GANDALF-ENTERPRISE-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for GANDALF-ENTERPRISE-MIB.
288
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
288 total| Object Name |
|---|
gandalf OBJECT IDENTIFIER .1.3.6.1.4.1.64 |
RFC1155-SMI Unknown .1.3.6.1.4.1.64 |
gCardInstalledThis trap indicates that a card was physically
installed in the hub. The trap description
identify the card slot number. TRAP-TYPE .1.3.6.1.4.1.64.0.100 |
gCardRemovedThis trap indicates that a card was physically
removed from the hub. The trap description
identify the card slot number. TRAP-TYPE .1.3.6.1.4.1.64.0.101 |
gCardMismatchThis trap indicates that a card was physically
installed in a slot configured with a different
card type. TRAP-TYPE .1.3.6.1.4.1.64.0.102 |
gCardMismatchClearedThis trap indicates that the slot causing a
Card Mismatch was reconfigured with the proper
card type. TRAP-TYPE .1.3.6.1.4.1.64.0.103 |
gPortThresholdExceededThis trap indicates a time based or frame
based threshold is exceeded on a given port.
The trap description will indicate the type of
threshold, as well as identifing the card
and port number. TRAP-TYPE .1.3.6.1.4.1.64.0.104 |
gNvramFaultThis trap indicates a critical hardware
failure: an NVRAM fault. TRAP-TYPE .1.3.6.1.4.1.64.0.105 |
gFiltDatabaseFullThis trap indicates that the number of entries
in the Filtering Database has reached the bridge's
storing capacity. TRAP-TYPE .1.3.6.1.4.1.64.0.106 |
gPowerSupplyFailedThis trap indicates that a fault was detected
on a power supply. The trap description will
indicate which of the two power supply is
faulty. TRAP-TYPE .1.3.6.1.4.1.64.0.107 |
gLogThresholdExceededThis trap indicates that the event log capacity
was exceeded. TRAP-TYPE .1.3.6.1.4.1.64.0.108 |
gLinkMismatchThis trap indicates that the configuration of a WAN
port is incompatible with the network topology. TRAP-TYPE .1.3.6.1.4.1.64.0.109 |
gLinkMismatchClearedThis trap indicates that the condition causing a
Link Mismatch was corrected. TRAP-TYPE .1.3.6.1.4.1.64.0.110 |
gNewRootThe newRoot trap indicates that the sending agent
has become the new root of the Spanning Tree; the
trap is sent by a bridge soon after its election
as the new root, e.g., upon expiration of the
Topology Change Timer immediately subsequent to
its election. TRAP-TYPE .1.3.6.1.4.1.64.0.111 |
gTopologyChangeA topologyChange trap is sent by a bridge when
any of its configured ports transitions from the
Learning state to the Forwarding state, or from
the Forwarding state to the Blocking state. The
trap is not sent if a newRoot trap is sent for the
same transition. TRAP-TYPE .1.3.6.1.4.1.64.0.112 |
gPortFailureA link to a port has failed. Possible reasons:
1. Master port idle receive timer has expired.
Port has been disabled and declared faulty.
Standby port will take over if ready.
2. Standby port idle receive timer has expired.
Port has been disabled and declared faulty. TRAP-TYPE .1.3.6.1.4.1.64.0.113 |
gandalf-hub OBJECT IDENTIFIER .1.3.6.1.4.1.64.1 |
hmBasicCapability OBJECT IDENTIFIER .1.3.6.1.4.1.64.1.1 |
hubBasicIDA 48-bit unique identifier, the hub ethernet address is used.ro OCTET STRING .1.3.6.1.4.1.64.1.1.1 |
hubCardCapacityThe number of groups (cards) that can be contained within the hub.ro INTEGER .1.3.6.1.4.1.64.1.1.2 |
hubCardMapA string of bits which reflects the current configuration of units
which are viewed by the Group managed objects. The length of the
bitstring is hubGroupCapacity bits. The LSBit relates to the unit
viewed by group 1. A '1' in the bitstring indicates presence of the
unit, '0' represent absence of the unit.ro OCTET STRING .1.3.6.1.4.1.64.1.1.3 |
hubNumOfRelaysShows the number of relays present without regard as to whether
or not each is enabled or disabled.ro INTEGER .1.3.6.1.4.1.64.1.1.4 |
hubRelayActiveAn integer that indicates which relay is active. Zero indicates
that no relays are active.ro INTEGER .1.3.6.1.4.1.64.1.1.5 |
hubResourceTypeAn integer value representing the IEEE802 Standard that applies
to this resource.ro INTEGER .1.3.6.1.4.1.64.1.1.6 |
hubStandardRevisionAn integer value representing the revision of the IEEE802 Standard
to which the station conforms with respect to that resource.ro INTEGER .1.3.6.1.4.1.64.1.1.7 |
hubIEEE8023LmeOptionsA set of option indicators, each of which, if present, indicates
that a particular option within NM_LME is supported. Its
interpretation is specified in the appropriate standard.ro OCTET STRING .1.3.6.1.4.1.64.1.1.8 |
hubManIDA 24 bit value that identifies the manufacturer.ro OCTET STRING .1.3.6.1.4.1.64.1.1.9 |
hubManProductIDA manufacturer-defined product identifier.ro OCTET STRING .1.3.6.1.4.1.64.1.1.10 |
hubManProductVersionA manufacturer-defined product revision designation.ro OCTET STRING .1.3.6.1.4.1.64.1.1.11 |
hubManTelephoneNumAn ascii representation of the manufacturer's telephone number.rw OCTET STRING .1.3.6.1.4.1.64.1.1.12 |
hubNameThis attribute is a text string up to 32 characters, of locally
determined significance.rw OCTET STRING .1.3.6.1.4.1.64.1.1.13 |
hubIPaddressThis attribute contains the IP address of the hub.ro NetworkAddress .1.3.6.1.4.1.64.1.1.14 |
hubEEpromRevThis attribute provides the eeprom revision number and
is read from the hardware.ro OCTET STRING .1.3.6.1.4.1.64.1.1.15 |
hubSecureModeAn integer value to set the hub in secure mode. In secure mode
all ports are disabled by default, otherwise ports are enabled
by default upon creation.rw Enumeration .1.3.6.1.4.1.64.1.1.16 |
hmBasicCardTableThis table provide a management view of the HUB
configuration specific to individual cards. SEQUENCE OF HmBasicCardEntry .1.3.6.1.4.1.64.1.1.17 |
hmBasicCardEntry HmBasicCardEntry .1.3.6.1.4.1.64.1.1.17.1 |
gCardIDAn 8 bit value unique within the hub.ro INTEGER .1.3.6.1.4.1.64.1.1.17.1.1 |
gCardNumberOfPortsThis attribute contains the number of ports in the card object
instance (MAC Entities).ro INTEGER .1.3.6.1.4.1.64.1.1.17.1.2 |
gCardNameThis attribute is a text string up to 32 characters, of locally
determined significance.rw OCTET STRING .1.3.6.1.4.1.64.1.1.17.1.3 |
