X25-OPT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
157
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
157 total| Object Name |
|---|
codex OBJECT IDENTIFIER .1.3.6.1.4.1.449 |
RFC1155-SMI Unknown .1.3.6.1.4.1.449 |
cdxProductSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.449.2 |
cdx6500 OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1 |
cdx6500Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2 |
cdx6500CfgProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1 |
cdx6500PCTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.1 |
cdx6500PPCTX25PortTableA table of X.25 Port configuration entries. SEQUENCE OF Cdx6500PPCTX25PortEntry .1.3.6.1.4.1.449.2.1.2.1.1.2 |
cdx6500PPCTX25PortEntryAn X.25 Configuration Table entry. Each entry
contains the configuration parameters for a single
X.25 port. Cdx6500PPCTX25PortEntry .1.3.6.1.4.1.449.2.1.2.1.1.2.1 |
cdx6500X25CfgPortNumberPort number for this X.25 port.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.1 |
cdx6500X25CfgConnTypeSpecify the control signal handshake and clocking
required for a connection to be made to this port:
simp - simple, no control signals required.
dtr - dedicated, require the data terminal ready
signal (DTR).
dtrd - same as DTR, except data set ready (DSR)
drops between calls.
dimo - port handshakes with attached dial modem
dimoa - same as DIMO except DSR never raised on
incoming call from modem.
dimob - same as DIMO except DSR follows DTR on
incoming call from modem.
dimov - port handshakes with attached V.25 bis
dial modem.
emri - port emulates a dial modem with ring
indicator (RI).
emdc - port emulates a dial modem with data carrier
detect (DCD).
simpv - SIMP/DIMOv, modem will switch from Leased
to Dial-only mode when leased line goes down
(used with Link Backup only).
simpb - simple, no control signals required for data
transmission and reception. By default output
leads will be low.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.2 |
cdx6500X25CfgPortContSpecify any of the following port control options:
NONE - no option specified.
MB - raise Pin 22 when the port becomes disabled.rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.3 |
cdx6500X25CfgClockSourceint - internal clock source.
ext - external clock source.
extint - internal receive and external transmit
clock source (DCE only).
extlp - external receive and loopback transmit
clock source (DTE only). extlp must be
configured in conjunction with extint.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.4 |
cdx6500X25CfgClockSpeedThis is the speed of the port in bits per second, when
using internal clocking. The highest available speed
is dependant on the card type, and on the interface type.
See the 6500 Series Configuration and Administration
Manual for proper values.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.5 |
cdx6500X25CfgAdmnInterfaceModeThe logical link address must be set to complementary
values in devices at each end of the link:
dte - link to have logical DTE address (A).
dce - link to have logical DCE address (B).
negotiate - link ends will negotiate which
end is DCE address (B). This option is available
only if the correct CSK is enabled.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.6 |
cdx6500X25CfgAdmnNumberPVCsNumber of logical channels used for Permanent Virtual
Circuits. The total number of PVC and SVC channels on
a link should be kept as small as possible and consistent
with needs. PVC connections must be configured in the
PVC Table.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.7 |
cdx6500X25CfgStartPVCChanNumThis is the starting logical channel number for the
Permanent Virtual Circuits on this link. Not used
if the number of PVCs = 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.8 |
cdx6500X25CfgNumberSVCsNumber of logical channels used in Switched Virtual
Circuits. The total number of PVC and SVC channels
on a link should be kept as small as possible and
consistent with needs.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.9 |
cdx6500X25CfgStartSVCChanNumThis is the starting logical channel number for the
Switched Virtual Circuits on this link. Not used if
the number of SVCs = 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.10 |
cdx6500X25CfgInitFrameSpecify the initial frame required by other end for link
startup:
none - do nothing (other end initiates link-up).
sabm - send SABM.
disc - send DISC, then SABM.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.11 |
cdx6500X25CfgT1RetryTimerT1 link retry timer value in tenths of a second
(e.g. 30 = 3.0 seconds).rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.12 |
cdx6500X25CfgT4PollTimerThis sets the time an idle link is probed for assurance
of connection to the remote device.
