AC-ANALOG-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for AC-ANALOG-MIB.
Main OID:
acAnalog.1.3.6.1.4.1.5003.9.10.8
95
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
95 total| Object Name |
|---|
acAnalog MODULE-IDENTITY .1.3.6.1.4.1.5003.9.10.8 |
acAnalogConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1 |
acAnalogConfig OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1.1 |
acAnalogMisc OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1.1.1 |
acAnalogMiscCurrentDisconnectDurationDefines the current-disconnect duration (in msec). This value is used in generation and detection. Access: Offline. AC INI-Param: CurrentDisconnectDurationrw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.1.1.1 |
acAnalogMiscFlashHookPeriodDefines the flashhook period (in msec) for both analog and IP sides. For the analog side it defines: - The maximal hook-flash detection period (for FXS gateways). A longer signal is considered offhook / onhook event. - The hook-flash generation period (for FXO gateways). For the IP side it defines the flash-hook period that is reported to IP. The valid range is 25 to 1500. The default value is 700 msec. Note: For FXO gateways, a constant of 90 msec must be added to the required hook-flash period. For example, to generate a 450 msec hook-flash, set FlashHookPeriod to 540. . Access: Instant. AC INI-Param: FLASHHOOKPERIODrw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.1.1.2 |
acAnalogMiscGroundKeyDetectionEnables/disables the analog ground key detection. 0 = Disable 1= Enable. Access: Offline. AC INI-Param: GroundKeyDetectionrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.1.1.3 |
acAuxiliaryFiles OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1.1.2 |
acAuxiliaryFilesFxsCoefficientsDefines the FXS coefficient file name. AC INI-Param: FXSCOEFFILENAMEro SnmpAdminString .1.3.6.1.4.1.5003.9.10.8.1.1.2.1 |
acAuxiliaryFilesFxoCoefficientsDefines the FXO coefficient filename. Max. 47 characters. AC INI-Param: FXOCOEFFILENAMEro SnmpAdminString .1.3.6.1.4.1.5003.9.10.8.1.1.2.2 |
acAnalogFxoConfig OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1.2 |
acAnalogFxo OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1.2.1 |
acAnalogFxoFarEndDisconnectTypeThis parameter sets the source for the acEV_FAR_END_DISCONNECTED event (or for the relevant control protocol event). It is a bit field parameter, hence (for example) if both CPT and current disconnect are required, the parameter should be set to 5. FarDisconnect contributor: 1 = CPT 2 = PolarityReversal 4 = CurrentDisconnect 8 = Silence. Access: Offline. AC INI-Param: FARENDDISCONNECTTYPErw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.2.1.1 |
acAnalogFxoCountryCoefficientsAllows the user to modify the line characteristic (AC and DC) according to country. Access: Offline. AC INI-Param: CountryCoefficientsrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.2.1.2 |
acAnalogFxoDCRemoverDetermines whether to enable the analog DC remover in the DAA. One of the following values: 0 = DC remover is disabled 1 = DC remover is enabled. Access: Offline. AC INI-Param: EnableAnalogDCRemoverrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.2.1.3 |
acAnalogFxoFarEndDisconnectToneTable SEQUENCE OF AcAnalogFxoFarEndDisconnectToneEntry .1.3.6.1.4.1.5003.9.10.8.1.2.1.21 |
acAnalogFxoFarEndDisconnectToneEntry AcAnalogFxoFarEndDisconnectToneEntry .1.3.6.1.4.1.5003.9.10.8.1.2.1.21.1 |
acAnalogFxoFarEndDisconnectToneRowStatusFar End Disconnect table row-status. AC INI-Param: N/Arw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.2.1.21.1.1 |
acAnalogFxoFarEndDisconnectToneActionFar End Disconnect table action. AC INI-Param: N/Arw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.2.1.21.1.2 |
acAnalogFxoFarEndDisconnectToneActionResultFar End Disconnect table result. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.2.1.21.1.3 |
acAnalogFxoFarEndDisconnectToneIndexIndex for table use. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.2.1.21.1.4 |
acAnalogFxoFarEndDisconnectToneTypeDefines which CPT types are detected as far-end disconnect. The CPT type is based on the acTCallProgressToneType enum. This is valid when FarEndDisconnectType allows CPT detection. Range = An array of up to 4 tone types. Access: Offline. AC INI-Param: DISCONNECTTONETYPErw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.2.1.21.1.5 |
acAnalogFxsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1.3 |
acAnalogFxs OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.1.3.1 |
acAnalogFxsPolarityReversalTypeSets the type of the polarity reversal signal used for the network far-end answer and disconnect indications. Smooth reversal prevents negative effects as non-required ringing. 0 = Soft reverse polarity 1 = Hard reverse polarity. Access: Offline. AC INI-Param: POLARITYREVERSALTYPErw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.1 |
acAnalogFxsMeteringTypeSets the metering method for charging pulses. 0 = 12 kHz sinusoidal bursts 1 = 16 kHz sinusoidal bursts 2 = Polarity Reversal pulses. Access: Offline. AC INI-Param: METERINGTYPErw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.2 |
acAnalogFxsLifeLineTypeDefines the Lifeline phone type. The Lifeline phone is available (for FXS only) on port 4 in MP-104 and MP-108, on port 2 in MP-102, on ports 1-4 in the MP-118, and on port 2 of each analog module in the Mediant 1000. 0 = activate Lifeline phone on power down 1 = activate Lifeline phone on power down or on detection of LAN disconnect 2 = activate Lifeline phone on power down, or on detection of LAN disconnect, or on loss of ping. Access: Offline. AC INI-Param: LIFELINETYPErw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.3 |
acAnalogFxsMinFlashHookTimeSets the minimal time (in msec) for detection of a flash-hook event (for FXS only). The valid range is 25 to 300. The default value is 300 msec. Detection is guaranteed for flash hook periods of at least 60 msec (when setting the minimal time to 25). Flash-hook signals that last a shorter period of time are ignored. Note: It is recommended to reduce the detection time by 50 msec from the desired value (e.g. if you set the value as 200 msec, then enter 150 msec, i.e. 200 minus 50). . Access: Offline. AC INI-Param: MINFLASHHOOKTIMErw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.3.1.4 |
acAnalogFxsCallerIDTimingModeDefines the Analog CallerID Timing Mode. 0 = CallerID transferred between first and second rings 1 = CallerID transferred on valid Off ring. Access: Offline. AC INI-Param: ANALOGCALLERIDTIMINGMODErw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.5 |
acAnalogFxsBellcoreCallerIDTypeOneSubStandardSelects the sub-standard of the Bellcore Caller ID type. 0 = Between_Rings 1 = Not_Ring_Related 2 = Before_Ring_RP_AS. Access: Offline. AC INI-Param: BellcoreCallerIDTypeOneSubStandardrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.6 |
acAnalogFxsETSICallerIDTypeOneSubStandardSelects the number denoting the ETSI CallerID Type 1 sub-standard. Either: 0 = ETSI_Between_Rings 1 = ETSI_Before_Ring_DT_AS 2 = ETSI_Before_Ring_RP_AS 3 = ETSI_Before_Ring_LR_DT_AS 4 = ETSI_Not_Ring_Related_DT_AS 5 = ETSI_Not_Ring_Related_RP_AS 6 = ETSI_Not_Ring_Related_LR_DT_AS. Access: Offline. AC INI-Param: ETSICallerIDTypeOneSubStandardrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.7 |
acAnalogFxsETSIVMWITypeOneStandardSelects the number denoting the ETSI VMWI Type 1 Standard. Choose: 0 = ETSI_VMWI_Between_Rings 1 = ETSI_VMWI_Before_Ring_DT_AS 2 = ETSI_VMWI_Before_Ring_RP_AS 3 = ETSI_VMWI_Before_Ring_LR_DT_AS 4 = ETSI_VMWI_Not_Ring_Related_DT_AS 5 = ETSI_VMWI_Not_Ring_Related_RP_AS 6 = ETSI_VMWI_Not_Ring_Related_LR_DT_AS. Access: Offline. AC INI-Param: ETSIVMWITypeOneStandardrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.8 |
acAnalogFxsBellcoreVMWITypeOneStandardUse this parameter to select the Bellcore VMWI standard. 0 - Between_Rings 1 - Not_Ring_Related. Access: Offline. AC INI-Param: BellcoreVMWITypeOneStandardrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.9 |
acAnalogFxsDisableAutoCalibrationDetermines whether to enable the analog Autocalibration in the DAA. One of the following values: 0 = Auto calibration is enabled 1 = Auto calibration is disabled. Access: Offline. AC INI-Param: DisableAnalogAutoCalibrationrw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.3.1.10 |
