AI-AP-MIB
AI MIB Summary
The AI-AP-MIB module enables SNMP-based monitoring and management of Aruba Instant Access Points, specifically tracking wireless interface states, client association counts, radio utilization, and access point health metrics within an Aruba Instant virtual controller environment.
This MIB is for managing Aruba Instant WLAN
Main OID:
aiMIB.1.3.6.1.4.1.14823.2.3.3.1
365
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
365 total| Object Name |
|---|
aiMIBThis MIB is for managing Aruba Instant WLAN MODULE-IDENTITY .1.3.6.1.4.1.14823.2.3.3.1 |
aiInfoGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14823.2.3.3.1.1 |
aiVirtualControllerKeyUnique Virtual Controller keyro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.1.1 |
aiVirtualControllerNameVirtual Controller namero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.1.2 |
aiVirtualControllerOrganizationVirtual Controller organizationro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.1.3 |
aiVirtualControllerVersionSoftware Versionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.1.4 |
aiVirtualControllerIPAddressVirtual Controller IP Address. If this is not set, returns 0.0.0.0ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.1.5 |
aiMasterIPAddressIP Address of AP where virtual controller software is activero IpAddress .1.3.6.1.4.1.14823.2.3.3.1.1.6 |
aiWlanSSIDTable SEQUENCE OF AiWlanSSIDEntry .1.3.6.1.4.1.14823.2.3.3.1.1.7 |
aiWlanSSIDEntry AiWlanSSIDEntry .1.3.6.1.4.1.14823.2.3.3.1.1.7.1 |
aiSSIDIndexSSID Indexro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.1.7.1.1 |
aiSSIDSSIDro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.1.7.1.2 |
aiSSIDStatusIndicates the whether the SSID is enabled(0) or disabled(1)ro Enumeration .1.3.6.1.4.1.14823.2.3.3.1.1.7.1.3 |
aiStateGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14823.2.3.3.1.2 |
aiAccessPointTableThis contains all access points connected to the virtual controller. This table is empty on AP where virtual controller is not active SEQUENCE OF AiAccessPointEntry .1.3.6.1.4.1.14823.2.3.3.1.2.1 |
aiAccessPointEntry AiAccessPointEntry .1.3.6.1.4.1.14823.2.3.3.1.2.1.1 |
aiAPMACAddressAccess Point MAC Addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.1 |
aiAPNameAccess Point namero DisplayString .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.2 |
aiAPIPAddressAccess Point IP Addressro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.3 |
aiAPSerialNumAccess Point Serial Numberro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.4 |
aiAPModelAccess Point System OIDro OBJECT IDENTIFIER .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.5 |
aiAPModelNameAccess Point Model Namero DisplayString .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.6 |
aiAPCPUUtilizationAccess Point CPU Utilizationro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.7 |
aiAPMemoryFreeAmount of memory free in the access point in bytesro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.8 |
aiAPUptimeAccess Point uptimero TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.9 |
aiAPTotalMemoryTotal amount of memory available in the AP in bytesro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.10 |
aiAPStatusIndicates the Access Point Statusro Enumeration .1.3.6.1.4.1.14823.2.3.3.1.2.1.1.11 |
aiRadioTableThis table contains all radios of all access points connected to the virtual controller. This table is indexed by Access Point MAC Address and radio number SEQUENCE OF AiRadioEntry .1.3.6.1.4.1.14823.2.3.3.1.2.2 |
aiRadioEntry AiRadioEntry .1.3.6.1.4.1.14823.2.3.3.1.2.2.1 |
aiRadioAPMACAddressMAC Address of access point where this radio is activero MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.1 |
aiRadioIndexRadio numberro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.2 |
aiRadioMACAddressRadio MAC Addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.3 |
aiRadioChannelRadio channel. First byte contains primary channel and first two bits on second byte contains indicator for secondary channel. If first two bits of second byte is 0, it is a 20MHz channel. If first two bits of second byte is 01, secondary channel is above primary channel, if first two bits of second by is 10, secondary channel is below the primary channel.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.4 |
aiRadioTransmitPowerRadio transmit powerro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.5 |
aiRadioNoiseFloorRadio noise floor in dBmro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.6 |
aiRadioUtilization4Radio channel utilization 4 second averagero Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.7 |
aiRadioUtilization64Radio channel utilization 64 second averagero Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.8 |
aiRadioTxTotalFramesTotal transmitted framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.9 |
aiRadioTxMgmtFramesTransmitted management framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.10 |
aiRadioTxDataFramesTransmitted data framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.11 |
aiRadioTxDataBytesTransmitted data bytesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.12 |
aiRadioTxDropsTotal frames dropped during transmissionro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.13 |
aiRadioRxTotalFramesTotal received framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.14 |
aiRadioRxDataFramesReceived data framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.15 |
aiRadioRxDataBytesReceived data bytesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.16 |
aiRadioRxMgmtFramesReceived management framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.17 |
aiRadioRxBadFrames received in errorro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.18 |
aiRadioPhyEventsNumber of phy events that indicates frames not received because of interferencero Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.19 |
aiRadioStatusRadio state of AP - UP/DOWNro Enumeration .1.3.6.1.4.1.14823.2.3.3.1.2.2.1.20 |
aiWlanTableThis table contains all BSSIDs active on this virtual controller. This table is indexed by Access Point MAC Address and a WLAN Index SEQUENCE OF AiWlanEntry .1.3.6.1.4.1.14823.2.3.3.1.2.3 |
aiWlanEntry AiWlanEntry .1.3.6.1.4.1.14823.2.3.3.1.2.3.1 |
aiWlanAPMACAddressMAC Address of access point where WLAN is activero MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.1 |
aiWlanIndexIndex of WLAN. This is a unique index assigned to the WLAN active on the access point.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.2 |
aiWlanESSIDESSID of WLANro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.3 |
aiWlanMACAddressBSSID of WLANro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.4 |
aiWlanTxTotalFramesTotal transmitted framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.5 |
aiWlanTxDataFramesTransmitted data framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.6 |
aiWlanTxDataBytesTransmitted data bytesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.7 |
aiWlanRxTotalFramesTotal received framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.8 |
aiWlanRxDataFramesReceived data framesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.9 |
aiWlanRxDataBytesReceived data bytesro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.3.1.10 |
