16.2.5 |
syslogSrvEntryA table containing index as priority , server address type and server address. SyslogSrvEntry .1.3.6.1.4.1.171.10.75.20.1.16.2.5.1 |
syslogSrvIPTypeSpecifies the Address type of server.Address type shall be ipv4 or ipv6.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.16.2.5.1.1 |
syslogSrvIPSpecifies the ServerIP to which the syslog shall be forwarded.ro Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.16.2.5.1.2 |
syslogSrvPortSpecifies the Port through which it can send the syslog message. By default the the port is 514rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.16.2.5.1.3 |
syslogInterfaceNameSpecifies the interface name when the syslogSrvIP is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.16.2.5.1.4 |
syslogSrvRowStatusThe Status of the Server Entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.16.2.5.1.5 |
companyLBD OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.17 |
sysLBDStateEnableEnable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.17.1 |
sysLBDModeLoopback detection function mode.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.17.2 |
sysLBDIntervalSet a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.17.3 |
sysLBDRecoverTimeThis time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.rw Integer32 (0 | 60..1000000) .1.3.6.1.4.1.171.10.75.20.1.17.4 |
sysLBDCtrlTableA table to control Loopback detection features either for the entire switch or for each interface in the switch. SEQUENCE OF SysLBDCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.17.5 |
sysLBDCtrlEntryAn entry appears in this table for each interface in the system. SysLBDCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.17.5.1 |
sysLBDCtrlIndexThe interface index of the port for which the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.17.5.1.1 |
sysLBDPortStatusProvides control to per port enable or disable the loopback detection function. Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.17.5.1.2 |
sysLBDPortLoopStatusThe loop status for this port.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.17.5.1.3 |
sysLBDVlanLoopTableA table to display Loopback detection features by vlan mode . SEQUENCE OF SysLBDVlanLoopEntry .1.3.6.1.4.1.171.10.75.20.1.17.6 |
sysLBDVlanLoopEntryAn entry appears in this table for each interface in the system. SysLBDVlanLoopEntry .1.3.6.1.4.1.171.10.75.20.1.17.6.1 |
sysLBDVlanLoopIndexDisplay port lists loop status by vlan.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.17.6.1.1 |
sysLBDVlanLoopPortsDisplay port lists loop status by vlan.ro PortList .1.3.6.1.4.1.171.10.75.20.1.17.6.1.2 |
swLoopDetectEnabledVlanListThis object indicates the VLANs that enabled LBD. Note: For the LBD enabled VLAN specification, the value should be separated by ',' or '-'. Such as: 1,4,7 or 1,4,7-9 .rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.17.7 |
companyMirror OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.18 |
sysMirrorStatusEnable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.18.1 |
sysMirrorTargetPortSpecifies the port to which the mirrored traffic in the system is to be copied.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.18.2 |
sysMirrorCtrlIngressMirroringProvides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.rw PortList .1.3.6.1.4.1.171.10.75.20.1.18.3 |
sysMirrorCtrlEgressMirroringProvides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.rw PortList .1.3.6.1.4.1.171.10.75.20.1.18.4 |
companySNTPSetting OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.20 |
sysSNTPServerTable OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.20.17 |
sysSNTPTimeSecondsThis object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037).rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.20.17.1 |
sysSNTPFirstServerSNTP First Server's IPv6 Addressrw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.20.17.2 |
sysSNTPFirstTypeSNTP First Server's IPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.20.17.3 |
sysSNTPFirstInterfaceNameSpecifies the interface name when the sysSNTPFirstServer is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.20.17.4 |
sysSNTPSecondServerSNTP Second Server's IPv6 Addressrw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.20.17.5 |
sysSNTPSecondTypeSNTP First Server's IPv6 Address type.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.20.17.6 |
sysSNTPSecondInterfaceNameSpecifies the interface name when the sysSNTPSecondServer is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.20.17.7 |
sysSNTPPollIntervalSNTP Poll Interval In Seconds (30-99999)rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.20.17.8 |
sysSNTPStateEnable/Disable SNTP function in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.20.17.9 |
sysSNTPDSTOffsetThis object is for Daylight Saving Time Offset In (30/60/90/120) Minutes.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.20.17.10 |
sysSNTPGMTMinutesSpecifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.11 |
sysSNTPDSTStartMonThe start month of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.12 |
sysSNTPDSTStartDayThe start day of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.13 |
sysSNTPDSTStartHourThe start hour of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.14 |
sysSNTPDSTStartMinThe start minute of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.15 |
sysSNTPDSTEndMonThe end month of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.16 |
sysSNTPDSTEndDayThe end day of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.17 |
sysSNTPDSTEndHourThe end hour of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.18 |
sysSNTPDSTEndMinThe end minute of Daylight Saving Time.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.20.17.19 |
sysSNTPDSTStateThis object is for Annual(1) or Disabled(2) DST state in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.20.17.20 |
companyVoiceVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.21 |
voicevlanSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.21.1 |
voiceVlanModeVoice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. This object is for enabling or disabling Voice Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Voice VLAN can not be enabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.21.1.2 |
