XPRESS-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
731
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
731 total| Object Name |
|---|
gandalf OBJECT IDENTIFIER .1.3.6.1.4.1.64 |
RFC1155-SMI Unknown .1.3.6.1.4.1.64 |
gCardInstalledThis trap indicates that a card was physically
installed in the hub. The trap will include the
rCardID attribute that identifies which card was
installed. TRAP-TYPE .1.3.6.1.4.1.64.0.9000 |
gCardRemovedThis trap indicates that a card was physically
removed from the hub. The trap will include the
rCardID attribute that identifies which card was
removed. TRAP-TYPE .1.3.6.1.4.1.64.0.9001 |
gCardMismatchThis trap indicates that a card was physically
installed in a slot configured with a different
card type. The rCardID attribute identifying the
installed card and the rCardType attribute for
this card are going to be included with this trap. TRAP-TYPE .1.3.6.1.4.1.64.0.9002 |
gCardMismatchClearedThis trap indicates that the slot causing a Card
Mismatch was reconfigured with the proper card
type. The rCardID attribute and rCardType
attribute will be included with this trap. TRAP-TYPE .1.3.6.1.4.1.64.0.9003 |
gCardFaultyThis trap indicates that a card was found to be
faulty by the system. The rCardID
attribute will be included with the trap. The text
portion of the trap will identify the reason
the card was found to be faulty. TRAP-TYPE .1.3.6.1.4.1.64.0.9004 |
gCardFaultyClearedThis trap indicates that the slot causing a Card
Faulty is now functional again. The rCardID
identifying the slot will be included with the
trap. TRAP-TYPE .1.3.6.1.4.1.64.0.9005 |
gNvramFaultThis trap indicates that one of the data objects
stored in NVRAM failed a CRC test. This object
will then be reconfigured with its default
parameters. TRAP-TYPE .1.3.6.1.4.1.64.0.9006 |
gFiltDatabaseFullThis trap indicates that the number of entries in
the Filtering Database has reached the upper limit of the system's
storage capacity. TRAP-TYPE .1.3.6.1.4.1.64.0.9007 |
gRTCFaultThis trap indicates that the internal tests done by the operational code
on the Real Time Clock failed. TRAP-TYPE .1.3.6.1.4.1.64.0.9008 |
gLANTestFailureThis trap indicates that the internal tests done by the operational code
on the LAN interface failed. TRAP-TYPE .1.3.6.1.4.1.64.0.9009 |
gCallConnectedThe system just connected to remote LAN.
Included with this TRAP will be the rWANStatsIndex,
rWANStatsCardID, rWANStatsPortID, rWANStatsChanID and
rWANStatsRemLANID identifying which card, port,
channel, resource module connected and remote LAN
this call will use. TRAP-TYPE .1.3.6.1.4.1.64.0.9010 |
gCallDisconnectedThe system just disconnected from a remote LAN.
Included with this trap will be the
rWANStatsIndex, rWANStatsCardID, rWANStatsPortID,
rWANStatsChanID identifying which card, port and
channel, resource module connected were associated
with this WAN link. TRAP-TYPE .1.3.6.1.4.1.64.0.9011 |
gCallFailureThe system refused a connection. If the
system rSysTrapCall is set, the TRAP will be sent
to the TRAP communities. TRAP-TYPE .1.3.6.1.4.1.64.0.9012 |
gP1BackplaneThe system could not detect the presence
of a P1 backplane. TRAP-TYPE .1.3.6.1.4.1.64.0.9013 |
gDatabaseInvalidOn startup, the system found that the database
was a newer revision than the database. TRAP-TYPE .1.3.6.1.4.1.64.0.9014 |
gNetsyncGainThe system detected the presence of the NETSYNC
clock. TRAP-TYPE .1.3.6.1.4.1.64.0.9015 |
gNetsyncLossThe system detected the loss of the NETSYNC
clock. TRAP-TYPE .1.3.6.1.4.1.64.0.9016 |
gCompressionThe system detected that the compression
engine couldn't startup. The text description gives the
reason. TRAP-TYPE .1.3.6.1.4.1.64.0.9017 |
gSecurityThe system detected a security violation
when attempting to accept a call. TRAP-TYPE .1.3.6.1.4.1.64.0.9018 |
gInvalidISDNSwitchThe system detected that the I/O card
had a software image that wouldn't run with the ISDN switch
currently set for the card. TRAP-TYPE .1.3.6.1.4.1.64.0.9019 |
gXferSuccessfulThe system detected that the file transfer
was successful. TRAP-TYPE .1.3.6.1.4.1.64.0.9020 |
gXferFailedThe system detected that the file transfer
was not successful. TRAP-TYPE .1.3.6.1.4.1.64.0.9021 |
gCardOverLimitThe system detected that the maximum number of
channels allowed per system has been exceeded. TRAP-TYPE .1.3.6.1.4.1.64.0.9022 |
gLeasedLineFaultThe system detected that the connection on
a leased line has failed. A trap will be generated every
fifteen minutes until the connection is completed. TRAP-TYPE .1.3.6.1.4.1.64.0.9023 |
gDChanUpThe system detected that a D channel has been
successfully brought up. TRAP-TYPE .1.3.6.1.4.1.64.0.9024 |
gDChanDownThe system detected a that D channel has been
dropped. TRAP-TYPE .1.3.6.1.4.1.64.0.9025 |
gInvalidPortConfThe system detected that a port configuration
attribute has been configured incorrectly. TRAP-TYPE .1.3.6.1.4.1.64.0.9026 |
gCfgChangeNotAppliedThe system detected thath a configuration change
has not yet been applied. The specific card must be
restarted for the change to take affect. TRAP-TYPE .1.3.6.1.4.1.64.0.9027 |
gSoftwareLoadIsThe system detected a variant version of
software has been downloaded to an I/O card. TRAP-TYPE .1.3.6.1.4.1.64.0.9028 |
gDuplicateNetworkThe system detected a duplicate IPX network
number. TRAP-TYPE .1.3.6.1.4.1.64.0.9029 |
gSapTableFullThe system detected that the SAP table has
reached its 500th Static entry or 2100th Dynamic entry. TRAP-TYPE .1.3.6.1.4.1.64.0.9030 |
gAuditRecordsLostThis trap is generated whenever audit records have been lost. TRAP-TYPE .1.3.6.1.4.1.64.0.9031 |
gLongCallThis trap is generated whenever a call to a remote LAN has
been connected for longer than the Long Call period. TRAP-TYPE .1.3.6.1.4.1.64.0.9032 |
gDChanFaultyThis trap is generated whenever a D channel is unstable and
losses the DSL more than the set threshold allows. TRAP-TYPE .1.3.6.1.4.1.64.0.9033 |
gAddressMovedTooOftenThis trap is generated whenever a mac address moves from lan to
lan too often which can cause an unstable network. TRAP-TYPE .1.3.6.1.4.1.64.0.9034 |
gTestPresenceCallPassedThis trap is generated when a test presence call is successful,
that is the remote either rang or answered the call. TRAP-TYPE .1.3.6.1.4.1.64.0.9035 |
gTestPresenceCallFailedThis trap is generated when a test presence call failed. TRAP-TYPE .1.3.6.1.4.1.64.0.9036 |
gTestPresenceCallNotIssuedThis trap is generated when the system is unable to issue a
test presence call. This is not an indication that the intended
remote LAN is not functional, thus the call should be re-
attempted. TRAP-TYPE .1.3.6.1.4.1.64.0.9037 |
gCardStateChangedThis trap indicates that the state of a card has changed.
The rCardID identifying the slot will be included with the
trap and the rCardOpState indicating the new card state. TRAP-TYPE .1.3.6.1.4.1.64.0.9038 |
gHardwareMismatchThis trap indicates that the hardware that is present
is not the hardware that is expected. TRAP-TYPE .1.3.6.1.4.1.64.0.9039 |
gandalf-rlanisdn OBJECT IDENTIFIER .1.3.6.1.4.1.64.9 |
rlanSystemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.1 |
rSysNameTells you the name allocated to this system.rw DisplayString .1.3.6.1.4.1.64.9.1.1 |
rSysAdminStateSelect this option when you want the system to process
new calls. If you disable this option, the system
will not accept or generate new calls, but existing calls will
remain connected. NOTE: Disable during SAP learning mode.
Disabling or enabling call processing will not affect the LAN.rw Enumeration .1.3.6.1.4.1.64.9.1.2 |
rSysTransDelayEnter the maximum frame age (in tenths of a second).rw INTEGER .1.3.6.1.4.1.64.9.1.4 |
rSysCallTeardownSelect this option when you want the system
to tear down all currently active calls.rw Enumeration .1.3.6.1.4.1.64.9.1.6 |
rSysNVRAMDiagTells you whether the system has passed the NVRAM diagnostics.
If it failed, the read/write test passed, but at least one of the
NVRAM objects failed the startup checksum. If
it passed, all the NVRAM objects passed the startup checksum.ro Enumeration .1.3.6.1.4.1.64.9.1.7 |
rSysRTCDiagTells you whether the system's real-time clock
is reliable. If the real-time clock has failed the diagnostics, the
system is using inaccurate time and date information.ro Enumeration .1.3.6.1.4.1.64.9.1.8 |
rSysLANDiagTells you whether the 82596 LAN controller chip
passed or failed the LAN diagnostics.ro Enumeration .1.3.6.1.4.1.64.9.1.9 |
rSysPromRevTells you the revision number of
the boot PROM.ro DisplayString .1.3.6.1.4.1.64.9.1.10 |
rSysOpStateTells you whether the system is operational (enabled),
not operational (disabled) or faulty.ro Enumeration .1.3.6.1.4.1.64.9.1.11 |
rSysUpTimeTells you how long (in hundredths of a
second) the system has been
running since the last reset.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.1.12 |
rSysTotalRAMTells you how much RAM has been allocated to
the System Controller.ro INTEGER .1.3.6.1.4.1.64.9.1.13 |
rSysRSCSlotTells you the slot position of the RSC 9000 card
(System Controller) with respect to the P2 backplane.ro INTEGER .1.3.6.1.4.1.64.9.1.14 |
rSysCompressionAdminStateSelect this option when you want the system to use data compression.rw Enumeration .1.3.6.1.4.1.64.9.1.15 |
rSysCompressionOpStateTells you whether data compression for the system
is disabled, enabled, or faulty.ro Enumeration .1.3.6.1.4.1.64.9.1.16 |
rSysCLIDSecuritySelect this option when you want the system to use
CLID security.rw Enumeration .1.3.6.1.4.1.64.9.1.17 |
rSysCLIDEnforcedSelect this option when you want the system to
accept only incoming calls with a CLID.rw Enumeration .1.3.6.1.4.1.64.9.1.18 |
rSysIncomingMinBearerSelect the minimum bearer capability allowed during an
incoming call: 64 Kbps Unrestricted, 56 Kbps Digital, 3100 Hz Audio, or Speech.rw Enumeration .1.3.6.1.4.1.64.9.1.19 |
rSysRLANLearningAdminStateSelect this option when you want the system to learn
remote LANs that use the Gandalf proprietary link protocol
and configure them in the database. The system will not learn
remote LANs that use PPP as their WAN protocol. Any LANs
calling in while this attribute is enabled will be learned
and named with Learnt_lanx, where x is the index into the
remote LAN list. Most of the information will be taken
from a default remote LAN set up in the database.
NOTE: Security is at a minimum when this option is enabled.rw Enumeration .1.3.6.1.4.1.64.9.1.20 |
rSysDateAndTimeEnter the current date and time, using the format specified in RFC 1443.rw OCTET STRING .1.3.6.1.4.1.64.9.1.21 |
rSysResetSelect hardReset when you want the System Controller to reset.rw Enumeration .1.3.6.1.4.1.64.9.1.22 |
rSysPasswordEnter the system password for the system's embedded console.rw DisplayString .1.3.6.1.4.1.64.9.1.23 |
rSysHubTypeTells you the hub type for this system installation.ro Enumeration .1.3.6.1.4.1.64.9.1.24 |
rSysRscSoftwareRevTells you the software revision for the
System Controller.ro DisplayString .1.3.6.1.4.1.64.9.1.25 |
rSysRscHardwareRevTells you the hardware revision for the
System Controller.ro DisplayString .1.3.6.1.4.1.64.9.1.26 |
rSysCompressionSoftwareRevTells you the software revision for the
System-Controller compression card.ro DisplayString .1.3.6.1.4.1.64.9.1.27 |
rSysCompressionHardwareRevTells you the hardware revision for the
System-Controller compression card.ro DisplayString .1.3.6.1.4.1.64.9.1.28 |
rSysCompressionPromRevTells you the revision number of the boot PROM for
the System-Controller compression card.ro DisplayString .1.3.6.1.4.1.64.9.1.29 |
rSysLongCallThresholdEnter the threshold an active call must exceed (120 - 86340 seconds)
before the system generates a potential trap and event alarm.
The range is from 2 mins to 23hrs 59 mins. The setting is in seconds
so they are in increments of 60.rw INTEGER .1.3.6.1.4.1.64.9.1.30 |
rSysLongCallEventsSelect this option when you want the system to generate alarms to the event log
when a call to a remote LAN exceeds the call threshold
you've set (rSysLongCallThreshold).rw Enumeration .1.3.6.1.4.1.64.9.1.31 |
rSysP1BckPlSizeTells you the size of the P1 backplane that the system is
attached to.ro INTEGER .1.3.6.1.4.1.64.9.1.32 |
rSysRipForwardingSelect this option when you want the system to forward the rips
learned from its active remote LANs that are doing PPP IPCP.
These rips will be forwarded onto the local LAN when enabled.rw Enumeration .1.3.6.1.4.1.64.9.1.33 |
rSysOverDOSBSSelect this option when you want the system to override the DOSBS
(Data Over Speech Bearer Services), enabled at IO card ports.rw Enumeration .1.3.6.1.4.1.64.9.1.34 |
rSysARPProxySelect this option when you want the system to answer
ARP request on behalf of a remote address configuered on
the protocol list table.rw Enumeration .1.3.6.1.4.1.64.9.1.35 |
rSysIdByCLIDSelect this option when you want the system to identify
a caller from its Calling Line ID (CLID) before the call
is answered. This is useful when the remote is to be
called back, so the system will reject the call without
the caller being charged for the call.rw Enumeration .1.3.6.1.4.1.64.9.1.36 |
rSysDialBackHoldoffTime delay the system will observe between the time it determines
a dialback call is to be placed and the actual outgoing call
request. This allows the remote to turn around and be prepared
to receive the call back.rw INTEGER .1.3.6.1.4.1.64.9.1.37 |
rSysFailedCallRetryHoldoffPeriod of time after a failed outgoing call attempt the system will
ignore request to place a call to the same remote. In Japan,
this is used to meet regulatory approvals where no more than 2
failed calls can be placed in a 3 minute time span. Can also
be used with dialback to guarantee that the system will not retry
an outgoing call if the remote is due to call back. If a switch
type is changed to Japanese, then this value will be changed to
61 seconds if it set to a lower value. When a Japanese switch is
defined, the minimum acceptable value is 61 seconds.rw INTEGER .1.3.6.1.4.1.64.9.1.38 |
rSysCLIDBlacklistAfterAttemptsThe number of times that a CLID will be allowed to
fail until it is blacklisted. The default is one,
that is, the first time that a CLID fails, it will
be blacklisted. If set to 0, this feature is disabled.rw INTEGER .1.3.6.1.4.1.64.9.1.39 |
rlanCardGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.2 |
rlanCardTableLets you view and manage how the
system configures individual cards. SEQUENCE OF RlanCardEntry .1.3.6.1.4.1.64.9.2.1 |
rlanCardEntry RlanCardEntry .1.3.6.1.4.1.64.9.2.1.1 |
rCardIDTells you the position of a card (1-10) within the hub with respect to
the P2 backplane.ro INTEGER .1.3.6.1.4.1.64.9.2.1.1.1 |
rCardTypeSelect the card type for this particular card: mrm9430, bri9308,
xsm9516RS232V11, xsm9516RS232V35, pri9360DB15, pri9346DB15,
pri9330BNC, pri9330DB15, pri9323DB15, briU9308.rw Enumeration .1.3.6.1.4.1.64.9.2.1.1.2 |
rCardAdmstSelect this option when you want the system to accept and
generate new calls on a card. If you disable this option,
existing calls on the card will remain connected, but the system
will not accept or generate new calls on the card.
DEFAULT = selectedrw Enumeration .1.3.6.1.4.1.64.9.2.1.1.3 |
rCardStatusSpecify whether a card is online or offline.
NOTE: If a card is ONLINE and you set it to OFFLINE, all
calls on the card will be torn down.
DEFAULT = onlinerw Enumeration .1.3.6.1.4.1.64.9.2.1.1.4 |
rCardDiagTells you whether this card has passed or failed diagnostics.ro Enumeration .1.3.6.1.4.1.64.9.2.1.1.5 |
rCardOpStateTells you the operational state of a card, which can be one of:
OFFLINE - you've pressed the OFFLINE button on the card
or you've set the status of the card (rCardStatus)
to OFFLINE.
ONLINE - the card is functioning.
GONE - the card is not in its slot, but the slot is still
configured.
FAULTY - the link to the card has been lost, or the card is defective.
DETECTED - the card has been detected, but its link to
the System Controller has not yet been established.
WAITDOWNREQ - the System Controller is waiting for a Download Request to
come from the card.
DOWNLOADING - the System Controller is downloading the op code to the card.
WAITDOWNACK - the download has been completed, and the System Controller is
now waiting for an acknowledgement from the card.
