Home/Catalog/Avaya_46xxIPTelephone-MIB

Avaya_46xxIPTelephone-MIB

AI MIB Summary

The Avaya_46xxIPTelephone-MIB enables SNMP-based monitoring and management of Avaya 46xx series IP telephones (up to Release 2.8) by exposing device operational status, port statistics, and call session metrics defined in the COMPAS 75441 specification.

MIB Module for 46xx IP Telephones through Release 2.8 in accordance with 46xx Common Requirements COMPAS 75441, Issue 2.8. Copyright 2006 by Avaya Inc. All rights reserved.
Main OID:
endpointMIB.1.3.6.1.4.1.6889.2.69.1
225
Objects
Active
Status
2
Dependencies

Imported Objects

SNMPv2-SMI
RFC1213-MIB

Objects

225 total
Object Name
avaya
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889
avayaProducts
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.1
avayaipEndpointProd
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.1.69
avayaMibs
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2
avayaipEndpointMIBs
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69
endpointMIBMIB Module for 46xx IP Telephones through Release 2.8 in accordance with 46xx Common Requirements COMPAS 75441, Issue 2.8. Copyright 2006 by Avaya Inc. All rights reserved.
MODULE-IDENTITY
.1.3.6.1.4.1.6889.2.69.1
endptID
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69.1.1
endptMARKETID designation. This variable returns a string specifying 'domestic' or 'export'.roobsolete
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.1
endptMODELModel identifier. This variable returns a string of up to 8 ASCII characters.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.2
endptMCIPADDList of call server addresses. This variable returns a sequence of IP addresses, in dotted-decimal orDNS format and separated by commas, of call server IP addresses available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.3
endptMCIPINUSECall server address. This variable returns a 4-octet string specifying the IP address of the call server currently in use.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.4
endptMCPORTTransport layer port number. This variable returns an integer specifying the port number in use by the current call server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.5
endptPHONESNHousing serial number. This variable returns a string of up to 18 ASCII characters, specifying the serial number on the outside of the endpoint's housing.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.6
endptPWBCCPWB comcode. This variable returns a string of up to 9 numerical characters, specifying the comcode or version number of the printed wiring board of the endpoint.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.7
endptPWBSNPWB serial number. This variable returns a string of up to 18 ASCII characters, specifying the serial number on the endpoint's printed wiring board, or N/A if the board has no serial number.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.8
endptETHERADDMAC address. This variable returns a 6-octet string specifying the endpoint's MAC address.ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.1.9
endptESPEEDEthernet interface speed. This variable returns a string specifying the endpoint's Ethernet interface speed in Mbps: '100', '10', or '0'.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.10
endptIPADDIP address. This variable returns a 4-octet string specifying the endpoint's current IP address.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.11
endptDHCPLEASETIMEDuration of IPADD lease. This variable returns an unsigned integer specifying the length of time of the IPADD lease, in seconds as received by DHCP option 51.ro
Integer32
.1.3.6.1.4.1.6889.2.69.1.1.12
endptDHCPLEASERENEWRenewal time of IPADD lease. This variable returns an unsigned integer specifying the length of time at which to renew the IPADD lease, in seconds as received by DHCP option 58.ro
Integer32
.1.3.6.1.4.1.6889.2.69.1.1.13
endptDHCPLEASEREBINDRebind time of IPADD lease. This variable returns an unsigned integer specifying the length of time at which to rebind the IPADD lease, in seconds as received by DHCP option 59.ro
Integer32
.1.3.6.1.4.1.6889.2.69.1.1.14
endptGIPADDList of router addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of routers available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.15
endptGIPINUSERouter address. This variable returns a 4-octet string specifying the IP address of the router currently in use.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.16
endptNETMASKSubnet mask. This variable returns a 4-octet string specifying the subnet mask currently in use.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.17
endptTFTPDIRTFTP server path name. This variable returns a string of 0-127 ASCII characters, specifying the path name currently prepended to file names used in TFTP read operations.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.18
endptTFTPSRVRList of TFTP server addresses. This variable returns a sequence of IP addresses, in dotted-decimal orDNS format and separated by commas, of TFTP servers available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.19
endptTFTPINUSETFTP server address. This variable returns a 4-octet string specifying the IP address of the TFTP server currently in use (or all zeroes if no server used successfully during initialization).ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.20
endptBOOTNAMEBoot code file ID. This variable returns a string specifying the boot code file used to initiate telephone operation.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.21