voiceVlanIdThe ID of VLAN that you want the voice traffic to be in. It must be a exist vlan id.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.21.1.3 |
voiceVlanTimeoutA period of time in hour to remove a port from voice VLAN if the port is an automatic VLAN member. The Timeout range is 1~120 hours. Default aging time is 1 hour.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.21.1.4 |
voiceVlanPriorityThe 802.1p priority levels of the traffic in the Voice VLAN.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.21.1.5 |
voicevlanPortControlTableA table that contains Voice Vlan Port Control configuration information. SEQUENCE OF VoiceVlanPortControlEntry .1.3.6.1.4.1.171.10.75.20.1.21.1.6 |
voicevlanPortControlEntryA list of Voice Vlan Control configuration parameters for each Port on this device. VoiceVlanPortControlEntry .1.3.6.1.4.1.171.10.75.20.1.21.1.6.1 |
voicevlanPortControlIndexThe voice vlan port index.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.10.75.20.1.21.1.6.1.1 |
voicevlanPortAutoDetectionThis object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN automatically if it detects the device OUI matches the Telephony OUI. If the port is a static member of voice vlan or a LA member, it can not enable voice vlan auto detection.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.21.1.6.1.2 |
voicevlanPortManuTagModeUser assign per port tag/untag mode.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.21.1.6.1.3 |
voicevlanPortCurrentTagModePer port current tag/untag mode.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.21.1.6.1.4 |
voicevlanPortStateThis object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan. none - this port is not a member of voice vlan.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.21.1.6.1.5 |
voicevlanOUI OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.21.2 |
voicevlanOUITableA voice vlan OUI entry containing the description and mac. SEQUENCE OF VoicevlanOUIEntry .1.3.6.1.4.1.171.10.75.20.1.21.2.1 |
voicevlanOUIEntryA voice vlan OUI entry containing the description and mac. VoicevlanOUIEntry .1.3.6.1.4.1.171.10.75.20.1.21.2.1.1 |
voicevlanOUITelephonyOUIAn Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's OUI that user created.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.21.2.1.1.1 |
voicevlanOUIDescriptionThe Description for the OUI.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.21.2.1.1.2 |
voicevlanOUIMaskVoice vlan OUI Mask. Always be FF:FF:FF:00:00:00.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.21.2.1.1.3 |
voicevlanOUIStatusThis object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.21.2.1.1.4 |
voicevlanDevice OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.21.3 |
voicevlanDeviceTableA voice vlan Device entry containing the description and mac. SEQUENCE OF VoicevlanDeviceEntry .1.3.6.1.4.1.171.10.75.20.1.21.3.1 |
voicevlanDeviceEntryA voice vlan Device entry containing the description and mac. VoicevlanDeviceEntry .1.3.6.1.4.1.171.10.75.20.1.21.3.1.1 |
voicevlanDeviceIndexMacAn Mac Address is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's Mac that voice device created.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.21.3.1.1.1 |
voicevlanDevicePortThe port is learning by voice device.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.21.3.1.1.2 |
voicevlanDevicePriorityThe priority value for voice device.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.21.3.1.1.3 |
voicevlanDeviceTagTypeThe tag type for voice device.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.21.3.1.1.4 |
voicevlanDeviceStatusThis object indicates the status of this entry. You can delete this object.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.21.3.1.1.5 |
companyAuthGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.23 |
swAuthenCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.23.1 |
swAuthStatusEnable/Disable Static 802.1x.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.1.1 |
authProtocolThe authentication method used to authenticate users.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.1.3 |
swAuthCtrlPktFwdModeEnable/Disable 802.1x packet forward while 802.1x module is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.1.4 |
swAuthPortAccessCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.23.2 |
swAuthPortAccessControlTableA table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself. SEQUENCE OF SwAuthPortAccessControlEntry .1.3.6.1.4.1.171.10.75.20.1.23.2.1 |
swAuthPortAccessControlEntryThe configuration information for an Authenticator Port. SwAuthPortAccessControlEntry .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1 |
swAuthAuthConfigPortNumberA unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.1 |
swAuthAuthQuietPeriodThe value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.2 |
swAuthAuthSuppTimeoutThe value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.3 |
swAuthAuthServerTimeoutThe value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.4 |
swAuthAuthMaxReqThe value of the maxReq constant currently in use by the Backend Authentication state machine.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.5 |
swAuthAuthTxPeriodThe value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.6 |
swAuthAuthReAuthPeriodThe value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.7 |
swAuthAuthReAuthenticationThe enable/disable control used by the Reauthentication Timer state machine (8.5.5.1).rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.8 |
swAuthAuthConfigPortControlThe current value of the controlled Port control parameter for the Port.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.9 |
swAuthAuthCapabilityThe current value of the controlled Port control parameter for the Port.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.10 |
swAuthAuthDirectionThe current value of the controlled Port control parameter for the Port.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.2.1.1.11 |
swAuthUser OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.23.3 |
swAuthUserTableA table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself. SEQUENCE OF SwAuthUserEntry .1.3.6.1.4.1.171.10.75.20.1.23.3.1 |
