ADIC-MANAGEMENT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ADIC-MANAGEMENT-MIB.
457
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
457 total| Object Name |
|---|
management OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20 |
RFC1155-SMI Unknown .1.3.6.1.4.1.2.6.159.201.5.4.20 |
physLibraryActivity TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.100 |
physLibraryOnlineStatusChange TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.101 |
physLibraryDoorStatusChange TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.102 |
ieStationDoorStatusChange TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.103 |
moveMediaCompleteA piece of media has been move from one
location to another.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
phStorageElementAddr - source element address
phStorageElementAddr - destination element address TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.104 |
tapeDriveAddedA tape drive was added to the library.
This trap is issued when a tape drive previously unknown
to the library becomes known.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
phDriveRow - row component of the drive's physical location
in the library. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.105 |
tapeDriveRemovedA tape drive was removed from the library.
This trap is issued when a tape drive is removed from
library's configuration.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
phDriveRow - row component of the drive's physical location
in the library. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.106 |
mediaMountedMedia was mounted in the tape drive indicated in the trap
payload.
This trap is issued upon every mount operation.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
phDriveRow - row component of the drive's physical location
in the library. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.107 |
mediaDismountedMedia was dismounted in the tape drive indicated in the trap
payload.
This trap is issued upon every dismount operation.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
phDriveRow - row component of the drive's physical location
in the library.
phDriveMbytesRead - over lifetime of drive
phDriveMbytesWritten - over lifetime of drive TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.108 |
ieStationInventoryPerformedAn inventory operation has been performed
on an I/E station. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.109 |
rcuReadyThe RCU indicated in the payload has
transitioned from the NotReady state
to the Ready state. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.110 |
rcuNotReadyThe RCU indicated in the payload has
transitioned from the NotReady state
to the Ready state. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.111 |
driveActivityUpdateDrive activity integrated over a fixed
time period. Currently, the time period
is one hour. NOTE: the drive is identified
by the instance OID contained in the
phHourlyMBytesRead, phHourlyMBytesWritten,
and phHourlyWritten varbinds. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.112 |
driveBrickFwUpdateSuccessDrive brick's firmware was successfully updated.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
trapSummaryText - brief message about the update
phDriveSerialNumber - the drive serial number. The
OID of the varbind encoded in
the trap payload must be the
full OID, column OID plus indices.
phDriveFirmwareVersion - the drive firmware version
identifier. The OID of the varbind
encoded in the trap payload must be
the full OID, column OID plus indices. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.113 |
driveBrickFwUpdateFailureAttempt to update drive brick's firmware has failed.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
trapSummaryText - brief message about the update
phDriveSerialNumber - the drive serial number. The
OID of the varbind encoded in
the trap payload must be the
full OID, column OID plus indices.
phDriveFirmwareVersion - the drive firmware version
identifier. The OID of the varbind
encoded in the trap payload must be
the full OID, column OID plus indices. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.114 |
physLibraryConfigurationChangeThe physical configuration of the library has
been changed, possibly invalidating the data
in the management application's model. For
example, an LTO magazine swapped for a DLT
magazine. The management application should
repopulate its data model. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.115 |
physLibraryRESChangeThe physical library managers issues this trap
when it detects that the Read Element Status data
has changed. This generally occurs after an
inventory. The range of elements specified
by the last two varbinds may represent storage
drive, or I/E elements. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.116 |
driveBrickFwUpdateStartDrive brick firmware update has started.
componentId - identifies MCB
trapSequenceNumber - generic sequence number
trapSeverity - should be informational(5)
trapSummaryText - brief message about the update
phDriveSerialNumber - the drive serial number. The
OID of the varbind encoded in
the trap payload must be the
full OID, column OID plus indices. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.117 |
logicalLibraryActivity TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.200 |
logicalLibraryCreated TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.201 |
logicalLibraryModified TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.202 |
logicalLibraryDeleted TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.203 |
logicalLibraryOnlineStatusChange TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.204 |
connectivityGroupStatusChangeThe overall state of the connectivity system
status group has changed. The present state of
the connectivity status group is given by the
value of the rasStatusGroupStatus object in the
trap payload. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.400 |
controlGroupStatusChangeThe overall state of the control system
status group has changed. The present state of
the control status group is given by the value of
the rasStatusGroupStatus object in the trap
payload. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.401 |
coolingGroupStatusChangeThe overall state of the cooling system
status group has changed. The present state of
the cooling status group is given by the value of
the rasStatusGroupStatus object in the trap
payload. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.402 |
drivesAndMediaGroupStatusChangeThe overall state of the drives and media system
status group has changed. The present state of
the drives and media status group is given by the
value of the rasStatusGroupStatus object in the trap
payload. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.403 |
powerGroupStatusChangeThe overall state of the power system status
group has changed. The present state of the
power status group is given by the value of
the rasStatusGroupStatus object in the trap
payload. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.404 |
roboticsGroupStatusChangeThe overall state of the robotics system status
group has changed. The present state of the
robotics status group is given by the value of
the rasStatusGroupStatus object in the trap
payload. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.405 |
rasEventNotificationA RAS event has occurred, possibly requiring
action by the management application. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.406 |
logRetrievalCompleteIndicates that the system has retrieved
all remote log files as part of the capture
snapshot procedure. TRAP-TYPE .1.3.6.1.4.1.2.6.159.201.5.4.20.0.500 |
globalStatus OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.10 |
globalStatusTable SEQUENCE OF GlobalStatusEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10 |
globalStatusEntry GlobalStatusEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1 |
roleThe role of this MCB in the
management hierarchy.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.1 |
statusStatus of this MCB.ro AdicAgentStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.2 |
systemDateAndTimeCurrent time as set on system realtime
clock. Also allows system realtime clock
to be set.rw AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.3 |
networkTimeServer1IP address of the time server to be used.rw IpAddress .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.4 |
networkTimeProtocolProtocol to use when with network time server.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.5 |
networkTimeEnableEnable/disabled the use of a network time server.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.6 |
managementMibVersionVersion of the ADIC-MANAGEMENT-MIB on which this
agent is based.ro AdicMibVersion .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.7 |
enableDaylightSavingsTimeEnable automatic adjustment of the system date
and time for daylight savings time.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.8 |
networkTimeServer2IP address of the second time server to be used.
Multiple time servers may be used for redundancy
and (or) improved time accuracy.rw IpAddress .1.3.6.1.4.1.2.6.159.201.5.4.20.10.10.1.9 |
globalEthernetManager OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.15 |
globalEthernetTableSome Ethernet settings/switches. Routing tables
are part of MIB-II, so we don't include them here. SEQUENCE OF GlobalEthernetEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10 |
globalEthernetEntry GlobalEthernetEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1 |
mcbHostNameHost name of this MCB.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.1 |
ipAddressIP Address of this MCB's external Ethernet port.rw IpAddress .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.2 |
dhcpStatusState of DHCP support.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.3 |
ipAddressSubnetMaskRead-Write version of MIB-II ipAdEntNetMask Object.