endptAPPNAMEApplication file ID. This variable returns a string specifying the system-specific application file that should be used for telephone operation.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.22
endptSSONSite-specific option number (SSON). This variable returns an integer between 128 and 254 inclusive, specifying the SSON in use. The default is 176.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.23
endptBBURSTBlackburst flag. This variable returns 0 if Blackburst is currently OFF, else 1.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.24
endptHUBSTATHub flag. This variable has been superseded by endptPHY2STAT.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.25
endptDSCPAUDDSCP for audio. This variable specifies the Differentiated Services Code Point for audio currently in use (between 0 and 63 inclusive).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.26
endptDSCPSIGDSCP for signaling. This variable specifies the Differentiated Services Code Point for signaling currently in use (between 0 and 63 inclusive).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.27
endptL2Q802.1Q framing flag. This variable returns 0 if the Layer 2 802.1Q framing parameter is set to 'auto', 1 if it is set to on/enabled, else 2 for off/disabled.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.28
endptL2QAUDAudio priority. This variable returns an integer between 0 and 7 inclusive specifying the current Layer 2 802.1Q audio priority value.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.29
endptL2QSIGSignaling priority. This variable returns an integer between 0 and 7 inclusive specifying the current Layer 2 802.1Q signaling priority value.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.30
endptL2QVLANTelephone VLAN Identifier. This variable returns an integer between 0 and 4094 inclusive specifying the current Layer 2 802.1Q VLAN Identifier value.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.31
endpt46XXUPGRUpgrade script ID. This variable returns a string of up to 16 ASCII characters specifying the name of the upgrade script retrieved by TFTP after the most recent power-up or reset.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.32
endptDNSSRVRList of DNS server addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of DNS servers available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.33
endptDNSINUSEDNS server address. This variable returns a 4-octet string specifying the IP address of the DNS server currently in use.roobsolete
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.34
endptDOMAINList of DNS domain labels. This variable returns a sequence of labels, separated by periods, for use as the highest-level domain in resolving DNS names in system values.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.35
endptRTCPMONRTCP Monitor address. This variable returns a 4-octet string specifying the IP address of the RTCP monitor currently in use.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.36
endptPHY2STATSecondary Ethernet interface setting. This variable returns 0 if the endpoint's secondary Ethernet interface is currently NOT enabled (or none exists), 1 if the hub is setfor auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.37
endptIRSTATIR Interface flag. This variable returns 0 if the endpoint's IR interface is currently NOT enabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.38
endptSMTPSRVRSMTP server IP addresses. This variable returns a comma-separated list of SMTP server IP addresses available for use, in dotted-decimal or DNS format.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.39
endptDSPVERSIONDSP Version. This variable returns a string of up to 10 characters, that identifies the version of the DSP firmware in the endpoint.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.40
endptLOGSRVREvent Log server address. This variable returns at most one IP address, in dotted-decimal or DNS format, of the server to be used for event logging. This function is intended for Avaya use, in debugging if necessary.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.41
endptLOGSTATEvent Log flag. This variable returns 0 if the endpoint's event logging capability is currently NOT enabled, else 1. This function is intended for Avaya use, in debugging if necessary.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.42
endptAGCHANDHandset AGC status. This variable returns 1 if the endpoint's handset Automatic Gain Control capability is currently enabled, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.43
endptAGCHEADHeadset AGC status. This variable returns 1 if the endpoint's headset Automatic Gain Control capability is currently enabled, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.44
endptPHY1STATEthernet line interface status. This variable returns 0 if the endpoint's Ethernet line interface is currently NOT enabled, 1 if the Ethernet line interface is currently for auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.45
endptL2QSTAT802.1Q tagging flag. This variable returns 0 if the Layer 2 802.1Q tagging parameter is currently OFF, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.46
endptVLANTESTVLAN pause parameter. This variable returns the number of seconds for the endpoint to wait for a DHCPOFFER message when using a non-zero VLAN ID. Valid values are integers from 0 to 999 inclusive.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.47
endptPHONECCPhone comcode. This variable returns a string of up to 9 numerical characters, specifying the comcode of the endpoint itself.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.48
endptVLANLISTVLAN ID list. This variable returns a list of zero or more VLAN IDs.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.49
