CAPWAP-MIB
AI MIB Summary
The CAPWAP-MIB provides managed object definitions for monitoring Control and Provisioning of Wireless Access Points (CAPWAP) tunnel states, AP registration status, and data/control channel statistics across wireless LAN controllers and access points. It enables the tracking of specific protocol metrics including tunnel establishment failures, AP mode transitions, and packet counters for both control and data traffic within the CAPWAP architecture.
Copyright (C) 2007 The Internet Society. This version of the MIB module is part of RFC xxx; see the RFC itself for full legal notices. This MIB module contains managed object definitions for the CAPWAP Protocol.
Main OID:
capwapMIB.1.3.6.1.2.1.999901
122
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
122 total| Object Name |
|---|
capwapMIBCopyright (C) 2007 The Internet Society. This version of the MIB module is part of RFC xxx; see the RFC itself for full legal notices. This MIB module contains managed object definitions for the CAPWAP Protocol. MODULE-IDENTITY .1.3.6.1.2.1.999901 |
capwapNotifications OBJECT IDENTIFIER .1.3.6.1.2.1.999901.0 |
capwapChannelUpThis notification is sent by AC when a CAPWAP channel established.The notification is separated for data or control channel. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.1 |
capwapChannelDownThis notification is sent by AC when CAPWAP channel becomes down. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.2 |
capwapDecryptErrorReportThis notification is generated when a WTP that has occurred decryption error since the last report. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.3 |
capwapJoinFailureThis notification is generated when a WTP fails to join. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.4 |
capwapImageUpgradeFailureThis notification is generated when a WTP fails to update software image. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.5 |
capwapConfigMsgErrorThis notification is generated when a WTP received message elements in the Configuration Status Response which it was unable to apply locally. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.6 |
capwapRadioOperableStatusThe notification will notify which radio become inoperable or operable. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.7 |
capwapWTPAuthenticationFailureThe notification will notify the authentication failure event, and provides the reason for it. NOTIFICATION-TYPE .1.3.6.1.2.1.999901.0.8 |
capwapObjects OBJECT IDENTIFIER .1.3.6.1.2.1.999901.1 |
capwapObjectState OBJECT IDENTIFIER .1.3.6.1.2.1.999901.1.1 |
capwapACState OBJECT IDENTIFIER .1.3.6.1.2.1.999901.1.1.1 |
capwapACWTPSessionsRepresents the total number of WTPs which are connecting to AC.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.1.1 |
capwapACWTPSessionsLimitRepresents the maximum number of WTP sessions supported by the AC.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.1.2 |
capwapACStationSessionsRepresents the total number of stations which are accessing the wireless service.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.1.3 |
capwapACStationSessionsLimitRepresents the maximum number of station sessions supported by the AC.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.1.4 |
capwapACDataChannelSecOptionsRepresents the security policy supported for CAPWAP data channel. The AC MAY support more than one option, represented by the bit field below. clear(1) - Clear Text, dtls(2) - DTLS, vendor(3) - vendor specific.ro Integer32 .1.3.6.1.2.1.999901.1.1.1.5 |
capwapACWTPAuthenOptionsRepresents the authentication credentia type supported by the AC for control channel. The AC MAY support more than one option, represented by the bit field below. x509(1) - X.509 Certificate Based psk(2) - Pre-Shared Secret.ro Integer32 .1.3.6.1.2.1.999901.1.1.1.6 |
