CONFIG-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CONFIG-MIB.
255
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
255 total| Object Name |
|---|
hpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7 |
RFC1155-SMI Unknown .1.3.6.1.4.1.25506.11.1.7 |
hpSwitchConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1 |
hpSwitchTraps OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.0 |
hpSwitchStpErrantBpduReceivedThis trap indicates that unexpected (errant) STP BPDU
has been received on a port (e.g. on a port that is
connected to non-STP device). This notification trap
is controlled by the state of 'hpSwitchStpTrapCntl'
object. Implementation of this trap is optional. TRAP-TYPE .1.3.6.1.4.1.25506.11.1.7.1.0.0.1 |
hpSwitchTrapsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.0.1 |
hpSwitchStpErrantBpduDetectorThe identifier of the feature generating Errant
BPDU trap.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.0.1.1 |
hpSwitchStpErrantBpduSrcMacThe source MAC address of the port sending Errant
STP BPDU.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.0.1.2 |
hpSwitchSystemConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.1 |
hpSwitchAutoRebootIf the value of this variable was set to yes(1),
booting will conditionally enable all application
modules-the spanning tree, IP and IPX etc.. Otherwise
every application module must be manually enabled
through Network Control Language Interpreter's ENABLE
command.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.1.1 |
hpSwitchTimeZoneThe number of minutes to the east of Greenwich Mean
Time(GMT). For a location west of GMT, use a negative
integer.rw INTEGER (-720..840) .1.3.6.1.4.1.25506.11.1.7.1.1.2 |
hpSwitchDaylightTimeRuleThe daylight savings time rule for use by the
Internet's RFC 868 Time protocol.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.1.3 |
hpSwitchDaylightBeginningMonthThe month that daylight saving time starts if
DaylightTimeRule is set to userDefined.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.1.4 |
hpSwitchDaylightBeginningDayThe day of the month that daylight saving time
starts if DaylightTimeRule is set to userDefined.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.1.5 |
hpSwitchDaylightEndingMonthThe month that daylight saving time ends if
DaylightTimeRule is set to userDefined.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.1.6 |
hpSwitchDaylightEndingDayThe day of the month that daylight saving time emds
if DaylightTimeRule is set to userDefined.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.1.7 |
hpSwitchSystemConfigStatusThe configuration status of this group of objects.
If one or more variables in this group were
reconfigurated since last reboot and required reboot
to take effect, the value of this variable will be
set to notInService.ro ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.1.8 |
hpSwitchSystemPortLEDModeThe mode of the port LED can be either link/activity
(link for 3 seconds then activity thereafter) or
link-only.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.1.9 |
hpSwitchControlUnknownIPMulticastWhen enabled along with IGMP, any IP Multicast packets
that are not already controlled by IGMP will be
restricted to ports that have detected a multicast
router or ports configured to always forward IP
multicast. When set to disabled or when IGMP is
disabled, the unknown IP Multicast packets will be
flooded out all ports in the VLANrw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.1.10 |
hpSwitchIgmpDelayedGroupFlushTimerThis feature is disabled by default, which is indicated
by a timer value of 0 seconds. When IGMP is enabled and
the value of the Delayed Group Flush Timer is not zero,
traffic filters for any previously-joined IGMP groups
which no longer have active members will persist for
the number of seconds indicated by the timer. This has
the effect of dropping any additional unjoined traffic
for an empty group until the Delayed Group Flush Timer
expires, at which time the traffic filter is then
removed.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.1.11 |
hpSwitchMaxFrameSizeThis is the value of the global jumbos max-frame-size
supported by the switch. The default value for this is
set to 9216, in order to make it compatible with
previous versions of software. This configuration does
not take a reboot to take effect.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.1.12 |
hpSwitchIpMTUThis is the value of the global jumbos IP MTU or L3 MTU
supported by the switch. The default value for this is
set to 9198, in order to make it compatible with
previous versions of software. This configuration does
not take a reboot to take effect.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.1.13 |
hpSwitchConsoleConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.2 |
hpSwitchTelnetAdminStatusThe status of the console telnet operation.rwobsolete Enumeration .1.3.6.1.4.1.25506.11.1.7.1.2.1 |
hpSwitchTerminalTypeTerminal type of the console device.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.2.2 |
hpSwitchConsoleRefRateThe rate, in second per cycle, at which the display
of various switch measurements.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.2.3 |
hpSwitchDisplayedEventThe type of event messages are automatically
displayed on the console.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.2.4 |
hpSwitchConsoleConfigStatusThe configuration status of this group of objects.
If one or more variables in this group were
reconfigurated since last reboot and required reboot
to take effect, the value of this variable will be
set to notInService.ro ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.2.5 |
hpSwitchPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.3 |
hpSwitchPortTableA table that contains information about the current
port status in this device. SEQUENCE OF HpSwitchPortEntry .1.3.6.1.4.1.25506.11.1.7.1.3.1 |
hpSwitchPortEntryInformation about a specific port status in this
device. HpSwitchPortEntry .1.3.6.1.4.1.25506.11.1.7.1.3.1.1 |
hpSwitchPortIndexThe ifIndex value which uniquely identifies a row in
the Interfaces Table.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.1 |
hpSwitchPortTypeThe type of port.ro HpSwitchPortType (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.2 |
hpSwitchPortDescrA textual string containing information about the
interface.ro DisplayString .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.3 |
hpSwitchPortAdminStatusThe desired state of the interface. This variable is
similar to the ifAdminStatus but instead of keeping
the operational status, this variable maintain the
desired state in the configuration data base.rwobsolete Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.4 |
hpSwitchPortEtherModeThe type of transmission on this port. This
variable is valid only if the hpSwitchPortType
was Ethernet.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.5 |
hpSwitchPortVgModeThe type of transmission on this port. This variable
is valid only if the hpSwitchPortType was VG.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.6 |
hpSwitchPortLinkbeatThe linkbeat status of this port.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.7 |
hpSwitchPortTrunkGroupThe trunk group this port belong to.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.8 |
hpSwitchPortBcastLimitThe percentage of network bandwidth consumed by
broadcast traffic through this port. If the value of
this variable is 0, there will be no broadcast limit.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.9 |
hpSwitchPortFastEtherModeThe type of transmission on this port. This variable
is valid only if the hpSwitchPortType was Fast
Ethernet.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.10 |
hpSwitchPortFlowControlThe Flow Control of this port.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.11 |
hpSwitchPortTrunkTypeUsed in conjunction with hpSwitchPortTrunkGroup to
determine what type of trunk and which group it
belongs to. If hpSwitchPortTrunkGroup is set to 0,
trunking is disabled on the port and this variable
becomes a 'don't care'rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.13 |
hpSwitchPortTrunkLACPStatusUsed in conjunction with hpSwitchPortTrunkType.