** Description clause from MIB-II text **
The subnet mask associated with the IP address of
this entry. The value of the mask is an IP
address with all the network bits set to 1 and all
the hosts bits set to 0.rw IpAddress .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.4 |
speedAutoNegotiationEnables/disables automatic Ehternet speed
negotiation.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.5 |
preferredSpeedThe preferred Ethernet speed for this
Ethernet port.rw AdicEthernetSpeed .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.6 |
actualSpeedThe actual (negotiated) speed for this
Ethernet port.ro AdicEthernetSpeed .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.7 |
ethernetDuplexThe duplex setting for this Ethernet port.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.15.10.1.8 |
systemManager OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.20 |
systemManagerTable SEQUENCE OF SystemManagerEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.20.10 |
systemManagerEntryThe MCB System Manager (MSM) provides the high level
system management of the MCB. The primary role of the
MSM is to configure, initialize, and maintain the
software processes running on the MCB. SystemManagerEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.20.10.1 |
softwareComponentIndexIdentifies which piece of MCB software
is being addressed.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.20.10.1.1 |
processRowStatusRow status object for creating/deleting
system components.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.20.10.1.2 |
processPhysicalMemoryThe size in kilobytes of the actual software
process binary.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.20.10.1.3 |
processResidentMemoryThe size in kilobytes of the software process
portion that is currently resident in memory.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.20.10.1.4 |
softwareInstallationTableThis table controls installation of software
packages/updates. SEQUENCE OF SoftwareInstallationEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20 |
softwareInstallationEntry SoftwareInstallationEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1 |
installPackageNameFilename and path of the package to be installed.
The management application writes the filename here,
which initiates the update process.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.1 |
installProcessStatusok - installation successful - this is the intial state
inProgress - software package in being installed
failed - software package installation failed. The
status should return failed until another
write to installPackageFilename.
updateAborted - software installation was cancel and system
reverts back to previous versionro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.2 |
installCommanddownload - copy firmware bundle to MCB but do not install
install - commence installation (could be current bundle or
previously downloaded bundle)
abort - abort installation in progress
rollback - rollback to the previous version of the system
identified by the value in the previousFirmwareVersion field.
timeEstimate - provides a estimate on the overall download time
for a previously downloaded bundlerw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.3 |
installStatusTextIndicates time to complete the entire installation:
example: Estimated time to complete download xx minutesro DisplayString .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.4 |
currentFirmwareVersionFirmware revision currently on the i2000.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.5 |
previousFirmwareVersionPrevious firmware revision on the i2000 that is
available for rollback.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.6 |
downloadedFirmwareVersionIdentifier for a the bundle that was previously
downloaded to the i2000 but not installed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.7 |
componentsInBundleIdentifies the components being installed with this bundle
**********************************************************
(LSB) bit 0 - MCB
bit 1 - CMB
bit 2 - RCU
bit 3 - FCB
bit 4 - AMCro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.8 |
mcbInstallStatusTextProvides detailed information about the MCB component install
Example:
download status (inprogress, complete, failed, not being upgraded) : current component : time to complete MCBro DisplayString .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.9 |
cmbInstallStatusTextProvides detailed information about the CMB component install
Example:
download status (inprogress, complete, failed, not being upgraded) : current CMB : time to complete CMB/sro DisplayString .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.10 |
rcuInstallStatusTextProvides detailed information about the RCU component install
Example:
download status (inprogress, complete, failed, not being upgraded) : current component : time to complete RCUro DisplayString .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.11 |
fcbInstallStatusTextProvides detailed information about the FCB component install
Example:
download status (inprogress, complete, failed, not being upgraded) : current fcb : time to complete FCB/sro DisplayString .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.12 |
amcInstallStatusTextProvides detailed information about the AMC component install
Example:
download status (inprogress, complete, failed, not being upgraded) : current component : time to complete AMCro DisplayString .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.13 |
mcbInstallProcessStatusro AdicInstallStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.14 |
cmbInstallProcessStatusro AdicInstallStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.15 |
rcuInstallProcessStatusro AdicInstallStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.16 |
fcbInstallProcessStatusro AdicInstallStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.17 |
amcInstallProcessStatusro AdicInstallStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.20.20.1.18 |
persistentData OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.30 |
persistentDataTable SEQUENCE OF PersistentDataEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.30.10 |
persistentDataEntry PersistentDataEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.30.10.1 |
capacityThe number of kilobytes of file space
on this MCB.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.30.10.1.1 |
freeSpaceThe number of kilobytes of availble (unused)
file space on this MCB.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.30.10.1.2 |
security OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.40 |
userTable** This table is obsolete. **obsolete SEQUENCE OF UserEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.40.20 |
userEntry** This entry object is obsolete. **obsolete UserEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.40.20.1 |
userName** This object is obsolete. **
User's name.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.40.20.1.1 |
userRowStatus** This object is obsolete. **
Standard Row Status object. Used primarily to
delete users.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.40.20.1.2 |
userGroup** This object is obsolete. **
User's group.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.40.20.1.3 |
userPassword** This object is obsolete. **
User's password.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.40.20.1.4 |
userLibAccessList** This object is obsolete. **
Delimited list of logical library identifiers
to which this use has access.rwobsolete DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.40.20.1.5 |
licensing OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.50 |
licenseKeyTable SEQUENCE OF LicenseKeyEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10 |
licenseKeyEntry LicenseKeyEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10.1 |
licenseKeyIndexOrdinal inde for this table.
Identifies a license key database entry.
Each key may enable multiple features. A
list of features enabled by each key can be
found in the licenseFeatureTable.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10.1.1 |
licenseKeyRowStatusControls creation/deletion of rows in the
license key database.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10.1.2 |
keyThe license key string.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10.1.3 |
licenseKeyDurationIs this license key permanent or transient?
Permanent keys have no expiration date, transient
keys expire at the time found in the licenseKeyExpirationDate
object.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10.1.4 |
licenseKeyExpirationDateExact date and time when this license
key expires. Has no meaning if license
key is permanent.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10.1.5 |
licenseKeyAppliedDateDate and time when the license key
was applied. This field indicates the
chronological order in which the keys
were applied. If multiple keys enable
the same feature, the most recent key
supercedes older keys.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.50.10.1.6 |
licenseFeatureTableThis table is a list of all features
activated by a particular license key. SEQUENCE OF LicenseFeatureEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.50.20 |
licenseFeatureEntry LicenseFeatureEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.50.20.1 |
licenseFeatureIndexFeature index for this table, as well as
licensable feature table. If a feature is
not licensed, the row corresponding to that
feature does not appear here, but it does
appear in the licensableFeatureTable, as do
all licensableFeatures.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.50.20.1.1 |
featureNameName of the ADIC licensed feature enable
by this row's license key. The key is
specified by the value of licenseKeyIndex.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.50.20.1.2 |
licenseFeatureQuantityThe quantity of this licensed feature
enabled by this license key, if applicable.
