ACE20-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ACE20-MIB.
263
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
263 total| Object Name |
|---|
radAtmEventsThe events for RAD ATM. OBJECT IDENTIFIER .radAtm.0 |
alarmTrapThis trap is sent whenever an alarm
occurs in the agent. NOTIFICATION-TYPE .radAtm.0.1 |
statusChangeTrapThis trap is sent whenever a led in the agent
change it's status. NOTIFICATION-TYPE .radAtm.0.2 |
atmSuAgnNoBufferToNetworkThis trap usualy indicates timing problem;
incorrect selection of timing references
between end users. NOTIFICATION-TYPE .radAtm.0.3 |
atmSuJitterBufferOverrunThis trap indicates that an overrun event
occurred in the ATM jitter buffer serving the
transmit to user direction of the
user interface specified by ifAlias NOTIFICATION-TYPE .radAtm.0.4 |
atmSuJitterBufferUnderrunThis trap indicates that an underrun event
occurred in the atm jitter buffer serving the
transmit to user direction of the
user interface specified by ifAlias. NOTIFICATION-TYPE .radAtm.0.5 |
atmSuDataLocalLoopbackTrapThis trap indicates that a local loopback
has been activated on the local data port. NOTIFICATION-TYPE .radAtm.0.6 |
atmSuDataRemoteLoopbackTrapThis trap indicates that a remote loopback
has been activated on the local data port. NOTIFICATION-TYPE .radAtm.0.7 |
atmSu OBJECT IDENTIFIER .radAtm.4 |
IF-MIB Unknown .radAtm.4 |
RFC1155-SMI NOTIFICATION-TYPE .radAtm.4 |
atmSuSystem OBJECT IDENTIFIER .radAtm.4.1 |
atmSuSystemSwOperStatusThis value indicates if tftp-write operation (for downloading
software from an external host) is allowed by the agent.rw Enumeration .radAtm.4.1.1 |
atmSuSystemSwSwitchVersionsCmdThis command is used to switch beetween software versions stored
in the flash. setting this value to active will reset the agent
and re-activate it with the new version ( only if new version is valid).
on get-request this value will be always notActive.rw Enumeration .radAtm.4.1.2 |
atmSuSystemHistoryAlrTablebuffer contain history buffer of agent alarms. SEQUENCE OF AtmSuSystemHistoryAlrEntry .radAtm.4.1.3 |
atmSuSystemHistoryAlrEntryAgent alarm history list entry. AtmSuSystemHistoryAlrEntry .radAtm.4.1.3.1 |
atmSuSystemHistoryAlrIndexA unique number to identify an entry in the history alarm table.ro Integer32 .radAtm.4.1.3.1.1 |
atmSuSystemHistoryAlrIfIndexThis value indicates the port on which the alarms occured.
configuration(system) alarms have port index equal to 0.ro Integer32 .radAtm.4.1.3.1.2 |
atmSuSystemHistoryAlrDescriptionThis attribute is a text description of the alarm.
The alarm descipion include alarm code and alarm text.ro DisplayString .radAtm.4.1.3.1.3 |
atmSuSystemHistoryAlrStatusThis attribute indicates the status of the alarm.ro Enumeration .radAtm.4.1.3.1.4 |
atmSuSystemHistoryAlrOccurrenceTimeThis value indicates the date and time of the occurrence
of the event that caused this alarm.
Date and time format: YYYY-MM-DD, HH:MM:SSro DisplayString (SNMPv2-TC) .radAtm.4.1.3.1.5 |
atmSuSystemHistoryAlrVpiThis value indicates the ATM VPI of the connection
associated with the event that caused this alarm.
When not applicable, value is 0ro Integer32 .radAtm.4.1.3.1.6 |
atmSuSystemHistoryAlrVciThis value indicates the ATM VCI of the connection
associated with with the event that caused this alarm.
When not applicable, value is 0ro Integer32 .radAtm.4.1.3.1.7 |
atmSuSystemClearHistoryAlrListCmdSetting this attribute to ON, enforce a clear operation on
the agent history event buffer .
On reading, attribute will always get status 'off' .rw Enumeration .radAtm.4.1.4 |
atmSuSystemCurrentAlrTabletable which contains all alarms Currently active ( status ON )
in the agent. SEQUENCE OF AtmSuSystemCurrentAlrEntry .radAtm.4.1.5 |
atmSuSystemCurrentAlrEntryAgent alarm list entry. AtmSuSystemCurrentAlrEntry .radAtm.4.1.5.1 |
atmSuSystemCurrentAlrIndexA unique number to identify an entry in the Current alarms table.ro Integer32 .radAtm.4.1.5.1.1 |
atmSuSystemCurrentAlrIfIndexThis value indicates the port on which the alarms occured.
configuration alarms have port index equal to 0.ro Integer32 .radAtm.4.1.5.1.2 |
atmSuSystemCurrentAlrDescriptionThis attribute is a text description of the alarm.
The alarm descipion include alarm code and alarm text.ro DisplayString .radAtm.4.1.5.1.3 |
atmSuSystemILMICommunityCommunity string for ILMI requests. 10 chars.rw DisplayString (SNMPv2-TC) .radAtm.4.1.6 |
atmSuSystemTrapMaxManagersThe maximum number of managers that can be registered
for receiving traps and sending requests.ro Integer32 .radAtm.4.1.7 |
atmSuSystemAalSelectionSelect ATM adaptation layers AAL1 or AAL2
Applicable for LA-140rw Enumeration .radAtm.4.1.8 |
atmSuSystemCodingLawThis attribute indicates the Method/Law for decoding/encoding the voice
information.
aLaw (2) is the standard Law for E1 links.
uLaw (3) is the standard Law for T1 links.
Coding law is applicable for all the ports in the systemrw Enumeration .radAtm.4.1.9 |
atmSuSystemISDNDataLinkActivationThis attribute indicates data link aactivation for all
ISDN ports in the system.
nonPermanent (2) = non permanent data link activation
permanent (3) = permanent data link activationrw Enumeration .radAtm.4.1.10 |
atmSuSystemJitterBufferThe field is set in ms and sets the jitter buffer size.
The jitter buffer adapts the size of the LA140 traffic
to the cdv (cell delay variation) of the ATM network.rw Integer32 .radAtm.4.1.11 |
atmSuSystemOperModeThe field indicates device mode of operation:
ima (2) = Inverse Multiplex ATM - ATM traffic is
distributed between links in IMA group.
miniDSLAM (3) => each link serves as separate
ATM interface.ro Enumeration .radAtm.4.1.12 |
atmSuSystemDSPGainThis object indicates DSP Gain.
Range of possible values is -12....12.