When the trunk is a LACP trunk, this variable defines
its administrative statusrw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.14 |
hpSwitchPortMDIXStatusShows the MDI/MDIX setting for an RJ-45 port.
Returns a value of 'not-applicable' for all
ports except RJ-45 ports.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.15 |
hpSwitchPortAutoMDIXSets the MDI/MDIX value for an RJ-45 port.
Negates need for crossover cables. 'automdix',
'mdi', or 'mdix' may be set when the port
configuration is set to any auto-negotiation mode,
for example 'auto' or 'auto-100', or to any of the
fixed-configuration modes, for example '100-full'.
The MDI/MDIX value is maintained across port
configuration mode changes.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.1.1.16 |
hpSwitchPortConfigStatusThe configuration status of this group of objects. If
one or more variables in this group were
reconfigured since last reboot and required reboot to
take effect, the value of this variable will be set to
notInService.ro ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.3.2 |
hpSwitchLinkUpDownTrapAllPortsStatusUsed to either enable/disable the Link Up/Link Down traps for all the ports.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.3.3 |
hpSwitchIpxConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.4 |
hpSwitchIpxConfigStatusThe status of the IPX configuration table.ro ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.4.2 |
hpSwitchIpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.5 |
hpSwitchIpTimepAdminStatusThe operational status of the Time protocol.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.5.1 |
hpSwitchIpTimepServerAddr### deprecated ### The IP address of the Time server.rwdeprecated IpAddress .1.3.6.1.4.1.25506.11.1.7.1.5.2 |
hpSwitchIpTimepPollIntervalThe client poll interval of the Time server in
minutes.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.5.3 |
hpSwitchIpConfigStatusThe configuration status of the Timep and IP
related objects.roobsolete ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.5.5 |
hpSwitchIpTftpModeThe operational mode of the Tftp protocol.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.5.6 |
hpSwitchIpTimepInetServerAddrTypeThe IP address type of the Time server.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.11.1.7.1.5.7 |
hpSwitchIpTimepInetServerAddrThe IP address (of the Time server)to which this entry's
addressing information pertains.
hpSwitchIpTimepInetServerAddr is always interpreted within
the context of hpSwitchIpTimepInetServerAddrType.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.11.1.7.1.5.8 |
hpSwitchIpTimepIsOobmThis object indicates whether this TIMEP Server
is reachable over OOBM (Out Of Band Management)
interface or not. This mib object will be applicable
only if there is a physical OOBM port on the device.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.5.9 |
hpSwitchSerialLinkConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.6 |
hpSwitchSLinkBaudRateThe rate of data transfer between the console and
the node. baudRate1 is speed sense.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.6.1 |
hpSwitchSLinkFlowCtrlThe flow-control mechanism between the console and
the switch.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.6.2 |
hpSwitchSLinkConnInactTimeThe number of minutes to wait after no character was
input to log out the console. Valid values are 0 (not
to log out of the console for inactivity) through 120
(two hours).rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.6.3 |
hpSwitchSLinkModemConnTimeThe number of seconds to wait for data mode and
clear to send and receiver ready signals after
asserting request to send and terminal ready signals.
Valid values are 0 (switch will wait forever for the
modem) through 300 (5 minutes).rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.6.4 |
hpSwitchSLinkModemLostRecvTimeThe number of milliseconds the receiver ready signal
is allowed to drop before the switch will disconnect
the modem. Valid values are 0 (the switch will wait
forever) through 5000 (5 seconds).rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.6.5 |
hpSwitchSLinkModemDisConnTimeThe number of seconds to wait after the modem is
disconnected before allowing the modem to be
reconnected. Valid values are 0 (allow a connection
as soon as possible, the default) through 60 (1
minute).rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.6.6 |
hpSwitchSLinkParityThe type of parity to use between the console and
the node.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.6.7 |
hpSwitchSLinkCharBitsThe number of bits per character to use between
the console and the node.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.6.8 |
hpSwitchSLinkStopBitsThe number of stop bots to use when communicating
between the console and the node.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.6.9 |
hpSwitchSLinkConfigStatusThe configuration status of this group of objects.
If one or more variables in this group were
reconfigured since last reboot and required reboot
to take effect, the value of this variable will be
set to notInService.ro ConfigStatus (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.6.10 |
hpSwitchFilterConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.8 |
hpSwitchFilterConfigTableA table that contains information about the
traffic filter configuration in this device. SEQUENCE OF HpSwitchFilterConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.8.1 |
hpSwitchFilterConfigEntryInformation about a traffic filter configuration
in this device. HpSwitchFilterConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.8.1.1 |
hpSwitchFilterIndexAn index that uniquely identifies a traffic filter
for which this entry contains information.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.8.1.1.1 |
hpSwitchFilterTypeThe type of filter.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.8.1.1.2 |
hpSwitchFilterSrcPortThis variable is required when a port filter or
unicast filter was configurated. It will be ignored
otherwise.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.8.1.1.3 |
hpSwitchFilterMacAddrThis variable is valid only if a unicast or
multicast filter was defined. It will be ignored
otherwise.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.8.1.1.4 |
hpSwitchFilterProtocolTypeThis variable is valid only if a level-3 filter
was defined. It will be ignored otherwise. This
variable will contain either a etherType (DIX
Ethernet) or SAP(IEEE 802) value of the level-3
protocol.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.8.1.1.5 |
hpSwitchFilterPortMaskThis variable specifies a group of ports whose
traffic will be filtered. Each octet within the value
of this object specifies a set of eight ports, with
the first octet specifying ports 1 through 8, the
second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the switch is represented by a single bit within
the value of this object.rw OCTET STRING .1.3.6.1.4.1.25506.11.1.7.1.8.1.1.6 |
hpSwitchFilterEntryStatusThe status of a filter entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.8.1.1.7 |
hpSwitchProbeConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.9 |
hpSwitchProbeTypeIf the value of this variable is equal to 1, the
probe will monitor those ports specified by
hpSwitchProbedPortMask, otherwise all of the port
belong to the virtual LAN specified by
hpSwitchProbedVlanId will be monitored.rwobsolete Enumeration .1.3.6.1.4.1.25506.11.1.7.1.9.1 |
hpSwitchProbedVlanIdThe probed virtual LAN.rwobsolete VlanID .1.3.6.1.4.1.25506.11.1.7.1.9.2 |
hpSwitchProbePortThe port that every packet passes through those
probed ports will be copied to.rwobsolete INTEGER .1.3.6.1.4.1.25506.11.1.7.1.9.3 |
hpSwitchProbeAdminStatusThe operational status of the probing functionrwobsolete Enumeration .1.3.6.1.4.1.25506.11.1.7.1.9.4 |
hpSwitchProbedPortMaskThis variable specifies a group of ports which will
be probed. Each octet within the value of this
object specifies a set of eight ports, with the
first octet specifying ports 1 through 8, the second
octet specifying ports 9 through 16, etc. Within each
octet, the most significant bit represents the lowest
numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the switch is represented by a single bit within
the value of this object.rwobsolete OCTET STRING .1.3.6.1.4.1.25506.11.1.7.1.9.5 |
hpSwitchFddiIpFragConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.11 |
hpSwitchFddiIpFragConfigTableA list of IP fragmentation configuration
parameters for the FDDI cards in the switch. SEQUENCE OF HpSwitchFddiIpFragConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.11.1 |
hpSwitchFddiIpFragConfigEntryAn Fddi IP fragmentation entry which is
containing configurable options for the FDDI
cards in the switch. HpSwitchFddiIpFragConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.11.1.1 |
hpSwitchFddiIpFragConfigIndexA unique value for each FDDI Card.
