ATM-SWITCHING-NODE-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ATM-SWITCHING-NODE-MIB.
240
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
240 total| Object Name |
|---|
ibm OBJECT IDENTIFIER .1.3.6.1.4.1.2 |
SNMPv2-TC Unknown .1.3.6.1.4.1.2 |
ibmProd OBJECT IDENTIFIER .1.3.6.1.4.1.2.6 |
atmSw OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33 |
node OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1 |
helloA hello trap is sent:
- when the system re-initializes: it is sent every minutes until
an SNMP request is received or until 255 minutes have passed.
- when one of the following parameters is changed:
The value of ifPhysAddress is the ATM address of the hub.
The hello trap may be disabled. TRAP-TYPE .1.3.6.1.4.1.2.6.33.1.0.1 |
lockA lock trap is sent when a set request is rejected because it is
suspected that this may cause to break the link between the agent
and the manager. This may occur when:
- isolating a slot
- disabling a port
if the request is received through this specific port/module/slot. TRAP-TYPE .1.3.6.1.4.1.2.6.33.1.0.2 |
changeA change trap is sent when one of the following MIB variables or
group of variables is changed:
- Date and Time reset
- System Parameters (name, contact, location) changed
- Interface changed:
- Module changed:
When one of this variable is changed, the lastChange MIB object is
also updated with the current date and time.
When the Date and Time or the System Parameters changed,
the interface number of the hub virtual interface is returned.
This trap may be disabled. TRAP-TYPE .1.3.6.1.4.1.2.6.33.1.0.3 |
pvcFailureA PVC failure trap is sent when a PVC becomes inoperational. TRAP-TYPE .1.3.6.1.4.1.2.6.33.1.0.4 |
callLoggingOverflowA callLoggingOverflow trap is sent when the call logging table
is about to wrap. TRAP-TYPE .1.3.6.1.4.1.2.6.33.1.0.6 |
moduleInstalledAn ATM module has been detected in the hub. TRAP-TYPE .1.3.6.1.4.1.2.6.33.1.0.7 |
moduleRemovedAn ATM module is no longer detected in the hub. TRAP-TYPE .1.3.6.1.4.1.2.6.33.1.0.8 |
base OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.1 |
dateTimeThe local date and time in the ATM agent.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.1.1 |
lastChangeThe date and time of the last major change detected:
- date and time reset
- agent IP address(es), subnet mask(s), default gateway changed
- LAN Emulation or IP ARP server address(es) changed
- system parameters (name, contact, location) changed
- module Changed
- interface changed:
This variable is updated in relation with the following traps:
- hello trap
- change trap
- linkUp/linkDown traps.rodeprecated DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.1.2 |
ipArpServerAtmAddressThe ATM address of the ARP server used when communicating
with the switch agent using Classical IP over ATM (RFC 1577).rw AtmAddress .1.3.6.1.4.1.2.6.33.1.1.4 |
systemStateThe state of the ATM subsystem.
Setting this variable to reset, causes a reset of all the
ATM modules.
When the active switch is in slots 9/10, switch-a is returned.
When the active switch is in slots 11/12, switch-b is returned.rw Enumeration .1.3.6.1.4.1.2.6.33.1.1.6 |
traps OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.2 |
physical OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.3 |
switchTableThis table controls slot attachement to the ATM switch.
An ATM module is operational only when inserted in a slot which
is defined as attached to the switch. SEQUENCE OF SwitchEntry .1.3.6.1.4.1.2.6.33.1.3.1 |
switchEntryEntries of switchTable. Each entry corresponds to a slot that
is physically wired to the switch. These slots may be attached
to or isolated from the ATM switch. SwitchEntry .1.3.6.1.4.1.2.6.33.1.3.1.1 |
switchSlotIndexA slot number controlled by the switch.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.1.1.1 |
switchAdminStateThe desired state of the slot connection to the switch.
When a slot is isolated from the switch, the switch traffic
from this slot to the switch is disabled. As a result, if
an ATM module is plugged in this slot, it will not be
operational.
When a slot is attached to the switch, the switch is ready
to receive ATM traffic from this slot. As a result, if an
ATM module is plugged in this slot, it can be used for
ATM traffic.rw Enumeration .1.3.6.1.4.1.2.6.33.1.3.1.1.2 |
switchOperStateThe actual state of the slot connection to the switch.
When the administrative state is set to ISOLATE, the
operational state becomes ISOLATED.
When the operational state is set to ATTACH, the operational
state may become either ATTACHED or ISOLATED depending on
the hardware current status of the slot.ro Enumeration .1.3.6.1.4.1.2.6.33.1.3.1.1.3 |
moduleTableThis table provides the list of ATM modules in the hub. SEQUENCE OF ModuleEntry .1.3.6.1.4.1.2.6.33.1.3.2 |
moduleEntryEntries of moduleTable. ModuleEntry .1.3.6.1.4.1.2.6.33.1.3.2.1 |
moduleSlotIndexThe slot number for this module.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.2.1.1 |
moduleTypeThe type of module attached to the ATM switch in this
slot.
The 'unknown' value is used when the ATM agent
is unable to get information for this module (the
module is isolated from the switch or is not operational).ro Enumeration .1.3.6.1.4.1.2.6.33.1.3.2.1.2 |
moduleDescriptionA textual description of this module.