swAuthUserEntryThe configuration information for an Authenticator Port. SwAuthUserEntry .1.3.6.1.4.1.171.10.75.20.1.23.3.1.1 |
swAuthUserNameThe unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.ro SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.23.3.1.1.1 |
swAuthUserPasswordThis object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.23.3.1.1.2 |
swAuthUserStatusThe status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.23.3.1.1.3 |
swAuthRadiusServer OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.23.4 |
swAuthRadiusServerTableA table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself. SEQUENCE OF SwAuthRadiusServerEntry .1.3.6.1.4.1.171.10.75.20.1.23.4.2 |
swAuthRadiusServerEntryThe configuration information for an Authenticator Port. SwAuthRadiusServerEntry .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1 |
swAuthRadiusServerIndexA unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.1 |
swAuthRadiusIPTypeThe IP address of the RADIUS server IP type referred to in this table entry.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.2 |
swAuthRadiusServerAddressThe IP address of the RADIUS server referred to in this table entry.rw Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.3 |
swAuthRadiusServerInterfaceNameSpecifies the interface name when the swAuthRadiusServerAddress is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.4 |
swAuthRadiusServerAuthenticationPortThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.5 |
swAuthRadiusServerAccountingPortThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.6 |
swAuthRadiusServerTimeoutThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.7 |
swAuthRadiusServerRetransmitThe value is for setting UDP Port.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.8 |
swAuthRadiusServerKeyThis object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.9 |
swAuthRadiusServerStatusThe status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.23.4.2.1.10 |
companyLLDPSetting OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.24 |
dlinklldpStateThis object is used for enabling or disabling LLDP in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.24.1 |
dlinklldpMsgHoldMultiplierThe time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.24.2 |
dlinklldpMsgTxIntervalThis object is used for LLDP packet update frequency. The timer in units of seconds.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.24.3 |
dlinklldpReinitDelayThis object is used for LLDP Reinitialization Delay. The timer in units of seconds.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.24.4 |
dlinklldpTxDelayThe lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval).rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.24.5 |
dlinklldpConfigManAddrTableThe table that controls selection of LLDP management address TLV instances to be transmitted on individual ports. SEQUENCE OF DlinklldpConfigManAddrEntry .1.3.6.1.4.1.171.10.75.20.1.24.7 |
dlinklldpConfigManAddrEntryLLDP configuration information that specifies the set of ports (represented as a PortList) on which the local system management address instance will be transmitted. This configuration object augments the lldpLocManAddrEntry, therefore it is only present along with the management address instance contained in the associated lldpLocManAddrEntry entry. Each active lldpConfigManAddrEntry must be restored from non-volatile and re-created (along with the corresponding lldpLocManAddrEntry) after a re-initialization of the management system. DlinklldpConfigManAddrEntry .1.3.6.1.4.1.171.10.75.20.1.24.7.1 |
dlinklldpLocManAddrSubtypeThe type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object.ro AddressFamilyNumbers (IANA-ADDRESS-FAMILY-NUMBERS-MIB) .1.3.6.1.4.1.171.10.75.20.1.24.7.1.1 |
dlinklldpLocManAddrThe string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity.ro LldpManAddress .1.3.6.1.4.1.171.10.75.20.1.24.7.1.2 |
dlinklldpConfigManAddrPortsTxEnableA set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will be transmitted on the member ports of the lldpManAddrPortsTxEnable. The default value for lldpConfigManAddrPortsTxEnable object is empty binary string, which means no ports are specified for advertising indicated management address instance.rw PortList .1.3.6.1.4.1.171.10.75.20.1.24.7.1.3 |
companySNMPV3 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25 |
snmpGlobalStateThis object is for enabling or disabling SNMP Community function.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.1 |
snmpV3User OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25.2 |
snmpV3UserTable SEQUENCE OF SnmpV3UserEntry .1.3.6.1.4.1.171.10.75.20.1.25.2.1 |
snmpV3UserEntry SnmpV3UserEntry .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1 |
snmpV3UserNameA human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.ro SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.1 |
snmpV3UserVersionA human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.2 |
snmpV3UserGroupNameThe name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.3 |
snmpV3UserAuthProtocolAn indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.4 |
snmpV3UserAuthProtocolPasswordrw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.5 |
snmpV3UserPrivProtocolAn indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.6 |
snmpV3UserPrivProtocolPasswordrw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.7 |
snmpV3UserStatusThe status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.25.2.1.1.8 |
snmpV3Group OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25.3 |
snmpV3GroupTable SEQUENCE OF SnmpV3GroupEntry .1.3.6.1.4.1.171.10.75.20.1.25.3.1 |
snmpV3GroupEntry SnmpV3GroupEntry .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1 |
snmpV3GroupNameThe name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.ro SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1.1 |
snmpV3GroupSecurityModelIn order to gain the access rights allowed by this conceptual row, this securityModel must be in use.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1.2 |
snmpV3GroupSecurityLevelThe minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected.ro SnmpSecurityLevel (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1.3 |