For LA-110 suset of this range is supported.rw Integer32 .radAtm.4.1.13 |
atmSuPort OBJECT IDENTIFIER .radAtm.4.2 |
atmSuPortDataCnfgTableData Port global configuration table.
this table include parametes which are common to the physical port
and not depend on whether the port interface is Frame-Relay or
ATM-DXI. SEQUENCE OF AtmSuPortDataCnfgEntry .radAtm.4.2.1 |
atmSuPortDataCnfgEntrythe entries at this table describes the configuration
of the Data-Port. AtmSuPortDataCnfgEntry .radAtm.4.2.1.1 |
atmSuPortDataApplicationThis attribute indicates the protocol application which runs
above the physical port.rw Enumeration .radAtm.4.2.1.1.1 |
atmSuPortDataRateThis attribute indicates the operation rate of the port.
AmcdT1 / Ace-20T allowes rates up to 1536KBps ( options 1-12 ),
while AmcdE1 / Ace-20E allowes all options.rw Enumeration .radAtm.4.2.1.1.2 |
atmSuPortDataDCDThis attribute define behavior of control signals DCD and RTS
These signals may obey or ignore signal from remote device.
The terms 'I signal' and 'C signal' are used
when physical data interface is X.21 ;
RTS = C signal, DCD = I signalrw Enumeration .radAtm.4.2.1.1.3 |
atmSuPortDataModeThis attribute indicates the port mode of sampling data physical.rodeprecated Enumeration .radAtm.4.2.1.1.4 |
atmSuPortDataCRCThis attribute indicates the type of CRC checking
on receiving/transmiting frames.rw Enumeration .radAtm.4.2.1.1.5 |
atmSuPortDataClockThis attribute indicates the clock using for synchronization
for the data port.rw Enumeration .radAtm.4.2.1.1.6 |
atmSuPortDataMaxNoOfConnsthis object indicates the maximum number of cross-connect
connections allowed beetween the ATM port and the Data Port
identified by IfIndex.ro Integer32 .radAtm.4.2.1.1.7 |
atmSuPortDataConfNoOfConnsthis object indicates the configured number of cross-connect
connections exist beetween the ATM port and the Data Port
identified by IfIndex.ro Integer32 .radAtm.4.2.1.1.8 |
atmSuPortDataIdleCodeThis attribute is applicable only for application aal1Stream.
It indicates the value to be transmitted whenever the port is idle.rw Integer32 .radAtm.4.2.1.1.9 |
atmSuPortDataInterfaceTypeConfigureable physical layer interface typerw Enumeration .radAtm.4.2.1.1.10 |
atmSuPortDataClkPolarityThis object indicates the clock polarity.
For LA-110/140 this object will be applicable only for
X.21/V.35/data portrw Enumeration .radAtm.4.2.1.1.11 |
atmSuPortDataCtsStatusCTS status - the signal state received from ATM network
(for the local DTE usage).
LA110 receiving RTS down from remote DTE device
via ATM network, will change CTS signal state
to down (off) toward local DTE devicero Enumeration .radAtm.4.2.1.1.12 |
atmSuPortDataRtsStatusRTS status - the signal state received from local DTE
(to be forwarded to ATM network).
LA110 receiving RTS down from the local DTE device
will transmit all '1' to ATM (in order to carry the
signaling to remote LA110), and forward it (RTS-down)
to far end through ATM cell (pointer field).ro Enumeration .radAtm.4.2.1.1.13 |
atmSuPortDs1 OBJECT IDENTIFIER .radAtm.4.2.2 |
atmSuPortDs1CnfgTableThis table include expansion configuration to the DS1 physical port. SEQUENCE OF AtmSuPortDs1CnfgEntry .radAtm.4.2.2.1 |
atmSuPortDs1CnfgEntrythe entries at this table describes the configuration
of the agent physical. AtmSuPortDs1CnfgEntry .radAtm.4.2.2.1.1 |
atmSuPortDs1CnfgRxSensitivityThis attribute is the rx line sensetivity parameter used only for
T1/CSU and E1/LTU interfaces.rw Enumeration .radAtm.4.2.2.1.1.1 |
atmSuPortDs1CnfgLBOThis attribute is the line-Build-Out indicates sensitivity of the DS1 interface.
The user can define if the agent will be CSU or DSU (for T1 only) by choosing the
right option.
On E1 interface this is done by hardware, so this parameter cannot be written.rw Enumeration .radAtm.4.2.2.1.1.2 |
atmSuPortDs1CnfgRestoreTimeDetermines the time passing from the disappearance of the loss of
synchronization condition (red alarm) to the restoration of normal
service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces
are proprietary implementation of the T1 standard to the E1 interface.rw Enumeration .radAtm.4.2.2.1.1.3 |
atmSuPortDs1CnfgInbandMngA unique number to identify type of
inband management over the link.
For LA-104 and IMXi4, only one port may be used
for inband managementrw Enumeration .radAtm.4.2.2.1.1.4 |
atmSuPortDs1CnfgDedicatedTsA unique number to identify Dedicated Time Slot for inband management
of the T1/E1 port.
It is applicable only when atmSuPortDs1CnfgInbandMng
selected is not off.
1..24 - Dedicated TS of T1
1..31 - Dedicated TS of E1
255 - notApplicable (for agents that do not support this
feature)
Other values are invalid.rw Integer32 .radAtm.4.2.2.1.1.5 |
atmSuPortDs1CbrCnfgTableThis table include expansion configuration to the DS1 physical port. SEQUENCE OF AtmSuPortDs1CbrCnfgEntry .radAtm.4.2.2.2 |
atmSuPortDs1CbrCnfgEntrythe entries at this table describes the configuration
of the agent physical. AtmSuPortDs1CbrCnfgEntry .radAtm.4.2.2.2.1 |
atmSuPortDs1CbrIdleCodeAn Idle code which sent on unused time-slots at CBR port .rw Integer32 .radAtm.4.2.2.2.1.1 |
atmSuPortDs1CbrRxTimeSlotsThis value indicates the time-slots used by the port for receiving.
It uses 32 bits ( in 4 bytes octet string ) for E1 and low 24 bits for T1.
each bit represents a time slot for receiving :
time-slot 0 = bit 0 (LSB - most right bit in last byte),
...
...
time-slot 31 = bit 31 (MSB - most left bit in first byte ).
value '0' indicate unused time-slot and value '1' indicates used time-slot.
note : time-slots '0' and '16' are used for signalling in E1 interface.ro TimeSlots .radAtm.4.2.2.2.1.2 |
atmSuPortDs1CbrTxTimeSlotsThis value indicates the time-slots used by the port for transmiting.
It uses 32 bits for E1 and low 24 bits for T1.
each bit represents a time slot for transmiting :
time-slot 0 = bit 0 (LSB - most right bit in last byte),
...