The value for each FDDI card must remain constant
at least from one re-initialization of the entity's
network management system to the next
re-initialization.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.11.1.1.1 |
hpSwitchFddiIpFragConfigStatusThe operational status of FDDI IP fragmentation
for each FDDI card.
enable(1): FDDI card will fragment all packets which
are bigger then the Ethernet packet size
limitation, 1518 Bytes.
disable(2): FDDI card will drop all packets which
are bigger then the Ethernet packet size
limitation, 1518 Bytes.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.11.1.1.2 |
hpSwitchABCConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.12 |
hpSwitchABCConfigTableA list of Automatic Broadcast Control (ABC
disable/enable entries for each VLAN on the switch. SEQUENCE OF HpSwitchABCConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.12.1 |
hpSwitchABCConfigEntryContains the ABC status for each VLAN on the switch,
including IP RIP control and IPX RIP/SAP control. HpSwitchABCConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.12.1.1 |
hpSwitchABCConfigVlanThe user is able to enable/disable ABC on a per VLAN
basis, so the VLAN serves as an index into the ABC
configuration table.ro VlanID .1.3.6.1.4.1.25506.11.1.7.1.12.1.1.1 |
hpSwitchABCConfigControlABC control is either IP&IPX or IP or IPX or disabled
for each VLAN on the switch.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.12.1.1.2 |
hpSwitchABCConfigIpRipControlIP RIP control. If this feature is enabled then IP
RIP packets will only be forwarded on ports, within
its VLAN domain, that have heard RIPs before. If
this feature is disabled then IP RIP packets seen by
a given port will be forwarded to all ports within its
VLAN domain.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.12.1.1.3 |
hpSwitchABCConfigIpxRipSapControlIPX RIP/SAP control. If this feature is enabled then
IPX RIP/SAP packets will only be forwarded on ports,
within its VLAN domain, that have previously seen
RIP/SAP packets. If this feature is disabled then
IPX RIP and SAP packets seen by a given port will be
forwarded to all ports within its VLAN domain.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.12.1.1.4 |
hpSwitchABCConfigVlanBcastLimitThe percentage of network bandwidth consumed by
broadcast traffic through VLAN. If the value of this
variable is 0, there will be no broadcast limit. There
is a default value chosen when ABC is enabled.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.12.1.1.5 |
hpSwitchABCConfigAutoGatewayConfigIf this feature is enabled then DHCP packets both
ucast and bcast with UDP destination port 68 will be
intercepted. DHCP packets with the router option in
the options field in the DHCP message will be
modified so that the first daddress in the router
option is the same as the clients address. Thus the
client will be its own default gateway. If this
feature is disabled DHCP packtes will be forwarded as
usual.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.12.1.1.7 |
hpSwitchStpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.14 |
hpSwitchStpVlanTableA table that contains vlan-specific information
for the Spanning Tree Protocol. SEQUENCE OF HpSwitchStpVlanEntry .1.3.6.1.4.1.25506.11.1.7.1.14.1 |
hpSwitchStpVlanEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. HpSwitchStpVlanEntry .1.3.6.1.4.1.25506.11.1.7.1.14.1.1 |
hpSwitchStpVlanThe operational status of the spanning tree
protocol.ro VlanID .1.3.6.1.4.1.25506.11.1.7.1.14.1.1.1 |
hpSwitchStpAdminStatusThe operational status of the spanning tree
protocol.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.14.1.1.2 |
hpSwitchStpPriorityThe value of the write-able portion of the Bridge
ID, i.e., the first two octets of the (8 octet
long) Bridge ID. The other (last) 6 octets of the
Bridge ID are given by the value of
dot1dBaseBridgeAddress.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.14.1.1.3 |
hpSwitchStpMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.rw Timeout .1.3.6.1.4.1.25506.11.1.7.1.14.1.1.4 |
hpSwitchStpHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.rw Timeout .1.3.6.1.4.1.25506.11.1.7.1.14.1.1.5 |
hpSwitchStpForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in each of the Listening and Learning
states, which precede the Forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the Forwarding Database. [Note that
this value is the one that this bridge is
currently using, in contrast to
dot1dBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]rw Timeout .1.3.6.1.4.1.25506.11.1.7.1.14.1.1.6 |
hpSwitchStpPortTableA table that contains port-specific information
for the Spanning Tree Protocol. SEQUENCE OF HpSwitchStpPortEntry .1.3.6.1.4.1.25506.11.1.7.1.14.2 |
hpSwitchStpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. HpSwitchStpPortEntry .1.3.6.1.4.1.25506.11.1.7.1.14.2.1 |
hpSwitchStpPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.1 |
hpSwitchStpPortTypeThe type of port.ro HpSwitchPortType (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.2 |
hpSwitchStpPortSrcMacThe source MAC address used by the spanning
tree protocol.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.3 |
hpSwitchStpPortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
dot1dStpPort.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.4 |
hpSwitchStpPortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port. 802.1D-1990 recommends that the
default value of this parameter be in inverse
proportion to the speed of the attached LAN.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.5 |
hpSwitchStpPortModeIf the value of this variable is set to fast(2), the
port will go directly into the Forwarding State when a
device is connected to it. Use this feature only on
ports that are connected to an individual PC or
Workstation, to allow these ports to come up and
move quickly to the Forwarding State instead of going
through the normal STP initialization process.