snmpV3GroupReadViewNameThe value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1.4 |
snmpV3GroupWriteViewNameThe value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1.5 |
snmpV3GroupNotifyViewNameThe value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1.6 |
snmpV3GroupStatusThe status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.25.3.1.1.7 |
snmpV3ViewTree OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25.4 |
snmpV3ViewTreeTable SEQUENCE OF SnmpV3ViewTreeEntry .1.3.6.1.4.1.171.10.75.20.1.25.4.1 |
snmpV3ViewTreeEntry SnmpV3ViewTreeEntry .1.3.6.1.4.1.171.10.75.20.1.25.4.1.1 |
snmpV3viewTreeNameThe human readable name for a family of view subtrees.ro SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.4.1.1.1 |
snmpV3viewTreeSubtreeThe MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.ro OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25.4.1.1.2 |
snmpV3viewTreeMaskThe bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.25.4.1.1.3 |
snmpV3viewTreeTypeIndicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.4.1.1.4 |
snmpV3viewTreeStatusThe status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.25.4.1.1.5 |
snmpV3Community OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25.5 |
snmpV3CommunityTable SEQUENCE OF SnmpV3CommunityEntry .1.3.6.1.4.1.171.10.75.20.1.25.5.1 |
snmpV3CommunityEntry SnmpV3CommunityEntry .1.3.6.1.4.1.171.10.75.20.1.25.5.1.1 |
snmpV3CommunityNameThe unique index value of a row in this table.ro OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.25.5.1.1.1 |
snmpV3CommunityPolicyA human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.5.1.1.2 |
snmpV3CommunityStatusThe status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.25.5.1.1.3 |
snmpV3Host OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25.6 |
snmpV3HostTable SEQUENCE OF SnmpV3HostEntry .1.3.6.1.4.1.171.10.75.20.1.25.6.2 |
snmpV3HostEntry SnmpV3HostEntry .1.3.6.1.4.1.171.10.75.20.1.25.6.2.1 |
snmpV3HostAddressThis object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.ro Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.25.6.2.1.1 |
snmpV3IPTypeType of IP interface.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.6.2.1.2 |
snmpV3HostCommunityNameThe locally arbitrary.rw SnmpAdminString .1.3.6.1.4.1.171.10.75.20.1.25.6.2.1.3 |
snmpV3HostVersionThe Level of Security to be used when generating SNMP messages using this entry.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.6.2.1.4 |
snmpV3HostInterfaceNameSpecifies the interface name when the syslogSrvIP is linklocal address.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.25.6.2.1.5 |
snmpV3HostStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.25.6.2.1.6 |
snmpV3EngineIDAn SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.rw SnmpEngineID (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.171.10.75.20.1.25.7 |
snmpV3Trap OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.25.8 |
snmpV3TrapSNMPAuthenticationThis object is for enabling or disabling SNMP login fail event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.8.1 |
snmpV3TrapBootupThis object is for enabling or disabling devie Bootup event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.8.2 |
snmpV3TrapPortLinkUpDownThis object is for enabling or disabling Port link up / link down event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.8.3 |
snmpV3TrapRSTPStateChangeThis object is for enabling or disabling RSTP topology change event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.8.4 |
snmpV3TrapFirmUpgradeThis object is for enabling or disabling Firmware upgrade suess or fail event trap in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.8.5 |
snmpV3TrapLBDrw Enumeration .1.3.6.1.4.1.171.10.75.20.1.25.8.11 |
companyAutoSurveillanceVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.26 |
autoSurveillanceVlanSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.26.1 |
autoSurveillanceVlanModeThis object is for enabling or disabling Auto Surveillance Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Auto Surveillance VLAN can not be enabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.26.1.1 |
autoSurveillanceVlanIdThe ID of VLAN that you want the surveillance traffic to be in. It must be a exist vlan id.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.26.1.2 |
autoSurveillanceVlanPriorityThe 802.1p priority levels of the traffic in the Auto Surveillance VLAN.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.26.1.3 |
autoSurveillanceVlanTaggedUplinkDownlinkPortAuto Surveillance vlan uplink ports can't auto learning OUI.rw PortList .1.3.6.1.4.1.171.10.75.20.1.26.1.4 |
autoSurveillanceVlanOUI OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.26.2 |
autoSurveillanceVlanOUITableA Auto Surveillance vlan OUI entry containing the description and mac. SEQUENCE OF AutoSurveillanceVlanOUIEntry .1.3.6.1.4.1.171.10.75.20.1.26.2.1 |
autoSurveillanceVlanOUIEntryA Auto Surveillance vlan OUI entry containing the description and mac. AutoSurveillanceVlanOUIEntry .1.3.6.1.4.1.171.10.75.20.1.26.2.1.1 |
autoSurveillanceVlanOUISurveillanceOUIAn Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the surveillance traffic's OUI that user created.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.26.2.1.1.1 |
autoSurveillanceVlanOUIDescriptionThe Description for the OUI.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.26.2.1.1.2 |
autoSurveillanceVlanOUIMaskAuto Surveillance vlan OUI Mask. The default OUI Mask is FF:FF:FF:F0:00:00. And default OUI Mask is read-only. In user define OUI's Mask is FF:FF:FF:00:00:00, in user define MAC's Mask is FF:FF:FF:FF:FF:FF.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.26.2.1.1.3 |
autoSurveillanceVlanOUIComponentTypeThis object indicates the Component Type of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIComponentType to be CreateAndGo, then this entry will turn to be Active.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.26.2.1.1.4 |
autoSurveillanceVlanOUIStatusThis object indicates the status of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.26.2.1.1.5 |
companyTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.27 |
