ALCATEL-IND1-IPV6-MIB
AI MIB Summary
The ALCATEL-IND1-IPV6-MIB provides enterprise-specific SNMP definitions for monitoring and managing IPv6 network interfaces, routing tables, neighbor discovery states, and address configuration parameters on Alcatel-Lucent hardware. It enables the collection of protocol-specific metrics such as IPv6 packet counters, error statistics, and neighbor cache entries to facilitate network troubleshooting and capacity planning.
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB):
Propietary IPv6 MIB definitions
The right to make changes in specification and other information contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used.
Copyright (C) 1995-2013 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Main OID:
alcatelIND1IPv6MIB.1.3.6.1.4.1.6486.801.1.2.1.29.1
137
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
137 total| Object Name |
|---|
alcatelIND1IPv6MIBThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
Propietary IPv6 MIB definitions
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special,
or consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE MODULE-IDENTITY .1.3.6.1.4.1.6486.801.1.2.1.29.1 |
alcatelIND1IPv6MIBNotificationsBranch For IPv6 MIB Subsystem Notifications. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.29.1.0 |
ndpMaxLimitReachedThis notification is generated when hardware table has reached supported
Maximum entries. OS6400 will not generate new ARP request for new nexthops NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.29.1.0.1 |
alaIPv6NeighborLimitExceededNotification that the system-wide neighbor cache limit
has been exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.29.1.0.2 |
alaIPv6NeighborVRFLimitExceededNotification that a per-VRF neighbor cache limit
has been exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.29.1.0.3 |
alaIPv6InterfaceNeighborLimitExceededNotification that a per-interface neighbor cache limit
has been exceeded. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.29.1.0.4 |
alcatelIND1IPv6MIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.29.1.1 |
alaIPv6Config OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1 |
alaIPv6ClearNeighborsClear all non-static entries from the Neighbor table.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.1 |
alaIPv6ClearTrafficReset all IPv6 traffic counters.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.2 |
alaIPv6ClearPMTUTableClear the path MTU table.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.3 |
alaIPv6PMTUMinLifetimeSet the minimum lifetime for entries in the
path MTU table.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.4 |
alaIPv6NeighborStaleLifetimeSet the minimum lifetime for neighbor entries in the
stale state.
In older versions of this MIB the default was specified
as 1440 minutes.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.5 |
alaIPv6GlobalIDThe global ID used in the creation of local IPv6 unicast
addresses (RFC 4193). An explicit value may be specified for
the global ID or this object may be set to all zero to have a
global ID be created based on the algorithm from the RFC.rw OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.6 |
alaIPv6VirtualSourceMACIf set to enable(1) when a packet's source address is a
VRRP virtual IPv6 address, the corresponding VRRP virtual
MAC will be used as the source L2 address.
If set to disable(2), the default, the interface's real
MAC will be used as the source L2 address.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.7 |
alaIPv6NeighborLimitThe system-wide maximum size of the neighbor cache. A value
of 0 indicates that no limit will be enforced. The minimum
value is 200 entries.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.8 |
alaIPv6NeighborVRFLimitThe maximum size of the neighbor cache for a specific VRF.
A value of 0 indicates that no limit is set. The minimum
value is 200 entries.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.9 |
alaIPv6InterfaceTableTable allowing the creation and removal of IPv6
interfaces.
The table is indexed by ipv6IfIndex. The value of
ipv6IfIndex shall be a four byte value in one of
the following formats:
0x0000vvvv - The interface for VLAN vvvv
0x0100tttt - The interface for tunnel tttt
0x02000001 - The IPv6 loopback interface
The loopback interface configuration cannot be
modified. SEQUENCE OF AlaIPv6InterfaceEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2 |
alaIPv6InterfaceEntryAn IPv6 interface entry. AlaIPv6InterfaceEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1 |
alaIPv6InterfaceRowStatusUsed to control the addition and removal of IPv6
interfaces.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.1 |
alaIPv6InterfaceDescriptionThe IPv6 interface's description.ro SnmpAdminString .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.2 |
alaIPv6InterfaceMtuThe IPv6 interface's maximum transmission unit.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.3 |
alaIPv6InterfaceTypeThe interface type.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.4 |
alaIPv6InterfaceAdminStatusInterface administrative status.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.5 |
alaIPv6InterfaceSendRouterAdvertisementsSpecify whether the router sends periodic router
advertisements and responds to router solicitations
on the interface.
The default value for most interfaces is enable(1).