...
time-slot 31 = bit 31 (MSB - most left bit in first byte ).
value '0' indicate unused time-slot and value '1' indicates used time-slot.
note : time-slots '0' and '16' are used for signalling in E1 interface.ro TimeSlots .radAtm.4.2.2.2.1.3 |
atmSuPortDs1CbrMaxNoOfConnsthis object indicates the maximum number of cross-connect
connections allowed beetween the ATM port and the CBR Port
identified by IfIndex.ro Integer32 .radAtm.4.2.2.2.1.4 |
atmSuPortDs1CbrConfNoOfConnsthis object indicates the configured number of cross-connect
connections exist beetween the ATM port and the CBR Port
identified by IfIndex.ro Integer32 .radAtm.4.2.2.2.1.5 |
atmSuPortDs1CbrSignallingSampleTimedetermines how often the signalling of the DBCES connections are sampled
and thier activity determined.rw Enumeration .radAtm.4.2.2.2.1.6 |
atmSuPortAtm OBJECT IDENTIFIER .radAtm.4.2.3 |
atmSuPortAtmCnfgTableThis table contains global configuration to the ATM port. SEQUENCE OF AtmSuPortAtmCnfgEntry .radAtm.4.2.3.1 |
atmSuPortAtmCnfgEntryThis object contains information about agent ATM configuration. AtmSuPortAtmCnfgEntry .radAtm.4.2.3.1.1 |
atmSuPortAtmCnfgIdleCellCLPDetermines the clp bit value for transmition
in empty time slots.rw Enumeration .radAtm.4.2.3.1.1.1 |
atmSuPortAtmCnfgScrambleDetermined by the standards if the cell will be scrambled or not.rw Enumeration .radAtm.4.2.3.1.1.2 |
atmSuPortAtmSNMPVpiThe Vcc Vpi for SNMP requests.rw Integer32 .radAtm.4.2.3.1.1.3 |
atmSuPortAtmSNMPVciThe Vcc Vci for SNMP requests.rw Integer32 .radAtm.4.2.3.1.1.4 |
atmSuPortAtmSNMPStatusvalue indicates if the SNMP Vcc is available for management.rw Enumeration .radAtm.4.2.3.1.1.5 |
atmSuPortAtmILMIStatusValue indicates if agent should respond to ILMI requests from the
Atm switch or forward it.
note: when using Atm to Frame-Relay configuration this value should be
active to support ILMI.
when using Atm-AtmDxi configuration the ILMI requests should be
moved forward to the DTE or may be answered by the DCE.rw Enumeration .radAtm.4.2.3.1.1.6 |
atmSuPortAtmSNMPIpThe interface IP address for SNMP requests.rw IpAddress .radAtm.4.2.3.1.1.7 |
atmSuPortAtmCnfgCDVOptimizationvalue indicates if optimization of CDV (Cell Delay Varation)
is enbabled.rw Enumeration .radAtm.4.2.3.1.1.8 |
atmSuPortAtmCnfgShapingModeATM Shaping mode.
Three possible values:
SW Shaping.
HW Shaping - APC with NCITS = 1.
HW Shaping - APC with NCITS = 2
The difference between the two hardware modes
is in the connection cell granularity
and maximum bandwidth (BW):
* For NCITS=1, the granularity is of one cell
and the max. BW is the uplink BW,
* For NCITS=2, the granularity is of every two cells
and the max. BW is half of the uplink BW.rw Enumeration .radAtm.4.2.3.1.1.9 |
atmSuPortAtmSNMPTrafficDescrIndexThe value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.rw AtmTrafficDescrParamIndex .radAtm.4.2.3.1.1.10 |
atmSuPortAtmIfStatsTableThe table contains additional statistics information about
the ATM interface. SEQUENCE OF AtmSuPortAtmIfStatsEntry .radAtm.4.2.3.2 |
atmSuPortAtmIfStatsEntryAn entry in the ATM Interface statistics table. AtmSuPortAtmIfStatsEntry .radAtm.4.2.3.2.1 |
atmSuPortAtmRxClp0CellsThe number of cells received with correct
HECs and CLP=0 and not misroutedro Counter32 .radAtm.4.2.3.2.1.1 |
atmSuPortAtmRxClp1CellsThe number of cells received with correct
HEC's and CLP=1 and not misrouted.ro Counter32 .radAtm.4.2.3.2.1.2 |
atmSuPortAtmRxEfciSetCellsThe number of cells received with EFCI bit set by
the Agentro Counter32 .radAtm.4.2.3.2.1.3 |
atmSuPortAtmRxOamCellsThe number of OAM cells received with correct HECs.ro Counter32 .radAtm.4.2.3.2.1.4 |
atmSuPortAtmTxClp0CellsThe number of cells transmitted with CLP=0.ro Counter32 .radAtm.4.2.3.2.1.5 |
atmSuPortAtmTxClp1CellsThe number of cells transmitted with CLP=1.ro Counter32 .radAtm.4.2.3.2.1.6 |
atmSuPortAtmTxEfciSetCellsThe number of cells transmitted with EFCI bit set by
the Agentro Counter32 .radAtm.4.2.3.2.1.7 |
atmSuPortAtmTxOamCellsThe number of transmitted OAM cells.ro Counter32 .radAtm.4.2.3.2.1.8 |
atmSuPortAtmVclStatsTableThe table contains additional information about
the ATM Vcl end points. SEQUENCE OF AtmSuPortAtmVclStatsEntry .radAtm.4.2.3.3 |
atmSuPortAtmVclStatsEntryAn entry in the ATM Vcl statistics table. AtmSuPortAtmVclStatsEntry .radAtm.4.2.3.3.1 |
atmSuPortAtmVclStatsRxCellsThe total number of cells received with
correct HEC's.ro Counter32 .radAtm.4.2.3.3.1.1 |
atmSuPortAtmVclStatsRxClp0CellsThe number of cells received with correct
HEC's and CLP=0.ro Counter32 .radAtm.4.2.3.3.1.2 |
atmSuPortAtmVclStatsRxClp1CellsThe number of cells received with correct
HEC's and CLP=1.ro Counter32 .radAtm.4.2.3.3.1.3 |
atmSuPortAtmVclStatsRxDiscardsCellsThe number of cells, in ingress direction,
discarded due to policing violation.ro Counter32 .radAtm.4.2.3.3.1.4 |
atmSuPortAtmVclStatsTxCellsThe total number of cells transmitted.ro Counter32 .radAtm.4.2.3.3.1.5 |
atmSuPortAtmVclStatsTxClp0CellsThe number of cells transmitted with CLP=0.ro Counter32 .radAtm.4.2.3.3.1.6 |
atmSuPortAtmVclStatsTxClp1CellsThe number of cells transmitted with CLP=1.ro Counter32 .radAtm.4.2.3.3.1.7 |
atmSuPortAtmVclStatsRxTotalAISCellsTotal number of AIS cells received on the VC.ro Counter32 .radAtm.4.2.3.3.1.8 |
atmSuPortAtmVclStatsRxTotalCCCellsTotal number of Continuity Check cells that were
received on the VC.ro Counter32 .radAtm.4.2.3.3.1.9 |