acAnalogFxsExternalLifeLinePortsSet the amount of FXS ports which will be connected to an external life line and will be disabled (max value is half of the FXS ports). Access: Offline. AC INI-Param: ExternalLifeLinePortsrw Unsigned32 .1.3.6.1.4.1.5003.9.10.8.1.3.1.11 |
acAnalogFxsCountryCoefficientsAllows the user to modify the line characteristic (AC and DC) according to country. Access: Offline. AC INI-Param: FXSCountryCoefficientsrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.12 |
acAnalogFxsTTXVoltageLevelSets the TTX pulses voltage level. 0 = 0Vrms sinusoidal bursts 1 = 0.5Vrms sinusoidal bursts 2 = 1Vrms sinusoidal bursts -1 = notAvailable. Access: Offline. AC INI-Param: AnalogTTXVoltageLevelrw Enumeration .1.3.6.1.4.1.5003.9.10.8.1.3.1.13 |
acAnalogStatus OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.2 |
acAnalogStatusMisc OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.2.1 |
acAnalogStatusMiscFxsOrFxoBoard is Fxs Or Fxo (For all devices except MP118). For MP118 - see acAnalogFxsFxoType for a line specific status. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.2.1.1 |
acAnalogStatusMiscBoardTemperatureTemperature of the board in degrees Celsius, should not go higher then 60!. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.1.2 |
acAnalogStatusMiscAnalogChannelsCountNumber of the Analog channels in the board. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.1.3 |
acAnalogFxsFxo OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.2.20 |
acAnalogFxsFxoTable SEQUENCE OF AcAnalogFxsFxoEntry .1.3.6.1.4.1.5003.9.10.8.2.20.1 |
acAnalogFxsFxoEntry AcAnalogFxsFxoEntry .1.3.6.1.4.1.5003.9.10.8.2.20.1.1 |
acAnalogFxsFxoIndexIndex for table use. AC INI-Param: N/A Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.20.1.1.1 |
acAnalogFxsFxoTypeLine is Fxs Or Fxo. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.2.20.1.1.2 |
acAnalogFxsFxoChipRevNumFxs/Fxo's Chip revision number. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.20.1.1.3 |
acAnalogFxsFxoHookStateThe hook state of the analog line. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.2.20.1.1.4 |
acAnalogLegs OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.2.21 |
acAnalogLegsTable SEQUENCE OF AcAnalogLegsEntry .1.3.6.1.4.1.5003.9.10.8.2.21.1 |
acAnalogLegsEntry AcAnalogLegsEntry .1.3.6.1.4.1.5003.9.10.8.2.21.1.1 |
acAnalogLegsLegIndexDecribes The Digital EndPoint In A Call. AC INI-Param: N/A Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.1 |
acAnalogLegsCallIndexDecribes The Call which The Rtp EndPoint Participant In It. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.2 |
acAnalogLegsAnalogTypeDescribs whether the board is FXS or FXO. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.3 |
acAnalogLegsEchoCancellerEnables or Disables the Echo Canceller. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.4 |
acAnalogLegsHighPassFilterEnables or Disables theHigh Pass Filter. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.5 |
acAnalogLegsDTMFDetectionEnables or Disables the DTMF Detection. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.6 |
acAnalogLegsVoiceVolumeDescribs the volume of the voice in dB. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.7 |
acAnalogLegsInputGainDescribes the Input Gain on the leg in dB. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.8 |
acAnalogLegsLegNameDescribes the Leg Name as in the Control Protocol. AC INI-Param: N/Aro SnmpAdminString .1.3.6.1.4.1.5003.9.10.8.2.21.1.1.9 |
acAnalogAction OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.3 |
acAnalogFxoAction OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.3.1 |
acAnalogFxoLineTestTable SEQUENCE OF AcAnalogFxoLineTestEntry .1.3.6.1.4.1.5003.9.10.8.3.1.1 |
acAnalogFxoLineTestEntry AcAnalogFxoLineTestEntry .1.3.6.1.4.1.5003.9.10.8.3.1.1.1 |
acAnalogFxoLineTestIndexIndex for table use. AC INI-Param: N/A Unsigned32 .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.1 |
acAnalogFxoLineTestActivateActivate line testing in an FXO analog line according to a given line-index. AC INI-Param: N/Arw Enumeration .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.2 |
acAnalogFxoLineTestHookStateThe hook state of the analog line. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.3 |
