ALCATEL-IND1-QOS-MIB
AI MIB Summary
The ALCATEL-IND1-QOS-MIB enables monitoring and configuration of Quality of Service (QoS) policies, traffic shaping parameters, and access control list (ACL) filtering rules on Alcatel-Lucent network infrastructure. It provides visibility into queue depths, packet discard rates, and bandwidth allocation statistics to enforce service level agreements and traffic prioritization.
QoS and Filtering MIB
Main OID:
alaQoSMIB.1.3.6.1.4.1.6486.801.1.2.1.22.1
760
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
760 total| Object Name |
|---|
alaQoSMIBQoS and Filtering MIB MODULE-IDENTITY .1.3.6.1.4.1.6486.801.1.2.1.22.1 |
IMPORTSQoS and Filtering MIB Unknown .1.3.6.1.4.1.6486.801.1.2.1.22.1 |
alaQoSMIBObjectsBranch for QoS Managed Objects. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.22.1.1 |
alaQoSRuleTableTable of QoS Rule definitions SEQUENCE OF QoSRuleEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1 |
alaQoSRuleEntryDefinition of QoS Rule QoSRuleEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1 |
alaQoSRuleNameName of rule DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.1 |
alaQoSRuleEnabledIs this rule enabled or notrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.2 |
alaQoSRuleSourceWhat entity created the rule.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.3 |
alaQoSRulePrecedencePrecedence value for rule.
Rules are evaluated from higher precedence to lower.
If rules have equal precedence, they are evaluated in
the order they are received.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.4 |
alaQoSRuleConditionName of the condition to userw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.5 |
alaQoSRuleActionName of the action to userw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.6 |
alaQoSRuleReflexiveIndicator to tell if the rule is reflexive. Reflexive rules
allow specific return connections that would normally be denied.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.7 |
alaQoSRuleSaveIndicator to tell whether to write out the rule during
snapshot commands.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.8 |
alaQoSRuleLogIndicator to tell whether to log matches to this rule
in the QoS log.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.9 |
alaQoSRuleMatchesNumber of times this rule has been matched.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.10 |
alaQoSRuleEnforcedIs this rule currenly being enforced on the switch.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.11 |
alaQoSRuleActiveIs this rule enforcable by the switch.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.12 |
alaQoSRuleRowStatusUsed to create/delete rules according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.13 |
alaQoSRuleValidityPeriodName of the validity period to userw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.14 |
alaQoSRuleValidityPeriodStatusStatus field indicating whether there is a validity period
associated with this rulerw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.15 |
alaQoSRuleLogIntervalHow often to look for packets matching this rule when logging.
When 0 log as many as possible.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.16 |
alaQoSRuleCountTypeWhich rule statistics counters to update if not all are availablerw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.17 |
alaQoSRulePacketCountCounter for packets patching this rulero Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.18 |
alaQoSRuleByteCountCounter for bytes matching this rulero Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.19 |
alaQoSRuleExcessPacketCountCounter for packets out of bandwidth parametersro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.20 |
alaQoSRuleExcessByteCountCounter for bytes out of bandwidth parametersro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.21 |
alaQoSRuleTypeThe type of rule this is. Each bit represents the following:
0x1 = bridged
0x2 = routed
0x4 = multicastro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.22 |
alaQoSRuleTrapEventsSend SNMP trap when 'qos user-port shutdown' param or
rule having action=port-disable is matched/invoked?rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.23 |
alaQoSRuleDefaultListThis rule belongs to the default policy list.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.24 |
alaQoSRuleGreenCountCounter for the number of packets being green compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.25 |
alaQoSRuleYellowCountCounter for the number of packets being yellow compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.26 |
alaQoSRuleRedCountCounter for the number of packets being red compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.27 |
alaQoSRuleNonGreenCountCounter for the number of packets being non-green compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.28 |
alaQoSRuleNonRedCountCounter for the number of packets being non-red compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.29 |
alaQoSAppliedRuleTableTable of QoS AppliedRule definitions SEQUENCE OF QoSAppliedRuleEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2 |
alaQoSAppliedRuleEntryDefinition of QoS AppliedRule QoSAppliedRuleEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1 |
alaQoSAppliedRuleNameName of rule DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.1 |
alaQoSAppliedRuleEnabledIs this rule enabled or notro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.2 |
alaQoSAppliedRuleSourceWhat entity created the rule.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.3 |
alaQoSAppliedRulePrecedencePrecedence value for rule.
Rules are evaluated from higher precedence to lower.
If rules have equal precedence, they are evaluated in
the order they are received.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.4 |
alaQoSAppliedRuleConditionName of the condition to usero DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.5 |
alaQoSAppliedRuleActionName of the action to usero DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.6 |
alaQoSAppliedRuleReflexiveIndicator to tell if the rule is reflexive. Reflexive rules
allow specific return connections that would normally be denied.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.7 |
alaQoSAppliedRuleSaveIndicator to tell whether to write out the rule during
snapshot commands.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.8 |
alaQoSAppliedRuleLogIndicator to tell whether to log matches to this rule
in the QoS log.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.9 |
alaQoSAppliedRuleMatchesNumber of times this rule has been matched.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.10 |
alaQoSAppliedRuleEnforcedIs this rule currenly being enforced on the switch.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.11 |
alaQoSAppliedRuleActiveIs this rule enforcable by the switch.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.12 |
alaQoSAppliedRuleRowStatusUsed to create/delete rules according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.13 |
alaQoSAppliedRuleValidityPeriodName of the validity period to usero DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.14 |
alaQoSAppliedRuleValidityPeriodStatusStatus field indicating whether there is a validity period
associated with this rulero Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.15 |
alaQoSAppliedRuleLogIntervalHow often to look for packets matching this rule when logging.
When 0 log as many as possible.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.16 |
alaQoSAppliedRuleCountTypeWhich rule statistics counters to update if not all are availablero Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.17 |
alaQoSAppliedRulePacketCountCounter for packets patching this rulero Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.18 |
alaQoSAppliedRuleByteCountCounter for bytes matching this rulero Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.19 |
alaQoSAppliedRuleExcessPacketCountCounter for packets out of bandwidth parametersro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.20 |
alaQoSAppliedRuleExcessByteCountCounter for bytes out of bandwidth parametersro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.21 |
alaQoSAppliedRuleTypeThe type of rule this is. Each bit represents the following:
0x1 = bridged
0x2 = routed
0x4 = multicastro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.22 |
alaQoSAppliedRuleTrapEventsSend SNMP trap when 'qos user-port shutdown' param or
rule having action=port-disable is matched/invoked?rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.23 |
alaQoSAppliedRuleDefaultListThis rule belongs to the default policy list.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.24 |
alaQoSAppliedRuleGreenCountCounter for the number of packets being green compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.25 |
alaQoSAppliedRuleYellowCountCounter for the number of packets being yellow compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.26 |
alaQoSAppliedRuleRedCountCounter for the number of packets being red compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.27 |
alaQoSAppliedRuleNonGreenCountCounter for the number of packets being non-green compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.28 |
alaQoSAppliedRuleNonRedCountCounter for the number of packets being non-red compliant.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.29 |
alaQoSConditionTableTable of QoS Condition definitions SEQUENCE OF QoSConditionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3 |
alaQoSConditionEntryDefinition of QoS Condition QoSConditionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1 |
alaQoSConditionNameName of condition DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.1 |
alaQoSConditionSourceWhat entity created the condition.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.2 |
alaQoSConditionSourceSlotSource physical slot used for traffic classification
When 0, the port identifies an aggregaterw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.3 |
alaQoSConditionSourceSlotStatusStatus field indicating whether the source physical slot and
port range needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.4 |
alaQoSConditionSourcePortSource physical port range start to use for
traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.5 |
alaQoSConditionSourcePortGroupSource physical port group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.6 |
alaQoSConditionSourcePortGroupStatusStatus field indicating whether the source physical port group
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.7 |
alaQoSConditionDestinationSlotDestination physical slot used for traffic classification
When 0, the port identifies an aggregaterw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.8 |
alaQoSConditionDestinationSlotStatusStatus field indicating whether the destination physical slot
and port range needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.9 |
alaQoSConditionDestinationPortDestination physical port range start to use for traffic
classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.10 |
alaQoSConditionDestinationPortGroupDestination physical port group to use for traffic
classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.11 |
alaQoSConditionDestinationPortGroupStatusStatus field indicating whether the destination physical port
group needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.12 |
alaQoSConditionSourceInterfaceTypeSource physical interface type to use for traffic
classificationrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.13 |
alaQoSConditionSourceInterfaceTypeStatusStatus field indicating whether the source physical
interface type needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.14 |
alaQoSConditionDestinationInterfaceTypeDestination physical interface type to use for traffic
classificationrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.15 |
alaQoSConditionDestinationInterfaceTypeStatusStatus field indicating whether the destination physical
interface type needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.16 |
alaQoSConditionSourceMacAddrSource MAC address to use for traffic classificationrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.17 |
alaQoSConditionSourceMacAddrStatusStatus field indicating whether the source MAC address & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.18 |
alaQoSConditionSourceMacMaskSource MAC mask to use for traffic classificationrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.19 |
alaQoSConditionSourceMacGroupSource MAC group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.20 |
alaQoSConditionSourceMacGroupStatusStatus field indicating whether the source MAC group
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.21 |
alaQoSConditionDestinationMacAddrDestination MAC address to use for traffic classificationrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.22 |
alaQoSConditionDestinationMacAddrStatusStatus field indicating whether the destination MAC address
& mask needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.23 |
alaQoSConditionDestinationMacMaskDestination MAC mask to use for traffic classificationrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.24 |