capwapACHwVersionRepresents the AC's hardware version number.ro OCTET STRING .1.3.6.1.2.1.999901.1.1.1.7 |
capwapACSwVersionRepresents the AC's software version number.ro OCTET STRING .1.3.6.1.2.1.999901.1.1.1.8 |
capwapWTPFallbackEnableRepresents enable or disable automatic CAPWAP fallback in the event that a WTP detects its preferred AC, and is not currently connected to it.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.1.9 |
capwapWTPACNameListRepresent the name list of ACs and use semicolon to separate AC name. The AC name could be configured with the order of Primary AC, secondary AC and so on. WTP will try to connect to AC name in the list one by one till it connected to one AC.rw Unsigned32 .1.3.6.1.2.1.999901.1.1.1.10 |
capwapMaxFailedDTLSSessionRetryRepresent the maximum number of failed DTLS session establishment attempts before the CAPWAP device enters a silent period.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.1.11 |
capwapWTPIdleTimeoutRepresent the time out parameter for WTP idle state.ro Unsigned32 UNITS "kbtyes" .1.3.6.1.2.1.999901.1.1.1.12 |
capwapWTPMaxDiscoveriesRepresent the maximum number of Discovery Request messages that will be sent after a WTP bootsro Unsigned32 .1.3.6.1.2.1.999901.1.1.1.13 |
capwapWTPMaxRetransmitRepresent the maximum number of retransmissions for a given CAPWAP packet before the link layer considers the peer dead.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.1.14 |
capwapWTPReportIntervalRepresents the interval for WTP send report.ro Unsigned32 UNITS "second" .1.3.6.1.2.1.999901.1.1.1.15 |
capwapWTPStateTableThis table provides the state information for WTPs which are accessing to AC via CAPWAP protocol. SEQUENCE OF CapwapWTPStateEntry .1.3.6.1.2.1.999901.1.1.2 |
capwapWTPStateEntryAn entry in this table is created by AC for each WTPs which are accessing to AC via CAPWAP protocol. CapwapWTPStateEntry .1.3.6.1.2.1.999901.1.1.2.1 |
capwapWTPIdRepresents the identifier of a WTP.ro CapwapWTPId .1.3.6.1.2.1.999901.1.1.2.1.1 |
capwapWTPIPAddressRepresents the IP address of a WTP.ro IpAddress .1.3.6.1.2.1.999901.1.1.2.1.2 |
capwapWTPSerialIdRepresents the serial number of a WTP.ro OCTET STRING .1.3.6.1.2.1.999901.1.1.2.1.3 |
capwapWTPStateRepresents WTP current state according to CAPWAP protocol's FSM. The following values are supported: dtls(1) - DTLS negotiation process join(2) - WTP is joining with AC, image(3) - WTP is downloading software, configure(4) - WTP is getting configuration for AC, run(5) - WTP come to run state, clear(6) - WTP is recovery default configuration.ro Enumeration .1.3.6.1.2.1.999901.1.1.2.1.4 |
capwapWTPTableThe table provides information for WTPs in running state. SEQUENCE OF CapwapWTPEntry .1.3.6.1.2.1.999901.1.1.3 |
capwapWTPEntryAn entry in this table is created by AC during CAPWAP protocol process. CapwapWTPEntry .1.3.6.1.2.1.999901.1.1.3.1 |
capwapWTPCurrIdRepresents the unique identifier of a WTP Which is in running state. CapwapWTPId .1.3.6.1.2.1.999901.1.1.3.1.1 |
capwapWTPNameRepresents the name of a WTP.rw DisplayString (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.3.1.2 |
capwapWTPLocationRepresents the name of a WTP.rw DisplayString (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.3.1.3 |
capwapWTPManufacturerIdSMI Network Management Private Enterprise Codes, which are assigned by the IANA. NMS could know which vendor manufactures the WTP.ro OBJECT IDENTIFIER .1.3.6.1.2.1.999901.1.1.3.1.4 |
capwapWTPModelIdRepresents the WTP Model Number.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.3.1.5 |
capwapWTPBoardIdRepresents the WTP hardware identifier.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.3.1.6 |