This description is blank when no description is available.ro DisplayString .1.3.6.1.4.1.2.6.33.1.3.2.1.3 |
moduleSerialNumberThe serial number for this module.ro DisplayString .1.3.6.1.4.1.2.6.33.1.3.2.1.4 |
moduleSoftwareVersionThe version and release number for this module
firmware (microcode).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.3.2.1.5 |
moduleHardwareVersionThe Part Number (P/N) and Engineering Change (EC) level
for this module and Plant Location.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.3.2.1.6 |
moduleAdminStateThe administrative state of this module.rw Enumeration .1.3.6.1.4.1.2.6.33.1.3.2.1.7 |
moduleOperStateThe operational test of this module.ro Enumeration .1.3.6.1.4.1.2.6.33.1.3.2.1.8 |
moduleErrorsThe number of errors detected by this module on the traffic
from the switch to this module.ro Counter .1.3.6.1.4.1.2.6.33.1.3.2.1.9 |
moduleMaxVpcThe maximum number of VPC supported by this module.
The current number of VPC that can be used is the difference
between moduleMaxVpc and moduleUsedVpc.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.2.1.10 |
moduleUsedVpcThe number of VPCs currently in use for this module.
The current number of VPCs that can be used is the difference
between moduleMaxVpc and moduleUsedVpc.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.2.1.11 |
moduleMaxVccThe maximum number of VCCs supported by this module.
The current number of VCCs that can be used is the difference
between moduleMaxVcc and moduleUsedVcc.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.2.1.12 |
moduleUsedVccThe number of VCC currently in use for this module.
The current number of VCC that can be used is the difference
between moduleMaxVcc and moduleUsedVcc.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.2.1.13 |
portTableThis table provides the list of ports attached to
the ATM switch (ATM ports). These ports belong to ATM modules
inserted in slots that are attached to the ATM switch. SEQUENCE OF PortEntry .1.3.6.1.4.1.2.6.33.1.3.3 |
portEntryEntries of portTable. Each entry corresponds to a port that
belongs to an ATM module. This module must be inserted in a
slot that is attached to the ATM switch. PortEntry .1.3.6.1.4.1.2.6.33.1.3.3.1 |
portSlotIndexThe slot number of this port's module.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.3.1.1 |
portIndexThe port number for this module.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.3.1.2 |
portInterfaceThe interface number of this port.ro IfIndex .1.3.6.1.4.1.2.6.33.1.3.3.1.3 |
interfaceTableFor each ATM port, this table maps the MIB-II interface index for
this port with its physical slot and port numbers. SEQUENCE OF InterfaceEntry .1.3.6.1.4.1.2.6.33.1.3.4 |
interfaceEntryEntries of the interfaceTable.
Each entry corresponds to a port that belongs to an ATM module.
This module must be inserted in a slot
that is attached to the ATM switch. InterfaceEntry .1.3.6.1.4.1.2.6.33.1.3.4.1 |
interfaceIndexThe interface number of the port represented by this entry.
This is the same number as the index used to represent this
interface in the MIB-II interface table.ro IfIndex .1.3.6.1.4.1.2.6.33.1.3.4.1.1 |
interfaceSlotThe slot number of this ATM port's module.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.4.1.2 |
interfacePortThe port number of this ATM port.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.4.1.3 |
interfaceConnectorWhether this port is an internal port (on the backplane)
or an external connector.ro Enumeration .1.3.6.1.4.1.2.6.33.1.3.4.1.4 |
interfaceAdminStateThe administrative state for this port.
When set to disabled, no ATM traffic can pass on this
port; all connections (SVC and PVC) are cleared.
When set to wrap-reply, this interface is wrapped so that
all the traffic received from the attached line is sent
back on this line. If the interface state is not changed,
it will automatically go back to the disabled state after
one minute.rw Enumeration .1.3.6.1.4.1.2.6.33.1.3.4.1.5 |
interfaceOperStateThe operational state for this port:
- unknown: the status of this port is unknown (this can
be the result of a module in error)
- disabled-nosignal: no activity is detected at the physical
layer while the port is enabled
- disabled-idle:: activity from the remote device
attached to this port has been
detected by the physical layer.
The port is disabled.
- failing: an internal hard error has been detected on
this port while the port is enabled
- no signal: no activity is detected at the physical
layer while the port is enabled
- idle: activity from the remote device attached to this
port has been detected by the physical layer.
The port is enabled.
- in-service: the remote device successfully acknowledges
ILMI polling requests and SVC registration
- pvcOnly: the remote device succesfully acknowledges
ILMI polling requests but it rejects the ATM
prefix registration. Only PVCs are supported.
- misConfigured: an SSI to UNI or an SSI to NNI configuration
has been detected
- wrongNetworkPrefix: the switches on each end of an SSI link
have incompatible network prefixes (the
12 first bytes have different values)
- wrongNodeNumber: the switches on each end of an SSI link
have the same ATM node Numbers.
- failing-line: the port is enabled and a invalid
signal is detected on the line
- disabled-failing: the port is disabled and an
anomaly is detected, either internal
or external.
- wrap-no-signal: the port is internally wrapped so that
all the traffic received on the attached line is
returned unchanged on the line.
No activity is detected at the physical
layer.
- wrap-idle: the port is internally wrapped so that
all the traffic received on the attached line is
returned unchanged on the line and
a valid signal is detected on the line.
- wrap-failing-internal: an internal failure has been
detected when the port has been
turned into the wrap-reply state.
The actual state of the port is
undefined.
- wrap-failing-line: the port is internally wrapped so that
all the traffic received on the attached
line is returned unchanged on the line
and an invalid signal is detected
on the line.
