Home/Catalog/AcBoard

AcBoard

AI MIB Summary

The AcBoard MIB module enables remote configuration, firmware reset, and real-time operational monitoring of AudioCodes hardware boards, specifically tracking channel voice/fax states, DSP packet counters, and error metrics. It facilitates the application of persistent board configuration parameters and provides critical status notifications for board initialization and reset events.

AudioCodes Proprietary MIB Contains The managed objects of AudioCodes systems. Through this MIB, the User can set up the board configuration parameters, reset the board, and monitor the board's operational robustness and quality of service during run-time. This MIB has the following Groups: boardConfiguration boardInformation channelConfiguration channelStatus notifications reset boardConfiguration: When The user Get Parameter from most of sub-groups in boardConfiguration group, he gets the value that should be burned to the board after the next Remote Reset. He can Set new values to many parameters, and these values will burned to the board after the next remote Reset In the sub-group mGCPDefaultChannelSettings the parameters are the actual parameters, that will take place when opening channel. (Reset is not needed for that sub-group). BoardInformation: Contains Read-only parameters like: board name, serial number, number of channels, software version. ChannelConfiguration: Read-only Parameters to see the configuratin of each channel: voice settings, fax settings, etc. ChannelStatus: Read-only parameters about the status of channel, like: Is the channle active, is it in Silence Period, is it in Fax mode, ON/Off hook, etc. This group contains also counters: packets to DSP, errors, lost packets, underruns, etc. Notifications: In this version, the notification we have are: acEvBoardStarted, and acEvResetingBoard. The board should send these notifications to its manager that the user defined in INI file with the parameter: NMPManagerIP = (IP address). Reset: To remote reset the board, the user should set an integer value to the parameter remoteReset. Then he should get the trap acEvResettingBoard. Note: Before Reset, The current boardConfiguration parameters will be burned to the board. The user should not use INI file, if he wants these parameters to take place. To set the default values, the user should set an integer value to the parameter acSetDefaults.
Main OID:
acBoard.1.3.6.1.4.1.5003.9.10.1
423
Objects
Active
Status
3
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
RFC1155-SMI

Objects

423 total
Object Name
audioCodes
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003
acRegistrations
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.7
acGeneric
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.8
acProducts
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9
acBoardMibs
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10
acBoardAudioCodes Proprietary MIB Contains The managed objects of AudioCodes systems. Through this MIB, the User can set up the board configuration parameters, reset the board, and monitor the board's operational robustness and quality of service during run-time. This MIB has the following Groups: boardConfiguration boardInformation channelConfiguration channelStatus notifications reset boardConfiguration: When The user Get Parameter from most of sub-groups in boardConfiguration group, he gets the value that should be burned to the board after the next Remote Reset. He can Set new values to many parameters, and these values will burned to the board after the next remote Reset In the sub-group mGCPDefaultChannelSettings the parameters are the actual parameters, that will take place when opening channel. (Reset is not needed for that sub-group). BoardInformation: Contains Read-only parameters like: board name, serial number, number of channels, software version. ChannelConfiguration: Read-only Parameters to see the configuratin of each channel: voice settings, fax settings, etc. ChannelStatus: Read-only parameters about the status of channel, like: Is the channle active, is it in Silence Period, is it in Fax mode, ON/Off hook, etc. This group contains also counters: packets to DSP, errors, lost packets, underruns, etc. Notifications: In this version, the notification we have are: acEvBoardStarted, and acEvResetingBoard. The board should send these notifications to its manager that the user defined in INI file with the parameter: NMPManagerIP = (IP address). Reset: To remote reset the board, the user should set an integer value to the parameter remoteReset. Then he should get the trap acEvResettingBoard. Note: Before Reset, The current boardConfiguration parameters will be burned to the board. The user should not use INI file, if he wants these parameters to take place. To set the default values, the user should set an integer value to the parameter acSetDefaults.
MODULE-IDENTITY
.1.3.6.1.4.1.5003.9.10.1
boardConfiguration
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1
boardTDMBusSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.1
pCMLawSelectSelects the type of PCM companding law in input/output TDM bus (TDM bus is defined using the TDMBusType parameter).rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.1
tDMBusClockSourceSelects the clock source on which the board synchronizesrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.2
tDMBusEnableFallBackEnable/Disable clock fallback. The Fall Back clock is determined by BSPTDMBusFallbackClockrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.3
tDMBusLocalReferenceWhen ClockSource is set to acH110BusClockSource_Network this parameter selects the TrunkID to be used as the clock synchronization source of the board. When using H.110/H.100 bus this parameter also selects the trunk which is used as the clock source for the NETREF clock generation (in this case ClockSource might not be set to acH110BusClockSource_Network).rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.1.4
idlePCMPatternPCM Pattern applied to E1/T1 timeslot (B-channel) when channel is idle.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.1.5
idleABCDABCD (CAS) Pattern to be applied to CAS signaling bus before changed by the user or PSTN protocol. This is only relevant when using PSTN interface with CAS protocols.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.1.6
tDMBusMasterSlaveSelectionSet SC/MVIP/H.110 to either: Master mode (the board is the clock source for the TDM bus) or Slave mode (some other board in the system must supply the clock to the TDM bus).rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.7
tDMBusNetRefSpeedDetermine the NetRef frequency (for both generation and synchronization).rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.8
tDMBusOutputStartingChannelDefines the outgoing TDM Timeslot of the first channel (ChannelId=0). The remaining channels are organized sequentially.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.1.9
boardTDMBusOutputPortDefines the SC/MVIP/H.100/H.110 port to be used for board's channel #0. All other channels then occupy the next timeslots sequentiallyrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.1.10
tDMBusSpeedSelects the TDM Bus Speed. Speed is set according to the Bus Type. The following are allowed speeds for each bus type: SC = 0/2/3 H.110/H.100 = 3 MVIP = 0rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.11
tDMBusTypeSelects the TDM bus interface to be used (only one TDM bus interface can be enabled at one time although more than one can physically exist on the board).rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.12
acOverrideDefaultIdlePCMPatternOverride Default Idle PCM Pattern. 0 - use defaults (0xff-Mulaw, 0x55-Alaw) 1 - use IdlePCMPattern.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.13
acOverrideDefaultIdleABCDPatternDescription: Override Default Idle ABCD Pattern. 0 - use defaults (0xf) 1 - use IdleABCDPattern.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.1.14
networkSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.2
baseUDPPortLower boundary of UDP ports to be used by the board. The upper boundary is BoardBaseUDPPort+10*(Number of Channels). Must be a multiple of 10.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.1
defaultGatewayAddrDefault Gateway Address. Board's Default Gateway IP address. (in host byte order e.g. 192.10.1.255 = 0xc00a01ff).roobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.2.2