atmSuPortAtmVclStatsTotalSuccLoopbacksTotal number of loopbacks that were requested by the ACE20
and for which there was a response (not supported).ro Counter32 .radAtm.4.2.3.3.1.10 |
atmSuPortAtmVclStatsTotalFailLoopbacksTotal number of loopbacks that were requested by the ACE20
and for which there was no response (not supported).ro Counter32 .radAtm.4.2.3.3.1.11 |
atmSuPortAtmVclStatsRxTotalRDICellsTotal number of RDI cells received on a VC.ro Counter32 .radAtm.4.2.3.3.1.12 |
atmSuPortAtmVclStatsTotalLOCSecondsTotal number of seconds during which there was loss of
continuity on the VC - no data and no continuity check cells
were received on the VC whilst it was in 'sink' continuity
check mode.ro Counter32 .radAtm.4.2.3.3.1.13 |
atmSuPortAtmVclStatsRxTotalLoopbackRequestsTotal number of loopback requests received by the ACE20 on a VC.ro Counter32 .radAtm.4.2.3.3.1.14 |
atmSuPortAtmVclStatsTxTotalAISCellsTotal number of AIS cells that were transmitted on a VC.ro Counter32 .radAtm.4.2.3.3.1.15 |
atmSuPortAtmVclStatsTxTotalCCCellsTotal number of continuity check cells that were transmitted on
a VC (when there is no data cells and the connection is in
'source' continuity check mode).ro Counter32 .radAtm.4.2.3.3.1.16 |
atmSuPortAtmVclStatsTxTotalRDICellsTotal number of RDI cells transmitted on a VC.ro Counter32 .radAtm.4.2.3.3.1.17 |
atmSuPortAtmVclStatsTxTotalLoopbackResponsesTotal number of loopback responses that were transmitted as a
result of loopback requests received.ro Counter32 .radAtm.4.2.3.3.1.18 |
atmSuPortAtmVclStatsTxTotalLoopbackRequestsTotal number of loopback requests that were transmitted by the ACE20 on a VC.ro Counter32 .radAtm.4.2.3.3.1.19 |
atmSuPortAtmVclStatsRxTotalLoopbackResponsesTotal number of loopback responses that were received as a
result of loopback transmitted by the ACE20.ro Counter32 .radAtm.4.2.3.3.1.20 |
atmSuPortFr OBJECT IDENTIFIER .radAtm.4.2.4 |
atmSuPortFrLportTableThe table Contains configuration parameters of the Frame-Relay
port and has expansion to frLportTable in RFC1604 MIB. SEQUENCE OF AtmSuPortFrLportEntry .radAtm.4.2.4.1 |
atmSuPortFrLportEntryAn entry in the Frame Relay Logical Port
Information table. AtmSuPortFrLportEntry .radAtm.4.2.4.1.1 |
atmSuPortFrLportSNMPDlciThe SNMP Dlci of this entry.rw Integer32 .radAtm.4.2.4.1.1.1 |
atmSuPortFrLportSNMPStatusvalue indicates if SNMP over FR is available for management.rw Enumeration .radAtm.4.2.4.1.1.2 |
atmSuPortFrLportVCSigProtocolThe value of this object identifies the Local
In-Channel Signaling Protocol that is used for
this frame relay UNI/NNI logical port.rw Enumeration .radAtm.4.2.4.1.1.3 |
atmSuPortFrLportVCSigProcedureThe value of this object identifies the Local
In-Channel Signaling Procedure that is used for
this UNI/NNI logical port. The UNI/NNI logical
port can be performing user-to-network
network-side and user-to-network user-side procedures
or bidirectional procedures.
this parameter gets value 'notApplicable when the VCSigProtocol is nonerw Enumeration .radAtm.4.2.4.1.1.4 |
atmSuPortFrLportCLLMindicate if the configuration is supporting CLLM ( Consolidated Link
Layer Management ) .rw Enumeration .radAtm.4.2.4.1.1.5 |
atmSuPortFrLportSNMPIpThe interface IP address of this entry.rw IpAddress .radAtm.4.2.4.1.1.6 |
atmSuPortFrPvcEndptTableThe table contains additional information about
the Frame Relay end point. SEQUENCE OF AtmSuPortFrPvcEndptEntry .radAtm.4.2.4.2 |
atmSuPortFrPvcEndptEntryAn entry for FR end-point statistics ( expansion to RFC 1604 ). AtmSuPortFrPvcEndptEntry .radAtm.4.2.4.2.1 |
atmSuPortFrPvcEndptTxFECNsnumber of frames transmited with FECN ( Forward Explicit
Congestion Notification ).ro Counter32 .radAtm.4.2.4.2.1.1 |
atmSuPortFrPvcEndptTxBECNsnumber of frames transmited with BECN ( Backward Explicit
Congestion Notification ).ro Counter32 .radAtm.4.2.4.2.1.2 |
atmSuPortFrPvcEndptTxDEsnumber of frames transmited with the DE ( Discarded Eligible ) bit set.ro Counter32 .radAtm.4.2.4.2.1.3 |
atmSuPortFrPvcEndptRxFECNsnumber of frames received with FECN ( Forward Explicit
Congestion Notification ).ro Counter32 .radAtm.4.2.4.2.1.4 |
atmSuPortFrPvcEndptRxBECNsnumber of frames received with BECN ( Backward Explicit
Congestion Notification ).ro Counter32 .radAtm.4.2.4.2.1.5 |
atmSuPortDxi OBJECT IDENTIFIER .radAtm.4.2.5 |
atmSuPortDxiConfTableThis table contains ATM-DXI managment
address (DFA) ending at the local agent.
only LMI managment supported for ATM-DXI. SEQUENCE OF AtmSuPortDxiConfEntry .radAtm.4.2.5.1 |
atmSuPortDxiConfEntryThis object contains information about agent Dxi interface. AtmSuPortDxiConfEntry .radAtm.4.2.5.1.1 |
atmSuPortDxiPortModeThis object identifies the dxi mode being used by
the atm dxi port.rw Enumeration .radAtm.4.2.5.1.1.1 |
atmSuPortDxiSigProtocolThis value indicates if we using LMI signalling protocol
or not using any signalling .rw Enumeration .radAtm.4.2.5.1.1.2 |
atmSuPortDxiSigDfaThe Signalling Dfa address .
the default LMI Dfa defined for LMI by the AtmForum is 0.rw Integer32 .radAtm.4.2.5.1.1.3 |
atmSuPortCmdTableGeneral commands to be done on agent's ports. SEQUENCE OF AtmSuPortCmdEntry .radAtm.4.2.6 |
atmSuPortCmdEntryThis object contains entry information. AtmSuPortCmdEntry .radAtm.4.2.6.1 |
atmSuResetPortStatsCmdreset statistics of port.rw Enumeration .radAtm.4.2.6.1.1 |
atmSuResetConnsStatsCmdreset statistics of all cross connections attached to this port.