Caution: Changing the value of this variable to fast(2)
on ports connected to a hub or switch may cause loops
in your network.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.6 |
hpSwitchStpPortBpduFilterSetting True will cause port to ignore ingress BPDUs
and not generate egress BPDUs, as the result the port
will stay in forwarding state. Default is False.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.7 |
hpSwitchStpPortBpduProtectionSetting True indicates that no BPDUs are expected to
be received on this port. At the reception of BPDUs
the BPDU protection mechanism will disable this port
and port will transition into bpduError state.
Default is False.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.8 |
hpSwitchStpPortErrantBpduCounterCounts the number of BPDUs that were not expected
to be received on this port. This counter gets
incremented only if hpSwitchStpPortBpduProtection,
hpSwitchStpPortBpduFilter, hpSwitchStpPortPvstFilter,
or hpSwitchStpPvstProtection is True for the port,
otherwise it is cleared to zero.ro Counter .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.9 |
hpSwitchStpPortPvstFilterSetting True will cause the port to ignore incoming
PVST BPDUs.
Default is False.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.10 |
hpSwitchStpPortPvstProtectionSetting True indicates that any PVST BPDUs arriving
on this port should be discarded and that this will
cause the port to be disabled. The port will remain
disabled for the time period indicated by
hpSwitchStpBpduProtectionTimeout.
Default is False.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.14.2.1.11 |
hpSwitchStpTrapCntlControls generation of SNMP traps by STP-enabled switch
for events defined in this MIB.
The set bit means 'enabled'.
- errantBpdu(0)
The state of this bit specifies whether the
notification trap allowed to be send when
unexpected (errant) BPDU is received on a port.rw Bits .1.3.6.1.4.1.25506.11.1.7.1.14.3 |
hpSwitchStpBpduProtectionTimeoutThe duration of time in seconds when a protected port
affected by receiving of an unauthorized BPDU will
remain in down state. The zero value means infinity.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.14.4 |
hpSwitchIgmpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.15 |
hpSwitchIgmpConfigTableA table that contains information about the IGMP
Querier capacity or High Priority Forward
configuration on any given vlan on the switch. SEQUENCE OF HpSwitchIgmpConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.15.1 |
hpSwitchIgmpConfigEntryInformation about the IGMP Querier feature associated
with a specific virtal LAN in this device. HpSwitchIgmpConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.15.1.1 |
hpSwitchIgmpVlanIndexAn index that uniquely identifies the IGMP
configuration of a virtual LAN for which this entry
contains information.ro VlanID .1.3.6.1.4.1.25506.11.1.7.1.15.1.1.1 |
hpSwitchIgmpStateThe operational status of the IGMP support for
this virtual LAN.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.15.1.1.2 |
hpSwitchIgmpQuerierStateThe operational status of the IGMP Querier
functionality for this virtual LAN.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.15.1.1.3 |
hpSwitchIgmpPriorityStateThe operational status of the IGMP Forward with High
Priority mode for this virtual LAN.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.15.1.1.4 |
hpSwitchIgmpQuerierIntervalThe time (in seconds) to wait between Querier
election cycles for this virtual LAN.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.15.1.1.5 |
hpSwitchIgmpPortConfigTableA table that contains information about the IGMP port
configurations on this switch. SEQUENCE OF HpSwitchIgmpPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.15.2 |
hpSwitchIgmpPortConfigEntryThe information associated with each IGMP port
configuration. HpSwitchIgmpPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.15.2.1 |
hpSwitchIgmpPortIndexThe ifIndex value which uniquely identifies a row in
the Interfaces Table.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.15.2.1.1 |
hpSwitchIgmpPortTypeThe type of port.ro HpSwitchPortType (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.15.2.1.2 |
hpSwitchIgmpIpMcastStateThe operational status of the IGMP feature for this
port or trunk. 1 implies that all IP Multicast
traffic will be monitored on the port, 2 implies that
IP Multicast traffic will be dropped on the port, and
3 implies that all IP Multicast traffic will be
forwarded without the switch examining it.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.15.2.1.3 |
hpSwitchIgmpPortConfigTable2A table that contains information about the IGMP port
configurations on this switch. This table supercedes
hpSwitchIgmpPortConfigTable for products which support
multiple VLANs on each port. SEQUENCE OF HpSwitchIgmpPortConfigEntry2 .1.3.6.1.4.1.25506.11.1.7.1.15.3 |
hpSwitchIgmpPortConfigEntry2The information associated with each IGMP port
configuration. HpSwitchIgmpPortConfigEntry2 .1.3.6.1.4.1.25506.11.1.7.1.15.3.1 |
hpSwitchIgmpPortVlanIndex2The Vlan Index value which uniquely identifies a row
in the Interfaces Table.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.15.3.1.1 |
hpSwitchIgmpPortIndex2The ifIndex value which uniquely identifies a row in
the Interfaces Table.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.15.3.1.2 |
hpSwitchIgmpPortType2The type of port.ro HpSwitchPortType (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.15.3.1.3 |
hpSwitchIgmpIpMcastState2The operational status of the IGMP feature for this
port or trunk. 1 implies that all IP Multicast traffic
will be monitored on the port, 2 implies that
IP Multicast traffic will be dropped on the port, and
3 implies that all IP Multicast traffic will be
forwarded without the switch examining it.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.15.3.1.4 |
hpSwitchIgmpPortForcedLeaveStateThe operational status of the IGMP feature for this
port or trunk indicates whether any IGMP V2 Leaves
received for an IP Multicast group will cause the
group to be deleted after the
hpSwitchIgmpForcedLeaveInterval if no new IGMP V2
Reports are received for that group. Normal behavior
is for a group issuing a Leave to be deleted after
the Querier's Maximum Response time if no IGMP V2
Report is received.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.15.3.1.5 |
hpSwitchIgmpPortFastLeaveStateThe operational status of the IGMP feature for this
port or trunk indicates whether any IGMP V2 Leaves
received for an IP Multicast group will cause the
group to be deleted immediately on single-
connection ports. Normal behavior is for a group
issuing a Leave to be deleted after the Querier's
Maximum Response time if no IGMP V2 Report is
received.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.15.3.1.6 |
hpSwitchIgmpForcedLeaveIntervalWhen a port's hpSwitchIgmpPortForcedLeaveState is
enabled, this is the amount of time allowed for an
IGMP V2 Report to arrive and cancel deletion of a
multicast group requested by a previous IGMP V2
Leave request.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.15.4 |
hpSwitchCosConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.17 |
hpSwitchCosPortConfigTableA table that contains information about the CoS port
configurations on this switch. SEQUENCE OF HpSwitchCosPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.1 |
hpSwitchCosPortConfigEntryThe information associated with each CoS port
configuration. HpSwitchCosPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.1.1 |
hpSwitchCosPortIndexThe ifIndex value which uniquely identifies a row
in the Interfaces Table.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.1.1.1 |
hpSwitchCosPortTypeThe type of port.rodeprecated HpSwitchPortType (HP-ICF-TC) .1.3.6.1.4.1.25506.11.1.7.1.17.1.1.2 |
hpSwitchCosPortPriorityThe 802.1p priority value to assign to packets
received on the specified port. This value will be
inserted in the 802.1Q tag and the packet will be