For example, a license key which enables 1000 slots
of Capacity-on-Demand storage would have
quantity = 1000. For features which are not
licensed by quantity, return 0.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.50.20.1.3 |
licensableFeatureTableThis table is a list of all licensable features.
It defines the mapping between a feature name
and its licenseFeatureIndex. SEQUENCE OF LicensableFeatureEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.50.30 |
licensableFeatureEntry LicensableFeatureEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.50.30.1 |
licensableFeatureNameName of the ADIC licensable feature to be
displayed to the user.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.50.30.1.1 |
totalQuantityLicensedThe total licensed quantity for this feature.
For features which are licensed by quantity,
this object returns the sum of the indiviual
quantities enabled by each license key (see
licenseFeatureQuantity). For example, if
there were two COD license keys installed, one
for 500 slots and one for 1000 slots,
totalQuantityLicensed would return 1500.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.50.30.1.2 |
eventManager OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.70 |
registrationTable SEQUENCE OF RegistrationEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.70.10 |
registrationEntry RegistrationEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.70.10.1 |
hostIpAddressHost IP address to which SNMP traps will be
sent/forwarded.rw IpAddress .1.3.6.1.4.1.2.6.159.201.5.4.20.70.10.1.1 |
udpPortUDP Port number on which to send/forward
SNMP traps.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.70.10.1.2 |
registrationRowStatusControls creation/deletion of rows in the
notification (trap registration) table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.70.10.1.3 |
logTable** This table is optional **
Management functionality for general
event logging. Log entries are not
necessarily available via SNMP. SEQUENCE OF LogEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.70.20 |
logEntry** This entry object is optional ** LogEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.70.20.1 |
logName** This object is optional. **
Name of the log to be accessed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.70.20.1.1 |
logSnapshotTable** This table is optional. **
Management functionality for generating
a snapshot archive containing all of the
system logs SEQUENCE OF LogSnapshotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.70.30 |
logSnapshotEntry** This entry object is optional. ** LogSnapshotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.70.30.1 |
logSnapshotCommand** This object is optional. **
Commands are:
**********************
retrieveLogs - Gather snapshots of various
system logs in preparation to
build snapshot archive file.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.70.30.1.1 |
physicalLibrary OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.80 |
phGeneralInfoTable SEQUENCE OF PhGeneralInfoEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10 |
phGeneralInfoEntry PhGeneralInfoEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1 |
numElementDomainsNumber of element domains (such as DLT, LTO, 8mm, etc.)
currently installed in this physical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.1 |
numPhSlotsro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.2 |
numPhIESlotsro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.3 |
numPhDrivesro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.4 |
onlineStatusrw AdicOnlineStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.5 |
readinessro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.6 |
autoInventoryModerw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.7 |
autoCalibrateModerw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.8 |
autoConfigureModerw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.9 |
numPhAislesNumber of aisles in this library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.10 |
operatingModeControls library behavior when retrieving
tape from drives.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.11 |
numStorageCartridgesTotal number of storage cartridges present
in the libraryro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.12 |
numCleaningCartridgesTotal number of cleaning cartridges present
in the libraryro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.13 |
physLibraryManagerLunThe SCSI logical unit number of the
Physical Library Manager.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.14 |
physLibraryAutoCleaningEnable/disable automatic drive cleaning for
the entire physical library.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.15 |
physLibraryDoorStatusState of the library door:
(open/closed,locked/unlocked).ro AdicDoorStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.16 |
numPhFramesThe number of physical frames in
the library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.17 |
totalRawCapacityAn estimate of the amount of data which the
library can hold. Units are gigabytes. May
be computed by multiplying the number of cells
by the maximum number of gigabytes per tape.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.18 |
totalFreeCapacityAn estimate of the unused data capacity of the
library. Units are gigabytes. May be computed
by multiplying the number of empty cells
by the maximum number of gigabytes per tape.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.19 |
totalUsedCapacityAn estimate of the used data capacity of the
library. Units are gigabytes. May be computed
by multiplying the number of full cells
by the maximum number of gigabytes per tape.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.20 |
logicalSNAdressingModeEnables/disables the logical serial number
addressing feature.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.80.10.1.21 |
mediaDomainTableTable of all media domains installed in
the library. SEQUENCE OF MediaDomainEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.20 |
mediaDomainEntry MediaDomainEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.20.1 |
mediaDomainIndexro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.20.1.1 |
mediaDomainNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.20.1.2 |
numStorageElementsTotal number of storage elements for this
media domain in this physical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.20.1.3 |
numIeElementsTotal number of import/export elements for this
media domain in this physical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.20.1.4 |
numCleaningSlotsReturns the number of storage slots reserved for
cleaning media of this domain. When set, the
value is the total number of slots to reserve
for cleaning media of this domain. The library
will reserve a set of storage segments such
that total number of storage slots is greater
than or equal to numCleaningSlots.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.20.1.5 |
mediaTypeTableTable of media types. SEQUENCE OF MediaTypeEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.30 |
mediaTypeEntry MediaTypeEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.30.1 |
mediaTypeIndexro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.30.1.1 |
mediaTypeNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.30.1.2 |
numDriveElementsNumber of drives for this media type.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.30.1.3 |
phFrameTable** This table is optional **
This is a list of all the frames in the library. SEQUENCE OF PhFrameEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.41 |
phFrameEntry** This entry object is optional ** PhFrameEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.41.1 |
phFrameType** This object is optional **
Physical type of frame. Only controlModule(6)
and expansionModule(7) values are actually
valid for the frame type.rw AdicComponentType .1.3.6.1.4.1.2.6.159.201.5.4.20.80.41.1.1 |
phFrameSerialNumber** This object is optional **
Serial number of this frame, if available.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.41.1.2 |
phFrameNumRacks** This object is optional **
Number of racks in this frame.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.41.1.3 |
phSegmentTableThis is a list of all the segments in the library. SEQUENCE OF PhSegmentEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55 |
phSegmentEntry PhSegmentEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1 |
phSegmentAisleAisle coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.1 |
phSegmentFrameFrame coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.2 |
phSegmentRackRack coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.3 |
phSegmentSectionSection coordinate for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.4 |
phSegmentColColumn coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.5 |
phSegmentStartingRowRow coordinate of the first element in this segment.