set-request is allowed only on the DATA Ports .
for get-request value is always 'off'rw Enumeration .radAtm.4.2.6.1.2 |
atmSuPortEther OBJECT IDENTIFIER .radAtm.4.2.7 |
atmSuPortEtherTableThe table Contains configuration parameters of the Ethernet port. SEQUENCE OF AtmSuPortEtherEntry .radAtm.4.2.7.1 |
atmSuPortEtherEntryAn entry in the Ethernet Port Information table. AtmSuPortEtherEntry .radAtm.4.2.7.1.1 |
atmSuPortEtherIPThe interface IP address for SNMP requests.rw IpAddress .radAtm.4.2.7.1.1.1 |
atmSuPortEtherMaskThe interface IP address mask for SNMP requests.rw IpAddress .radAtm.4.2.7.1.1.2 |
atmSuPortEtherDefaultGateWayIpThe Ethernet bridge default gateway IP address.rw IpAddress .radAtm.4.2.7.1.1.3 |
atmSuPortEtherDefaultCrossConnectIdDefault Cross Connect Id.rw Integer32 .radAtm.4.2.7.1.1.4 |
atmSuPortEtherDefaultGatewayStatusDefault Gateway Status.rw Enumeration .radAtm.4.2.7.1.1.5 |
atmSuPortEtherSNMPStatusThe value indicates if the SNMP of Ethernet bridge interface is available
for management.rw Enumeration .radAtm.4.2.7.1.1.6 |
atmSuPortEtherFragmentationFragmentation. When application is not router value must be 'notApplicable'.rw Enumeration .radAtm.4.2.7.1.1.7 |
atmSuPortEtherRIPModeRIP Mode. When application is not router value must be 'notApplicable'.rw Enumeration .radAtm.4.2.7.1.1.8 |
atmSuPortEtherBridgingModeBridging mode can be one of the following:
ATM <> Ethernet - Bridging is between the Ethernet
port and the ATM port (there is no bridging between VCs).
ATM <> Ethernet + ATM - Bridging is done both between
the Ethernet port and the ATM port and also between VCs.
When application is router value must be 'notApplicable'.rw Enumeration .radAtm.4.2.7.1.1.9 |
atmSuPortEtherARPTimeoutARP Timeout. When application is not router or when
this object is not applicable, value must be 0.rw Integer32 .radAtm.4.2.7.1.1.10 |
atmSuPortEtherAgingTimeThe timeout period in seconds for aging out stored information.
valid values are 10...1000000. The value of (0) has
the special meaning - not applicable.rw Integer32 .radAtm.4.2.7.1.1.11 |
atmSuPortEtherPppOEEnableEnable or Disable transparent PPP over ethernet bridge.
When PPP over Ethernet is enabled, non PPP traffic is
blocked by the bridge.rw Enumeration .radAtm.4.2.7.1.1.12 |
atmSuPortEtherStatusThis object allows user to add/remove entries to/from this table.
It will be supported only by certain devices.
destroy - may not be possible for certain interfaces.rw Enumeration .radAtm.4.2.7.1.1.13 |
atmSuCrossConnect OBJECT IDENTIFIER .radAtm.4.3 |
atmSuCrossConnectAtmFr OBJECT IDENTIFIER .radAtm.4.3.1 |
atmSuCrossConnectAtmFrDescriptor OBJECT IDENTIFIER .radAtm.4.3.1.1 |
atmFrCrossConnectNetwork OBJECT IDENTIFIER .radAtm.4.3.1.1.1 |
atmFrCrossConnectService OBJECT IDENTIFIER .radAtm.4.3.1.1.2 |
atmFrDescrTableThis table contains information on ATM to FR Connection
descriptor types, and their associated parameters. SEQUENCE OF AtmFrDescrEntry .radAtm.4.3.1.2 |
atmFrDescrEntryThis list contains ATM to FR Connection descriptor
type, and its associated parameters. AtmFrDescrEntry .radAtm.4.3.1.2.1 |
atmFrDescrIndexThis object is used to identify the row index of
the ATM to FR connection descriptor table.ro Integer32 -- was AtmSuCrossConnectAtmFrDescrIndex .radAtm.4.3.1.2.1.1 |
atmFrDescrTypeThe value of this object identifies the type
of the ATM to FR Connection descriptor.
The type may indicate Network connection descriptor
or a Service connection descriptor with one or more
parameters.
These parameters are specified as a parameter
vector, in the corresponding instances of the
objects:
atmFrDescrClp2De
atmFrDescrDe2Clp
atmFrDescrFecn2Efci
atmFrDescrMappingMode.rw OBJECT IDENTIFIER .radAtm.4.3.1.2.1.2 |
atmFrDescrClp2DeThe first parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.rw Enumeration .radAtm.4.3.1.2.1.3 |
atmFrDescrDe2ClpThe second parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.rw Enumeration .radAtm.4.3.1.2.1.4 |
atmFrDescrFecn2EfciThe third parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.rw Enumeration .radAtm.4.3.1.2.1.5 |
atmFrDescrMappingModeThe fourth parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.rw Enumeration .radAtm.4.3.1.2.1.6 |
atmFrDescrRowStatusThis object is used to create,
modify or delete a row in this table.rw RowStatus (SNMPv2-TC) .radAtm.4.3.1.2.1.7 |
atmSuCrossConnectAtmFrIndexNextThis object contains an appropriate value to
be used for atmFrCnfgCrossConnectIndex when creating
entries in the atmFrCnfgTable. The value
0 indicates that no unassigned entries are
available. To obtain the atmFrCnfgCrossConnectIndex
value for a new entry, the manager issues a
management protocol retrieval operation to obtain
the mandatory value of this object. After each
retrieval, the agent should modify the value to
the next unassigned index.ro Integer32 .radAtm.4.3.1.3 |
atmFrCnfgTableThis table defines virtual connections between ATM and
Frame Relay endpoints. SEQUENCE OF AtmFrCnfgEntry .radAtm.4.3.1.4 |
atmFrCnfgEntryAn entry defines virtual connection between ATM and
Frame Relay endpoint. AtmFrCnfgEntry .radAtm.4.3.1.4.1 |
atmFrCnfgCrossConnectIndexA unique value to identify this cross-connect.ro Integer32 .radAtm.4.3.1.4.1.1 |
atmFrCnfgAtmIfIndexThe ifIndex associated to the ATM interface.ro Integer32 .radAtm.4.3.1.4.1.2 |
atmFrCnfgAtmVpiThe Vpi number of the ATM end point.ro Integer32 .radAtm.4.3.1.4.1.3 |
atmFrCnfgAtmVciThe Vci number of the ATM end point.ro Integer32 .radAtm.4.3.1.4.1.4 |
atmFrCnfgFrIfIndexThe ifIndex associated to the Frame Relay
interface.ro Integer32 .radAtm.4.3.1.4.1.5 |
atmFrCnfgDlciThe DLCI number of the FR end point.ro Integer32 .radAtm.4.3.1.4.1.6 |
atmFrCnfgAdminStatusThis object indicates the connection status requested by the user.rw Enumeration .radAtm.4.3.1.4.1.7 |
atmFrCnfgOperStatusThis object indicates the Operational status of the connection.ro Enumeration .radAtm.4.3.1.4.1.8 |
atmFrCnfgLastChangeThe value of sysUpTime at the time the ATM to FR
connection entered its mandatory operational state.