capwapWTPBoardRevisionRepresents the revision number of the board.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.3.1.7 |
capwapWTPBaseMACAddressRepresents the WTP's Base MAC Address, which MAY be assigned to the primary Ethernet interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.3.1.8 |
capwapWTPTunnelModeOptionsRepresents the tunneling modes for station data that are supported by the WTP. The WTP MAY support more than one option, represented by the bit field below. localBridging(1) - Local Bridging Mode, dot3Tunnel(2) - 802.3 Frame Tunnel Mode, nativeTunnel(3) - Native Frame Tunnel Mode.ro CapwapWTPTunnelMode .1.3.6.1.2.1.999901.1.1.3.1.9 |
capwapWTPMACTypeOptionsRepresents the MAC mode of operation supported by the WTP. The WTP MAY support more than one option, represented by the bit field below. localMAC(1) - Local-MAC Mode, splitMAC(2) - Split-MAC Mode.ro CapwapWTPMACType .1.3.6.1.2.1.999901.1.1.3.1.10 |
capwapWTPDiscoveryTypeRepresents how WTP discovered the AC. The following values are supported: unknown(1) - the method is unknown, staticConfig(2) - static IP configuration, dhcp(3) - DHCP, dns(4) - DNS, acRef(5) - AC Referral.ro Enumeration .1.3.6.1.2.1.999901.1.1.3.1.11 |
capwapWTPRadiosInUseNumberRepresents the number of radios which are in use.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.3.1.12 |
capwapWTPRadioNumLimitRepresents the maximum radio number could be supported by WTP.ro Unsigned32 .1.3.6.1.2.1.999901.1.1.3.1.13 |
capwapWTPSwVersionRepresents the name of WTP software.ro OCTET STRING .1.3.6.1.2.1.999901.1.1.3.1.14 |
capwapWTPSwSizeRepresents the size of WTP software.ro Unsigned32 UNITS "kbtyes" .1.3.6.1.2.1.999901.1.1.3.1.15 |
capwapWTPHwVersionRepresents the version of WTP hardware.ro OCTET STRING .1.3.6.1.2.1.999901.1.1.3.1.16 |
capwapWTPStaticIPEnableRepresents whether the WTP should use a static IP address or not. A value of zero disables the static IP address, while a value of one enables it.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.3.1.17 |
capwapWTPStaticIPWhen capwapWTPStaticIPEnable is true, it represents the static IP address to assign to the WTP.rw IpAddress .1.3.6.1.2.1.999901.1.1.3.1.18 |
capwapWTPNetmaskWhen capwapWTPStaticIPEnable is true, it represents the netmask to assign to the WTP.rw IpAddress .1.3.6.1.2.1.999901.1.1.3.1.19 |
capwapWTPGatewayWhen capwapWTPStaticIPEnable is true, it represents the gateway to assign to the WTP.rw IpAddress .1.3.6.1.2.1.999901.1.1.3.1.20 |
capwapRadioTableThe table will describe WTP and radio's relation-ship. SEQUENCE OF CapwapRadioEntry .1.3.6.1.2.1.999901.1.1.4 |
capwapRadioEntryEach entry contains each radio's information for a specific WTP. CapwapRadioEntry .1.3.6.1.2.1.999901.1.1.4.1 |
capwapRadioIdRepresents the identifier of a radio on a WTP, and only requires unique on a WTP. For example, WTP A and WTP B will use same value for capwapRadioId for their first radio.ro CapwapRadioId .1.3.6.1.2.1.999901.1.1.4.1.1 |
capwapWTPRadioTemplateIfIndexRepresents the ifindex for a interface of 'WTP radio template' interface type. Before WTPs connect to AC and get configuration, administrator will prepare configuration for them. For radio related configuration, administrator could create a logical interface in 'WTP radio template' interface type, and configure radio parameter under it. The configuration and statistic paramter depend on wireless binding type for radio. The 'WTP radio template interface' provides a way to uniquely identify each radio by logical at AC side. As most MIBs use ifindex to identify a interface for configuration and statistic data, for example, 802.11 MIB, it will be very easy to reuse other MIBs like 802.11 MIB by this way. Require IANA to assign a ifType for 'WTP radio template'.rw CapwapWTPRadioTemplateIfIndex .1.3.6.1.2.1.999901.1.1.4.1.2 |