aiClientTableThis table contains information about all clients connected to the virtual controller. When a client roams from one access point to another, all counters in this table are reset to 0. aiClientUptime also get reset on a mobility event SEQUENCE OF AiClientEntry .1.3.6.1.4.1.14823.2.3.3.1.2.4 |
aiClientEntry AiClientEntry .1.3.6.1.4.1.14823.2.3.3.1.2.4.1 |
aiClientMACAddressMAC Address of clientro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.1 |
aiClientWlanMACAddressBSSID of WLAN where client is associatedro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.2 |
aiClientIPAddressClient IP Addressro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.3 |
aiClientAPIPAddressAssociated Access Point IP Addressro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.4 |
aiClientNameName of user using the clientro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.5 |
aiClientOperatingSystemClient operating systemro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.6 |
aiClientSNRSignal to noise ratio of client connection to the access pointro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.7 |
aiClientTxDataFramesTotal frames transmitted by the clientro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.8 |
aiClientTxDataBytesTotal bytes transmitted by the clientro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.9 |
aiClientTxRetriesTotal number of retry frames transmitted by the clientro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.10 |
aiClientTxRateTransmit rate of client in mbpsro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.11 |
aiClientRxDataFramesTotal frames received by the clientro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.12 |
aiClientRxDataBytesTotal bytes received by the clientro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.13 |
aiClientRxRetriesTotal number of retry frames received by the clientro Counter32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.14 |
aiClientRxRateReceive rate of client in mbpsro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.15 |
aiClientUptimeClient uptime. On mobility event all counters are reset to 0 and uptime gets reset to 0.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.14823.2.3.3.1.2.4.1.16 |
aiVoiceClientTableTable of voice clients SEQUENCE OF AiVoiceClientEntry .1.3.6.1.4.1.14823.2.3.3.1.2.5 |
aiVoiceClientEntryEntry of a voice client AiVoiceClientEntry .1.3.6.1.4.1.14823.2.3.3.1.2.5.1 |
aiClientMacMAC address of voice clientro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.5.1.1 |
aiClientIPIP address of voice clientro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.2.5.1.2 |
aiClientAPMacMAC address of AP on which voice client is associated currentlyro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.5.1.3 |
aiClientAPNameName of AP on which voice client is associated currentlyro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.2.5.1.4 |
aiManagedInfoGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14823.2.3.3.1.3 |
aiManagedModeSinceLastSyncTime since last config was appliedro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.3.1 |
aiTrapsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14823.2.3.3.1.200 |
aiTrapObjectsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14823.2.3.3.1.200.1 |
wlsxTrapAPMacAddressThis object is used in the traps to indicate the wired MAC address of an access point, for which the trap is being raised.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.1 |
wlsxTrapAPIpAddressThis object is used in the traps to indicate the IP address of an access point, for which the trap is being raised.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.2 |
wlsxTrapAPBSSIDThis object is used in the traps to indicate the BSSID of the access point, for which the trap is being raised.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.3 |
wlsxTrapEssidThis object is used in the traps to indicate the SSID of the access point, for which the trap is being raised.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.4 |
wlsxTrapTargetAPBSSIDThis object is used in the traps to indicate the BSSID of the access point, for which we are raising the trap. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.5 |
wlsxTrapTargetAPSSIDThis object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.6 |
wlsxTrapTargetAPChannelThis object is used in the traps to indicate the channel of the access point, for which the trap is being raised. If an wlsxr monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.7 |
wlsxTrapNodeMacThis object is used in the traps to indicate the MAC address of a node.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.8 |
wlsxTrapSourceMacThis object is used in the traps to indicate the MAC address of the source.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.9 |
wlsxReceiverMacThis object is used in the traps to indicate the MAC address of the receiver.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.10 |
wlsxTrapTransmitterMacThis object is used in the traps to indicate the MAC address of the transmitter.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.11 |
wlsxTrapReceiverMacThis object is used in the traps to indicate the MAC address of the receiver.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.12 |
wlsxTrapSnrThis object is used in the traps to indicate the Signal to Noise ratio.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.13 |
wlsxTrapSignatureNameThis object is used in the traps to indicate the Signature Name.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.14 |
wlsxTrapFrameTypeThis object is used in the traps to indicate the Frame Typero ArubaFrameType .1.3.6.1.4.1.14823.2.3.3.1.200.1.15 |
wlsxTrapAddressTypeThis object is used in the traps to indicate the Address type.ro ArubaAddressType .1.3.6.1.4.1.14823.2.3.3.1.200.1.16 |
wlsxTrapAPLocationThis object is used in the traps to indicate the Location of the AP.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.17 |
wlsxTrapAPChannelThis object is used in the traps to indicate the Current Channel.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.18 |
wlsxTrapAPTxPowerThis object is used in the traps to indicate the AP Transmit Power.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.19 |
wlsxTrapMatchedMacThis object is used in the traps to indicate the MAC addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.20 |
wlsxTrapMatchedIpThis object is used in the traps to indicate the IP addressro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.21 |
wlsxTrapRogueIfoURLThis object is used to point to the WEBUI Rogue AP information URL.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.22 |
wlsxTrapVlanIdThis object is used in the traps to indicate the VLAN Id.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.23 |
wlsxTrapAdminStatusThis object is used in the traps to indicate the admin status of VLAN.ro ArubaEnableValue .1.3.6.1.4.1.14823.2.3.3.1.200.1.24 |
wlsxTrapOperStatusThis object is used in the traps to indicate the admin status of VLAN.ro ArubaOperStateValue .1.3.6.1.4.1.14823.2.3.3.1.200.1.25 |
wlsxTrapAuthServerNameThis object is used in the traps to indicate the Authentication Server used for Authentication.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.26 |