This is useful to divide a column into multiple
segments. For instance, a segment which contains
rows 1 - 10 would have phSegmentStartingRow = 1. A
segment which contains rows 11 - 20 in the same
column would have phSegmentStartingRow = 11.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.6 |
phSegmentSizeNumber of elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.7 |
phSegmentTypeThis segment's type (storage, drive, I/E, etc.).ro AdicSegmentType .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.8 |
phSegmentMediaDomainElement domain of this segment.
Points a row in the media domain table.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.9 |
phSegmentStatusStatus of this segment. May be installed,
not installed, or reserved for use by the
automatic cleaning service.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.10 |
phSegmentCodStatusCapacity on Demand (COD) status for this
segment. noCod means that COD is not
enabled for this library.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.11 |
phSegStartingAddressSCSI media changer element address of the first
row in this segment. Element addresses are
contiguous, so we can derive the address of
each row in the segment from the address of
the first row.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.55.1.12 |
phStorageSegTableThis is a list of all the storage segments in the library, indexed by
their media domain and segment Index. SEQUENCE OF PhStorageSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.60 |
phStorageSegEntry PhStorageSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.60.1 |
phStorageSegSizeNumber of elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.60.1.1 |
phIeSegTable** Some objects in this table are optional **
This is a list of all the I/E segments in the library, indexed by
their media domain and segment index. SEQUENCE OF PhIeSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.70 |
phIeSegEntry** Some objects in this entry are optional ** PhIeSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.70.1 |
phIeSegSizeNumber of elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.70.1.1 |
phIeSegReserve** This object is optional **
Mechanism to release and reserve this
I/E segment.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.70.1.2 |
phIeSegReservedBy** This object is optional **
Indicator of who reserved this I/E segment.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.70.1.3 |
phIeSegOnlineStatus** This object is optional **
Takes this I/E segment online/offline.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.70.1.4 |
phIeSegCommand** This object is optional **
Issue a command to this I/E station.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.70.1.5 |
phIeStationTableThis is a list of all the I/E stations in the library SEQUENCE OF PhIeStationEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.75 |
phIeStationEntry PhIeStationEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.75.1 |
phIeStationNumberIndex of I/E station within a frame.
If a frame has N I/E stations, the
range of phIeStationNumber is
1 through N.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.75.1.1 |
phIeStationDoorStatusIs the station door open/closed,
locked/unlocked ?ro AdicDoorStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.80.75.1.2 |
phIeStationREDIdRuntime Error Detection identifier for this
import/export station.ro AdicREDIdentifier .1.3.6.1.4.1.2.6.159.201.5.4.20.80.75.1.3 |
phDriveSegTableThis is a list of all the drive segments in the library, indexed by
their media domain, media type and segment index. SEQUENCE OF PhDriveSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.80 |
phDriveSegEntry PhDriveSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.80.1 |
phDriveSegSizeNumber of drive elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.80.1.1 |
phDriveSegMediaTypeExact media type of this segment.
With phSegmentMediaDomain, points a
row in the media type table.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.80.1.2 |
phDriveSegInterfaceTypeData interface type of this segment.ro AdicInterfaceType .1.3.6.1.4.1.2.6.159.201.5.4.20.80.80.1.3 |
phCleaningSegTable** This table is optional **
This is a list of all the storage segments in the library
which have been reserved for use by automatic cleaning services. SEQUENCE OF PhCleaningSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.85 |
phCleaningSegEntry** This entry object is optional ** PhCleaningSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.85.1 |
phCleaningSegSize** This object is optional **
Number of elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.85.1.1 |
phCleaningSegRowStatus** This object is optional **
Management application use this object to
to reserve segment for cleaning or release
the segment for use as storage.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.85.1.2 |
phStorageSlotTable** This table is optional ** SEQUENCE OF PhStorageSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.90 |
phStorageSlotEntry** This entry object is optional ** PhStorageSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.90.1 |
phStorageRow** This object is optional **
Row coordinate value for this storage slot.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.90.1.1 |
phStorageElementAddr** This object is optional **
SCSI Medium Changer Element Address for this storage slot.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.90.1.2 |
phIeSlotTable** This table is optional ** SEQUENCE OF PhIeSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.100 |
phIeSlotEntry** This entry object is optional ** PhIeSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.100.1 |
phIeRow** This object is optional **
Row coordinate value for this I/E slotro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.100.1.1 |
phIeElementAddr** This object is optional **
SCSI Medium Changer Element Address for this I/E slot.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.100.1.2 |
phIeMediaPresent** This object is optional **
Is a media cartridge present in this slot? Values are:
yes(1) - system is certain that a cartridge is present.
no(2) - system is certain that a cartridge is not present.
error(3) - an error ocurred while determining if media is
present.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.100.1.3 |
phIeMediaId** This object is optional **
Media ID bar code of cartridge in this I/E
slot, if present and available. Returns
zero length string if the bar code is not
available for any reason.ro AdicBarCode .1.3.6.1.4.1.2.6.159.201.5.4.20.80.100.1.4 |
phDriveTable SEQUENCE OF PhDriveEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110 |
phDriveEntry PhDriveEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1 |
phDriveRowRow coordinate value for this drive element.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.1 |
phDriveElementAddrSCSI Element Address for this drive element.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.2 |
phDriveScsiIdrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.3 |
phDriveScsiLunrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.4 |
phDriveWwnWorld Wide Node Name for this drive.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.5 |
phDriveVendorName of the vendor of this drive.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.6 |
phDriveProductProduct name of this drive.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.7 |
phDriveSerialNumberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.8 |
phDriveNeedsCleaningrw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.9 |
phDriveAutoCleaningAdd or remove this drive from automatic
cleaning list.rw Boolean .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.10 |
phDriveInterfaceTypeData interface type (SCSI, Fibre Channel, etc.).ro AdicInterfaceType .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.11 |
phDriveFcLoopIdLoop ID for Fibre Channel interface drives,
undefined for other interface type drives.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.12 |
phDriveFcLoopIdModeLoop ID Mode for Fibre Channel interface drives,
undefined for other interface type drives.