When disabled, the port may be in only one of the following
states:
- unknown, disabled-failing, disabled-nosignal or
disabled-idle.ro Enumeration .1.3.6.1.4.1.2.6.33.1.3.4.1.6 |
interfaceAtmAccessThe type of ATM access offered on this port:
- UNI: User Network Interface
- SSI: Switch-to-Switch interface
- NNI: Network-to-Network interfacerw Enumeration .1.3.6.1.4.1.2.6.33.1.3.4.1.7 |
interfaceMediaTypeThe type of cable attached to this port.ro Enumeration .1.3.6.1.4.1.2.6.33.1.3.4.1.8 |
interfaceMediaSpeedThe speed of this interface, in bits per second.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.4.1.9 |
interfaceMediaErrorsThe number of physical layer errors detected on this media
such as violation errors and length errors.ro Counter .1.3.6.1.4.1.2.6.33.1.3.4.1.10 |
interfaceSubSlotWhen set to 0, this interface (and its physical connector)
is directly located on the module identified by the slot
number.
When set to a non-zero value, this number identifies a
feature card of the module that is used by this interface.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.4.1.11 |
interfaceClockingThe source of the bit clock used for data transmission.
When set to external, the source is the clock received
from the line.rw Enumeration .1.3.6.1.4.1.2.6.33.1.3.4.1.12 |
interfaceScramblingWhether data scrambling is used when transmitting on this
line. Scrambling may be applied at the cell level,
at the frame level or at cell and frame level.rw Enumeration .1.3.6.1.4.1.2.6.33.1.3.4.1.13 |
interfaceAvailableBandwidthFor a UNI or a NNI port: the current bandwidth available
for the reserved bandwidth connections on this port.
For a SSI port: the current bandwidth available
on this port.
It is in bits per second.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.4.1.14 |
interfaceAllocatedBandwidthFor a UNI or a NNI port: the bandwidth, in bits per second,
currently used by the reserved bandwidth connections
on this port.
For a SSI port: the bandwidth, in bits per second,
currently reserved on this port.ro INTEGER .1.3.6.1.4.1.2.6.33.1.3.4.1.15 |
switchStats OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.3.5 |
switchMonitoringWhen on, the switch throughput is monitored.
When off, the switch thoughput is not monitored.
Note that the monitoring decreases the system
overall performances.rw Enumeration .1.3.6.1.4.1.2.6.33.1.3.5.1 |
switchAggregateOutCellsThe total number of cells transmitted from the
switch.
Note that this value is the aggregate throughput
of all the ports on several minutes.ro Counter .1.3.6.1.4.1.2.6.33.1.3.5.2 |
receiveTopListThe ifindexes of the five most receiving interfaces.
The first ifindex given is the one corresponding to
the interface which has received the more cells
during the last polling interval.
All ifIndexes are separated by a blank character.
If there are less than 5 interfaces receiving data,
there are less than 5 ifindexes listed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.3.5.3 |
transmitTopListThe ifindexes of the five most transmitting interfaces.
The first ifindex given is the one corresponding to
the interface which has sent the more cells
during the last polling interval.
All ifIndexes are separated by a blank character.
If there are less than 5 interfaces transmitting data,
there are less than 5 ifindexes listed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.3.5.4 |
connections OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.4 |
vcXConnectTableThis table contains the cross-connections set-up in
the switch for all existing VCL-based PVCs and SVCs. SEQUENCE OF VcXConnectEntry .1.3.6.1.4.1.2.6.33.1.4.1 |
vcXConnectEntryEntries of vcXConnectTable. VcXConnectEntry .1.3.6.1.4.1.2.6.33.1.4.1.1 |
vcXInIndexThe interface number for this ATM port.ro IfIndex .1.3.6.1.4.1.2.6.33.1.4.1.1.1 |
vcXInVpiThe VPI value for this connection.ro INTEGER .1.3.6.1.4.1.2.6.33.1.4.1.1.2 |
vcXInVciThe VCI value for this connection.ro INTEGER .1.3.6.1.4.1.2.6.33.1.4.1.1.3 |
vcXOutIndexThe interface number for this ATM port.ro IfIndex .1.3.6.1.4.1.2.6.33.1.4.1.1.4 |
vcXOutVpiThe VPI value for this connection.ro INTEGER .1.3.6.1.4.1.2.6.33.1.4.1.1.5 |
vcXOutVciThe VCI value for this connection.ro INTEGER .1.3.6.1.4.1.2.6.33.1.4.1.1.6 |
vcXTypeWhether this cross-connection is part of a unicast or a
multicast connection.ro Enumeration .1.3.6.1.4.1.2.6.33.1.4.1.1.7 |
vcXDirectionWhether this entry identifies this cross-connection in
the upstream or downstream flow, as seen from the root.
Downstream means that the connection was set up from the
in parameters (interface, VPI, VCI) to the out parameters
(interface, VPI, VCI).
In particular, for a multicast SVC, this means that the
call initiator (the root in this case) is on the interface
side labeled vcXInIndex.
Upstream means that the connection was set up from the
out parameters (interface, VPI, VCI) to the in parameters
(interface, VPI, VCI).
As a result, any cross-connection is modeled in this table
as two entries, depending on whether it is seen in the
up or down stream.ro Enumeration .1.3.6.1.4.1.2.6.33.1.4.1.1.8 |
vpXConnectTableThis table contains the cross-connections set-up in
the switch for all existing VPL-based PVCs and SVCs. SEQUENCE OF VpXConnectEntry .1.3.6.1.4.1.2.6.33.1.4.2 |
vpXConnectEntryEntries of vpXConnectTable. VpXConnectEntry .1.3.6.1.4.1.2.6.33.1.4.2.1 |
vpXInIndexThe interface number for this ATM port.ro IfIndex .1.3.6.1.4.1.2.6.33.1.4.2.1.1 |
vpXInVpiThe VPI value for this connection.ro INTEGER .1.3.6.1.4.1.2.6.33.1.4.2.1.2 |
vpXOutIndexThe interface number for this ATM port.ro IfIndex .1.3.6.1.4.1.2.6.33.1.4.2.1.3 |
vpXOutVpiThe VPI value for this connection.ro INTEGER .1.3.6.1.4.1.2.6.33.1.4.2.1.4 |
vpXTypeWhether this cross-connection is part of a unicast or a
multicast connection.ro Enumeration .1.3.6.1.4.1.2.6.33.1.4.2.1.5 |
vpXDirectionWhether this entry identifies this cross-connection in
the upstream or downstream flow, as seen from the root.