traps OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.27.0 |
topologyChangeAST-TOPOLOGY-CHG-TRAP-VAL. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.75.20.1.27.0.4 |
firmwareUpgradeSuccessSNMP-FIRMUPGRADE-SUCC. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.75.20.1.27.0.8 |
firmwareUpgradeFailureSNMP-FIRMUPGRADE-FAIL. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.75.20.1.27.0.9 |
firmwareIllegalFileSNMP-FIRMUPGRADE-FAIL2. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.75.20.1.27.0.10 |
firmwareTransferErrorSNMP-FIRMUPGRADE-FAIL1. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.75.20.1.27.0.11 |
firmwareChecksumErrorSNMP-FIRMUPGRADE-FAIL3. NOTIFICATION-TYPE .1.3.6.1.4.1.171.10.75.20.1.27.0.12 |
companyMulticastFilter OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.28 |
mcastFilterPortTableA table to control multicast filtering modes. SEQUENCE OF McastFilterPortEntry .1.3.6.1.4.1.171.10.75.20.1.28.1 |
mcastFilterPortEntryAn entry appears in this table for each interface in the mcastFiltertem. Index to the table is the interface index of the port. McastFilterPortEntry .1.3.6.1.4.1.171.10.75.20.1.28.1.1 |
mcastFilterPortIndexInterface index of the port for which the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.28.1.1.1 |
mcastFilterPortTypeConfigures the multicast filtering modes as below : forward - This will instruct the Switch to forward a multicast packet whose destination is an unregistered multicast group residing within the range of ports specified above. filter - This will instruct the Switch to filter any multicast packets whose destination is an unregistered multicast group residing within the range of ports specified above.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.28.1.1.2 |
companyGreenSetting OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.31 |
dlinkGreenLEDShutoff OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.31.1 |
dlinkGreenLEDShutoffPortListProvides control to disable LED port.rw PortList .1.3.6.1.4.1.171.10.75.20.1.31.1.1 |
dlinkGreenLEDShutoffStateEnable/Disable Green disable LED function. Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.31.1.2 |
dlinkGreenLEDShutoffTimeProfile1The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.31.1.3 |
dlinkGreenLEDShutoffTimeProfile2The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.31.1.4 |
dlinkGreenPortShutoff OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.31.2 |
dlinkGreenPortShutoffPortListProvides control to disable LED port.rw PortList .1.3.6.1.4.1.171.10.75.20.1.31.2.1 |
dlinkGreenPortShutoffStateEnable/Disable Green disable LED function. Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.31.2.2 |
dlinkGreenPortShutoffTimeProfile1The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.31.2.3 |
dlinkGreenPortShutoffTimeProfile2The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.31.2.4 |
dlinkGreenSystemHibernation OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.31.4 |
dlinkGreenSystemHibernationStateEnable/Disable Green disable LED function. Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.31.4.1 |
dlinkGreenSystemHibernationTimeProfile1The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.31.4.2 |
dlinkGreenSystemHibernationTimeProfile2The time profile name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.31.4.3 |
dlinkPowerSavingGlobalSettingEnable/Disable Power Saving global setting. Default is disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.31.6 |
companyTimeRangeMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.32 |
swTimeRangeSettingTableA table to configure time Range in the system. SEQUENCE OF SwTimeRangeSettingEntry .1.3.6.1.4.1.171.10.75.20.1.32.1 |
swTimeRangeSettingEntryA schedule entry to configure time Range in the system. SwTimeRangeSettingEntry .1.3.6.1.4.1.171.10.75.20.1.32.1.1 |
swTimeRangeIndexThe Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.32.1.1.1 |
swTimeRangeNameThe Schedule name associated with the Schedule entry (e.g., `abc, bbb').rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.32.1.1.2 |
swTimeRangeDateEnable/Disable date range checking while executing time base PoE.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.3 |
swTimeRangeStartYearStart year of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.4 |
swTimeRangeStartMonthStart month of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.5 |
swTimeRangeStartDayStart day of the Schedule entry. The value must be from 1 to 31.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.32.1.1.6 |
swTimeRangeStartHourStart hour of the Schedule entry. The value must be from 0 to 23.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.32.1.1.7 |
swTimeRangeStartMinuteStart minute of the Schedule entry. The value must be from 0 to 59.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.32.1.1.8 |
swTimeRangeEndYearEnd year of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.9 |
swTimeRangeEndMonthEnd month of the Schedule entry.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.10 |
swTimeRangeEndDayEnd day of the Schedule entry. The value must be from 1 to 31.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.32.1.1.11 |
swTimeRangeEndHourEnd hour of the Schedule entry. The value must be from 0 to 23.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.32.1.1.12 |
swTimeRangeEndMinuteEnd minute of the Schedule entry. The value must be from 0 to 59.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.32.1.1.13 |
swTimeRangeMondayEnable/Disble scheduling Monday.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.14 |
swTimeRangeTuesdayEnable/Disble scheduling Tuesday.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.15 |
swTimeRangeWednesdayEnable/Disble scheduling Wednesday.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.16 |
swTimeRangeThursdayEnable/Disble scheduling Thursday.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.17 |
swTimeRangeFridayEnable/Disble scheduling Friday.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.18 |
swTimeRangeSaturdayEnable/Disble scheduling Saturday.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.19 |
swTimeRangeSundayEnable/Disble scheduling Sunday.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.32.1.1.20 |