Some interface types (e.g. 6to4 tunnel) cannot send
router advertisements so the default (and only)
value for those interfaces is disable(2).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.6 |
alaIPv6InterfaceMaxRtrAdvIntervalThe maximum time allowed between sending unsolicited
multicast router advertisements from the interface.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.7 |
alaIPv6InterfaceAdvManagedFlagThe TRUE/FALSE value to be placed in the 'Managed
address configuration' flag field in router advertisements.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.8 |
alaIPv6InterfaceAdvOtherConfigFlagThe TRUE/FALSE value to be placed in the 'Other stateful
configuration' flag field in router advertisements.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.9 |
alaIPv6InterfaceAdvReachableTimeThe value to be placed in the Reachable Time field in
the router advertisements sent over this interface. The
value zero means unspecified by this router.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.10 |
alaIPv6InterfaceAdvRetransTimerThe value to be placed in the Retrans Timer field in
the router advertisements sent over this interface. The
value zero means unspecified by this router.rw Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.11 |
alaIPv6InterfaceAdvDefaultLifetimeThe value to be placed in the Router Lifetime field in
the router advertisements sent over this interface.
The value MUST be either zero, 1, or between
alaIPv6InterfaceMaxRtrAdvInterval and 9000 seconds.
The special value zero indicates that the router is not
to be used as a default router.
The special value 1 indicates that this object's true
value should be computed using the formula
3 * alaIPv6InterfaceMaxRtrAdvInterval.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.12 |
alaIPv6InterfaceNameThe mandatory user-assigned name for the interface.
Since the loopback interface is created without user
interaction, the name 'loopback' will be automatically
assigned.rw SnmpAdminString .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.13 |
alaIPv6InterfaceAdvSendMtuThe TRUE/FALSE value that determines whether the MTU
option is sent in Router Advertisements.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.14 |
alaIPv6InterfaceReachableTimeIn the absence of any reachability notification, the
amount of time a neighbor reached via this interface
will remain in the reachable state before transitioning
to the stale state. Computed to be between .5 and 1.5
times the alaIPv6InterfaceBaseReachableTime.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.15 |
alaIPv6InterfaceBaseReachableTimeThe base value used to compute the reachable time
for neighbors reached via this interface. See
alaIPv6InterfaceReachableTime above.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.16 |
alaIPv6InterfaceMinRtrAdvIntervalThe minimum time allowed between sending unsolicited
multicast router advertisements from the interface.
The time must be a minimum of 3 seconds and no more than
.75 times the value of alaIPv6InterfaceMaxRtrAdvInterval.
Setting this object to the special value of 0 indicates
that the minimum interval should be automatically
recalculated using the formula .33 times the value of
alaIPv6InterfaceMaxRtrAdvInterval.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.17 |
alaIPv6InterfaceClockSkewRouter Advertisement decrementing timers must be consistent
in all Advertisements on the link. The clock skew accounts
for link propogation delays and poorly synchronized clocks.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.18 |
alaIPv6InterfaceRetransTimerThe amount of time to wait before retransmitting a Neighbor
Solicitation during neighbor discovery.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.19 |
alaIPv6InterfaceDADTransmitsThe number of Neighbor Solicitations to send during Duplicate
Address Detection.
A value of 0 indicates that DAD will not be performed for
addresses assigned to the interface.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.20 |
alaIPv6InterfaceAdvHopLimitThe value placed in the current hop limit field of router
advertisements.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.21 |
alaIPv6InterfaceLPNDEnable/disable local proxy neighbor discovery.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.22 |
alaIPv6InterfaceRAFilterEnable/disable RA filtering.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.23 |
alaIPv6InterfaceNeighborLimitThe maximum number o neighbor entries that may be cached
on this interface. A value of 0 indicates that no limit
is set. The minimum value is 10.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.24 |
alaIPv6InterfaceRetransBackoffThe neighbor unreachability detection exponential backoff base.
A value of 1 indicates the use of fixed interval retransmissions.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.25 |
alaIPv6InterfaceRetransMaxThe maximum number of neighbor solicitations to be sent during
neighbor discovery or neighbor unreachability detection.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.26 |
alaIPv6TunnelConfig OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3 |
alaIPv6ConfigTunnelTableTable for IPv6 configured tunnels. This table contains the
tunnel-specific information extending the corresponding
tunnel interface entry in alaIPv6InterfaceTable. SEQUENCE OF AlaIPv6ConfigTunnelEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2 |
alaIPv6ConfigTunnelEntryA entry contains the objects for an IPv6 configured tunnel. AlaIPv6ConfigTunnelEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1 |
alaIPv6ConfigTunnelV4SourceThe source IPv4 address for the tunnel.rw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.1 |
alaIPv6ConfigTunnelV4DestThe destination IPv4 address for the tunnel.rw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.2 |
alaIPv6InterfaceAddressTableTable allowing the creation and removal of IPv6
addresses assigned to interfaces. SEQUENCE OF AlaIPv6InterfaceAddressEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4 |
alaIPv6InterfaceAddressEntryAn IPv6 interface address entry.