wlsxTrapAuthServerTimeoutThis object is used in the traps to indicate the Authentication Server Timeout.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.27 |
wlsxTrapCardSlotThis object is used in the traps to indicate the Slot in which this card is present.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.28 |
wlsxTrapTemperatureValueThis object is used in the traps to indicate the Temperature Value.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.29 |
wlsxTrapProcessNameThis object is used in the traps to indicate the Process name.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.30 |
wlsxTrapFanNumberThis object is used in the traps to indicate the Fan Number.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.31 |
wlsxTrapVoltageTypeThis object is used in the traps to indicate the type of Voltage.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.32 |
wlsxTrapVoltageValueThis object is used in the traps to indicate the voltage value in Float.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.33 |
wlsxTrapStationBlackListReasonThe Reason for which a station is black listed.ro ArubaBlackListReason .1.3.6.1.4.1.14823.2.3.3.1.200.1.34 |
wlsxTrapSpoofedIpAddressThis object is used in a trap to identify a spoofed IP address.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.35 |
wlsxTrapSpoofedOldPhyAddressThis object is used in a trap to identify an old MAC address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.36 |
wlsxTrapSpoofedNewPhyAddressThis object is used in a trap to identify a New MAC address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.37 |
wlsxTrapDBNameThis object is used in a trap to identify name of the database.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.38 |
wlsxTrapDBUserNameThis object is used in a trap to identify name of the database user.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.39 |
wlsxTrapDBIpAddressThis object is used in a trap to identify the IpAddress of the Database.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.40 |
wlsxTrapDBTypeThis object is used in a trap to identify the port of the user.ro ArubaDBType .1.3.6.1.4.1.14823.2.3.3.1.200.1.41 |
wlsxTrapVrrpIDThis object contains the Virtual Router Identifier.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.42 |
wlsxTrapVrrpMasterIpThis object contains the Master IP address.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.43 |
wlsxTrapVrrpOperStateThis object represents the VRRP Operational state.ro ArubaVrrpState .1.3.6.1.4.1.14823.2.3.3.1.200.1.44 |
wlsxTrapESIServerGrpNameThis object represents the External Services Interface (ESI) Server Group namero DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.45 |
wlsxTrapESIServerNameThis object represents the External Services Interface (ESI) Server Namero DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.46 |
wlsxTrapESIServerIpAddressThis object represents the External Services Interface (ESI) Server IP addressro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.47 |
wlsxTrapLicenseDaysRemainingThis object represents number of the days remaining prior to a license expiry.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.48 |
wlsxTrapSwitchIpThis object represents the controller IP address.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.49 |
wlsxTrapSwitchRoleThis object represents the Role of the controller.ro ArubaSwitchRole .1.3.6.1.4.1.14823.2.3.3.1.200.1.50 |
wlsxTrapUserIpAddressThis object represents IP address of the User.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.51 |
wlsxTrapUserPhyAddressThis object represents MAC address of the User.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.52 |
wlsxTrapUserNameThis object represents the user name.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.53 |
wlsxTrapUserRoleThis object represents the Authentication method of the user.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.54 |
wlsxTrapUserAuthenticationMethodThis object represents the Authentication method of the user.ro ArubaAuthenticationMethods .1.3.6.1.4.1.14823.2.3.3.1.200.1.55 |
wlsxTrapAPRadioNumberThis object represents the radio number.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.56 |
wlsxTrapRogueInfoURLThis object is used to point to the WEBGUI Rogue AP information URL.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.57 |
wlsxTrapInterferingAPInfoURLThis object is used to point to the WEBGUI Rogue interfering AP information URL.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.58 |
wlsxTrapPortNumberThis object is used in the traps to indicate the port number.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.59 |
wlsxTrapTimeThis object is used in all the enterprise traps to indicate the the time when the trap is generated on the controller.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.60 |
wlsxTrapHostIpThis object represents the Trap host.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.61 |
wlsxTrapHostPortThis object represents the Trap host port.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.62 |
wlsxTrapConfigurationIdThis object represents the ID of the configuration, to be used in traps.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.63 |
wlsxTrapCTSURLThis object represents the URL from which the transfer should happen.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.64 |
wlsxTrapCTSTransferTypeThis object represents the transfer type, upload or download.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.65 |
wlsxTrapConfigurationStateThis object represents state of the configuration transfer.ro ArubaConfigurationState .1.3.6.1.4.1.14823.2.3.3.1.200.1.66 |
wlsxTrapUpdateFailureReasonThis object represents the reason for the update failure.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.67 |
wlsxTrapUpdateFailedObjThis variable represents the AMAPI object which is the reason for the the update failure.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.68 |
wlsxTrapTableEntryChangeTypeThis object represents type of the configuration change.ro ArubaConfigurationChangeType .1.3.6.1.4.1.14823.2.3.3.1.200.1.69 |
wlsxTrapGlobalConfigObjThis variable represents the AMAPI object corresponding to the global configuration change.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.70 |
wlsxTrapTableGenNumberThis object represents generation number of a table. Used in the MMS, to keep track of the table content changes.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.71 |
wlsxTrapLicenseIdThis object is used in the traps to indicate the license ID.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.72 |
wlsxTrapConfidenceLevelThis object is used in the traps to indicate the Confidence Level as a percentagero Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.73 |
wlsxTrapMissingLicensesThis variable indicates any licenses that are not present during a configuration updatero DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.74 |
wlsxVoiceCurrentNumCdrThis object represents the number of CDRs in buffer.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.75 |
wlsxTrapTunnelIdThis Object represents the tunnel ID.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.76 |
wlsxTrapTunnelStatusThis Object represents the tunnel Status.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.77 |