WAITOPCODE - the card is currently starting up.
MISMATCH - the card does not match the definition for it that is stored
in the database.
CARDEMPTY - the card has been removed from the slot, which is no longer
configured.
CARDREJECTED - the card has been rejected because it caused the number of
channels to exceed the maximum allowed.ro Enumeration .1.3.6.1.4.1.64.9.2.1.1.6 |
rCardSWRevTells you the software revision for the card.ro DisplayString .1.3.6.1.4.1.64.9.2.1.1.7 |
rCardHWRevTells you the hardware revision for the card.ro DisplayString .1.3.6.1.4.1.64.9.2.1.1.8 |
rCardTotalRAMTells you how much RAM (in bytes) has been allocated to the card.ro INTEGER .1.3.6.1.4.1.64.9.2.1.1.9 |
rCardBRISwitchIf this is a BRI9308 card, select the BRI switch type you want it to use:
ni1, nt, attPointToPoint, attMultiPoint, net3, or other.
If you try to select a BRI switch type for card types other than BRI,
you'll see the following error message: noSuchName.
DEFAULT = ni 1rw Enumeration .1.3.6.1.4.1.64.9.2.1.1.10 |
rCardBootPromTells you the software revision id of the boot PROM for this card.ro DisplayString .1.3.6.1.4.1.64.9.2.1.1.11 |
rCardResetSelect hardReset to reset the card.
NOTE: The card must be offline to be reset.
DEFAULT = noResetrw Enumeration .1.3.6.1.4.1.64.9.2.1.1.12 |
rCardTearDownSelect this option when you want the system to disconnect
all active calls on the card.
DEFAULT = noTear Downrw Enumeration .1.3.6.1.4.1.64.9.2.1.1.13 |
rCardRowStatusThe current status of this entry. If the row status is
set to destroy(6), the card will be removed from the
database only if the card is offline (see the rCardStatus
attribute). If the card is not OFFLINE, a BAD_VALUE_ERROR
will be returned to the Manager.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.2.1.1.14 |
rCardPriActivateSetting this object to 1 will activate the
changes of a PRI card. A read from this object
will return a 0 for no action needed, or a 2 for
changes pending. 0 and 2 cannot be set.rw Enumeration .1.3.6.1.4.1.64.9.2.1.1.15 |
rlanDChanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.3 |
rlanDChanStatsTableThis table provides a management view of the
statistics specific to individual D Channels. The
port ID is the D-channel ID. SEQUENCE OF RlanDChanStatsEntry .1.3.6.1.4.1.64.9.3.1 |
rlanDChanStatsEntry RlanDChanStatsEntry .1.3.6.1.4.1.64.9.3.1.1 |
rDChanCardIDTells you the position of this card (from 1 to 10)
within the hub with respect to the P2 backplane.ro INTEGER .1.3.6.1.4.1.64.9.3.1.1.1 |
rDChanPortIDTells you the Port ID of this D Channel.ro INTEGER .1.3.6.1.4.1.64.9.3.1.1.2 |
rDChanStateTells you the administrative status of the Channel
or Modem on this I/O card.ro Enumeration .1.3.6.1.4.1.64.9.3.1.1.3 |
rDChanRxFramesTells you how many LAPD frames have been received on
this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.4 |
rDChanRxCRCErrsTells you how many LAPD frames with CRC errors have been
received on this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.5 |
rDChanRxOverErrsTells you how many frames have been received on this
D Channel but discarded because there was not enough memory
to store them.ro Counter .1.3.6.1.4.1.64.9.3.1.1.6 |
rDChanRxOverflowsTells you the how many LAPD frames with
overflow errors have been received on this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.7 |
rDChanRxAbortsTells you how many LAPD frames have been received on
this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.8 |
rDChanRxCallsTells you how many calls have been received on this
D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.9 |
rDChanTxFramesTells you the how many LAPD frames have been transmitted on
this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.10 |
rDChanTxUnderErrsTells you how many LAPD frames with underrun errors have been
transmitted on this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.11 |
rDChanTxCallsTells you the how many calls have been transmitted on this
D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.12 |
rDChanLostDSLsTells you how many DSL (digital subscriber loop link) losses
have occurred on this D Channel (i.e., how many ISDN
connections have been dropped).ro Counter .1.3.6.1.4.1.64.9.3.1.1.13 |
rDChanCollsTells you how many LAPD frames have collided on this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.14 |
rDChanFrameSlipsTells you how many LAPD frames have slipped on
this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.15 |
rDChanLinkFaultsTells you how many link faults (timeouts) have occurred on
this D Channel.ro Counter .1.3.6.1.4.1.64.9.3.1.1.16 |
rlanDChanConfigTableThis table provides a management view of the system
configuration specific to individual D-channels. The
port ID is nothing else than the D-channel ID. SEQUENCE OF RlanDChanConfigEntry .1.3.6.1.4.1.64.9.3.2 |
rlanDChanConfigEntry RlanDChanConfigEntry .1.3.6.1.4.1.64.9.3.2.1 |
rDChanStatusSpecify whether a port should be put OFFLINE
or ONLINE. Reading this object always returns online(2)
regardless of the card's current operational state.
If the port is ONLINE and the attribute is set OFFLINE,
all calls on this port will be torn down and the port will
be put in the OFFLINE state.
To set a port back to ONLINE, select ONLINE from the list of options.
DEFAULT = onlinerw Enumeration .1.3.6.1.4.1.64.9.3.2.1.1 |
rDChanFaultThresholdEnter the threshold (1-10000 seconds) that the number of port
faults must exceed before the port is taken offline and a potential
trap and event alarm is generated. A value of zero disables this function.
DEFAULT = 0rw INTEGER .1.3.6.1.4.1.64.9.3.2.1.2 |
rDChanDOSBSSelect this option to enable digital over speech bearer for BRI D-channels.rw Enumeration .1.3.6.1.4.1.64.9.3.2.1.3 |
rDChanBriNetSyncSelect whether to source the system clock
from this network connection.rw Enumeration .1.3.6.1.4.1.64.9.3.2.1.4 |
rlanChannelGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.4 |
rlanChannelConfigTableThis table provides a management view of the
system configuration generic parameters specific
to individual data-bearing channels (i.e., ISDN B Channels and XSM sync
channels, but NOT ISDN D Channels). SEQUENCE OF RlanChannelConfigEntry .1.3.6.1.4.1.64.9.4.2 |
rlanChannelConfigEntry RlanChannelConfigEntry .1.3.6.1.4.1.64.9.4.2.1 |
rChanCardIDTells you the position of this card within the hub with respect
to the P2 backplane.ro INTEGER .1.3.6.1.4.1.64.9.4.2.1.1 |
rChanPortIDTells you which port this channel
belongs to on this specific card.ro INTEGER .1.3.6.1.4.1.64.9.4.2.1.2 |
rChanIDTells you the channel ID within the port.ro INTEGER .1.3.6.1.4.1.64.9.4.2.1.3 |
rChanOpModeSelect the mode of operation for this channel,
which can be one of: Disabled, AnswerCallsOnly;
AnswerAndOriginateCalls; OriginateCallsOnly,
Leased (PRI port only).
If this channel belongs to a BRI port (but not a PRI port),
it will set the other B Channel on the BRI port as well,
even if this attribute is set for a unique B Channel.
A B Channel that belongs to a BRI port supports
only the first four values. A badValue error will
be returned if a SET request with a value of 'leased' is
received on a B Channel that belongs to a BRI port.
A B Channel that belongs to a PRI port supports all values
from 1 to 5.
A B Channel that belongs to a card of type pri9360DB15 or
pri9346DB15 supports all values.
NOTE: A leased PRI will support only a disabled or
leased mode.
All values from 1 to 5 are supported on XSM channels.
DEFAULT = AnswerAndOriginateCallsrw Enumeration .1.3.6.1.4.1.64.9.4.2.1.4 |
rChanChannelGroupEnter the index for the Channel group
this channel belongs to. Setting this value on any
channel updates all channels that belong to the
same port.
DEFAULT = 1rw INTEGER .1.3.6.1.4.1.64.9.4.2.1.5 |
rChanHuntGroupEnter the index for the Hunt group this channel
belongs to. Setting this value on any channel
updates all channels that belong to the same
port.
DEFAULT = 1rw INTEGER .1.3.6.1.4.1.64.9.4.2.1.6 |
rChanOtherChanTells you the corresponding channel that is used if a
resource module connection is up. If this is indexed
by a Resource Module it will return the ISDN channel
used or the Resource Module used if this is a BRI or
PRI/DUAL Pri.
Note: A return of 0 means that any active call does not
include a resource module. Also, there is the
possiblility of 64 channels on a card, therefore
to find the corresponding channel on numbers
returned that are greater than 64, use the
following logic:
channel is on card X / 64 and is channel X mod 64.ro INTEGER .1.3.6.1.4.1.64.9.4.2.1.7 |
rlanBriChanConfigTableThis table provides a management view of the
system configuration generic parameters specific
to Basic Rate ISDN B Channels. SEQUENCE OF RlanBriChanConfigEntry .1.3.6.1.4.1.64.9.4.3 |
rlanBriChanConfigEntry RlanBriChanConfigEntry .1.3.6.1.4.1.64.9.4.3.1 |
rBChanPhoneNumEnter the telephone number that this B Channel responds to.rw DisplayString .1.3.6.1.4.1.64.9.4.3.1.1 |
rBChanSPIDEnter the service-profile ID that the Central Office
is providing for the B Channel.rw DisplayString .1.3.6.1.4.1.64.9.4.3.1.2 |
rlanSerialChanConfigTableThis table provides a management view of the
system configuration parameters specific
to serial channels. SEQUENCE OF RlanSerialChanConfigEntry .1.3.6.1.4.1.64.9.4.4 |
rlanSerialChanConfigEntry RlanSerialChanConfigEntry .1.3.6.1.4.1.64.9.4.4.1 |
rChanCallCtrlSelect the call-setup/teardown signalling to be used with
the attached device, which can be one of:
controlSignal or v25bis.
If rChanOpMode is set to 'leased', this option is forced to
controlSignal (setting it to any other value will generate
a bad value error).
DEFAULT = v25bisrw Enumeration .1.3.6.1.4.1.64.9.4.4.1.1 |
rChanHoldOffEnter the time (in seconds) between a disconnect and the
channel's availability to support an outbound call.
DEFAULT = 10rw INTEGER .1.3.6.1.4.1.64.9.4.4.1.2 |
rChanCallSetupTOEnter the time (in seconds) for completing call setup that the
system allows before timing out.
DEFAULT = 30.rw INTEGER .1.3.6.1.4.1.64.9.4.4.1.3 |
rlanSyncChanStatsTableThis table provides a management view of the
generic statistics for individual, synchronous, data bearing
channels (e.g., PRI, BRI and XSM channels). SEQUENCE OF RlanSyncChanStatsEntry .1.3.6.1.4.1.64.9.4.5 |
rlanSyncChanStatsEntry RlanSyncChanStatsEntry .1.3.6.1.4.1.64.9.4.5.1 |
rSyncChanWANStatsIndexTells you the WAN link that's associated with
this channel. If this channel is not currently connected,
you'll see a value of -1.ro INTEGER .1.3.6.1.4.1.64.9.4.5.1.1 |
rSyncChanLinkStateTells you the status of the channel's
connection, which can be one of: linkDown,
LinkUp, or linkFaulty.ro Enumeration .1.3.6.1.4.1.64.9.4.5.1.2 |
rSyncChanRxFramesTells you how many HDLC frames this channel has received since
the last system reset.ro Counter .1.3.6.1.4.1.64.9.4.5.1.3 |
rSyncChanRxOctetsTells you how many octets this channel has received since the
last system reset.ro Counter .1.3.6.1.4.1.64.9.4.5.1.4 |
rSyncChanRxFrameErrsTells you how many HDLC frames this channel has detected but not
successfully received for one of the following reasons:
1) Rxed with Bad CRC
2) Rxed with Overrun errors
3) Rxed aborted framesro Counter .1.3.6.1.4.1.64.9.4.5.1.5 |
rSyncChanRxCRCErrsTells you how many HDLC frames this channel has
received but discarded because of a CRC mismatch.ro Counter .1.3.6.1.4.1.64.9.4.5.1.6 |
rSyncChanRxOverErrsTells you how many HDLC frames this channel has
received but discarded because there was not enough memory in
the system to store them.ro Counter .1.3.6.1.4.1.64.9.4.5.1.7 |
rSyncChanRxAbortsTells you how many HDLC frames this channel has
received but discarded because the frame had been aborted.ro Counter .1.3.6.1.4.1.64.9.4.5.1.8 |
rSyncChanRxShortFramesTells you how many HDLC frames this channel has
received that were shorter than 4 bytes in length.ro Counter .1.3.6.1.4.1.64.9.4.5.1.9 |
rSyncChanRxLongFramesTells you how many HDLC frames this channel has
received that were longer than 4096 bytes in length.ro Counter .1.3.6.1.4.1.64.9.4.5.1.10 |
rSyncChanTxFramesTells you how many HDLC frames have been
transmitted on this channel since the last system reset.ro Counter .1.3.6.1.4.1.64.9.4.5.1.11 |
rSyncChanTxOctetsTells you how many octets have been
transmitted on this channel since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.4.5.1.12 |
rSyncChanTxFrameErrsTells you how many HDLC frames this channel tried to
transmit unsuccessfully since the last system reset for
one of the following reasons:
1) TXed underrun
2) TXed aborted framesro Counter .1.3.6.1.4.1.64.9.4.5.1.13 |
rSyncChanTxUnderErrsTells you how many HDLC frames this channel
tried to transmit unsuccessfully since the last system reset
because there was not enough data in memory to transmit.ro Counter .1.3.6.1.4.1.64.9.4.5.1.14 |
rSyncChanTxAbortsTells you how many HDLC frames this channel
tried to transmit unsuccessfully since the last system reset
because the frame had been aborted.ro Counter .1.3.6.1.4.1.64.9.4.5.1.15 |
rSyncChanLinkFaultsTells you how many times the WAN protocol has failed since the
last system reset.ro Counter .1.3.6.1.4.1.64.9.4.5.1.16 |
rSyncChanResourceShortsTells you how many resource shortages this channel has experienced
since the last system reset.
A resource shortage is a condition that occurs when the
channel driver runs out of receive buffers.ro Counter .1.3.6.1.4.1.64.9.4.5.1.17 |
rSyncChanLastResultCodeTells you the result code from the last call on
this channel.ro INTEGER .1.3.6.1.4.1.64.9.4.5.1.18 |
rSyncChanConnectedPhnumThis is the phone number (or extension number) of the
connected party, i.e. at the far end of this B-channel.ro DisplayString .1.3.6.1.4.1.64.9.4.5.1.19 |
rSyncChanConnectedNameThis is the name of the connected party, i.e. at the
far end of this B-channel. This information is sometimes
passed over the signalling channel of the network when
a call is generated or received, and on these occasions
the information is captured and stored here.ro DisplayString .1.3.6.1.4.1.64.9.4.5.1.20 |
rlanIsdnBChanTableThis table provides a management view of the ISDN
statistics and configeration for individual B Channels. SEQUENCE OF RlanIsdnBChanEntry .1.3.6.1.4.1.64.9.4.6 |
rlanIsdnBChanEntry RlanIsdnBChanEntry .1.3.6.1.4.1.64.9.4.6.1 |
rIsdnBChanBearerTells you what bearer capability is used
for this B Channel.ro Enumeration .1.3.6.1.4.1.64.9.4.6.1.1 |
rIsdnBChanLlSpeedAllows configeration of the leased line speed
for this B Channel (only valid on leased lines).rw Enumeration .1.3.6.1.4.1.64.9.4.6.1.2 |
rlanSerialChanStatsTableThis table provides a management view of the
statistics for individual serial channels. SEQUENCE OF RlanSerialChanStatsEntry .1.3.6.1.4.1.64.9.4.7 |
rlanSerialChanStatsEntry RlanSerialChanStatsEntry .1.3.6.1.4.1.64.9.4.7.1 |
rSerialChanIfTypeTells you the type of physical interface
signalling that is used for the attached device, which can be one of:
invalidHW, rs232, v35,or v11.ro Enumeration .1.3.6.1.4.1.64.9.4.7.1.1 |
rSerialChanRoleTells you what role the device that's using this
channel is performing:
dte - the device is acting as data terminal equipment
dce - the device is acting as data circuit-terminating equipment.ro Enumeration .1.3.6.1.4.1.64.9.4.7.1.2 |
rSerialChanCtlSignalsTells you the control signal state at the interface, which is bit-
mapped as follows:
Bit RS232 V.35 V.11
0 RTS RTS CTRL
1 CTS CTS IND
2 DSR DSR n/a
3 DCD DCD n/a
4 DTR DTR n/a
5 RI n/a n/a
6 TM n/a n/a
7 LL n/a n/a
8 RL n/a n/a
9 n/a n/a n/a
10 n/a n/a n/a
NOTE: Bit zero (0) is the least significant bit.ro INTEGER .1.3.6.1.4.1.64.9.4.7.1.3 |
rSerialChanLoopBackTells you the type of loopback test the system is running.