Downstream means that the connection was set up from the
in parameters (interface, VPI) to the out parameters
(interface, VPI).
Upstream means that the connection was set up from the
out parameters (interface, VPI) to the in parameters
(interface, VPI).
As a result, any cross-connection is modeled in this table
as two entries, depending on whether it is seen in the
up or down stream.ro Enumeration .1.3.6.1.4.1.2.6.33.1.4.2.1.6 |
neighbor OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.5 |
nbrTableThis table contains basic characteristics on adjacent
ATM devices attached to this switch. SEQUENCE OF NbrEntry .1.3.6.1.4.1.2.6.33.1.5.1 |
nbrEntryEntries of neighborTable. Each entry corresponds to a port that
belongs to an ATM module. This module must be inserted in a slot
that is attached to the ATM switch. NbrEntry .1.3.6.1.4.1.2.6.33.1.5.1.1 |
localIndexThe interface number for the port represented by this
entry.ro IfIndex .1.3.6.1.4.1.2.6.33.1.5.1.1.1 |
nbrIpAddress1One of the IP addresses of the ATM SNMP agent of the node
attached to the port/slot defined by this entry.
When not available, 0.0.0.0 is returned.ro IpAddress .1.3.6.1.4.1.2.6.33.1.5.1.1.2 |
nbrIpAddress2One of the IP addresses of the ATM SNMP agent of the node
attached to the port/slot defined by this entry.
When not available, 0.0.0.0 is returned.ro IpAddress .1.3.6.1.4.1.2.6.33.1.5.1.1.3 |
nbrAtmAddressThe ATM identification of the node attached to the
port/slot defined by this entry.
When not available, a null string is returned.ro AtmAddress .1.3.6.1.4.1.2.6.33.1.5.1.1.4 |
nbrIndexThe interface number of the adjacent node to which the
connection defined by this entry is attending.
When not available, 0 is returned.ro IfIndex .1.3.6.1.4.1.2.6.33.1.5.1.1.5 |
nbrDescriptorThe value of the MIB-II sysDescr as reported by the
device attached to this port.
When not available, a null string is returned.ro DisplayString .1.3.6.1.4.1.2.6.33.1.5.1.1.6 |
nbrOidThe value of the MIB-II sysOID as reported by the
device attached to this port.
When not available, a null string is returned.ro OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.5.1.1.7 |
nbrNameThe value of the MIB-II sysName as reported by the
device attached to this port.
When not available, a null string is returned.ro DisplayString .1.3.6.1.4.1.2.6.33.1.5.1.1.8 |
nbrLocationThe value of the MIB-II sysLocation as reported by the
device attached to this port.
When not available, a null string is returned.ro DisplayString .1.3.6.1.4.1.2.6.33.1.5.1.1.9 |
trunkIdThe internal identifier for this trunk.
Set to 0 if not a trunk.ro INTEGER .1.3.6.1.4.1.2.6.33.1.5.1.1.10 |
tftp OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.6 |
transferControlA file transfer is initiated through a start command.rw Enumeration .1.3.6.1.4.1.2.6.33.1.6.1 |
transferDateThe date and time of the last transfer.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.6.2 |
serverIpAddressThe IP address of the server used for file transfer.rw IpAddress .1.3.6.1.4.1.2.6.33.1.6.3 |
fileNameThe name of the file to transfer.rw DisplayString .1.3.6.1.4.1.2.6.33.1.6.4 |
fileTypeThe type of file to transfer.
Boot and operational codes can only be dowlnoaded.
Logs, traces and dumps can only be uploaded.rw Enumeration .1.3.6.1.4.1.2.6.33.1.6.5 |
fileTargetThe module target to which the transfer applies.
When set to 0, the transfer applies to the agent itself.rw INTEGER .1.3.6.1.4.1.2.6.33.1.6.6 |
transferResultThe result of the latest file transfer.
When one of the TFTP variables is modified, this
variable is reset to not-initialized.ro Enumeration .1.3.6.1.4.1.2.6.33.1.6.7 |
service OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.7 |
traces OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.7.1 |
sysTraceWhen on, the hub general trace facility is started.
Messages are stored in the hub in a file that can be
retrieved through TFTP.
When off, the general trace facility is stopped and
messages are no longer logged.rw Enumeration .1.3.6.1.4.1.2.6.33.1.7.1.1 |
trsTraceWhen on, the Topology and Routing Selection trace is
started.
Messages are stored in the hub in a file that can be
retrieved through TFTP.
When off, the control point trace facility is stopped and
messages are no longer logged.rw Enumeration .1.3.6.1.4.1.2.6.33.1.7.1.2 |
dumps OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.7.2 |
trsDumpWhen start is selected, a dump of the Topology and Route
Services component is taken.
The dump is stored in the hub in a file that can be
retrieved through TFTP.rw Enumeration .1.3.6.1.4.1.2.6.33.1.7.2.2 |
swap OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.7.3 |
swapControlWhen swap is selected, the backup microcode image is
checked and, if valid, activated.
The previously active microcode image becomes
the backup image.