swTimeRangeRowStatusThe status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.32.1.1.21 |
companyStaticMcast OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.35 |
staticMcastTableA list of the Static MACs SEQUENCE OF StaticMcastEntry .1.3.6.1.4.1.171.10.75.20.1.35.1 |
staticMcastEntryA Static MAC entry containing the mac and forwarding port. StaticMcastEntry .1.3.6.1.4.1.171.10.75.20.1.35.1.1 |
staticMcastVlanIDThe VLAN ID of the static MAC entry.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.35.1.1.1 |
staticMcastMacThe MAC address associated of the static MAC entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.35.1.1.2 |
staticMcastEgressPortsThe set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.ro PortList .1.3.6.1.4.1.171.10.75.20.1.35.1.1.3 |
staticMcastStatusThe status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.35.1.1.4 |
companyCableDiagnostic OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.37 |
cableDiagTriggerIndexTrigger an interface index to do cable diagnostic.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.37.1 |
cableDiagPair1TestResultCable diagnostics pair 1 test result.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.37.2 |
cableDiagPair1FaultDistanceCable Diagnostics pair 1 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.37.3 |
cableDiagPair2TestResultCable diagnostics pair 2 test result.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.37.4 |
cableDiagPair2FaultDistanceCable diagnostics pair 2 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.37.5 |
cableDiagPair3TestResultCable diagnostics pair 3 test result.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.37.6 |
cableDiagPair3FaultDistanceCable diagnostics pair 3 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.37.7 |
cableDiagPair4TestResultCable diagnostics pair 4 test result.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.37.8 |
cableDiagPair4FaultDistanceCable diagnostics pair 4 fault distance.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.37.9 |
cableDiagLengthinRangeCable diagnostics length when link up in speed 1G. (Display in range)ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.37.10 |
companyRMON OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47 |
rmonGlobalStateThis object is for enabling or disabling RMON function.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.47.1 |
rmonStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47.2 |
rmonStatsTableA list of Ethernet statistics entries. SEQUENCE OF RmonStatsEntry .1.3.6.1.4.1.171.10.75.20.1.47.2.1 |
rmonStatsEntryA collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1 RmonStatsEntry .1.3.6.1.4.1.171.10.75.20.1.47.2.1.1 |
rmonStatsIndexThe value of this object uniquely identifies this etherStats entry.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.2.1.1.1 |
rmonStatsDataSourceThis object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1).rw OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47.2.1.1.2 |
rmonStatsOwnerThe entity that configured this entry and is therefore using the resources assigned to it.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.47.2.1.1.3 |
rmonStatsStatusThe status of this etherStats entry.rw RmonStatus .1.3.6.1.4.1.171.10.75.20.1.47.2.1.1.4 |
rmonHistory OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47.3 |
rmonHistoryTableA list of history control entries. SEQUENCE OF RmonHistoryEntry .1.3.6.1.4.1.171.10.75.20.1.47.3.1 |
rmonHistoryEntryA list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2 RmonHistoryEntry .1.3.6.1.4.1.171.10.75.20.1.47.3.1.1 |
rmonHistoryIndexAn index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.3.1.1.1 |
rmonHistoryDataSourceThis object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).rw OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47.3.1.1.2 |
rmonHistoryBucketsRequestedThe requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.3.1.1.3 |
rmonHistoryIntervalThe interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.3.1.1.4 |
rmonHistoryOwnerThe entity that configured this entry and is therefore using the resources assigned to it.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.47.3.1.1.5 |
rmonHistoryStatusThe status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).rw RmonStatus .1.3.6.1.4.1.171.10.75.20.1.47.3.1.1.6 |
rmonAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47.4 |
rmonAlarmTableA list of alarm entries. SEQUENCE OF RmonAlarmEntry .1.3.6.1.4.1.171.10.75.20.1.47.4.1 |
rmonAlarmEntryA list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8 RmonAlarmEntry .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1 |
rmonAlarmIndexAn index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.1 |
rmonAlarmIntervalThe interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1).rw Integer32 UNITS "Seconds" .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.2 |
rmonAlarmVariableThe object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1).rw OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.3 |
rmonAlarmSampleTypeThe method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1).rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.4 |
rmonAlarmRisingThresholdA threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.5 |
rmonAlarmFallingThresholdA threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.6 |
rmonAlarmRisingEventIndexThe index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.7 |
rmonAlarmFallingEventIndexThe index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.8 |
rmonAlarmOwnerThe entity that configured this entry and is therefore using the resources assigned to it.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.9 |
rmonAlarmStatusThe status of this alarm entry.rw RmonStatus .1.3.6.1.4.1.171.10.75.20.1.47.4.1.1.10 |
rmonEvent OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.47.5 |
rmonEventTableA list of events to be generated. SEQUENCE OF RmonEventEntry .1.3.6.1.4.1.171.10.75.20.1.47.5.1 |
rmonEventEntryA set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6 RmonEventEntry .1.3.6.1.4.1.171.10.75.20.1.47.5.1.1 |
rmonEventIndexAn index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.47.5.1.1.1 |