wlsxTrapTunnelUpReasonThis Object represents the tunnel up reason.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.78 |
wlsxTrapTunnelDownReasonThis Object represents the tunnel down reason.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.79 |
wlsxTrapApSerialNumberThis object represents the AP Serial Number.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.80 |
wlsxTrapTimeStrThis object represents the Time in String format.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.81 |
wlsxTrapMasterIpThis object represents the master IP address.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.82 |
wlsxTrapLocalIpThis object represents the Local IP address.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.83 |
wlsxTrapMasterNameThis object represents the master controller name.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.84 |
wlsxTrapLocalNameThis object represents the local controller name.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.85 |
wlsxTrapPrimaryControllerIpThis object represents the IP address of the AP's primary controller.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.86 |
wlsxTrapBackupControllerIpThis object represents the IP address of the AP's backup controller.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.87 |
wlsxTrapSpoofedFrameTypeThis object is used in the traps to indicate the Spoofed Frame Typero DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.88 |
wlsxTrapAssociationTypeThis object is used in the traps to indicate the type of associationro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.89 |
wlsxTrapDeviceIpAddressThis object represents the IP address of a device seen by an AP.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.90 |
wlsxTrapDeviceMacThis object represents the MAC address of a device seen by an AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.91 |
wlsxTrapVcIpAddressThis object represents the Ip Address of a Voice client.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.92 |
wlsxTrapVcMacAddressThis object represents the MAC address of a Voice client.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14823.2.3.3.1.200.1.93 |
wlsxTrapAPNameThis object is used in the traps to indicate the Name of the AP.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.94 |
wlsxTrapApModeThis Object represents the AP Mode.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.95 |
wlsxTrapAPPrevChannelThis object is used in the traps to indicate the Previous Channel.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.96 |
wlsxTrapAPPrevChannelSecThis object is used in the traps to indicate the Previous Secondary Channel.ro ArubaHTExtChannel .1.3.6.1.4.1.14823.2.3.3.1.200.1.97 |
wlsxTrapAPPrevTxPowerThis object is used in the traps to indicate previous AP Transmit Power.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.98 |
wlsxTrapAPCurModeThis Object represents the APs Current Mode.ro ArubaAccessPointMode .1.3.6.1.4.1.14823.2.3.3.1.200.1.99 |
wlsxTrapAPPrevModeThis Object represents the APs Previous Mode.ro ArubaAccessPointMode .1.3.6.1.4.1.14823.2.3.3.1.200.1.100 |
wlsxTrapAPARMChangeReasonThis Object represents the APs Previous Mode.ro ArubaARMChangeReason .1.3.6.1.4.1.14823.2.3.3.1.200.1.101 |
wlsxTrapAPChannelSecThis object is used in the traps to indicate the Current Secondary Channel.ro ArubaHTExtChannel .1.3.6.1.4.1.14823.2.3.3.1.200.1.102 |
wlsxTrapUserAttributeChangeTypeThis object represents type of the configuration change.ro ArubaConfigurationChangeType .1.3.6.1.4.1.14823.2.3.3.1.200.1.103 |
wlsxTrapApControllerIpIP address of the controller to which the AP is (or was most recently) registered.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.104 |
wlsxTrapApMasterStatusStatus of the AP as seen by the master when the status changes.ro ArubaAPMasterStatus .1.3.6.1.4.1.14823.2.3.3.1.200.1.105 |
wlsxTrapCaNameThis object is used in the traps to indicate the name of the trustpoint.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.106 |
wlsxTrapCrlNameThis object is used in the traps to indicate the name of the crl.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.107 |
wlsxTrapCountThis object represents the number of occurrence of this trap.ro Integer32 .1.3.6.1.4.1.14823.2.3.3.1.200.1.108 |
wlsxTrapAPPreviousUplinkTypeThis object specifies the up link type for an AP.ro ArubaAPUplinkType .1.3.6.1.4.1.14823.2.3.3.1.200.1.130 |
wlsxTrapAPPreviousUplinkActiveTimeThis object specifies the up link type for an AP.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.14823.2.3.3.1.200.1.131 |
wlsxTrapAPActiveUplinkTypeThis object specifies the up link type for an AP.ro ArubaAPUplinkType .1.3.6.1.4.1.14823.2.3.3.1.200.1.132 |
wlsxTrapAPUplinkChangeReasonThis object specifies the up link change reason.ro ArubaAPUplinkChangeReason .1.3.6.1.4.1.14823.2.3.3.1.200.1.133 |
wlsxTrapAPManagedModeConfigFailureThis object indicates the error for the failure of config apply on IAP.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.138 |
wlsxTrapAuthServerAddressThis object is used in the traps to indicate the Authentication Server IP used for Authentication.ro IpAddress .1.3.6.1.4.1.14823.2.3.3.1.200.1.139 |
wlsxTrapPortalServerNameThis object is used in the traps to indicate the Captive Portal Server used for Authentication.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.140 |
wlsxTrapPortalServerAddressThis object is used in the traps to indicate the Captive Portal Server IP or host name used for Authentication.ro DisplayString .1.3.6.1.4.1.14823.2.3.3.1.200.1.141 |
wlsxTrapPortalServerDownReasonThis object specifies the captive portal server down reason.ro ArubaPortalServerDownReason .1.3.6.1.4.1.14823.2.3.3.1.200.1.142 |
aiTrapDefinitionsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14823.2.3.3.1.200.2 |
wlsxNodeRateAnomalyThis trap indicates that a node is exceeding the threshold set for the frame type. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1003 |
wlsxNUserEntryCreatedThis trap indicates that a new user was created. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1014 |
wlsxNUserEntryDeletedThis trap indicates that a user was deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1015 |
wlsxNUserEntryAuthenticatedThis trap indicates that a user is Authenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1016 |
wlsxNUserEntryDeAuthenticatedThis trap indicates that a user is Deauthenticated. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1017 |
wlsxNUserAuthenticationFailedThis trap indicates that a user authentication has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1018 |
wlsxNAuthServerReqTimedOutThis trap indicates that the authentication server request timed out. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1019 |
wlsxNAuthServerTimedOutThis trap indicates that the authentication server timed out. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1020 |
wlsxNAuthServerIsUpThis trap indicates that an authentication server is up. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1021 |
wlsxNAccessPointIsUpA Trap which indicates that an access point up. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1040 |
wlsxNAccessPointIsDownA Trap which indicates that an access point down. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1041 |