capwapWirelessBindingRepresents the wireless binding type for radio. The following values are supported: none(1) - No any wireless bingding defined. dot11(2) - IEEE 802.11. dot16(3) - IEEE 802.16. epc(4) - EPCGlobal.ro Enumeration .1.3.6.1.2.1.999901.1.1.4.1.3 |
capwapAdminStatusEnableRepresents the administrator status of radio, whether it is enabled or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.4.1.4 |
capwapOperStatusRepresents the operational status of radio, whether it is enabled or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.4.1.5 |
capwapStationTableThis table contains the information of stations which are associating with the specific radio on the WTP. SEQUENCE OF CapwapStationEntry .1.3.6.1.2.1.999901.1.1.5 |
capwapStationEntryEach entry contains information of each station's association information. CapwapStationEntry .1.3.6.1.2.1.999901.1.1.5.1 |
capwapStationIdRepresents the identifier of the station. CapwapStationId .1.3.6.1.2.1.999901.1.1.5.1.1 |
capwapStationAddedTimeThis is the time stamp for the very first time when the station is added.ro TimeStamp (SNMPv2-TC) .1.3.6.1.2.1.999901.1.1.5.1.2 |
capwapStationVlanNameRepresents Vlan name to which the station is associated.ro OCTET STRING .1.3.6.1.2.1.999901.1.1.5.1.3 |
capwapObjectsStats OBJECT IDENTIFIER .1.3.6.1.2.1.999901.1.2 |
capwapWTPRebootStatsTableThe table will provide WTP reboot statistic data. SEQUENCE OF CapwapWTPRebootStatsEntry .1.3.6.1.2.1.999901.1.2.1 |
capwapWTPRebootStatsEntryEach entry of the table will provide the reboot statistic data for a specific WTP. CapwapWTPRebootStatsEntry .1.3.6.1.2.1.999901.1.2.1.1 |
capwapWTPRebootCountRepresents the number of reboots that have occurred due to a WTP crash. A value of 65535 implies that this information is not available on the WTP.ro Counter32 .1.3.6.1.2.1.999901.1.2.1.1.1 |
capwapWTPInitCountRepresents the number of reboots that have occurred at the request of a CAPWAP protocol message, such as a change in configuration that required a reboot or an explicit CAPWAP protocol reset request. A value of 65535 implies that this information is not available on the WTP.ro Counter32 .1.3.6.1.2.1.999901.1.2.1.1.2 |
capwapWTPLinkFailureCountRepresents the number of times that a CAPWAP protocol connection with an AC has failed due to link failure.ro Counter32 .1.3.6.1.2.1.999901.1.2.1.1.3 |
capwapWTPSwFailureCountRepresents the number of times that a CAPWAP protocol connection with an AC has failed due to software related reasons.ro Counter32 .1.3.6.1.2.1.999901.1.2.1.1.4 |
capwapWTPHwFailureCountRepresents the number of times that a CAPWAP protocol connection with an AC has failed due to hardware related reasons.ro Counter32 .1.3.6.1.2.1.999901.1.2.1.1.5 |
capwapWTPOtherFailureCountRepresents the number of times that a CAPWAP protocol connection with an AC has failed due to known reasons, other than AC initiated, link, sofware or hardware failure.ro Counter32 .1.3.6.1.2.1.999901.1.2.1.1.6 |
capwapWTPUnknownFailureCountRepresents the number of times that a CAPWAP protocol connection with an AC has failed for unknown reasons.ro Counter32 .1.3.6.1.2.1.999901.1.2.1.1.7 |
capwapWTPLastFailureTypeThe failure type of the most recent WTP failure. The following values are supported: notSupport(1) - Not Supported, acInit(2) - AC Initiated, linkFailure(3) - Link Failure, swFailure(4) - Software Failure, hwFailure(5) - Hardware Failure, otherFailure(6) - Other Failure, unknown(255) - Unknown (e.g., WTP doesn't keep track of info).ro Enumeration .1.3.6.1.2.1.999901.1.2.1.1.8 |
capwapRadioStatsTableThe table provides statistics on radio behavior and reasons why the WTP radio has been reset. SEQUENCE OF CapwapRadioStatsEntry .1.3.6.1.2.1.999901.1.2.2 |