0 - disable the timer
X - X is in tenths of a second (e.g. 40 = 4.0 seconds)
and must be set greater than T1.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.13 |
cdx6500X25CfgN2TransTriesThe maximum number of attempts allowed to complete a
transmission.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.14 |
cdx6500X25CfgFrameSeqCountingPort uses normal or extended frame sequence numbering
norm - normal sequence counting (Modulo 8).
ext - extended sequencing (Modulo 128).rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.15 |
cdx6500X25CfgKFrameWindowFrame level window size must be set to the same value in
devices at each end of the link.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.16 |
cdx6500X25CfgAdmnPacketSequencingPort uses normal or extended packet level sequence
numbers :
norm - normal sequencing (Modulo 8).
ext - extended sequencing (Modulo 128).
The value must be the same in devices at each end of the
link.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.17 |
cdx6500X25CfgWPacketWindowPacket level window size must be set to the same value in
devices at each end of the link.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.18 |
cdx6500X25CfgPPacketSizeThis is the maximum packet size used on X.25 links. For
proper operation, the size must be the same in devices
at each end of the link.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.19 |
cdx6500X25CfgMaxNegotPacketSizeThis is the maximum negotiated packet size allowed for
inbound and outbound calls on this X.25 link.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.20 |
cdx6500X25CfgDataQueueUpperThis is the maximum number of data packets a channel on
this port will queue for transmission before invoking
flow control to the attached channelrw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.21 |
cdx6500X25CfgDataQueueLowerThis is the number of data packets a channel on this port
will have queued for transmission when it releases flow
control to the attached channelrw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.22 |
cdx6500X25CfgAdmnRestartTimerRestart-Request timeout timer in seconds. If timer
expires, request is sent again.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.23 |
cdx6500X25CfgAdmnResetTimerReset-Request timeout timer in seconds. If timer expires,
request is sent again.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.24 |
cdx6500X25CfgAdmnCallTimerCall-Request timeout timer in seconds. If timer expires,
call is cleared.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.25 |
cdx6500X25CfgAdmnClearTimerClear-Request timeout timer in seconds. If timer expires,
request is sent again.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.26 |
cdx6500X25CfgOutDelFacilitiesSpecify facilities deleted from an outbound call before
it is forwarded:
NONE - no facilities deleted.
THRO - delete throughput class negotiation.
NUI - delete network user identification.
CUG - delete closed user group.
Any combination of above specified by summing
(e.g. THRO+NUI. . .).rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.27 |
cdx6500X25CfgOutAddFacilitiesSpecify facilities added to an outbound call before it is
forwarded:
NONE - no facilities added.
REV - add reverse charging.
PACK - add packet size negotiation.
WIND - add window size negotiation.
Any combination of above specified by summing
(e.g. PACK+WIND+. . .).rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.28 |
cdx6500X25CfgOutBarFacilitiesSpecify facilities which, if present in an outbound call
will be blocked by the port:
NONE - no facility blocked.
REV - bar reverse charging.
FAST - bar fast select.
BCUG - bar Bilateral Closed User Group.
DGRAM - bar datagram.
Any combination of above specified by summing
(e.g. REV+FAST).rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.29 |
cdx6500X25CfgInBarFacilitiesSpecify facilities which, if present in an inbound call,
will be blocked by the port:
NONE - no facility blocked.
BCUG - bar Bilateral Closed User Group.
DGRAM - bar datagram.
REV - bar Reverse Charging.
Any combination of above specified by summing
(e.g. DGRAM+BCUG).rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.30 |
cdx6500X25CfgOptionsSelect options on this X.25 port as follows:
NONE - no option specified.
1980 - use X.25 1980.