alaQoSConditionDestinationMacGroupDestination MAC group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.25 |
alaQoSConditionDestinationMacGroupStatusStatus field indicating whether the destination MAC group
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.26 |
alaQoSConditionSourceVlanSource VLAN to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.27 |
alaQoSConditionSourceVlanStatusStatus field indicating whether the source VLAN
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.28 |
alaQoSConditionDestinationVlanDestination VLAN to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.29 |
alaQoSConditionDestinationVlanStatusStatus field indicating whether the destination VLAN
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.30 |
alaQoSCondition8021p802.1p value to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.31 |
alaQoSCondition8021pStatusStatus field indicating whether the 802.1p value
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.32 |
alaQoSConditionSourceIpAddrSource IP address to use for traffic classificationrw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.33 |
alaQoSConditionSourceIpAddrStatusStatus field indicating whether the source IP address & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.34 |
alaQoSConditionSourceIpMaskSource IP mask to use for traffic classificationrw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.35 |
alaQoSConditionSourceNetworkGroupSource network group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.36 |
alaQoSConditionSourceNetworkGroupStatusStatus field indicating whether the source network group
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.37 |
alaQoSConditionDestinationIpAddrDestination IP address to use for traffic classificationrw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.38 |
alaQoSConditionDestinationIpAddrStatusStatus field indicating whether the destination IP address
& mask needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.39 |
alaQoSConditionDestinationIpMaskDestination IP mask to use for traffic classificationrw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.40 |
alaQoSConditionDestinationNetworkGroupDestination network group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.41 |
alaQoSConditionDestinationNetworkGroupStatusStatus field indicating whether the destination network group
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.42 |
alaQoSConditionMulticastIpAddrMulticast IP address to use for traffic classificationrw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.43 |
alaQoSConditionMulticastIpAddrStatusStatus field indicating whether the multicast IP address & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.44 |
alaQoSConditionMulticastIpMaskMulticast IP mask to use for traffic classificationrw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.45 |
alaQoSConditionMulticastNetworkGroupMulticast network group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.46 |
alaQoSConditionMulticastNetworkGroupStatusStatus field indicating whether the multicast network group
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.47 |
alaQoSConditionTosTOS value to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.48 |
alaQoSConditionTosStatusStatus field indicating whether the TOS value & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.49 |
alaQoSConditionTosMaskTOS mask to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.50 |
alaQoSConditionDscpDSCP value to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.51 |
alaQoSConditionDscpStatusStatus field indicating whether the DSCP value & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.52 |
alaQoSConditionDscpMaskDSCP mask to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.53 |
alaQoSConditionIpProtocolIP protocol to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.54 |
alaQoSConditionIpProtocolStatusStatus field indicating whether the IP protocol
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.55 |
alaQoSConditionSourceIpPortSource IP port range start to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.56 |
alaQoSConditionSourceIpPortStatusStatus field indicating whether the source IP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.57 |
alaQoSConditionDestinationIpPortDestination IP port range start to use for traffic
classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.58 |
alaQoSConditionDestinationIpPortStatusStatus field indicating whether the destination IP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.59 |
alaQoSConditionServiceName of service to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.60 |
alaQoSConditionServiceStatusStatus field indicating whether the service
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.61 |
alaQoSConditionServiceGroupName of service group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.62 |
alaQoSConditionServiceGroupStatusStatus field indicating whether the service group
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.63 |
alaQoSConditionIcmpTypeICMP type to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.64 |
alaQoSConditionIcmpTypeStatusStatus field indicating whether the ICMP type
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.65 |
alaQoSConditionIcmpCodeICMP code to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.66 |
alaQoSConditionIcmpCodeStatusStatus field indicating whether the ICMP code
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.67 |
alaQoSConditionDlciDLCI to use to traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.68 |
alaQoSConditionDlciStatusStatus field indicating whether the DLCI
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.69 |
alaQoSConditionRowStatusUsed to create/delete conditions according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.70 |
alaQoSConditionSourcePortEndSource physical port range end to use for traffic
classification. Must be greater than port range start to
indicate a range. When '1', use source port as a single port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.71 |
alaQoSConditionDestinationPortEndDestination physical port range end to use for traffic
classification. Must be greater than port range start to
indicate a range. When '1', use destination port as a single
port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.72 |
alaQoSConditionSourceIpPortEndSource IP port range end to use for traffic classification.
Must be greater than source IP port range start to indicate a
range. When '0', use source IP port as a single IP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.73 |
alaQoSConditionDestinationIpPortEndDestination IP port range end to use for traffic classification.
Must be greater than destination IP port range start to indicate
a range. When '0', use destination IP port as a single IP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.74 |
alaQoSConditionSourceTcpPortSource TCP port range start to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.75 |
alaQoSConditionSourceTcpPortStatusStatus field indicating whether the source TCP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.76 |
alaQoSConditionSourceTcpPortEndSource TCP port range end to use for traffic classification.
Must be greater than source TCP port range start to indicate a
range. When '0', use source TCP port as a single TCP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.77 |
alaQoSConditionDestinationTcpPortDestination TCP port range start to use for traffic
classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.78 |
alaQoSConditionDestinationTcpPortStatusStatus field indicating whether the destination TCP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.79 |
alaQoSConditionDestinationTcpPortEndDestination TCP port range end to use for traffic
classification. Must be greater than destination TCP port range
start to indicate a range. When '0', use destination TCP port
as a single TCP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.80 |
alaQoSConditionSourceUdpPortSource UDP port range start to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.81 |
alaQoSConditionSourceUdpPortStatusStatus field indicating whether the source UDP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.82 |
alaQoSConditionSourceUdpPortEndSource UDP port range end to use for traffic classification.
Must be greater than source UDP port range start to indicate
a range. When '0', use source UDP port as a single UDP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.83 |
alaQoSConditionDestinationUdpPortDestination UDP port range start to use for traffic
classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.84 |
alaQoSConditionDestinationUdpPortStatusStatus field indicating whether the destination UDP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.85 |
alaQoSConditionDestinationUdpPortEndDestination UDP port range end to use for traffic
classification. Must be greater than destination UDP port range
start to indicate a range. When '0', use destination UDP port
as a single TCP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.86 |
alaQoSConditionEthertypeEthertype value to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.87 |
alaQoSConditionEthertypeStatusStatus field indicating whether the ethertype value
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.88 |
alaQoSConditionTcpFlagsUse any/all specifieid TCP flags for traffic classificationrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.89 |
alaQoSConditionTcpFlagsStatusStatus field indicating whether the TCP flag bits
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.90 |
alaQoSConditionTcpFlagsValTCP flags values used for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.91 |
alaQoSConditionTcpFlagsValStatusNot usedrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.92 |
alaQoSConditionTcpFlagsMaskMask of TCP flags bits used for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.93 |
alaQoSConditionTcpFlagsMaskStatusNot usedrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.94 |
alaQoSConditionTcpEstablishedLook for established TCP sessions in classificationrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.95 |
alaQoSConditionSourceIpv6AddrSource IPv6 address to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.96 |
alaQoSConditionSourceIpv6AddrStatusStatus field indicating whether the source IPv6 address & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.97 |
alaQoSConditionSourceIpv6MaskSource IPv6 mask to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.98 |
alaQoSConditionDestinationIpv6AddrDestination IPv6 address to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.99 |
alaQoSConditionDestinationIpv6AddrStatusStatus field indicating whether the destination IPv6 address & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.100 |
alaQoSConditionDestinationIpv6MaskDestination IPv6 mask to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.101 |
alaQoSConditionIpv6Trafficclassify IPV6 trafficrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.102 |
alaQoSConditionIpv6NHNH value to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.103 |
alaQoSConditionIpv6NHStatusStatus field indicating whether the NH value
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.104 |
alaQoSConditionIpv6FlowLabelFL value to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.105 |
alaQoSConditionIpv6FlowLabelStatusStatus field indicating whether the flow label value
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.106 |
alaQoSConditionMcastIpv6AddrMulticast IPv6 address to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.107 |
alaQoSConditionMcastIpv6AddrStatusStatus field indicating whether the multicast IPv6 address & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.108 |
alaQoSConditionMcastIpv6MaskMulticast IPv6 mask to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.109 |
alaQoSConditionDscpEndDSCP value to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.110 |
alaQoSConditionInnerSourceVlanCustomer VLAN to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.111 |
alaQoSConditionInnerSourceVlanStatusStatus field indicating whether the inner VLAN
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.112 |
alaQoSConditionInner8021pCustomer 802.1p to use for traffic classificationrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.113 |
alaQoSConditionInner8021pStatusStatus field indicating whether the inner 802.1p
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.114 |
alaQoSConditionVrfNameName of Vrf to match traffic inrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.115 |
alaQoSConditionVrfNameStatusStatus field indicating whether the traffic from a specific vrf needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.116 |
alaQoSCondition8021pEnd802.1p range end value to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.117 |
alaQoSConditionInner8021pEndInner 802.1p range end value to use for traffic
classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.118 |
alaQoSConditionSourceVlanGroupSource vlan group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.119 |
alaQoSConditionSourceVlanGroupStatusStatus field indicating whether to use for traffic
classification (enabled) or not (disabled) for source
vlan group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.120 |