capwapRadioStatsEntryEach entry of the table will provide the statistic data of event happend on a specific radio of a WTP. CapwapRadioStatsEntry .1.3.6.1.2.1.999901.1.2.2.1 |
capwapRadioResetCountRepresents the number of times that that the radio has been reset.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.1 |
capwapRadioSwFailCountRepresents the number of times that the radio has failed due to software related reasons.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.2 |
capwapRadioHwFailCountRepresents the number of times that the radio has failed due to hardware related reasons.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.3 |
capwapRadioOtherFailCountRepresents the number of times that the radio has failed due to known reasons, other than software or hardware failure.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.4 |
capwapRadioUnknownFailCountRepresents the number of times that the radio has failed for unknown reasons.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.5 |
capwapRadioConfigUpdateCountRepresents the number of times that the radio configuration has been updated.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.6 |
capwapRadioChannelChangeCountRepresents the number of times that the radio channel has been changed.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.7 |
capwapRadioBandChangeCountRepresents the number of times that the radio has changed frequency bands.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.8 |
capwapRadioCurrentNoiseFloorRepresents the noise floor of the radio receiver in units of dBm.ro Integer32 UNITS "dbm" .1.3.6.1.2.1.999901.1.2.2.1.9 |
capwapRadioDecryptErrorCountRepresents the number of decryption errors that occurred on the WTP. Note that this field is only valid in cases where the WTP provides encryption/decryption services.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.10 |
capwapRadioTxQueueLevelRepresents the percentage of Wireless Transmit queue utilization,calaculated as the sum of utilized transmit queue lengths divided by the sum of maximum transmit queue lengths, multiplied by 100.ro Integer32 .1.3.6.1.2.1.999901.1.2.2.1.11 |
capwapRadioRFLinkFramesPerSecRepresents the number of frames transmitted or received per second by the WTP over the aur interface.ro Counter32 .1.3.6.1.2.1.999901.1.2.2.1.12 |
capwapRadioLastFailTypeRepresents the failure type of the most recent radio failure. The following values are supported: notSupport(1) - Not Supported, swFailure(2) - Software Failure, hwFailure(3) - Hardware Failure, otherFailure(4) - Other Failure, unknown(255) - Unknown.ro Enumeration .1.3.6.1.2.1.999901.1.2.2.1.13 |
capwapNotifyVarObjects OBJECT IDENTIFIER .1.3.6.1.2.1.999901.1.3 |
capwapChannelTypeRepresents the channel type for CAPWAP protocol.ro CapwapChannelType .1.3.6.1.2.1.999901.1.3.1 |
capwapWTPAuthenMethodRepresents authentication method for Channel.ro CapwapWTPAuthenMethod .1.3.6.1.2.1.999901.1.3.2 |
capwapChannelDownReasonRepresents the reason for Channel down. The following values are supported: timeout(1) - The keep alive is timeout, rekeyfailure(2) - Rekey process is failed, channel will be broken. apReboot(3) - AC reboot WTP.ro Enumeration .1.3.6.1.2.1.999901.1.3.3 |
capwapIdEntryNumRepresents the entry number of station id in the capwapStationIdList.ro Unsigned32 .1.3.6.1.2.1.999901.1.3.4 |
capwapStationIdListRepresents the list of station id.ro OCTET STRING .1.3.6.1.2.1.999901.1.3.5 |
capwapWTPAuthenFailureReasonRepresents reason for WTP authorization failure. The following values are supported: keyMismatch(1) - WTP's and AC's key is not matched, invalidCA(2) - ca is not valide, micError(3) - detect mic error, timeout(4) - WaitDTLS Timer is timeout, unknown(8) - Unknown reason.ro Enumeration .1.3.6.1.2.1.999901.1.3.6 |