wlsxNChannelChangedThis trap indicates that an access point at Location wlsxTrapAPLocation has changed the channel. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1043 |
wlsxNStationAddedToBlackListThis trap indicates that the station is black listed. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1044 |
wlsxNStationRemovedFromBlackListThis trap indicates that the station is removed from the black list. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1045 |
wlsxNRadioAttributesChangedA Trap which indicates changes in the Radio attributes of an access point. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1049 |
wlsxUnsecureAPDetectedThis trap indicates that an unauthorized access point is connected to the wired network. The access point is declared Rogue because it was matched to a MAC address. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1053 |
wlsxUnsecureAPResolvedThis trap indicates that a previously detected access point, classified as Rogue, is no longer present in the network. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1054 |
wlsxStaImpersonationThis trap indicates that an AM detected Station Impersonation. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1055 |
wlsxReservedChannelViolationThis trap indicates that an AM detected an access point which is violating the Reserved Channel configuration. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1056 |
wlsxValidSSIDViolationThis trap indicates that an AP has detected an access point is violating Valid SSID configuration by using an SSID that is reserved for use by a valid AP only. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1057 |
wlsxChannelMisconfigurationThis trap indicates that an AP detected an access point that has a channel misconfiguration because it is using a channel that is not valid. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1058 |
wlsxOUIMisconfigurationThis trap indicates that an AP detected an access point that has an OUI misconfiguration because it is using an OUI that is not valid. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1059 |
wlsxSSIDMisconfigurationThis trap indicates that an AP detected an access point that has an SSID misconfiguration because it is using an SSID that is not valid. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1060 |
wlsxShortPreableMisconfigurationThis trap indicates that an access point has bad Short preamble configuration. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1061 |
wlsxWPAMisconfigurationThis trap indicates that an AP detected an access point that is misconfigured because it is not using WPA. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1062 |
wlsxAdhocNetworkDetectedThis trap indicates that an AM has detected an Ad hoc network. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1063 |
wlsxAdhocNetworkRemovedThis trap indicates that a previously detected Ad hoc Network is no longer present in the network. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1064 |
wlsxStaPolicyViolationThis trap indicates that Protection was enforced because a valid station's association to a non-valid access point violated Valid Station policy. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0019 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1065 |
wlsxRepeatWEPIVViolationThis trap indicates that an AP detected that a valid access point is using the same WEP initialization vector in consecutive packets. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1066 |
wlsxWeakWEPIVViolationThis trap indicates that an AP detected that a valid access point is using a Weak WEP initialization vector. For more info check: http://www.wve.org/entries/show/WVE-2005-0021 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1067 |
wlsxChannelInterferenceDetectedThis trap indicates that an AP has detected channel interference. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1068 |
wlsxChannelInterferenceClearedThis trap indicates that a previously detected channel interference is no longer present. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1069 |
wlsxAPInterferenceDetectedThis trap indicates that an AP has detected interference for an access point. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1070 |
wlsxAPInterferenceClearedThis trap indicates that the previously detected interference for an access point is no longer present. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1071 |
wlsxStaInterferenceDetectedThis trap indicates that an AP has detected interference for a station. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1072 |
wlsxStaInterferenceClearedThis trap indicates that the previously detected interference for a station is no longer present. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1073 |
wlsxFrameRetryRateExceededThis trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Retry Rate. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1074 |
wlsxFrameReceiveErrorRateExceededThis trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Receive Error Rate. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1075 |
wlsxFrameFragmentationRateExceededThis trap indicates that an AP detected that an access point exceeded the configured upper threshold for Frame Fragmentation Rate. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1076 |
wlsxFrameBandWidthRateExceededThis trap indicates that an AP detected that a station or access point has exceeded the configured upper threshold for Bandwidth rate. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1077 |
wlsxFrameLowSpeedRateExceededThis trap indicates that an AP detected that a station has exceeded the configured upper threshold for Low speed rate. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1078 |
wlsxFrameNonUnicastRateExceededThis trap indicates that an AP detected that a station has exceeded the configured upper threshold for Non Unicast traffic rate. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1079 |
wlsxLoadbalancingEnabledThis trap indicates that an AM is reporting that an AP has enabled Load balancing. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1080 |
wlsxLoadbalancingDisabledThis trap indicates that an AM is reporting that an AP has enabled Load balancing. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1081 |
wlsxChannelFrameRetryRateExceededThis trap indicates that an AP has detected that the configured upper threshold for Frame Retry Rate was exceeded on a channel. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1082 |
wlsxChannelFrameFragmentationRateExceededThis trap indicates that an AP has detected that the configured upper threshold for Frame Fragmentation Rate was exceeded on a channel. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1083 |
wlsxChannelFrameErrorRateExceededThis trap indicates that an AP has detected that the configured upper threshold for Frame Receive Error Rate was exceeded on a channel. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1084 |
wlsxSignatureMatchAPThis trap indicates that an AP detected a signature match in a frame from an access point. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1085 |
wlsxSignatureMatchStaThis trap indicates that an AP detected a signature match in a frame from a Station. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1086 |