alaQoSConditionInnerSourceVlanGroupInner Source vlan group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.121 |
alaQoSConditionInnerSourceVlanGroupStatusStatus field indicating whether to use for traffic
classification (enabled) or not (disabled) for inner
source vlan group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.122 |
alaQoSAppliedConditionTableTable of QoS AppliedCondition definitions SEQUENCE OF QoSAppliedConditionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4 |
alaQoSAppliedConditionEntryDefinition of QoS AppliedCondition QoSAppliedConditionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1 |
alaQoSAppliedConditionNameName of condition DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.1 |
alaQoSAppliedConditionSourceWhat entity created the condition.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.2 |
alaQoSAppliedConditionSourceSlotSource physical slot used for traffic classification
When 0, the port identifies an aggregatero Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.3 |
alaQoSAppliedConditionSourceSlotStatusStatus field indicating whether the source physical slot and
port range needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.4 |
alaQoSAppliedConditionSourcePortSource physical port range start to use for
traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.5 |
alaQoSAppliedConditionSourcePortGroupSource physical port group to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.6 |
alaQoSAppliedConditionSourcePortGroupStatusStatus field indicating whether the source physical port group
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.7 |
alaQoSAppliedConditionDestinationSlotDestination physical slot used for traffic classification
When 0, the port identifies an aggregatero Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.8 |
alaQoSAppliedConditionDestinationSlotStatusStatus field indicating whether the destination physical slot
and port range needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.9 |
alaQoSAppliedConditionDestinationPortDestination physical port range start to use for traffic
classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.10 |
alaQoSAppliedConditionDestinationPortGroupDestination physical port group to use for traffic
classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.11 |
alaQoSAppliedConditionDestinationPortGroupStatusStatus field indicating whether the destination physical port
group needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.12 |
alaQoSAppliedConditionSourceInterfaceTypeSource physical interface type to use for traffic
classificationro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.13 |
alaQoSAppliedConditionSourceInterfaceTypeStatusStatus field indicating whether the source physical
interface type needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.14 |
alaQoSAppliedConditionDestinationInterfaceTypeDestination physical interface type to use for traffic
classificationro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.15 |
alaQoSAppliedConditionDestinationInterfaceTypeStatusStatus field indicating whether the destination physical
interface type needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.16 |
alaQoSAppliedConditionSourceMacAddrSource MAC address to use for traffic classificationro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.17 |
alaQoSAppliedConditionSourceMacAddrStatusStatus field indicating whether the source MAC address & mask
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.18 |
alaQoSAppliedConditionSourceMacMaskSource MAC mask to use for traffic classificationro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.19 |
alaQoSAppliedConditionSourceMacGroupSource MAC group to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.20 |
alaQoSAppliedConditionSourceMacGroupStatusStatus field indicating whether the source MAC group
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.21 |
alaQoSAppliedConditionDestinationMacAddrDestination MAC address to use for traffic classificationro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.22 |
alaQoSAppliedConditionDestinationMacAddrStatusStatus field indicating whether the destination MAC address
& mask needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.23 |
alaQoSAppliedConditionDestinationMacMaskDestination MAC mask to use for traffic classificationro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.24 |
alaQoSAppliedConditionDestinationMacGroupDestination MAC group to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.25 |
alaQoSAppliedConditionDestinationMacGroupStatusStatus field indicating whether the destination MAC group
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.26 |
alaQoSAppliedConditionSourceVlanSource VLAN to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.27 |
alaQoSAppliedConditionSourceVlanStatusStatus field indicating whether the source VLAN
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.28 |
alaQoSAppliedConditionDestinationVlanDestination VLAN to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.29 |
alaQoSAppliedConditionDestinationVlanStatusStatus field indicating whether the destination VLAN
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.30 |
alaQoSAppliedCondition8021p802.1p value to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.31 |
alaQoSAppliedCondition8021pStatusStatus field indicating whether the 802.1p value
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.32 |
alaQoSAppliedConditionSourceIpAddrSource IP address to use for traffic classificationro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.33 |
alaQoSAppliedConditionSourceIpAddrStatusStatus field indicating whether the source IP address & mask
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.34 |
alaQoSAppliedConditionSourceIpMaskSource IP mask to use for traffic classificationro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.35 |
alaQoSAppliedConditionSourceNetworkGroupSource network group to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.36 |
alaQoSAppliedConditionSourceNetworkGroupStatusStatus field indicating whether the source network group
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.37 |
alaQoSAppliedConditionDestinationIpAddrDestination IP address to use for traffic classificationro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.38 |
alaQoSAppliedConditionDestinationIpAddrStatusStatus field indicating whether the destination IP address
& mask needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.39 |
alaQoSAppliedConditionDestinationIpMaskDestination IP mask to use for traffic classificationro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.40 |
alaQoSAppliedConditionDestinationNetworkGroupDestination network group to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.41 |
alaQoSAppliedConditionDestinationNetworkGroupStatusStatus field indicating whether the destination network group
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.42 |
alaQoSAppliedConditionMulticastIpAddrMulticast IP address to use for traffic classificationro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.43 |
alaQoSAppliedConditionMulticastIpAddrStatusStatus field indicating whether the multicast IP address & mask
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.44 |
alaQoSAppliedConditionMulticastIpMaskMulticast IP mask to use for traffic classificationro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.45 |
alaQoSAppliedConditionMulticastNetworkGroupMulticast network group to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.46 |
alaQoSAppliedConditionMulticastNetworkGroupStatusStatus field indicating whether the multicast network group
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.47 |
alaQoSAppliedConditionTosTOS value to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.48 |
alaQoSAppliedConditionTosStatusStatus field indicating whether the TOS value & mask
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.49 |
alaQoSAppliedConditionTosMaskTOS mask to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.50 |
alaQoSAppliedConditionDscpDSCP value to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.51 |
alaQoSAppliedConditionDscpStatusStatus field indicating whether the DSCP value & mask
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.52 |
alaQoSAppliedConditionDscpMaskDSCP mask to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.53 |
alaQoSAppliedConditionIpProtocolIP protocol to use for traffic classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.54 |
alaQoSAppliedConditionIpProtocolStatusStatus field indicating whether the IP protocol
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.55 |
alaQoSAppliedConditionSourceIpPortSource IP port range start to use for traffic classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.56 |
alaQoSAppliedConditionSourceIpPortStatusStatus field indicating whether the source IP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.57 |
alaQoSAppliedConditionDestinationIpPortDestination IP port range start to use for traffic
classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.58 |
alaQoSAppliedConditionDestinationIpPortStatusStatus field indicating whether the destination IP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.59 |
alaQoSAppliedConditionServiceName of service to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.60 |
alaQoSAppliedConditionServiceStatusStatus field indicating whether the service
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.61 |
alaQoSAppliedConditionServiceGroupName of service group to use for traffic classificationro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.62 |
alaQoSAppliedConditionServiceGroupStatusStatus field indicating whether the service group
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.63 |
alaQoSAppliedConditionIcmpTypeICMP type to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.64 |
alaQoSAppliedConditionIcmpTypeStatusStatus field indicating whether the ICMP type
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.65 |
alaQoSAppliedConditionIcmpCodeICMP code to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.66 |
alaQoSAppliedConditionIcmpCodeStatusStatus field indicating whether the ICMP code
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.67 |
alaQoSAppliedConditionDlciDLCI to use to traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.68 |
alaQoSAppliedConditionDlciStatusStatus field indicating whether the DLCI
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.69 |
alaQoSAppliedConditionRowStatusUsed to create/delete conditions according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.70 |
alaQoSAppliedConditionSourcePortEndSource physical port range end to use for traffic
classification. Must be greater than port range start to
indicate a range. When '1', use source port as a single port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.71 |
alaQoSAppliedConditionDestinationPortEndDestination physical port range end to use for traffic
classification. Must be greater than port range start to
indicate a range. When '1', use destination port as a single
port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.72 |
alaQoSAppliedConditionSourceIpPortEndSource IP port range end to use for traffic classification.
Must be greater than source IP port range start to indicate a
range. When '0', use source IP port as a single IP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.73 |
alaQoSAppliedConditionDestinationIpPortEndDestination IP port range end to use for traffic classification.
Must be greater than destination IP port range start to indicate
a range. When '0', use destination IP port as a single IP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.74 |
alaQoSAppliedConditionSourceTcpPortSource TCP port range start to use for traffic classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.75 |
alaQoSAppliedConditionSourceTcpPortStatusStatus field indicating whether the source TCP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.76 |
alaQoSAppliedConditionSourceTcpPortEndSource TCP port range end to use for traffic classification.
Must be greater than source TCP port range start to indicate a
range. When '0', use source TCP port as a single TCP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.77 |
alaQoSAppliedConditionDestinationTcpPortDestination TCP port range start to use for traffic
classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.78 |
alaQoSAppliedConditionDestinationTcpPortStatusStatus field indicating whether the destination TCP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.79 |
alaQoSAppliedConditionDestinationTcpPortEndDestination TCP port range end to use for traffic
classification. Must be greater than destination TCP port range
start to indicate a range. When '0', use destination TCP port
as a single TCP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.80 |
alaQoSAppliedConditionSourceUdpPortSource UDP port range start to use for traffic classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.81 |
alaQoSAppliedConditionSourceUdpPortStatusStatus field indicating whether the source UDP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.82 |
alaQoSAppliedConditionSourceUdpPortEndSource UDP port range end to use for traffic classification.