capwapRadioOperStatusFlagRepresents the operation status of a radio. The following values are supported: inoperable(0) - To indicate radio is inoperable, and capwapRadioFailureReason object will give reason in details, operable(1) - To indicate radio is operable.ro Enumeration .1.3.6.1.2.1.999901.1.3.7 |
capwapRadioFailureReasonRepresents errors caused by configuration operation. The following values are supported hwError(1) - Radio Failure, swError(2) - Software Failure, adminSet(3) - Administratively Set, unknown(8) - Unknown reason.ro Enumeration .1.3.6.1.2.1.999901.1.3.8 |
capwapJoinFailureReasonThe following join failure types are supported: unspecified(1) - unspecified failure reason, resDepletion(2) - Resource Depletion, unknownSource(3) - Unknown Source, incorrectData(4) - Incorrect Data, sessionInUse(5) - Session ID already in use, notSupportHw(6) - WTP Hardware not supported, notSupportBinding(7) - Binding Not Supported.ro Enumeration .1.3.6.1.2.1.999901.1.3.9 |
capwapImageFailureReasonThe following software upgrade failure types are supported: invalidChecksum(1) - Invalid Checksum, invalidLength(2) - Invalid Data Length, other(3) - Other Error, inUse(4) - Image Already Present.ro Enumeration .1.3.6.1.2.1.999901.1.3.10 |
capwapConfigMsgErrorTypeThe following software upgrade failure types are supported: unknownElement(1) - Unknown Message Element, unsupportedElement(2) - Unsupported Message Element, unknownValue(3) - Unknown Message Element Value, unsupportedValue(4) - Unsupported Message Element Value.ro Enumeration .1.3.6.1.2.1.999901.1.3.11 |
capwapMsgErrorElementsRepresents the message element sent by the AC in the Configuration Status Response message that caused the error.ro DisplayString (SNMPv2-TC) .1.3.6.1.2.1.999901.1.3.12 |
capwapConformance OBJECT IDENTIFIER .1.3.6.1.2.1.999901.2 |
capwapGroups OBJECT IDENTIFIER .1.3.6.1.2.1.999901.2.1 |
capwapACNodeGroupThe collection of objects which are used to represent basic property for AC from CAPWAP protocol perspective. Unknown .1.3.6.1.2.1.999901.2.1.1 |
capwapWTPStateGroupThe collection of objects which are used to represent WTP state information. Unknown .1.3.6.1.2.1.999901.2.1.2 |
capwapWTPsGroupThe collection of objects which are used to represent configuration,version and property information for WTP in running state. Unknown .1.3.6.1.2.1.999901.2.1.3 |
capwapRadiosGroupThe collection of objects which are used to represent wireless binding type, administrator status and operational status for radio. Unknown .1.3.6.1.2.1.999901.2.1.4 |
capwapStationsGroupThe collection of objects which are used to represent stations' basic property. Unknown .1.3.6.1.2.1.999901.2.1.5 |
capwapWTPsPhysicalGroupCollection of objects that represent hardware information of WTP. Unknown .1.3.6.1.2.1.999901.2.1.6 |
capwapWTPsLayer3GroupCollection of objects that represent layer3 information of WTP. Unknown .1.3.6.1.2.1.999901.2.1.7 |
capwapWTPRebootStatsGroupThe collection of objects which are used for collecting WTP reboot count, link failure count, hardware failure count and so on. Unknown .1.3.6.1.2.1.999901.2.1.8 |
capwapRadioStatsGroupThe collection of objects which are used for collecting radio reset count, channel change count, hardware failure count and so on Unknown .1.3.6.1.2.1.999901.2.1.9 |
capwapNofificationGroupCollection of notifications in this MIB. Unknown .1.3.6.1.2.1.999901.2.1.10 |
capwapNotifyVarGroupObjects used for notification. Unknown .1.3.6.1.2.1.999901.2.1.11 |
capwapCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.999901.2.2 |
capwapFullComplianceCompliance statement for agents that support the configuration and monitoring of CAPWAP MIB. Unknown .1.3.6.1.2.1.999901.2.2.1 |