NOTE: Applies only to rs232 channels.rodeprecated Enumeration .1.3.6.1.4.1.64.9.4.7.1.4 |
rSerialChanInConnectsTells you how many attempted inbound connects the
signalling protocol in effect for this
channel has detected since the last system reset.ro Counter .1.3.6.1.4.1.64.9.4.7.1.5 |
rSerialChanOutConnectsTells you how many outbound connects have been attempted on this
channel since the last system reset.ro Counter .1.3.6.1.4.1.64.9.4.7.1.6 |
rSerialChanOutConnectFailsTells you how many outbound connects attempted on this
channel were not successfully established since the last system reset.ro Counter .1.3.6.1.4.1.64.9.4.7.1.7 |
rChannelGroupIdUnusedThis object is used to identify a potentially unused index
that can be used as the rChannelGroupId instance when
creating new entries in the rlanChannelGroupTable. A returned
value of zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.4.8 |
rlanChannelGroupTableThis table provides a management view of the
system channel groups. SEQUENCE OF RlanChannelGroupEntry .1.3.6.1.4.1.64.9.4.9 |
rlanChannelGroupEntryThe first entry (rChannelGroupId value of one) corresponds
to the default entry. This entry cannot be modified or
deleted. RlanChannelGroupEntry .1.3.6.1.4.1.64.9.4.9.1 |
rChannelGroupIdTells you the unique identifier for this row.ro INTEGER .1.3.6.1.4.1.64.9.4.9.1.1 |
rChannelGroupNameTells you the name of this channel group. Channel group
names must be unique and are not case sensitive.
You cannot modify the default entry Default.rw DisplayString .1.3.6.1.4.1.64.9.4.9.1.2 |
rChannelGroupStatusTells you the current status of this entry. You cannot destroy
currently assigned channel groups or the
default entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.4.9.1.3 |
rlanChannelDiagnosticTableThis table is used to force connect or disconnect
a channel. SEQUENCE OF RlanChannelDiagnosticEntry .1.3.6.1.4.1.64.9.4.10 |
rlanChannelDiagnosticEntry RlanChannelDiagnosticEntry .1.3.6.1.4.1.64.9.4.10.1 |
rChanDiagRemLANIDTells you which remote LAN this channel is to connect to.
The remote LAN values are from 1 to 1000 but reading this
value will always return 0.rw INTEGER .1.3.6.1.4.1.64.9.4.10.1.1 |
rChanDiagForceTo tell the system to disconnect this channel,
select disconnect from the available settings.
When you select connect, the system will try to
connect this channel to the remote LAN indicated by
rChanDiagRemLANID.
NOTE: The configuration for the remote LAN
must be a member of this channel's channel group.
DEFAULT = statusQuorw Enumeration .1.3.6.1.4.1.64.9.4.10.1.2 |
rlanHuntGroupTableThis table provides a management view of
Hunt Groups. SEQUENCE OF RlanHuntGroupEntry .1.3.6.1.4.1.64.9.4.11 |
rlanHuntGroupEntry RlanHuntGroupEntry .1.3.6.1.4.1.64.9.4.11.1 |
rHuntGroupIndexTells you which hunt group you are configuring.
The hunt group values are from 1 to 16.ro INTEGER .1.3.6.1.4.1.64.9.4.11.1.1 |
rHuntGroupNameThe name of this Hunt Group.rw DisplayString .1.3.6.1.4.1.64.9.4.11.1.2 |
rHuntGroupPhoneNumThe Phone number of this hunt group. Only printable
characters are accepted.rw DisplayString .1.3.6.1.4.1.64.9.4.11.1.3 |
rHuntGroupRowStatusTells you the current status of this entry. The only
states valid for this object are createAndGo(4) and Destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.4.11.1.4 |
rlanPBXChanGroupTableThis table provides a management view of
PBX Channels. SEQUENCE OF RlanPBXChanGroupEntry .1.3.6.1.4.1.64.9.4.12 |
rlanPBXChanGroupEntry RlanPBXChanGroupEntry .1.3.6.1.4.1.64.9.4.12.1 |
rPBXChanExtensionNumberThe extension number of this PBX channelrw DisplayString .1.3.6.1.4.1.64.9.4.12.1.1 |
rPBXChanModuleTypeThe module type of this PBX channel.
Cannot be set to none(1),gandalfAnalogPhoneEnd(4)'
or gandalfAnalogSwitchEnd(5) .rw Enumeration .1.3.6.1.4.1.64.9.4.12.1.2 |
rPBXChanPhoneTypeThe phone type connected to this PBX channelrw Enumeration .1.3.6.1.4.1.64.9.4.12.1.3 |
rPBXChanEncodingThe type of PCM encoding for this PBX channelrw Enumeration .1.3.6.1.4.1.64.9.4.12.1.4 |
rPBXChanVpmModeThe mode of the Voice Processing Module.
The value of 1 is for information only and
cannot be set.rw Enumeration .1.3.6.1.4.1.64.9.4.12.1.5 |
rlanResourceModuleTableThis table provides a management view of the
parameters specific to Modem and PBX card channels
(i.e., Modems and PBX Ports). SEQUENCE OF RlanResourceModuleEntry .1.3.6.1.4.1.64.9.4.13 |
rlanResourceModuleEntry RlanResourceModuleEntry .1.3.6.1.4.1.64.9.4.13.1 |
rResourceModuleOfflineThe online state of a module. Setting offline will not
allow the module to go online. Setting online will enable
the module to send and receive calls.
Reading this object always returns online(2)
regardless of the modules's current operational state.rw Enumeration .1.3.6.1.4.1.64.9.4.13.1.1 |
rResourceModuleLinkstateThe current operational state of the resource module.ro Enumeration .1.3.6.1.4.1.64.9.4.13.1.2 |
rlanPBXChanNTStatsTableThis table provides a statistical view of
Norther Telecom type of PBX Channels. SEQUENCE OF RlanPBXChanNTStatsEntry .1.3.6.1.4.1.64.9.4.14 |
rlanPBXChanNTStatsEntry RlanPBXChanNTStatsEntry .1.3.6.1.4.1.64.9.4.14.1 |
rPBXChanNTVoiceTimingPacketsTells you how many Voice Timing Packets this
link has processed.ro Counter .1.3.6.1.4.1.64.9.4.14.1.1 |
rPBXChanNTSignalCrcErrTells you how many Signal Packets with
CRC errors this link has processed.ro Counter .1.3.6.1.4.1.64.9.4.14.1.2 |
rPBXChanNTInvalidAddressTells you how many packets that have V.42
address errors this link has processed.ro Counter .1.3.6.1.4.1.64.9.4.14.1.3 |
rPBXChanNTSignalRejectsTells you how many times a voice packet
is received before an initialization packet
is received.ro Counter .1.3.6.1.4.1.64.9.4.14.1.4 |
rPBXChanNTMaxRetryErrTells you how many times this link has
reached maximum retries.ro Counter .1.3.6.1.4.1.64.9.4.14.1.5 |
rPBXChanNTLostSyncErrTells you how many times this link has
received a voice packet when it shouldn't,
or sent a packet of one type and received
an unexpected type of response packet.ro Counter .1.3.6.1.4.1.64.9.4.14.1.6 |
rPBXChanNTNoDataSignalTells you how many No Data Signal
errors this link has processed.ro Counter .1.3.6.1.4.1.64.9.4.14.1.7 |
rPBXChanNTAckTimeoutTells you how many times a packet is
sent without receiveing an acknowledgement
packet.ro Counter .1.3.6.1.4.1.64.9.4.14.1.8 |
rPBXChanNTTransLockupThis counter is incremented for every packet
that fails to be removed from the transmit
buffer.
eg. SDS signal not received by the PBX
extender.ro Counter .1.3.6.1.4.1.64.9.4.14.1.9 |
rPBXChanNTReinitTriesTells you the number of reinitialization
attempts on this link.ro Counter .1.3.6.1.4.1.64.9.4.14.1.10 |
rPBXChanNTDiscFailsTells you the number of disconnect
failures this link has processed.ro Counter .1.3.6.1.4.1.64.9.4.14.1.11 |
rPBXChanNTRetransThis counter increments if there are
three retransmission attempts in a row.ro Counter .1.3.6.1.4.1.64.9.4.14.1.12 |
rPBXChanNTInternalDiscTells you how many times the PBX thinks
that the phone is lost. Only applies to
the central extender.ro Counter .1.3.6.1.4.1.64.9.4.14.1.13 |
rPBXChanNTFatalPanicsTells you how many fatal panics have
occured on this port.ro Counter .1.3.6.1.4.1.64.9.4.14.1.14 |
rPBXChanNTLinkIntegrityTells you how many link integrity problems
have occured on this port.ro Counter .1.3.6.1.4.1.64.9.4.14.1.15 |
rPBXChanNTRxFailsTells you how many failed incoming calls
have occured on this port.ro Counter .1.3.6.1.4.1.64.9.4.14.1.16 |
rPBXChanNTTxFailsTells you how many failed outgoing calls
have occured on this port.ro Counter .1.3.6.1.4.1.64.9.4.14.1.17 |
rPBXChanNTCallsRxTells you how many successful incoming calls
have occured on this port.ro Counter .1.3.6.1.4.1.64.9.4.14.1.18 |
rPBXChanNTCallsTxTells you how many successful outgoing calls
have occured on this port.ro Counter .1.3.6.1.4.1.64.9.4.14.1.19 |
rlanWANStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.5 |
rlanWANStatsTableThis table provides a management view of the
system configuration specific to individual WAN links. SEQUENCE OF RlanWANStatsEntry .1.3.6.1.4.1.64.9.5.1 |
rlanWANStatsEntry RlanWANStatsEntry .1.3.6.1.4.1.64.9.5.1.1 |
rWANStatsIndexTells you which one of the possible
128 WAN links the current statistics apply to.
This index is mapped to a specific channel.
To find out which WAN link to use, get the rChanWANStatsIndex
attribute from the channel group first.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.1 |
rWANStatsCardIDTells you which card this WAN link is
using to talk to the currently connected remote LAN.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.2 |
rWANStatsPortIDTells you which port this WAN link is
using to talk to the currently connected remote LAN.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.3 |
rWANStatsChanIDTells you which of the 61 possible channels
this WAN link is using to talk to the currently connected
remote LAN. The number of possible channels will vary depending on card
type. For example a BRI has 2 channels/port, a PRI can have
up to 61 channels/port (European CEPT) and an XSM has one
channel/port.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.4 |
rWANStatsRemLANIDTells you which remote LAN this WAN
link connects to, by providing the index to be used in the
rlanRemLANGroup.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.5 |
rWANStatsRemLANNameTells you which remote LAN this WAN
link connects to by providing the name of the remote LAN.ro DisplayString .1.3.6.1.4.1.64.9.5.1.1.6 |
rWANStatsRxFramesTells you how many HDLC frames this WAN
link received during the current call.ro Counter .1.3.6.1.4.1.64.9.5.1.1.7 |
rWANStatsRxOctetsTells you how many octets this WAN link received
during the current call.ro Counter .1.3.6.1.4.1.64.9.5.1.1.8 |
rWANStatsRxFrameErrsTells you how many HDLC frames this WAN link detected
but did not successfully receive during the current call
for one of the following reasons:
1) Rxed with Bad CRC
2) Rxed with Overrun errors
3) Rxed aborted framesro Counter .1.3.6.1.4.1.64.9.5.1.1.9 |
rWANStatsRxCRCErrsTells you how many HDLC frames this WAN link received but then discarded
because of a CRC mismatch during the current call.ro Counter .1.3.6.1.4.1.64.9.5.1.1.10 |
rWANStatsRxOverErrsTells you how many HDLC frames this WAN link received but then discarded
during the current call because there wasn't enough
memory in the system to store them.ro Counter .1.3.6.1.4.1.64.9.5.1.1.11 |
rWANStatsRxAbortsTells you how many HDLC frames this WANlink received but then discarded
during the current call because the frame had been aborted.ro Counter .1.3.6.1.4.1.64.9.5.1.1.12 |
rWANStatsRatioErrRxTells you the ratio of unsuccessfully received HDLC frames to
the number of frames that this WAN link detected during the current call.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.13 |
rWANStatsTxFramesTells you how many HDLC frames this WAN
link transmitted during the current call.ro Counter .1.3.6.1.4.1.64.9.5.1.1.14 |
rWANStatsTxOctetsTells you how many octets this WAN link transmitted
during the current call.ro Counter .1.3.6.1.4.1.64.9.5.1.1.15 |
rWANStatsTxFrameErrsTells you how many HDLC frames this WAN link tried to transmit
unsuccessfully during the current call for one of the following
reasons:
1) TXed underrun
2) TXed aborted framesro Counter .1.3.6.1.4.1.64.9.5.1.1.16 |
rWANStatsTxUnderErrsTells you how many HDLC frames this WAN link tried to transmit
unsuccessfully during the current call because there wasn't enough
data in memory to transmit.ro Counter .1.3.6.1.4.1.64.9.5.1.1.17 |
rWANStatsTxAbortsTells you how many HDLC frames this WAN link tried to transmit
unsuccessfully during the current call because the frame had been aborted.ro Counter .1.3.6.1.4.1.64.9.5.1.1.18 |
rWANStatsRatioErrTxTells you the ratio of unsuccessfully transmitted frames
to the number of attempted frame transmissions during the current call.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.19 |
rWANStatsDurationTells you how long (in hundredths of a second) the system
has accumulated statistics for this WAN link.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.5.1.1.20 |
rWANStatsChanSpeedTells you the current channel speed in bits per second.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.21 |
rWANStatsRemExtIDTells you which remote Extension this WAN
link connects to, by providing the index to
be used in the rlanRemExtGroup.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.22 |
rWANStatsRemExtNameTells you which remote Extension this WAN
link connects to by providing the name of
the remote Extension.ro DisplayString .1.3.6.1.4.1.64.9.5.1.1.23 |
rWANStatsRMCardIDTells you which Resource Module card
this WAN link is using to talk to the
currently connected remote.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.24 |
rWANStatsRMPortIDTells you which Resource Module port
this WAN link is using to talk to the
currently connected remote.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.25 |
rWANStatsRMChanIDTells you which Resource Module Channel
this WAN link is using to talk to the
currently connected remote.ro INTEGER .1.3.6.1.4.1.64.9.5.1.1.26 |
rlanWANStatsRMChanTableThis table provides a management view of the
RM channels associated with a call at any time. SEQUENCE OF RlanWANStatsRMChanEntry .1.3.6.1.4.1.64.9.5.2 |
rlanWANStatsRMChanEntry RlanWANStatsRMChanEntry .1.3.6.1.4.1.64.9.5.2.1 |
rWANStatsRMWanIndexTells you which one of the possible
160 real WAN links or 128 virtual the current statistics apply to.
This index is mapped to a specific channel.
To find out which WAN link to use, get the rChanWANStatsIndex
attribute from the channel group first.ro INTEGER .1.3.6.1.4.1.64.9.5.2.1.1 |
rWANStatsRMChanIndexGives the channel index for the particular channel in use
by the call.ro INTEGER .1.3.6.1.4.1.64.9.5.2.1.2 |
rWANStatsRMChanCardIDTells you which Resource Module card
this channel is on.ro INTEGER .1.3.6.1.4.1.64.9.5.2.1.3 |
rWANStatsRMChanPortIDTells you which Resource Module port
this channel is on.ro INTEGER .1.3.6.1.4.1.64.9.5.2.1.4 |
rWANStatsRMChanChanIDTells you which Resource Module Channel
this channel is on.ro INTEGER .1.3.6.1.4.1.64.9.5.2.1.5 |
rWANStatsRMChanConnectedPhnumThis is the phone number (or extension number) of the
connected party, i.e. at the far end of this B-channel.ro DisplayString .1.3.6.1.4.1.64.9.5.2.1.6 |
rWANStatsRMChanConnectedNameThis is the name of the connected party, i.e. at the
far end of this B-channel. This information is sometimes
passed over the signalling channel of the network when
a call is generated or received, and on these occasions
the information is captured and stored here.ro DisplayString .1.3.6.1.4.1.64.9.5.2.1.7 |
rlanWANSummationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.6 |
rWANSumRxFramesTells you how many frames the
system has received since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.1 |
rWANSumRxOctetsTells you how many octets the
system has received since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.2 |
rWANSumRxFrameErrsTells you how many HDLC frames the system
detected since the last reset, but did not successfully
receive for one of the following reasons:
1) Rxed with Bad CRC
2) Rxed with Overrun errors
3) Rxed aborted framesro Counter .1.3.6.1.4.1.64.9.6.3 |
rWANSumRxCRCErrsTells you how many HDLC frames with CRC mismatches the
system has received since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.4 |
rWANSumRxOverErrsTells you how many HDLC frames with overrun errors the
system has received since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.5 |
rWANSumRxAbortsTells you how many aborted HDLC frames the
system has received since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.6 |
rWANSumTxFramesTells you how many HDLC frames the
system has transmitted since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.7 |
rWANSumTxOctetsTells you how many octets the
system has transmitted since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.8 |
rWANSumTxFrameErrsTells you how many HDLC frames the system has
detected since the last reset that were not successfully
received for one of the following 2 reasons:
1) Txed with underrun errors
2) Txed aborted framesro Counter .1.3.6.1.4.1.64.9.6.9 |
rWANSumTxUnderErrsTells you how many HDLC frames with underrun errors the
system has transmitted since the last
reset.ro Counter .1.3.6.1.4.1.64.9.6.10 |
rWANSumTxAbortsTells you how many frames the
system has aborted during transmission
since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.11 |
rWANSumLinkFaultsTells you how many link fault errors have occurred
since the last reset.ro Counter .1.3.6.1.4.1.64.9.6.12 |
rlanRemLANGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.7 |
rRemLANIDUnusedThis object is used to identify a potentially unused index
to be used as the rRemLANID when creating new entries in the
rlanRemLANConfigTable. A returned value of zero indicates that
the table is full.ro INTEGER .1.3.6.1.4.1.64.9.7.2 |
rlanRemLANConfigTableThis table provides a management view of the
system configuration specific to individual Remote
LAN's. SEQUENCE OF RlanRemLANConfigEntry .1.3.6.1.4.1.64.9.7.3 |
rlanRemLANConfigEntryThe conceptual row at instance zero is used by the
RSC as the default remote LAN configuration.