The atm subsystem is reset.rw Enumeration .1.3.6.1.4.1.2.6.33.1.7.3.1 |
swapResultThe result of the latest microcode swap.
When an operational code image is downloaded or
when the system is reset, swapControl becomes
not-initialized.ro Enumeration .1.3.6.1.4.1.2.6.33.1.7.3.2 |
atmSvc OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.9 |
atmQ2931 OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.9.1 |
atmQ2931ConfTableThis table contains basic information on the Q2931 protocol
for each signalling link defined per port.
Usually, there is only one signalling channel per interface
and thus one Q2931 protocol definition entry per interface. SEQUENCE OF AtmQ2931ConfEntry .1.3.6.1.4.1.2.6.33.1.9.1.1 |
atmQ2931ConfEntryEntries of atmQ2931ConfTable. Each entry corresponds to a pair
of ATM interface, signalling channel.
A signalling channel is uniquely defined on each interface
by the VPI and VCI values allocated to it. AtmQ2931ConfEntry .1.3.6.1.4.1.2.6.33.1.9.1.1.1 |
atmQ2931ConfIndexThe ifIndex value of the ATM interface which, with the
signalling channel defined by its Vpi/Vci values,
uniquely identifies this entry.ro IfIndex .1.3.6.1.4.1.2.6.33.1.9.1.1.1.1 |
atmQ2931SiVpiThe Vpi value which, with the Vci value specified in
atmQ2931SiVci, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.2 |
atmQ2931SiVciThe Vci value which, with the Vpi value specified in
atmQ2931SiVpi, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.3 |
atmQ2931T303T303 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.4 |
atmQ2931T308T308 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.5 |
atmQ2931T309T309 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.6 |
atmQ2931T310T310 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.7 |
atmQ2931T316T316 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.8 |
atmQ2931T317T317 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.9 |
atmQ2931T322T322 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.10 |
atmQ2931T398T398 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.11 |
atmQ2931T399T399 timer as defined in the ATM UNI Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.12 |
atmQ2931SetupRetryNumber of set-up retries as defined in the ATM UNI
Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.13 |
atmQ2931ReleaseRetryNumber of release retries as defined in the ATM UNI
Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.14 |
atmQ2931RestartRetryNumber of restart retries as defined in the ATM UNI
Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.15 |
atmQ2931StatusRetryNumber of status retries as defined in the ATM UNI
Specification.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.1.1.16 |
atmQ2931StatsTableThis table contains statistics for the Q2931 protocol. SEQUENCE OF AtmQ2931StatsEntry .1.3.6.1.4.1.2.6.33.1.9.1.2 |
atmQ2931StatsEntryEntries of atmQ2931ConfTable. Each entry corresponds to a pair
of ATM interface, signalling channel.
A signalling channel is uniquely defined on each interface
by the VPI and VCI values allocated to it. AtmQ2931StatsEntry .1.3.6.1.4.1.2.6.33.1.9.1.2.1 |
atmQ2931StatsIndexThe ifIndex value of the ATM interface which, with the
signalling channel defined by its Vpi/Vci values,
uniquely identifies this entry.ro IfIndex .1.3.6.1.4.1.2.6.33.1.9.1.2.1.1 |
atmQ2931StatsVpiThe Vpi value which, with the Vci value specified in
atmQ2931StatsVci, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.2.1.2 |
atmQ2931StatsVciThe Vci value which, with the Vpi value specified in
atmQ2931StatsVpi, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.2.1.3 |
atmQ2931OutCallAttemptsThis is the number of outgoing call attempts on this
interface, including accepted as well as rejected calls.ro Counter .1.3.6.1.4.1.2.6.33.1.9.1.2.1.4 |
atmQ2931OutCallInProgessThis is the current number of outgoing calls in progress
on this interface.ro Gauge .1.3.6.1.4.1.2.6.33.1.9.1.2.1.5 |
atmQ2931OutCallFailuresThis is the number of outgoing calls that were cleared
for a reason other than a DTE or operator initiated action.ro Counter .1.3.6.1.4.1.2.6.33.1.9.1.2.1.6 |
atmQ2931InCallAttemptsThis is the number of incoming call attempts on this
interface, including accepted as well as rejected calls.ro Counter .1.3.6.1.4.1.2.6.33.1.9.1.2.1.7 |
atmQ2931InCallInProgressThis is the current number of incoming calls in progress
on this interface.ro Gauge .1.3.6.1.4.1.2.6.33.1.9.1.2.1.8 |
atmQ2931InCallFailuresThis is the number of calls that were rejected by the
receiver.ro Counter .1.3.6.1.4.1.2.6.33.1.9.1.2.1.9 |
atmSvcTableThis table contains basic information for each active
Switched Virtual Connection (SVC). SEQUENCE OF AtmSvcEntry .1.3.6.1.4.1.2.6.33.1.9.1.3 |
atmSvcEntryEntries of atmSvcTable. Each entry uniquely
defines two end-points of an SVC. In the case of a
multicast SVC, each entry is defined by the
association of the root and one party. AtmSvcEntry .1.3.6.1.4.1.2.6.33.1.9.1.3.1 |
atmSvcInterfaceIndexThe ifIndex value of the ATM interface used by this
SVC.ro IfIndex .1.3.6.1.4.1.2.6.33.1.9.1.3.1.1 |
atmSvcSiVpiThe Vpi value which, with the Vci value specified in
atmQ2931SiVci, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.3.1.2 |
atmSvcSiVciThe Vci value which, with the Vpi value specified in
atmQ2931SiVpi, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.3.1.3 |
atmSvcCallReferenceThe Q2931 call reference value used for this SVC.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.3.1.4 |
atmSvcEndPointReferenceOne of the Q2931 end point reference values used by this
SVC.