Controls negotiation of the port ID on the
Fibre Channel connection.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.13 |
phDriveFcHardIdPreferred port ID Mode for Fibre Channel
interface drives, undefined for other interface
type drives. Used only when port ID mode is
set to 'hard'.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.14 |
phDriveStatusro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.15 |
phDriveCommandPerform various operations on a drive:
***************************************
online(1) - bring drive online
offline(2) - take drive offline
reset(3) - perform a warm reset
powerOn(4) - perform power on
powerOff(5) - peform power off
powerCycle(6) - perform power cycle
driveBrickUpdate(7) - download firmware to the drive brickrw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.16 |
phDriveFcPortIdPort ID for fabric attached Fibre Channel drives,
undefined for other interface type drives.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.17 |
phDriveCompressionOnIs compression turned on for this drive?rw Boolean .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.18 |
phDriveWriteProtectedIs write protection turned on for this drive?rw Boolean .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.19 |
phDriveNumLoadsTotal number of loads for this drive. Count
is for the entire lifetime of the drive.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.20 |
phDriveNumCleansTotal number of cleaning operations peroformed
on this drive. Count is for the entire lifetime
of the drive.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.21 |
phDrivePowerStatusIs this drive powered on?ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.22 |
phDriveReadErrorsNumber of read errors for this drive. Count
is for the entire lifetime of the drive.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.23 |
phDriveWriteErrorsNumber of write errors for this drive. Count
is for the entire lifetime of the drive.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.24 |
phDriveMbytesReadNumber of megabytes of data read from this drive.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.25 |
phDriveMbytesWrittenNumber of megabytes of data written to this drive.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.26 |
phDriveFirmwareVersionFirmware version for this drive.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.27 |
phDriveREDIdRuntime Error Detection identifier for this
tape drive.ro AdicREDIdentifier .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.28 |
phDriveOnlineStatusReturns either online(1) or offline(2). The
shutdown(3) state is not applicable to this
object. To change the online state of the drive,
set the phDriveCommand object to online(1) or
offline(2).ro AdicOnlineStatus .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.29 |
phDriveErrorCodeBytesString of bytes which contains error
information about the drive. The
meaning of each byte is as follows:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
byte 0: drive seven segment display codero OCTET STRING ( SIZE( 1 ) ) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.30 |
phDriveRasStatusRAS status for this individual drive.ro AdicStatusGroupState .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.31 |
phDriveWwPortNameWorld Wide Port Name for this drive.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.110.1.32 |
phDriveStatHistoryTableThis table contains historical data on drive
operations. Each row in the table gives various
statistical data for a single drive over a one hour
period. The table is indexed such that phIndex = 0
is the current hour's data, phIndex = 1 is one hour
ago, phIndex = 2 is two hours ago, etc. SEQUENCE OF PhDriveStatHistoryEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.112 |
phDriveStatHistoryEntry PhDriveStatHistoryEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.112.1 |
phHourIndexIndex into the historical data. The integer value
is the number in the past the data the data was collected.
For example, phHourIndex = 0 means the current hour's
statistics, phHourIndex = 1 means one hour in the past,
phHourIndex = 2 means two hours in the past.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.112.1.1 |
phHourlyMBytesReadNumber of megabytes read by this drive during the
one hour period indicated by phHourIndex.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.112.1.2 |
phHourlyMBytesWrittenNumber of megabytes written by this drive during the
one hour period indicated by phHourIndex.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.112.1.3 |
phHourlyMountsNumber of mounts performed by this drive during the
one hour period indicated by phHourIndex.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.112.1.4 |
phDrivePorts OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116 |
fcDrivePortTableThis table contains objects pertaining to
Fibre Channel port settings on native Fibre
Channel drives. SEQUENCE OF FcDrivePortEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116.10 |
fcDrivePortEntryA row object describing a Fibre Channel
port. FcDrivePortEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116.10.1 |
fcPortPreferredSpeedPreferred transmitter speed. Except for
auto(1), the numerical value of this object
is equal to the port speed in megabits per
second.
*******************************************
auto(1) - speed is auto-negotiated with no
preferred speed
megabits1000(1000) - 1000 megabits per second
megabits2000(2000) - 2000 megabits per secondrw AdicFcPortSpeed .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116.10.1.1 |
fcPortNegotiatedSpeedActual transmitter speed as negotiated
on the FC network. The numerical value of
this object is equal to the port speed in
megabits per second. Although auto(1) is
defined in the AdicFcPortSpeed enumeration,
the fcPortNegotiatedSpeed should never return
this value.
*******************************************
auto(1) - This object should never auto(1)
megabits1000(1000) - 1000 megabits per second
megabits2000(2000) - 2000 megabits per secondro AdicFcPortSpeed .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116.10.1.2 |
fcPortPreferredTypePreferred port type, such as N_Port or NL_Port.
auto(1) means no preference, auto-negotiate.rw AdicFcPortType .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116.10.1.3 |
fcPortNegotiatedTypeActual port type as negotiated on the
FC network. Should never return auto(1).ro AdicFcPortType .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116.10.1.4 |
fcPortTypeQualifierIs this a public or private port?ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.116.10.1.5 |
phMediaTable SEQUENCE OF PhMediaEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120 |
phMediaEntry PhMediaEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1 |
phMediaBarCodero AdicBarCode .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.1 |
phMediaDomainro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.2 |
phMediaTypero INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.3 |
phMediaElementAddressElement address where this cartridge is physically
located.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.4 |
phMediaMountsNumber of times this cartridge has been mounted.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.5 |
phMediaReadErrorsNumber of errors when reading from this cartridge.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.6 |
phMediaWriteErrorsNumber of errors when writing to this cartridge.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.7 |
phMediaCapacityCapacity of this cartridge in megabytes. Returns
-1 if capacity is unknown.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.8 |
phMediaFreeSpaceAmount of free space on this cartridge in megabytes. Returns
-1 if free space is unknown.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.9 |
phMediaExportedHas this cartridge been exported from the library?ro Boolean .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.10 |
phMediaImportTimestampTimestamp when cartridge was imported.
Compatible with the SMIv2 DateAndTime
textual convention. Encode is as follows:
field octets contents range
-
1 1-2 year 0..65536
2 3 month 1..12
3 4 day 1..31
4 5 hour 0..23
5 6 minutes 0..59
6 7 seconds 0..60
(use 60 for leap-second)
7 8 deci-seconds 0..9
8 9 direction from UTC '+' / '-'
9 10 hours from UTC 0..11
10 11 minutes from UTC 0..59
For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be
displayed as:
1992-5-26,13:30:15.0,-4:0
Note that if only local time is known, then timezone
information (fields 8-10) is not present.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.11 |
phMediaExportTimestampTimestamp when cartridge was exported.