gCardTypeThis attribute contains the type of card.ro OCTET STRING .1.3.6.1.4.1.64.1.1.17.1.4 |
gCardRingNumberAThis attribute contains the Ring number associated with a UTP2112
type of card, or with RI/RO set of ports 'A' for a STP4104 type of
card.rw Enumeration .1.3.6.1.4.1.64.1.1.17.1.5 |
gCardRingNumberBThis attribute contains the Ring number associated with RI/RO set
of ports 'B' for a STP4104 type of card.rw Enumeration .1.3.6.1.4.1.64.1.1.17.1.6 |
gCardIbmModeAThis attribute specifies wether RI/RO set of ports 'A' for a STP4104
type of card is in IBM mode or normal mode.rw Enumeration .1.3.6.1.4.1.64.1.1.17.1.7 |
gCardIbmModeBThis attribute specifies wether RI/RO set of ports 'B' for a STP4104
type of card is in IBM mode or normal mode.rw Enumeration .1.3.6.1.4.1.64.1.1.17.1.8 |
gCardRingSpeedAThis attribute specifies wether RI/RO set of ports 'A' for a STP4104
runs at 4 or 16 Mbps. It is also used to display the speed of a UTP2112
type of cards.rw Enumeration .1.3.6.1.4.1.64.1.1.17.1.9 |
gCardRingSpeedBThis attribute specifies wether RI/RO set of ports 'B' for a STP4104
runs at 4 or 16 Mbps.rw Enumeration .1.3.6.1.4.1.64.1.1.17.1.10 |
hmBasicPortTableThis table provide a management view of the HUB
configuration specific to individual ports. SEQUENCE OF HmBasicPortEntry .1.3.6.1.4.1.64.1.1.18 |
hmBasicPortEntry HmBasicPortEntry .1.3.6.1.4.1.64.1.1.18.1 |
gCardBasicIDAn 8 bit value unique within the hub.ro INTEGER .1.3.6.1.4.1.64.1.1.18.1.1 |
gPortIDAn 8 bit value unique in the group.ro INTEGER .1.3.6.1.4.1.64.1.1.18.1.2 |
gPortTypePort connector type.ro Enumeration .1.3.6.1.4.1.64.1.1.18.1.3 |
gPortAdminStateIndicates whether the port is enabled or disabled. A disabled port
neither transmit nor receives.rw Enumeration .1.3.6.1.4.1.64.1.1.18.1.4 |
gPortAutoPartitionStateIndicates whether the port is currently partitioned by the hub's
auto-partition protection.ro Enumeration .1.3.6.1.4.1.64.1.1.18.1.5 |
gPortNameThis attribute is a text string up to 32 characters, of locally
determined significance.rw OCTET STRING .1.3.6.1.4.1.64.1.1.18.1.6 |
gPortEffectiveStateIndicates redundant port's effective state.ro Enumeration .1.3.6.1.4.1.64.1.1.18.1.7 |
gPortConfigurationIndicates port's redundant configuration status.ro Enumeration .1.3.6.1.4.1.64.1.1.18.1.8 |
gPortRedundantPortIndicates redundant port's port number.rw INTEGER .1.3.6.1.4.1.64.1.1.18.1.9 |
gPortRedundantCardIndicates redundant port's card number.rw INTEGER .1.3.6.1.4.1.64.1.1.18.1.10 |
gPortLinkStatusIndicates port's link integrity status.ro Enumeration .1.3.6.1.4.1.64.1.1.18.1.11 |
hmSelfTestCapability OBJECT IDENTIFIER .1.3.6.1.4.1.64.1.2 |
hubSelfTestIDA 48-bit unique identifier, the hub ethernet address is used.ro OCTET STRING .1.3.6.1.4.1.64.1.2.1 |
hubTimeSinceResetThe time in tens of milliseconds since the last time that
the system was reset. This counter has a value of 0 when
initialized.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.1.2.2 |
hubResetTimeStampNot a counter, this attribute provides the value of hubTimeSinceReset
when the hub was last reset.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.1.2.3 |
hubHealthStateThis attribute will store the results of the startup
diagnostics. The first octet indicates the overall results
of the startup tests, while the remaining 8 octets will
contain the results of the individual test. Each octet
will contain a 1 if the test was passed, 2 if the test failed.
The following list defines the meanings of each octet in
the string: Octet 1 - overall test result
Octet 2 - system NMI test
Octet 3 - system timers test
Octet 4 - system DMA test
Octet 5 - 82586 test
Octet 6 - backplane ethernet address test
Octet 7 - NVRAM test
Octet 8 - dual port RAM test
Octet 9 - real time clock testro Enumeration .1.3.6.1.4.1.64.1.2.4 |
hubHealthTextThis attribute provides a textual description of which test,
if any, failed during diagnostics.ro DisplayString .1.3.6.1.4.1.64.1.2.5 |
hubHealthDataThis attribute provides a textual description of which test,
if any, failed during diagnostics.ro OCTET STRING .1.3.6.1.4.1.64.1.2.6 |
hubSystemResettingIndicates whether the hub is in the process of resetting
completely (coldstart).ro Enumeration .1.3.6.1.4.1.64.1.2.7 |
hubResettingIndicates whether the hub is in the process of resetting
or not (warmstart).ro Enumeration .1.3.6.1.4.1.64.1.2.8 |
hubExecutingSelfTestIndicates whether the hub is in the process of executing
self diagnostics.ro Enumeration .1.3.6.1.4.1.64.1.2.9 |
hubResetActionRestart the hub if selecting reset.rw Enumeration .1.3.6.1.4.1.64.1.2.10 |
hmPerfMonCapability OBJECT IDENTIFIER .1.3.6.1.4.1.64.1.3 |
hmPerfMonRelayTableThis table provide a management view individual
relay performance capability. SEQUENCE OF HmPerfMonRelayEntry .1.3.6.1.4.1.64.1.3.1 |
hmPerfMonRelayEntry HmPerfMonRelayEntry .1.3.6.1.4.1.64.1.3.1.1 |
relayPerfIDThis attribute is the value used in addressing the relay.ro INTEGER .1.3.6.1.4.1.64.1.3.1.1.1 |
relayTotalCollisionsThe counter is incremented every time the hub enters a condition
caused by simultaneous transmission and detection of external
activity on one or more of its ports.ro Counter .1.3.6.1.4.1.64.1.3.1.1.2 |
hmPerfMonPortTableThis table provide a management view of individual
ports performance capability. SEQUENCE OF HmPerfMonPortEntry .1.3.6.1.4.1.64.1.3.2 |
hmPerfMonPortEntry HmPerfMonPortEntry .1.3.6.1.4.1.64.1.3.2.1 |
gCardPerfIDThis attribute represent the card number and is used to address
the performance monitoring table.ro INTEGER .1.3.6.1.4.1.64.1.3.2.1.1 |
gPortPerfIDThis attribute represent the port number and is used to address
the performance monitoring table.ro INTEGER .1.3.6.1.4.1.64.1.3.2.1.2 |
gPortReadableFramesA representation of the total frames of legal length that have not
been corrupted in transmission counted by the port object.ro Counter .1.3.6.1.4.1.64.1.3.2.1.3 |
gPortReadableOctetsIt is sum of data and padding octets contained in ReadableFrames
counted by the port object.ro Counter .1.3.6.1.4.1.64.1.3.2.1.4 |
gPortPygmysThe sum of pygmy frame fragments counted by the port object.