wlsxChannelRateAnomalyThis trap indicates that an AP detected frames on a channel which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1087 |
wlsxNodeRateAnomalyAPThis trap indicates that an AP detected frames transmitted or received by an access point, which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1088 |
wlsxNodeRateAnomalyStaThis trap indicates that an AP detected frames transmitted or received by a node, which exceed the configured IDS rate threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1089 |
wlsxEAPRateAnomalyThis trap indicates that the rate of EAP Handshake packets received by an AP has exceeded the configured IDS EAP Handshake rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0049 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1090 |
wlsxSignalAnomalyThis trap indicates that an AM detected a Signal Anomaly. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1091 |
wlsxSequenceNumberAnomalyAPThis trap indicates that an AM received packets from an AP which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1092 |
wlsxSequenceNumberAnomalyStaThis trap indicates that an AM received packets from a Node which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1093 |
wlsxDisconnectStationAttackThis trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1094 |
wlsxApFloodAttackThis trap indicates that the number of potential fake APs detected by an AP has exceeded the configured IDS threshold. This is the total number of fake APs observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1095 |
wlsxAdhocNetworkThis trap indicates that an AM detected an Ad hoc Network. An Station is connected to an ad hoc AP. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1096 |
wlsxWirelessBridgeThis trap indicates that an AP detected a Wireless Bridge when a WDS frame was seen between the transmitter and receiver addresses. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1097 |
wlsxInvalidMacOUIAPThis trap indicates that an AP detected an invalid MAC OUI in the BSSID of a frame. An invalid MAC OUI suggests that the frame may be spoofed. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1098 |
wlsxInvalidMacOUIStaThis trap indicates that an AP detected an invalid MAC OUI in the SRC or DST address of a frame. An invalid MAC OUI suggests that the frame may be spoofed. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1099 |
wlsxWEPMisconfigurationThis trap indicates that an AP detected an access point that is misconfigured because it does not have Privacy enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1100 |
wlsxStaRepeatWEPIVViolationThis trap indicates that an AP detected that a valid station is using the same WEP initialization vector in consecutive packets. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1101 |
wlsxStaWeakWEPIVViolationThis trap indicates that an AP detected that a valid station is using a Weak WEP initialization vector. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1102 |
wlsxStaAssociatedToUnsecureAPThis trap indicates that an AM detected a client associated with a Rogue access point. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1103 |
wlsxStaUnAssociatedFromUnsecureAPThis trap indicates that a previously detected rogue access point association is no longer present. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1104 |
wlsxAdhocNetworkBridgeDetectedThis trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1105 |
wlsxInterferingApDetectedThis trap indicates that an AP detected an access point classified as Interfering. The access point is declared Interfering because it is neither authorized or classified as Rogue. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1106 |
wlsxColdStartAn enterprise version of cold start trap, which contains the controller time stamp. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1111 |
wlsxWarmStartAn enterprise version of warm start trap, which contains the controller time stamp. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1112 |
wlsxAPImpersonationThis trap indicates that an AP detected AP Impersonation because the number of beacons seen has exceeded the expected number by the configured percentage threshold. The expected number is calculated based on the Beacon Interval Field in the Beacon frame. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1113 |
wlsxNAuthServerIsDownThis trap indicates that an authentication server is down. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1115 |
wlsxWindowsBridgeDetectedThis trap indicates that an AM has detected a station that is bridging from a wireless network to a wired network NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1129 |
wlsxSignAPNetstumblerThis trap indicates that an AP detected a signature match for Netstumbler from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0025 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1134 |
wlsxSignStaNetstumblerThis trap indicates that an AP detected a signature match for Netstumbler from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0025 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1135 |
wlsxSignAPAsleapThis trap indicates that an AP detected a signature match for ASLEAP from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0027 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1136 |
wlsxSignStaAsleapThis trap indicates that an AP detected a signature match for ASLEAP from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0027 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1137 |
wlsxSignAPAirjackThis trap indicates that an AP detected a signature match for AirJack from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0018 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1138 |
wlsxSignStaAirjackThis trap indicates that an AP detected a signature match for AirJack from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0018 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1139 |
wlsxSignAPNullProbeRespThis trap indicates that an AP detected a signature match for Null-Probe-Response from an access point. For more info check: http://www.wve.org/entries/show/WVE-2006-0064 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1140 |
wlsxSignStaNullProbeRespThis trap indicates that an AP detected a signature match for Null-Probe-Response from a Station. For more info check: http://www.wve.org/entries/show/WVE-2006-0064 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1141 |
wlsxSignAPDeauthBcastThis trap indicates that an AP detected a signature match for Deauth-Broadcast from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1142 |
wlsxSignStaDeauthBcastThis trap indicates that an AP detected a signature match for Deauth-Broadcast from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1143 |
wlsxWindowsBridgeDetectedAPThis trap indicates that an AP is detecting an access point that is bridging from a wireless network to a wired network. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1144 |
wlsxWindowsBridgeDetectedStaThis trap indicates that an AP is detecting a station that is bridging from a wireless network to a wired network. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1145 |
wlsxAdhocNetworkBridgeDetectedAPThis trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1146 |