Must be greater than source UDP port range start to indicate
a range. When '0', use source UDP port as a single UDP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.83 |
alaQoSAppliedConditionDestinationUdpPortDestination UDP port range start to use for traffic
classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.84 |
alaQoSAppliedConditionDestinationUdpPortStatusStatus field indicating whether the destination UDP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.85 |
alaQoSAppliedConditionDestinationUdpPortEndDestination UDP port range end to use for traffic
classification. Must be greater than destination UDP port range
start to indicate a range. When '0', use destination UDP port
as a single TCP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.86 |
alaQoSAppliedConditionEthertypeEthertype value to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.87 |
alaQoSAppliedConditionEthertypeStatusStatus field indicating whether the ethertype value
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.88 |
alaQoSAppliedConditionTcpFlagsUse any/all specifieid TCP flags for traffic classificationro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.89 |
alaQoSAppliedConditionTcpFlagsStatusStatus field indicating whether the TCP flag bits
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.90 |
alaQoSAppliedConditionTcpFlagsValTCP flags values used for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.91 |
alaQoSAppliedConditionTcpFlagsValStatusNot usedro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.92 |
alaQoSAppliedConditionTcpFlagsMaskMask of TCP flags bits used for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.93 |
alaQoSAppliedConditionTcpFlagsMaskStatusNot usedro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.94 |
alaQoSAppliedConditionTcpEstablishedLook for established TCP sessions in classificationro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.95 |
alaQoSAppliedConditionSourceIpv6AddrSource IPv6 address to use for traffic classificationro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.96 |
alaQoSAppliedConditionSourceIpv6AddrStatusStatus field indicating whether the source IPv6 address & mask
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.97 |
alaQoSAppliedConditionSourceIpv6MaskSource IPv6 mask to use for traffic classificationro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.98 |
alaQoSAppliedConditionDestinationIpv6AddrDestination IPv6 address to use for traffic classificationro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.99 |
alaQoSAppliedConditionDestinationIpv6AddrStatusStatus field indicating whether the destination IPv6 address & mask
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.100 |
alaQoSAppliedConditionDestinationIpv6MaskDestination IPv6 mask to use for traffic classificationro Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.101 |
alaQoSAppliedConditionIpv6Trafficclassify IPV6 trafficro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.102 |
alaQoSAppliedConditionIpv6NHNH value to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.103 |
alaQoSAppliedConditionIpv6NHStatusStatus field indicating whether the NH value
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.104 |
alaQoSAppliedConditionIpv6FlowLabelFL value to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.105 |
alaQoSAppliedConditionIpv6FlowLabelStatusStatus field indicating whether the flow label value
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.106 |
alaQoSAppliedConditionMcastIpv6AddrMulticast IPv6 address to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.107 |
alaQoSAppliedConditionMcastIpv6AddrStatusStatus field indicating whether the multicast IPv6 address & mask
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.108 |
alaQoSAppliedConditionMcastIpv6MaskMulticast IPv6 mask to use for traffic classificationrw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.109 |
alaQoSAppliedConditionDscpEndDSCP value to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.110 |
alaQoSAppliedConditionInnerSourceVlanCustomer VLAN to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.111 |
alaQoSAppliedConditionInnerSourceVlanStatusStatus field indicating whether the inner VLAN
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.112 |
alaQoSAppliedConditionInner8021pCustomer 802.1p to use for traffic classificationro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.113 |
alaQoSAppliedConditionInner8021pStatusStatus field indicating whether the inner 802.1p
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.114 |
alaQoSAppliedConditionVrfNameName of Vrf to match traffic inrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.115 |
alaQoSAppliedConditionVrfNameStatusStatus field indicating whether the traffic from a specific vrf needs
to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.116 |
alaQoSAppliedCondition8021pEnd802.1p range end value to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.117 |
alaQoSAppliedConditionInner8021pEndInner 802.1p range end value to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.118 |
alaQoSAppliedConditionSourceVlanGroupSource vlan group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.119 |
alaQoSAppliedConditionSourceVlanGroupStatusStatus field indicating whether to use for traffic
classification (enabled) or not (disabled) for source
vlan group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.120 |
alaQoSAppliedConditionInnerSourceVlanGroupInner Source vlan group to use for traffic classificationrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.121 |
alaQoSAppliedConditionInnerSourceVlanGroupStatusStatus field indicating whether to use for traffic
classification (enabled) or not (disabled) for inner
source vlan group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.122 |
alaQoSServiceTableTable of QoS Service definitions SEQUENCE OF QoSServiceEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5 |
alaQoSServiceEntryDefinition of QoS Service QoSServiceEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1 |
alaQoSServiceNameName of the service DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.1 |
alaQoSServiceSourceWhat entity created the service.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.2 |
alaQoSServiceProtocolprotocol field for Servicerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.3 |
alaQoSServiceSourceIpPortSource IP port range start to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.4 |
alaQoSServiceSourceIpPortStatusStatus field indicating whether the source IP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.5 |
alaQoSServiceDestinationIpPortDestination IP port range start to use for traffic
classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.6 |
alaQoSServiceDestinationIpPortStatusStatus field indicating whether the destination IP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.7 |
alaQoSServiceRowStatusUsed to create/delete services according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.8 |
alaQoSServiceSourceIpPortEndSource IP port range end to use for traffic classification.
Must be greater than source IP port range start to indicate
a range. When '0', use source IP port as a single IP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.9 |
alaQoSServiceDestinationIpPortEndDestination IP port range end to use for traffic classification.
Must be greater than destination IP port range start to indicate
a range. When '0', use destination IP port as a single IP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.10 |
alaQoSServiceSourceTcpPortSource TCP port range start to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.11 |
alaQoSServiceSourceTcpPortStatusStatus field indicating whether the source TCP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.12 |
alaQoSServiceSourceTcpPortEndSource TCP port range end to use for traffic classification.
Must be greater than source TCP port range start to indicate a
range. When '0', use source TCP port as a single TCP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.13 |
alaQoSServiceDestinationTcpPortDestination TCP port range start to use for traffic
classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.14 |
alaQoSServiceDestinationTcpPortStatusStatus field indicating whether the destination TCP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.15 |
alaQoSServiceDestinationTcpPortEndDestination TCP port range end to use for traffic
classification. Must be greater than destination TCP port range
start to indicate a range. When '0', use destination TCP port as
a single TCP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.16 |
alaQoSServiceSourceUdpPortSource UDP port range start to use for traffic classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.17 |
alaQoSServiceSourceUdpPortStatusStatus field indicating whether the source UDP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.18 |
alaQoSServiceSourceUdpPortEndSource UDP port range end to use for traffic classification.
Must be greater than source UDP port range start to indicate a
range. When '0', use source UDP port as a single UDP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.19 |
alaQoSServiceDestinationUdpPortDestination UDP port range start to use for traffic
classification.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.20 |
alaQoSServiceDestinationUdpPortStatusStatus field indicating whether the destination UDP port range
needs to be matched(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.21 |
alaQoSServiceDestinationUdpPortEndDestination UDP port range end to use for traffic
classification. Must be greater than destination UDP port range
start to indicate a range. When '0', use destination UDP port as
a single UDP port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.22 |
alaQoSAppliedServiceTableTable of QoS AppliedService definitions SEQUENCE OF QoSAppliedServiceEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6 |
alaQoSAppliedServiceEntryDefinition of QoS AppliedService QoSAppliedServiceEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1 |
alaQoSAppliedServiceNameName of the service DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.1 |
alaQoSAppliedServiceSourceWhat entity created the service.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.2 |
alaQoSAppliedServiceProtocolprotocol field for AppliedServicero Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.3 |
alaQoSAppliedServiceSourceIpPortSource IP port range start to use for traffic classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.4 |
alaQoSAppliedServiceSourceIpPortStatusStatus field indicating whether the source IP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.5 |
alaQoSAppliedServiceDestinationIpPortDestination IP port range start to use for traffic
classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.6 |
alaQoSAppliedServiceDestinationIpPortStatusStatus field indicating whether the destination IP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.7 |
alaQoSAppliedServiceRowStatusUsed to create/delete services according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.8 |
alaQoSAppliedServiceSourceIpPortEndSource IP port range end to use for traffic classification.
Must be greater than source IP port range start to indicate
a range. When '0', use source IP port as a single IP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.9 |
alaQoSAppliedServiceDestinationIpPortEndDestination IP port range end to use for traffic classification.
Must be greater than destination IP port range start to indicate
a range. When '0', use destination IP port as a single IP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.10 |
alaQoSAppliedServiceSourceTcpPortSource TCP port range start to use for traffic classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.11 |
alaQoSAppliedServiceSourceTcpPortStatusStatus field indicating whether the source TCP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.12 |
alaQoSAppliedServiceSourceTcpPortEndSource TCP port range end to use for traffic classification.
Must be greater than source TCP port range start to indicate a
range. When '0', use source TCP port as a single TCP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.13 |
alaQoSAppliedServiceDestinationTcpPortDestination TCP port range start to use for traffic
classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.14 |
alaQoSAppliedServiceDestinationTcpPortStatusStatus field indicating whether the destination TCP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.15 |
alaQoSAppliedServiceDestinationTcpPortEndDestination TCP port range end to use for traffic
classification. Must be greater than destination TCP port range
start to indicate a range. When '0', use destination TCP port as
a single TCP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.16 |
alaQoSAppliedServiceSourceUdpPortSource UDP port range start to use for traffic classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.17 |
alaQoSAppliedServiceSourceUdpPortStatusStatus field indicating whether the source UDP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.18 |
alaQoSAppliedServiceSourceUdpPortEndSource UDP port range end to use for traffic classification.