They occur when a frame fragment was received which was not in
collision and was not recognized as a valid ethernet packet.
They normally make up less than 5% of Rx frames on hub-to-hub
or hub-to-backbone connections and < 1% of total Rx frames for hub-DTE
connections. Significantly higher levels may indicate external noise
hits on the cabling, i.e. UTP in a noisy environment.ro Counter .1.3.6.1.4.1.64.1.3.2.1.5 |
gPortRuntsThe sum of frames which were received then collided with
another fram(e)s received by the hub. The port(s) which
receive the collider frame(s) will increment their
gPortCollisions and the port which was collided with
will increment this counter. It is possible to
count more runts than collisions for a specific port.
As a rough guideline, less than 5% of the Rx frames
should be runts.ro Counter .1.3.6.1.4.1.64.1.3.2.1.6 |
gPortFrameCheckSeqErrsThe sum of frames received on this port that are an integral
number of octets in length and do not pass the FCS check.
Normally less than 1% of Rx frames. Could be caused by line
noise, loose connections, a faulty DTE, or a faulty hub.ro Counter .1.3.6.1.4.1.64.1.3.2.1.7 |
gPortAlignmentErrorsThe sum of frames received on this port that are not an
integral number of octets in length. Should be less than
1% of the total number of Rx frames and greater than or
equal to gPortFramesTooLong and gPortFrameCheckSeqErrors.
Could be caused by line noise, loose connections, a faulty
DTE, or a faulty hub.ro Counter .1.3.6.1.4.1.64.1.3.2.1.8 |
gPortFramesTooLongThe sum of frames received on this port that are more than
1518 octets long. Should be < 1% of the total number of Rx
frames. Could be caused by a faulty DTE or a faulty hub.ro Counter .1.3.6.1.4.1.64.1.3.2.1.9 |
gPortAutoPartitionCountIt is the number of times that this port has been automatically
partitioned.ro Counter .1.3.6.1.4.1.64.1.3.2.1.10 |
gPortLateCollisionsThis attribute is the total number of late collisions experienced
by the port object. Usually indicates a DTE trying to Tx w/o
checking the Ethernet for traffic first. May be due to a
hardware fault on the sending DTE, or a segment which is too long
for collision detection to work properly. Should normally be < 1%
of total Rx frames.ro Counter .1.3.6.1.4.1.64.1.3.2.1.11 |
gPortCollisionsThis attribute provides the total number of collisions encountered
by the port object. The port that was collided with will count a
runt. Normally less than 5% of the Rx frames should be collisions.
Numbers significantly higher than this may indicate hardware
problems or congestion.ro Counter .1.3.6.1.4.1.64.1.3.2.1.12 |
gPortAlarmsThe number of times a threshold was exceeded on that port.ro Counter .1.3.6.1.4.1.64.1.3.2.1.13 |
gPortMulticastFramesThis attribute contains a count of frames successfully received
by the port and are directed to an active non-broadcast group of
addresses.ro Counter .1.3.6.1.4.1.64.1.3.2.1.14 |
gPortBroadcastFramesThis attribute contains the total number of broadcast frames
received by the port object since system restart.ro Counter .1.3.6.1.4.1.64.1.3.2.1.15 |
hmAddrTrackCapability OBJECT IDENTIFIER .1.3.6.1.4.1.64.1.4 |
hmAddrTrackPortTableThis table provide a management view of individual
port address tracking capability. SEQUENCE OF HmAddrTrackPortEntry .1.3.6.1.4.1.64.1.4.1 |
hmAddrTrackPortEntry HmAddrTrackPortEntry .1.3.6.1.4.1.64.1.4.1.1 |
gCardAddrIDAn 8 bit value unique within the hub.ro INTEGER .1.3.6.1.4.1.64.1.4.1.1.1 |
gPortAddrIDAn 8 bit value unique within the group.ro INTEGER .1.3.6.1.4.1.64.1.4.1.1.2 |
gPortLastSourceAddressThe source (ethernet) address of the last ReadableFrame
received by this port.ro OCTET STRING .1.3.6.1.4.1.64.1.4.1.1.3 |
gPortSourceAddrChangesThis attribute counts the number of times the last source
address has changed.ro Counter .1.3.6.1.4.1.64.1.4.1.1.4 |
gandalf-bridge OBJECT IDENTIFIER .1.3.6.1.4.1.64.2 |
bridgeConfigObject OBJECT IDENTIFIER .1.3.6.1.4.1.64.2.1 |
bridgeBaseAddressThe MAC address used by this bridge when it must
be referred to in a unique fashion. It is
recommended that this be the numerically smallest
MAC address of all ports that belong to this
bridge. However it is only required to be unique.ro OCTET STRING .1.3.6.1.4.1.64.2.1.1 |
bridgeNumPortsThe number of (logical) ports controlled by this
bridging entity.ro INTEGER .1.3.6.1.4.1.64.2.1.2 |
bridgeTypeIndicates what type of bridging this bridge can
perform. If a bridge is actually performing a
certain type of bridging this will be indicated by