Compatible with the SMIv2 DateAndTime
textual convention. Encode is as follows:
field octets contents range
-
1 1-2 year 0..65536
2 3 month 1..12
3 4 day 1..31
4 5 hour 0..23
5 6 minutes 0..59
6 7 seconds 0..60
(use 60 for leap-second)
7 8 deci-seconds 0..9
8 9 direction from UTC '+' / '-'
9 10 hours from UTC 0..11
10 11 minutes from UTC 0..59
For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be
displayed as:
1992-5-26,13:30:15.0,-4:0
Note that if only local time is known, then timezone
information (fields 8-10) is not present.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.80.120.1.12 |
phTransportTable** This table is optional ** SEQUENCE OF PhTransportEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130 |
phTransportEntry** This entry object is optional ** PhTransportEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130.1 |
phTransportElementAddress** This object is optional **ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130.1.1 |
phTransportNumRecoveredGets** This object is optional **
Number of recovered get operations for this
transport element. The count is for the entire
lifetime of the library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130.1.2 |
phTransportNumRecoveredPuts** This object is optional **
Number of recovered put operations for this
transport element. The count is for the entire
lifetime of the library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130.1.3 |
phTransportNumRecoveredScans** This object is optional **
Number of recovered scan operations for this
transport element. The count is for the entire
lifetime of the library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130.1.4 |
phTransportNumPuts** This object is optional **
Number put operations for this transport
element. The count is for the entire
lifetime of the library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130.1.5 |
phTransportREDId** This object is optional **
Runtime Error Detection identifier for this
tape drive.ro AdicREDIdentifier .1.3.6.1.4.1.2.6.159.201.5.4.20.80.130.1.6 |
phTransportDomainTable** This table is optional ** SEQUENCE OF PhTransportDomainEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.132 |
phTransportDomainEntry** This entry object is optional ** PhTransportDomainEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.132.1 |
phTransportDomainIndex** This object is optional **ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.132.1.1 |
phCleaningMediaTable** This table is optional **
This is a combination of data about slots reserved for
automatic cleaning and the cleaning cartridges themselves.
Since the relationship between slots and cartridges is
one-to-one, we can combine these data. SEQUENCE OF PhCleaningMediaEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140 |
phCleaningMediaEntry** This entry object is optional ** PhCleaningMediaEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1 |
phCleaningMediaRow** This object is optional **ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.1 |
phCleaningMediaStatus** This object is optional **
Cleaning storage is allocated by segment; the value
of phCleaningMediaStatus indicates if the slot is
being used to store a cartridge or not.
allocated(1) means this slot is home to cartridge.
unallocated(2) means there is no cartridge associated with this slot.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.2 |
phCleaningMediaTypeIndex** This object is optional **
Exact media type of this cleaning cartridge.
Value points to a row in the Media Type table with
mediaTypeIndex = phCleaningMediaTypeIndex.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.3 |
phCleaningMediaVendorId** This object is optional **
Vendor of drives that this cleaning cartridge
is designed to clean. Value points to a row
in the Vendor table with
vendorIdIndex = phCleaningMediaVendorId.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.4 |
phCleaningMediaBarcode** This object is optional **
Barcode (if present).rw AdicBarCode .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.5 |
phCleaningMediaUseCount** This object is optional **
Use count. May be set to any value to accomodate
importing cartridges that have already been used.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.6 |
phCleaningMediaMaxUses** This object is optional **
Maximum number of uses for this cartidge.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.7 |
phCleaningMediaImportTimestamp** This object is optional **
Timestamp when this cartridge was imported.
Compatible with the SMIv2 DateAndTime
textual convention. Encode is as follows:
field octets contents range
-
1 1-2 year 0..65536
2 3 month 1..12
3 4 day 1..31
4 5 hour 0..23
5 6 minutes 0..59
6 7 seconds 0..60
(use 60 for leap-second)
7 8 deci-seconds 0..9
8 9 direction from UTC '+' / '-'
9 10 hours from UTC 0..11
10 11 minutes from UTC 0..59
For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be
displayed as:
1992-5-26,13:30:15.0,-4:0
Note that if only local time is known, then timezone
information (fields 8-10) is not present.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.80.140.1.8 |
logicalLibrary OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.90 |
loGeneralInfoTableGeneral information about the Logical Library Manager. SEQUENCE OF LoGeneralInfoEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.10 |
loGeneralInfoEntry LoGeneralInfoEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.10.1 |
maxLogicalLibrariesMaximum number of logical libraries. This includes
all media types.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.10.1.1 |
numLogicalLibrariesCurrent number of logical libraries configured.
This includes all media types.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.10.1.2 |
masterOnlineStatusrw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.10.1.3 |
numVendorIdsro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.10.1.4 |
autoPartitionTableVariables pertaining to library auto partitioning. SEQUENCE OF AutoPartitionEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.12 |
autoPartitionEntryAutopartitioning is based on the media domain, media
type, and drive data port interface type. AutoPartitionEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.12.1 |
numAutoPartitionNumber of partitions to create upon
automatic partitioning for a given
media domain, media type and interface
type.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.12.1.1 |
autoPartitionCommandPerform operation based on the media domain,
media type, and interface type:
autoPartition(1) - create the number of partitions
indicated by the numAutoPartition
object, with the library resouces
divided equally among the partitions.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.12.1.2 |
vendorIdTableTable of possible vendors. SEQUENCE OF VendorIdEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.15 |
vendorIdEntry VendorIdEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.15.1 |
vendorIdIndexro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.15.1.1 |
vendorNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.90.15.1.2 |
numProductIdsro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.15.1.3 |
productIdTableTable of possible product names and configuration
constraints. SEQUENCE OF ProductIdEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17 |
productIdEntry ProductIdEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1 |
productIdIndexro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.1 |
productIdNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.2 |
productDrivesMinrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.3 |
productDrivesMaxrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.4 |
productSlotsMinrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.5 |
productSlotsMaxrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.6 |
productIeMinrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.7 |
productIeMaxrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.17.1.8 |
logicalLibraryTable SEQUENCE OF LogicalLibraryEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20 |
logicalLibraryEntry LogicalLibraryEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1 |
logicalLibraryIndexIdentifies the Logical Library to be
managed.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.1 |
commandrw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.2 |
namerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.3 |
assignedLunAssigned LUN of this library's
(virtual) SCSI media changer. This
can only be changed through the
SANMgr proxy MIB device map table.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.4 |
vendorIdrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.5 |
productIdrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.6 |
mediaDomainPoints to entry in the Physical Library
MediaDomainTable.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.7 |
mediaTypePoints to entry in the Physical Library
MediaTypeTable.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.8 |
numSlotsrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.9 |
numIErw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.10 |
numDrivesrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.11 |
loStatusrw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.12 |
automaticCleaningEnables/Disables automatic cleaning for
drives this logical library.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.13 |
mediaTypeCheckingEnables/Disables media type checking for
this logical library.rw AdicEnable .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.14 |
serialNumberSerial Number of this logical library. Assigned by
MCB when logical library is created.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.15 |
loInterfaceTypeType of data interface for this logical library.rw AdicInterfaceType .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.16 |
loNumLibrariesFormerly used in auto partition operation.
Made obsolete by autoPartition table.rwobsolete INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.17 |
loLtoTapeTagsControls the inclusion of media type characters
in the media barcodes for this logical library.
For example, the LTO media type characters are
'L1' for LTO-1 and 'L2' for LTO-2. This object
applies to logical libraries of all media domains,
not just LTO (as the name suggests).rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.18 |
loMediaTypeCheckingPolicyAllows the user to specify special handling of
media type information in barcodes. Values are:
0 - media type checking disabled; media type as
derived from barcode is irrelevant.