boardIPAddrBoard IP Address. in host byte order e.g. 192.10.1.2 = 0xc00a0102). Users should set the subnet mask to a valid value per the IP address.roobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.2.3
boardSubNetAddrBoard SubNet Address. (in host byte order e.g. 255.255.255.0 = 0xffffff00). default =255.255.255.0.roobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.2.4
acSyslogServerIPIP address in dotted format notation, e.g., 192.10.1.255rwobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.2.5
acMGControlProtocolTypeThis parameter defines the control protocol type 0 = none, 1 = MGCP, 2 = MEGACO, 4 = H323, 8 = SIPrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.2.6
acSNMPManagerIPSNMP manager server IP addressrwobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.2.7
acDisableWEBConfigEnables or disables Web Configuration 0-Read & Write mode(default) 1-Read Only moderwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.2.8
acEnableSyslogEnable SysLog protocol log.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.2.9
acContrlProtocolTransportTypeDefines the transport type for the control: 0 - UDP, 1 - TCP (SCTP on road map).rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.2.10
acCPControlDiffServDefines the value of the 'DiffServ' field in the IP header for the control session.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.11
snmpManagers
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.2.21
snmpManagersTableSnmp Managers Tableobsolete
SEQUENCE OF SnmpManagersEntry
.1.3.6.1.4.1.5003.9.10.1.1.2.21.1
snmpManagersEntryobsolete
SnmpManagersEntry
.1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1
snmpManagerIndexSnmp Manager Indexroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.1
snmpManagerIsUsedEnable the SNMP Manager to recieve traps.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.2
snmpManagerIpIP address of default SNMP manager in dotted notation format: xxx.xxx.xxx.xxx. SNMP traps are sent to this manager.rwobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.3
snmpManagerTrapPortSets the trap ports to be used by the different managers.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.4
snmpManagerTrapSendingEnableEnable the SNMP Manager to recieve traps.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.2.21.1.1.5
acNTPSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.2.22
acNTPServerIPAddressNTP Server IP address.rwobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.2.22.1
acNTPUtcOffsetNTP time to offset in seconds. Default is 0. Range - Between -43200 ot 43200 seconds.rwdeprecated
INTEGER (-43200..43200)
.1.3.6.1.4.1.5003.9.10.1.1.2.22.2
acNTPUpdateIntervalNTPupdate interval in seconds. Default is 86400 (24 hours). Not recommended to be set beyond one month (2592000 sec).rwdeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.22.3
acWEBAccess
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.2.23
acWEBAccessTableobsolete
SEQUENCE OF AcWEBAccessEntry
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1
acWEBAccessEntryobsolete
AcWEBAccessEntry
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1
acWEBAccessRowStatusWEB Access row-statusrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.1
acWEBAccessActionWEB Access actionrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.2
acWEBAccessActionResultWEB Access action resultroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.3
acWEBAccessIndexWEB Access indexroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.4
acWEBAccessUserNameWEB Access user namerwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.5
acWEBAccessUserCodeWEB Access user coderwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.2.23.1.1.6
auxiliarySettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.3
enableDiagnosticsThe EnableDiagnostics checks the correct functionality of different hardware components on the board. Upon completion, the board sends EV_END_BIT which contains information on the results of the test of each hardware component.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.3.1
trunkSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.4
trunkSettingsTableTrunks Tableobsolete
SEQUENCE OF TrunkSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.1.4.1
trunkSettingsEntryobsolete
TrunkSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1
trunkIdTrunk ID at board in which the call is taking placeroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.1
clockMasterSelects the trunk clock source. When choosing acCLOCK_MASTER_OFF (= 0) the clock is recovered from the line. When choosing acCLOCK_MASTER_ON (= 1) the trunk clock source is provided by the internal/TDM bus clock source depending on the TDMBusClockSource parameter.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.2
framingMethodSelects the Framing method to be used for this trunk.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.3
protocolTypeProtocol Type. Sets the PSTN protocol to be used for this trunk. The protocol type parameter defines the interface and the specific telephony protocol. Each protocol defines the following: 1. E1 or T1 physical line configuration. 2. Fixed connection of the relevant time-slots, which are the Trunks' B-channels, mapping to the 60 (128 for TrunkPack-VoIP/400) DSP channels. This limitation is about to change in versions higher than 3.4. 3. Layer 3 specific telephony protocol or transparent mode of operation. Currently only identical configurations (protocol type, framing method, etc.) for the two trunks are supported.(see at the TrunkPack-VoIP User Manual for available protocols families) relevant only when TDMBusType=FRAMERS.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.4
terminationSideFor ISDN only. select the ISDN Termination side (layer 2)rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.5
dchConfigDefines D-channel configuration. This setting is only applicable to ISDN PRI protocols that support NFAS and/or D-channel backup procedures.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.6
lineCodeUse to select line code. B8ZS or AMI for T1 spans and HDB3 or AMI for E1 spans.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.7
lineBuildOutLossSelects the line build out loss to be used for this trunkrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.8
lineBuildOutOverwriteOverwrite the framer's XPM registers values (these registers control the line pulse shape).rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.9
lineBuildOutXPM0Controls the Framer's XPM0 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1.Should be used only by expert Users.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.10
lineBuildOutXPM1Controls the Framer's XPM1 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert Users.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.11
lineBuildOutXPM2Controls the Framer's XPM2 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1.Should be used only by expert Users.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.12
traceLevelDefines the Protocol Trace levelrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.13
acV5InterfaceTrunkGroupIdcopy from Table 8-1 in LIB manual 4.2betaroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.14
acV5LinkIdOldcopy from Table 8-1 in LIB manual 4.2betarwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.15
acPMStatusperformance Monitoring Enable/Disable.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.16
acLedStatusColorTrunk led status colorroobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.17
acLedStatusRateTrunk led status blinking rateroobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.18
acIsdnNfasInterfaceIdDefines the Interface ID works with NS_EXPLICIT_INTERFACE_ID bit. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.19
acTrunkCasTableIndexIndex of Cas Table used by this Trunkrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.20
acTrunkAdminStateTrunk Administrative Staterwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.21
acPSTNIuaInterfaceIdIUA trunk interface ID valuerwobsolete
INTEGER (-1..2147483647)
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.22
acIsdnQ931LayerResponseBehaviorBit-field used to determine several behavior options, which influence how the Q.931 protocol behaves.rwobsolete
INTEGER (-2147483647..2147483647)
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.23
acIsdnIncomingCallsBehaviorThis is the bit-field used to determine several behavior options that influence how the ISDN Stack INCOMING calls behave. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.24