entries in the port table for the given type.ro Enumeration .1.3.6.1.4.1.64.2.1.3 |
bridgeNumOfInterfacesThe number of interfaces controlled by this bridging
entity, the interface stats are managed by MIB II
interface group.ro INTEGER .1.3.6.1.4.1.64.2.1.4 |
bridgePowerUpStatusThis attribute contains the result of any non fatal hardware
diagnostics performed during the power on procedure.ro Enumeration .1.3.6.1.4.1.64.2.1.5 |
bridgeIpAddrThis attribute contains the IP address of the bridge.ro NetworkAddress .1.3.6.1.4.1.64.2.1.6 |
bridgeManIDThis is a 24 bit value that identifies the manufacturer.ro OCTET STRING .1.3.6.1.4.1.64.2.1.7 |
bridgeManProductVersionThis attribute provides the software revision number.ro OCTET STRING .1.3.6.1.4.1.64.2.1.8 |
bridgeEEpromRevThis attribute provides the eeprom revision number and
is read from the hardware.ro OCTET STRING .1.3.6.1.4.1.64.2.1.9 |
bridgeSerialNumThis attribute provides the EBM Serial Number and
is read from the hardware.ro OCTET STRING .1.3.6.1.4.1.64.2.1.10 |
bridgeHubChassisThis attribute provides information on the type of
Hub Chassis this bridge is currently using.ro OCTET STRING .1.3.6.1.4.1.64.2.1.11 |
bridgeTpObject OBJECT IDENTIFIER .1.3.6.1.4.1.64.2.2 |
filterDatabaseSizeThis attribute represents the number of entries
into the filtering database.ro INTEGER .1.3.6.1.4.1.64.2.2.1 |
numberOfDynamicEntriesThis attribute contains a number of dynamic entries
currently in the Filtering Database.ro INTEGER .1.3.6.1.4.1.64.2.2.2 |
numberOfStaticEntriesThis attribute contains a number of static entries
currently in the Filtering Database.ro INTEGER .1.3.6.1.4.1.64.2.2.3 |
agingStateWhen this attribute is ON, the Bridge will age dynamic station
entries from the filter table automatically.ro Enumeration .1.3.6.1.4.1.64.2.2.4 |
agingTimeThe timeout period in seconds for aging out
dynamically learned forwarding information.ro INTEGER .1.3.6.1.4.1.64.2.2.5 |
learningStateWhen this attribute is ON, the Bridge will learn LAN station
addresses automatically.ro Enumeration .1.3.6.1.4.1.64.2.2.6 |
protocolFilterStateThis attribute specifies whether protocol filtering is enabled or
disabled.ro Enumeration .1.3.6.1.4.1.64.2.2.7 |
broadcastForwardingStateThis attribute specifies whether broadcast frames are being
forwarded.ro Enumeration .1.3.6.1.4.1.64.2.2.8 |
multicastForwardingStateThis attribute specifies whether multicast frames
are being forwarded.ro Enumeration .1.3.6.1.4.1.64.2.2.9 |
bridgeTpFdbTableA table that contains information about unicast
entries for which the bridge has forwarding and/or
filtering information. This information is used
by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF BridgeTpFdbEntry .1.3.6.1.4.1.64.2.2.10 |
bridgeTpFdbEntryInformation about a specific unicast MAC address
for which the bridge has some forwarding and/or
filtering information. BridgeTpFdbEntry .1.3.6.1.4.1.64.2.2.10.1 |
bridgeDot1dTpFdbAddressA unicast MAC address for which the bridge has
forwarding and/or filtering information.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.64.2.2.10.1.1 |
bridgeDot1dTpFdbPortEither the value '0', or the port number of the
port on which a frame having a source address
equal to the value of the corresponding instance
of dot1dTpFdbAddress has been seen. A value of
'0' indicates that the port number has not been
learned but that the bridge does have some
forwarding/filtering information about this
address (e.g. in the dot1dStaticTable).
Implementors are encouraged to assign the port
value to this object whenever it is learned even
for addresses for which the corresponding value of
dot1dTpFdbStatus is not learned(3).ro INTEGER .1.3.6.1.4.1.64.2.2.10.1.2 |
bridgeDot1dTpFdbStatusThe status of this entry. The meanings of the
values are:
other(1) : none of the following. This would
include the case where some other
MIB object (not the corresponding
instance of dot1dTpFdbPort, nor an
entry in the dot1dStaticTable) is
being used to determine if and how
frames addressed to the value of
the corresponding instance of
dot1dTpFdbAddress are being
forwarded.
invalid(2) : this entry is not longer valid
(e.g., it was learned but has since
aged-out), but has not yet been
flushed from the table.
learned(3) : the value of the corresponding
instance of dot1dTpFdbPort was
learned, and is being used.
self(4) : the value of the corresponding
instance of dot1dTpFdbAddress
represents one of the bridge's
addresses. The corresponding
instance of dot1dTpFdbPort
indicates which of the bridge's
ports has this address.