The same link-local address may be assigned to
multiple interfaces. A global address may only
be assigned to a single interface. AlaIPv6InterfaceAddressEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1 |
alaIPv6InterfaceAddressRowStatusUsed to control the addition and removal of IPv6
interface addresses.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.1 |
alaIPv6InterfaceAddressAn IPv6 address (or prefix for EUI-64 addresses)
assigned to the interface. Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.2 |
alaIPv6InterfaceAddressPrefixLengthThe number of bits that are significant in the IPv6
address' prefix.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.3 |
alaIPv6InterfaceAddressAnycastFlagThis object has the value 'true(1)', if this
address is an anycast address and the value
'false(2)' otherwise.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.4 |
alaIPv6InterfaceAddressDADStatusThe status of duplicate address detection for this address.
The only value that may be set via SNMP is 'check' when the
current status is 'duplicate'. In such cases, duplicate
address detection will be performed again for the address.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.5 |
alaIPv6InterfaceEUI64AddressTableTable allowing the creation and removal of IPv6
addresses formed by appending an EUI-64 interface
identifier to the specified prefix.
This table is mainly used for the creation of such
addresses. After creation they can be managed
via the alaIPv6InterfaceAddressTable. SEQUENCE OF AlaIPv6InterfaceEUI64AddressEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5 |
alaIPv6InterfaceEUI64AddressEntryAn IPv6 interface EUI-64 address entry. AlaIPv6InterfaceEUI64AddressEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1 |
alaIPv6InterfaceEUI64AddressRowStatusUsed to control the addition and removal of IPv6
interface EUI-64 addresses.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.1 |
alaIPv6InterfaceEUI64AddressPrefixThe prefix for the EUI-64 address. AlaIPv6AddressPrefix .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.2 |
alaIPv6InterfaceEUI64AddressPrefixLengthThe number of bits that are significant in the IPv6
address' prefix.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.3 |
alaIPv6InterfaceEUI64AddressIdentifierThe interface's EUI-64 identifier which is combined
with the prefix to form the IPv6 address.ro OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.4 |
alaIPv6NeighborTableThe IPv6 neighbor table. Much of this information is
available in the RFC-2465 ipv6NetToMediaTable. However,
that table does not allow the static configuration of
neighbor entries (all objects except for
ipv6NetToMediaValid are read-only). SEQUENCE OF AlaIPv6NeighborEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6 |
alaIPv6NeighborEntryEach entry contains one IPv6 address to `physical'
address equivalence (a neighbor). AlaIPv6NeighborEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1 |
alaIPv6NeighborNetAddressThe neighbor's IPv6 Address. Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.1 |
alaIPv6NeighborPhysAddressThe neighbor's media-dependent `physical' address.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.2 |
alaIPv6NeighborSlotThe slot used to reach the neighbor. When creating a static neighbor
the slot must be specified. On read, a value of zero indicates
the slot is not known/not applicable.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.3 |
alaIPv6NeighborPortThe port used to reach the neighbor. When creating a static neighbor
the port must be specified. On read, a value of zero indicates the
port is not known/not applicable.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.4 |
alaIPv6NeighborTypeThe type of the mapping. The 'dynamic(2)' type
indicates that the IPv6 address to physical
addresses mapping has been dynamically
resolved using the IPv6 Neighbor Discovery
protocol. The static(3)' types indicates that
the mapping has been statically configured.
The local(4) indicates that the mapping is
provided for an entity's own interface address.
All entries added via this table will have the
type static(3) and only static entries may be
removed via this table.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.5 |
alaIPv6NeighborStateThe Neighbor Unreachability Detection state
for the interface when the address mapping in
this entry is used.rodeprecated Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.6 |
alaIPv6NeighborLastUpdatedThe value of sysUpTime at the time this entry
was last updated. If this entry was updated prior
to the last re-initialization of the local network
management subsystem, then this object contains
a zero value.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.7 |
alaIPv6NeighborRowStatusUsed to control the addition and removal of static
entries in the neighbor table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.8 |
alaIPv6NeighborLifetimeThe remaining time the neighbor will stay in its current
state. External events may cause a state change before
the expiry of this lifetime. A value of zero indicates
the neighbor will remain in its current state indefinitely.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.9 |
alaIPv6NeighborReachabilityThe reachability status of the neighbor.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.10 |
alaIPv6NeighborChassisOn a multi-chasis system, the chassis used to reach the neighbor.
