AIXIRB-MIB
AI MIB Summary
The AIXIRB-MIB module facilitates the monitoring and management of TCP options and passive/extended link configurations on AIX-based systems utilizing the SLC (System Link Control) framework. It exposes specific metrics for TCP extension parameters and link state settings to enable granular troubleshooting of network interface behavior and protocol negotiation on IBM AIX servers.
SLC MIB for misc. TCP options and passive/extended link settings
Main OID:
aiXirb.1.3.6.1.4.1.539.16.5
19
Objects
Active
Status
1
Dependencies
Imported Objects
Objects
19 total| Object Name |
|---|
aii OBJECT IDENTIFIER .1.3.6.1.4.1.539 |
aiSystemOID OBJECT IDENTIFIER .1.3.6.1.4.1.539.2 |
aiSLC2 OBJECT IDENTIFIER .1.3.6.1.4.1.539.16 |
aiXirbSLC MIB for misc. TCP options and passive/extended link settings MODULE-IDENTITY .1.3.6.1.4.1.539.16.5 |
aiXirbSystem OBJECT IDENTIFIER .1.3.6.1.4.1.539.16.5.1 |
aiXirbTcp OBJECT IDENTIFIER .1.3.6.1.4.1.539.16.5.2 |
aiXirbTcpWindowSizeDefault window size for TCP connections. Current connections will maintain their current window sizes, but new connections will use the updated window size.rw Enumeration .1.3.6.1.4.1.539.16.5.2.1 |
aiXirbTcpSendAheadIndicates whether or not TCP connections wait for data acknowledgment before sending more data (if disabled (1)), or send the maximum TCP window size before requiring data to be acknowledged (if enabled (2)).rw Enumeration .1.3.6.1.4.1.539.16.5.2.2 |
aiXirbX25 OBJECT IDENTIFIER .1.3.6.1.4.1.539.16.5.3 |
aiXirbBx25CallDownIf set to off(2), a passive link will stay up after all calls are disconnected. If set to on(1), a passive link will drop and go into DMLOCK (see aiXirbBx25DMlock below) when all the incomming calls are terminated. This object is meaningful only when aiLinkX25LinkMode is set to passive(2) on a given linkrw Enumeration .1.3.6.1.4.1.539.16.5.3.1 |
aiXirbBx25DMlockThe number of seconds to wait for after a link has gone inactive before allowing an outgoing call to attemp to bring up the link. Any outgoing call attempts will be rejected until the DMLOCK timer expires and the passive link returns to the standby mode. This object is meaningful only when aiLinkX25LinkMode is set to passive(2) on a given linkrw INTEGER .1.3.6.1.4.1.539.16.5.3.2 |
aiXirbBx25LinkUpThe number of seconds to wait for a passive link to become active. This object is meaningful only when aiLinkX25LinkMode is set to passive(2) on a given linkrw INTEGER .1.3.6.1.4.1.539.16.5.3.3 |
aiXirbCpuStats OBJECT IDENTIFIER .1.3.6.1.4.1.539.16.5.4 |
aiXirbCpuStatsCurrentThis indicates the average of percentage CPU utilization during last 60 secondsro INTEGER .1.3.6.1.4.1.539.16.5.4.1 |
aiXirbCpuStatsMaxThis shows the maximum percentage CPU utilization during last 24 hours. This value is calculated from the average CPU utilization information which is found every 60 seconds.ro INTEGER .1.3.6.1.4.1.539.16.5.4.2 |
aiXirbCpuStatsResetThis resets the CPU utilization statisticsrw Enumeration .1.3.6.1.4.1.539.16.5.4.3 |
aiXirbEthernet OBJECT IDENTIFIER .1.3.6.1.4.1.539.16.5.5 |
aiXirbPpc10BaseTDetermines whether the front panel 10 BaseT interface is enabled or not on - to enable the 10 BaseT interface off - to disable the 10 BaseT interfacerw Enumeration .1.3.6.1.4.1.539.16.5.5.1 |
aiXirb10BaseTDuplexFor AIwan only. Setting this to full(1) puts the AIwan Ethernet interface into Full Duplex mode (sends and receives simultaneously). Setting this to half(2) puts the AIwan Ethernet interface into Half Duplex mode (sends OR receives, but not simultaneously -- this means that collisions are possible). In general, half duplex works fine for switches AND hubs, whereas full duplex mode should only be used with switches or other interfaces that are full duplex capable.rw Enumeration .1.3.6.1.4.1.539.16.5.5.2 |