mgmt(5) : the value of the corresponding
instance of dot1dTpFdbAddress is
also the value of an existing
instance of dot1dStaticAddress.ro Enumeration .1.3.6.1.4.1.64.2.2.10.1.3 |
bridgeLogicalPortTableA table that contains information about every
port that is associated with this transparent
bridge.deprecated SEQUENCE OF BridgeLogicalPortEntry .1.3.6.1.4.1.64.2.2.11 |
bridgeLogicalPortEntryA list of information for each port of a
transparent bridge.deprecated BridgeLogicalPortEntry .1.3.6.1.4.1.64.2.2.11.1 |
bridgeDot1dTpPortThe port number of the port for which this entry
contains Transparent bridging management
information.rodeprecated INTEGER .1.3.6.1.4.1.64.2.2.11.1.1 |
bridgeDot1dTpPortMaxInfoThe maximum size of the INFO (non-MAC) field that
this port will receive or transmit.rodeprecated INTEGER .1.3.6.1.4.1.64.2.2.11.1.2 |
bridgeDot1dTpPortInFramesThe number of frames that have been received by
this port from its segment. Note that a frame
received on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function.rodeprecated Counter .1.3.6.1.4.1.64.2.2.11.1.3 |
bridgeDot1dTpPortOutFramesThe number of frames that have been transmitted
by this port to its segment. Note that a frame
transmitted on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function.rodeprecated Counter .1.3.6.1.4.1.64.2.2.11.1.4 |
bridgeDot1dTpPortInDiscardsCount of valid frames received which were
discarded (i.e., filtered) by the Forwarding
Process.rodeprecated Counter .1.3.6.1.4.1.64.2.2.11.1.5 |
bridgeStpObject OBJECT IDENTIFIER .1.3.6.1.4.1.64.2.3 |
bridgeDot1dStpProtocolSpecificationAn indication of what version of the Spanning
Tree Protocol is being run. The value
'decLb100(2)' indicates the DEC LANbridge 100
Spanning Tree protocol. IEEE 802.1d
implementations will return 'ieee8021d(3)'. If
future versions of the IEEE Spanning Tree Protocol
are released that are incompatible with the
current version a new value will be defined.rodeprecated Enumeration .1.3.6.1.4.1.64.2.3.1 |
bridgeDot1dStpPriorityThe value of the write-able portion of the Bridge
ID, i.e., the first two octets of the (8 octet
long) Bridge ID. The other (last) 6 octets of the
Bridge ID are given by the value of
dot1dBaseBridgeAddress.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.2 |
bridgeDot1dStpTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.rodeprecated TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.64.2.3.3 |
bridgeDot1dStpTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.rodeprecated Counter .1.3.6.1.4.1.64.2.3.4 |
bridgeDot1dStpDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.rodeprecated OCTET STRING .1.3.6.1.4.1.64.2.3.5 |
bridgeDot1dStpRootCostThe cost of the path to the root as seen from
this bridge.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.6 |
bridgeDot1dStpRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.7 |
bridgeDot1dStpMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.8 |
bridgeDot1dStpHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.9 |
bridgeDot1dStpHoldTimeThis time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.10 |
bridgeDot1dStpForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in a particular state before moving to the
next state. For example, how long a port stays in
the Listening state when moving from Blocking to
Learning. This value is also used, when a
topology change has been detected and is underway,
to age all dynamic entries in the Forwarding
Database. [Note that this value is the one that
this bridge is currently using, in contrast to
dot1dStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.11 |
bridgeDot1dStpBridgeMaxAgeThe value that all bridges use for MaxAge when
this bridge is acting as the root. Note that
802.1d/D9 specifies that the range for this
parameter is related to the value of
dot1dStpBridgeHelloTime. The granularity of this
timer is specified by 802.1d/D9 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.12 |
bridgeDot1dStpBridgeHelloTimeThe value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by
802.1d/D9 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.13 |
bridgeDot1dStpBridgeForwardDelayThe value that all bridges use for ForwardDelay
when this bridge is acting as the root. Note that
802.1d/D9 specifies that the range for this
parameter is related to the value of
dot1dStpBridgeMaxAge. The granularity of this
timer is specified by 802.1d/D9 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.14 |
bridgeStpPortTableA table that contains port-specific information
for the Spanning Tree Protocol.deprecated SEQUENCE OF BridgeStpPortEntry .1.3.6.1.4.1.64.2.3.15 |
bridgeStpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port.deprecated BridgeStpPortEntry .1.3.6.1.4.1.64.2.3.15.1 |
bridgeDot1dStpPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.15.1.1 |
bridgeDot1dStpPortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
dot1dStpPort.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.15.1.2 |
bridgeDot1dStpPortStateThe port's current state as defined by
application of the Spanning Tree Protocol. This
state controls what action a port takes on
reception of a frame. If the bridge has detected
a port that is malfunctioning it will place that
port into the broken(6) state. For ports which
are disabled (see dot1dStpPortEnable), this object
will have a value of disabled(1).rodeprecated Enumeration .1.3.6.1.4.1.64.2.3.15.1.3 |
bridgeDot1dStpPortEnableThe enabled/disabled status of the port.rodeprecated Enumeration .1.3.6.1.4.1.64.2.3.15.1.4 |
bridgeDot1dStpPortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.15.1.5 |
bridgeDot1dStpPortDesignatedRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.rodeprecated OCTET STRING .1.3.6.1.4.1.64.2.3.15.1.6 |
bridgeDot1dStpPortDesignatedCostThe path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.rodeprecated INTEGER .1.3.6.1.4.1.64.2.3.15.1.7 |
bridgeDot1dStpPortDesignatedBridgeThe Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.rodeprecated OCTET STRING .1.3.6.1.4.1.64.2.3.15.1.8 |
bridgeDot1dStpPortDesignatedPortThe Port Identifier of the port on the Designated
Bridge for this port's segment.rodeprecated OCTET STRING .1.3.6.1.4.1.64.2.3.15.1.9 |
bridgeDot1dStpPortForwardTransitionsThe number of times this port has transitioned
from the Learning state to the Forwarding state.rodeprecated Counter .1.3.6.1.4.1.64.2.3.15.1.10 |
bridgeStaticObject OBJECT IDENTIFIER .1.3.6.1.4.1.64.2.4 |
bridgeStaticTableA table containing filtering information
configured into the bridge by (local or network)
management specifying the set of ports to which
frames received from specific ports and containing
specific destination addresses are allowed to be
forwarded. The value of zero in this table as the
port number from which frames with a specific
destination address are received, is used to
specify all ports for which there is no specific
entry in this table for that particular
destination address. Entries are valid for
unicast and for group/broadcast addresses.deprecated SEQUENCE OF BridgeStaticEntry .1.3.6.1.4.1.64.2.4.1 |
bridgeStaticEntryFiltering information configured into the bridge
by (local or network) management specifying the
set of ports to which frames received from a
specific port and containing a specific
destination address are allowed to be forwarded.deprecated BridgeStaticEntry .1.3.6.1.4.1.64.2.4.1.1 |
bridgeDot1dStaticAddressThe destination MAC address in a frame to which
this entry's filtering information applies. This
object can take the value of a unicast address, a
group address or the broadcast address.rodeprecated PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.64.2.4.1.1.1 |
bridgeDot1dStaticReceivePortEither the value '0', or the port number of the
port from which a frame must be received in order
for this entry's filtering information to apply.