Must be greater than source UDP port range start to indicate a
range. When '0', use source UDP port as a single UDP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.19 |
alaQoSAppliedServiceDestinationUdpPortDestination UDP port range start to use for traffic
classification.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.20 |
alaQoSAppliedServiceDestinationUdpPortStatusStatus field indicating whether the destination UDP port range
needs to be matched(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.21 |
alaQoSAppliedServiceDestinationUdpPortEndDestination UDP port range end to use for traffic
classification. Must be greater than destination UDP port range
start to indicate a range. When '0', use destination UDP port as
a single UDP port.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.22 |
alaQoSServiceGroupsTableTable of QoS ServiceGroups definitions SEQUENCE OF QoSServiceGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7 |
alaQoSServiceGroupsEntryDefinition of QoS ServiceGroups QoSServiceGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1 |
alaQoSServiceGroupsNameName of service group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1.1 |
alaQoSServiceGroupsSourceWhat entity created the service group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1.2 |
alaQoSServiceGroupsStatusUsed to create/delete service groups according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1.3 |
alaQoSAppliedServiceGroupsTableTable of QoS AppliedServiceGroups definitions SEQUENCE OF QoSAppliedServiceGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8 |
alaQoSAppliedServiceGroupsEntryDefinition of QoS AppliedServiceGroups QoSAppliedServiceGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1 |
alaQoSAppliedServiceGroupsNameName of service group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1.1 |
alaQoSAppliedServiceGroupsSourceWhat entity created the service group.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1.2 |
alaQoSAppliedServiceGroupsStatusUsed to create/delete service groups according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1.3 |
alaQoSServiceGroupTableTable of QoS ServiceGroup definitions SEQUENCE OF QoSServiceGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9 |
alaQoSServiceGroupEntryDefinition of QoS ServiceGroup QoSServiceGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9.1 |
alaQoSServiceGroupServiceNameName of service in service group entry DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9.1.1 |
alaQoSServiceGroupStatusUsed to create/delete service group entries according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9.1.2 |
alaQoSAppliedServiceGroupTableTable of QoS AppliedServiceGroup definitions SEQUENCE OF QoSAppliedServiceGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10 |
alaQoSAppliedServiceGroupEntryDefinition of QoS AppliedServiceGroup QoSAppliedServiceGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10.1 |
alaQoSAppliedServiceGroupServiceNameName of service in service group entry DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10.1.1 |
alaQoSAppliedServiceGroupStatusUsed to create/delete service group entries according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10.1.2 |
alaQoSNetworkGroupsTableTable of QoS NetworkGroups definitions SEQUENCE OF QoSNetworkGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11 |
alaQoSNetworkGroupsEntryDefinition of QoS NetworkGroups QoSNetworkGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1 |
alaQoSNetworkGroupsNameName of network group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1.1 |
alaQoSNetworkGroupsSourceWhat entity created the network group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1.2 |
alaQoSNetworkGroupsStatusUsed to create/delete network groups according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1.3 |
alaQoSAppliedNetworkGroupsTableTable of QoS AppliedNetworkGroups definitions SEQUENCE OF QoSAppliedNetworkGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12 |
alaQoSAppliedNetworkGroupsEntryDefinition of QoS AppliedNetworkGroups QoSAppliedNetworkGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1 |
alaQoSAppliedNetworkGroupsNameName of network group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1.1 |
alaQoSAppliedNetworkGroupsSourceWhat entity created the network group.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1.2 |
alaQoSAppliedNetworkGroupsStatusUsed to create/delete network groups according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1.3 |
alaQoSNetworkGroupTableTable of QoS NetworkGroup definitions SEQUENCE OF QoSNetworkGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13 |
alaQoSNetworkGroupEntryDefinition of QoS NetworkGroup QoSNetworkGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1 |
alaQoSNetworkGroupIpAddrIP address for network group entry. IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1.1 |
alaQoSNetworkGroupIpMaskIP mask for network group entry. IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1.2 |
alaQoSNetworkGroupStatusUsed to create/delete network group entries according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1.3 |
alaQoSAppliedNetworkGroupTableTable of QoS AppliedNetworkGroup definitions SEQUENCE OF QoSAppliedNetworkGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14 |
alaQoSAppliedNetworkGroupEntryDefinition of QoS AppliedNetworkGroup QoSAppliedNetworkGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1 |
alaQoSAppliedNetworkGroupIpAddrIP address for network group entry. IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1.1 |
alaQoSAppliedNetworkGroupIpMaskIP mask for network group entry. IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1.2 |
alaQoSAppliedNetworkGroupStatusUsed to create/delete network group entries according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1.3 |
alaQoSMACGroupsTableTable of QoS MACGroups definitions SEQUENCE OF QoSMACGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15 |
alaQoSMACGroupsEntryDefinition of QoS MACGroups QoSMACGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1 |
alaQoSMACGroupsNameName of MAC group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1.1 |
alaQoSMACGroupsSourceWhat entity created the MAC group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1.2 |
alaQoSMACGroupsStatusUsed to create/delete MAC groups according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1.3 |
alaQoSAppliedMACGroupsTableTable of QoS AppliedMACGroups definitions SEQUENCE OF QoSAppliedMACGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16 |
alaQoSAppliedMACGroupsEntryDefinition of QoS AppliedMACGroups QoSAppliedMACGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1 |
alaQoSAppliedMACGroupsNameName of MAC group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1.1 |
alaQoSAppliedMACGroupsSourceWhat entity created the MAC group.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1.2 |
alaQoSAppliedMACGroupsStatusUsed to create/delete MAC groups according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1.3 |
alaQoSMACGroupTableTable of QoS MACGroup definitions SEQUENCE OF QoSMACGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17 |
alaQoSMACGroupEntryDefinition of QoS MACGroup QoSMACGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1 |
alaQoSMACGroupMacAddrMAC address for MAC group entry MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1.1 |
alaQoSMACGroupMacMaskMAC mask for MAC group entry MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1.2 |
alaQoSMACGroupStatusUsed to create/delete MAC group entries according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1.3 |
alaQoSAppliedMACGroupTableTable of QoS AppliedMACGroup definitions SEQUENCE OF QoSAppliedMACGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18 |
alaQoSAppliedMACGroupEntryDefinition of QoS AppliedMACGroup QoSAppliedMACGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1 |
alaQoSAppliedMACGroupMacAddrMAC address for MAC group entry MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1.1 |
alaQoSAppliedMACGroupMacMaskMAC mask for MAC group entry MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1.2 |
alaQoSAppliedMACGroupStatusUsed to create/delete MAC group entries according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1.3 |
alaQoSPortGroupsTableTable of QoS PortGroups definitions SEQUENCE OF QoSPortGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19 |
alaQoSPortGroupsEntryDefinition of QoS PortGroups QoSPortGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1 |
alaQoSPortGroupsNameName of port group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1.1 |
alaQoSPortGroupsSourceWhat entity created the port group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1.2 |
alaQoSPortGroupsStatusUsed to create/delete port groups according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1.3 |
alaQoSAppliedPortGroupsTableTable of QoS AppliedPortGroups definitions SEQUENCE OF QoSAppliedPortGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20 |
alaQoSAppliedPortGroupsEntryDefinition of QoS AppliedPortGroups QoSAppliedPortGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1 |
alaQoSAppliedPortGroupsNameName of port group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1.1 |
alaQoSAppliedPortGroupsSourceWhat entity created the port group.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1.2 |
alaQoSAppliedPortGroupsStatusUsed to create/delete port groups according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1.3 |
alaQoSPortGroupTableTable of QoS PortGroup definitions SEQUENCE OF QoSPortGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21 |
alaQoSPortGroupEntryDefinition of QoS PortGroup QoSPortGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1 |
alaQoSPortGroupSlotPhysical slot for port group entry Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.1 |
alaQoSPortGroupPortPhysical port range start for port group entry Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.2 |
alaQoSPortGroupStatusUsed to create/delete port group entries according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.3 |
alaQoSPortGroupPortEndPhysical port range end for port group entry
Must be greater than port range start to indicate a range.
When '1', use port as a single port. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.4 |
alaQoSAppliedPortGroupTableTable of QoS AppliedPortGroup definitions SEQUENCE OF QoSAppliedPortGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22 |
alaQoSAppliedPortGroupEntryDefinition of QoS AppliedPortGroup QoSAppliedPortGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1 |
alaQoSAppliedPortGroupSlotPhysical slot for port group entry Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.1 |
alaQoSAppliedPortGroupPortPhysical port range start for port group entry Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.2 |
alaQoSAppliedPortGroupStatusUsed to create/delete port group entries according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.3 |
alaQoSAppliedPortGroupPortEndPhysical port range end for port group entry
Must be greater than port range start to indicate a range.
When '1', use port as a single port. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.4 |
alaQoSMapGroupsTableTable of QoS MapGroups definitions SEQUENCE OF QoSMapGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23 |
alaQoSMapGroupsEntryDefinition of QoS MapGroups QoSMapGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1 |
alaQoSMapGroupsNameName of map group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1.1 |
alaQoSMapGroupsSourceWhat entity created the map group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1.2 |
alaQoSMapGroupsStatusUsed to create/delete map groups according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1.3 |
alaQoSAppliedMapGroupsTableTable of QoS AppliedMapGroups definitions SEQUENCE OF QoSAppliedMapGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24 |
alaQoSAppliedMapGroupsEntryDefinition of QoS AppliedMapGroups QoSAppliedMapGroupsEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1 |
alaQoSAppliedMapGroupsNameName of map group DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1.1 |
alaQoSAppliedMapGroupsSourceWhat entity created the map group.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1.2 |
alaQoSAppliedMapGroupsStatusUsed to create/delete map groups according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1.3 |
alaQoSMapGroupTableTable of QoS MapGroup definitions SEQUENCE OF QoSMapGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25 |
alaQoSMapGroupEntryDefinition of QoS MapGroup QoSMapGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1 |
alaQoSMapGroupKeyKey range start of map group entry. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.1 |
alaQoSMapGroupKeyEndKey range end for map group entries. Key range end
must be greater than key range start to indicate a range.
When '0', use key range start as a single key. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.2 |
alaQoSMapGroupValueValue for map group entries. Value to stamp on traffic when
keys in the proper range are seen. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.3 |
alaQoSMapGroupStatusUsed to create/delete map group entries according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.4 |
alaQoSAppliedMapGroupTableTable of QoS AppliedMapGroup definitions SEQUENCE OF QoSAppliedMapGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26 |
alaQoSAppliedMapGroupEntryDefinition of QoS AppliedMapGroup QoSAppliedMapGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1 |
alaQoSAppliedMapGroupKeyKey range start of map group entry. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.1 |
alaQoSAppliedMapGroupKeyEndKey range end for map group entries. Key range end
must be greater than key range start to indicate a range.
When '0', use key range start as a single key. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.2 |
alaQoSAppliedMapGroupValueValue for map group entries. Value to stamp on traffic when
keys in the proper range are seen. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.3 |
alaQoSAppliedMapGroupStatusUsed to create/delete map group entries according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.4 |
alaQoSActionTableTable of QoS Action definitions SEQUENCE OF QoSActionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27 |
alaQoSActionEntryDefinition of QoS Action QoSActionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1 |
alaQoSActionNameName of action DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.1 |
alaQoSActionSourceWhat entity created the action.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.2 |
alaQoSActionDispositionDisposition of traffic using the action.
Use to filter out unwanted traffic.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.3 |
alaQoSActionDropAlgorithmWhich drop algorithm should be used to discard traffic when
oversubscribed.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.4 |
alaQoSActionWredMaximumThresholdBandwidth at which WRED should discard most traffic.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.5 |
alaQoSActionWredMaximumThresholdStatusStatus field indicating whether WRED maximum threshold
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.6 |
alaQoSActionWredMinimumThresholdBandwidth at which WRED should start to discard traffic.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.7 |
alaQoSActionWredMinimumThresholdStatusStatus field indicating whether WRED minimum threshold
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.8 |
alaQoSActionWredMaximumProbabilityProbabilty that traffic will be dropped at WRED
maximum threshold.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.9 |
alaQoSActionWredMaximumProbabilityStatusStatus field indicating whether WRED maximum probability
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.10 |
alaQoSActionMinimumBandwidthMinimum bandwidth (Kbits/sec) to guarantee for trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.11 |
alaQoSActionMinimumBandwidthStatusStatus field indicating whether minimum bandwidth
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.12 |
alaQoSActionMaximumBandwidthMaximum bandwidth (Kbits/sec) allowed for trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.13 |
alaQoSActionMaximumBandwidthStatusStatus field indicating whether maximum bandwidth
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.14 |
alaQoSActionPeakBandwidthPeak bandwidth (Kbits/sec) allowed for trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.15 |
alaQoSActionPeakBandwidthStatusStatus field indicating whether peak bandwidth
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.16 |
alaQoSActionPriorityInternal and queueing priority to use for traffic.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.17 |
alaQoSActionPriorityStatusStatus field indicating whether priority
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.18 |
alaQoSActionSharedWhen enabled, try and share any resources
(queues/limiters/descriptors) when more than one policy uses
the same action.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.19 |
alaQoSActionJitterMaximum jitter to allow for traffic.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.20 |
alaQoSActionJitterStatusStatus field indicating whether jitter
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.21 |
alaQoSActionLatencyMaximum latency to allow for traffic.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.22 |
alaQoSActionLatencyStatusStatus field indicating whether latency
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.23 |
alaQoSActionMaximumDepthMaximum depth (Kbytes) of queues for traffic.