acIsdnOutgoingCallsBehaviorThis is the bit-field used to determine several behavior options that influence how the ISDN Stack OUTGOING calls behave. Refer to Appendix A.8 in the 'VoPLib Reference Library User's Manual.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.25
acIsdnGeneralCCBehaviorThis is the bit-field used to determine several general ISDN behavior options. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.26
acIsdnNfasGroupNumberRelevant only for T1 ISDN NFAS trunks indicates the group number of the NFAS group. ;Valid NFAS group numbers are only 1 to 4, 0 indicating that this trunk is not NFAS (in this case the ISDNNFASInterfaceID and DchConfig parameters are ignored).rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.4.1.1.27
mGCPSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.5
callAgentIPMGCP Call Agent IP address to be used for the initial RestartInProgress MGCP message (RSIP) (e.g., 192.10.1.255). Set to 0.0.0.0 to avoid sending RSIP. This parameter if in use overrides the Call Agent IP address provided in BootP.rwobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.5.1
callAgentPortGate Way will use CallAgentPort as default UDP Port of MGCP Call Agent.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.5.2
callAgentDomainNameMGCP Call Agent domain name.rwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.5.3
redundantAgentIPRedundant MGCP call agent IP address for initial RestartInProgress MGCP message (RSIP) e.g. 192.10.1.255. Set to 0 to avoid sending RSIP.rwobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.5.4
redundantAgentPortUDP Port of Redundant MGCP call agent.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.5.5
redundantCallAgentDomainNameRedundant MGCP Call Agent Domain namerwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.5.6
dePopulatedChannelsNumberThis parameter can be used to enable MGCP call agent to access only subset of the on board channel bank. Set to -1 (or do not specify) to use all channels.rwobsolete
INTEGER (-1..2147483647)
.1.3.6.1.4.1.5003.9.10.1.1.5.7
gateWayNameGateWay Namerwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.5.8
endPointNameMGCP: Gateway's end point name. This is a prefix used to identify the endpoint, i.e., 'ACgw' in the following example: 'ACgw5@acl.com'. MEGACO: Prefix of the endpoint part of the termination namerwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.5.9
mGCPCommunicationLayerTimeoutAssumed delay of the communication layer. It is used in retransmission.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.5.10
acDefaultChannelSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.6
acChDefaultDJBufMinDelayDynamic Jitter Buffer Minimum Delay (msec)rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.1
acChDefaultDJBufOptFactorDynamic Jitter Buffer frame error/delay optimization.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.2
acChDefaultCallerIDTypeThe supported caller ID standard typesrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.3
acChDefaultFaxModemBypassMNumber of basic frames to generating one RTP fax/modem bypass packet.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.4
acChDefaultFaxModemRelayVolumeFax gain control. The range -18 to -3 relates to -18.5 dBm to -3.5 dBm in 1 dBm steps.rwobsolete
INTEGER (-18..-3)
.1.3.6.1.4.1.5003.9.10.1.1.6.5
acChDefaultFaxRelayECMEnableEnables or disables the using of ECM mode during Fax Relay.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.6
acChDefaultFaxRelayMaxRateLimits the maximum rate at which fax messages are transmitted.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.7
acChDefaultFaxTransportModeSets the Fax over IP transport method.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.8
acChDefaultModemRelayRedundancyDepthAmount of redundancy for fax relay packetsrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.9
acChDefaultModemRelayMaxRateDefault: Modem Relay Max Raterwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.10
acChDefaultUseT38orFRF11Selects protocol to send/ receive fax relay.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.11
acChDefaultV21ModemTransportTypeSets the V.21 modem transport method (must be set to 0 = disable)rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.12
acChDefaultV22ModemTransportTypeSets the V.22 modem transport methodrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.13
acChDefaultV23ModemTransportTypeSets the V.23 modem transport methodrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.14
acChDefaultV32ModemTransportTypeSets the V.32 modem transport methodrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.15
acChDefaultV34ModemTransportTypeSets the V.34 modem transport methodrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.16
acChDefaultFaxModemBypassCoderTypeThe User can set the bypass coder (according to the known coders)rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.17
acChDefaultFaxRelayRedundancyDepthDefault: Fax Relay Redundancy Depth. Number of repetitions to be applied to each fax relay payload when transmitting to network.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.18
acChDefaultT38ProtectionModeDefault: T38 Protection Mode. Use Forward Error Correction (FEC) algorithm to protect T.38 fax relay stream.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.19
acChDefaultDTMFVolumeDTMF generation Volume Controlrwobsolete
INTEGER (-31..0)
.1.3.6.1.4.1.5003.9.10.1.1.6.20
acChDefaultDTMFTransportType0 = Mute = erases digit from voice stream does not relay to remote. 2 = Transparent = digits remains in voice stream. 3 = RFC 2833 relay = erase digit from voice stream relay to remote using RFC 2833 syntax. The other values as seen in the Value List (1 and 7) are not supported as of version 4.4.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.21
acChDefaultMFTransportType0 = erase MFs from voice transport not relayed to remote. 2 = MFs not erased not relayed to remote. 3 = MFs are muted from the voice stream & relayed according to RFC 2833.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.22
acChDefaultInputGainPCM input gain. The range is 31 dB to +31 dB in 1 dB steps.rwobsolete
INTEGER (-32..31)
.1.3.6.1.4.1.5003.9.10.1.1.6.23
acChDefaultRTPRedundancyDepthEnables or disables generation of RFC 2198 redundancy packets.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.24
acChDefaultTestModeTesting mode applied. 0 = Coder Loopback performs an encoder/decoder loopback inside DSP device. 1 = PCMLoopback loops back incoming PCM to the outgoing PCM. 2 = ToneInjection generates a 1000 Hz tone to outgoing PCM. 3 = NoLoopback sets the channel to work in normal mode.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.25
acChDefaultVoiceVolumeVoice output gain control the range is -31 dB to +31 dB in 1 dB steps -32 = mute.rwobsolete
INTEGER (-32..31)
.1.3.6.1.4.1.5003.9.10.1.1.6.26
acChDefaultMNumber of DSP payloads for generating one RTP packetrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.27
acChDefaultFlashHookPeriodFlash hook period.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.28
acChDefaultDTMFDetectionPointDefines if the detection of DTMF events is notified at the end of DTMF or at the start of DTMF.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.29
acChDefaultRtpIpTosSets value of IP Type Of Service field in IP header for all packets generated from this channel. Follow the acTIPTOS enumeration.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.30
acChDefaultRtpIpPrecedenceSets value of the IP precedence field in the IP header for all packets generated from this channel. Follow the acTIPPrecedence enumeration.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.31
acChDefaultEchoCanclerControls the activation of the Echo Canceler (refer also to 'ForceEchoOff')rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.32
acChDefaultSilenceSuppressionSilence Suppression moderwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.33
acChDefaultEchoCanclerHybridLossSets worst case ratio between signal level transmitted to hybrid & echo level returning from hybrid. Set this per worst hybrid in the system in terms of echo return loss. Refer to acTECHybridLoss enumeration:rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.6.34
acChDefaultPacketizationPeriodPacketization Periodrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.6.35
aTMSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.7
vPMaskVP masking bits used for address resolutionrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.1