A value of zero indicates that this entry applies
on all ports of the bridge for which there is no
other applicable entry.rodeprecated INTEGER .1.3.6.1.4.1.64.2.4.1.1.2 |
bridgeDot1dStaticAllowedToGoToThis attribute contains a representation of
the Outbound Ports associated with this static entry.rodeprecated OCTET STRING .1.3.6.1.4.1.64.2.4.1.1.3 |
bridgeDot1dStaticStatusThis object indicates the status of this entry.
other(1) - this entry is currently in use but
the conditions under which it will
remain so are different from each of the
following values.
invalid(2) - writing this value to the object
removes the corresponding entry.
permanent(3) - this entry is currently in use
and will remain so after the next reset
of the bridge.
deleteOnReset(4) - this entry is currently in
use and will remain so until the next
reset of the bridge.
deleteOnTimeout(5) - this entry is currently
in use and will remain so until it is
aged out.rodeprecated Enumeration .1.3.6.1.4.1.64.2.4.1.1.4 |
bridgeProtFiltTableA table containing protocol filtering information
configured into the bridge by (local or network)
management specifying the set of ports to which
frames containing protocol ID are allowed to be
forwarded. SEQUENCE OF BridgeProtFiltEntry .1.3.6.1.4.1.64.2.4.2 |
bridgeProtFiltEntryProtocol filtering information configured into the
bridge by (local or network) management. BridgeProtFiltEntry .1.3.6.1.4.1.64.2.4.2.1 |
brProtFiltIndexThis attribute is used as a unique identifier into the Bridge
Protocol Filtering Table.ro INTEGER .1.3.6.1.4.1.64.2.4.2.1.1 |
brProtFiltNameA text string of up to 32 characters, of locally determined
significance used to identify this Protocol filter.ro OCTET STRING .1.3.6.1.4.1.64.2.4.2.1.2 |
brProtFiltIdThis attribute identifies the protocol type to be filtered.ro OCTET STRING .1.3.6.1.4.1.64.2.4.2.1.3 |
brProtFiltPortMapThis attribute contains a representation of
the Outbound Ports associated with this static entry.ro OCTET STRING .1.3.6.1.4.1.64.2.4.2.1.4 |
bridgeProtPriorityTableA table containing protocol priority information
configured into the bridge by (local or network)
management specifying the priority in which frames
will be transmitted on the wide area network links. SEQUENCE OF BridgeProtPriorityEntry .1.3.6.1.4.1.64.2.4.3 |
bridgeProtPriorityEntryProtocol priority information configured into the
bridge by (local or network) management. BridgeProtPriorityEntry .1.3.6.1.4.1.64.2.4.3.1 |
brProtPriorityIndexThis attribute is used as a unique identifier into the Bridge
Protocol Priority Table.ro INTEGER .1.3.6.1.4.1.64.2.4.3.1.1 |
brProtPriorityNameA text string of up to 32 characters, of locally determined
significance used to identify this Protocol Priority entry.ro OCTET STRING .1.3.6.1.4.1.64.2.4.3.1.2 |
brProtPriorityIdThis attribute identifies the protocol type to be prioritized.ro OCTET STRING .1.3.6.1.4.1.64.2.4.3.1.3 |
brProtPriorityLevelThe priority assigned to the associated Portocol IDro Enumeration .1.3.6.1.4.1.64.2.4.3.1.4 |
wanPhysicalObject OBJECT IDENTIFIER .1.3.6.1.4.1.64.2.5 |
wanPhysTableThis table represent a view of Management Facilities for
WAN physical ports. SEQUENCE OF WanPhysEntry .1.3.6.1.4.1.64.2.5.1 |
wanPhysEntryThis list contains counters and parameters related to the
management of WAN ports. WanPhysEntry .1.3.6.1.4.1.64.2.5.1.1 |
wanPhysPortIdThis attribute is used as a unique identifier for the Bridge
WAN interface.ro INTEGER .1.3.6.1.4.1.64.2.5.1.1.1 |
wanPhysPortNameA text string of up to 32 characters, of locally determined
significance used to identify this WAN interface.ro OCTET STRING .1.3.6.1.4.1.64.2.5.1.1.2 |
wanPhysLogicalPortThis attribute shows the logical port for this Wan interface.
Redundant links will have the same logical port.ro INTEGER .1.3.6.1.4.1.64.2.5.1.1.3 |
wanPhysDcdLevelThis attribute shows the level of the DCD EIA signal on this
particular WAN link.ro Enumeration .1.3.6.1.4.1.64.2.5.1.1.4 |
wanPhysLinkLevelThis attribute shows whether the WAN link is 'up' or 'down'.ro Enumeration .1.3.6.1.4.1.64.2.5.1.1.5 |
wanTxLinkUtilizationThis attribute shows the link utilization in the TX direction.
The utilization is a percentage of the bandwidth (0 to 100).ro Gauge .1.3.6.1.4.1.64.2.5.1.1.6 |
wanRxLinkUtilizationThis attribute shows the link utilization in the RX direction.
The utilization is a percentage of the bandwidth (0 to 100).ro Gauge .1.3.6.1.4.1.64.2.5.1.1.7 |
wanPhysFrameErrorsThis attribute shows the number of frame errors on this WAN
interface.ro INTEGER .1.3.6.1.4.1.64.2.5.1.1.8 |
wanCompressionStateThis attribute shows whether data compression is enabled
or disabled.ro Enumeration .1.3.6.1.4.1.64.2.5.1.1.9 |
wanCompressionRatioAn indication of how well the Bridge is compressing data that
is to be transmitted to another bridge. A value of 100 shows
no compression, a value of 300 shows a 3 : 1 compression.ro INTEGER .1.3.6.1.4.1.64.2.5.1.1.10 |
ieee8023Object OBJECT IDENTIFIER .1.3.6.1.4.1.64.2.6 |
ieeeIfTableThis table represent a view of Management Facilities for
the IEEE802.3 CSMA/CD MAC layer. The object was defined
by IEEE in a 802.3 standard. SEQUENCE OF IeeeIfEntry .1.3.6.1.4.1.64.2.6.1 |
ieeeIfEntryThis list contains counters and parameters related to the
management of the IEEE802.3 MAC layer. IeeeIfEntry .1.3.6.1.4.1.64.2.6.1.1 |
ieeeIfIndexThis attribute is used as a unique identifier for the Bridge
LAN interface.ro INTEGER .1.3.6.1.4.1.64.2.6.1.1.1 |
ieeeFrmsTxOkThis attribute contains a count of frames that are successfully
transmitted.ro Counter .1.3.6.1.4.1.64.2.6.1.1.2 |
ieeeSingleCollFrmsThis attribute contains a count of frames that are involved
in a single collision and are subsequently transmitted successfuly.ro Counter .1.3.6.1.4.1.64.2.6.1.1.3 |
ieeeMultipleCollFrmsThis attribute contains a count of frames that are involved
in more than one collision and are subsequently transmitted
successfully.ro Counter .1.3.6.1.4.1.64.2.6.1.1.4 |
ieeeOctetsTxOkThis attribute contains a count of data and padding octets
in frames that are successfully transmitted.ro Counter .1.3.6.1.4.1.64.2.6.1.1.5 |
