CALIX-E7-SELT-LINE-MIB
AI MIB Summary
The CALIX-E7-SELT-LINE-MIB enables remote diagnostics and fault isolation on Calix E7 xDSL line cards by monitoring Single-Equipment Line Test (SELT) parameters such as line attenuation, noise margin, and signal-to-noise ratio. This module facilitates the collection of physical layer statistics required to troubleshoot copper-based broadband subscriber connections without requiring physical access to the customer premises.
This MIB Module is for E7 xDSL SELT diagnostics.
Main OID:
e7SeltTestDiags.1.3.6.1.4.1.6321.1.2.2.9
30
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
30 total| Object Name |
|---|
e7SeltTestDiagsThis MIB Module is for E7 xDSL SELT diagnostics. MODULE-IDENTITY .1.3.6.1.4.1.6321.1.2.2.9 |
e7XdslSeltLineTableThe table xdslSeltLineTable contains configuration, command and status parameters of the xDSL line. Several objects in this table MUST be maintained in a persistent manner. SEQUENCE OF E7XdslSeltLineEntry .1.3.6.1.4.1.6321.1.2.2.9.1 |
e7XdslSeltLineEntryThe index of this table is an interface index where the interface has an ifType of xdslSelt(9). E7XdslSeltLineEntry .1.3.6.1.4.1.6321.1.2.2.9.1.1 |
e7XdslUsMarginSelt US Margin.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.1 |
e7XdslDsMarginSelt DS Margin.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.2 |
e7XdslUsNumTonesSelt US Number of Tones.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.3 |
e7XdslDsNumTonesSelt DS Number of Tones.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.4 |
e7XdslUsRateSelt US capacity estimate rate.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.5 |
e7XdslDsRateSelt DS capacity estimate rate.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.6 |
e7XdslBestFitIdxBest fit/match reflection report index.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.7 |
e7XdslLoopTypeLoop Type 0 = Awg 24, 1 = Awg 26.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.8 |
e7XdslLoopLengthLoop Length Estimate in meters.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.9 |
e7XdslFitErrorBest Fit Errorro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.1.1.10 |
e7XdslSeltLineCmndConfLdsfFailReasonThe status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none(1) - The default value in case LDSF was never requested for the associated line. success(2) - The recent command completed successfully. inProgress(3) - The Loop Diagnostics process is in progress. cannotRun(4) - The NE cannot initiate the command, due to a non-specific reason. aborted(5) - The Loop Diagnostics process aborted. failed(6) - The Loop Diagnostics process failed. tableFull(7) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources(8) - The NE cannot initiate the command, due to lack of internal memory resources.ro Enumeration .1.3.6.1.4.1.6321.1.2.2.9.1.1.11 |
e7XdslSeltLineCmndConfLdsfLoop diagnostics mode forced (LDSF) for Selt Test. Defines whether the line should be forced into the Selt loop diagnostics mode by the near-end ATU on this line.rw Enumeration .1.3.6.1.4.1.6321.1.2.2.9.1.1.12 |
e7SeltReportStatusTableThe table SeltReportStatusTable contains status parameters for SELT test reflection report. The parameters in this table MUST be updated after a loop diagnostic procedure completion SEQUENCE OF E7SeltReportStatusEntry .1.3.6.1.4.1.6321.1.2.2.9.2 |
e7SeltReportStatusEntryThe table SeltReportStatusEntry contains status parameters of the SELT test reflection report. The index of this table is an interface index. E7SeltReportStatusEntry .1.3.6.1.4.1.6321.1.2.2.9.2.1 |
e7SeltBestFitIdxSELT test best fit index. The valid values are 0, 1, 2.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.2.1.1 |
e7SeltReportValidSELT test report valid state values. 1 = valid and 0 = not-validro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.2.1.2 |
e7SeltRoundTripDelaySELT test round trip delay.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.3 |
e7SeltRoundTripErrorSELT test round trip error.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.4 |
e7SeltAttn300KHzSELT test attenuation signal 300Khz.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.5 |
e7SeltAttn180KHzSELT test attenuation signal 180Khz.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.6 |
e7SeltAttn1MHzSELT test attenuation signal 1 MHz.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.7 |
e7SeltAttnEndOfRangeSELT test attenuation end of range.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.8 |
e7SeltFitErrorSELT test fit error.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.9 |
e7SeltTerminationPhaseSELT test termination phase.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.10 |
e7SeltTransferFunctionSELT test transfer function.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.2.9.2.1.11 |
e7SeltRangeStartSELT test range start.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.2.1.12 |
e7SeltRangeStopSELT test range stop.ro INTEGER .1.3.6.1.4.1.6321.1.2.2.9.2.1.13 |