The values defined for this entry are assigned to learned
LAN's when the system is in remote LAN learning mode
(rSysRLANLearningAdminState is enabled(2)). This entry is
also used to change the defaults chosen when manually
configuring a new remote LAN either through the embedded
console or via SNMP. RlanRemLANConfigEntry .1.3.6.1.4.1.64.9.7.3.1 |
rRemLANIDTells you the index of this remote LAN. A value of 0 indicates
the default remote-LAN configuration; that is, this entry is used
to determine the default parameters for remote LANs that are
dynamically learned.ro INTEGER .1.3.6.1.4.1.64.9.7.3.1.1 |
rRemLANNameEnter the name of the current remote LAN. The name can use
up to 16 characters but cannot contain spaces. The name
must also be unique. It cannot be LOCAL_LAN or begin with
LEARNT_LAN. The default entry (instance zero) cannot be
modified.rw DisplayString .1.3.6.1.4.1.64.9.7.3.1.2 |
rRemLANOpModeTells you the current operational mode of this remote LAN,
which can be one of:
1- disabled: the system will not accept calls from
this remote LAN or generate calls to this
remote LAN
2- answerCallsOnly: the system will only answer
calls from this remote LAN.
3- answerAndOriginateCalls: the system will accept and
generate calls from/to this
remote LAN.
4- originateCallsOnly: the system will only
generate calls to this Remote LAN.
DEFAULT = answerAndOriginateCallsrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.3 |
rRemLANOutMinBearerSelect the minimum bearer capability allowed during an
outgoing call to a remote LAN when using ISDN services:
64 Kbps Unrestricted, 56 Kbps Digital, 3100 Hz Audio.
DEFAULT = kbps64Unrestrictrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.4 |
rRemLANCompressionSelect the type of compression when you want this remote LAN
to use.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.5 |
rRemLANWanProtocolSelect the communications protocol you want
the system to use when establishing a call to this remote LAN. The table
rlanGandalfProtoConfigTable contains additional information
when this object is set to gandalfProprietary(1) otherwise
the rlanPppConfigTable is to be used when this object is
set to ppp(2).
NOTE: When you are changing or creating new remote LANs, rRemLANSerialNumber
or rRemLANPppSecret for the remote LAN must be present (depending on
the setting of the remote LAN) in the same SNMP message.
DEFAULT = gandalfProprietaryrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.6 |
rRemLANIdleTimeoutEnter how long (in seconds) the connection must be idle before the
system decides to disconnect the channel(s). If you enter a value of '0',
there is no idle time-out.
DEFAULT = 90rw INTEGER .1.3.6.1.4.1.64.9.7.3.1.7 |
rRemLANMaxChannelsEnter the maximum number of channels to be connected to a
remote LAN.rw INTEGER .1.3.6.1.4.1.64.9.7.3.1.8 |
rRemLANFloodingSpecify whether or not the system should allow flooding of unknown
destination unicast packets to the remote LAN or from this remote LAN
to other remote LANs.
DEFAULT = torw Enumeration .1.3.6.1.4.1.64.9.7.3.1.9 |
rRemLANMCastFwdSelect the multicast packet treatment to be used for this remote
LAN.
DEFAULT = bi-directionalrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.10 |
rRemLANBCastFwdSelect the broadcast packet treatment to be used for this remote LAN.
DEFAULT = bi-directionalrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.11 |
rRemLANCallForceTo tell the system to disconnect this remote LAN,
select disconnect from the list of available options.
When you select connect, the system will try to
connect to the remote LAN on an available channel as
specified in the rlanDestAddressConfigTable selection
parameters (i.e., channel group)
DEFAULT = statusQuo.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.12 |
rRemLANWatchdogSpoofingSelect this option when you want the
system to respond to watchdog query packets received from
the local LAN by this remote LAN.
DEFAULT = disabledrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.13 |
rRemLANSAPandRIPSpoofingFilteringSelect this option when you want the system to forward,
spoof or filter SAP/RIP requests to this remote LAN.
DEFAULT = disabledrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.14 |
rRemLANSAPGroupsA list of indexes into the rlanSAPGroupTable. A single octet
value of 1 indicates the 'All' SAP group (any
other octets with values will generate a bad value error).
Setting this object to an octet string length of zero deletes
all previous values and returns this object to its default.
If rRemLANSAPandRIPSpoofingFiltering is disabled, this attribute
will return a zero length string (attempts to set this attribute
to any non-zero length string will generate a bad value error).
DEFAULT = 2Hrw OCTET STRING .1.3.6.1.4.1.64.9.7.3.1.15 |
rRemLANStatusTells you the current status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.7.3.1.16 |
rRemLANAroundCornerSelect this option when you want this remote LAN
to receive data from another remote LAN.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.17 |
rRemLANPPPNcpTypesSelect the NCP layer that the system should use
when communcating with this remote LAN
DEFAULT = BCP and IPCPrw Enumeration .1.3.6.1.4.1.64.9.7.3.1.18 |
rRemLANHuntGroupIndicates the huntgroup used by this remote LAN.
1 indicates that no Hunt group is defined for this
RemLAN.rw INTEGER .1.3.6.1.4.1.64.9.7.3.1.19 |
rRemLANMdmAnswerSelect this option when you want this modem to
originate or answer.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.20 |
rRemLANEncryptionSelect this option when you want to all data to be
encrypted/decrypted to/from this remote LAN.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.21 |
rRemLANSNASpoofingSelect this option when you want the system to spoof SNA
keepalive messages when all links to this remote LAN are
down. This feature is only available with the 'Point-of-
Sale' version.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.22 |
rRemLANDialBackSelect this option when you want the system to call right
back this remote LAN as soon as it is identified and
authenticated.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.23 |
rRemLANTestPresenceUse this option to trigger a test call to this remote LAN
using the supplied phone number. This will result in a trap,
either gTestPresenceCallPassed, gTestPresenceCallFailed or
gTestPresenceCallNotIssued, depending on the outcome of the call.
The phone number string can only contain digits and the letters
L (Local), N (National) and I (International) as a prefix
character. You cannot modify the default entry.rw DisplayString .1.3.6.1.4.1.64.9.7.3.1.24 |
rRemLANAllAtOnceIf enabled, once an outgoing call to this remote
LAN is required, Xpressway/XpressStack will attempt
to bring up the maximum number of channels configured
at the same time.rw Enumeration .1.3.6.1.4.1.64.9.7.3.1.25 |
rlanGandalfProtoConfigTableThis table contains objects that pertain to the management of
remote LANs that use the Gandalf proprietary link protocol. SEQUENCE OF RlanGandalfProtoConfigEntry .1.3.6.1.4.1.64.9.7.4 |
rlanGandalfProtoConfigEntryNo default entry at conceptual row zero exists in this table.
In short a default rRemLANSerialNumber cannot be used when
learning a remote LAN since this parameter is one of the few
parameters that is actually learnt during this process. RlanGandalfProtoConfigEntry .1.3.6.1.4.1.64.9.7.4.1 |
rRemLANSerialNumberEnter the unique serial number of the remote LAN.rw OCTET STRING .1.3.6.1.4.1.64.9.7.4.1.1 |
rlanPppConfigTableThis table contains objects that pertain to the management of
remote LANs that use the PPP Internet standard link protocol. SEQUENCE OF RlanPppConfigEntry .1.3.6.1.4.1.64.9.7.5 |
rlanPppConfigEntryA default entry at conceptual row zero does exist in this
table. The default entry can be used to specify the PPP
authentication protocol only. RlanPppConfigEntry .1.3.6.1.4.1.64.9.7.5.1 |
rRemLANPppAuthSelect the authentication protocol
the system should use when verifying
the identification of the remote LAN.
DEFAULT = paprw Enumeration .1.3.6.1.4.1.64.9.7.5.1.1 |
rRemLANPppSecretTells you the PPP secret for the remote LAN. The PPP identity
is the name you entered for the remote LAN (rRemLANName). You cannot
modify the default entry.rw OCTET STRING .1.3.6.1.4.1.64.9.7.5.1.2 |
rRemLANPppNCPSelect the NCP layer that the system should use
when communcating with this remote LAN
DEFAULT = BCP and IPCPrw Enumeration .1.3.6.1.4.1.64.9.7.5.1.3 |
rRemLANRemIPAddrHandlingThis attribute determines wether the system can accept
or override the DNS IP address submitted by
a remote system. DEFAULT = accept.rw Enumeration .1.3.6.1.4.1.64.9.7.5.1.4 |
rRemLANPPPRemIPAddrThe IP address to assign to remote if rRemLANRemIPAddrHandling
is set to assign(3)rw IpAddress .1.3.6.1.4.1.64.9.7.5.1.5 |
rRemLANPPPBapHandlingThis attribute determines which BAP protocol is
used on a remote LAN PPP connection.
DEFAULT = bacp_and_mpplus.rw Enumeration .1.3.6.1.4.1.64.9.7.5.1.6 |
rlanDestAddressConfigTableThis table contains objects that pertain to the management of remote LAN addressing information. SEQUENCE OF RlanDestAddressConfigEntry .1.3.6.1.4.1.64.9.7.6 |
rlanDestAddressConfigEntryFor the default rRemLANID entry (conceptual row zero) two
defaults exist in this table. RlanDestAddressConfigEntry .1.3.6.1.4.1.64.9.7.6.1 |
rDestAddrIdTells you the unique identifier for this entry.ro INTEGER .1.3.6.1.4.1.64.9.7.6.1.1 |
rDestPrefixEnter an index (1 to 33) into the rlanAddressPrefixConfigTable.
DEFAULT = 1rw INTEGER .1.3.6.1.4.1.64.9.7.6.1.2 |
rDestPhoneNumEnter the address of this remote LAN (e.g., a phone number). The
phone number string can only contain digits and the letters
L (Local), N (National) and I (International) as a prefix
character. You cannot modify the default entry.rw DisplayString .1.3.6.1.4.1.64.9.7.6.1.3 |
rDestChannelGroupIdEnter an index (1 to 65) into the rlanChannelGroupTable.
The system uses the selected entry in this table to determine
which group of channels to use when it attempts to establish a
call to a remote LAN.
DEFAULT = 1rw INTEGER .1.3.6.1.4.1.64.9.7.6.1.4 |
rDestLANCLIDEnter the primary Calling Line IDentity number presented
during an incoming call from this Remote LAN. The CLID must
contain all 16 digits. You cannot modify the default entry.rw DisplayString .1.3.6.1.4.1.64.9.7.6.1.5 |
rDestLANMdmRequestSelect this option when you want to use a modem for this
remote LAN.rw Enumeration .1.3.6.1.4.1.64.9.7.6.1.6 |
rAddrPrefixIdUnusedThis object is used to identify a potentially unused index
that can be used as the rAddrPrefixId instance when
creating new entries in the rlanAddressPrefixConfigTable. A
returned value of zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.7.7 |
rlanAddressPrefixConfigTableThis table contains objects that pertain to the
management of destination address extension prefixes. SEQUENCE OF RlanAddressPrefixConfigEntry .1.3.6.1.4.1.64.9.7.8 |
rlanAddressPrefixConfigEntryThe first entry (rAddrPrefixId value of one) corresponds
to the default entry. This entry cannot be modified or
deleted. RlanAddressPrefixConfigEntry .1.3.6.1.4.1.64.9.7.8.1 |
rAddrPrefixIdTells you the prefix entry id.ro INTEGER .1.3.6.1.4.1.64.9.7.8.1.1 |
rAddrPrefixNameEnter the ASCII name that is associated with a prefix entry.
The name must be unique and is not case sensitive. You cannot
modify the default entry 'None'.rw DisplayString .1.3.6.1.4.1.64.9.7.8.1.2 |
rAddrPrefixStringEnter the prefix string that will precede the destination phone
number.rw OCTET STRING .1.3.6.1.4.1.64.9.7.8.1.3 |
rAddrPrefixStatusThe current status of this entry. Entries that are in use
(referenced by an entry in the rlanDestAddressConfigTable)
cannot be destroyed. The default entry cannot be destroyed.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.7.8.1.4 |
rlanRemLANStatsTableThis table provides a management view of the
system configuration specific to individual Remote
Lans. SEQUENCE OF RlanRemLANStatsEntry .1.3.6.1.4.1.64.9.7.9 |
rlanRemLANStatsEntry RlanRemLANStatsEntry .1.3.6.1.4.1.64.9.7.9.1 |
rRemLANWANStatsIndexThis string of octets is used to indicate active entries
in the rlanWANStatsTable entries where each octet represents
an index into this table. A null string length indicates that
this remote LAN is currently not active (up). If more than
one octet is returned then multi-linking is being performed.ro OCTET STRING .1.3.6.1.4.1.64.9.7.9.1.1 |
rRemLANLastBearerTells you which bearer capability was used for the last call to
this remote LAN. Connections to remote LANs that were made using
XSM channels are reported as xsm(6).ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.2 |
rRemLANLastFailTells you the failure code for the last call.ro INTEGER .1.3.6.1.4.1.64.9.7.9.1.3 |
rRemLANLastTimeTells you the number of TimeTicks that have
elapsed since the last connection to this remote LAN. This
value resets every time the remote LAN connects to the local
LAN. Returns a 0 if a connection has yet to be made.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.7.9.1.4 |
rRemLANInCompressedBitsTells you how many compressed bits have been
received from this remote LAN. The system uses this
information when calculating the inbound compression ratio.ro Counter .1.3.6.1.4.1.64.9.7.9.1.5 |
rRemLANInUncompressedBitsTells you how many uncompressed bits have been
received from this remote LAN. The system uses this
Information when calculating the inbound compression ratio.ro Counter .1.3.6.1.4.1.64.9.7.9.1.6 |
rRemLANInFramesTells you how many frames (both unicast and non-unicast)
have been received from this remote LAN
and forwarded to the local LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.7 |
rRemLANInUCastFwdsTells you how many unicast frames have been received from
this remote LAN and forwarded to the local LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.8 |
rRemLANInUCastFiltsTells you how many frames have been received from
this remote LAN and filtered out.ro Counter .1.3.6.1.4.1.64.9.7.9.1.9 |
rRemLANInMCastFwdsTells you many multicast frames have been received from
this remote LAN and forwarded to the local LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.10 |
rRemLANInMCastFiltsTells you how many multicast frames have been received from
the remote LAN and filtered out.ro Counter .1.3.6.1.4.1.64.9.7.9.1.11 |
rRemLANInBCastFwdsTells you how many broadcast frames have been received from
the remote LAN and forwarded to the local LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.12 |
rRemLANInBCastFiltsTells you how many frames have been received from
the remote LAN and filtered out.ro Counter .1.3.6.1.4.1.64.9.7.9.1.13 |
rRemLANOutCompressedBitsTells you how many compressed bits have been
forwarded to the remote LAN. The system uses this
information when calculating the outbound compression ratio.ro Counter .1.3.6.1.4.1.64.9.7.9.1.14 |
rRemLANOutUncompressedBitsTells you how many uncompressed bits have been
forwarded to the remote LAN. The system uses this
information when calculating the outbound compression ratio.ro Counter .1.3.6.1.4.1.64.9.7.9.1.15 |
rRemLANOutFramesTells you how many frames (both unicast and non-unicast)
have been forwarded to a WAN link
assigned to this remote LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.16 |
rRemLANOutUCastFwdsTells you how many unicast frames have been forwarded to a
WAN link assigned to this remote LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.17 |
rRemLANOutMCastFwdsTells you how many multicast frames have been received from
the local LAN and forwarded to the WAN link
assigned to this remote LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.18 |
rRemLANOutBCastFwdsTells you how many broadcast frames received from
the local LAN have been forwarded to the remote LAN.ro Counter .1.3.6.1.4.1.64.9.7.9.1.19 |
rRemLANDiscTransTells you how many frames were queued to be transmitted
but then discarded because their transit delay exceeded the
maximum limit.ro Counter .1.3.6.1.4.1.64.9.7.9.1.20 |
rRemLANResShortsTells you how many frames were queued to be transmitted
but then discarded because of an internal resource shortage.ro Counter .1.3.6.1.4.1.64.9.7.9.1.21 |
rRemLANDurationTells you how long this remote LAN has been connected
since the last system reset.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.7.9.1.22 |
rRemLANRemoteIPThe IP Address of the remote LAN .ro IpAddress .1.3.6.1.4.1.64.9.7.9.1.23 |
rRemLANCompressionResetsRxTells you how many compression resets we received from the
peer.ro Counter .1.3.6.1.4.1.64.9.7.9.1.24 |
rRemLANCompressionResetsTxTells you how many compression resets we sent to the peer.ro Counter .1.3.6.1.4.1.64.9.7.9.1.25 |
rRemLANLocalDecompressionTypeTells you which bearer capability was used for the last call to
this remote LAN. Connections to remote LANs that were made using
XSM channels are reported as xsm(6).ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.26 |
rRemLANLocalCompressionTypeTells you which bearer capability was used for the last call to
this remote LAN. Connections to remote LANs that were made using
XSM channels are reported as xsm(6).ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.27 |
rRemLANBcpStatusTell you if the BCP Network Control Protocol
(NCP) is active for this remote LAN.ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.28 |
rRemLANIpcpStatusTell you if the IPCP Network Control Protocol
(NCP) is active for this remote LAN.ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.29 |
rRemLANIpxcpStatusTell you if the IPXCP Network Control Protocol
(NCP) is active for this remote LAN.ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.30 |
rRemLANBacpStatusTell you if the PACP Protocol
is active for this remote LAN.ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.31 |
rRemLANMpplusStatusTell you if the Mpplus Protocol
is active for this remote LAN.ro Enumeration .1.3.6.1.4.1.64.9.7.9.1.32 |
rRemLANDynamicTell you if this remote LAN has been
created dynamicallyro Enumeration .1.3.6.1.4.1.64.9.7.9.1.33 |
rRemLANUserMustAuthenticateTell you if this remote LAN must
use authenticationro Enumeration .1.3.6.1.4.1.64.9.7.9.1.34 |
rRemLANLastConnectedASCII String of the last time this remote
has connected.ro DisplayString .1.3.6.1.4.1.64.9.7.9.1.35 |
rlanLocLANGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.8 |
rLocLANAdmstSelect the desired state of
the local LAN: disabled or enabled.rw Enumeration .1.3.6.1.4.1.64.9.8.1 |
rLocLANConnectorSelect the Ethernet interface for the local LAN depending
on the Hardware platform: for the 10095 and 8441 boards the
choices are AUI or P2. The 10444 boards cannot be changed.