Used for EBS in tri-color marker applications.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.24 |
alaQoSActionMaximumDepthStatusStatus field indicating whether maximum depth
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.25 |
alaQoSActionMaximumBuffersMaxmimum buffers for queues for traffic.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.26 |
alaQoSActionMaximumBuffersStatusStatus field indicating whether maximum buffers
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.27 |
alaQoSAction8021p802.1p value to stamp on traffic.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.28 |
alaQoSAction8021pStatusStatus field indicating whether 802.1p
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.29 |
alaQoSActionTosTOS value to stamp on traffic. (High 3 bits of TOS byte)rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.30 |
alaQoSActionTosStatusStatus field indicating whether TOS
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.31 |
alaQoSActionDscpTOS value to stamp on traffic. (High 6 bits of TOS byte)rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.32 |
alaQoSActionDscpStatusStatus field indicating whether DSCP
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.33 |
alaQoSActionMapFromWhat field to use as key for mapping 802.1p/TOS/DSCP prioritiesrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.34 |
alaQoSActionMapToWhat field to rewrite due to remapping 802.1p/TOS/DSCP
prioritiesrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.35 |
alaQoSActionMapGroupName of the map group to use when remapping 802.1p/TOS/DSCP
priorities.rw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.36 |
alaQoSActionMapGroupStatusStatus field indicating whether a map group
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.37 |
alaQoSActionSourceRewriteIpAddrSource IP address to rewrite on traffic.rw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.38 |
alaQoSActionSourceRewriteIpAddrStatusStatus field indicating whether source rewrite IP address & mask
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.39 |
alaQoSActionSourceRewriteIpMaskSource rewrite IP mask to determine how much of
source IP to rewrite.rw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.40 |
alaQoSActionSourceRewriteNetworkGroupName of network group containing source address/masks to rewrite
on traffic. Must be a one to on correspondence with
source network group entries in the condition.rw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.41 |
alaQoSActionSourceRewriteNetworkGroupStatusStatus field indicating whether source rewrite network group
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.42 |
alaQoSActionDestinationRewriteIpAddrDestination IP address to rewrite on traffic.rw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.43 |
alaQoSActionDestinationRewriteIpAddrStatusStatus field indicating whether destination rewrite IP address
& mask is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.44 |
alaQoSActionDestinationRewriteIpMaskDestination rewrite IP mask to determine how much of
destination IP to rewrite.rw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.45 |
alaQoSActionDestinationRewriteNetworkGroupName of network group containing destination address/masks to
rewrite on traffic. Must be a one to on correspondence with
destination network group entries in the condition.rw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.46 |
alaQoSActionDestinationRewriteNetworkGroupStatusStatus field indicating whether destination rewrite network
group is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.47 |
alaQoSActionLoadBalanceGroupName of load balance group to use for trafficrw DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.48 |
alaQoSActionLoadBalanceGroupStatusStatus field indicating whether load balanace group
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.49 |
alaQoSActionPermanentGatewayIpAddrNext hop gateway to use for trafficrw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.50 |
alaQoSActionPermanentGatewayIpAddrStatusStatus field indicating whether permanent gateway IP address
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.51 |
alaQoSActionAlternateGatewayIpAddrNext hop gateway to use for traffic that doesn't have an
explicit route. Use this gateway instead of default routes.rw IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.52 |
alaQoSActionAlternateGatewayIpAddrStatusStatus field indicating whether alternate gateway IP address
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.53 |
alaQoSActionRowStatusUsed to create/delete actions according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.54 |
alaQoSActionMinimumDepthMinimum depth (Kbytes) of queues for traffic.
Used for CBS in tri-color marker applications.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.55 |
alaQoSActionMinimumDepthStatusStatus field indicating whether minimum depth
is specified(enabled) or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.56 |
alaQoSActionVPNAccessHow to encrypt trafficrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.57 |
alaQoSActionNocacheWhen enabled, don't make hardware entries for matching flows.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.58 |
alaQoSActionPortdisableWhen enabled, disable the physical source port of the traffic.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.59 |
alaQoSActionRedirectSlotDestination physical slot for redirected trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.60 |
alaQoSActionRedirectSlotStatusStatus for alaQoSActionRedirectSlotStatus fieldrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.61 |
alaQoSActionRedirectPortDestination physical port for redirected trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.62 |
alaQoSActionRedirectAggDestination linkagg for redirected trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.63 |
alaQoSActionRedirectAggStatusStatus for alaQoSActionRedirectAggStatus fieldrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.64 |
alaQoSActionMirrorSlotDestination physical slot for mirrored trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.65 |
alaQoSActionMirrorPortDestination physical port for mirrored trafficrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.66 |
alaQoSActionMirrorModeMirroring moderw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.67 |
alaQoSActionMirrorModeStatusStatus for alaQoSActionMirrorMode fieldrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.68 |
alaQoSActionCIRCommitted Information Rate - bandwidth values in kilobits per second.rw Integer32 UNITS "kilobits per second" .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.69 |
alaQoSActionCIRStatusStatus field indicating whether CIR value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.70 |
alaQoSActionCBSCommitted Burst Size - bucket size in byte.rw Integer32(0 .. 2147450880) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.71 |
alaQoSActionCBSStatusStatus field indicating whether CBS value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.72 |
alaQoSActionPIRPeak Information Rate - bandwidth values in kilobits per second.rw Integer32 UNITS "kilobits per second" .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.73 |
alaQoSActionPIRStatusStatus field indicating whether PIR value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.74 |
alaQoSActionPBSPeak Burst Size - bucket size in byte.rw Integer32(0 .. 2147450880) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.75 |
alaQoSActionPBSStatusStatus field indicating whether PBS value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.76 |
alaQoSActionCounterColorSpecifies the color mode for the counters which will be used for sr/trTCM.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.77 |
alaQoSAppliedActionTableTable of QoS AppliedAction definitions SEQUENCE OF QoSAppliedActionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28 |
alaQoSAppliedActionEntryDefinition of QoS AppliedAction QoSAppliedActionEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1 |
alaQoSAppliedActionNameName of action DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.1 |
alaQoSAppliedActionSourceWhat entity created the action.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.2 |
alaQoSAppliedActionDispositionDisposition of traffic using the action.
Use to filter out unwanted traffic.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.3 |
alaQoSAppliedActionDropAlgorithmWhich drop algorithm should be used to discard traffic when
oversubscribed.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.4 |
alaQoSAppliedActionWredMaximumThresholdBandwidth at which WRED should discard most traffic.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.5 |
alaQoSAppliedActionWredMaximumThresholdStatusStatus field indicating whether WRED maximum threshold
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.6 |
alaQoSAppliedActionWredMinimumThresholdBandwidth at which WRED should start to discard traffic.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.7 |
alaQoSAppliedActionWredMinimumThresholdStatusStatus field indicating whether WRED minimum threshold
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.8 |
alaQoSAppliedActionWredMaximumProbabilityProbabilty that traffic will be dropped at WRED
maximum threshold.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.9 |
alaQoSAppliedActionWredMaximumProbabilityStatusStatus field indicating whether WRED maximum probability
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.10 |
alaQoSAppliedActionMinimumBandwidthMinimum bandwidth (Kbits/sec) to guarantee for trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.11 |
alaQoSAppliedActionMinimumBandwidthStatusStatus field indicating whether minimum bandwidth
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.12 |
alaQoSAppliedActionMaximumBandwidthMaximum bandwidth (Kbits/sec) allowed for trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.13 |
alaQoSAppliedActionMaximumBandwidthStatusStatus field indicating whether maximum bandwidth
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.14 |
alaQoSAppliedActionPeakBandwidthPeak bandwidth (Kbits/sec) allowed for trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.15 |
alaQoSAppliedActionPeakBandwidthStatusStatus field indicating whether peak bandwidth
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.16 |
alaQoSAppliedActionPriorityInternal and queueing priority to use for traffic.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.17 |
alaQoSAppliedActionPriorityStatusStatus field indicating whether priority
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.18 |
alaQoSAppliedActionSharedWhen enabled, try and share any resources
(queues/limiters/descriptors) when more than one policy uses
the same action.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.19 |
alaQoSAppliedActionJitterMaximum jitter to allow for traffic.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.20 |
alaQoSAppliedActionJitterStatusStatus field indicating whether jitter
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.21 |
alaQoSAppliedActionLatencyMaximum latency to allow for traffic.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.22 |
alaQoSAppliedActionLatencyStatusStatus field indicating whether latency
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.23 |
alaQoSAppliedActionMaximumDepthMaximum depth (Kbytes) of queues for traffic.