911 - 'required'; barcode MUST be a valid ADIC
barcode, the correct media type may be
derived from the barcode using the ADIC
algorithm.
Other - 'override'; the media type may not
be derived from the barcode, use this value
instead. The value map is the same as the
mediaTypeIndex variable: the logical
library's mediaDomain variable specifies
the media domain and loMediaTypeCheckingPolicy
specifies the media type that will be
assumed for all media in this logical
library.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.20.1.19 |
loSegmentTableThis is a list of all the segments in the library. SEQUENCE OF LoSegmentEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25 |
loSegmentEntry LoSegmentEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1 |
loSegmentAisleAisle coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.1 |
loSegmentFrameFrame coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.2 |
loSegmentRackRack coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.3 |
loSegmentSectionSection coordinate for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.4 |
loSegmentColColumn coordinate value for this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.5 |
loSegmentStartingRowRow coordinate of the first element in this segment.
This is useful to divide a column into multiple
segments. For instance, a segment which contains
rows 1 - 10 would have loSegmentStartingRow = 1. A
segment which contains rows 11 - 20 in the same
column would have loSegmentStartingRow = 11.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.6 |
loSegmentSizeNumber of elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.7 |
loSegmentTypeType segment (storage, I/E, drive).ro AdicSegmentType .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.8 |
loSegmentMediaDomainMedia domain for this segment.
Points to a row in the media
domain table.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.9 |
loSegmentBelongsTologicalLibraryIndex to which this segment is
allocated. This object has no meaning for
an I/E segment since I/E segments may be shared.
For I/E segments, the list of logical libaraies
which share the segment may be found in the
loSegmentAssignmentTable.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.10 |
loSegmentCommandOperation to perform using objects in varbind list.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.11 |
loSegmentStatusIs this segment allocated to a logical library?ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.12 |
loSegmentStartingAddressLogical SCSI element address of the first
element (row) in this segment. Element
addresses are contiguous within a segment
and unique within a logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.25.1.13 |
loSegmentBelongsToTableThis is a list of the logical libraries to
which each segments belongs. Storage and
drive segments belong to a maximum of
one logical library, but I/E segments
may be shared among several logical libraries. SEQUENCE OF LoSegmentBelongsToEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.27 |
loSegmentBelongsToEntry LoSegmentBelongsToEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.27.1 |
loSegmentAssignedTologicalLibraryIndex to which this segment belongs.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.27.1.1 |
loStorageSegTableThis is a list of all the storage segments in the library, indexed by
a flat segment index loStorageSegIndex. SEQUENCE OF LoStorageSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.30 |
loStorageSegEntry LoStorageSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.30.1 |
loStorageSegSizeNumber of storage elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.30.1.1 |
loStorageSegStartingAddressLogical SCSI element address of the first element
(row) in this storage segment. Element
addresses are contiguous within a segment
and unique within a logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.30.1.2 |
loIeSegTableThis is a list of all the I/E segments in the logical library,
indexed by a flat segment index. SEQUENCE OF LoIeSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.40 |
loIeSegEntry LoIeSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.40.1 |
loIeSegSizeNumber of I/E elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.40.1.1 |
loIeSegReserveMechanism to release and reserve this
I/E segment.rw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.90.40.1.2 |
loIeSegReservedByIndex of logical library for which this
I/E segment has been reserved.rw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.40.1.3 |
loIeSegStartingAddressLogical SCSI element address of the first
element (row) in this I/E segment. Element
addresses are contiguous within a segment
and unique within a logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.40.1.4 |
loDriveSegTableThis is a list of all the drive segments in the library, indexed by
their media domain, media type and segment index. SEQUENCE OF LoDriveSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.50 |
loDriveSegEntry LoDriveSegEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.50.1 |
loDriveSegSizeNumber of elements in this segment.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.50.1.1 |
loDriveSegStartingAddressLogical SCSI element address of the first
element (row) in this drive segment. Element
addresses are contiguous within a segment
and unique within a logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.50.1.2 |
loDriveSegMediaTypeExact media type of this segment.
With loSegmentMediaDomain, points a
row in the media type table.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.50.1.3 |
loDriveSegInterfaceTypeData interface for this segment.ro AdicInterfaceType .1.3.6.1.4.1.2.6.159.201.5.4.20.90.50.1.4 |
loStorageSlotTable SEQUENCE OF LoStorageSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.60 |
loStorageSlotEntry LoStorageSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.60.1 |
loStorageRowRow coordinate value for this storage slot.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.60.1.1 |
loIeSlotTable SEQUENCE OF LoIeSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.70 |
loIeSlotEntry LoIeSlotEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.70.1 |
loIeRowRow coordinate value for this storage slot.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.70.1.1 |
loDriveTable SEQUENCE OF LoDriveEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.80 |
loDriveEntry LoDriveEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.80.1 |
loDriveRowRow coordinate value for where this drive
element is physically located.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.80.1.1 |
loStatisticsTable** This table is optional **
Table of statistics for each logical library.
Error counts, recovery counts, etc. . SEQUENCE OF LoStatisticsEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90 |
loStatisticsEntry** This entry object is optional ** LoStatisticsEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1 |
loNumRecoveredGets** This object is optional **
Number of recovered get operations for this
logical library. The count is for the entire
lifetime of the logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1.1 |
loNumRecoveredPuts** This object is optional **
Number of recovered putt operations for this
logical library. The count is for the entire
lifetime of the logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1.2 |
loNumRecoveredScans** This object is optional **
Number of recovered scan operations for this
logical library. The count is for the entire
lifetime of the logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1.3 |
loStatsNumPuts** This object is optional **
Number of put operations performed for this
logical library. The count is for the entire
lifetime of the logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1.4 |
loStatsNumPutRetries** This object is optional **
Number of retried put operations performed for this
logical library. The count is for the entire
lifetime of the logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1.5 |
loStatsNumGetRetries** This object is optional **
Number of retried get operations performed for this
logical library. The count is for the entire
lifetime of the logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1.6 |
loStatsNumScanRetries** This object is optional **
Number of retried scan operations performed for this
logical library. The count is for the entire
lifetime of the logical library.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.90.90.1.7 |
ras OBJECT IDENTIFIER .1.3.6.1.4.1.2.6.159.201.5.4.20.100 |
rasSystemStatusTableContains status information for various system
status groups. SEQUENCE OF RasSystemStatusEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10 |
rasSystemStatusEntryInformation for a particular system status group.
The componentId index refers to the MCB through
which the management application accesses the RAS
manager. The rasStatusGroupIndex specifies the
system status group for which the entry contains
information. RasSystemStatusEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1 |
rasStatusGroupIndexIdentifies the system status group for which
this row object contains information.ro AdicStatusGroup .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.1 |
rasStatusGroupStatusThe status (or condition) of this system status group.