wlsxAdhocNetworkBridgeDetectedStaThis trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1147 |
wlsxDisconnectStationAttackAPThis trap indicates that an AM detected a station disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1148 |
wlsxDisconnectStationAttackStaThis trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1149 |
wlsxSuspectUnsecureAPDetectedThis trap indicates that an access point, classified as Suspected Rogue, has been detected by a Controller. The AP is suspected to be rogue, with the supplied confidence level, because it was matched to the wired MAC address. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1150 |
wlsxSuspectUnsecureAPResolvedThis trap indicates that a previously detected access point, classified Suspected Rogue, is either no longer present in the network or has changed its state. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1151 |
wlsxHtGreenfieldSupportedThis trap indicates that an AP detected an access point that supports HT Greenfield mode. For more info check: http://www.wve.org/entries/show/WVE-2008-0005 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1157 |
wlsxHT40MHzIntoleranceAPThis trap indicates that an AP is detecting an access point with the HT 40MHz intolerance setting. For more info check: http://www.wve.org/entries/show/WVE-2008-0004 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1158 |
wlsxHT40MHzIntoleranceStaThis trap indicates that the system is detecting an HT 40MHz Intolerance setting from a Station. For more info check: http://www.wve.org/entries/show/WVE-2008-0004 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1159 |
wlsxNAuthServerAllInServiceThis trap indicates that all authentication servers is a server group are brought back in service. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1160 |
wlsxNAdhocNetworkThis trap indicates that an AP detected an ad hoc network where a station is connected to an ad hoc access point. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1161 |
wlsxNAdhocNetworkBridgeDetectedAPThis trap indicates that an AP detected an ad hoc network that is bridging to a wired network. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1162 |
wlsxNAdhocNetworkBridgeDetectedStaThis trap indicates that an AP detected an ad hoc network that is bridging to a wired network. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1163 |
wlsxClientFloodAttackThis trap indicates that the number of potential fake clients detected by an AP has exceeded the configured IDS threshold. This is the total number of fake clients observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1170 |
wlsxValidClientNotUsingEncryptionThis trap indicates that an AP detected an unencrypted data frame between a valid client and an access point. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1171 |
wlsxAdhocUsingValidSSIDThis trap indicates that an AP detected an ad hoc network using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1172 |
wlsxAPSpoofingDetectedThis trap indicates that an AP detected that one of its virtual APs is being spoofed using MAC spoofing. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1173 |
wlsxClientAssociatingOnWrongChannelThis trap indicates that an AP detected a client trying to associate to one of its BSSIDs on the wrong channel. This can be a sign that the BSSID is being spoofed in order to fool the client into thinking the AP is operating on another channel. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1174 |
wlsxNDisconnectStationAttackThis trap indicates that an AP has determined that a client is under Disconnect Attack because the rate of Assoc/Reassoc Response packets received by that client exceeds the configured threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1175 |
wlsxNStaUnAssociatedFromUnsecureAPThis trap indicates that an AP that had previously detected a client association to a Rogue access point is no longer detecting that association. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1176 |
wlsxOmertaAttackThis trap indicates that an AP detected an Omerta attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0053 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1177 |
wlsxTKIPReplayAttackThis trap indicates that an AP detected a TKIP replay attack. If successful this could be the precursor to more advanced attacks. For more info check: http://www.wve.org/entries/show/WVE-2008-0013 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1178 |
wlsxChopChopAttackThis trap indicates that an AP detected a ChopChop attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0038 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1179 |
wlsxFataJackAttackThis trap indicates that an AP detected a FATA-Jack attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0057 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1180 |
wlsxInvalidAddressCombinationThis trap indicates that an AP detected an invalid source and destination combination. For more info check: http://www.wve.org/entries/show/WVE-2008-0011 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1181 |
wlsxValidClientMisassociationThis trap indicates that an AP detected a misassociation between a valid client and an unsafe AP. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1182 |
wlsxMalformedHTIEDetectedThis trap indicates that an AP detected a malformed HT Information Element. This can be the result of a misbehaving wireless driver or it may be an indication of a new wireless attack. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1183 |
wlsxMalformedAssocReqDetectedThis trap indicates that an AP detected a malformed association request with a NULL SSID. For more info check: http://www.wve.org/entries/show/WVE-2008-0010 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1184 |
wlsxOverflowIEDetectedThis trap indicates that an AP detected a management frame with a malformed information element. The declared length of the element is larger than the entire frame containing the element. This may be used to corrupt or crash wireless drivers. For more info check: http://www.wve.org/entries/show/WVE-2008-0008 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1185 |
wlsxOverflowEAPOLKeyDetectedThis trap indicates that an AP detected a key in an EAPOL Key message with a specified length greater than the length of the entire message. For more info check: http://www.wve.org/entries/show/WVE-2008-0009 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1186 |
wlsxMalformedFrameLargeDurationDetectedThis trap indicates that an AP detected an unusually large duration in a wireless frame. This may be an attempt to block other devices from transmitting. For more info check: http://www.wve.org/entries/show/WVE-2005-0051 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1187 |
wlsxMalformedFrameWrongChannelDetectedThis trap indicates that an AP detected a beacon on one channel advertising another channel. This could be an attempt to lure clients away from a valid AP. For more info check: http://www.wve.org/entries/show/WVE-2006-0050 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1188 |
wlsxMalformedAuthFrameThis trap indicates that an AP detected an authentication frame with either a bad algorithm (similar to Fata-Jack) or a bad transaction. For more info check: http://www.wve.org/entries/show/WVE-2006-0057 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1189 |