endptAGCSPKRSpeakerphone AGC status. This variable returns 1 if the endpoint's speakerphone Automatic Gain Control capability is currently enabled, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.50
endptHTTPSRVRHTTP server IP addresses. This variable returns a comma-separated list of HTTP server IP addresses available for use, in dotted-decimal or DNS format.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.51
endptHTTPDIRHTTP server Directory. This variable returns the path used in formation of the URI for HTTP GET operations.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.52
endptHTTPPORTHTTP TCP port number. This variable returns the TCP port number used by HTTP during initialization.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.53
endptHTTPUSEDHTTP initialization server IP address. This variable returns a 4-octet IP address for the HTTP server used during initialization (all zeroes if no server successfully used during initialization).ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.1.54
endptPROCSTATLocal Procedure flag. This variable returns 0 if Local Procedures are currently allowed for this telephone, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.55
endptPROCPSWDLocal Procedure Password. This variable returns 0 if the Local Procedure Password is null, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.56
endptSIGSignaling protocol download flag. This variable returns the integer corresponding to the current signaling protocol.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.57
endptGROUPGroup identifier. This variable returns the integer corresponding to the current group identifier.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.58
endptSNMPADDSNMP source addresses. This variable returns one or more allowable source IP addresses for SNMP queries, in dotted decimal or DNS format.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.59
endptCODESRVRHTTP server addresses. This variable returns zero or more HTTP server addresses for software download, in dotted decimal or DNS format.roobsolete
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.60
endptCODEUSEDHTTP server address used. This variable returns the HTTP server address from CODESRVR used, if any, during initialization, or all zeroes if no HTTP server was used.roobsolete
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.1.61
endptSTATICStatic programming override flag. This variable returns the integer corresponding to the current level of override permissions for static programming.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.62
endptTLSSRVRTLS server addresses. This variable returns zero or more Transport Layer Security server addresses for software download, in dotted decimal or DNS format.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.63
endptTLSUSEDTLS server address used. This variable returns the TLS server address from TLSSRVR used, if any, during initialization, or all zeroes if no TLS server was used.ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.1.64
endptCNAPORTChatter server port. This variable returns the Chatter server registration transport-layer port number (from 0 to 65535; default is 8888).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.65
endptCNASRVRCNA server addresses. This variable returns zero or more Chatter server addresses for network analysis, in dotted decimal or DNS format.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.66
endptDSTOFFSETDaylight Savings Time Offset. This variable returns the offset in local time for Daylight Savings Time. Currently used in SIP phones.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.67
endptDSTSTARTDaylight Savings Time Start. This variable returns the first day or date Daylight Savings Time is effective. Currently used in SIP phones.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.68
endptDSTSTOPDaylight Savings Time Stop. This variable returns the first day or date after Daylight Savings Time is over. Currently used in SIP phones.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.69
endptGMTOFFSETGreenwich Mean Time Offset. This variable returns the offset in local time for Greenwich Mean Time. Currently used in SIP phones.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.70
endptSNTPSRVRSNTP server addresses. This variable returns zero or more SNTP server addresses for obtaining time data, in dotted decimal or DNS format. Currently used in SIP phones.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.71
endptBAKLIGHTOFFBacklight idle timer setting. This variable returns the number of minutes of idle time, after which the telephone backlightis turned off. Range is 0-999, with a default of 120. Used in phones with backlit displays.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.72
endptDOT1XCurrent value for 802.1X handling. This variable returns 0 if the telephone supports unicast Supplicant operation only, with PAE multicast pass-through without proxy Logoff, 1 if the same as 0 but with proxy Logoff, and 2 if Unicast both unicast or Multicast Supplicant operation, without PAE multicast pass- through, is supported. The default is 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.73
endptAUDIOENVAudio environment selection index. This variable returns the current setting from the audio environment table (from 0 to 107, default is 0).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.74
endptAUDIOSTHDAudio headset sidetone setting. This variable returns the current setting (0, 1, or 2; default is 0).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.75