ieeeDefTxThis attribute contains a count of frames whose transmission
was delayed on its first attempt becasue the medium was busy.ro Counter .1.3.6.1.4.1.64.2.6.1.1.6 |
ieeeMcastFrmsTxOkThis attribute contains a count of frames that are successfully
transmitted as indicated by the status value transmitOK, to a
group destination address other than broadcast.ro Counter .1.3.6.1.4.1.64.2.6.1.1.7 |
ieeeBcastFrmsTxOkThis attribute contains a number of broadcast frames transmitted
to the LAN connection.ro Counter .1.3.6.1.4.1.64.2.6.1.1.8 |
ieeeLateCollsThis attribute contains a count of the times that a collision
has been detected later than 512 bit times into the transmitted
packet.ro Counter .1.3.6.1.4.1.64.2.6.1.1.9 |
ieeeExcessCollsThis attribute contains a count of frames that due to excessive
collisions are not transmitted successfully.ro Counter .1.3.6.1.4.1.64.2.6.1.1.10 |
ieeeIntlMacTxErrorThis attribute contains a count of frames which would otherwise
be transmitted by the station,but could not be sent due to an
internal MAC sublayer transmit error.ro Counter .1.3.6.1.4.1.64.2.6.1.1.11 |
ieeeCsErrorsThis attribute contains number of frames that were lost because
the ethernet carrier signal was lost.ro Counter .1.3.6.1.4.1.64.2.6.1.1.12 |
ieeeExcessDefThis attribute contains a count of frames which deferred for
an excessive period of time.ro Counter .1.3.6.1.4.1.64.2.6.1.1.13 |
ieeeFrmsRxOkThis attribute contains a count of frames that are successfully
received.ro Counter .1.3.6.1.4.1.64.2.6.1.1.14 |
ieeeOctetsRxOkThis attribute contains a count of data and padding octets
in frames that are successfully received.ro Counter .1.3.6.1.4.1.64.2.6.1.1.15 |
ieeeMcastFrmsRxOkThis attribute contains a count of frames that are successfully
received and are directed to an active non-broadcast group of
addresses.ro Counter .1.3.6.1.4.1.64.2.6.1.1.16 |
ieeeBcastFrmsRxOkThis attribute contains a number of broadcast frames received
from the LAN connection.ro Counter .1.3.6.1.4.1.64.2.6.1.1.17 |
ieeeTooLongErrorsThis attribute contains a count of frames that are received
and exceeded the maximum permitted frame size. This counter
is incremented when the status of a frame reception is frame
TooLong.ro Counter .1.3.6.1.4.1.64.2.6.1.1.18 |
ieeeAlignErrorsThis attribute contains a count of frames that are not an
integral of octets in length and do not pass the Frame Check
Sequence(FCS) check.This counter is incremented when the
ReceiveStatus is reported as alignmentError.ro Counter .1.3.6.1.4.1.64.2.6.1.1.19 |
ieeeFcsErrorsThis attribute contains a count of frames that are an integral
of octets in length and do not pass the Frame Check Sequence(FCS)
check. This counter is incremented when the ReceiveStatus is
reported as frameCheckError.ro Counter .1.3.6.1.4.1.64.2.6.1.1.20 |
ieeeIrLengthErrorsThis attribute contains a count of frames with a length field
value, between the minimum unpadded LLC data size and the
maximum allowed LLC data size inclusive, that does not match
the number of LLC data octets received. The counter also
contains frames with a length field value less than the
minimum unpadded LLC data size.ro Counter .1.3.6.1.4.1.64.2.6.1.1.21 |
ieeeOorLengthFieldsThis attribute contains a count of frames with a length field
value greater than the maximum allowed LLC data size.ro Counter .1.3.6.1.4.1.64.2.6.1.1.22 |
ieeeIntlMacRcvErrorsThis attribute contains a count of frames which would otherwise
be received by the station,but could not be accepted due to an
internal MAC sublayer receive error.ro Counter .1.3.6.1.4.1.64.2.6.1.1.23 |
ieeeInitMacThis attributes indicates wether the underlying IEEE 802.3
MAC was initialized.ro Enumeration .1.3.6.1.4.1.64.2.6.1.1.24 |
ieeePromRxStatusThis attribute contains the current state of the Prom.ro Enumeration .1.3.6.1.4.1.64.2.6.1.1.25 |
ieeeMacSubLayerStatusThis attribute contains the current state of the Receive
side of the underlying IEEE 802.3 resource.ro Enumeration .1.3.6.1.4.1.64.2.6.1.1.26 |
ieeeTxStatusThis attribute contains the current state of the Transmit
side of the underlying IEEE 802.3 resource.ro Enumeration .1.3.6.1.4.1.64.2.6.1.1.27 |
ieeeMcastRxStatusThis attribute specifies if Multicast frames will be received
by the underlying IEEE 802.3 resource.ro Enumeration .1.3.6.1.4.1.64.2.6.1.1.28 |
ieeeMacAddressThis attribute contains the specific MAC Address of the
individual MAC Entity associated with the Port.ro OCTET STRING .1.3.6.1.4.1.64.2.6.1.1.29 |
ieeeSqeTestErrorsThis attribute contains a count of errors detected when
performing an SQE test. This counter is not currently supported.ro Counter .1.3.6.1.4.1.64.2.6.1.1.30 |
gandalf-generic OBJECT IDENTIFIER .1.3.6.1.4.1.64.3 |
gandalfLog OBJECT IDENTIFIER .1.3.6.1.4.1.64.3.1 |
ganEventLogTableA table containing alarm information. SEQUENCE OF GanEventLogEntry .1.3.6.1.4.1.64.3.1.1 |
ganEventLogEntryLog information of alarms generated by the product,
including time of event, severity and description. GanEventLogEntry .1.3.6.1.4.1.64.3.1.1.1 |
ganEventLogIndexAn index to the alarm table, not relevant other
than to display the table.ro INTEGER .1.3.6.1.4.1.64.3.1.1.1.1 |
ganEventLogDateThis date on which the event causing the alarm to be
generated occurred.ro OCTET STRING .1.3.6.1.4.1.64.3.1.1.1.2 |
ganEventLogTimeThis time at which the event causing the alarm to be
generated occurred.ro OCTET STRING .1.3.6.1.4.1.64.3.1.1.1.3 |
ganEventLogEventNumAn index to the alarm table, not relevant other
than to display the table. This attribute has
been deprecated because it duplicates the
ganEventLogIndex.rodeprecated INTEGER .1.3.6.1.4.1.64.3.1.1.1.4 |
ganEventLogSeverityAn index to the event log table, not relevant other
than to display the table.ro Enumeration .1.3.6.1.4.1.64.3.1.1.1.5 |
ganEventLogDescriptionTextual description of the event log.ro OCTET STRING .1.3.6.1.4.1.64.3.1.1.1.6 |
snmpAdminCapability OBJECT IDENTIFIER .1.3.6.1.4.1.64.3.2 |
snmpCommunityTableThis table provide a management view of which device
can poll this resource via SNMP based on the
Community Name, IP address and Privilege.