vCMaskVC masking bits used for address resolutionrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.2
externalClkSource clock of on the board UTOPIA busrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.3
aTMLoopBackPhy loopback. The loopback can be used for testing purposes. The loopback direction is towards the PSTN siderwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.4
utopiaSlaveUTOPIA interface mode of bus arbitrationrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.5
multyPhyUTOPIA interface SinglePhy or MultiPhy moderwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.6
slavePhyNumProvides the slave number for this device (board) in the UTOPIA system bus (Applies to slave mode only)rwobsolete
INTEGER (-1..31)
.1.3.6.1.4.1.5003.9.10.1.1.7.7
utopiaBus16UTOPIA interface mode of bus widthrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.8
aTMPHYTypeExternal interface type of the boardrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.9
disablePayloadScramblingDisable/Enable Cell payload scrambling in the ATM PHYrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.10
pHYClkSourceOC3 Tx clock sourcerwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.11
sendIdleCASUponLinkFailThis I.366.2 allows sending a special idle CAS packet which signals that the other side has a failurerwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.12
masterSlaveModeLoop Emulation Mode (vmoa145) Master/Slave moderwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.13
vccProfileDetermine the required combination of Board's maximal number of VCC and maximal number of channels per VCCrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.7.14
tPNCPVPIVPI used for transferring TPNCP command over AAL5 transport layerrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.15
tPNCPVCIVCI used for transferring TPNCP command over AAL5 transport layerrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.16
sAALLink0VPIVPI of the 1st SAAL link (number 0)rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.17
sAALLink0VCIVCI of the 1st SAAL link (number 0)rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.18
sAALLink1VPIVPI of the 2nd SAAL link (number 1)rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.19
sAALLink1VCIVCI of the 1st SAAL link (number 1)rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.7.20
acSS7Settings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.8
acSS7SettingsTableobsolete
SEQUENCE OF AcSS7SettingsEntry
.1.3.6.1.4.1.5003.9.10.1.1.8.1
acSS7SettingsEntryobsolete
AcSS7SettingsEntry
.1.3.6.1.4.1.5003.9.10.1.1.8.1.1
acSS7LinkIdSS7 Link Id.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.8.1.1.1
acSS7traceLevel.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.8.1.1.2
acConfigFiles
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.11
acFxsCoefficientsThe FXS coefficient file name.roobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.11.1
acFxoCoefficientsThe FXO coefficient file name.roobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.11.2
acCptFile.roobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.11.3
acVpFileThe name (and path) of the file containing the voice promptsroobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.11.4
acCasTables
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.11.21
acCasTablesTableobsolete
SEQUENCE OF AcCasTablesEntry
.1.3.6.1.4.1.5003.9.10.1.1.11.21.1
acCasTablesEntryobsolete
AcCasTablesEntry
.1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1
acCasTableIndexCas Table Indexdroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1.1
acCasTabeNameCas Table Nameroobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.11.21.1.1.2
acFxs
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.12
acPolarityReversalTypeSets the type of the polarity reversal signal used for the network far-end answer and disconnect indications. Smooth reversal prevents negative effects as non-required ringing.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.12.1
megacoSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.13
megacoCurrentProfileUse this parameter to MGCP/MEGACO beheviour for specific compatibility. See user manual.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.13.1
megacoGatewayNameMGCP:Gateway's identification name towards the MGCP Call Agent. If empty Gateway name holds the IP address of the board MEGACO: Prefix of the gateway part of the termination namerwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.13.2
megacoEndpointNameMegaco Endpoint Namerwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.13.3
megacoTrunkNameMGCP: Together with 'EndpointPrefix' field generates local endpoint name on trunk enabled gateways MEGACO: Prefix of the trunk part of the termination namerwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.13.4
megacoActiveCallAgentIpMegaco Active Call Agentroobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.13.5
megacoActiveCallAgentPortMegaco Active Portroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.13.6
megacoCallAgents
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.13.7
megacoCallAgentsTableMagaco Call agents Tableobsolete
SEQUENCE OF MegacoCallAgentsEntry
.1.3.6.1.4.1.5003.9.10.1.1.13.7.1
megacoCallAgentsEntryobsolete
MegacoCallAgentsEntry
.1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1
megacoCallAgentIdMegaco Call Agent Idroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.1
megacoCallAgentIpMegaco CallAgent IPrwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.2
megacoCallAgentPortList of up to 10 UDP Ports of MEGACO Call Agent separated by , or ;.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.3
megacoCallAgentIsUsedIs this index usedrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.13.7.1.1.4
megacoCheckLegalityOfMGCThis parameter specified if the MEGACO will reject commands from an MGC not in the provisioned listrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.13.8
acPSTNParameters
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.14
acQ931RELAYMODEISDN level 3 moderwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.14.1
acIsdnDuplicateQ931BuffModeActivates / de-activates delivery of raw Q.931 messages. This Object is obsolete and is replaces by acTrunkISDNCommonDuplicateQ931BuffMode in the acPSTN-MIB.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.14.2
acPSTNCASTableNumIndicates how many CAS protocol configuration files are loaded, when 0 is no CAS table. It should match the number of fields.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.14.3
aMsConfiguration
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.51
amsNumOfConferencePortsNumber Of Conference ports. How many ports on the TPM are allocated to the conferencing service.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.51.1
amsNumOfTestTrunkPortsNumber Of Test Trunk ports. How many ports on the TPM are allocated to the Test Trunk service.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.51.2
amsNumOfLawfulInterceptPortsNumber Of Test Trunk ports. How many ports on the TPM are allocated to the Lawful Intercept service.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.51.3
amsNumOfAnnouncementPortsNumber Of Test Trunk ports. How many ports on the TPM are allocated to the Announcement service.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.51.4
amsApsIpAddressSets the destination IP to which the heartbeat packets are sent.rwobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.1.51.5
amsApsPortSets the destination UDP port to which the heartbeat packets are sent.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.51.6
amsPrimaryLanguagePrimary Languagerwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.51.7
amsSecondaryLanguageSecondary Languagerwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.51.8
amsProfileAMS Profile Bit Mask: 1'st bit - APS Audio Enable/Disable 2'nd bit - Trunks Interface On/Off 3'td bit - Board Operation State change on ATM Port failure Enable/Disable.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.1.51.9
amsAASPackagesProfile.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.1.51.10
acFeatureKey
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.90
acFeatureKeyStringCoded Key specific for board and required features.rwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.90.1
acActiveFeaturesListList of all avtivated features.roobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.90.2
supplementary
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.1.99