If the mandatory state was entered prior to the last
re-initialization of the local network management
subsystem, then this object contains a zero value.ro TimeStamp (SNMPv2-TC) .radAtm.4.3.1.4.1.9 |
atmFrCnfgMappingDescrIndexThe value of this object identifies the row
in the atmFrDescrTable.rw Integer32 -- was AtmSuCrossConnectAtmFrDescrIndex .radAtm.4.3.1.4.1.10 |
atmFrCnfgSscsDlciThe DLCI number given to the SSCS Sub-layer for network interworking only
( the default value is 'atmFrCnfgDlci' ).
for Service Interworking do not implement this variable.rw Integer32 .radAtm.4.3.1.4.1.11 |
atmFrCnfgTrafficDescrIndexThe value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.
note :setting this value is allowed only to point2point connections.
for many2one connections is being set by the
atmFrCrossConnectMany2OneRootsTable and this field is equal
to this setting.rw AtmTrafficDescrParamIndex .radAtm.4.3.1.4.1.12 |
atmFrCnfgPriorityThis object define the priority of connection.
The first parameter affects the transmition of cells in Conjested
network is the bitRate( Cbr has the highest priority and then Vbr,Ubr )
In connections with the same bitRate this object will define the priority.rw Enumeration .radAtm.4.3.1.4.1.13 |
atmFrCnfgRowStatusThis object is used to create
a new row or modify or delete an
existing row in this table.rw RowStatus (SNMPv2-TC) .radAtm.4.3.1.4.1.14 |
atmFrCnfgAllocatedBuffersThis object enables user to limit the amount of buffers
used by the connection.
The limit set by this object will give
the effect of a virtual buffer pool per connection.
The user can allocate between 10 to 217 buffers
to every connection. By default the limit is 50 buffers.
Sum of limits allocated to all connections
must not exceed the total amount of available buffers.
Whenever a connection exceeds it's buffer limit
due to congestion or burst - traffic is discardedrw Integer32 .radAtm.4.3.1.4.1.15 |
atmFrMaxMany2OneConnsPerVccThe Maximum Number of many2one cross-connect connections
allowed per Vcc .ro Integer32 .radAtm.4.3.1.5 |
atmSuCrossConnectAtmDxi OBJECT IDENTIFIER .radAtm.4.3.2 |
atmSuCrossConnectAtmDxiIndexNextThis object contains an appropriate value to
be used for atmDxiCnfgCrossConnectIndex when creating
entries in the atmDxiCnfgTable. The value
0 indicates that no unassigned entries are
available. To obtain the atmDxiCnfgCrossConnectIndex
value for a new entry, the manager issues a
management protocol retrieval operation to obtain
the mandatory value of this object. After each
retrieval, the agent should modify the value to
the next unassigned index.ro Integer32 .radAtm.4.3.2.1 |
atmDxiCnfgTableThis table defines virtual connections between ATM and
ATM-DXI endpoints. SEQUENCE OF AtmDxiCnfgEntry .radAtm.4.3.2.2 |
atmDxiCnfgEntryAn entry defines virtual connection between ATM and
ATM-DXI endpoint. AtmDxiCnfgEntry .radAtm.4.3.2.2.1 |
atmDxiCnfgCrossConnectIndexA unique value to identify this cross-connect.ro Integer32 .radAtm.4.3.2.2.1.1 |
atmDxiCnfgAtmIfIndexThe ifIndex associated to the ATM interface.ro Integer32 .radAtm.4.3.2.2.1.2 |
atmDxiCnfgAtmVpiThe Vpi number of the ATM end point.ro Integer32 .radAtm.4.3.2.2.1.3 |
atmDxiCnfgAtmVciThe Vci number of the ATM end point.ro Integer32 .radAtm.4.3.2.2.1.4 |
atmDxiCnfgDxiIfIndexThe ifIndex associated to the atm-dxi interface.ro Integer32 .radAtm.4.3.2.2.1.5 |
atmDxiCnfgDfaThe DFA number of the DXI end point.ro Integer32 .radAtm.4.3.2.2.1.6 |
atmDxiCnfgAdminStatusThe requested state of the ATM to DXI connection.rw Enumeration .radAtm.4.3.2.2.1.7 |
atmDxiCnfgOperStatusThe real operational status of the ATM to DXI connection.ro Enumeration .radAtm.4.3.2.2.1.8 |
atmDxiCnfgLastChangeThe value of sysUpTime at the time the ATM to DXI
connection entered its mandatory operational state.
If the mandatory state was entered prior to the last
re-initialization of the local network management
subsystem, then this object contains a zero value.
Same value define both direction ( Atm2Dxi and Dxi2Atm ).ro TimeStamp (SNMPv2-TC) .radAtm.4.3.2.2.1.9 |
atmDxiCnfgTrafficDescrIndexThe value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.rw AtmTrafficDescrParamIndex .radAtm.4.3.2.2.1.10 |
atmDxiCnfgPriorityThis object define the priority of connection.
The first parameter affects the transmition of cells in Conjested
network is the bitRate( Cbr has the highest priority and then Vbr,Ubr )
In connections with the same bitRate this object will define the priority.rw Enumeration .radAtm.4.3.2.2.1.11 |
atmDxiCnfgRowStatusThis object is used to create a new row or
modify or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .radAtm.4.3.2.2.1.12 |
atmSuAtmCbr OBJECT IDENTIFIER .radAtm.4.3.3 |
atmCbrCnfgTableThis table defines AAL1 virtual connections (not CES)
between ATM port and DS1-CBR port. SEQUENCE OF AtmCbrCnfgEntry .radAtm.4.3.3.1 |
atmCbrCnfgEntryAn entry defines virtual connection between ATM port and
DS1-CBR port. AtmCbrCnfgEntry .radAtm.4.3.3.1.1 |
atmCbrCnfgAtmIfIndexThe ifIndex associated to the ATM interface.ro Integer32 .radAtm.4.3.3.1.1.1 |
atmCbrCnfgAtmVpiThe Vpi number of the ATM end point.ro Integer32 .radAtm.4.3.3.1.1.2 |
atmCbrCnfgAtmVciThe Vci number of the ATM end point.ro Integer32 .radAtm.4.3.3.1.1.3 |
atmCbrCnfgCbrIfIndexThe ifIndex associated to the logical interface of DS0s bundle
or to ifIndex of one of the data ports.ro Integer32 .radAtm.4.3.3.1.1.4 |
atmCbrCnfgAdminStatusThe requested status of the connection.rw Enumeration .radAtm.4.3.3.1.1.5 |
atmCbrCnfgOperStatusThe real operational status of the connection.ro Enumeration .radAtm.4.3.3.1.1.6 |
atmCbrCnfgLastChangeThe value of sysUpTime at the time the ATM to CBR
connection entered its mandatory operational state.