placed in the appropriate outbound port queue. The
value of 255 is used to indicate No Override.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.1.1.3 |
hpSwitchCosPortDSCPPolicyThe DSCP Policy to assign to packets received on
the specified Port. This is an index into the
hpSwitchCosDSCPPolicy table, or the value 255
indicating no DSCP Policy exists. This policy is
associated with an 802.1p priority value, which will
be inserted in the 802.1Q tag and will cause the
packet to be placed in the appropriate outbound port
queue. When the packet is IP protocol type, the DSCP
policy value (a Differentiated Services codepoint)
will also be written into the Differentiated-Services
field of the IP Type-of-Service byte.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.1.1.4 |
hpSwitchCosPortResolvedPriorityThe 802.1p priority that will be applied to packets
received on the specified port. This value
represents the actual operating value for this CoS
port entry. A value of 255 represents no override
of the incoming priority.ro INTEGER (0..7 | 255) .1.3.6.1.4.1.25506.11.1.7.1.17.1.1.5 |
hpSwitchCosPortApplyPolicyThis object determines which configuration policy,
noPolicyOverride, hpSwitchCosPortPriority or
hpSwitchCosPortDSCPPolicy, applies for the given
Port CoS entry. These configuration policies are
mutually exclusive of one another.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.1.1.6 |
hpSwitchCosVlanConfigTableA table that contains information about the CoS Vlan
configurations on this switch. SEQUENCE OF HpSwitchCosVlanConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.2 |
hpSwitchCosVlanConfigEntryThe information associated with each CoS Vlan
configuration. HpSwitchCosVlanConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.2.1 |
hpSwitchCosVlanIndexThe index that uniquely identifies the CoS
configuration of a virtual LAN for which this entry
contains information.ro VlanID .1.3.6.1.4.1.25506.11.1.7.1.17.2.1.1 |
hpSwitchCosVlanPriorityThe 802.1p priority value to assign to packets
received on the specified Vlan. This value will be
inserted in the 802.1Q tag and the packet will be
placed in the appropriate outbound port queue. The
value of 255 is used to indicate No Override.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.2.1.2 |
hpSwitchCosVlanDSCPPolicyThe DSCP Policy to assign to packets received on
the specified Vlan. This is an index into the
hpSwitchCosDSCPPolicy table, or the value 255
indicating no DSCP Policy exists. This policy is
associated with an 802.1p priority value, which
will be inserted in the 802.1Q tag and will cause
the packet to be placed in the appropriate outbound
port queue. When the packet is IP protocol type,
the DSCP policy value (a Differentiated Services
codepoint) will also be written into the
Differentiated-Services field of the IP
Type-of-Service byte.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.2.1.3 |
hpSwitchCosVlanResolvedPriorityThe 802.1p priority that will be applied to
packets received on the specified VLAN. This value
represents the actual operating value for this CoS
vlan entry. A value of 255 represents no override of
the incoming priority .ro INTEGER (0..7 | 255) .1.3.6.1.4.1.25506.11.1.7.1.17.2.1.4 |
hpSwitchCosVlanApplyPolicyThis object determines which configuration policy,
noPolicyOverride, hpSwitchCosVlanPriority or
hpSwitchCosDSCPPolicy, applies for this given Vlan
CoS entry. These configuration policies are mutually
exclusive of one another.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.2.1.5 |
hpSwitchCosProtocolConfigTableA table that contains information about the CoS
protocol type configurations on this switch. SEQUENCE OF HpSwitchCosProtocolConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.3 |
hpSwitchCosProtocolConfigEntryThe information associated with each CoS protocol
configuration. HpSwitchCosProtocolConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.3.1 |
hpSwitchCosProtocolTypePackets with this protocol type will receive the new
priority value.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.3.1.1 |
hpSwitchCosProtocolPriorityThe 802.1p priority value to assign to packets
received for the specified protocol. This value will
be inserted in the 802.1Q tag and the packet will be
placed in the appropriate outbound port queue. The
value of 255 is used to indicate No Override.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.3.1.2 |
hpSwitchCosAddressConfigTableA table that contains information about the CoS
address configurations on this switch. SEQUENCE OF HpSwitchCosAddressConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.4 |
hpSwitchCosAddressConfigEntryThe information associated with each CoS address
configuration. HpSwitchCosAddressConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.4.1 |
hpSwitchCosAddressIndexThe index that uniquely identifies the CoS
configuration for an address for which this entry
contains information.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.1 |
hpSwitchCosAddressTypeThe type of address to configure. Default is ip
(IPv4). This field indicates which of the other
address fields must be configured for this table
entry.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.2 |
hpSwitchCosAddressIpThis variable is valid only if an IPv4 CoS
configuration was defined. It will be ignored
otherwise. Packets with this IPv4 address as a source
or destination will receive the new priority value.rw IpAddress .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.3 |
hpSwitchCosAddressPriorityThe 802.1p priority value to assign to packets
received for the specified address. This value will
be inserted in the 802.1Q tag and the packet will be
placed in the appropriate outbound port queue.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.4 |
hpSwitchCosAddressStatusThe status of a Cos Address entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.5 |
hpSwitchCosAddressDSCPPolicyThe DSCP Policy to assign to packets received for
the specified address. This is an index into the
hpSwitchCosDSCPPolicy table, or the value 255
indicating no DSCP Policy exists. This policy is
associated with an 802.1p priority value, which
will be inserted in the 802.1Q tag and will cause
the packet to be placed in the appropriate outbound
port queue. The DSCP policy value (a Differentiated
Services codepoint) will also be written into the
Differentiated-Services field of the IP
Type-of-Service byte.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.6 |
hpSwitchCosAddressResolvedPriorityThe 802.1p priority that will be applied to packets
received for the specified address. This value
represents the actual operating value for this given
address entry. A value of 255 represents no override.ro INTEGER (0..7 | 255) .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.7 |
hpSwitchCosAddressApplyPolicyThis object determines which configuration policy,
hpSwitchCosAddressPriority or hpSwitchCosDSCPPolicy,
applies for the given Address CoS entry. These
configuration policies are mutually exclusive of
one another.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.8 |
hpSwitchCosIpv4AddressMaskThis value is applied as a direct IPv4-address mask
when an IPv4 CoS configuration is defined for this
table entry. It will be ignored otherwise. The
default mask value is 255.255.255.255, which
specifies the exact IPv4 address defined in
hpSwitchCosAddressIp (i.e., no subnet-masking is
performed).rw IpAddress .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.9 |
hpSwitchCosAddressIpv6This variable is valid only if an IPv6 CoS
configuration was defined. It will be ignored
otherwise. Packets with this IPv6 address as a source
or destination will receive the new priority value.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.10 |
hpSwitchCosAddressIpv6PrefixLengthThe prefix length associated with the
hpSwitchCosAddressIpv6 object, if an IPv6 CoS
configuration is valid and hpSwitchCosAddressType is
type ipv6. This variable will otherwise be ignored.