supplementaryFieldFlexible INI file line.rwobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.1.99.1
boardInformation
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.2
boardTypeThe type of the Board.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.2.1
boardNameThe name fo the boardroobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.2.2
serialNumserial number of board.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.3
dSPCountDSP Countroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.4
channelsCountChannel Count.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.5
cPUSpeedCPU Speedroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.6
softwareVersionTrunkPack Software Versionroobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.2.7
trunkPackSoftwareDateTrunkPack Software Dateroobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.2.8
slotNumberSlot numberroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.9
iniFileVersionIni file version.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.10
acDspTypeDsp Typeroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.11
acFlashVersionFlash [BootLoader] Version.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.12
acBoardFxsOrFxoBoard is Fxs Or Fxoroobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.2.13
acTrunkslCountTrunks Count.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.14
acDspVersionTemplateselects the DSP load number, which defines the supported set of coders. Default=0 Each template assigns a specific version to each DSP. Each DSP version supports a set of coders and features. The number of channels supported by the DSP can also vary between DSP versions. The total number of channels supported by the board depends on the selected template.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.15
acFirstPortDuplexModefull-duplex or half-duplex connectionroobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.2.16
acFirstPortSpeed.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.2.17
acMeanFreeChannelsMean of Free Channelsroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.18
acMaxFreeChannelsMax of Free Channelsroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.19
acSysUpTimeTime (in Seconds) that the board is alive.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.20
acPhysicalModCount.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.2.21
acBoardTemperatureTemperature of the board in degrees Celsius, should not go higher then 60!roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.2.22
channelConfiguration
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.3
voiceSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.3.2
voiceSettingsTableData in voice SettingsTable uniquely identify a voice parameters of channel.obsolete
SEQUENCE OF VoiceSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.2.1
voiceSettingsEntryobsolete
VoiceSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1
cIDChannel IDrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.1
coderDigital voice coderrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.2
eCEEnable/Disable Echo Cancelerrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.3
sCEEnable/Disable Silence Compresion mechanismrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.4
pFEPost Filter Enable of the voice coderrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.5
hPFEHigh Pass Filter Enabled of the voice coderrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.6
testModeTesting mode to be applied. Valid Range:CoderLoopback will perform an encoder-decoder loopback inside the DSP device, PCMLoopback will loopback the incoming PCM to the outgoing PCM, ToneInjection will generate a1000 Hz tone to outgoing PCM and NoLoopback will set the channel to work in a normal mode. Refer to TTestCode enumeration (default =3= NoLoopBack).rodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.7
voiceVolumeVoice Volume sets the voice decoder's output gain Range: 0-63 corresponding to -31 dB to +31 dB in 1 dB stepsrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.8
inputGainPCM input gain sets the gain at the encoder's input.rodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.9
mThis Packet Multiply Factor is the Number of 20 msec payloads (30 msec for G.723) to be used for generating one RTP packet. Range: 1 - Until max Tx/Rx buffer size is reachedrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.10
rTPRedundancyDepthRTP Redundancy Depth. Number of repetitions to be applied to each RTP payload when transmitting to network. apply redundancy sequence per RFC2198. Valid range: Disable redundancy packets generation = 0. Enable generation of RFC2198 redundancy packets = 1.rodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.11
eCLengthLength of echo canceler tail to be used according to TECLength enumeration. Note that EC length has different length limitations for different boards.rodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.12
eCHybridLossEcho Cancler Hybrid Loss. sets the worst case ratio between the signal level transmitted to the hybrid and the echo level returning from the hybrid. User should set this value according to the worst hybrid in the system in terms of echo return loss according to enum TECHybridLoss enumerationrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.2.1.1.13
faxModemSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.3.3
faxModemSettingsTableData in faxModem Settings Table uniquely identify fax and modem parameters channel.obsolete
SEQUENCE OF FaxModemSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.3.1
faxModemSettingsEntryobsolete
FaxModemSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1
fAXTransportTypeFAX Transport Type.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.1
acCallerIDTypeCallerID Type.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.2
v21ModemTransportTypeV21 Modem Transpor tType.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.3
v22ModemTransportTypeV22 Modem Transpor tType.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.4
v23ModemTransportTypeV23 Modem Transpor tType.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.5
v32ModemTransportTypeV32 Modem Transpor tType.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.6
v34ModemTransportTypeV34 Modem Transpor tType.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.7
faxRelayMaxRateFax Relay Max Rate Limits the maximum rate at which fax messages are transmitted. Refer to acTFaxModemRelayRate enumeration. (Default =14400 bps).roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.8
modemRelayMaxRateModem Relay Max Rate Limits the maximum rate at which modem relay messages are transmitted. Refer to acTFaxModemRelayRate enumeration. (Default =14400 bps).roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.9
faxRelayECMEnableFax Relay ECM Enable Enable using ECM mode during Fax Relay.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.10
t38FaxRelayProtectionModeT38 Fax Relay Protection Mode Use Forward Error Correction (FEC) algorithm to protect T.38 fax relay stream.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.11
faxRelayRedundancyDepthFax Relay Redundancy Depth Number of repetitions to be applied to each fax relay payload when transmitting to network (applicable only when acTFaxModemCmdacTFaxModemSettings.T38FaxRelayProtectionMode=0).roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.12
enhancedFaxRelayRedundancyDepthEnhanced Fax Relay Redundancy Depth Number of repetitions to be applied to control packets when using T.38 standard.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.13
modemRelayRedundancyDepthModem Relay Redundancy Depth Number of repetitions to be applied to each modem relay payload when transmitting to network.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.14
faxModemRelayVolumeFax Modem Relay Volume Fax gain control. Range: -18 - 15 corresponding to -18.5 dBm to -3.5 dBm in 1 dB steps. The reason the range extends to 15 is for backward compatibility. (Default =6).roobsolete
INTEGER (-18..15)
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.15
faxModemBypassCoderTypeFax Modem Bypass Coder Type Coder to be used while performing fax/modem bypass. Usually, high bit rate coders such as G.711 and G.726/G.727 should be used. (Default = G.711 A-law).roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.16
faxModemBypassMFax Modem Bypass M Number of 20 msec payloads to be used for generating one RTP fax/modem bypass packet. Range: 1 - Until max Tx/Rx buffer size is reachedroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.17
