ASCEND-CALL-LOGGING-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ASCEND-CALL-LOGGING-MIB.
18
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
18 total| Object Name |
|---|
RFC1155-SMIThe maximum number of Call Logging
servers supported by the system.ro INTEGER .1.3.6.1.4.1.529.25.1 |
callLoggingServerTableA list of entries for Call Logging Server
addresses. SEQUENCE OF CallLoggingServerEntry .1.3.6.1.4.1.529.25.2 |
callLoggingServerEntryEntry holding information about the currently
active Call Logging Server and the address of
a Server. CallLoggingServerEntry .1.3.6.1.4.1.529.25.2.1 |
callLoggingServerIndexThe index number for this Call Logging server
entry. Its value ranges from 1 to
'callLoggingNumServers'. and identifies which
server entry is associated with.ro INTEGER .1.3.6.1.4.1.529.25.2.1.1 |
callLoggingCurrentServerFlagValue indicates whether this entry is the current
Call Logging server or not.ro Enumeration .1.3.6.1.4.1.529.25.2.1.2 |
callLoggingServerIPAddressThe IP address of Call Logging server. The
value 0.0.0.0 is returned if entry is invalid.rw IpAddress .1.3.6.1.4.1.529.25.2.1.3 |
callLoggingEnableActiveServerThis is used to set the active call Logging server.
If set to enable(2) it will enable the call Logging server,
A read on the variable will return notApplicable(1).rw Enumeration .1.3.6.1.4.1.529.25.2.1.4 |
callLoggingStatusEnable/Disable call loggin support.
Note: Prior to enable the call Logging, one of
the Call Logging server must be setup with a
valid IP address. If the server IP address is
not setup, a SET to this object will return with
a bad value error.rw Enumeration .1.3.6.1.4.1.529.25.3 |
callLoggingPortNumberThe UDP server port to use for Call Logging
packets.rw INTEGER ( 0.. 'FFFF'h ) .1.3.6.1.4.1.529.25.4 |
callLoggingKeyThe (RADIUS_ACCT) call logging key to access
server.rw OCTET STRING .1.3.6.1.4.1.529.25.5 |
callLoggingTimeoutNumber of seconds to wait for a response to
previous Call Logging request sent to server.rw INTEGER .1.3.6.1.4.1.529.25.6 |
callLoggingIdBaseThe Base to use in reporting Call Logging ID.rw Enumeration .1.3.6.1.4.1.529.25.7 |
callLoggingResetTimeThe time to reset to the primary server after
it has failed.rw INTEGER ( 0..'7FFFFFFF'h ) .1.3.6.1.4.1.529.25.8 |
callLoggingStopPacketsOnlySend call log Stop packets that have username=0.
These are caused by connections that are dropped
before authentication is done.rw Enumeration .1.3.6.1.4.1.529.25.9 |
callLoggingRetryLimitNumber of retries before removing Call Logging
packet. 0 means leave on retry list until maximum
retry entries are exceeded.rw INTEGER .1.3.6.1.4.1.529.25.10 |
callLoggingAssStatusIndicates the status of Active Session Snapshot
protocol.
Writing the attribute with a nonzero value causes
the start of an Active Session Snapshot. If no
server is configured the Active Session Snapshot
will abort immediatly, an active session can not
be abortedrw Enumeration .1.3.6.1.4.1.529.25.11 |
callLoggingDroppedPacketCountNumber of dropped Call Logging packets since the
last Active Session Snapshotro INTEGER .1.3.6.1.4.1.529.25.12 |
callLoggingRadCompatModeIndicates call logging RADIUS compatibility mode.
This variable is deprecated, starting with TAOS
Release 8.0. this variable has a fixed value of
radVendorSpecific(4)ro Enumeration .1.3.6.1.4.1.529.25.13 |