rmonEventDescriptionA comment describing this event entry.rw DisplayString .1.3.6.1.4.1.171.10.75.20.1.47.5.1.1.2 |
rmonEventTypeThe type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.47.5.1.1.3 |
rmonEventCommunityIf an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string.rw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.47.5.1.1.4 |
rmonEventOwnerThe entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this devicerw OCTET STRING .1.3.6.1.4.1.171.10.75.20.1.47.5.1.1.5 |
rmonEventStatusThe status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent.rw RmonStatus .1.3.6.1.4.1.171.10.75.20.1.47.5.1.1.6 |
companyNeighbor OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.50 |
neighborTableA list of the Neighbor Cache Table. SEQUENCE OF NeighborEntry .1.3.6.1.4.1.171.10.75.20.1.50.1 |
neighborEntryA Neighbor cache entry containing the ifindex and ipv6 addr. NeighborEntry .1.3.6.1.4.1.171.10.75.20.1.50.1.1 |
neighborIfindexThe interface index of the Neighbor entry.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.50.1.1.1 |
neighborIPv6AddrAllows the entry of an IP address that will be a Neighbor entry into the Neighbor Cache Table.ro Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.50.1.1.2 |
neighborMACAddrThe MAC address associated of the Neighbor entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.50.1.1.3 |
neighborTypeThe type associated of the Neighbor entry.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.50.1.1.4 |
neighborCacheStateThe type associated of the Neighbor entry.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.50.1.1.5 |
neighborRowStatusThe status of an entry in the Neighbor Cache Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.50.1.1.7 |
companydot3azEEE OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.52 |
dot3azEEEset OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.52.1 |
dot3azTableA table to control IEEE802.3az EEE settings features of the device. SEQUENCE OF Dot3azEntry .1.3.6.1.4.1.171.10.75.20.1.52.1.1 |
dot3azEntryAn entry appears in IEEE802.3az EEE table for each interface in the system. Dot3azEntry .1.3.6.1.4.1.171.10.75.20.1.52.1.1.1 |
portD3IndexThe interface index for which the configuration in this entry applies.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.52.1.1.1.1 |
portD3StateEnable / disable port IEEE802.3az EEE admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.52.1.1.1.2 |
companyDHCPRelay OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.61 |
dhcpRelayControl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.61.1 |
dhcpRelayStateThis object indicates DHCP relay function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.61.1.1 |
dhcpRelayHopCountThis object indicates the maximum number of router hops that the packets can cross.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.61.1.2 |
dhcpRelayTimeThresholdThis object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.61.1.3 |
dhcpRelayManagement OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.61.2 |
dhcpRelayInterfaceSettingsTableThis table indicates the IP address as a destination to forward (relay) DHCP packets to. SEQUENCE OF DhcpRelayInterfaceSettingsEntry .1.3.6.1.4.1.171.10.75.20.1.61.2.1 |
dhcpRelayInterfaceSettingsEntryA list of information indicates the IP address as a destination to forward (relay) DHCP packets to. DhcpRelayInterfaceSettingsEntry .1.3.6.1.4.1.171.10.75.20.1.61.2.1.1 |
dhcpRelayInterfaceThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.10.75.20.1.61.2.1.1.1 |
dhcpRelayServerIPThis object indicates the DHCP server IP address.ro IpAddress .1.3.6.1.4.1.171.10.75.20.1.61.2.1.1.2 |
dhcpRelayInterfaceSettingsRowStatusThis object indicates the status of this entry. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.61.2.1.1.3 |
dhcpRelayManagementOption82 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.61.2.2 |
dhcpRelayOption82StateThis object indicates DHCP relay option 82 function always enabled.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.61.2.2.1 |
dhcpRelayOption82CheckStateThis object indicates DHCP relay option 82 Check function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.61.2.2.2 |
dhcpRelayOption82PolicyThis object indicates DHCP relay option 82 policy.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.61.2.2.3 |
dhcpRelayOption82RemoteIDTypeThis object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.61.2.2.4 |
dhcpRelayOption82RemoteIDThis object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swDHCPRelayOption82RemoteIDType is set to user-defined, a new value can be written to this object.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.61.2.2.5 |
companyDHCPLocalRelay OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.62 |
dhcpLocalRelayGlobalStateThis object indicates DHCP local relay function of VLAN is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.62.1 |
dhcpLocalRelayTableThis table indicates the IP address as a destination to forward (local relay) DHCP packets to. SEQUENCE OF DhcpLocalRelayEntry .1.3.6.1.4.1.171.10.75.20.1.62.2 |
dhcpLocalRelayEntryA list of information indicates the IP address as a destination to forward (local relay) DHCP packets to. DhcpLocalRelayEntry .1.3.6.1.4.1.171.10.75.20.1.62.2.1 |
dhcpLocalRelaySettingsVLANIDThis object displays the current VLAN ID of the device.ro INTEGER .1.3.6.1.4.1.171.10.75.20.1.62.2.1.1 |
dhcpLocalRelaySettingsStateThis object indicates DHCP local relay function of VLAN is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.62.2.1.2 |
companyDHCPv6Relay OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.63 |
dhcpv6RelayControl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.63.1 |
dhcpv6RelayStateThis object indicates DHCPv6 relay function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.63.1.1 |
dhcpv6RelayHopCountThis object indicates the maximum number of router hops that the DHCPv6 packets can cross.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.63.1.2 |
dhcpv6RelayManagement OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.63.2 |
dhcpv6RelayInterfaceSettingsTableThis table indicates the IP address as a destination to forward (relay) DHCP packets to. SEQUENCE OF Dhcpv6RelayInterfaceSettingsEntry .1.3.6.1.4.1.171.10.75.20.1.63.2.1 |