In a unicast SVC, there is only one entry for this SVC in
the table.
In a multicast SVC, there is one entry per party.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.3.1.5 |
atmSvcCallingNumberThe calling number carried in the calling party number
information element of the call set-up message.ro AtmAddress .1.3.6.1.4.1.2.6.33.1.9.1.3.1.6 |
atmSvcCalledNumberThe called number carried in the called party number
information element of the call set-up message.ro AtmAddress .1.3.6.1.4.1.2.6.33.1.9.1.3.1.7 |
atmSvcClearThis variable allows a network manager to clear this
SVC.
When this SVC is cleared (either by the manager using
this variable or by one of the parties), the entry is
deleted from this table and another entry is created
in the atmSvcClearTable.rw Enumeration .1.3.6.1.4.1.2.6.33.1.9.1.3.1.8 |
atmSvcCreationTimeThe date and time this call was placed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.9.1.3.1.9 |
atmSvcVpiThe VPI value used by this SVC for this interface.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.3.1.10 |
atmSvcVciThe VCI value used by this SVC for this interface.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.3.1.11 |
atmSvcLogSizeThe maximum number of entries supported by this local
SNMP agent.
When this value is exceeded, the entries are wrapped.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.4 |
atmSvcLogLevelThe maximum number of entries that can be written in the
atmSvcLogTable before a trap is generated.
When this number is reached, an svcLogOverflow trap is
generated.
When set to 0, no trap is generated.rw INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.5 |
atmSvcLogTableThis table contains a list of the latest Switched
Virtual Connection (SVC) that were completed on this
ATM node.
An SVC is completed when it has been torn down at the
originator's request (normal completion) or by the
network operator (forced tear down), or when it has
been rejected or cleared by the network (exceptional
condition). SEQUENCE OF AtmSvcLogEntry .1.3.6.1.4.1.2.6.33.1.9.1.6 |
atmSvcLogEntryEntries of atmSvcLogTable. AtmSvcLogEntry .1.3.6.1.4.1.2.6.33.1.9.1.6.1 |
atmSvcLogIndexAn identification value for this entry, assigned by the
local SNMP agent.
This value is assigned for each new SVC call or
add-party request.
This index is allocated in a decreasing order, so that
a get-next request on the table allows to retrieve the
latest calls first.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.6.1.1 |
atmSvcLogInterfaceIndexThe ifIndex value of the ATM interface used by this
SVC.ro IfIndex .1.3.6.1.4.1.2.6.33.1.9.1.6.1.2 |
atmSvcLogCallingNumberThe calling number carried in the calling party number
information element of the call set-up message.ro AtmAddress .1.3.6.1.4.1.2.6.33.1.9.1.6.1.3 |
atmSvcLogCalledNumberThe called number carried in the called party number
information element of the call set-up message.ro AtmAddress .1.3.6.1.4.1.2.6.33.1.9.1.6.1.4 |
atmSvcLogCreationTimeThe date and time this call was placed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.9.1.6.1.5 |
atmSvcLogTimeThe date and time this call was cleared.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.9.1.6.1.6 |
atmSvcLogClearCauseThe cause of the clearing of this SVC.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.6.1.7 |
atmSvcLogForwardQOSThe forward Quality Of Service requested for this
call.ro Enumeration .1.3.6.1.4.1.2.6.33.1.9.1.6.1.8 |
atmSvcLogBackwardQOSThe backward Quality Of Service requested for this
call.ro Enumeration .1.3.6.1.4.1.2.6.33.1.9.1.6.1.9 |
atmSvcLogForwardBWThe forward bandwidth requested for this
call.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.6.1.10 |
atmSvcLogBackwardBWThe backward bandwidth requested for this
call.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.1.6.1.11 |
atmSaal OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.9.2 |
atmSaalConfTableThis table contains basic information on the SAAL protocol
for each signalling link defined per port.
Usually, there is only one signalling channel per interface
and thus one SAAL protocol definition entry per interface. SEQUENCE OF AtmSaalConfEntry .1.3.6.1.4.1.2.6.33.1.9.2.1 |
atmSaalConfEntryEntries of atmSaalConfTable. Each entry corresponds to a pair
of ATM interface, signalling channel.
A signalling channel is uniquely defined on each interface
by the VPI and VCI values allocated to it. AtmSaalConfEntry .1.3.6.1.4.1.2.6.33.1.9.2.1.1 |
atmSaalConfIndexThe ifIndex value of the ATM interface which, with the
signalling channel defined by its Vpi/Vci values,
uniquely identifies this entry.ro IfIndex .1.3.6.1.4.1.2.6.33.1.9.2.1.1.1 |
atmSaalConfSiVpiThe Vpi value which, with the Vci value specified in
atmSaalConfSiVci, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.2 |
atmSaalConfSiVciThe Vci value which, with the Vpi value specified in
atmSaalConfSiVpi, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.3 |
atmSaalStateThe state of the SAAL for this interface as defined in
the Q.2110 Specification, Chapter 7.3.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.4 |
atmSaalTimerPollTimer_POLL as defined in the Q.2110 Specification.
This timer is running in the active phase to assure that
the peer receiver is polled often enough to return
its status.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.5 |
atmSaalTimerKeepAliveTimer_KEEP-ALIVE as defined in the Q.2110 Specification.
This timer is started when entering the transient phase.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.6 |
atmSaalTimerNoResponseTimer_NO-RESPONSE as defined in the Q.2110 Specification.
This timer indicates the maximum time interval during
which at least one STAT PDU needs to be received.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.7 |
atmSaalTimerCCTimer_CC as defined in the Q.2110 Specification.