NOTE: Changing the Ethernet interface may disconnect
any active connections with the system through the LAN port.rw Enumeration .1.3.6.1.4.1.64.9.8.2 |
rLocLANMACAddressTells you the MAC address of the local LAN.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.64.9.8.3 |
rLocLANOpStateTells you whether the local LAN is disabled, enabled, or faulty.ro Enumeration .1.3.6.1.4.1.64.9.8.4 |
rLocLANRxFramesTells you how many Ethernet frames have been received
from the local LAN since the last system reset.ro Counter .1.3.6.1.4.1.64.9.8.5 |
rLocLANRxOctetsTells you how many octets have been received
from the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.6 |
rLocLANRxAlignErrsTells you how many frames from the local LAN
have been lost during reception due to alignment errors
since the last system reset.ro Counter .1.3.6.1.4.1.64.9.8.7 |
rLocLANRxCRCErrsTells you how many frames
from the local LAN were lost during reception
due to CRC errors since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.8 |
rLocLANRxMCastsTells you how many multicast packets have
been received from the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.9 |
rLocLANRxBCastsTells you how many broadcast packets have
been received from the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.10 |
rLocLANTxFramesTells you how many frames have been transmitted
successfully to the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.11 |
rLocLANTxOctetsTells you how many octets have been transmitted
successfully to the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.12 |
rLocLANTxSingleCollsTells you how many frames have been lost due to single
collisions since the last system reset.ro Counter .1.3.6.1.4.1.64.9.8.13 |
rLocLANTxMultiCollsTells you how many frames from the local LAN
have been lost due to multiple
collisions since the last system reset.ro Counter .1.3.6.1.4.1.64.9.8.14 |
rLocLANTxErrsTells you how many frames from the local LAN
have been lost during reception due to CRC errors
and alignment errors since the last system reset.ro Counter .1.3.6.1.4.1.64.9.8.15 |
rLocLANLateCollsTells you how many frames from the local LAN
have been lost due to a late collision since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.16 |
rLocLANExcessCollsTells you how many frames this port has tried to
transmit unsuccessfully since the last
system reset because it was not
clear-to-send (CTS) or because the 82596 chip
locked and had to reset.ro Counter .1.3.6.1.4.1.64.9.8.17 |
rLocLANTxMCastsTells you how many multicast packets have been
transmitted to the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.18 |
rLocLANTxBCastsTells you how many broadcast packets have been
transmitted to the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.8.19 |
rLocLANResShortsTells you how many frames could not be
transmitted to the local LAN since the last
system reset due to a lack of memory or other resources.ro Counter .1.3.6.1.4.1.64.9.8.20 |
rLocLANCSErrsTells you how many frames could not be
transmitted to the local LAN since the last
system reset due to carrier sense errors.ro Counter .1.3.6.1.4.1.64.9.8.21 |
rLocLANProtocolFilterForwardSelect this if you want LAN Protocol Filtering/forwarding.rw Enumeration .1.3.6.1.4.1.64.9.8.22 |
rLocLANProtocolIDA list of indexes into the rlanLANProtocolIDTable. Indexes
122-127 are predefined entries in the table:
122 Novell IPX/SPX 8137
123 AppleTalk ARP 80F3
124 AppleTalk 809B
125 Reverse ARP 8035
126 ARP 0806
127 TCP/IP 0800
Indexes 1-121 are reserved for future predefined entry expansion.
Indexes 128 and up are user defined entries.
If rLocLANProtocolFilterForward is forwardall, this attribute
will return a zero length string (attempts to set this attribute
to any non-zero length string will generate a bad value error).rw OCTET STRING .1.3.6.1.4.1.64.9.8.23 |
rLocLANOperatingModeTells you the mode of operation that the RSC 9002
LAN controller has negociated. Only valid on the 9002
platform.ro Enumeration .1.3.6.1.4.1.64.9.8.24 |
rLocLANEthModeThis attribute selects the operational mode of the Ethernet physical interfaces.
It is only applicable to systems that support 100 Meg Ethernet. An error condition
will be returned if 100 Meg Ethernet is not supported.
1- autonegotiate: indicates that the interface will use the auto-negotiation feature
from the 802.3u standard to determine link speed.
2- 100baseT_fdx: forces the interface into 100baseTX full duplex mode.
3- 100baseT: forces the interface into 100baseTX mode.
4- 10baseT_fdx: forces the interface into 10baseT full duplex mode.
5- 10baseT: forces the interface into 10baseT mode.
DEFAULT = autonegotiaterw Enumeration .1.3.6.1.4.1.64.9.8.25 |
rlanLocLANFilterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.9 |
rLocLANFilterInFramesTells you how many frames (both unicast and non-unicast)
have been received from the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.9.1 |
rLocLANFilterInUCastsTells you how many valid unicast frames (filtered frames
plus forwarded frames) have been received
from the local LAN since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.9.2 |
rLocLANFilterInUCastFwdsTells you how many valid unicast frames have been received
from the local LAN and forwarded to the remote LAN
since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.3 |
rLocLANFilterInUCastFiltsTells you how many valid unicast frames have been received
from the local LAN but filtered out since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.9.4 |
rLocLANFilterInMCastsTells you how many valid multicast frames (filtered
frames and forwarded frames) have been received
from the local LAN since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.5 |
rLocLANFilterInMCastFwdsTells you how many valid multicast frames have been received
from the local LAN and forwarded to the remote LAN
since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.6 |
rLocLANFilterInMCastFiltsTells you how many valid multicast frames have been received
from the local LAN but filtered out since the last
system reset.ro Counter .1.3.6.1.4.1.64.9.9.7 |
rLocLANFilterInBCastsTells you how many valid broadcast frames (filtered
frames and forwarded frames) have been received
from the local LAN since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.8 |
rLocLANFilterInBCastFwdsTells you how many valid broadcast frames have been received
from the local LAN and forwarded to the remote LAN
since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.9 |
rLocLANFilterInBCastFiltsTells you how many valid broadcast frames have been received
from the local LAN and filtered out since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.10 |
rLocLANFilterDiscTransTells you how many frames have been queued to be
transmitted but discarded because their transit delay
exceeded the maximum since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.11 |
rLocLANFilterResShortsTells you how many frames have been queued to be
transmitted but discarded due to a shortage of
internal resource(s) since the last system reset.ro Counter .1.3.6.1.4.1.64.9.9.12 |
rlanFilterCfgGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.10 |
rFilterCfgLocAgingTimeEnter the length of time (in seconds) a station entry for a
local LAN that has become inactive should remain in
the filter table.rw INTEGER .1.3.6.1.4.1.64.9.10.1 |
rFilterCfgRemAgingTimeEnter the length of time (in seconds) a station entry for a
remote LAN that has become inactive should remain in
the filter table.rw INTEGER .1.3.6.1.4.1.64.9.10.2 |
rFilterCfgAgingStateChoose to disable or enable dynamic aging of station entries
from the filter table.rw Enumeration .1.3.6.1.4.1.64.9.10.3 |
rFilterCfgBlockRoamChoose to disable or enable block roaming.rw Enumeration .1.3.6.1.4.1.64.9.10.4 |
rlanMACFilterGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.11 |
rlanMACFilterTableThis table provides a management view of the
system configuration specific to individual MAC
addresses. The table is indexed using the physical
address (MAC address). SEQUENCE OF RlanMACFilterEntry .1.3.6.1.4.1.64.9.11.1 |
rlanMACFilterEntry RlanMACFilterEntry .1.3.6.1.4.1.64.9.11.1.1 |
rMACIDTells you the MAC address of one entry in the filter table.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.64.9.11.1.1.1 |
rMACTypeEnter the MAC address type, which can be one of the following:
1- dynamic - the MAC address was learned and is subject to
age out if aging is enabled.
2- static - the MAC address was manually entered in the
system through the console or SNMP
3- blocked - the system will filter this MAC address.
4- invalid - used to delete MAC filter entries.
NOTE: You can create or set a MAC address with a dynamic type.
That MAC address will simply be subject to aging as soon as it's
created or modified.rw Enumeration .1.3.6.1.4.1.64.9.11.1.1.2 |
rMACHomePortEnter the id for the remote LAN associated with this MAC address.
1) A rMACHomePort with a value of 0 means that the MAC
address resides on the local LAN.
2) A rMACHomePort with a value from 1 to 1000 will map to
the rRemLANID attribute of 1 to 1000.
This attribute cannot be SET alone. A GEN_ERROR will be
returned. If you want to change the home port on which the
MAC resides, you have to delete by setting rMACType to
INVALID and then recreate the entry by having all the attributes
in the same SET-REQUEST packet with valid values.
NOTE: If you want to create a new MAC
entry, you have to make sure that the rMACHomePort
attribute that you use has already been created and is, therefore,
known by the system.rw INTEGER .1.3.6.1.4.1.64.9.11.1.1.3 |
rlanTCPIPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.12 |
rTCPIPAddressEnter the IP address of your system.rw IpAddress .1.3.6.1.4.1.64.9.12.2 |
rTCPIPSubMaskEnter the subnet mask.rw IpAddress .1.3.6.1.4.1.64.9.12.3 |
rTCPIPDefGwEnter the IP address of the default gateway.rw IpAddress .1.3.6.1.4.1.64.9.12.4 |
rlanTelnetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.12.5 |
rTelnetAccessChoose to disable or enable the acceptance of an incoming TELNET
connection.rw Enumeration .1.3.6.1.4.1.64.9.12.5.1 |
rTelnetIpAddrEnter the IP address of an acceptable host for a TELNET connection.rw IpAddress .1.3.6.1.4.1.64.9.12.5.2 |
rTelnetIpSubMaskEnter the mask to be used when an incoming Telnet request
is being processed. The source IP address is masked
with this attribute and compared to the rTelnetIpAddr attribute
for access privileges.rw IpAddress .1.3.6.1.4.1.64.9.12.5.3 |
rFtpByteCountTells you how many bytes have been transferred
during a file transfer that is in process. If no file
transfer is in process, the field will display a value
zero (0).ro Gauge .1.3.6.1.4.1.64.9.12.6 |
rFtpInProgressTells you if a file transfer is progress.ro Enumeration .1.3.6.1.4.1.64.9.12.7 |
rFtpLastResultCodeTells you the Last Result Code for the last file transfer that took place.ro Enumeration .1.3.6.1.4.1.64.9.12.8 |
rFtpConfigTableThese objects manage the system's embedded ftp client and can
be used to initiate file transfers to or from a specified ftp
server. SEQUENCE OF RFtpConfigEntry .1.3.6.1.4.1.64.9.12.9 |
rFtpConfigEntry RFtpConfigEntry .1.3.6.1.4.1.64.9.12.9.1 |
rFtpFileIdTells you the file ID for this entry, which can be
code, database or auditRecords.ro Enumeration .1.3.6.1.4.1.64.9.12.9.1.1 |
rFtpServerIpAddrEnter the IP address of the FTP server.rw IpAddress .1.3.6.1.4.1.64.9.12.9.1.2 |
rFtpClientIdEnter the user ID to be used when the system identifies its embedded
FTP client to the FTP server. You must enter this information when
you issue a set for code(1) or database(2) file transfers.rw DisplayString .1.3.6.1.4.1.64.9.12.9.1.3 |
rFtpClientPasswdEnter the user password to be used when the sytem identifies its
embedded FTP client to the FTP server. You must enter this information when
you issue a set for code(1) or database(2) file transfers.rw DisplayString .1.3.6.1.4.1.64.9.12.9.1.4 |
rFtpFilePathEnter the directory path on the FTP server that the file is to be
copied to/from.rw DisplayString .1.3.6.1.4.1.64.9.12.9.1.5 |
rFtpFileNameEnter the filename to be used when the file is
saved on the FTP server.rw DisplayString .1.3.6.1.4.1.64.9.12.9.1.6 |
rFtpOperationSelect the operation the RSC should perform: get, put, or setup. The
get(1) operation is allowed on code and database records. The
put(2) operation is allowed on database files and audit records.
The setup(3) operation is allowed on all records, which commits
the parameters to non-volatile storage. Setting this object
to either get(1) or put(2) initiates a file transfer that
will be trapped on completion. The get and put operations also
perform an implied commit to non-volatile storage.
DEFAULT = setuprw Enumeration .1.3.6.1.4.1.64.9.12.9.1.7 |
rTCPIPDynamicIPEnter the start IP address of the dynamic IP pool.rwobsolete IpAddress .1.3.6.1.4.1.64.9.12.10 |
rTCPIPNumDynIpEnter the number of dynamic IPs in the pool.rwobsolete INTEGER .1.3.6.1.4.1.64.9.12.11 |
rlanBlacklistGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.13 |
rlanBlacklistTableThis table provides a management view of the
system configuration specific to individual
blacklisted phone numbers. SEQUENCE OF RlanBlacklistEntry .1.3.6.1.4.1.64.9.13.1 |
rlanBlacklistEntry RlanBlacklistEntry .1.3.6.1.4.1.64.9.13.1.1 |
rBlacklistIDTells you the ID of any of the possible 64
blacklisted entries.ro INTEGER .1.3.6.1.4.1.64.9.13.1.1.1 |
rBlacklistCLIDTells you the blacklisted phone number.rw DisplayString .1.3.6.1.4.1.64.9.13.1.1.2 |
rBlacklistStatusTells you the current status of this blacklisted entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.13.1.1.3 |
rBlacklistIDUnusedIdentifies a potentially unused index
that can be used as the rBlacklistID instance when you're creating
new entries in the rlanBlacklistTable. A returned value of
zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.13.2 |
rlanProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.14 |
rlanProtocolTableThis table provides a management view of the
system configuration specific to network addresses.
The table is indexed using the network IP address. SEQUENCE OF RlanProtocolEntry .1.3.6.1.4.1.64.9.14.1 |
rlanProtocolEntryOnce an entry has been created it cannot be modified.
It must be deleted first. RlanProtocolEntry .1.3.6.1.4.1.64.9.14.1.1 |
rProtocolIDTells you the network address of one entry in the protocol
table. It represents a unique device attached to
the associated home port.ro NetworkAddress .1.3.6.1.4.1.64.9.14.1.1.1 |
rProtocolMaskTells you the network mask associated with this unique
entry.rw NetworkAddress .1.3.6.1.4.1.64.9.14.1.1.2 |
rProtocolRemLANIDTells you the ID of the remote LAN associated with this
network address. The value maps one- to-one to the value
for the attribute rRemLANID.rw INTEGER .1.3.6.1.4.1.64.9.14.1.1.3 |
rProtocolTypeEnter the network-address type associated with this
unique entry.
DEFAULT = iprw Enumeration .1.3.6.1.4.1.64.9.14.1.1.4 |
rProtocolStatusTells you the current status of this protocol entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.14.1.1.5 |
rlanPriPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.15 |
rlanPriPortTableThis table provides a management view of the
system configuration specific to individual PRI
Ports. SEQUENCE OF RlanPriPortEntry .1.3.6.1.4.1.64.9.15.1 |
rlanPriPortEntry RlanPriPortEntry .1.3.6.1.4.1.64.9.15.1.1 |
rPortCardIDTells you the position of this card within the hub with respect to
the P2 backplane. Each PRI card can take slot position 1 to 10.ro INTEGER .1.3.6.1.4.1.64.9.15.1.1.1 |
rPortPortIDTells you the port ID for a specific interface.ro INTEGER .1.3.6.1.4.1.64.9.15.1.1.2 |
rPortCardTypeTells you the card type to which this port belongs,
which can be one of pri9360DB15, pri9346DB15, pri9330BNC,
pri9330DB15, pri9323DB15.ro Enumeration .1.3.6.1.4.1.64.9.15.1.1.3 |
rPortLineFormatSelect the line format to be used by a PRI port,
which can be one of naDS1ESF, naDS1D4, naDS1D4B8ZS, euroCEPT,
euroCEPTCRC4.
The first three are North American; the last two are European.rw Enumeration .1.3.6.1.4.1.64.9.15.1.1.4 |
rPortPRISwitchSelect the switch type to
which this PRI port connects, which can be one of att4ESS,
att5ESS, ntDMS100, ntDMS250, leased, dass2, dass15, euroisdn,
kdd. NOTE: The dass15 switch type is valid only if the timeslot
is less than 16; any B channels above timeslot 16 will be invalid.rw Enumeration .1.3.6.1.4.1.64.9.15.1.1.5 |
rPortDChanFormatSelect the format of the D Channel
to be used by this port, which can be one of 64 Kbps, 64 Kbps
inverted or 56 Kbps. European standards allow only 64kbps inverted.