Used for EBS in tri-color marker applications.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.24 |
alaQoSAppliedActionMaximumDepthStatusStatus field indicating whether maximum depth
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.25 |
alaQoSAppliedActionMaximumBuffersMaxmimum buffers for queues for traffic.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.26 |
alaQoSAppliedActionMaximumBuffersStatusStatus field indicating whether maximum buffers
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.27 |
alaQoSAppliedAction8021p802.1p value to stamp on traffic.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.28 |
alaQoSAppliedAction8021pStatusStatus field indicating whether 802.1p
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.29 |
alaQoSAppliedActionTosTOS value to stamp on traffic. (High 3 bits of TOS byte)ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.30 |
alaQoSAppliedActionTosStatusStatus field indicating whether TOS
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.31 |
alaQoSAppliedActionDscpTOS value to stamp on traffic. (High 6 bits of TOS byte)ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.32 |
alaQoSAppliedActionDscpStatusStatus field indicating whether DSCP
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.33 |
alaQoSAppliedActionMapFromWhat field to use as key for mapping 802.1p/TOS/DSCP prioritiesro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.34 |
alaQoSAppliedActionMapToWhat field to rewrite due to remapping 802.1p/TOS/DSCP
prioritiesro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.35 |
alaQoSAppliedActionMapGroupName of the map group to use when remapping 802.1p/TOS/DSCP
priorities.ro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.36 |
alaQoSAppliedActionMapGroupStatusStatus field indicating whether a map group
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.37 |
alaQoSAppliedActionSourceRewriteIpAddrSource IP address to rewrite on traffic.ro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.38 |
alaQoSAppliedActionSourceRewriteIpAddrStatusStatus field indicating whether source rewrite IP address & mask
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.39 |
alaQoSAppliedActionSourceRewriteIpMaskSource rewrite IP mask to determine how much of
source IP to rewrite.ro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.40 |
alaQoSAppliedActionSourceRewriteNetworkGroupName of network group containing source address/masks to rewrite
on traffic. Must be a one to on correspondence with
source network group entries in the condition.ro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.41 |
alaQoSAppliedActionSourceRewriteNetworkGroupStatusStatus field indicating whether source rewrite network group
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.42 |
alaQoSAppliedActionDestinationRewriteIpAddrDestination IP address to rewrite on traffic.ro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.43 |
alaQoSAppliedActionDestinationRewriteIpAddrStatusStatus field indicating whether destination rewrite IP address
& mask is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.44 |
alaQoSAppliedActionDestinationRewriteIpMaskDestination rewrite IP mask to determine how much of
destination IP to rewrite.ro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.45 |
alaQoSAppliedActionDestinationRewriteNetworkGroupName of network group containing destination address/masks to
rewrite on traffic. Must be a one to on correspondence with
destination network group entries in the condition.ro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.46 |
alaQoSAppliedActionDestinationRewriteNetworkGroupStatusStatus field indicating whether destination rewrite network
group is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.47 |
alaQoSAppliedActionLoadBalanceGroupName of load balance group to use for trafficro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.48 |
alaQoSAppliedActionLoadBalanceGroupStatusStatus field indicating whether load balanace group
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.49 |
alaQoSAppliedActionPermanentGatewayIpAddrNext hop gateway to use for trafficro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.50 |
alaQoSAppliedActionPermanentGatewayIpAddrStatusStatus field indicating whether permanent gateway IP address
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.51 |
alaQoSAppliedActionAlternateGatewayIpAddrNext hop gateway to use for traffic that doesn't have an
explicit route. Use this gateway instead of default routes.ro IpAddress .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.52 |
alaQoSAppliedActionAlternateGatewayIpAddrStatusStatus field indicating whether alternate gateway IP address
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.53 |
alaQoSAppliedActionRowStatusUsed to create/delete actions according to the
RowStatus conventionro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.54 |
alaQoSAppliedActionMinimumDepthMinimum depth (Kbytes) of queues for traffic.
Used for CBS in tri-color marker applications.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.55 |
alaQoSAppliedActionMinimumDepthStatusStatus field indicating whether minimum depth
is specified(enabled) or not(disabled).ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.56 |
alaQoSAppliedActionVPNAccessHow to encrypt trafficro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.57 |
alaQoSAppliedActionNocacheWhen enabled, don't make hardware entries for matching flows.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.58 |
alaQoSAppliedActionPortdisableWhen enabled, disable the physical source port of the traffic.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.59 |
alaQoSAppliedActionRedirectSlotDestination physical slot for redirected trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.60 |
alaQoSAppliedActionRedirectSlotStatusStatus for alaQoSAppliedActionRedirectSlotStatus fieldro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.61 |
alaQoSAppliedActionRedirectPortDestination physical port for redirected trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.62 |
alaQoSAppliedActionRedirectAggDestination linkagg for redirected trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.63 |
alaQoSAppliedActionRedirectAggStatusStatus for alaQoSAppliedActionRedirectAggStatus fieldro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.64 |
alaQoSAppliedActionMirrorSlotDestination physical slot for mirrored trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.65 |
alaQoSAppliedActionMirrorPortDestination physical port for mirrored trafficro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.66 |
alaQoSAppliedActionMirrorModeMirroring modero Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.67 |
alaQoSAppliedActionMirrorModeStatusStatus for alaQoSAppliedActionMirrorMode fieldro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.68 |
alaQoSAppliedActionCIRCommitted Information Rate - bandwidth values in kilobits per second.rw Integer32 UNITS "kilobits per second" .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.69 |
alaQoSAppliedActionCIRStatusStatus field indicating whether CIR value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.70 |
alaQoSAppliedActionCBSCommitted Burst Size - bucket size in byte.rw Integer32(0 .. 2147450880) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.71 |
alaQoSAppliedActionCBSStatusStatus field indicating whether CBS value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.72 |
alaQoSAppliedActionPIRPeak Information Rate - bandwidth values in kilobits per second.rw Integer32 UNITS "kilobits per second" .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.73 |
alaQoSAppliedActionPIRStatusStatus field indicating whether PIR value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.74 |
alaQoSAppliedActionPBSPeak Burst Size - bucket size in byte.rw Integer32(0 .. 2147450880) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.75 |
alaQoSAppliedActionPBSStatusStatus field indicating whether PBS value is specified(enabled)
or not(disabled).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.76 |
alaQoSAppliedActionCounterColorSpecifies the color mode for the counters which will be used for sr/trTCM.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.77 |
alaQoSPortTableTable of QoS Port definitions SEQUENCE OF QoSPortEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29 |
alaQoSPortEntryDefinition of QoS Port QoSPortEntry .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1 |
alaQoSPortSlotPhysical slot port resides on Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.1 |
alaQoSPortPortPhysical port number Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.2 |
alaQoSPortEnabledPending QoS enable status for the physical port
Does not take effect until an 'Apply' command is issuedrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.3 |
alaQoSPortAppliedEnabledCurrent QoS enable status for the physical portro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.4 |
alaQoSPortInterfaceTypeThe type of interface QoS matches for this physical portro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.5 |
alaQoSPortTrustedStatus of trusting 802.1p/TOS/DSCP values.
When trusted, 802.1p/DSCP values in the packet are passed
through the switch. When untrusted, 802.1p/DSCP values are set
to the port defaults.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.6 |
alaQoSPortDefault8021p802.1p priority value to use for untagged frames arriving on
the port and tagged frames when the port is untrusted.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.7 |
alaQoSPortDefaultDSCPDSCP value to stamp in frames arriving on the port when the port
is untrustedrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.8 |
alaQoSPortMaximumReservedBandwidthPending maximum reservable bandwidth on the port.
Policies can reserve up to this much bandwidth.
Does not take effect until an 'Apply' is issuedrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.9 |
alaQoSPortMaximumReservedBandwidthStatusPending status field indicating whether to enforce
maximum reservable bandwidth on next 'Apply'rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.10 |
alaQoSPortAppliedMaximumReservedBandwidthCurrent maximum reservable bandwidth on the port.
Policies can reserve up to this much bandwidth.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.11 |
alaQoSPortAppliedMaximumReservedBandwidthStatusCurrent status field indicating whether to enforce
maximum reservable bandwidth.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.12 |
alaQoSPortMaximumSignalledBandwidthPending maximum signalled bandwidth on the port.
Signalling protocols can reserve up to this much bandwidth.
Does not take effect until an 'Apply' is issuedrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.13 |
alaQoSPortMaximumSignalledBandwidthStatusPending status field indicating whether to enforce
maximum signalled bandwidth on next 'Apply'rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.14 |
alaQoSPortAppliedMaximumSignalledBandwidthCurrent maximum signalled bandwidth on the port.
Signalling protocols can reserve up to this much bandwidth.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.15 |
alaQoSPortAppliedMaximumSignalledBandwidthStatusCurrent status field indicating whether to enforce
maximum signalled bandwidth.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.16 |
alaQoSPortDefaultQueuesPending number of default queues for the port
Overrides any switch-wide default queue settingrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.17 |
alaQoSPortAppliedDefaultQueuesCurrent number of default queues for the port
Overrides any switch-wide default queue settingro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.18 |
alaQoSPortMaximumDefaultBandwidthPending maximum default bandwidth (Kbits/sec).
Maximum rate for default queues on this port
Does not take effect until an 'Apply' command is issuedrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.19 |
alaQoSPortMaximumDefaultBandwidthStatusPending status field indicating whether to enforce
maximum default bandwidth on next 'Apply'rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.20 |
alaQoSPortAppliedMaximumDefaultBandwidthCurrent maximum default bandwidth (Kbits/sec).
Maximum rate for default queues this portro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.21 |
alaQoSPortAppliedMaximumDefaultBandwidthStatusCurrent status field indicating whether to enforce
maximum default bandwidth.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.22 |
alaQoSPortMaximumDefaultDepthPending maximum depth of egress queues (Kbytes).
Maximum depth of queues on this port
Does not take effect until an 'Apply' command is issuedrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.23 |
alaQoSPortMaximumDefaultDepthStatusPending status field indicating whether to enforce
maximum depth on next 'Apply'rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.24 |
alaQoSPortAppliedMaximumDefaultDepthCurrent maximum depth of egress queues (Kbytes).
Maximum depth of queues on this portro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.25 |
alaQoSPortAppliedMaximumDefaultDepthStatusCurrent status field indicating whether to enforce
maximum depth.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.26 |
alaQoSPortMaximumDefaultBuffersPending maximum buffers for egress queues.
Maximum number of buffers for queues on this port
Does not take effect until an 'Apply' command is issuedrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.27 |
alaQoSPortMaximumDefaultBuffersStatusPending status field indicating whether to enforce
maximum buffers on next 'Apply'rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.28 |
alaQoSPortAppliedMaximumDefaultBuffersCurrent maximum buffers for egress queues.