Transmission of PDUs is protected by this timer during
establishment and release of a connection and during
resynchronization or recovery.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.8 |
atmSaalTimerIdleTimer_IDLE as defined in the Q.2110 Specification.
This timer is started upon receipt of a STAT PDU
when entering the idle phase (no POLL PDUs sent).ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.9 |
atmSaalMaxCCMaxCC as defined in the Q.2110 Specification.
This is the maximum value for the state variable
VT(CC), corresponding to the maximum number of
transmissions of a BGN, END, ER or RS PDU.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.10 |
atmSaalMaxPDMaxPD as defined in the Q.2110 Specification.
This is the maximum iacceptable value for the state
variable VT(PD) before sending a POLL PDU and
resetting VT(PD) to zero.
This parameter is an upper limit for counter VT(PD)
that sends a POLL PDU after every (MaxPD) SD PDUs.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.11 |
atmSaalMaxStatMaxSTAT as defined in the Q.2110 Specification.
This is the maximum number of list elements
placed in a STAT PDU.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.1.1.12 |
atmSaalStatsTableThis table contains statistics for the SAAL protocol,
for outgoing calls only. SEQUENCE OF AtmSaalStatsEntry .1.3.6.1.4.1.2.6.33.1.9.2.2 |
atmSaalStatsEntryEntries of atmSaalConfTable. Each entry corresponds to a pair
of ATM interface, signalling channel.
A signalling channel is uniquely defined on each interface
by the VPI and VCI values allocated to it. AtmSaalStatsEntry .1.3.6.1.4.1.2.6.33.1.9.2.2.1 |
atmSaalStatsIndexThe ifIndex value of the ATM interface which, with the
signalling channel defined by its Vpi/Vci values,
uniquely identifies this entry.ro IfIndex .1.3.6.1.4.1.2.6.33.1.9.2.2.1.1 |
atmSaalStatsSiVpiThe Vpi value which, with the Vci value specified in
atmSaalStatsSiVci, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.2.1.2 |
atmSaalStatsSiVciThe Vci value which, with the Vpi value specified in
atmSaalStatsSiVpi, defines the signalling channel for this
entry.
Usually, there is one signalling channel per interface
defined by Vpi=0,Vci=5.ro INTEGER .1.3.6.1.4.1.2.6.33.1.9.2.2.1.3 |
atmSaalUnexpectPdusError conditions A to M, as defined in the Q.2110
Specification.
This is the number of received unsolicited or
or inappropriate PDUs.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.4 |
atmSaalUnsuccessPdusError condition O as defined in the Q.2110
Specification.
This is the number of failing retries.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.5 |
atmSaalFailedEstablishmentError condition P as defined in the Q.2110
Specification.
This is the number of failing polls.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.6 |
atmSaalSequenceGapThe number of times sequence gaps were
detected by the peer entity.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.7 |
atmSaalGapNumbersThe number of times frames were
re-transmitted due to sequence gaps
detected by the peer entity.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.8 |
atmSaalOtherListErrorsError conditions Q to V as defined in the
Q.2110 Specification.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.9 |
atmSaalLackOfCreditError condition W as defined in the Q.2110
Specification.
This is the number of times that transmission
was not permitted by the peer entity due to
a lack of credit.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.10 |
atmSaalCreditObtainedError condition X as defined in the Q.2110
Specification.
This is the number of times that credit was
obtained from the peer entity to allow
transmission.ro Counter .1.3.6.1.4.1.2.6.33.1.9.2.2.1.11 |
atmPvc OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.10 |
atmPvcHandlerThe status of the PVC handler in the switch.
When no more memory is available, the creation of new PVCs
is rejected with a generic Error sense code.ro Enumeration .1.3.6.1.4.1.2.6.33.1.10.1 |
atmPvcTableThis table lists all PVCs defined per interface.
There is only one entry in this table per PVC
(point-to-point or point-to-multipoint PVC). SEQUENCE OF AtmPvcEntry .1.3.6.1.4.1.2.6.33.1.10.2 |
atmPvcEntryEntries of atmPvcTable.
Policing parameters are those requested when
creating the PVC. The actual values used by the
network to satisfy these requirements may slightly
differ. These values are attached to virtual links
and are available in virtual link tables, such as
the RFC-1695 VPL/VCL tables. AtmPvcEntry .1.3.6.1.4.1.2.6.33.1.10.2.1 |
atmPvcIndexThe ifIndex value of the ATM interface used by this PVC.ro IfIndex .1.3.6.1.4.1.2.6.33.1.10.2.1.1 |
atmPvcIdentifierA value used to uniquely identify this PVC on this
interface.
To create a new PVC on a given interface, an unused PVC
identifier must be found.ro INTEGER .1.3.6.1.4.1.2.6.33.1.10.2.1.2 |
atmPvcRowStatusStates values:
active: the PVC is operational
notInService: the PVC is failing
notReady: values are missing to be able to activate this PVC
Actions:
active: this requests to re-start a failing PVC (which status
was notInService)
destroy: this requests to delete a PVC
createAndWait: this requests to create a PVC
To create a new PVC, this variable must be set to
createAndWait with an index where:
- atmPvcIndex is the number of the interface from where the
PVC is created
- atmPvcIdentifier is an unused PVC identifier for this
interface
To activate a PVC, this variable must be set to active.
Default values are provided for all attributes except for the
atmPvcEpRemIndex. If this attribute is not set, the PVC will
remain in the notReady state.