endptAUDIOSTHSAudio handset sidetone setting. This variable returns the current setting (0, 1, or 2; default is 0).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.76
endptDHCPINUSEDHCP server address. This variable returns a 4-octet string specifying the IP address of the DHCP server from which the telephone's IP address was obtained (or all zeroes if the telephone was statically addressed).ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.1.77
endptDHCPLEASEEXPRemaining time of IPADD lease. This variable returns an unsigned integer specifying the length of time in seconds until the expiration of the IP address lease, or 0 if the lease has expired.ro
Integer32
.1.3.6.1.4.1.6889.2.69.1.1.78
endptDHCPSTDDHCP lease violation flag. This variable returns 1 if the telephone is not allowed to use the IP address after its lease has expired, or else 0 if the telephone is allowed to continue operating after the IP address lease has expired.).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.79
endptDHCPT1REMRemaining time until IP address lease renewal. This variable returns an unsigned integer specifying the length of time in seconds until the start of the IP address lease renewal, or 0 if the lease has expired.ro
Integer32
.1.3.6.1.4.1.6889.2.69.1.1.80
endptDHCPT2REMRemaining time until IP address lease renewal. This variable returns an unsigned integer specifying the length of time in seconds until the start of the IP address lease rebindingl, or 0 if the lease has expired.ro
Integer32
.1.3.6.1.4.1.6889.2.69.1.1.81
endptICMPDUICMP Destination support setting. This variable returns 2 if the telephone transmits Destination Unreachable messages with code 2 if the designated transport protocol is not supported AND also if the telephone transmits Destination Unreachable messages with code 3 if a closed UD/TCP port is designated. This variable returns 1 if the telephone only transmits Destination Unreachable messages with code 3 if a closed UD/TCP port is designated. This variable returns 0 if the telephone does not transmit Destination Unreachable messages.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.81
endptICMPREDICMP Redirect support setting. This variable returns 1 if the telephone supports received Redirect messages as specified in RFC 1122, Sections 3.2.2.2 and 3.3.1.2, or 0 if the telephone does not provide this support.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.1.82
endptSSONCONTENTContents of DHCP Site Specific Option Number. This variable returns the data portion of the DHCP SSON as designated by endptNVSSON.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.83
endptBRURIBackup and restore URI. This variable returns a string specifying the URI used for backup and restore files.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.1.84
endptNVM
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69.1.2
endptNVMCIPADDIP address of call server stored in Non-Volatile Memory (NVM). This variable returns a 4-octet string or DNS string. Default is AvayaCallServer.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.1
endptNVMCPORTNVM Transport layer port number. This variable returns an integer specifying the call server port number stored in NVM.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.2
endptNVIPADDNVM IP address. This variable returns a 4-octet string specifying the endpoint's IP address stored in NVM.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.3
endptNVGIPADDNVM Router address. This variable returns a 4- octet string specifying the IP address of the router as stored in NVM.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.4
endptNVNETMASKNVM Subnet mask. This variable returns a 4-octet string specifying the subnet mask as stored in NVM.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.5
endptNVTFTPSRVRNVM TFTP server address. This variable returns a 4-octet string specifying the IP address of the file server as stored in NVM. The default is AvayaTFTPserver.roobsolete
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.6
endptNVSSONNVM Site-specific option number. This variable returns an integer between 128 and 254 inclusive, specifying the SSON stored in NVM. The default is 176.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.7
endptNVBBURSTNVM Blackburst flag. This variable returns 0 if the Blackburst parameter in NVM is OFF, else 1.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.8
endptNVHUBSTATNVM Hub flag. This variable has been superseded by endptNVPHY2STAT.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.9
endptNVDSCPAUDNVM DSCP for audio. This variable specifies the Differentiated Services Code Point for audio stored in NVM (integer between 0 and 63 inclusive).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.10
endptNVDSCPSIGNVM DSCP for signaling. This variable specifies the Differentiated Services Code Point for signaling stored in NVM (integer between 0 and 63 inclusive).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.11
endptNVL2QNVM 802.1Q flag. This variable returns 0 if the Layer 2 802.1Q framing parameter in NVM is set to 'auto', 1 if it is set to on/enabled, else 2 for off/disabled.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.12
endptNVL2QAUDNVM Audio priority. This variable returns an integer between 0 and 7 inclusive specifying the Layer 2 802.1Q audio priority value stored in NVM.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.13
endptNVL2QSIGNVM Signaling priority. This variable returns an integer between 0 and 7 inclusive specifying the Layer 2 802.1Q signaling priority value stored in NVM.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.14