useT38orFRF11Use T38 or FRF11 Use T.38 protocol or proprietary FRF.11 syntax, to send/receive fax relay.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.3.1.1.18
dJBSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.3.4
dJBSettingsTableData in dJB Settings Table uniquely identify jitter buffer parameters of channel.obsolete
SEQUENCE OF DJBSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.4.1
dJBSettingsEntryobsolete
DJBSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.4.1.1
dJBufMinDelay[Millisec] Dynamic Jitter Buffer Minimum Delay. 0 - 150 (default =150)roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.4.1.1.1
dJBufOptFactorDynamic Jitter Buffer Optimization Factor. Dynamic jitter buffer frame error/delay optimization. 0 - 12 (default =7)roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.4.1.1.2
channelTDMBusSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.3.5
channelTDMBusSettingsTableData in channel TDM Bus Settings Table, uniquely identify TDM Bus sparameters of channelobsolete
SEQUENCE OF ChannelTDMBusSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.5.1
channelTDMBusSettingsEntryobsolete
ChannelTDMBusSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.5.1.1
tDMBusInputPortTDM Bus Input Port. Together with TDMBusInputChannel, defines the TDM bus timeslot to be used as input for this channel. Note that the valid region for this parameter varies according to the type of TDM bus used. When using TDMBusType=acFramers this parameter selects the trunkID, in which the incoming B-channel resides. 0-127.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.5.1.1.1
tDMBusInputChannelTDM Bus Input Channel. Together with TDMBusInputPort, defines the TDM bus timeslot to be used as input for this channel. Note that the valid region for this parameter varies according to the TDMBusSpeed. When using TDMBusType=acFramers, this parameter selects the incoming B-channel (in this case the valid region is 0-31).roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.5.1.1.2
tDMBusOutputDisableTDM Bus Output Disable. 0: Places TDM bus output timeslot in tri-state mode. Ignored in case of PSTN interface. 1: Enables TDM bus output timeslot. Ignored in case of PSTN interface.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.3.5.1.1.3
tDMBusOutputPortTDM Bus Output Port. Together with TDMBusOutputChannel, defines the TDM bus timeslot to be used as output for this channel. Note that the valid region for this parameter varies according to the type of TDM bus used. When this parameter is set to 0xff=255 the boardwise setting (set in acOpenBoard()) will be used. When using TDMBusType=acFramers, this parameter is ignored. 0-31 or 255.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.5.1.1.4
tDMBusOutputChannelTDM Bus Output Channel. Together with TDMBusOutputPort, defines the TDM bus timeslot to be used as output for this channel. Note that the valid region for this parameter varies according to the TDMBusSpeed. When using TDMBusType=acFramers, this parameter is ignored.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.5.1.1.5
transportSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.3.6
transportSettingsTableData in Transport Table, uniquely identify Transport sparameters of channel.obsolete
SEQUENCE OF TransportSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.6.1
transportSettingsEntryobsolete
TransportSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.6.1.1
useNIorPCIDescription: Use NI or PCI interface. =1 if channel will use NI interface, =0 if PCI interface. 0- PCI interface: Compressed traffic will be sent/received through the PCI interface. 1- NI interface: RTP-RTCP packets sent/received to/from on board Ethernet interface. (default=1).roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.6.1.1.1
disableSoftIPLoopbackDisable Soft IP Loopback =1 in order to diable soft IP loopback. 0- Enables the hair pin connection made in case two channels on the same board are connected together. 1- Disables the hair pin connection made in case two channels on the same board are connected together.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.6.1.1.2
uniDirectionalRTPuni Directional RTP. enables one sided RTP stream - according to niDirectionalRTPMode. enables the User to set the channel to work with unidirectional RTP streams. When UniDirectionalRTP is set to acRTPTxOnly, the receiver part of the channel will be disabled, and only the transmitter (encoder) will work. When UniDirectionalRTP is set to acRTPRxOnly, the transmitter part of the channel will be disabled, and only the receiver (decoder) will work. When UniDirectionalRTP is set to acRTPTxRx, both sides will be enabled. Users should note that when configuring a session between two endpoints, some of the channel configuration parameters must be identical on both sides. Such parameters are the voice coder type, the Fax/Modem transport type and bypass coders. All other configuration parameters are independent.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.6.1.1.3
rTPRTCPSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.3.7
rTPRTCPSettingsTableData in RTP-RTCP Table, uniquely identify RTP-RTCP sparameters of channel.obsolete
SEQUENCE OF RTPRTCPSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.7.1
rTPRTCPSettingsEntryobsolete
RTPRTCPSettingsEntry
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1
cNAMERTP Canonical Name. Should be unique among all participants within one RTP session. Refer to RFC1890 for more information. Up to 255 characters string. (default ='ChX', X=CID).roobsolete
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.1
iPPrecedenceIP Precedence. Sets the value of the IP precedence field in the IP header for all the packets to be generated from this channel. Follow the acTIPPrecedence enumeration. Valid Range: 0-7 (default =0)roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.2
iPTOSiP Type Of Service. sets the value of the IP Type Of Service field in the IP header for all the packets to be generated from this channel. acNormalServiceTOS=0, acMinimizeMonetaryCostTOS=1, acMaximizeReliabilityTOS=2, acMaximizeThroughputTOS=4, acMinimizeDelayTOS=8 (Follow the acTIPTOS enumeration).roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.3
localRTPPortLocal RTP Port. Local UDP Port to be used for incoming RTP stream to this channel. This parameter also sets the local RTCP and local T.38 ports in offset of 1,2 from LocalRTPPort respectively. The local RTP port must be a number dividable by 10 and must reside within the following range BoardParams.BaseUDPPort-> BoardParams.BaseUDPPort +10*MAX_CID_NUM.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.4
remoteRTPAddrRemote RTP Addressroobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.5
remoteRTPPortIP/UDP Address of the remote endpoint RTP portroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.6
remoteT38Addrremote T38 Addressroobsolete
IpAddress
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.7
remoteT38PortIP/UDP Address of the remote endpoint T.38 portroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.8
rTCPMeanTxIntervalRTCP Mean Tx Interval. Mean interval [msec] between channel's RTCP reports.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.9
rxRTPPayloadTypeRx RTP Payload Type -1 = use the default coder RTP payload type for incoming voice packets. -2 = allow any RTP payload type for incoming packets. Otherwise, = sets the RTP payload type to be used for incoming voice packets (this will override the default RTP payload type defined for each coder). Valid Range: -1/-2 or any unoccupied RTPPT in the range 0-127 . (default =-1).roobsolete
INTEGER (-2..127)
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.10
txRTPPayloadTypeTx RTP Payload Type -1 = use the default coder RTP payload type for incoming voice packets. -2 = allow any RTP payload type for incoming packets. Otherwise, = sets the RTP payload type to be used for incoming voice packets (this will override the default RTP payload type defined for each coder). Valid Range: -1/-2 or any unoccupied RTPPT in the range 0-127. (default =-1).roobsolete
INTEGER (-2..127)
.1.3.6.1.4.1.5003.9.10.1.3.7.1.1.11
channelStatus
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.4
channelStatusTableData in voice SettingsTable uniquely identify a voice parameters of channel.obsolete
SEQUENCE OF ChannelStatusEntry
.1.3.6.1.4.1.5003.9.10.1.4.1
channelStatusEntryobsolete
ChannelStatusEntry
.1.3.6.1.4.1.5003.9.10.1.4.1.1