To delete a point-to-point PVC, this variable must be set to
destroy.rw Enumeration .1.3.6.1.4.1.2.6.33.1.10.2.1.3 |
atmPvcTypeA unicast PVC is defined between two endpoints, using
either a VP or a VC connection.rw Enumeration .1.3.6.1.4.1.2.6.33.1.10.2.1.4 |
atmPvcEndPointThe end-point where the PVC is created is identified as the
primary or root end-point.
the other end-point is the identified as the secondary or
leaf end-point.ro Enumeration .1.3.6.1.4.1.2.6.33.1.10.2.1.5 |
atmPvcVpiThe VPI value assigned to this PVC at the origin.
A value of 65536 means that no value has been specified by
the operator.
If no value has been specified, the VPI value is then
automatically allocated by the agent when activating the PVC.rw INTEGER .1.3.6.1.4.1.2.6.33.1.10.2.1.6 |
atmPvcVciThe VCI value assigned to this PVC at the origin.
For VP-type PVC, this value is not applicable and is
set to 0.
A value of 65536 means that no value has been specified by
the operator.
If no value has been specified, the VCI value is then
automatically allocated by the agent when activating the PVC.rw INTEGER .1.3.6.1.4.1.2.6.33.1.10.2.1.7 |
atmPvcBackwardQosThe QOS requested for this PVC to the originator.rw Enumeration .1.3.6.1.4.1.2.6.33.1.10.2.1.8 |
atmPvcForwardQosThe QOS requested for this PVC from the originator.rw Enumeration .1.3.6.1.4.1.2.6.33.1.10.2.1.9 |
atmPvcBackwardTypeThe first parameter used to define the
policy requested for this PVC.rw OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.10.2.1.10 |
atmPvcForwardTypeThe type of policy requested for this PVC.rw OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.1.10.2.1.11 |
atmPvcBackwardParm1The fourth parameter used to define the
policy requested for this PVC.rw INTEGER .1.3.6.1.4.1.2.6.33.1.10.2.1.12 |
atmPvcForwardParm1The third parameter used to define the
policy requested for this PVC.rw INTEGER .1.3.6.1.4.1.2.6.33.1.10.2.1.13 |
atmPvcEpTableThis table lists the characteristics of the remote
end-points of defined PVCs.
There is one entry for each PVC defined in the atmPvcTable. SEQUENCE OF AtmPvcEpEntry .1.3.6.1.4.1.2.6.33.1.10.3 |
atmPvcEpEntryEntries of atmPvcEpTable.
One entry is automatically created by the agent when a
PVC is created in the PVC Table.
No additional entry can be created in this table if the
PVC is defined as point-to-point in the PVC table. AtmPvcEpEntry .1.3.6.1.4.1.2.6.33.1.10.3.1 |
atmPvcEpIndexThe ifIndex value of the ATM interface used by this PVC.ro IfIndex .1.3.6.1.4.1.2.6.33.1.10.3.1.1 |
atmPvcEpIdentifierA value used to uniquely identify this PVC on this
interface.
This is the same identifier as the one used in the atmPvcTable
to identify the PVC that this end-point belongs to.ro INTEGER .1.3.6.1.4.1.2.6.33.1.10.3.1.2 |
atmPvcEpPartyA value used to uniquely identify a remote end-point of a PVC,
when associated with an interface index and a PVC identifier.
For a point-to-point PVC, this value is always set to 0.ro INTEGER .1.3.6.1.4.1.2.6.33.1.10.3.1.3 |
atmPvcEpRowStatusStates values:
active: the PVC is operational
notInService: the PVC is failing
notReady: values are missing to be able to activate this PVC
Actions:
active: this requests to re-start a failing unicast PVC
(status was notInService)
destroy: this requests to delete a unicast PVC.rw Enumeration .1.3.6.1.4.1.2.6.33.1.10.3.1.4 |
atmPvcEpStatusCauseA detailed cause for the current PVC status.ro Enumeration .1.3.6.1.4.1.2.6.33.1.10.3.1.5 |
atmPvcEpRemAddressThe ATM address of the remote ATM switch where the PVC
ends.
If none is specified, the ATM address of the target
switch (local) is used and the PVC is confined to the
target switch (local switch).rw NetPrefix .1.3.6.1.4.1.2.6.33.1.10.3.1.6 |
atmPvcEpRemIndexThe ifindex value used at the remote end to identify the
interface where the PVC ends.
This entry will remain in the notReady state until this
attribute is set (and the atmPvcRowStatus is set to active).rw IfIndex .1.3.6.1.4.1.2.6.33.1.10.3.1.7 |
atmPvcEpRemVpiThe VPI value assigned to this PVC at the destination
(remote end).
If left at 65536 (default value), one value is
automatically allocated by the agent.rw INTEGER .1.3.6.1.4.1.2.6.33.1.10.3.1.8 |
atmPvcEpRemVciThe VCI value assigned to this PVC at the destination.
For VP-type PVC, this value is not applicable and is
set to 0.
If left at 65536 (default value), one value is
automatically allocated by the agent (for VC only).rw INTEGER .1.3.6.1.4.1.2.6.33.1.10.3.1.9 |
atmPvcEpLastActiveThe date and time of the latest PVC activation.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2.6.33.1.10.3.1.10 |
atmPvcEpQ2931CauseThe cause of the failure as defined by Q2931.ro INTEGER .1.3.6.1.4.1.2.6.33.1.10.3.1.11 |
atmPvcEpFailuresThe number of times this PVC failed.ro Counter .1.3.6.1.4.1.2.6.33.1.10.3.1.12 |
agents OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.2 |
ibm8260 OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.2.1 |
gatwick OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.2.2 |
admin OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.3 |
testType OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.3.1 |
internalLoopback OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.3.1.1 |
externalLoopback OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.33.3.1.2 |