Use of the 'indeterminate' state: 'indeterminate' is
primarily for use in the rasStatusGroupPreviousStatus
object, where there may not be any previous state
information.ro AdicStatusGroupState .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.2 |
rasStatusGroupPreviousStatusAfter a state change, this object gives the
previous state of the system status group.
If there is no previous state information
available, such as when resetting the system,
the previous state is 'indeterminate'.ro AdicStatusGroupState .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.3 |
rasStatusGroupTextSummaryA brief message describing the state of this
system status group. If the rasStatusGroupStatus
is other than 'good', this object should return
the reason why this is so.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.4 |
rasStatusGroupTotalTicketsThe total number of RAS tickets created
against this system status group.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.5 |
rasStatusGroupOpenTicketsThe number of RAS tickets currently open
against this system status group.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.6 |
rasStatusGroupActionsPendingThe number of actions pending
against this system status group.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.7 |
rasStatusGroupLastChangeTimestamp of the last time the status changed.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.100.10.1.8 |
rasTicketTableContains one row for each ticket in the
database. SEQUENCE OF RasTicketEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20 |
rasTicketEntryEach entry contains information for a
single RAS ticket. The componentId index
refers to the MCB through which the management
application accesses the RAS manager. The
rasTicketId specifies the ticket instance. RasTicketEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1 |
rasTicketIdUnique identifier for this ticket. The RAS
system defines the ticket ID as an unsigned
32 bit integer, so it is declared here as a
Guage32.ro Gauge .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.1 |
rasTicketRowStatusControls creation and deletion of rows
in this table. Creation of RAS tickets
via SNMP is currently not permitted, so
writing a value of createAndGo(4) or
createAndWait(5) does not create a new
row; it may return error indication.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.2 |
rasTicketStaterw AdicRasTicketState .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.3 |
rasTicketQualifierrw Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.4 |
rasTicketPriorityrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.5 |
rasTicketDescriptionrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.6 |
rasTicketStatusGroupSystem status group to which this ticket
belongs.ro AdicStatusGroup .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.7 |
rasTicketGroupStatusStatus determination that this ticket indicates
against its system status group.ro AdicStatusGroupState .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.8 |
rasTicketClosedByrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.9 |
rasTicketVerifiedByrw INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.10 |
rasTicketCommentsrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.11 |
rasTicketSerialNumberro AdicFruSerialNumber .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.12 |
rasTicketTimeOpenedDate and time when ticket was opened.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.13 |
rasTicketTimeClosedDate and time when ticket was closed.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.14 |
rasTicketCountNumber of times an attempt was made to open
a duplicate ticket.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.15 |
rasTicketKeyReportContains 0 or a valid rasReportId value.
Indicates which report is currently responsible
for the severity of the ticket.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.20.1.16 |
rasReportTableContains one row for each ticket/report
combination in the database. The table
is indexed off the RAS Ticket Table, it
may contain many RAS Report entries for
a single RAS Ticket. SEQUENCE OF RasReportEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30 |
rasReportEntryEach entry contains information for a
single RAS Report. RasReportEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1 |
rasReportIdIdentifies the RAS Report for which this
this row object contains information. The RAS
system defines the report ID as an unsigned
32 bit integer, so it is declared here as a
Guage32.ro Gauge .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.1 |
rasReportRowStatusControls creation and deletion of rows
in the RAS Report table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.2 |
rasReportTimestampTime when this event was generated.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.3 |
rasReportStatusGroupThe subsystem that is reporting
the event.rw AdicStatusGroup .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.4 |
rasReportOrcDataEvent payload generated by the reporting
subsystem.rw OCTET STRING ( SIZE( 16 ) ) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.5 |
rasReportGroupStatusStatus determination that this report indicates
against the specific FRU.rw AdicStatusGroupState .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.6 |
rasReportDescriptionrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.7 |
rasReportOrcDescriptionDescription of the operation result code.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.8 |
rasReportRepeatCounterNumber of times an identical report has been
generated.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.9 |
rasReportSerialNumberro AdicFruSerialNumber .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.10 |
rasReportHeadReportThe head report field allows reports
to be sorted according to FRU branch.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.30.1.11 |
rasFruStatTableEach row dsecribes the history and RAS
statistics for a single FRU. SEQUENCE OF RasFruStatEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50 |
rasFruStatEntryEach entry contains information for a
single FRU. RasFruStatEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1 |
rasFruStatIndexFlat index for the FRU statistics table.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.1 |
rasFruInstanceIdUniquely identifies the FRU instance.ro Gauge .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.2 |
rasFruStatStatusGroupStatus group to which this FRU belongs.ro AdicStatusGroup .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.3 |
rasFruStatFruCategoryCategory to which this FRU belongs.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.4 |
rasFruStatFruIdFRU identifier.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.5 |
rasFruStatFirstReportTimeTime when the first RAS report was generated
for this FRU.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.6 |
rasFruStatLastReportTimeTime when the most recent RAS report was generated
for this FRU.ro AdicDateAndTime .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.7 |
rasFruStatTotalTicketsTotal number of RAS tickets created against
this FRU, both open and closed tickets.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.8 |
rasFruStatOpenTicketsNumber of RAS tickets currently open
against this FRU.ro INTEGER .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.9 |
rasFruStatSerialNumberThe unique serial number of the FRU.ro AdicFruSerialNumber .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.10 |
rasFruStatStateState = current(1) indicates that
the FRU is currently installed.
State = old(2) indicates that the
FRU has been removed and the data
is historic.ro Enumeration .1.3.6.1.4.1.2.6.159.201.5.4.20.100.50.1.11 |
rasTicketFilterTableContains filter settings for ticket table
walking. Only those rows which match the
filter criteria will appear in the RAS
ticket table when traversed using GetNext
or GetBulk. SEQUENCE OF RasTicketFilterEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.60 |
rasTicketFilterEntry RasTicketFilterEntry .1.3.6.1.4.1.2.6.159.201.5.4.20.100.60.1 |
rasTicketFilterStatusGroupIdentifies the system status group for which
tickets will be returned.rw AdicStatusGroup .1.3.6.1.4.1.2.6.159.201.5.4.20.100.60.1.1 |
rasTicketFilterStateIdentifies the ticket state (open, closed, etc.) for which
tickets will be returned.rw AdicRasTicketState .1.3.6.1.4.1.2.6.159.201.5.4.20.100.60.1.2 |
rasTicketFilterSeverityIdentifies the ticket severity for which
tickets will be returned.
=========================================
high: Tickets/reports with status 'failed' only.
medium: Tickets/reports with status 'failed' or 'warning'.
low: All tickets/reports.rw AdicRasTicketSeverity .1.3.6.1.4.1.2.6.159.201.5.4.20.100.60.1.3 |