On a single-chassis system this value is always 0. On read, a
value of zero may indicate that the chassis is not known/not
applicable.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.11 |
alaIPv6StaticRouteTableThis table has been superseded by alaIprmV6StaticRouteTable in
ALCATEL-IND1-IPRMV6-MIB.
Table allowing the creation and removal of static
IPv6 routes.obsolete SEQUENCE OF AlaIPv6StaticRouteEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7 |
alaIPv6StaticRouteEntryA static route entry.obsolete AlaIPv6StaticRouteEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1 |
alaIPv6StaticRouteDestThe destination IPv6 address of this static
route. This object may not take a Multicast
address value.obsolete Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.1 |
alaIPv6StaticRoutePfxLengthIndicates the prefix length of the destination
address.obsolete Integer32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.2 |
alaIPv6StaticRouteIfIndexIf the next hop address is a link-local
address, this is the ipv6IfIndex value of the
interface over which the destination is reached.
For all other next hop address types the value
is zero.rwobsolete Ipv6IfIndexOrZero (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.3 |
alaIPv6StaticRouteNextHopThe IPv6 address of the next hop towards the
destination.rwobsolete Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.4 |
alaIPv6StaticRouteMetricThe routing metric for this route. The lower the
value, the higher the priority for the static
route.rwobsolete Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.5 |
alaIPv6StaticRouteRowStatusUsed to control the addition and removal of static
routes.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.6 |
alaIPv6HostTableLocal table mapping host names to IPv6 addresses. This provides
the equivalent of /etc/hosts for IPv6. SEQUENCE OF AlaIPv6HostEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8 |
alaIPv6HostEntryA entry maps a host name to an IPv6 address. AlaIPv6HostEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1 |
alaIPv6HostNameA host name to be mapped to an IPv6 address. SnmpAdminString .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.1 |
alaIPv6HostAddressThe IPv6 address mapped to the host name. Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.2 |
alaIPv6HostRowStatusAllows host name/IPv6 address mappings to be created and
deleted in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.3 |
alaIPv6InterfacePrefixTableTable allowing the creation and removal of IPv6
prefixes to be placed in Prefix Information
options in Router Advertisement messages sent
from the interface.
Default: all prefixes that the router advertises
via routing protocols as being on-link for the
interface from which the advertisement is sent.
The link-local prefix is not included in the
list of advertised prefixes. SEQUENCE OF AlaIPv6InterfacePrefixEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9 |
alaIPv6InterfacePrefixEntryAn IPv6 interface prefix entry. AlaIPv6InterfacePrefixEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1 |
alaIPv6InterfacePrefixRowStatusUsed to control the addition and removal of IPv6
interface prefixes for Router ADvertisement messages.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.1 |
alaIPv6InterfacePrefixThe prefix associated with this interface. Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.2 |
alaIPv6InterfacePrefixLengthThe length of the prefix in bits. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.3 |
alaIPv6InterfacePrefixValidLifetimeThe value to be placed in the Valid
Lifetime in the Prefix Information
option, in seconds. The designated value
of 4,294,967,295 represents infinity.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.4 |
alaIPv6InterfacePrefixOnLinkFlagThe value to be placed in the on-link
flag (L-bit) field in the Prefix
Information option.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.5 |
alaIPv6InterfacePrefixPreferredLifetimeThe value to be placed in the Preferred
Lifetime in the Prefix Information
option, in seconds. The designated value
of 4,294,967,295 represents infinity.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.6 |
alaIPv6InterfacePrefixAutonomousFlagThe value to be placed in the Autonomous
Flag field in the Prefix Information
option.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.7 |
alaIPv6InterfacePrefixSourceThe source of this prefix. If configured by
management the value will be configured(3). If
determined automatically from IPv6 interface
address configuration the value will be
dynamic(2).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.8 |
alaIPv6InterfacePrefixValidLifetimeDecrementIf true, use the remaining seconds derived from
alaIPv6InterfacePrefixValidLifetime in the
Router Advertisement. If false, use the static value
alaIPv6InterfacePrefixValidLifetime.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.9 |
alaIPv6InterfacePrefixValidLifetimeExpireThe date and time when the advertised prefix Valid Lifetime
expires. To use this value,
alaIPv6InterfaceValidLifetimeDecrement must be set to true.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.10 |
alaIPv6InterfacePrefixPreferredLifetimeDecrementIf true, use the remaining seconds derived from
alaIPv6InterfacePrefixPreferredLifetime in the
Router Advertisement. If false, use the static value