endptNVL2QVLANNVM VLAN Identifier. This variable returns an integer between 0 and 4094 inclusive specifying the Layer 2 802.1Q VLAN Identifier value stored in NVM.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.15
endptNVPHY2STATNVM Secondary Ethernet interface setting. This variable returns 0 if the endpoint's secondary Ethernet interface in NVM is currently NOT enabled(or none exists), 1 if the hub is set for auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.16
endptNVLOGSTATNVM Event Log flag. This variable returns 0 if the endpoint's event logging capability in NVM is currently NOT enabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.17
endptNVAGCHANDNVM Handset AGC status. This variable returns 1 if the endpoint's handset Automatic Gain Control capability in NVM is currently enabled, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.18
endptNVAGCHEADNVM Headset AGC status. This variable returns 1 if the endpoint's headset Automatic Gain Control capability in NVM is currently enabled, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.19
endptNVIRSTATNVM IR Interface flag. This variable returns 0 if the endpoint's IR interface capability in NVM is currently NOT enabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.20
endptNVPHY1STATNVM Ethernet line interface status. This variable returns 0 if the endpoint's Ethernet line interface in NVM iscurrently NOT enabled, 1 if the Ethernet line interface in NVM is currently for auto-negotiation, 2 for 10Mbps half-duplex, 3 for 10Mbps full-duplex, 4 for 100Mbps half-duplex, and 5 for 100Mbps full-duplex.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.21
endptNVVLANTESTNVM VLAN pause parameter. This variable returns the number of seconds stored in NVM for the endppoint to wait for a DHCPOFFER message when using a non-zero VLAN ID. Valid values are integers from 0 to 999 inclusive.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.22
endptNVVLANLISTNVM VLAN ID list. This variable returns a list of zero or more VLAN IDs in NVM.roobsolete
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.23
endptNVAGCSPKRSpeakerphone AGC status. This variable returns 1 if the endpoint's speakerphone Automatic Gain Control capability in NVM is currently enabled, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.24
endptNVHTTPSRVRNVM HTTP server IP addresses. This variable returns a comma-separated list of HTTP server IP addresses available for use as stored in NVM, in dotted-decimal format.roobsolete
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.25
endptNVAUTHScript file authentication flag. This variable returns 1 if the endpoint must authenticate script files, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.26
endptNVFILESRVRNVM File server address. This variable returns a 4-octet string specifying the IP address of the file server as stored in NVM.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.2.27
endptNVALERTAlerting Mode flag. This variable returns 1 if the alerting mode setting in non-volatile memory is enabled, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.28
endptNVCHADDRManually-entered DHCP chaddr value. This variable returns a manually-entered value for the DHCP chaddr field as stored in non-volatile memory, if any. A Hexadecimal value with range of 0 (the default) to 999999.ro
Integer32
.1.3.6.1.4.1.6889.2.69.1.2.29
endptNVCONTRASTDisplay Contrast setting. This variable returns the value of the display contrast setting in non-volatile memory. Range is 0-15, with 8 the default.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.2.30
endptMaintenance
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69.1.3
endptUPGRADESCRIPTScript loading status flag. This variable returns '0' if the upgrade script (endpt46XXUPGR) was successfully obtained and interpreted since the last power-up or reset. This variable returns '1' if the upgrade script was successfully obtained and but NOT successfully interpreted since the last power-up or reset. This variable returns '2' if the upgrade script was NOT successfully obtained since the last power-up or reset.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.3.1
endptAPPINUSEApplication file name. This variable returns the name of the application file in the endpoint.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.3.2
endptAPPSTATApplication download flag. This variable returns '0' if the most recent attempt to download and store an application file was successful. This variable returns '1' if the most recent attempt to download an application file was successful but the file was not successfully stored in NVM. This variable returns '2' if the most recent attempt to download an application file was NOT successful.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.3.3
endptRecentLogEach entry is one of up to 75 syslog event messages added since last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first.
SEQUENCE OF EndptRecentLogEntry
.1.3.6.1.4.1.6889.2.69.1.3.4
endptRecentLogEntryEach entry is one of up to 75 syslog event messages added since last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first.
EndptRecentLogEntry
.1.3.6.1.4.1.6889.2.69.1.3.4.1
endptRecentLogTextSyslog event message.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.3.4.1.1
endptResetLogEach entry is one of up to 75 syslog event messages added before the last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first.
SEQUENCE OF EndptResetLogEntry
.1.3.6.1.4.1.6889.2.69.1.3.5
endptResetLogEntryEach entry is one of up to 75 syslog event messages added before the last reset or power-up, each of which has severity code less than the value of NVLOGLOCAL. Entries are in chronological order, oldest first.