dhcpv6RelayInterfaceSettingsEntryA list of information indicates the IP address as a destination to forward (relay) DHCP packets to. Dhcpv6RelayInterfaceSettingsEntry .1.3.6.1.4.1.171.10.75.20.1.63.2.1.1 |
dhcpv6RelayInterfaceThis object indicates the maximum number of router hops that the DHCPv6 packets can cross.ro DisplayString .1.3.6.1.4.1.171.10.75.20.1.63.2.1.1.1 |
dhcpv6RelayServerIPThis object indicates the DHCP server IP address.ro Ipv6Address .1.3.6.1.4.1.171.10.75.20.1.63.2.1.1.2 |
dhcpv6RelayInterfaceSettingsRowStatusThis object indicates the status of this entry. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.63.2.1.1.99 |
dhcpv6RelayOption37 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.63.3 |
dhcpv6RelayOption37StateThis object indicates DHCPv6 relay option 37 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.63.3.1 |
dhcpv6RelayOption37CheckStateThis object indicates DHCPv6 relay option 37 Check function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.63.3.2 |
dhcpv6RelayOption37RemoteIDTypeThis object indicates the type of remote ID.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.63.3.3 |
dhcpv6RelayOption37RemoteIDThis object displays the current remote ID of the device. If RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If RemoteIDType is set to user-defined, a new value can be written to this object.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.63.3.4 |
companyMldsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.88 |
mldsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.88.1 |
mldsStatusEnables or disables MLD snooping in the system. When set to 'enabled', the MLDS module starts protocol operations. When set to 'disabled', the MLDS module stops performing protocol operations.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.88.1.1 |
mldsRouterPortPurgeIntervalThis is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.1.2 |
mldsHostPortPurgeIntervalThis is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.1.3 |
mldsRobustnessValueWhen the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'mldsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.1.4 |
mldsGrpQueryIntervalThe value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'mldsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.1.5 |
mldsQueryIntervalThis is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs.rw Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.1.6 |
mldsQueryMaxResponseTimeThe maximum query response time advertised in MLDv1 general queries on this interface.rw INTEGER .1.3.6.1.4.1.171.10.75.20.1.88.1.7 |
mldsVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.88.3 |
mldsVlanRouterTableThis table contains the list of ports through which a router, in a particular VLAN is reachable. SEQUENCE OF MldsVlanRouterEntry .1.3.6.1.4.1.171.10.75.20.1.88.3.3 |
mldsVlanRouterEntryContains the VLAN ID and list of ports on which routers are present in the VLAN. MldsVlanRouterEntry .1.3.6.1.4.1.171.10.75.20.1.88.3.3.1 |
mldsVlanRouterVlanIdVLAN ID of the ports through which router is reachable.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.3.3.1.1 |
mldsVlanRouterPortListList of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.ro PortList .1.3.6.1.4.1.171.10.75.20.1.88.3.3.1.2 |
mldsVlanFilterTableThis table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system. SEQUENCE OF MldsVlanFilterEntry .1.3.6.1.4.1.171.10.75.20.1.88.3.4 |
mldsVlanFilterEntryContains snooping status , version and fast leave configuration for a specific VLAN. MldsVlanFilterEntry .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1 |
mldsVlanFilterVlanIdIndex of MldsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in MldsVlanFilterEntry is to be done.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1.1 |
mldsVlanSnoopStatusThis object allows you to enable/disable MLDS function on a specific VLAN.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1.2 |
mldsVlanQuerierIndicates whether the switch is configured as a querier in the VLANro Enumeration .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1.3 |
mldsVlanCfgQuerierThe snooping switch can be configured as a querier via this object to send out MLD general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1.4 |
mldsVlanQueryIntervalThis is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.ro Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1.5 |
mldsVlanRtrPortListList of ports which are configured statically as router portsrw PortList .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1.6 |
mldsVlanFastLeaveEnables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.88.3.4.1.8 |
mldsVlanMulticastGroupTableThis table contains MAC based multicast forwarding information. SEQUENCE OF MldsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.75.20.1.88.3.5 |
mldsVlanMulticastGroupEntryThis table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded. MldsVlanMulticastGroupEntry .1.3.6.1.4.1.171.10.75.20.1.88.3.5.1 |
mldsVlanMulticastGroupVlanIdVLAN ID pertaining to the Multicast forwarding entryro Integer32 .1.3.6.1.4.1.171.10.75.20.1.88.3.5.1.1 |
mldsVlanMulticastGroupIpAddressMulticast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.171.10.75.20.1.88.3.5.1.2 |
mldsVlanMulticastGroupMacAddressMulticast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.20.1.88.3.5.1.3 |
mldsVlanMulticastGroupPortListList of ports onto which the multicast data packets destined for this group will be forwarded.ro PortList .1.3.6.1.4.1.171.10.75.20.1.88.3.5.1.4 |
companyDoSCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.20.1.99 |
doSCtrlStateThis object indicates the status of the DoS prevention type.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.99.1 |
doSCtrlTableA table that holds the DoS prevention settings of the device. SEQUENCE OF DoSCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.99.2 |
doSCtrlEntryA list of DoS prevention settings of the device. DoSCtrlEntry .1.3.6.1.4.1.171.10.75.20.1.99.2.1 |
doSCtrlTypeThis object indicates the DoS prevention type.ro Enumeration .1.3.6.1.4.1.171.10.75.20.1.99.2.1.1 |
doSCtrlDisplayStateThis object indicates the status of the DoS prevention type.rw Enumeration .1.3.6.1.4.1.171.10.75.20.1.99.2.1.2 |