NOTE: This attribute is applicable only if the port is not leased.
If the port is leased, a get or set will generate
a noSuchName error. The system will skip this port
if the previous attribute has initiated a get-next.rw Enumeration .1.3.6.1.4.1.64.9.15.1.1.6 |
rPortDChanTimeslotEnter the timeslot to be used by the D channel.
Valid timeslots for the various switch types are:
North American: 1..24
European: 1..31
DASS2-15: 1..16
NOTE: This attribute is applicable only if the port is not leased.
If the port is leased, a get or set will generate
a noSuchName error. The system will skip this port
if the previous attribute has initiated a get-next.rw INTEGER .1.3.6.1.4.1.64.9.15.1.1.7 |
rPortYellowAlarmTells you if the YELLOW alarm is off
or on. If it's on, the network
cannot synchronize itself with the data transmitted
by the PRI port.ro Enumeration .1.3.6.1.4.1.64.9.15.1.1.8 |
rPortAISAlarmTells you if the AIS alarm is off or on.
If it's on, the network cannot accept calls.ro Enumeration .1.3.6.1.4.1.64.9.15.1.1.9 |
rPortRedAlarmTells you if the RED alarm is off or on. If it's on,
the PRI port has failed to synchronize with the received data.ro Enumeration .1.3.6.1.4.1.64.9.15.1.1.10 |
rPortPhoneNumberTells you the phone number that this port answers for.
NOTE: This attribute is applicable only if the port is not leased.
If the port is leased, a get or set will generate
a noSuchName error. The system will skip this port
if the previous attribute has initiated a get-next.rw DisplayString .1.3.6.1.4.1.64.9.15.1.1.11 |
rPortAdmstSelect this option to enable a port.
If a port is disabled, current calls won't be torn down,
but the port will not accept or originate
subsequent calls. If the port is enabled, it will both
accept and originate calls.
DEFAULT = enabledrw Enumeration .1.3.6.1.4.1.64.9.15.1.1.12 |
rPortDLinkNumIndicates which port this D channel resides on.rw INTEGER .1.3.6.1.4.1.64.9.15.1.1.13 |
rPortIfIdThe identifier of the interface of interest.rw INTEGER .1.3.6.1.4.1.64.9.15.1.1.14 |
rPortDOSBSSelect this option to enable digital over speech bearer.rw Enumeration .1.3.6.1.4.1.64.9.15.1.1.15 |
rPortHuntGroupIndicates the huntgroup used by this remote LAN.
1 indicates that no Hunt group is defined for this
port.rw INTEGER ( 1..16 ) .1.3.6.1.4.1.64.9.15.1.1.16 |
rPortHoldOffEnter the time (in seconds) between a leased line failure
and the time before a reconnection is tried.
DEFAULT = 10rw INTEGER .1.3.6.1.4.1.64.9.15.1.1.17 |
rPortNetsyncSelect whether to source the system clock from this network
connection.rw Enumeration .1.3.6.1.4.1.64.9.15.1.1.18 |
rPortPBXTypeSelect the type of PBX attached to the port.rw Enumeration .1.3.6.1.4.1.64.9.15.1.1.19 |
rPortIsdnRoutingTableThis table provides a management view of the
call routing table specific to a PRI port connected to
an ISDN network. SEQUENCE OF RlanPortIsdnRoutingEntry .1.3.6.1.4.1.64.9.15.2 |
rPortIsdnRoutingEntry RlanPortIsdnRoutingEntry .1.3.6.1.4.1.64.9.15.2.1 |
rPortIsdnRoutingEnter the index number of the rIsdnDDIRoutingTable associated
with this port. Selecting none (0) forces the call type to be
determined in-band.
DEFAULT = 0rw INTEGER .1.3.6.1.4.1.64.9.15.2.1.1 |
rPortPBXRoutingTableThis table provides a management view of the
call routing table specific to a PRI port connected to
a PBX. SEQUENCE OF RlanPortPBXRoutingEntry .1.3.6.1.4.1.64.9.15.3 |
rPortPBXRoutingEntry RlanPortPBXRoutingEntry .1.3.6.1.4.1.64.9.15.3.1 |
rPortPBXRoutingEnter the index number of the rPbxCallRoutingTable associated
with this port. Selecting none (0) forces the call type to be
determined in-band.
DEFAULT = 0rw INTEGER .1.3.6.1.4.1.64.9.15.3.1.1 |
rlanIPXGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.16 |
rIPXWatchdogSpoofingSelect this option to enable watchdog spoofing from the
local LAN.rw Enumeration .1.3.6.1.4.1.64.9.16.1 |
rIPXWatchdogSpoofingTimerEnter the length of time ( in seconds) that spoofing should continue.rw INTEGER .1.3.6.1.4.1.64.9.16.2 |
rIPXSAPLearningTell the system whether it should learn
SAPs. When you want the system to learn SAPs, select one of:
start-keep-static - Static entries are saved
start-drop-static - Static entries are deleted
NOTE: You can enable learning only when bridging is disabled and no calls
are active.rw Enumeration .1.3.6.1.4.1.64.9.16.3 |
rIPXSAPLearningOPStateTells you whether or not the system is in SAP learning mode.ro Enumeration .1.3.6.1.4.1.64.9.16.4 |
rIPXLearntSAPsTells you how many SAP the system has learned
since the last learned mode was enabled.ro Counter .1.3.6.1.4.1.64.9.16.5 |
rlanSAPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.17 |
rlanSAPTableThe IPX Service Advertisement Protocol table. SEQUENCE OF RlanSAPEntry .1.3.6.1.4.1.64.9.17.1 |
rlanSAPEntry RlanSAPEntry .1.3.6.1.4.1.64.9.17.1.1 |
rSAPServiceTypeTells you the type of service that this server provides at this socket.
For example:
01h = user
04h = file server
07h = printer server
27h = TCP/IP gatewayro INTEGER .1.3.6.1.4.1.64.9.17.1.1.1 |
rSAPServerNameTells you the name of the server.ro OCTET STRING .1.3.6.1.4.1.64.9.17.1.1.2 |
rSAPTypeSelect the option that indicates how this entry was learned
(dynamic or static).
DEFAULT = staticrw Enumeration .1.3.6.1.4.1.64.9.17.1.1.3 |
rSAPNetworkAddressEnter the network address of the server.rw OCTET STRING .1.3.6.1.4.1.64.9.17.1.1.4 |
rSAPNodeAddressEnter the 48-bit node address of the server.rw OCTET STRING .1.3.6.1.4.1.64.9.17.1.1.5 |
rSAPSocketAddressEnter the socket address of the server.
For example, 04 53 = Routing Info Protocol.rw INTEGER .1.3.6.1.4.1.64.9.17.1.1.6 |
rSAPHopsEnter the number of routers to go through to reach the specified
server.rw INTEGER .1.3.6.1.4.1.64.9.17.1.1.7 |
rSAPGroupEnter the SAP group that this entry belongs to.rw INTEGER .1.3.6.1.4.1.64.9.17.1.1.8 |
rSAPStatusThe current status of this SAP entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.17.1.1.9 |
rSAPGroupIdUnusedThis object is used to identify a potentially unused index
that can be used as the rSAPGroupId instance when creating
new entries in the rlanSAPGroupTable. A returned value of
zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.17.2 |
rlanSAPGroupTableThis table provides an administrative view of the
SAP group table. SEQUENCE OF RlanSAPGroupEntry .1.3.6.1.4.1.64.9.17.3 |
rlanSAPGroupEntryEach entry in this table is a SAP group
name. Each name is used to group learned (and static)
IPX services together to form a SAP group. This group
can then be assigned to a remote LAN that is interested
in this grouping of IPX services.
Two default entries exist in this table which cannot be
modified or deleted. A rSAPGroupId value of 1 corresponds
to the 'All' SAP group, a rSAPGroupId value of 2 corresponds
to the 'Default' SAP group. All learned IPX services in the
SAP table default to the 'Default' group and all IPX services
logically belong to the 'All' group. RlanSAPGroupEntry .1.3.6.1.4.1.64.9.17.3.1 |
rSAPGroupIdTells you the index of the entry.ro INTEGER .1.3.6.1.4.1.64.9.17.3.1.1 |
rSAPGroupNameEnter the identifier for this SAP group.
NOTE: SAP group names must be unique,
but they're not case sensitive. You cannot modify
the two default entries (All and Default).rw DisplayString .1.3.6.1.4.1.64.9.17.3.1.2 |
rSAPGroupStatusEnter the current status of this entry.
NOTE: Entries that are currently
in use (e.g., either referenced by a remote LAN or in the
rlanSAPTable) cannot be destroyed. The default entries 'All'
and 'Default' cannot be destroyed.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.17.3.1.3 |
rlanRIPGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.18 |
rlanRIPTableThe IPX Routing Information Protocol table. SEQUENCE OF RlanRIPEntry .1.3.6.1.4.1.64.9.18.1 |
rlanRIPEntry RlanRIPEntry .1.3.6.1.4.1.64.9.18.1.1 |
rRIPNetworkAddressTells you the network address of this route.ro OCTET STRING .1.3.6.1.4.1.64.9.18.1.1.1 |
rRIPHopsTells you the number of routers to go through before reaching
this network.ro INTEGER .1.3.6.1.4.1.64.9.18.1.1.2 |
rRIPTicksTells you how long (in time-ticks) it takes to reach this network.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.18.1.1.3 |
rRIPMACAddressTells you the physical (MAC) address of the remote LAN.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.64.9.18.1.1.4 |
rlanSnmpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.19 |
rlanSnmpSetStatusThis object records the result code of the last SNMP set
operation. On a set that fails this object can be retrieved
to enhance the error codes provided by the SNMP protocol.
If the set response contains a non zero error index then
this object relates to the object in the set request as
indicated by the error index (as per normal PDU error
parsing). If the set response message indicates an error but
the error index is zero then this object pertains to the
semantics of the attempted set operation on the system as
as whole (e.g. table full).ro Enumeration .1.3.6.1.4.1.64.9.19.1 |
rSnmpCommunityIndexUnusedThis object is used to identify a potentially unused index
that can be used as the rSnmpCommunityIndex instance when
creating new entries in the rlanSnmpCommunityTable. A
returned value of zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.19.2 |
rlanSnmpCommunityTableThis table provides a management view of which device can
poll this resource via SNMP based on the Community Name,
IP address, Privilege and MIB view. SEQUENCE OF RlanSnmpCommunityEntry .1.3.6.1.4.1.64.9.19.3 |
rlanSnmpCommunityEntryThis is a list of attributes that make the Community
Table. RlanSnmpCommunityEntry .1.3.6.1.4.1.64.9.19.3.1 |
rSnmpCommunityIndexTells you the index entry of this community.ro INTEGER .1.3.6.1.4.1.64.9.19.3.1.1 |
rSnmpCommunityNameTells you the name of a community supported by this SNMP agent.rw DisplayString .1.3.6.1.4.1.64.9.19.3.1.2 |
rSnmpCommunityIpAddrEnter the IP address of a manager associated with a community
that will be supported by the SNMP agent. NOTE: A value of
zero means that all managers from that community will be
supported.rw IpAddress .1.3.6.1.4.1.64.9.19.3.1.3 |
rSnmpCommunityPrivEnter the access privilege associated with this community,
which can be one of none, readOnly, or readWrite.
DEFAULT = readOnlyrw Enumeration .1.3.6.1.4.1.64.9.19.3.1.4 |
rSnmpCommunityViewIndexEnter the identifier for the MIB view that is visible to this
community.
DEFAULT = 2rw INTEGER .1.3.6.1.4.1.64.9.19.3.1.5 |
rSnmpCommunityRowStatusEnter the current status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.19.3.1.6 |
rSnmpTrapCommunityIndexUnusedThis object is used to identify a potentially unused index
that can be used as the rSnmpTrapCommunityIndex instance when
creating new entries in the rlanSnmpTrapCommunityTable. A
returned value of zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.19.4 |
rlanSnmpTrapCommunityTableThis table provide a management view of which device(s)
(i.e., LAN Managers) this resource will send traps to. SEQUENCE OF RlanSnmpTrapCommunityEntry .1.3.6.1.4.1.64.9.19.5 |
rlanSnmpTrapCommunityEntryThis is a list of attributes that make the trap
community table. RlanSnmpTrapCommunityEntry .1.3.6.1.4.1.64.9.19.5.1 |
rSnmpTrapCommunityIndexTells you the index of this community entry.ro INTEGER .1.3.6.1.4.1.64.9.19.5.1.1 |
rSnmpTrapCommunityNameEnter the name of a trap community associated with a LAN
manager.rw DisplayString .1.3.6.1.4.1.64.9.19.5.1.2 |
rSnmpTrapIpAddrEnter the IP address of a manager that will receive traps
generated by this SNMP agent.rw IpAddress .1.3.6.1.4.1.64.9.19.5.1.3 |
rSnmpTrapRemotePortEnter the remote UDP port number used by an agent to receive traps.
DEFAULT = 162rw INTEGER .1.3.6.1.4.1.64.9.19.5.1.4 |
rSnmpTrapStatusEnter the current status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.19.5.1.5 |
rSnmpViewNameIndexUnusedThis object is used to identify a potentially unused index
that can be used as the rSnmpViewNameIndex instance when
creating new entries in the rlanSnmpViewNameTable. A
returned value of zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.19.6 |
rlanSnmpViewNameTableThe table is contained in the local database which defines local
MIB views. Reference RFC 1647 for details on MIB views. This
table has been adopted from RFC 1647 to an SNMPv1 environment
however the logic is the same. SEQUENCE OF RlanSnmpViewNameEntry .1.3.6.1.4.1.64.9.19.7 |
rlanSnmpViewNameEntry RlanSnmpViewNameEntry .1.3.6.1.4.1.64.9.19.7.1 |
rSnmpViewNameIndexTells you the index identifier of the name entry for this MIB view.
NOTE: MIB view indexes one(1) and two(2) are statistically configured
and cannot be modified.ro INTEGER .1.3.6.1.4.1.64.9.19.7.1.1 |
rSnmpViewNameEnter the ASCII name assigned to this MIB view.rw DisplayString .1.3.6.1.4.1.64.9.19.7.1.2 |
rSnmpViewNameStatusEnter the current status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.19.7.1.3 |
rlanSnmpViewTableThe table is contained in the local database which defines local
MIB views. Reference RFC 1647 for details on MIB views. This
table has been adopted from RFC 1647 to a SNMPv1 enironment
however the logic is the same. SEQUENCE OF RlanSnmpViewEntry .1.3.6.1.4.1.64.9.19.8 |
rlanSnmpViewEntry RlanSnmpViewEntry .1.3.6.1.4.1.64.9.19.8.1 |
rSnmpViewSubtreeIdentifies a MIB subtree.ro OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.19.8.1.1 |
rSnmpViewMaskThe bit mask which, in combination with the
corresponding instance of viewSubtree, defines a
family of view subtrees.
Each bit of this bit mask corresponds to a sub-
identifier of viewSubtree, with the most
significant bit of the i-th octet of this octet
string value (extended if necessary, see below)
corresponding to the (8*i - 7)-the sub-identifier,
and the least significant bit of the i-th octet of
this octet string corresponding to the (8*i)-th
sub-identifier, where i is in the range 1 through
16.
Each bit of this bit mask specifies whether or not
the corresponding sub-identifiers must match when
determining if an OBJECT IDENTIFIER is in this
family of view subtrees; a '1' indicates that an
exact match must occur; a '0' indicates 'wild
card', i.e., any sub-identifier value matches.
Thus, the OBJECT IDENTIFIER X of an object
instance is contained in a family of view subtrees
if the following criteria are met:
for each sub-identifier of the value of
viewSubtree, either:
the i-th bit of viewMask is 0, or
the i-th sub-identifier of X is equal to
the i-th sub-identifier of the value of
viewSubtree.
If the value of this bit mask is M bits long and
there are more than M sub-identifiers in the
corresponding instance of viewSubtree, then the
bit mask is extended with 1's to be the required
length.
Note that when the value of this object is the
zero-length string, this extension rule results in
a mask of all-1's being used (i.e., no 'wild
card'), and the family of view subtrees is the one
view subtree uniquely identified by the
corresponding instance of viewSubtree.rw OCTET STRING .1.3.6.1.4.1.64.9.19.8.1.2 |
rSnmpViewTypeThe status of a particular family of view
subtrees within the particular SNMPv2 context's
MIB view. The value, included(1), indicates that
the corresponding instances of viewSubtree and
viewMask define a family of view subtrees included
in the MIB view. The value, excluded(2),
indicates that the corresponding instances of
viewSubtree and viewMask define a family of view
subtrees excluded from the MIB view.rw Enumeration .1.3.6.1.4.1.64.9.19.8.1.3 |
rSnmpViewStatusEnter the status of this conceptual row in the viewTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.19.8.1.4 |
rlanSnmpTrapProfileTableThis table provides a management interface to the trap
profile table objects. SEQUENCE OF RlanSnmpTrapProfileEntry .1.3.6.1.4.1.64.9.19.9 |
rlanSnmpTrapProfileEntry RlanSnmpTrapProfileEntry .1.3.6.1.4.1.64.9.19.9.1 |
rSnmpTrapEnterpriseThe object identifier of the enterprise in which this trap
is defined. For example; to disable the gDChanUp trap defined
in this MIB this object would contain the object identifier
for gandalf (1.3.6.1.4.1.64).ro OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.19.9.1.1 |
rSnmpTrapIdThe unique trap id that the associated enterprise has assigned
this trap. For example; to disable the gDChanUp trap defined
in this MIB this object would contain the value 9024.ro INTEGER .1.3.6.1.4.1.64.9.19.9.1.2 |
rSnmpCommunitiesThe list of communities that are interested in this trap. Can
also be used to disable traps. Communities are represented as
a bit string where each bit in each octet represents a
community. The most significant bit of octet one represents
the community whose rSnmpTrapCommunityIndex value is one.rw OCTET STRING .1.3.6.1.4.1.64.9.19.9.1.3 |
rlanAuditGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.20 |
rAuditingEnabledSelect this option when you want to enable auditing. Can only be enabled
if a valid file transfer profile is set up for it.rw Enumeration .1.3.6.1.4.1.64.9.20.1 |
rAuditTimeOfDayTransferSelect this option when you want the system to transfer
audit records at a specified time of day
DEFAULT = disabledrw Enumeration .1.3.6.1.4.1.64.9.20.2 |
rAuditTimeOfDayEnter the time of day you want the system to initiate the file
transfer. NOTE: The times are entered as seconds but will only be accepted
on a 60 sec boundary. A value of zero indicates midnight, a value of 60
indicates 12:01, 43200 indicates 12am, 86340 indicates 23:59 and so on.