The prefix length for an IPv6 entry functions in the
same way as an address mask for an IPv4 entry. The
default value of this object is 128, which specifies
the exact IPv6 address defined in
hpSwitchCosAddressIpv6 (i.e., no subnet-masking is
performed).rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.25506.11.1.7.1.17.4.1.11 |
hpSwitchCosTosConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.17.5 |
hpSwitchCosTosConfigModeThe operational status of Type of Service based
Class of Service.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.5.1 |
hpSwitchCosTosConfigTableA table that contains information about the CoS Type
of Service configurations on this switch. This table
is used only when the hpSwitchCosTosConfigMode is set
to diffserv. SEQUENCE OF HpSwitchCosTosConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.5.2 |
hpSwitchCosTosConfigEntryThe information associated with each CoS TOS
configuration. HpSwitchCosTosConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.5.2.1 |
hpSwitchCosTosIndexPackets with this value in the upper bits of the Type
of Service field of the IP protocol header will receive
the new priority value. For Differentiated Services
the upper 6 bits of the TOS field are used.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.5.2.1.1 |
hpSwitchCosTosPriorityThe 802.1p priority value to assign to packets
received for the specified TOS. This value will be
inserted in the 802.1Q tag and the packet will be
placed in the appropriate outbound port queue. The
value of 255 is used to indicate No Override.rwdeprecated INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.5.2.1.2 |
hpSwitchCosTosDSCPPolicyThe DSCP Policy to assign to packets received for
the specified ToS codepoint. This is an index
into the hpSwitchCosDSCPPolicy table, or the value
255 indicating no DSCP Policy exists. The DSCP
policy is associated with an 802.1p priority value,
which will be inserted in the 802.1Q tag and will
cause the packet to be placed in the appropriate
outbound port queue. The DSCP policy value (a
Differentiated Services codepoint) will also
replace the incoming value of the Differentiated
Services field of the IP Type-of-Service byte.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.5.2.1.3 |
hpSwitchCosTosResolvedPriorityThe 802.1p priority that will be applied to
packets received for the specified ToS. This
value represents the actual operating value for
this given ToS entry. A value of 255 represents no
override of the incoming priority. If
hpSwitchCosTosApplyPolicy is set to
applyInheritedPriority, the parallel codepoint in
the hpSwitchCosDSCPPolicyConfigTable is used to
determine the operating priority. Otherwise if set
to applyHpSwitchCosTosDSCPPolicy, the priority for
the codepoint that the hpSwitchCosTosDSCPPolicy is
indexing will be used.ro INTEGER (0..7 | 255) .1.3.6.1.4.1.25506.11.1.7.1.17.5.2.1.4 |
hpSwitchCosTosApplyPolicyThis object determines which configuration policy,
applyInheritedPriority or hpSwitchCosTosDSCPPolicy,
applies for the given Tos CoS entry.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.5.2.1.5 |
hpSwitchCosDSCPPolicyConfigTableA table that contains information about the
priority applied to each of the Differentiated
Services Code Points. SEQUENCE OF HpSwitchCosDSCPPolicyConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.6 |
hpSwitchCosDSCPPolicyConfigEntryA list of objects describing a DiffServe Codepoint
(DSCP), and the 802.1p priority to apply for that
DSCP. HpSwitchCosDSCPPolicyConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.6.1 |
hpSwitchCosDSCPPolicyIndexAn index to uniquely identify each row in the
hpSwitchCosDSCPPolicyConfigTable. INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.6.1.1 |
hpSwitchCosDSCPPolicyPriorityThe 802.1p priority value to assign to packets
with a given DSCP. This value will be inserted in
the 802.1Q tag and the packet will be placed in the
appropriate outbound port queue. The value of 255
is used to indicate no override of the incoming
priority.rw INTEGER (0..7 | 255) .1.3.6.1.4.1.25506.11.1.7.1.17.6.1.2 |
hpSwitchCosDSCPPolicyNameA user settable name describing a DSCP policy
table entry.rw OCTET STRING .1.3.6.1.4.1.25506.11.1.7.1.17.6.1.3 |
hpSwitchCosAppTypeConfigTableA table that contains information about the CoS
Application type configurations on the switch. An
application is determined by its network source
and/or destination port number. SEQUENCE OF HpSwitchCosAppTypeConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.7 |
hpSwitchCosAppTypeConfigEntryAn entry in the switch
hpSwitchCosAppTypeConfigEntry Table. HpSwitchCosAppTypeConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.17.7.1 |
hpSwitchCosAppTypeConfigIndexAn index to uniquely identify this
hpSwitchCosAppType row. INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.1 |
hpSwitchCosAppTypeConfigTypeThis signifies which network port number to apply
to the given CoS Application policy.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.2 |
hpSwitchCosAppTypeSrcPortThis object represents the source network port
that this policy applies to.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.3 |
hpSwitchCosAppTypeDestPortThis object represents the destination network
port that this policy applies to.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.4 |
hpSwitchCosAppTypePriorityThe 802.1p priority that should be applied to
packets containing the particular configured source
and/or destination port number in this entry. A
value of 255 represents that no priority override
should take place.rw INTEGER (0..7 | 255) .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.5 |
hpSwitchCosAppTypeDSCPPolicyThe DSCP Policy to assign to packets received for
the specified application. This is an index into
the hpSwitchCosDSCPPolicy table, or the value 255
indicating no DSCP Policy exists. This policy is
associated with an 802.1p priority value, which
will be inserted in the 802.1Q tag and will cause
the packet to be placed in the appropriate outbound
port queue. The DSCP policy value (a
Differentiated Services codepoint) will also be
written into the Differentiated-Services field of
the IP Type-of-Service byte. The value of 255 is
used to indicate No Override.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.6 |
hpSwitchCosAppTypeResolvedPriorityThe 802.1p priority that will be applied to
packets received on the specified application.