If the mandatory state was entered prior to the last
re-initialization of the local network management
subsystem, then this object contains a zero value.
Same value define both direction ( Atm2Cbr and Cbr2Atm ).ro TimeStamp (SNMPv2-TC) .radAtm.4.3.3.1.1.7 |
atmCbrCnfgAAL1SignallingNot in use. Must be always 'off'.rw Enumeration .radAtm.4.3.3.1.1.8 |
atmCbrCnfgRxTimeSlotsThis value indicates the time-slots used by this connection for receiving.
It uses 32 bits for E1 and low 24 bits for T1.
each bit represents a time slot for receiving :
time-slot 0 = bit 0 (LSB - most right bit in last byte),
...
...
time-slot 31 = bit 31 (MSB - most left bit in first byte ).
value '0' indicate unused time-slot and value '1' indicates used time-slot.
On set-request the user indicates the time-slot he needs for requested ATM-Vcc
by putting '1' to the right bits.
note : time-slots '0' and '16' are used for signalling in E1 interface.
Currently not in use. Must be '0'.rw TimeSlots .radAtm.4.3.3.1.1.9 |
atmCbrCnfgRxBytesPerCellnumber of bytes to be receive in order per cell to low the delay.rw Integer32 .radAtm.4.3.3.1.1.10 |
atmCbrCnfgTxTimeSlotsThis value indicates the time-slots used by this connection for receiving.
It uses 32 bits for E1 and low 24 bits for T1.
each bit represents a time slot for receiving :
time-slot 0 = bit 0 (LSB - most right bit in last byte),
...
...
time-slot 31 = bit 31 (MSB - most left bit in first byte ).
value '0' indicate unused time-slot and value '1' indicates used time-slot.
On set-request the user indicates the time-slot he needs for requested ATM-Vcc
by putting '1' to the right bits.
note : time-slots '0' and '16' are used for signalling in E1 interface.
Currently not in use. Must be '0'.rw TimeSlots .radAtm.4.3.3.1.1.11 |
atmCbrCnfgTxBytesPerCellnumber of bytes to be transmit in order per cell to low the delay.rw Integer32 .radAtm.4.3.3.1.1.12 |
atmCbrCnfgParityControls the use of pointer parity when using
the STRUCTURED or STRUCTURED WITH POINTER connection type.
as defined by atmCbrCnfgService.
ON - Pointer parity bit generation at the transmit side,
and checking of parity bit for error detection at
the receiving side enabled.
Supported only for STRUCTURED or STRUCTURED WITH POINTER service.
OFF - Pointer parity generation and checking disabled.
Supported only for STRUCTURED or STRUCTURED WITH POINTER service.
N/A - Not applicable. This is the only option
when selecting UNSTRUCTURED or STRUCTURED WITHOUT POINTER.rw Enumeration .radAtm.4.3.3.1.1.13 |
atmCbrCnfgRowStatusThis object is used to create a new row or
modify or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .radAtm.4.3.3.1.1.14 |
atmCbrCnfgServiceDefine if DSx service is structured or unstructured.
A structured(3) interface is some nx64Kbps. (n x DS0 = n Time Slots)
An unstructured (2) interface is full DSx, x >0.
(1.544Mbps, 2.048Mbps, 6.312Mbps, 44.736 Mbps, or 34.368 Mbps.)
This objects selects the connection type also
for AAL1 Stream for Data port.
The available selections depend on the data rate
selected.
For the 64 kbps rate:
STRUCTURED WITH POINTER = structure(4)
Use of the structured service as defined in ATMF AF-VTOA-0078.000.
STRUCTURED WITHOUT POINTER : same as above, but without
using a pointer (the resulting cell structure is similar
to that of the unstructured service cells).
Default: STRUCTURED WITH POINTER
structuredControlSignalsTransport -Pointer is used to
transfer Data Control Signals through ATM network.
For other rates:
STRUCTURED : Use of structured service as defined in ATMF AF-VTOA-0078.000.
UNSTRUCTURED : Use of unstructured service as defined in
ATMF document AF-VTOA-0078.000.rw Enumeration .radAtm.4.3.3.1.1.15 |
atmCESConfExtnsTableThis table defines virtual connections between ATM port and
DS1-CBR port. SEQUENCE OF AtmCESConfExtnsEntry .radAtm.4.3.3.2 |
atmCESConfExtnsEntryAn entry defines virtual connection between ATM port and
DS1-CBR port. AtmCESConfExtnsEntry .radAtm.4.3.3.2.1 |
atmCESLastChangeThe value of sysUpTime at the time the ATM to CBR
connection entered its mandatory operational state.
If the mandatory state was entered prior to the last
re-initialization of the local network management
subsystem, then this object contains a zero value.ro TimeStamp (SNMPv2-TC) .radAtm.4.3.3.2.1.1 |
atmCESRxBytesPerCellNumber of bytes to be received per cell, in order to decrease the delay.rw Integer32 .radAtm.4.3.3.2.1.2 |
atmCESTxBytesPerCellNumber of bytes to be transmitted per cell, in order to decrease the delay.rw Integer32 .radAtm.4.3.3.2.1.3 |
atmCESAal1TypeType of CBR connection: CES , DBCES or transparent .rw Enumeration .radAtm.4.3.3.2.1.4 |
atmCESParityIndicate if we'll add even parity to the pointer of the structure of CES.rw Enumeration .radAtm.4.3.3.2.1.5 |
atmCESSigTypetype of signalling for a DBCES connection.
Must be 'other' for CES connection.rw Enumeration .radAtm.4.3.3.2.1.6 |
atmCESSigABBitsThis attribute is applicable only when value of atmCESSigType is other.
Represents the AB bits for Rx/Tx and their masks in this way:
bits 7..6: Tx AB bits value,
bits 5..4: Tx AB bits mask,
bits 3..2: Rx AB bits value,
bits 1..0: Rx AB bits mask.