EndptResetLogEntry
.1.3.6.1.4.1.6889.2.69.1.3.5.1
endptResetLogTextSyslog event message.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.3.5.1.1
endptDEFINITY
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69.1.4
endptPORTAUDTransport-layer audio port. This variable returns the endpoint's transport layer port number for audio, currently in use.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.1
endptPORTSIGTransport-layer signaling port. This variable returns the endpoint's transport layer port number for signaling, currently in use.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.2
endptFEIPADDAudio endpoint address. This variable returns a 4-octet string specifying the address of the far-end audio endpoint currently in use.ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.4.3
endptFEPORTAudio endpoint port number. This variable returns the far-end endpoint's transport layer port number for audio, currently in use.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.4
endptCODECRReceive codec. This variable returns the designation of the Receive codec currently in use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.4.5
endptCODECTTransmit codec. This variable returns the designation of the Transmit codec currently in use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.4.6
endptJCPCJitter compensation packet count. This variable returns the Jitter compensation packet count currently in use (between 0 and 20, inclusive).ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.7
endptTMSECTransmit buffer fill level. This variable returns the transmit buffer minimum fill level, in msec, currently in use.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.8
endptNVPHONEXTEndpoint's phone extension. This variable returns a text string identifying the endpoint's extension, in free text format. The default value is NULL.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.4.9
endptL2QBBE802.1Q BBE priority value. This variable returns an integer between 0 and 7 inclusive specifying the far-end endpoint's Layer 2 Better than Best Effort audio priority value.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.10
endptDSCPBBEDSCP BBE priority value. This variable returns an integer between 0 and 7 inclusive specifying the far-end endpoint's DiffServ Better than Best Effort audio priority value.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.11
endptRTCPCONTRTCP Control flag. This variable returns 0 if the RTCP control status is off/disabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.12
endptRTCPFLOWRTCP Flowrate. This variable returns an integer between 0 and 65335 inclusive specifying the RTCP flowrate in milliseconds.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.13
endptRSVPCONTRSVP Control flag. This variable returns 0 if the RSVP control status is off/disabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.14
endptRSVPRFRSHRSVP Refresh rate. This variable returns an integer between 0 and 65335 inclusive specifying the RSVP refresh rate in milliseconds.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.15
endptRSVPRTRYRSVP Failed Retry flag. This variable returns 0 if the RSVP Failed Retry Reservation control status is off/disabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.16
endptRSVPPROFRSVP profile flag. This variable returns 0 if the RSVP profile is guaranteed, else 1 for controlled load.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.17
endptPHNCCTelephone country code. This variable returns 1-3 digits; the administered international country code for the location of the serving call server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.18
endptPHNDPLENGTHTelephone dial plan length. This variable returns 1 or 2 digits (3-10); the length of the administered dial plan for the serving call server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.19
endptPHNICTelephone international access code. This variable returns 1-4 digits; the digits dialed to access public network international trunks from the serving call server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.20
endptPHNLDTelephone long distance access code. This variable returns 1 digit or Null; the digit dialed to access public network long distance trunks from the serving call server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.21
endptPHNLDLENGTHLength of national telephone number. This variable returns 1 or 2 digits (5-15); the number of digits in the longest possible national telephone number for the location of the serving call server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.22
endptPHNOLOutside line access code. This variable returns 1 or 2 digits or Null; the digit(s) dialed to access public network local trunks from the serving call server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.23
endptNTWKAUDIONetwork audio quality display flag. This variable returns 0 if the Network audio quality display status is off/disabled, else 1. This flag does not apply to the 4610, 4620, or 4630 IP Telephones.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.24
endptENHDIALSTATEnhanced Local Dialing status. This variable returns 0 if the Enhanced Local Dialing status is off/disabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.25
endptRESTORESTATFTP Backup/restore status. This variable returns 0 if the automatic FTP backup and restore feature status is off/disabled, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.26
endptFTPUSERSTATFTP User permissions status. This variable returns 0 if the user may not change previously-administered FTP server and Directory data, 1 if the user may change or create both FTP server and Directory data, and 2 if the user may only change or create FTP Directory data.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.4.27
endptRASGkListEach entry is one of up to 30 gatekeeper addresses in dotted-decimal or DNS format, as downloaded from the call server during RAS. Entries are listed in the order received.
SEQUENCE OF EndptRASGkEntry
.1.3.6.1.4.1.6889.2.69.1.4.28
endptRASGkEntryEach entry is one of up to 30 gatekeeper addresses in dotted-decimal or DNS format, as downloaded from the call server during RAS. Entries are listed in the order received.