This value represents the actual operating value
for this CoS application entry. A value of 255
represents no override of the incoming priorityro INTEGER (0..7 | 255) .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.7 |
hpSwitchCosAppTypeApplyPolicyThis object determines which configuration policy,
hpSwitchCosAppTypePriority or
hpSwitchCosAppTypeDSCPPolicy, applies for the given
AppType CoS entry. These configuration policies
are mutually exclusive of one another.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.8 |
hpSwitchCosAppTypeStatusThis object is used to create and delete in the
hpSwitchCosAppType table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.9 |
hpSwitchCosAppTypeMaxSrcPortThis object represents the maximum source network
port that this policy applies to. If a single,
specific port is being used and not a range, then
value of this object is zero.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.10 |
hpSwitchCosAppTypeMaxDestPortThis object represents the maximum destination
network port that this policy applies to. If a
single, specific port is being used and not a range,
then value of this object is zero.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.11 |
hpSwitchCosAppTypeIpPacketTypeThis object represents the type of IP packet for which
this TCP and/or UDP application QoS will apply. The
default is IPv4.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.7.1.12 |
hpSwitchCosLastChangeThe value of the agent's sysUptime when the last
time this device experienced a change in the
Class of Service configuration.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.25506.11.1.7.1.17.8 |
hpSwitchConfigCosLastConfigErrorThe type of the last QoS
configuration result or error.
This object is updated for each
new QoS configuration. It is
reset upon reboot.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.17.9 |
hpSwitchMeshConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.18 |
hpSwitchMeshMulticastAgingModeWith meshing active, a value of aging will cause
learned multicast addresses to be aged out within
the required address aging interval. A setting of
nonaging will prevent learned multicast addresses
from being removed from the switch. Multicast addresses
learned while in nonaging mode are not removed until
the switch is rebooted.rwdeprecated Enumeration .1.3.6.1.4.1.25506.11.1.7.1.18.1 |
hpSwitchMeshBackwardCompatibilityDue to some hardware differences, the Series
1600/24xx/4000/8000 switches cannot be used
directly in a mesh environment with Series 5300XL
switches. Series 5300XL switches need to emulate
the operation of Series 1600/24xx/4000/8000
switches in order to have a heterogeneous mesh
working properly. Meshing backward-compatibility
feature allows Series 5300XL switches to operate in
a compatible mode in which the operation of Series
1600/24xx/4000/8000 switches are emulated. When
backward-compatibility is enabled, meshing software
will establish connections with Series
1600/24xx/4000/8000 switches and emulate their
operation. When backward-compatibility disabled,
Series 1600/24xx/4000/8000 switches in the mesh
will be ignored by the Series 5300XL switches.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.18.2 |
hpSwitchPortIsolationConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.19 |
hpSwitchPortIsolationModeThis enables the port isolation feature on the device.
Note: Enabling this feature may require VLANS to be
configured properly.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.19.1 |
hpSwitchPortIsolationConfigTableA table that contains information about the CoS
Application type configurations on the switch. An
application is determined by its network source
and/or destination port number. SEQUENCE OF HpSwitchPortIsolationConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.19.2 |
hpSwitchPortIsolationConfigEntryAn entry in the switch
hpSwitchPortIsolationConfigEntry Table. HpSwitchPortIsolationConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.19.2.1 |
hpSwitchPortIsolationPortAn entry in the IfIndex table representing a logical port
on this switch. INTEGER .1.3.6.1.4.1.25506.11.1.7.1.19.2.1.1 |
hpSwitchPortIsolationPortModeDefines the operational mode of a port when Port
Isolation feature is enabled.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.19.2.1.2 |
hpSwitchSshConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.20 |
hpSwitchSshAdminStatusThe status of the SSH operation.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.20.1 |
hpSwitchSshVersionThe version of the SSH protocol to run.
'version1' will accept connections from
v1.3 or v1.5 clients. 'version2' will accept
connections only from v2.0 clients.
The default is 'version1_or_2' which will accept any
connection which can be successfully negotiated.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.20.2 |
hpSwitchSshTimeoutThe maximum length of time (in seconds) between the wakeup
of SSH task and successful protocol negotiation and
authentication. The default is 120 seconds.rw Timeout .1.3.6.1.4.1.25506.11.1.7.1.20.3 |
hpSwitchSshPortNumberThe port number on which SSH daemon should listen for
connection requests.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.20.4 |
hpSwitchSshServerKeySizeSpecifies the key size (in bits) of version 1 SSH host
rsa keyrw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.20.5 |
hpSwitchSshFileServerAdminStatusSpecifies whether or not the SSH daemon will accept
and process file transfer requests.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.20.6 |
hpSwitchSshIpVersion#### THIS OBJECT IS DEPRECATED ####
The types of IP connections SSH will support.
'ipv4' will accept connections from
Ipv4 clients. 'ipv6' will accept
connections only from ipv6 clients.
The default is 'ipv4or6' which will accept
Connections from both ipv4 and ipv6 clients.rwdeprecated Enumeration .1.3.6.1.4.1.25506.11.1.7.1.20.7 |
hpSwitchPendingConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.21 |
hpSwitchPendingConfigControlThe object controls switch pending configuration.
If set to the 'applyMstp' value the object applies
pending Multiple Spanning Tree Protocol (MSTP)
configuration. The 'resetMstp' value, if set, triggers
copying of the active MSTP configuration to the
pending one. Before the pending configuration is applied
its consistency is verified and the request fails if
errors are detected.
The value the object returns is undefined.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.21.1 |
hpSwitchBWMinConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.22 |
hpSwitchBWMinEgressPortConfigTableNew definitions under HP-ICF-RATE-LIMIT-MIB.
A table that contains information about the port's
egress Guaranteed Minimum Bandwidth configurations
on this switch.deprecated SEQUENCE OF HpSwitchBWMinEgressPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.22.1 |
hpSwitchBWMinEgressPortConfigEntryNew definitions under HP-ICF-RATE-LIMIT-MIB.