All bits must be 0 for CES connection.rw OCTET STRING .radAtm.4.3.3.2.1.7 |
atmSuCrossConnectAtmEther OBJECT IDENTIFIER .radAtm.4.3.4 |
atmSuCrossConnectAtmEtherIndexNextThis object contains an appropriate value to
be used for atmEtherCnfgCrossConnectIndex when creating
entries in the atmEtherCnfgTable. The value
0 indicates that no unassigned entries are
available. To obtain the atmEtherCnfgCrossConnectIndex
value for a new entry, the manager issues a
management protocol retrieval operation to obtain
the current value of this object. After each
retrieval, the agent should modify the value to
the next unassigned index.ro Integer32 .radAtm.4.3.4.1 |
atmEtherCnfgTableThis table defines virtual connections between ATM and
ATM-BridgedEthernet endpoints. SEQUENCE OF AtmEtherCnfgEntry .radAtm.4.3.4.2 |
atmEtherCnfgEntryAn entry defines virtual connection between ATM and
ATM-Ethernet endpoint. AtmEtherCnfgEntry .radAtm.4.3.4.2.1 |
atmEtherCnfgCrossConnectIndexA unique value to identify this cross-connect.ro Integer32 .radAtm.4.3.4.2.1.1 |
atmEtherCnfgAtmIfIndexThe ifIndex associated to the ATM interface.ro Integer32 .radAtm.4.3.4.2.1.2 |
atmEtherCnfgAtmVpiThe Vpi number of the ATM end point.ro Integer32 .radAtm.4.3.4.2.1.3 |
atmEtherCnfgAtmVciThe Vci number of the ATM end point.ro Integer32 .radAtm.4.3.4.2.1.4 |
atmEtherCnfgEtherIfIndexThe ifIndex associated to the atm-Ethernet interface.ro Integer32 .radAtm.4.3.4.2.1.5 |
atmEtherCnfgMacAddrThe DFA number of the Ethernet end point.rodeprecated MacAddress (SNMPv2-TC) .radAtm.4.3.4.2.1.6 |
atmEtherCnfgAdminStatusThe requested state of the ATM to Ethernet connection.rw Enumeration .radAtm.4.3.4.2.1.7 |
atmEtherCnfgOperStatusThe real operational status of the ATM to Ethernet connection.ro Enumeration .radAtm.4.3.4.2.1.8 |
atmEtherCnfgLastChangeThe value of sysUpTime at the time the ATM to Ethernet
connection entered its current operational state.
If the current state was entered prior to the last
re-initialization of the local network management
subsystem, then this object contains a zero value.
Same value define both direction ( Atm2Ether and Ether2Atm ).ro TimeStamp (SNMPv2-TC) .radAtm.4.3.4.2.1.9 |
atmEtherCnfgTrafficDescrIndexThe value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.rw AtmTrafficDescrParamIndex .radAtm.4.3.4.2.1.10 |
atmEtherCnfgEncapsulationModeThis object define the encapsulation type requested
for the connection.
it indicates if we transfer the Ethernet frame to the
atm side without the Crc32- AtmBridgedEther,
or with it - AtmBridgedEther-CRC.rwdeprecated Enumeration .radAtm.4.3.4.2.1.11 |
atmEtherCnfgPriorityThis object define the priority of connection.
The first parameter affects the transmition of cells in Conjested
network is the Service Category( Cbr has the highest priority and then Vbr,Ubr )
In connections with the same category this object will define the priority.rw Enumeration .radAtm.4.3.4.2.1.12 |
atmEtherCnfgRowStatusThis object is used to create a new row or
modify or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .radAtm.4.3.4.2.1.13 |
atmEtherCnfgRouterIPThe interface IP address for SNMP requests.rw IpAddress .radAtm.4.3.4.2.1.14 |
atmEtherCnfgRouterMaskThe interface IP address mask for SNMP requests.rw IpAddress .radAtm.4.3.4.2.1.15 |
atmEtherCnfgRouterFragmentationFragmentation. When application is not router value must be 'notApplicable'.rw Enumeration .radAtm.4.3.4.2.1.16 |
atmEtherCnfgRouterRIPModeRIP Mode. When application is not router value must be 'notApplicable'.rw Enumeration .radAtm.4.3.4.2.1.17 |
atmEtherCnfgRouterMTU.rwdeprecated Integer32 .radAtm.4.3.4.2.1.18 |
atmEtherCnfgPPPEncapsulationThis object define the encapsulation type requested
for the connection.
rfc1483 - Multiprotocol Encapsulation over
ATM Adaptation Layer 5 (no PPP)
PPP VC Muxed - For VC Based Multiplexing,
the carried network interconnect protocol is identified
implicitly by the VC connecting the two ATM stations,
i.e. each protocol must be carried over a separate VC.
There is therefore no need to include explicit multiplexing
information in the Payload of the AAL5 CPCS-PDU.
This results in minimal bandwidth and processing overhead.
PPP LLC Muxed - LLC (Low layer compatibility) Encapsulation
is needed when several protocols are carried over the same VC.
In order to allow the receiver to properly process the incoming
AAL5 CPCS-PDU, the Payload Field must contain information necessary
to identify the protocol of the routed or bridged PDU.
In LLC Encapsulation this informationis encoded in an LLC header
placed in front of the carried PDU.rw Enumeration .radAtm.4.3.4.2.1.19 |
atmEtherCnfgAllocatedBuffersThis object enables user to limit the amount of buffers
used by the connection.
The limit set by this object will give
the effect of a virtual buffer pool per connection.
The user can allocate between 10 to 217 buffers
to every connection. By default the limit is 50 buffers.
Sum of limits allocated to all connections
must not exceed the total amount of available buffers.
Whenever a connection exceeds it's buffer limit
due to congestion or burst traffic is discardedrw Integer32 .radAtm.4.3.4.2.1.20 |
atmSuCrossConnectTranslate OBJECT IDENTIFIER .radAtm.4.3.5 |
atmTranslateTableThis table translates the three of AtmIfIndex,AtmVpi,AtmVci
to ifIndex of the interface on the user port's side. SEQUENCE OF AtmTranslateEntry .radAtm.4.3.5.1 |
atmTranslateEntryAn entry includes the User side interface's ifIndex of any virtual
connection along with the ATM connection indices. AtmTranslateEntry .radAtm.4.3.5.1.1 |
atmTranslateAtmIfIndexThe ifIndex associated to the ATM interface.ro Integer32 .radAtm.4.3.5.1.1.1 |
atmTranslateAtmVpiThe Vpi number of the ATM end point.ro Integer32 .radAtm.4.3.5.1.1.2 |
atmTranslateAtmVciThe Vci number of the ATM end point.ro Integer32 .radAtm.4.3.5.1.1.3 |
atmTranslateUserIfIndexThe ifIndex associated to the user interface.ro Integer32 .radAtm.4.3.5.1.1.4 |