acAnalogFxoLineTestPolarityStatusThe line's polarity state. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.4 |
acAnalogFxoLineTestLineConnectionStatusThe connection's status of the line. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.5 |
acAnalogFxoLineTestLineCurrentThe line's current [ma]. AC INI-Param: N/Aro Integer32 (-1..24) .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.6 |
acAnalogFxoLineTestLineVoltageThe line's voltage [V]. AC INI-Param: N/Aro Integer32 (-128..128) .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.7 |
acAnalogFxoLineTestRingStateThe Ring's State. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.8 |
acAnalogFxoLineTestLinePolarityThe line's polarity state. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.9 |
acAnalogFxoLineTestMwiStateMwi's state. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.10 |
acAnalogFxoLineTestLastCurrentDisconnectDurationLast current disconnect duration in msec. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.3.1.1.1.11 |
acAnalogFxsAction OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.3.2 |
acAnalogFxsLineTestTable SEQUENCE OF AcAnalogFxsLineTestEntry .1.3.6.1.4.1.5003.9.10.8.3.2.1 |
acAnalogFxsLineTestEntry AcAnalogFxsLineTestEntry .1.3.6.1.4.1.5003.9.10.8.3.2.1.1 |
acAnalogFxsLineTestIndexIndex for table use. AC INI-Param: N/A Unsigned32 .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.1 |
acAnalogFxsLineTestActivateActivate line testing in a FXS analog line according to a given line-index. AC INI-Param: N/Arw Enumeration .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.2 |
acAnalogFxsLineTestHookStateThe hook state of the analog line. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.3 |
acAnalogFxsLineTestRingStateLine's ring state. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.4 |
acAnalogFxsLineTestPolarityStatusLine's reversal-polarity. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.5 |
acAnalogFxsLineTestMessageWaitingIndicationLine's messgae waiting indication state. AC INI-Param: N/Aro Enumeration .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.6 |
acAnalogFxsLineTestLineCurrentReadingThe Line current reading in 10ua units. This test is supported only in line no. 0. Not supported on MP500. In case of MP124 this test is supported in all ports except ports 2 and 3. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.7 |
acAnalogFxsLineTestLineVoltageReadingThe Line voltage reading in 10mV units. In case of MP124 the Line voltage reading in 1V units. This test is supported only in line no. 0. Not supported on MP500. In case of MP124 this test is supported in all ports except ports 2 and 3. AC INI-Param: N/Aro Integer32 (-6000..6000) .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.8 |
acAnalogFxsLineTestAnalogVoltageReadingThe current analog voltage reading in 10mV units. his test is supported only in line no. 0. Not supported on MP500. In case of MP124 this test is supported in all ports except ports 2 and 3. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.9 |
acAnalogFxsLineTestRingVoltageReadingThe current ring voltage reading in 10mV units. This test is supported only in line no. 0. Not supported on MP500. In case of MP124 this test is supported in all ports except ports 2 and 3. AC INI-Param: N/Aro Integer32 (-13000..13000) .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.10 |
acAnalogFxsLineTestLongLineCurrentReadingThe current long line reading in 10ua units. This test is supported only in line no. 0. Not supported on MP500. In case of MP124 this test is supported in all ports except ports 2 and 3. AC INI-Param: N/Aro Unsigned32 .1.3.6.1.4.1.5003.9.10.8.3.2.1.1.11 |
acAnalogCommonAction OBJECT IDENTIFIER .1.3.6.1.4.1.5003.9.10.8.3.3 |
acAnalogCommonChannelTableTable for common channels operations. SEQUENCE OF AcAnalogCommonChannelEntry .1.3.6.1.4.1.5003.9.10.8.3.3.1 |
acAnalogCommonChannelEntry AcAnalogCommonChannelEntry .1.3.6.1.4.1.5003.9.10.8.3.3.1.1 |
acAnalogCommonChannelIndexIndex for table use, the current channel. AC INI-Param: N/A Unsigned32 .1.3.6.1.4.1.5003.9.10.8.3.3.1.1.1 |
acAnalogCommonChannelActionAn action to make on the current channel, The Reset action is for Analog channels only. AC INI-Param: N/Arw Enumeration .1.3.6.1.4.1.5003.9.10.8.3.3.1.1.2 |