The information associated with each port's egress
Guaranteed Minimum Bandwidth configuration.deprecated HpSwitchBWMinEgressPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.22.1.1 |
hpSwitchBWMinEgressPortIndexNew definitions under HP-ICF-RATE-LIMIT-MIB.
The ifIndex value which uniquely identifies a row
in the Interfaces Table.rodeprecated INTEGER .1.3.6.1.4.1.25506.11.1.7.1.22.1.1.1 |
hpSwitchBWMinEgressPortPrctLowPriorityNew definitions under HP-ICF-RATE-LIMIT-MIB.
The percentage of Guaranteed Minimum bandwidth to
be assigned to the egress Low-Priority queue for
this port. Total values for all four queues must not
exceed 100 percent.rwdeprecated INTEGER .1.3.6.1.4.1.25506.11.1.7.1.22.1.1.2 |
hpSwitchBWMinEgressPortPrctNormalPriorityNew definitions under HP-ICF-RATE-LIMIT-MIB.
The percentage of Guaranteed Minimum bandwidth to
be assigned to the egress Normal-Priority queue for
this port. Total values for all four queues must not
exceed 100 percent.rwdeprecated INTEGER .1.3.6.1.4.1.25506.11.1.7.1.22.1.1.3 |
hpSwitchBWMinEgressPortPrctMedPriorityNew definitions under HP-ICF-RATE-LIMIT-MIB.
The percentage of Guaranteed Minimum bandwidth to
be assigned to the egress Medium-Priority queue for
this port. Total values for all four queues must not
exceed 100 percent.rwdeprecated INTEGER .1.3.6.1.4.1.25506.11.1.7.1.22.1.1.4 |
hpSwitchBWMinEgressPortPrctHighPriorityNew definitions under HP-ICF-RATE-LIMIT-MIB.
The percentage of Guaranteed Minimum bandwidth to
be assigned to the egress High-Priority queue for
this port. Total values for all four queues must not
exceed 100 percent.rwdeprecated INTEGER .1.3.6.1.4.1.25506.11.1.7.1.22.1.1.5 |
hpSwitchRateLimitPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.23 |
hpSwitchRateLimitPortConfigTableA table that contains information about the port
Rate-Limiting configurations on this switch. SEQUENCE OF HpSwitchRateLimitPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.23.1 |
hpSwitchRateLimitPortConfigEntryThe information associated with each port's
Rate-Limiting configuration. HpSwitchRateLimitPortConfigEntry .1.3.6.1.4.1.25506.11.1.7.1.23.1.1 |
hpSwitchRateLimitPortIndexThe ifIndex value which uniquely identifies a row
in the Interfaces Table.ro INTEGER .1.3.6.1.4.1.25506.11.1.7.1.23.1.1.1 |
hpSwitchRateLimitPortControlModeThe mode by which this port will be Rate-Limited
on ingress. If rateLimitPerPortOnly is configured,
there will be a single maximum rate for the entire
port. If rateLimitPerQueue is configured, the values
for each of the four queues indicate the maximum
percentage of port traffic that may be received by
that queue (the sum of these values must not exceed
100). When rate-limiting is disabled, there are no
maximum controls on ingress for this port.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.23.1.1.2 |
hpSwitchRateLimitPortSingleControlPrctWhen hpSwitchRateLimitPortControlMode is configured
for rateLimitPerPortOnly, this value is the maximum
percentage of traffic that may be received by this
port on ingress.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.23.1.1.3 |
hpSwitchRateLimitPortPrctLowPriorityThe maximum percentage of traffic that may be
received by this port's Low-Priority queue on ingress.
hpSwitchRateLimitPortControlMode must be configured to
use rateLimitPerQueue for this to take effect. A value
of 0-percent for any queue means that no traffic will
ever be received on this port for that ingress queue.
Total values for all four queues must not exceed 100
percent.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.23.1.1.4 |
hpSwitchRateLimitPortPrctNormalPriorityThe maximum percentage of traffic that may be
received by this port's Normal-Priority queue on
ingress. hpSwitchRateLimitPortControlMode must be
configured to use rateLimitPerQueue for this to take
effect. A value of 0-percent for any queue means that
no traffic will ever be received on this port for that
ingress queue. Total values for all four queues must
not exceed 100 percent.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.23.1.1.5 |
hpSwitchRateLimitPortPrctMedPriorityThe maximum percentage of traffic that may be
received by this port's Medium-Priority queue on
ingress. hpSwitchRateLimitPortControlMode must be
configured to use rateLimitPerQueue for this to take
effect. A value of 0-percent for any queue means that
no traffic will ever be received on this port for that
ingress queue. Total values for all four queues must
not exceed 100 percent.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.23.1.1.6 |
hpSwitchRateLimitPortPrctHighPriorityThe maximum percentage of traffic that may be
received by this port's High-Priority queue on
ingress. hpSwitchRateLimitPortControlMode must be
configured to use rateLimitPerQueue for this to take
effect. A value of 0-percent for any queue means that
no traffic will ever be received on this port for that
ingress queue. Total values for all four queues must
not exceed 100 percent.rw INTEGER .1.3.6.1.4.1.25506.11.1.7.1.23.1.1.7 |
hpSwitchQosPassThroughMode OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.24 |
hpSwitchQosPassThroughModeConfigSpecify the queue configuration mode for the switch.
While changing the queue configuration mode this feature
momentarily require to bring down the logical port and
after the initialisation of the queues the ports are
brought up.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.24.1 |
hpSwitchReboot OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.25 |
hpSwitchRebootConfigThis tells the status of the switch whether it requires
reboot for some variable to get effective.
The value of this variable can be
yes (1) reboot is required.
no (2) reboot is not required.ro Enumeration .1.3.6.1.4.1.25506.11.1.7.1.25.1 |
hpSwitchRebootFastBootSpecifies whether fastboot is enabled or not on
the switch.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.25.2 |
hpSwitchProtectedPortsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.26 |
hpSwitchProtectedPortsMaskThis variable specifies a group of ports that are not
allowed to communicate to each-other. Each octet within
the value of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8, the
second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the switch is represented by a single bit within
the value of this object.rw OCTET STRING .1.3.6.1.4.1.25506.11.1.7.1.26.1 |
hpSwitchLACPConfig OBJECT IDENTIFIER .1.3.6.1.4.1.25506.11.1.7.1.28 |
hpSwitchLACPAllPortsStatusUsed to set administrative status of LACP on all the ports.
A Port can have one of the three administrative status of
LACP. Active/Passive/Disabled are the three states.rw Enumeration .1.3.6.1.4.1.25506.11.1.7.1.28.1 |