rTPActiveRTP Activerodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.4.1.1.1
bypassNICBypass NICrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.2
pendingIdlePending Idleroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.3
txSilencePeriodTx Silence Periodrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.4
rxSilencePeriodRx Silence Periodrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.5
txFaxModeTx Fax Moderodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.6
rxFaxModeRx Fax Moderodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.7
txDTMFPeriodTx DTMF Periodrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.8
rxDTMFPeriodRx DTMF Periodrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.9
packetsToDSPCntJitter Buffer Error Counterrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.10
jitterBufErrorCntJitter Buffer Forced Packet countroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.11
jitterBufForcedPacketLostJitter Buffer Forced Packet Lostroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.12
jitterBufForcedPacketAdditionJitter Buffer Forced Packet Additionroobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.13
jitterBufUnderRunCntJitter Buffer Under-Run Counterrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.14
jitterBufOverRunCntJitter Buffer Over-Run Counterrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.15
jitterBufAccumDelayJitter Buffer accumulation Delay. In packets.roobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.4.1.1.16
fXSorFXOreturns the type phisical type of endpointrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.4.1.1.17
channelHookStateChannel Hook Staterodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.4.1.1.18
notifications
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.5
reset
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.6
remoteResetremote Reset. To remote reset the board, set an integer value to this parameter. Note: Before Reset, The current boardConfiguration parameters will be burned to the board.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.6.1
acSetDefaultsTo set the default values, set an integer value to this parameterrwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.6.2
acgwAdminStateDetermines the gateway's operational state. 0 - locked: Shutdown the GW In the time frame set by acgwAdminStateLockControl 1 - shuttingDown: (read only) Graceful Shutdown is being carried out 2 - unlocked: GW is in service.rwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.6.3
acgwAdminStateLockControl(in sec) time left for the graceful shutdown to complete. -1 indicates unlimited time frame. 0 indicates immediate (forced) lock. Implementing the control requires setting acgwAdminState to locked.rwobsolete
INTEGER (-1..65535)
.1.3.6.1.4.1.5003.9.10.1.6.4
acSaveConfigToSystemThis will save all current configuration in the board onto the flash. Any digit will call on the function. NOTE: Do NOT save the configuration while voice is running - this will cause a delay.rwobsolete
INTEGER
.1.3.6.1.4.1.5003.9.10.1.6.5
acOperationalStateThe operational state of the gateway.roobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.6.6
remoteResetControlDetermine the remote reset action 1 - burn staged load image, if any, and config to flash, perform a reset, and load from flash 2 - perform a reset, and load from flash (staged load image, if any, and config is not burned to flash) 3 - perform a reset, and load from bootp/tftp (staged load image, if any, and config burn is not needed) * - an error is returned for any other value Note: The staged load image is an image of a cmp file that was previously loaded to a area in RAM via an HTTP uploadrwobsolete
Enumeration
.1.3.6.1.4.1.5003.9.10.1.6.7
acTrap
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.21
acBoardTrapGlobals
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.21.1
acBoardTrapGlobalsNametrap namerodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.21.1.1
acBoardTrapGlobalsTextualDescriptiontitle of traprodeprecated
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.21.1.2
acBoardTrapGlobalsSourceTrap Source - MG1/Shelf1/Board2/Trunk3rodeprecated
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.21.1.3
acBoardTrapGlobalsSeverityTrap Severityrodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.21.1.4
acBoardTrapGlobalsUniqIDTrap Uniq Id - generated by AcBoard and should be uniq for the entire EMSrodeprecated
INTEGER
.1.3.6.1.4.1.5003.9.10.1.21.1.5
acBoardTrapGlobalsTypeTrap type - ItuAlarmTyperodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.21.1.6
acBoardTrapGlobalsProbableCauseTrap probable cause - SnmpAlarmProbableCauserodeprecated
Enumeration
.1.3.6.1.4.1.5003.9.10.1.21.1.7
acBoardTrapGlobalsAdditionalInfo1Trap additional info global fieldrodeprecated
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.21.1.8
acBoardTrapGlobalsAdditionalInfo2Trap additional info global fieldrodeprecated
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.21.1.9
acBoardTrapGlobalsAdditionalInfo3Trap additional info global fieldrodeprecated
OCTET STRING
.1.3.6.1.4.1.5003.9.10.1.21.1.10
acBoardTrapGlobalsDateAndTimeDate and time that the trap was sent.rodeprecated
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.5003.9.10.1.21.1.11
acBoardTrapDefinitions
OBJECT IDENTIFIER
.1.3.6.1.4.1.5003.9.10.1.21.2
acBoardFatalErrorBoard fatal error
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.1
acBoardConfigurationErrorConfiguration Error
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.2
acBoardTemperatureAlarmTemperature Alarm. Turned on when temperature exceeds 60 degrees Celsius, and relaxes when temperature goes under 55 again.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.3
acBoardEvBoardStartedInitialization Ended
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.4
acBoardEvResettingBoardThe board start Reset process - following software reset
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.5
acFeatureKeyErrorFeature key related Error
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.6
acgwAdminStateChangeThe administrative state of the gate way has been changed to a new state.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.7
acBoardCallResourcesAlarmNo free channels available
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.8
acBoardControllerFailureAlarmThe GK/Proxy not found or registration failed. internal routing table may be used for routing
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.9
acBoardEthernetLinkAlarmEthernet Link is down or remote Ethernet link is down and board has no communication to any other host
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.10
acBoardOverloadAlarmOverload in one or some of the system's components
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.11
acActiveAlarmTableOverflowAn active alarm could not be placed in the active alarm table because the table is full. This alarm will not clear. Reboot is the only way to completely clear the Active Alarm table overflow problem. Any alarm raised at this state will not be Carrier Grade compatible. Therefore, Updates will not clear the alarm before changing the bindings and re-raising alarms. The History tables remain unaffected. All Alarms raised prior to overflow will remain Carrier Grade compatible. Other alarms, raised after this alarm was raised, that are placed in the Active Alarm table will be Carrier Grade compatible. (This is for when after the alarm was raised there were some clears, clearing alarms off the Active Alarm table).
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.12
acAtmPortAlarmATM Port Alarm
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.13
acAudioProvisioningAlarmThis alarm is raised if the Media Server is unable to provision its audio. This could be because the Audio Provisioning System (APS) is down or there is a network problem.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.14
acOperationalStateChangeThis alarm is raised if the operational state of the node goes to disabled. The alarm is cleared when the operational state of the node goes to enabled.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.15
acKeepAliveThis trap is the NAT Traversal keep alive trap. If the STUN application in the device detects a NAT then this trap will be sent out on a regular time laps - 9/10 of the acSysSTUNBindingLifeTime object. The AdditionalInfo1 varbind has the MAC address of the device. Note that all traps are sent out from the SNMP Port (usually 161).