wlsxCTSRateAnomalyThis trap indicates that the rate of CTS packets received by an AP exceeds the configured IDS threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1190 |
wlsxRTSRateAnomalyThis trap indicates that the rate of RTS packets received by an AP exceeds the configured IDS threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1191 |
wlsxNRogueAPDetectedThis trap indicates that an unauthorized access point is connected to the wired network. The access point is classified as Rogue by the system. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1192 |
wlsxNRogueAPResolvedThis trap indicates that a previously detected access point, classified as Rogue, is either no longer present in the network or it changed its state. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1193 |
wlsxNeighborAPDetectedThis trap indicates that an access point has been classified as a Neighbor by the system. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1194 |
wlsxNInterferingAPDetectedThis trap indicates that an access point has been classified as Interfering by the system. The access point is declared Interfering because it is not authorized, nor has it been classified as a Rogue. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1195 |
wlsxNSuspectRogueAPDetectedThis trap indicates that an access point, classified as Suspected Rogue, is detected by the system. The AP is suspected to be rogue with the supplied confidence level. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1196 |
wlsxNSuspectRogueAPResolvedThis trap indicates that a previously detected access point, classified as Suspected Rogue, is either no longer present in the network or has changed its state. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1197 |
wlsxBlockAckAttackDetectedThis trap indicates that an attempt has been made to deny service to the source address by spoofing a block ACK add request that sets a sequence number window outside the currently used window. For more info check: http://www.wve.org/entries/show/WVE-2008-0006 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1198 |
wlsxHotspotterAttackDetectedThis trap indicates that a new AP has appeared immediately following a client probe request. This is indicative of the Hotspotter tool or similar that attempts to trap clients with a fake hotspot or other wireless network. For more info check: http://www.wve.org/entries/show/WVE-2005-0054 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1199 |
wlsxNSignatureMatchThis trap indicates that an AP detected a signature match in a frame. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1200 |
wlsxNSignatureMatchNetstumblerThis trap indicates that an AP detected a signature match for Netstumbler in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0025 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1201 |
wlsxNSignatureMatchAsleapThis trap indicates that an AP detected a signature match for ASLEAP in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0027 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1202 |
wlsxNSignatureMatchAirjackThis trap indicates that an AP detected a signature match for Airjack in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0018 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1203 |
wlsxNSignatureMatchNullProbeRespThis trap indicates that an AP detected a signature match for Null-Probe-Response in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0064 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1204 |
wlsxNSignatureMatchDeauthBcastThis trap indicates that an AP detected a signature match for Deauth-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1205 |
wlsxNSignatureMatchDisassocBcastThis trap indicates that an AP detected a signature match for Disassoc-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0046 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1206 |
wlsxNSignatureMatchWellenreiterThis trap indicates that an AP detected a signature match for Wellenreiter in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0058 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1207 |
wlsxAPDeauthContainmentThis trap indicates that an AP has attempted to contain an access point by disconnecting its client. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1208 |
wlsxClientDeauthContainmentThis trap indicates that an AP has attempted to contain a client by disconnecting it from the AP that it is associated with. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1209 |
wlsxAPWiredContainmentThis trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1210 |
wlsxClientWiredContainmentThis trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1211 |
wlsxAPTaggedWiredContainmentThis trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1212 |
wlsxClientTaggedWiredContainmentThis trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1213 |
wlsxTarpitContainmentThis trap indicates that an AP has attempted to contain an access point by moving a client that is attempting to associate to it to a tarpit. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1214 |
wlsxAPChannelChangeThis trap indicates that an AP changed its channel. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1216 |
wlsxAPPowerChangeThis trap indicates that an AP changed its transmit power level. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1217 |
wlsxAPModeChangeThis trap indicates that an AP changed its mode from AP to APMonitor or vice versa. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1218 |
wlsxUserEntryAttributesChangedThis trap indicates that the user entry attributes have changed. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1219 |
wlsxPowerSaveDosAttackThis trap indicates that an AP detected a Power Save DoS attack. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1220 |
wlsxNAPMasterStatusChangeThis trap indicates that the status of the AP as seen by the master controller has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1221 |
wlsxNAdhocUsingValidSSIDThis trap indicates that an AP detected an ad hoc network node using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1222 |
wlsxMgmtUserAuthenticationFailedThis trap indicates that a management user authentication has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1224 |
wlsxAPActiveUplinkChangedWhen the active uplink of an AP changes, a notification is sent to the Management Entity with the new uplink type NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1252 |
wlsxAPManagedModeConfigFailureTrapIndicated failure in applying config. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1255 |
wlsxNAuthServerAcctTimedOutThis trap indicates that the authentication server accounting timed out. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1256 |
wlsxPortalServerDownThis trap indicates that the portal server is down. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1259 |
wlsxPortalServerUpThis trap indicates that the portal server is up. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1260 |
wlsxIAPVoiceClientLocationUpdateThe trap represents a IAP voice client location update. NOTIFICATION-TYPE .1.3.6.1.4.1.14823.2.3.3.1.200.2.1262 |