EndptRASGkEntry
.1.3.6.1.4.1.6889.2.69.1.4.28.1
endptRASGkEntryDataData for an individual RAS-provided Gatekeeper.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.4.28.1.1
endptAdvApps
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69.1.5
endptCIBURLDocumentation URL. This variable returns a URL of the directory in which the web-based Customer Information Booklet web pages are located.roobsolete
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.1
endptDIRSRVRLDAP Server address. This variable returns a the IP address of the LDAP server to be used for the phone's Directoryapplication, in dotted decimal or DNS format.ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.5.2
endptDIRTOPDNDirectory Top Name. This variable returns a string specifying the Topmost Distinguished Name in the LDAP Directory to be used for the 4630's Directory application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.3
endptDIRFULLNAMEDirectory FullName Label. This variable returns a string specifying the LDAP Directory's Full Name Field Label, to be used for the 4630's Directory application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.4
endptDIRTELNUMDirectory Phone Number Label. This variable returns a string specifying the LDAP Directory's Telephone Number Field Label, to be used for the 4630's Directory application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.5
endptDIRSRCHTIMEDirectory Search Duration. This variable returns an integer specifying the maximum number of seconds the LDAP Directory should be searched before reporting completion or failure of the search.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.6
endptDIRSRVRPWDDirectory Access Password. This variable returns a string specifying the password used for accessing the LDAP Directory. The null string is returned if no password has been specified.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.7
endptDIRUSERIDDirectory Access User ID. This variable returns a string specifying the User identity used for accessing the LDAP Directory. The null strong is returned if no user ID has been specified.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.8
endptDIRCODINGDirectory Coding Scheme. This variable returns a string specifying the character coding scheme (e.g. ASCII or Latin-1) to be used for LDAP Directory queries.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.9
endptDIRSTATDirectory Connection Status. This variable returns an integer specifying the result code for the most recent Bind Request sent by the 4630 to the LDAP server.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.10
endptFTPSRVRFTP Server address. This variable returns the IP address of the FTP server to be used for the phone's file storage and retrieval, in dotted decimal or DNS format.ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.5.11
endptFTPDIRFTP Server directory. This variable returns a path name of the directory on the FTP server to be used for the phone's file storage and retrieval.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.12
endptPHNEMERGNUMEmergency number. This variable returns a string specifying the emergency number to be outpulsed when the user presses the optional Emergency button in the 4630 Speed Dial application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.13
endptPHNNUMOFCANumber of Call Appearances. This variable returns the number of Call Appearances downloaded from the DEFINITY during registration to the 4630, 462x and 4610SW.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.14
endptPHNNUMOFFBNumber of Feature Buttons. This variable returns the number of administered Feature Buttons downloaded from the switch during registration to the 4630, 462x and 4610SW.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.15
endptWEBCODINGWeb Coding Scheme. This variable returns a string specifying the character coding scheme (e.g. ASCII or Latin-1) to be used for characters entered on forms on web pages. Used by the 4630 Web application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.16
endptWEBEXCEPTWeb Proxy Server Exception List. This variable returns a string specifying a list of one or more HTTP proxy server Exception domains, separated by commas with no intervening spaces, up to 127 total characters. Used by the 4630 Web application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.17
endptWEBHOMEWeb application URL. This variable returns a URL of the Home page for the 4630 Web application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.18
endptWEBPORTWeb application TCP port. This variable returns an integer specifying the TCP port most recently used for the HTTP proxy server. Used by the 4630 Web application.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.19
endptWEBPROXYWeb Proxy Server. This variable returns an IP addresses, in dotted-decimal or DNS format, of an HTTP proxy server. Used by the 4630 Web application.ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.5.20
endptDIRLDAPPORTLDAP Directory Port. This variable returns the port number for LDAP messages, and has a default value of 389.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.21
endptVMLCODINGVoice Mail Coding Scheme. This variable returns a string specifying the character coding scheme (e.g. ASCII or Latin-1) to be used for characters entered on forms on the 4630 Voice Mail application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.22
endptVMLHOMEVoice Mail application URL. This variable returns a URL of the Home page for the 4630 Voice Mail application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.23
endptCLACTIVECall Log activation flag. This variable returns 0 if the call log status is off/disabled, else 1.roobsolete
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.24
endptWMLCODING4610SW/2x Web Coding Scheme. This variable returns a string specifying the character coding scheme (e.g. ASCII or Latin-1) to be used for characters entered on forms on web pages. Used by the 4610SW/462x Web application.roobsolete
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.25
endptWMLEXCEPT4610SW/2x Web Proxy Server Exception List. This variable returns a string specifying a list of one or more HTTP proxy server Exception domains, separated by commas with no intervening spaces, up to 127 total characters. Used by the 4610SW/462x Web application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.26
endptWMLHOME4610SW/2x Web application URL. This variable returns a URL of the Home page for the 4610SW/462x Web application.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.27
endptWMLPORT4610SW/2x Web application TCP port. This variable returns an integer specifying the TCP port most recently used for the HTTP proxy server. Used by the 4610SW/462x Web application.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.28