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.16
acNATTraversalAlarmWhen the NAT placed in front a device is identified as a symmetric NAT - this alarm is raised. It is cleared when a non-symmetric NAT or no NAT replace the symmetric one.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.17
acEnhancedBITStatusThis trap is used to for the status of the BIT (Built In Test). The information in the trap contains board HW elements being tested and their status. The information is presented in the additional info fields.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.18
acSS7LinkStateChangeAlarmThis alarm is raised if the operational state of the SS7 link becomes XXXX. The alarm is cleared when the operational state of the link becomes XXXX.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.19
acSS7LinkInhibitStateChangeAlarmThis alarm is raised if the SS7 link becomes inhibited (local or remote). The alarm is cleared when the link becomes uninhibited - local AND remote. Note that this alarm will be raised for any change in the remote or local inhibition status.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.20
acSS7LinkBlockStateChangeAlarmThis alarm is raised if the SS7 link becomes blocked (local or remote). The alarm is cleared when the link becomes unblocked - local AND remote. Note that this alarm will be raised for any change in the remote or local blocking status.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.21
acSS7LinkCongestionStateChangeAlarmThis alarm is raised if the SS7 link becomes congested (local or remote). The alarm is cleared when the link becomes uncongested - local AND remote. Note that this alarm will be raised for any change in the remote or local congestion status.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.22
acSS7LinkSetStateChangeAlarmThis alarm is raised if the operational state of the SS7 linkset becomes BUSY. The alarm is cleared when the operational state of the linkset becomes IN-SERVICE or OFFLINE.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.23
acSS7RouteSetStateChangeAlarmThis alarm is raised if the operational state of the SS7 routeset becomes BUSY. The alarm is cleared when the operational state of the routeset becomes IN-SERVICE or OFFLINE.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.24
acSS7SNSetStateChangeAlarmThis alarm is raised if the operational state of the SS7 node becomes BUSY. The alarm is cleared when the operational state of the node becomes IN-SERVICE or OFFLINE.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.25
acSS7RedundancyAlarmRaised when the SS7 redundancy degregated. Cleared when all entities of redundancy are fully functional and in serveice.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.26
acPerformanceMonitoringThresholdCrossingThis log trap is sent out for every time the threshold of a Performance Monitored object is crossed. The severity field is 'indeterminate' when the crossing is above the threshold and 'cleared' when it goes back under the threshold. The 'source' varbind in the trap indicates the object for which the threshold is being crossed.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.27
acHTTPDownloadResultThis trap indicates the result of a recent file download (includes HTTP error code, if available).
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.28
acFanTrayAlarmThis alarm is raised when the fan tray is missing or some of the fans are faulty. If the fan tray is missing or more then X fans are faulty the severity will be Critical. If more then one and less the X fans are faulty the severity will be Major.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.29
acPowerSupplyAlarmThis alarm is raised when the HA (High Availability) feature is active and one of the power supply units is faulty.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.30
acPEMAlarmThis alarm is raised when the HA (High Availability) feature is active. The severity is critical if one of the PEM units is missing and major if the electric wire to one of the units is disconnected.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.31
acSAMissingAlarmThis alarm is raised when the SA module in the M3K MG is missing. Whenthere is no SAT there are no other chassis HW related alarms. Note - relevant only for M3K.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.32
acHASystemFaultAlarmThis alarm is raised when the HA (High Availability) feature is active and the system is NOT HA. Critical severity - 1.Wrong HW Configuration. 2. Redundant module is missing (not in slot). 3. The redundant module is non operable. Minor severity - waiting for redunadant to connect (after reset!).
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.33
acHASystemConfigMismatchAlarmThis alarm is raised when the HA (High Availability) feature is active and there has been a configuration change due to which the HA system may or may not be usable.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.34
acHASystemSwitchOverAlarmThis alarm is raised when the HA (High Availability) feature is active and there has been a switchover due to failure or reset in the active module.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.35
acUserInputAlarmThis Alarm is raised when the input dry contact is short circuited. Cleared when the circuit is reopened.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.36
acDChannelStatusThis non alarm trap is sent when establishment, re-establishment or release of LAPD link with its peer connection occurs. The trap will be sent out with one of the following in the textual description: D-channel synchronized D-channel not-synchronized
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.37
acSonetSectionLOFAlarmSONET section Loss of Frame alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.38
acSonetSectionLOSAlarmSONET section Loss of Signal alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.39
acSonetLineAISAlarmSONET Line AIS alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.40
acSonetLineRDIAlarmSONET Line RDI alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.41
acSonetIfHwFailureAlarmSONET or SDH medium Interface has failed.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.42
acHwFailureAlarmHW failure alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.43
acH248LostConnectionWithCAH248 lost connection with call agent
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.44
acDialPlanFileReplaceddial plan file replaced notification
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.45
acAnalogPortSPIOutOfServiceAnalog port out of service
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.46
acAnalogPortHighTemperatureAnalog Port High Temperature
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.47
acHitlessUpdateStatusNotification trap that is sent out at the beginning and the end of a Hitless SW update. Failure during the process will also instigate the trap. Relevant to HA systems only.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.48
acTrunksAlarmNearEndLOSLoss of signal at trunk's near end.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.49
acTrunksAlarmNearEndLOFLoss of frame at trunk's near end.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.50
acTrunksAlarmRcvAISReceived AIS from trunk's far end.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.51
acTrunksAlarmFarEndLOFLoss of frame at trunk's far end.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.52
acIPv6ErrorAlarmAlarm trap that is sent out for IPv6 related errors.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.53
acAMSProcedureResultAMS procedure related information
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.54
acWeakRedundancyThe system is in weak redundancy mode. Switch over is done with a reset to the board taking over.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.55
acTMInconsistentRemoteAndLocalPLLStatusInconsistent Remote And Local PLL Status
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.56
acTMReferenceStatusTiming manager reference status
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.57
acTMReferenceChangeTiming manager reference Change
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.58
acGWSASEmergencyModeAlarmThe alarm is raised when SAS enters the Emergency Mode and then cleared when SAS enters Normal Mode again.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.59
acV52InterfaceAlarmThe alarm is raised for v5.2 interface errors and alarms.{@}For a detailed list of the interfaces' alarms see the acV5InterfceTable.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.60
acSonetPathSTSLOPAlarmSonet Path STS LOP alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.61
acSonetPathSTSAISAlarmSonet Path STS AIS alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.62
acSonetPathSTSRDIAlarmSonet Path STS RDI alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.63
acSonetPathUnequippedAlarmSonet Path Unequipped alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.64
acSonetPathSignalLabelMismatchAlarmSonet Path Signal Label Mismatch alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.65
acDS3RAIAlarmDS3 RAI alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.66
acDS3AISAlarmDS3 AIS alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.67
acDS3LOFAlarmDS3 LOF alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.68
acDS3LOSAlarmDS3 LOS alarm.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.69
acSWUpgradeAlarmRaised for SW upgrade process errors.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.70
acNTPServerStatusAlarmNTP server status alarm. {@}Raised when the connection to the NTP server is lost. Cleared when the connection is reestablished. {@}Unset time (as a result of no connection to NTP server) may result with functionality degradation and failure in device.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.71
acThreeWayConferenceOutOfResourcesThree way conference out of resources.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.72
acSS7AliasPcStateChangeAlarmraised when the Alias PC is in BUSY state. Cleared when it is in In-Service state.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.73
acSS7UalGroupStateChangeAlarmRaised when the Ual Group Asp state is not ACTIVE. Cleared when it is Active.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.74
acLDAPLostConnectionRaised when there is no connection to the LDAP server.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.75
acAnalogPortGroundFaultOutOfServiceRaised when the MP500 FXS port is inactive due to ground fault.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.76
acSSHConnectionStatusThis trap indicates the result of a recent SSH connection attempt.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.77
acOCSPServerStatusAlarmraised when OCSP connection is not available.
NOTIFICATION-TYPE
.1.3.6.1.4.1.5003.9.10.1.21.2.0.78
AcBoard - SNMP MIB Reference | MIBs Explorer