Maximum number of buffers for queues on this portro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.29 |
alaQoSPortAppliedMaximumDefaultBuffersStatusCurrent status field indicating whether to enforce
maximum buffers.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.30 |
alaQoSPortResetReset all QoS parameters to default valuesrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.31 |
alaQoSPortPhysicalBandwidthPhysical bandwidth of port (Kbit/sec)ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.32 |
alaQoSPortReservedBandwidthBandwidth reserved by policies on port (Kbit/sec)ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.33 |
alaQoSPortSignalledBandwidthBandwidth reserved by signalling on port (Kbit/sec)ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.34 |
alaQoSPortCurrentBandwidthCurrent measured bandwidth of port (Kbits/sec)ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.35 |
alaQoSPortDefaultQidLowDefault low queue IDro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.36 |
alaQoSPortDefaultQidMediumDefault medium queue IDro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.37 |
alaQoSPortDefaultQidHighDefault high queue IDro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.38 |
alaQoSPortDefaultQidUrgentDefault urgent queue IDro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.39 |
alaQoSPortFloodQidID of the flood queuero Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.40 |
alaQoSPortQueuesNumber of queues currently on the portro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.41 |
alaQoSPortQueuesCreatedNumber of queue requests on the portro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.42 |
alaQoSPortQueuesFailedNumber of queue requests that failed on the portro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.43 |
alaQoSPortQueuesPreemptedNumber of queues preempted on the portro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.44 |
alaQoSPortRowStatusUsed to create/delete ports according to the
RowStatus conventionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.45 |
alaQoSPortFirPrio0EnqBytesFirenze priority 0 enqueue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.46 |
alaQoSPortFirPrio0DeqBytesFirenze priority 0 dequeue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.47 |
alaQoSPortFirPrio0EnqPktsFirenze priority 0 enqueue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.48 |
alaQoSPortFirPrio0DeqPktsFirenze priority 0 dequeue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.49 |
alaQoSPortFirPrio0QidDiscardPktsFirenze priority 0 QID discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.50 |
alaQoSPortFirPrio0WredDiscardPktsFirenze priority 0 WRED discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.51 |
alaQoSPortFirPrio0OverflowDiscardPktsFirenze priority 0 overflow discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.52 |
alaQoSPortFirPrio1EnqBytesFirenze priority 1 enqueue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.53 |
alaQoSPortFirPrio1DeqBytesFirenze priority 1 dequeue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.54 |
alaQoSPortFirPrio1EnqPktsFirenze priority 1 enqueue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.55 |
alaQoSPortFirPrio1DeqPktsFirenze priority 1 dequeue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.56 |
alaQoSPortFirPrio1QidDiscardPktsFirenze priority 1 QID discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.57 |
alaQoSPortFirPrio1WredDiscardPktsFirenze priority 1 WRED discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.58 |
alaQoSPortFirPrio1OverflowDiscardPktsFirenze priority 1 overflow discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.59 |
alaQoSPortFirPrio2EnqBytesFirenze priority 2 enqueue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.60 |
alaQoSPortFirPrio2DeqBytesFirenze priority 2 dequeue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.61 |
alaQoSPortFirPrio2EnqPktsFirenze priority 2 enqueue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.62 |
alaQoSPortFirPrio2DeqPktsFirenze priority 2 dequeue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.63 |
alaQoSPortFirPrio2QidDiscardPktsFirenze priority 2 QID discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.64 |
alaQoSPortFirPrio2WredDiscardPktsFirenze priority 2 WRED discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.65 |
alaQoSPortFirPrio2OverflowDiscardPktsFirenze priority 2 overflow discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.66 |
alaQoSPortFirPrio3EnqBytesFirenze priority 3 enqueue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.67 |
alaQoSPortFirPrio3DeqBytesFirenze priority 3 dequeue byte countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.68 |
alaQoSPortFirPrio3EnqPktsFirenze priority 3 enqueue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.69 |
alaQoSPortFirPrio3DeqPktsFirenze priority 3 dequeue packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.70 |
alaQoSPortFirPrio3QidDiscardPktsFirenze priority 3 QID discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.71 |
alaQoSPortFirPrio3WredDiscardPktsFirenze priority 3 WRED discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.72 |
alaQoSPortFirPrio3OverflowDiscardPktsFirenze priority 3 overflow discard packet countro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.73 |
alaQoSPortDefaultClassificationIngress traffic classification parameter for Firenze port
What field to interpret as priority for WREDrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.74 |
alaQoSPortLowPriorityWeightWeight to use for low priority egress queue on fixed queue blades.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.75 |
alaQoSPortMediumPriorityWeightWeight to use for medium priority egress queue on fixed queue blades.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.76 |
alaQoSPortHighPriorityWeightWeight to use for high priority egress queue on fixed queue blades.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.77 |
alaQoSPortUrgentPriorityWeightWeight to use for urgent priority egress queue on fixed queue blades.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.78 |
alaQoSPortMaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this portrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.79 |
alaQoSPortMaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on port.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.80 |
alaQoSPortEnqueuingThresholdP0LowerPriority 0 FIFO lower threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.81 |
alaQoSPortEnqueuingThresholdP0UpperPriority 0 FIFO upper threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.82 |
alaQoSPortEnqueuingThresholdP1LowerPriority 1 FIFO lower threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.83 |
alaQoSPortEnqueuingThresholdP1UpperPriority 1 FIFO upper threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.84 |
alaQoSPortEnqueuingThresholdP2LowerPriority 2 FIFO lower threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.85 |
alaQoSPortEnqueuingThresholdP2UpperPriority 2 FIFO upper threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.86 |
alaQoSPortEnqueuingThresholdP3LowerPriority 3 FIFO lower threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.87 |
alaQoSPortEnqueuingThresholdP3UpperPriority 3 FIFO upper threshold for high density modulerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.88 |
alaQoSPortEnqueuingThresholdStatusStatus field indicating whether enqueuing thresholds need
to be enforced on high density module.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.89 |
alaQoSPortHighDensityIndicates whether this is a high-density port or not.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.90 |
alaQoSPortServicingModeServicing mode for the portrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.91 |
alaQoSPortFreeFFPRulesNumber of Free FPP rule entriesro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.92 |
alaQoSPortUsedFFPRulesNumber of Used FPP rule entriesro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.93 |
alaQoSPortFreeFFPMasksNumber of Free FPP mask entriesro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.94 |
alaQoSPortUsedFFPMasksNumber of Free FPP mask enriesro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.95 |
alaQoSPortSpoofedCountSpoofed packet countro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.96 |
alaQoSPortNonSpoofedCountNon-spoofed packet countro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.97 |
alaQoSPortQ4PriorityWeightWeight to use for cos queue 4.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.98 |
alaQoSPortQ5PriorityWeightWeight to use for cos queue 5.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.99 |
alaQoSPortQ6PriorityWeightWeight to use for cos queue 6.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.100 |
alaQoSPortQ7PriorityWeightWeight to use for cos queue 7.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.101 |
alaQoSPortCOS0MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.102 |
alaQoSPortCOS0MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.103 |
alaQoSPortCOS1MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.104 |
alaQoSPortCOS1MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.105 |
alaQoSPortCOS2MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.106 |
alaQoSPortCOS2MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.107 |
alaQoSPortCOS3MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.108 |
alaQoSPortCOS3MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.109 |
alaQoSPortCOS4MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.110 |
alaQoSPortCOS4MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.111 |
alaQoSPortCOS5MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.112 |
alaQoSPortCOS5MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.113 |
alaQoSPortCOS6MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.114 |
alaQoSPortCOS6MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.115 |
alaQoSPortCOS7MaximumBandwidthMaximum egress bandwidth (Kbits/sec).
Maximum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.116 |
alaQoSPortCOS7MaximumBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.117 |
alaQoSPortCOS0MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.118 |
alaQoSPortCOS0MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.119 |
alaQoSPortCOS1MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.120 |
alaQoSPortCOS1MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.121 |
alaQoSPortCOS2MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.122 |
alaQoSPortCOS2MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.123 |
alaQoSPortCOS3MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.124 |
alaQoSPortCOS3MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.125 |
alaQoSPortCOS4MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.126 |
alaQoSPortCOS4MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.127 |
alaQoSPortCOS5MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.128 |
alaQoSPortCOS5MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.129 |
alaQoSPortCOS6MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.130 |
alaQoSPortCOS6MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.131 |
alaQoSPortCOS7MinimumBandwidthMinimum egress bandwidth (Kbits/sec).
Minimum rate to send traffic out this queuerw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.132 |
alaQoSPortCOS7MinimumBandwidthStatusStatus field indicating whether to enforce
minimum bandwidth on queue.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.133 |
alaQoSPortMaximumIngBandwidthMaximum igress bandwidth (Kbits/sec).
Maximum rate to recieve traffic in on this portrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.134 |
alaQoSPortMaximumIngBandwidthStatusStatus field indicating whether to enforce
maximum bandwidth on port.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.135 |
alaQoSPortDEIMarkingThis object specifies if, in egress traffic, the DEI/CFI bit
will be set or not for the traffic which is not conformant to
SLA (Yellow color packets).
enabled(1)
disabled(2)
DEFVAL { disabled }
::= { alaQoSPortEntry 136 }
alaQoSPortMonitor OBJECT-TYPE
SYNTAX INTEGER {
enabled (1),
disabled (2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTIONrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.137 |
alaQoSPortDEIMappingThis object specifies if, in ingress traffic, the DEI/CFI bit
will be set or not for the traffic which is not conformant to
SLA (Yellow color packets).
enabled(1)
disabled(2)
DEFVAL { disabled }
::= { alaQoSPortEntry 138 }
alaQoSConfig OBJECT IDENTIFIER ::= { alaQoSMIBObjects 30 }
alaQoSConfigEnabled OBJECT-TYPE
SYNTAX INTEGER {
enable (1),
disable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTIONrw Enumeration .alaQoSMIBCompliances.1 |