DEFAULT = 0rw INTEGER .1.3.6.1.4.1.64.9.20.3 |
rAuditRecordTermCharsSelect the way you want the system to
set up the termination records for individual audit records.
DEFAULT = crlfrw Enumeration .1.3.6.1.4.1.64.9.20.4 |
rAuditRecordsInFlashTells you how many audit records are
are currently in flash memory. NOTE: After a file transfer,
this field is reset to zero.ro Gauge .1.3.6.1.4.1.64.9.20.5 |
rlanFlashGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.21 |
rlanFlashDirectoryTableThis table provides a management interface to the flash
directory listings. SEQUENCE OF RlanFlashDirectoryEntry .1.3.6.1.4.1.64.9.21.1 |
rlanFlashDirectoryEntry RlanFlashDirectoryEntry .1.3.6.1.4.1.64.9.21.1.1 |
rFlashFileIndexTells you the directory index associated with this file in flash memory.ro INTEGER .1.3.6.1.4.1.64.9.21.1.1.1 |
rFlashFileTypeTells you the type of file (e.g., BRI
operating software) associated with this entry.rw DisplayString .1.3.6.1.4.1.64.9.21.1.1.2 |
rFlashFileIdTells you id of this file in flash memory .ro INTEGER .1.3.6.1.4.1.64.9.21.1.1.3 |
rFlashFileAddressTells you the address of this file in flash memory.ro OCTET STRING .1.3.6.1.4.1.64.9.21.1.1.4 |
rFlashFileSizeTells you (in bytes) the size of this file in flash memory.ro INTEGER .1.3.6.1.4.1.64.9.21.1.1.5 |
rFlashFileVersionTells you the software version of the file in flash memory.rw DisplayString .1.3.6.1.4.1.64.9.21.1.1.6 |
rFlashFileCrcTells you whether the checksum for the embedded file(s)
matches the checksum generated by the RSC.ro Enumeration .1.3.6.1.4.1.64.9.21.1.1.7 |
rlanLANProtocolIDGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.22 |
rLANProtocolIDIdUnusedThis object is used to identify a potentially unused index
that can be used as the rLANProtocolIDId instance when creating
new entries in the rlanLANProtocolIDTable. A returned value of
zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.22.1 |
rlanLANProtocolIDTableThis table provides an administrative view of the
LAN protocol ID table. SEQUENCE OF RlanLANProtocolIDEntry .1.3.6.1.4.1.64.9.22.2 |
rlanLANProtocolIDEntryEach entry in this table is a LAN protocol ID and
name. This entry can then be used in designing which
protocol that is to be filtered or forwarded.
Six default entries exist in this table which cannot be
modified or deleted. They are:
122 Novell IPX/SPX 8137
123 AppleTalk ARP 80F3
124 AppleTalk 809B
125 Reverse ARP 8035
126 ARP 0806
127 TCP/IP 0800 RlanLANProtocolIDEntry .1.3.6.1.4.1.64.9.22.2.1 |
rLANProtocolIDIdTells you the index of the entry.ro INTEGER .1.3.6.1.4.1.64.9.22.2.1.1 |
rLANProtocolID16 bit ID of the LAN protocol.
You cannot modify the predefined entries.rw INTEGER .1.3.6.1.4.1.64.9.22.2.1.2 |
rLANProtocolIDNameEnter the identifier for this LAN protocol ID.
You cannot modify the predefined entries.rw DisplayString .1.3.6.1.4.1.64.9.22.2.1.3 |
rLANProtocolIDStatusEnter the current status of this entry.
NOTE: Entries that are currently
in use (e.g., assigned to be filtered or forwarded)
cannot be destroyed. The predefined entries cannot be
destroyed.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.22.2.1.4 |
rlanModemGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.23 |
rlanMdmCountryThis attribute configures the system for a
specific country.
DEFAULT = United Statesrw Enumeration .1.3.6.1.4.1.64.9.23.1 |
rlanMdmModeDefines that modems are setup for either
originate or answer. When there is an
incomming call the setting in this object will
be the default for all the modems. On an outgoing
call the value of rRemLANMdmAnswer will control
the individual modem. DEFAULT = modemAnswerrw Enumeration .1.3.6.1.4.1.64.9.23.3 |
rlanMdmIDTableThe base table for the modems managed by this MIB. The
rlanMdmLineTable, rlanMdmDTEInterfaceTable,
rlanMdmCallControlTable, and rlanMdmStatsTable all augment
the rows defined in this table. SEQUENCE OF RlanMdmIDEntry .1.3.6.1.4.1.64.9.23.4 |
rlanMdmIDEntryEntries in this table are created only by the agent. One
entry exists for each modem managed by the agent. RlanMdmIDEntry .1.3.6.1.4.1.64.9.23.4.1 |
rMdmIDManufacturerOIDThis value is intended to identify the manufacturer, model,
and version of this modem. This may be used to identify the
existance of enterprise-specific functions and behaviours.ro OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.23.4.1.2 |
rlanMdmIDProductDetailsA textual description of this device, including the
manufacturer's name, modem model name, hardware revision,
firmware revision, and optionally, its serial number. The
exact format of this description is defined by the vendor.
This description may only contain characters from the NVT
ASCII character set.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.64.9.23.4.1.3 |
rlanMdmLineTableThe modem Line Table augments the modem ID table. SEQUENCE OF RlanMdmLineEntry .1.3.6.1.4.1.64.9.23.5 |
rlanMdmLineEntryEntries in this table are created only by the agent. One
entry exists for each modem managed by the agent. RlanMdmLineEntry .1.3.6.1.4.1.64.9.23.5.1 |
rMdmLineStateAllows the inspection of the state of the
modem.ro Enumeration .1.3.6.1.4.1.64.9.23.5.1.2 |
rlanMdmECTableThe modem error correcting table augments the modem ID
table. SEQUENCE OF RlanMdmECEntry .1.3.6.1.4.1.64.9.23.6 |
rlanMdmECEntryEntries in this table are created only by the agent. One
entry exists for each modem managed by the agent. RlanMdmECEntry .1.3.6.1.4.1.64.9.23.6.1 |
rMdmECErrorControlUsedIndicates the error control method used during the current
or previous call.ro Enumeration .1.3.6.1.4.1.64.9.23.6.1.1 |
rlanMdmDCTableThe modem data compression table augments the modem ID
table. SEQUENCE OF RlanMdmDCEntry .1.3.6.1.4.1.64.9.23.7 |
rlanMdmDCEntryEntries in this table are created only by the agent. One
entry exists for each modem managed by the agent. RlanMdmDCEntry .1.3.6.1.4.1.64.9.23.7.1 |
rMdmDCCompressionTypeUsedIndicates the data compression method used during the
current or previous call. If no compression protocol is in
use, this object shall have the value 1.ro Enumeration .1.3.6.1.4.1.64.9.23.7.1.1 |
rlanMdmSCTableThe modem signal convertor table augments the modem ID
table. SEQUENCE OF RlanMdmSCEntry .1.3.6.1.4.1.64.9.23.8 |
rlanMdmSCEntryEntries in this table are created only by the agent. One
entry exists for each modem managed by the agent. RlanMdmSCEntry .1.3.6.1.4.1.64.9.23.8.1 |
rMdmSCCurrentLineTransmitRateThe current link transmit rate of a connection, or the last
link transmit rate of the last connection in bits per
second.ro INTEGER .1.3.6.1.4.1.64.9.23.8.1.1 |
rMdmSCCurrentLineReceiveRateThe current link receive rate of a connection, or the last
link receive rate of the last connection in bits per
second.ro INTEGER .1.3.6.1.4.1.64.9.23.8.1.2 |
rMdmSCModulationSchemeUsedThe modulation scheme of the current or previous call.ro Enumeration .1.3.6.1.4.1.64.9.23.8.1.5 |
rlanMdmStatsTableThe modem statistics Table augments the modem ID table. SEQUENCE OF RlanMdmStatsEntry .1.3.6.1.4.1.64.9.23.9 |
rlanMdmStatsEntryEntries in this table are created only by the agent. One
entry exists for each modem managed by the agent. RlanMdmStatsEntry .1.3.6.1.4.1.64.9.23.9.1 |
rMdmStatsRetrainsThe number of retrains experienced on connections on this
line.ro Counter .1.3.6.1.4.1.64.9.23.9.1.1 |
rMdmStatsSentOctetsThe number of octets presented to the modem by the DTE.ro Counter .1.3.6.1.4.1.64.9.23.9.1.2 |
rMdmStatsReceivedOctetsThe number of octets presented to the DTE by the modem.ro Counter .1.3.6.1.4.1.64.9.23.9.1.3 |
rMdmStatsSentDataFramesThe number of data frames sent on the line interface. If
there is no frame-oriented protocol in use on the line
interface, this counter shall not increment.ro Counter .1.3.6.1.4.1.64.9.23.9.1.4 |
rMdmStatsReceivedDataFramesThe number of data frames received on the line interface.
If there is no frame-oriented protocol in use on the line
interface, this counter shall not increment.ro Counter .1.3.6.1.4.1.64.9.23.9.1.5 |
rMdmStatsResentFramesThe number of times this modem retransmits frames on the
line interface. If there is no frame-oriented protocol in
use on the line interface, this counter shall not
increment.ro Counter .1.3.6.1.4.1.64.9.23.9.1.6 |
rMdmStatsErrorFramesThe number of block errors received on the link. If there
is no frame-oriented protocol in use on the line interface,
this counter shall not increment.ro Counter .1.3.6.1.4.1.64.9.23.9.1.7 |
rMdmStatsDisconnectCauseThe disconnect reason of the last call.ro Enumeration .1.3.6.1.4.1.64.9.23.9.1.8 |
rMdmStatsControlListTells you the control signal state at the interface, which is bit-
mapped as follows:
Bit
0 RTS
1 DTR
2 CTS
3 DCD
4 DSR
5 TXDATA
6 RXDATA
7 OFFHOOK
8 SYNCINDICATION
9 MODEMRESET
10 RINGINDICATE
NOTE: Bit zero (0) is the least significant bit.ro INTEGER .1.3.6.1.4.1.64.9.23.9.1.9 |
rMdmStatsReceiveLevelReceived analog dBm level on the modem line.ro INTEGER .1.3.6.1.4.1.64.9.23.9.1.10 |
rMdmStatsTransmitLevelTransmitted analog dBm level on the modem line.ro INTEGER .1.3.6.1.4.1.64.9.23.9.1.11 |
rMdmStatsSignalToNoiseRatioThe signal to noise ration of the modem.ro INTEGER .1.3.6.1.4.1.64.9.23.9.1.12 |
rMdmStatsSpeedChangesThe number of speed changes.ro INTEGER .1.3.6.1.4.1.64.9.23.9.1.13 |
rlanMdmACCMTableThe ACC Mask table. SEQUENCE OF RlanMdmACCMEntry .1.3.6.1.4.1.64.9.23.10 |
rlanMdmACCMEntryEntries in this table are created only by the agent. One
entry exists for each modem managed by the agent. RlanMdmACCMEntry .1.3.6.1.4.1.64.9.23.10.1 |
rMdmACCMRxACCM Received.ro DisplayString .1.3.6.1.4.1.64.9.23.10.1.1 |
rMdmACCMTxACCM Transmitted.ro DisplayString .1.3.6.1.4.1.64.9.23.10.1.2 |
rlanPppGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.24 |
rPppNegotiateFirstThis attribute defines which PPP authentication protocol
is negotiated first on incoming call.
DEFAULT = chaprw Enumeration .1.3.6.1.4.1.64.9.24.1 |
rPppDynamicIPAddrThis attribute defines the start address
of the dynamic addres pool.rw IpAddress .1.3.6.1.4.1.64.9.24.2 |
rPppNumDynamicIPAddrThis attribute defines the number of
dynamic IP addresses in the pool.rw INTEGER .1.3.6.1.4.1.64.9.24.3 |
rPppDynamicIPAdrrHoldoffThis attribute defines the time in seconds befor
the same IP address can be reused after a call
has been disconnected.rw INTEGER .1.3.6.1.4.1.64.9.24.4 |
rPppDNSServerIPAddrThis attribute defines the DNS server IP address of
your Network.rw IpAddress .1.3.6.1.4.1.64.9.24.5 |
rPppRemDNSIPAddrHandlingThis attribute determines wether the system can accept
or override the DNS IP address submitted by
a remote system. DEFAULT = accept.
Override has been superceded by overridewith.rw Enumeration .1.3.6.1.4.1.64.9.24.6 |
rPppSecondaryDNSServerIPAddrThis attribute defines the Secondary DNS server IP address of
your Network.rw IpAddress .1.3.6.1.4.1.64.9.24.7 |
rPppPrimaryWINSServerIPAddrThis attribute defines the Primary WINS server IP address of
your Network.rw IpAddress .1.3.6.1.4.1.64.9.24.8 |
rPppSecondaryWINSServerIPAddrThis attribute defines the Secondary WINS server IP address of
your Network.rw IpAddress .1.3.6.1.4.1.64.9.24.9 |
rlanRemExtGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.25 |
rRemExtIDUnusedThis object is used to identify a potentially unused index
to be used as the rRemExtID when creating new entries in the
rlanRemExtConfigTable. A returned value of zero indicates that
the table is full.ro INTEGER .1.3.6.1.4.1.64.9.25.1 |
rlanRemExtConfigTableThis table provides a management view of the
system configuration specific to individual Remote
Extensions. SEQUENCE OF RlanRemExtConfigEntry .1.3.6.1.4.1.64.9.25.2 |
rlanRemExtConfigEntryThe conceptual row at instance zero is used by the
Xpressway/XpressStack as the default remote Extension
configuration. This entry is also used to change the defaults
chosen when manually configuring a new remote Extension
either through the embedded console or via SNMP. RlanRemExtConfigEntry .1.3.6.1.4.1.64.9.25.2.1 |
rRemExtIDTells you the index of this remote Extension. A value of
0 indicates the default remote-Extension configuration;
that is, this entry is used to determine the default
parameters for remote Extensionsro INTEGER .1.3.6.1.4.1.64.9.25.2.1.1 |
rRemExtNameEnter the name of the current remote Extension. The name
can use up to 16 characters but cannot contain spaces.
The combination of name and pbx extension number must
be unique. The default entry (instance zero) cannot be modified.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.2 |
rRemExtPbxExtensionThe numeric extension of this remote extension,
1 to 8 digits. Must be defined.
The combination of name and pbx extension number must
be unique. The default entry (instance zero) cannot be modified.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.3 |
rRemExtAdminStateThe current administrative state of the remote Extension.rw Enumeration .1.3.6.1.4.1.64.9.25.2.1.4 |
rRemExtPasswdAdminStateThe current Administrative state of the remote
Extension's password.rw Enumeration .1.3.6.1.4.1.64.9.25.2.1.5 |
rRemExtPasswdThe remote Extension password. Must be a numeric
string and must be defined if password admin state
is enabledrw DisplayString .1.3.6.1.4.1.64.9.25.2.1.6 |
rRemExtIdleDisconnectTimerThe time in seconds in which the call will
be disconnected when idle. Valid values are
5 to 300.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.7 |
rRemExtTimeOfDayProfileIdThe id of the remote extensions Time Of Day profilerw INTEGER .1.3.6.1.4.1.64.9.25.2.1.8 |
rRemExtConnectedToCardThe VIM card that this extension is connected to.
In the case of a 5232, use 1 for this field.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.9 |
rRemExtConnectedToModuleThe module that this extension is connected to.
In the case of a 5232, use 1 for this field.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.10 |
rRemExtConnectedToChannelThe channel of the module that this extension
is connected to.
In the case of a 5232, use 1 for this field.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.11 |
rRemExtPhoneEndPhNumberThe phone number at the phone end of this
PBX extender call.
The first character of this field can be
L(ocal), N(ational), or I(nternational).rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.12 |
rRemExtSwitchEndPhNumberThe phone number at the switch end of this
PBX extender call.