Sets are supported ONLY in the Gandalf WAN proxy agent.
To set a new community entry, use the instance 25
as the index value. Example: snmpCommunityName.25
Set all objects in the entry using instance 25. When
the last object is set, the agent checks for duplicate
entries and returns an error status if any found,
otherwise the new entry is inserted at the next
available position in the table.
Existing entries may be modified by setting the
a new value using an existing instance. The agent
rejects any attempt to duplicate an entry.
Objects may be deleted by setting the community name
to one or more spaces. The entry is deleted and any
vacated row is filled in by moving the last valid
row there.
NOTE: The object snmpTrapRemotePort is not supported
in the Gandalf WAN Proxy agent. SEQUENCE OF SnmpCommunityEntry .1.3.6.1.4.1.64.3.2.1 |
snmpCommunityEntryThis is a list of attributes that make the Community
Table. SnmpCommunityEntry .1.3.6.1.4.1.64.3.2.1.1 |
snmpCommunityIndexAn 8 bit value unique within the Community Name.ro INTEGER .1.3.6.1.4.1.64.3.2.1.1.1 |
snmpCommunityNameThe name of a Community supported by this SNMP agent.ro OCTET STRING .1.3.6.1.4.1.64.3.2.1.1.2 |
snmpCommunityIpAddrThe Ip Address of a manager associated with a Community
that will be supported by the SNMP agent. A value of
zero means that all managers from that Community will be
supported.ro IpAddress .1.3.6.1.4.1.64.3.2.1.1.3 |
snmpCommunityPrivThe access priviledge associated with a Community.ro Enumeration .1.3.6.1.4.1.64.3.2.1.1.4 |
snmpTrapCommunityTableThis table provide a management view of which device(s)
(i.e. LAN Managers) this resource will send Trap to.
Sets are supported ONLY in the Gandalf WAN proxy agent.
To set a new community entry, use the instance 25
as the index value. Example: snmpTrapCommunityName.25
Set all objects in the entry using instance 25. When
the last object is set, the agent checks for duplicate
entries and returns an error status if any found,
otherwise the new entry is inserted at the next
available position in the table.
Existing entries may be modified by setting the
a new value using an existing instance. The agent
rejects any attempt to duplicate an entry.
Objects may be deleted by setting the community name
to one or more spaces. The entry is deleted and any
vacated row is filled in by moving the last valid
row there. SEQUENCE OF SnmpTrapCommunityEntry .1.3.6.1.4.1.64.3.2.2 |
snmpTrapCommunityEntryThis is a list of attributes that make the Trap
Community Table. SnmpTrapCommunityEntry .1.3.6.1.4.1.64.3.2.2.1 |
snmpTrapCommunityIndexAn 8 bit value unique within the Community Name.ro INTEGER .1.3.6.1.4.1.64.3.2.2.1.1 |
snmpTrapCommunityNameThe name of a Trap Community associated with a LAN
Manager.ro OCTET STRING .1.3.6.1.4.1.64.3.2.2.1.2 |
snmpTrapIpAddrThe Ip Address of a manager that will receive Traps
generated by this SNMP agent.ro IpAddress .1.3.6.1.4.1.64.3.2.2.1.3 |
snmpTrapRemotePortThe remote UDP port number used by an agent to receive
Traps (usually port 162 is used).ro INTEGER .1.3.6.1.4.1.64.3.2.2.1.4 |
snmpTrapDescriptionThis attribute provide a description of Enterprise
Specific Traps. This is also known as the 'interesting
information' of an Enterprise Specific Trap.ro OCTET STRING .1.3.6.1.4.1.64.3.2.3 |
gandalf-2590 OBJECT IDENTIFIER .1.3.6.1.4.1.64.4 |
gandalf-wanNode OBJECT IDENTIFIER .1.3.6.1.4.1.64.5 |
gandalf-products OBJECT IDENTIFIER .1.3.6.1.4.1.64.6 |
gProd-wan OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.1 |
gProxy OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.1.1 |
g2300 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.1.2 |
g2050 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.1.3 |
gProd-hub OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.2 |
ecm1000 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.2.1 |
rsc9000 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.2.3 |
gProd-bridge OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3 |
lanline5220L OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.2 |
xbr6202 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.3 |
lanline5220e OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.4 |
lanline5225i OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.5 |
lanline5240i OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.6 |
xbr6204 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.7 |
lanline5221 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.8 |
lanline5242 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.3.9 |
gProd-gateway OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.4 |
wgm2590-hub OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.4.1 |
wgm2590-standalone OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.4.2 |
gProd-termserver OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.5 |
gts1000 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.5.1 |
gtsplus OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.5.2 |
gProd-router OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.6 |
lanline5250i OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.6.5 |
lanline5250L OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.6.7 |
lanline5242er OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.6.8 |
lanline5250fr OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.6.9 |
xpressway5250isdn-typ1 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.6.10 |
xpressway5250isdn-typ2 OBJECT IDENTIFIER .1.3.6.1.4.1.64.6.6.11 |
gandalf-nms OBJECT IDENTIFIER .1.3.6.1.4.1.64.7 |
gandalf-wanProxy OBJECT IDENTIFIER .1.3.6.1.4.1.64.8 |
gandalf-rlanisdn OBJECT IDENTIFIER .1.3.6.1.4.1.64.9 |
gandalf-termserver OBJECT IDENTIFIER .1.3.6.1.4.1.64.10 |
gandalf-router OBJECT IDENTIFIER .1.3.6.1.4.1.64.11 |
gandalf-experimental OBJECT IDENTIFIER .1.3.6.1.4.1.64.12 |