alaIPv6InterfacePrefixPreferredLifetime.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.11 |
alaIPv6InterfacePrefixPreferredLifetimeExpireThe date and time when the advertised prefix Preferred Lifetime
expires. To use this value,
alaIPv6InterfacePreferredLifetimeDecrement must be set to true.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.12 |
alaIPv6PMTUTableTable allowing the retrieval of the known IPv6
path MTU value. SEQUENCE OF AlaIPv6PMTUEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10 |
alaIPv6PMTUEntryAn IPv6 path MTU entry. AlaIPv6PMTUEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1 |
alaIPv6PMTUDestThe destination address of the IPv6 path. Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.1 |
alaIPv6PMTUThe path's MTU.ro Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.2 |
alaIPv6PMTUExpireThe minimum time remaining before the PMTU entry is
removed from the table.ro Unsigned32 UNITS "minutes" .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.3 |
alaIPv6PMTUHitsThe number of times the path MTU entry has been used.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.4 |
alaIPv6PMTUUpdatesThe number of times the path MTU entry has been updated.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.5 |
alaIPv6RouteFlagsTableTable allowing the retrieval of the flags for
IPv6 route entries. SEQUENCE OF AlaIPv6RouteFlagsEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11 |
alaIPv6RouteFlagsEntryAn IPV6 route flags entry. AlaIPv6RouteFlagsEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1 |
alaIPv6RouteFlagsUpTrue if the Up (U) flag is set on the route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.1 |
alaIPv6RouteFlagsGatewayTrue if the Gateway (G) flag is set on the route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.2 |
alaIPv6RouteFlagsHostTrue if the Host (H) flag is set on the route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.3 |
alaIPv6RouteFlagsStaticTrue if the Static (S) flag is set on the route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.4 |
alaIPv6RouteFlagsCloneableTrue if the Cloneable (C) flag is set on the route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.5 |
alaIPv6RouteFlagsDiscardTrue if the Discard/Blackhole (B) flag is set on the route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.6 |
alaIPv6RouteFlagsECMPTrue if the ECMP (E) flag is set on the route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.7 |
alaIPv6RouteFlagsTransientTrue if route has not been replaced by valid route after takeover.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.8 |
alaIPv6LocalUnicastTableTable allowing the creation and removal of local IPv6
unicast addresses (RFC 4193) on an interface. SEQUENCE OF AlaIPv6LocalUnicastEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13 |
alaIPv6LocalUnicastEntryAn local unicast IPv6 address entry. AlaIPv6LocalUnicastEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1 |
alaIPv6LocalUnicastGlobalIDThe global ID portion of the local IPv6 unicast address. Leave
the value as all zero when adding a new addres to use the
alaIPv6GlobalID value. OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.1 |
alaIPv6LocalUnicastSubnetIDThe subnet ID portion of the local IPv6 unicast address. OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.2 |
alaIPv6LocalUnicastInterfaceIDThe interface identifier portion of the local IPv6 unicast
address. When alaIPv6LocalUnicastEUI64 is true(1) the value
of this object should be all zero. OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.3 |
alaIPv6LocalUnicastPrefixLengthThe number of bits that are significant in the IPv6
address prefix.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.4 |
alaIPv6LocalUnicastEUI64If true(1) the interface identifier is formed from an
automatically generated EUI-64 value.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.5 |
alaIPv6LocalUnicastRowStatusUsed to control the addition and removal of local IPv6
unicast addresses.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.6 |
alaIPv6RAFilterTrustedTableTable allowing the creation and removal of trusted ports
for an interface's RA filtering. SEQUENCE OF AlaIPv6RAFilterTrustedEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14 |
alaIPv6RAFilterTrustedEntryAn RA filter trusted port entry. AlaIPv6RAFilterTrustedEntry .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1 |
alaIPv6RAFilterTrustedChassisOn a multi-chasis system, the chassis on which the trusted
port resides. On a single-chassis system or when specifying
a link aggregation this value is always 0. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.1 |
alaIPv6RAFilterTrustedSlotThe slot on which the trusted port resides. When specifying a
link aggregation this value is always 0. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.2 |
alaIPv6RAFilterTrustedPortThe trusted port's physical port number or the id of
a link aggregation. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.3 |
alaIPv6RAFilterTrustedRowStatusUsed to control the addition and removal of an RA filter's
trusted ports.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.4 |
alcatelIND1IPv6MIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.29.1.2 |
alcatelIND1IPv6MIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.29.1.2.1 |
alcatelIND1IPv6MIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2 |