endptWMLPROXY4610SW/2x Web Proxy Server. This variable returns an IP addresses, in dotted-decimal or DNS format, of an HTTP proxy server. Used by the 4610SW/2x Web application.ro
OCTET STRING
.1.3.6.1.4.1.6889.2.69.1.5.29
endptCTISTATCTI flag. This variable returns 0 if the CTI application is set to off, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.30
endptCTIUDPPORTCTI application UDP port. This variable returns an integer specifying the UDP port most recently used for the UDP listener to receive broadcast messages.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.31
endptSTKSTATStock Ticker flag. This variable returns 0 if the 4630 Stock Ticker application is set to off, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.32
endptSUBSCRIBELIST4610SW/2x Web push subscription list. This variable returns a string containing one or more fully qualified URLs to which the phone's Web application subscribes for potential pushed content.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.33
endptTPSLIST4610SW/2x Web Trusted Push Server list. This variable returns a string containing one or more domains and paths in DNS format, used to determine for validation of push requests.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.34
endptWMLIDLETIMEWeb Idle Timer. This variable returns the number of minutes, from 1 to 60 inclusive, of idle activity on the telephone before the Web Idle Timer URI is displayed.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.5.35
endptWMLIDLEURIWeb Idle Timer URI. This variable returns the URI of the WML page displayed after the 4610SW/462x Web Idle Timer expires.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.5.36
endptAdjuncts
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69.1.6
endptFKEUFKEU flag. This variable returns 0 if the Feature Key Expansion Unit is off, disabled, or not present, else 1.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.6.1
endptFKEUHEALTHFKEU flag. This variable returns 1 if the most recent self-test of the Feature Key Expansion Unit or the 4620 failed, else 0.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.6.2
endptSIP
OBJECT IDENTIFIER
.1.3.6.1.4.1.6889.2.69.1.7
endptCALLFWDSTATCall Forwarding setting. This variable returns the sum of all Call Forwarding permissions. Range is 0 to 7, with 0 as the default.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.1
endptCOVERAGEADDRCall Coverage Server address. This variable returns the URI to which call coverage is sent; up to 255 characters.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.2
endptDATETIMEFORMATDate and Time format specification. This variable returns a parameter indicating the desired format for display of date and time. Range is 0 to 3, with 0 as the default.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.3
endptMUSICSRVRList of music server addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of music servers available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.4
endptMUSICSRVRINUSEMusic server address. This variable returns a 4-octet string specifying the IP address of the music server most recently used.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.7.5
endptMWISRVRList of message waiting indicator server addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of message waiting indicator servers available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.6
endptMWISRVRINUSEMessage waiting indicator server address. This variable returns a 4-octet string specifying the IP address of the message waiting indicator server most recently used.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.7.7
endptREGISTERWAITRegistration wait interval. This variable returns the number of seconds between attempts to re-register with the current server. Range is 0 to 65535, with 3600 as the default.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.8
endptSIPPROXYSRVRList of SIP Proxy server addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of SIP Proxy servers available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.9
endptSIPPROXYSRVRINUSESIP Proxy server address. This variable returns a 4-octet string specifying the IP address of the SIP Proxy server most recently used.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.7.10
endptSIPREGISTRARList of SIP registrar addresses. This variable returns a sequence of IP addresses, in dotted-decimal format and separated by commas, of SIP registrars available for use.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.11
endptSIPREGISTRARINUSESIP registrar address. This variable returns a 4-octet string specifying the IP address of the SIP registrar most recently used.ro
IpAddress
.1.3.6.1.4.1.6889.2.69.1.7.12
endptSPEAKERSTATSpeaker setting. This variable returns a parameter indicating the allowed level of speakerphone functionality. Range is 0 to 2, with 2 as the default.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.13
endptSIPPORTTCP/UDP port used for SIP messages. This variable returns the current port number used for SIP messaging. The default is 5060.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.14
endptSIPDOMAINSIP registration domain name. This text is used in the Contact header field as part of SIP registration.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.15
endptPHNNUMOFSANumber of Session Appearances. This variable returns the number of Session Appearances administered for the SIP phone.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.16
endptDIALWAITDialing timeout interval. This variable returns the number of seconds after the user stops dialing, that the telephone waits before automatically dialing the number enterered so far. The range is 0 to 10, and zero seconds means the telephone will wait forever, or until the user presses Send.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.17
endptDIALPLANSIP dial plan. This variable returns the administered dial plan, used during manual dialing to allow a call to be initiated without the use of a Send button and without waiting for the expiration of a timeout interval; up to 1000 characters.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.18
endptCALLFWDADDRCall Forwarding address. This variable returns the URI to which calls are forwarded; up to 255 characters.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6889.2.69.1.7.19
endptCALLFWDDELAYCall Forwarding delay. This variable returns the number of times the telephone will ring before a call is forwarded, if Call Forwarding on No Answer is selected.ro
INTEGER
.1.3.6.1.4.1.6889.2.69.1.7.20
Avaya_46xxIPTelephone-MIB - SNMP MIB Reference | MIBs Explorer