The first character of this field can be
L(ocal), N(ational), or I(nternational).rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.13 |
rRemExtDialPrefixThe index (1-33) of the dial prefix of this
remote extension. 1 means no dial prefix.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.14 |
rRemExtChannelGroupThe index (1-65) of the channel group of this
remote extension. 1 is the default group.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.15 |
rRemExtCLIDThe calling line ID of the remote unit. When
CLID security is enabled, the CLID must
match the number here for the call to be
accepted.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.16 |
rRemExtMakeSetBusyAdminStateThe administrative state of the MakeSetBusy
function.rw Enumeration .1.3.6.1.4.1.64.9.25.2.1.17 |
rRemExtMakeSetBusyKeyThe key value that activates the
MakeSetBusy functionrw DisplayString .1.3.6.1.4.1.64.9.25.2.1.18 |
rRemExtLogoutSequenceThe numeric logout sequence.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.19 |
rRemExtCallProcessingThe call processing type associated with
this remote extension.rw Enumeration .1.3.6.1.4.1.64.9.25.2.1.20 |
rRemExtStatusThe current status of this remote
extension entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.25.2.1.21 |
rRemExtCallForceTo tell the system to disconnect this remote Extension,
select disconnect from the list of available options.
When you select connect, the system will try to
connect to the remote Extension on an available channel
as specified in the rlanDestAddressConfigTable selection
parameters (i.e., channel group)
DEFAULT = statusQuo.rw Enumeration .1.3.6.1.4.1.64.9.25.2.1.22 |
rRemExtLineKeyThe mask representing the line keys to use.rw OCTET STRING .1.3.6.1.4.1.64.9.25.2.1.23 |
rRemExtRxGainThe attenuation or gain of the recieved
PBX signal. This value is stored in the
database as -7 to 9. It is represented
in this MIB as 1 to 17.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.24 |
rRemExtTxGainThe attenuation or gain of the transmitted
PBX signal. This value is stored in the
database as -9 to 7. It is represented
in this MIB as 1 to 17.rw INTEGER .1.3.6.1.4.1.64.9.25.2.1.25 |
rRemExtPbxInterfaceSelect the type of PBX connection used for this remote
extension
DEFAULT = vrm.rw Enumeration .1.3.6.1.4.1.64.9.25.2.1.26 |
rRemExtOutgoingBearerSelect the type of bearer to use for outgoing calls to this
remote extension.
DEFAULT = kbps64Unrestrict.rw Enumeration .1.3.6.1.4.1.64.9.25.2.1.27 |
rRemExtDivertImmediateThe phone number to divert all calls intended for this
extension to. For normal operation, leave this entry blank.
This entry can be modified from the remote extension using
a 'star' sequence.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.28 |
rRemExtDivertBusyThe phone number to divert all calls intended for this
extension to, whilst the extension is busy. Leave this
entry blank to disable this facility. This entry can be
modified from the remote extension using a 'star'
sequence.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.29 |
rRemExtDivertNoAnswerThe phone number to divert all calls intended for this
extension to, if there is no answer from this extension.
Leave this entry blank to disable this facility. This
entry can be modified from the remote extension using a
'star' sequence.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.30 |
rRemExtOfficeExtensionIf the home-worker also has an office extension number, it
should be entered here. Certain facilities are aonly available
to this extension for security purposes.rw DisplayString .1.3.6.1.4.1.64.9.25.2.1.31 |
rlanRemExtStatsTableThis table provides a management view of the
system configuration specific to individual Remote
Extensions. SEQUENCE OF RlanRemExtStatsEntry .1.3.6.1.4.1.64.9.25.3 |
rlanRemExtStatsEntry RlanRemExtStatsEntry .1.3.6.1.4.1.64.9.25.3.1 |
rRemExtVoiceModuleTells you the channel index of the Voice
module in use.ro INTEGER .1.3.6.1.4.1.64.9.25.3.1.1 |
rRemExtIsdnChanTells you the channel index of the ISDN
channel used.ro INTEGER .1.3.6.1.4.1.64.9.25.3.1.2 |
rRemExtTotalTimeTells you the total number of TimeTicks that have
elapsed while this remote extension has been connected.
This value resets when the RLAN resets. Returns a 0 if
a connection has yet to be made.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.25.3.1.3 |
rRemExtLastTimeTells you the time in TimeTicks of the last
connection to this remote extension. Returns
a 0 if a connection has yet to be made.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.25.3.1.4 |
rRemExtCallDurationTells you the number of TimeTicks that have
elapsed since this connection has been
established. This value resets every time the remote
extention reconnects. Returns a 0 if a connection
has yet to be made.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.9.25.3.1.5 |
rRemExtLastFailTells you the last calls failure code.ro INTEGER .1.3.6.1.4.1.64.9.25.3.1.6 |
rRemExtWANStatsIndexThis indicates active entry in the
rlanWANStatsTable entries. 0 indicates that
this remote LAN is currently not active (up).ro INTEGER .1.3.6.1.4.1.64.9.25.3.1.7 |
rlanTimeOfDayGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.26 |
rTimeOfDayIDUnusedThis object is used to identify a potentially
unused index to be used as the rRemTimeOfDayID
when creating new entries in the rlanRemTimeOfDayTable.
A returned value of zero indicates that the table is full.ro INTEGER .1.3.6.1.4.1.64.9.26.1 |
rlanTimeOfDayProfileTableThis table provides a management view of the
system configuration specific to individual Time Of
day entries. SEQUENCE OF RlanTimeOfDayEntry .1.3.6.1.4.1.64.9.26.2 |
rlanTimeOfDayProfileEntryPartial entry RlanTimeOfDayProfileEntry .1.3.6.1.4.1.64.9.26.2.1 |
rTimeOfDayProfileIDTells you the index of this Time Of Day entry.ro INTEGER .1.3.6.1.4.1.64.9.26.2.1.1 |
rTimeOfDayProfileNameTells you the name of this Time Of Day entry.
No whitespace and must be unique.
Must be defined.rw DisplayString .1.3.6.1.4.1.64.9.26.2.1.2 |
rTimeOfDayProfileStatusThe current status of this remote
extension entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.26.2.1.3 |
rlanTimeOfDayEntryTableThis table provides a management view of the
system configuration specific to individual Time Of
day profile entries. SEQUENCE OF RlanTimeOfDayEntry .1.3.6.1.4.1.64.9.26.3 |
rlanTimeOfDayEntryPartial entry RlanTimeOfDayEntry .1.3.6.1.4.1.64.9.26.3.1 |
rTimeOfDayEntryIDTells you the index of this Time Of Day profile entry.ro INTEGER .1.3.6.1.4.1.64.9.26.3.1.1 |
rTimeOfDayEntryStartThe start time of this TOD profile entry. The format
is an unsigned long taken from the number of minutes
from Sunday Midnight. For example, if the start time
is Monday at 06:00 this value would be 360. This
value must be less than rTimeOfDayProfileEnd and
larger than the end time of the previous entryrw INTEGER .1.3.6.1.4.1.64.9.26.3.1.2 |
rTimeOfDayEntryEndThe end time of this TOD profile entry. The format
is an unsigned long taken from the number of minutes
from Sunday Midnight. For example, if the start time
is Monday at 06:01 this value would be 361. This
value must be greater than rTimeOfDayProfileStart and
smaller than the start time of the next entry.rw INTEGER .1.3.6.1.4.1.64.9.26.3.1.3 |
rTimeOfDayEntryIdleDisconnectIs idle disconnect enabled or disabled during this
time span.rw Enumeration .1.3.6.1.4.1.64.9.26.3.1.4 |
rTimeOfDayEntryExclusiveIs exclusive enabled or disabled during this
time span. That is, are other phones allowed to
connect.rw Enumeration .1.3.6.1.4.1.64.9.26.3.1.5 |
rlanDpnssBchGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.27 |
rlanDpnssBchConfigTableThis table provides a management view of the
B-Channel configuration items specific to DPNSS links. SEQUENCE OF RlanDpnssBchConfigEntry .1.3.6.1.4.1.64.9.27.1 |
rlanDpnssBchConfigEntryEntry defining DPNSS specific B-channel attributes. RlanDpnssBchConfigEntry .1.3.6.1.4.1.64.9.27.1.1 |
rDpnssBchCardIDThe PRI card this entry is referring toro INTEGER .1.3.6.1.4.1.64.9.27.1.1.1 |
rDpnssBchPortIDThe PRI port this entry is referring toro INTEGER .1.3.6.1.4.1.64.9.27.1.1.2 |
rDpnssBchChanIDThe PRI B-channel this entry is referring toro INTEGER .1.3.6.1.4.1.64.9.27.1.1.3 |
rDpnssBchRealXySelect the collision handling of this B-channel. Each B-channel
should be set as X on one end of the link and Y on the other
end. If there is a call collision on this channel, the end
designated X will succeed, whilst the end designated Y will
drop back and retry on a different channel.
DEFAULT = x.rw Enumeration .1.3.6.1.4.1.64.9.27.1.1.4 |
rDpnssBchVirtualModeFor each B-channel on a DPNSS link there is a corresponding
virtual channel, which is used to signal call-independant
information through the network. Usually all of these channels
will be enabled, but a subset may be disabled.
DEFAULT = enabled.rw Enumeration .1.3.6.1.4.1.64.9.27.1.1.5 |
rDpnssBchVirtualXySelect the collision handling of this Virtual B-channel.
DEFAULT = x.rw Enumeration .1.3.6.1.4.1.64.9.27.1.1.6 |
rlanCallRoutingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.28 |
rlanIsdnDDIRoutingTableThis table provides a management view of the
ISDN Call Routing Table, used to provide incoming call
handling ability based on information in the ISDN Setup
message. SEQUENCE OF RlanIsdnDDIRoutingEntry .1.3.6.1.4.1.64.9.28.1 |
rlanIsdnDDIRoutingEntryEntry defining incoming call handling for ISDN initiated calls. RlanIsdnDDIRoutingEntry .1.3.6.1.4.1.64.9.28.1.1 |
rIsdnDDIRtgIndexUniquely identifies this entryro INTEGER .1.3.6.1.4.1.64.9.28.1.1.1 |
rIsdnDDIRtgNameTells you the name of this Routing Table entry.
No whitespace and must be unique.
Must be defined.rw DisplayString .1.3.6.1.4.1.64.9.28.1.1.2 |
rIsdnDDIRtgRacLoPhnumA range of phone numbers can be defined such that all
incoming calls with a dialled number in this range are
presented to the RAC as data calls. The default for
dialled numbers outside of this range is to route the
call to the PBX. This is the lower bound of the range.rw DisplayString .1.3.6.1.4.1.64.9.28.1.1.3 |
rIsdnDDIRtgRacHiPhnumA range of phone numbers can be defined such that all
incoming calls with a dialled number in this range are
presented to the RAC as data calls. The default for
dialled numbers outside of this range is to route the
call to the PBX. This is the higher bound of the range.rw DisplayString .1.3.6.1.4.1.64.9.28.1.1.4 |
rIsdnDDIRtgApexPhnumEnter the dialled number which is reserved for remote
analogue extensions to call.rw DisplayString .1.3.6.1.4.1.64.9.28.1.1.5 |
rIsdnDDIRtgAbsorbFor calls which are passed on to the PBX, a simple number
mapping algorithm can be performed on the dialled number to
accomodate the PBXs numbering plan. Enter the number of
digits to absorb from the front of the dialled number.rw INTEGER .1.3.6.1.4.1.64.9.28.1.1.6 |
rIsdnDDIRtgInsertFor calls which are passed on to the PBX, a simple number
mapping algorithm can be performed on the dialled number to
accomodate the PBXs numbering plan. Enter a digit string to
insert at the front of the dialled number.rw DisplayString .1.3.6.1.4.1.64.9.28.1.1.7 |
rIsdnDDIRtgRowStatusThe current status of this routing table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.28.1.1.8 |
rlanPbxCallRoutingTableThis table provides a management view of the
PBX Call Routing Table, used to provide incoming call
handling ability based on information Initial Service
Request Message (ISRM) from the PBX. SEQUENCE OF RlanPbxCallRoutingEntry .1.3.6.1.4.1.64.9.28.2 |
rlanPbxCallRoutingEntryEntry defining incoming call handling for PBX initiated calls. RlanPbxCallRoutingEntry .1.3.6.1.4.1.64.9.28.2.1 |
rPbxCallRtgIndexUniquely identifies this entryro INTEGER .1.3.6.1.4.1.64.9.28.2.1.1 |
rPbxCallRtgNameTells you the name of this Routing Table entry.
No whitespace and must be unique.
Must be defined.rw DisplayString .1.3.6.1.4.1.64.9.28.2.1.2 |
rPbxCallRtgGwayPhnumCalls from a PBX where the called number begins with this prefix
are routed directly into the ISDN, i.e. using the RLAN as an ISDN
gateway. Leave blank if calls from the PBX to the ISDN are not
required. An asterisk may be used to indicate
this is the default route.rw DisplayString .1.3.6.1.4.1.64.9.28.2.1.3 |
rPbxCallRtgGwayAbsorbWhen calls are routed through to the ISDN because they meet
the criteria above, this field indicates how many digits to
discard from the front of the called number. Generally the prefix
used for routing is absorbed.rw INTEGER .1.3.6.1.4.1.64.9.28.2.1.4 |
rPbxCallRtgRacExtLoWhen the RLAN has a PBX connection, a range of extension
numbers are allocated to the RLAN. Calls received by the
RLAN down the PBX trunk are treated as normal data calls.
This is the low-entry of the range.rw DisplayString .1.3.6.1.4.1.64.9.28.2.1.5 |
rPbxCallRtgRacExtHiWhen the RLAN has a PBX connection, a range of extension
numbers are allocated to the RLAN. Calls received by the
RLAN down the PBX trunk are treated as normal data calls.
This is the high-entry of the range.rw DisplayString .1.3.6.1.4.1.64.9.28.2.1.6 |
rPbxCallRtgApexExtLoWhen the RLAN has a PBX connection, a range of extension
numbers are allocated to Remote Extensions.
This is the low-entry of the range.rw DisplayString .1.3.6.1.4.1.64.9.28.2.1.7 |
rPbxCallRtgApexExtHiWhen the RLAN has a PBX connection, a range of extension
numbers are allocated to Remote Extensions.
This is the high-entry of the range.rw DisplayString .1.3.6.1.4.1.64.9.28.2.1.8 |
rPbxCallRtgRowStatusThe current status of this routing table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.64.9.28.2.1.9 |
rlanSecurityGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.29 |
rlanSecurityBannerConfigTableThis table provides a management view of the
login banner configuration parameters. SEQUENCE OF RlanSecurityBannerConfigEntry .1.3.6.1.4.1.64.9.29.1 |
rlanSecurityBannerConfigEntry RlanSecurityBannerConfigEntry .1.3.6.1.4.1.64.9.29.1.1 |
rSecBannerBannerThe authentication Banner String. This is the
banner that users see before they login. Printable
characters must be enclosed in quotation marks,
non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 512 bytes.rw DisplayString .1.3.6.1.4.1.64.9.29.1.1.1 |
rSecBannerLoginThe authentication Login prompt. Printable
characters must be enclosed in quotation marks,
non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 32 bytes.rw DisplayString .1.3.6.1.4.1.64.9.29.1.1.2 |
rSecBannerPasswordThe authentication Password prompt. Printable
characters must be enclosed in quotation marks,
non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 32 bytes.rw DisplayString .1.3.6.1.4.1.64.9.29.1.1.3 |
rSecBannerAcceptedThe authentication Accepted banner. This is the
banner the user sees when login is successful.
Printable characters must be enclosed in quotation
marks, non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 32 bytes.rw DisplayString .1.3.6.1.4.1.64.9.29.1.1.4 |
rSecBannerDeniedThe authentication Denied banner. This is the
banner the user sees when login is unsuccessful.
Printable characters must be enclosed in quotation
marks, non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 32 bytes.rw DisplayString .1.3.6.1.4.1.64.9.29.1.1.5 |
rSecBannerPart1The first part of the authentication Banner String.
This is the banner that users see before they login.
The banner is split into 3 parts to accomodate SNMP
implementations that cannot read strings larger than
256 characters.
Printable characters must be enclosed in quotation
marks, non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 512 bytes.ro DisplayString .1.3.6.1.4.1.64.9.29.1.1.6 |
rSecBannerPart2The second part of the authentication Banner String.
This is the banner that users see before they login.
The banner is split into 3 parts to accomodate SNMP
implementations that cannot read strings larger than
256 characters.
Printable characters must be enclosed in quotation
marks, non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 512 bytes.ro DisplayString .1.3.6.1.4.1.64.9.29.1.1.7 |
rSecBannerPart3The third part of the authentication Banner String.
This is the banner that users see before they login.
The banner is split into 3 parts to accomodate SNMP
implementations that cannot read strings larger than
256 characters.
Printable characters must be enclosed in quotation
marks, non printable characters entered in 3 digit
decimal numbers, separated by commas. Length
of banner to be sent must not exceed 512 bytes.ro DisplayString .1.3.6.1.4.1.64.9.29.1.1.8 |
rlanIpRoutingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.64.9.30 |
rlanIpRoutingConfigTableThis table provides a management view of the
login banner configuration parameters. SEQUENCE OF RlanIpRoutingConfigEntry .1.3.6.1.4.1.64.9.30.1 |
rlanIpRoutingConfigEntry RlanIpRoutingConfigEntry .1.3.6.1.4.1.64.9.30.1.1 |
rIpRoutingArpProxyEnables ARP Proxyrw Enumeration .1.3.6.1.4.1.64.9.30.1.1.1 |
rIpRoutingRipForwardingEnables RIP Forwardingrw Enumeration .1.3.6.1.4.1.64.9.30.1.1.2 |
rIpRoutingRipTypeThe type of RIP Forwardingrw Enumeration .1.3.6.1.4.1.64.9.30.1.1.3 |