NUI - perform network user identification validation check.
PDN - connected to Public Data Network.
CUD - use call user data subaddressing.
IBAR - bar all calls coming in from X.25 port user.
OBAR - bar all calls going out to X.25 port user.
CBCK - allow routing inbound calls back out this port.
CUG - check closed user group; otherwise, CUG passes
transparently.
CAUSE - pass cause, diagnostic, code in outbound
packets.
HOLD - hold calls over link restart.
NRST - do not send restart packet on link-up.
BKUP - this is a backup port to be activated if other
ports are down.
INL - inter-node link. Link goes to another Vanguard
device.INL may be a poor choice for high speed
links.INLB is set with INL to improve the
performance of high speed links.INLB can be configured in the
More X25 Options parameter.
INLA - set with INL option when an X.25 link
connection is to a 6500 node using 2.12.04 or
earlier.
DELAY - enable Delay and Path trace on this link (link
must connected to Rel. 4.xx node).
Any combination of above specified by summing
(e.g. 1980+NUI+. . .).rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.31 |
cdx6500X25CfgNumRoutDigitsThis specifies the number of routing digits in the call
user data. It is used on X.25 links attached to a Public
Data Network where the private network address is carried
in the call user data.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.32 |
cdx6500X25CfgPortDigitsToStripFor X.25 links connected to a Public Data Network, this
parameter specifies the number of prefix digits to
remove from the called address before forwarding the call
to the PDN.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.33 |
cdx6500X25CfgInDigitsToStripFor X.25 links connected to a Public Data Network, this
parameter specifies the number of prefix digits to remove
from the incoming calling address before forwarding the
call from the PDN.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.34 |
cdx6500X25CfgRestrictConnAll calls entering this port will be routed to the
destination specified in this parameter, irrespective of
route selection table entries. Blank this field to
disable this function.rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.35 |
cdx6500X25CfgPortAddressOn X.25 links:
If the X.25 Option REGO or REGI is selected, this
address is inserted into the calling address field of
the outbound or inbound call packet.
On MUX links:
When a MUX channel makes a call, the subaddress of the
channel is appended to this address and inserted into
the calling address field of the call packet.rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.36 |
cdx6500X25CfgCUGMemberThe port may be a member of up to 8 different Closed User
Groups (CUGs). Each CUG membership must be a two digit
number (except `
( e.g. 12,34,56,09,02,03 ).
`
00-99 - CUG Membership.rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.37 |
cdx6500X25CfgBillRecThis controls whether billing (accounting) records will
be created for calls on this port.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.38 |
cdx6500X25CfgSubAddrSizeFor ports connected to a Public Data Network, this
parameter specifies the number of digits in the
subaddress of an X.25 address.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.39 |
cdx6500X25CfgIdleDiscTimerThe time in seconds that the port must be idle (no calls)
before being automatically disconnected. A value of 0
disables the Idle Disconnect feature. This feature may
only be enabled on DIMO/DIMOa/DIMOb/DIMOv/SIMPv ports
with the BKUP option selected.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.40 |
cdx6500X25CfgCallSecurityFor ports used as V.25 bis backup, this parameter
specifies the type of call security to use prior to
the link being detected up :
disable - Disable will allow both incoming and
outgoing calls.
enable - Enable will allow ONLY outgoing calls.
Incoming calls will be immediately
terminated.
This parameter is only used with Link Backup.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.41 |
cdx6500X25CfgProtectLevelThis specifies the level of data or connection protection
which will be applied to calls to or from this port. The
actual level for a call will be negotiated to the lesser
of this level and the level configured for the other end
of the call :
none - No protection.
cpOnly - Connection protection only.
fullDcp - Full data and connection protection.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.42 |
cdx6500X25CfgReconnTimeoutThis specifies the number of seconds that DCP on the
originating side will wait between reconnection
attempts.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.43 |
cdx6500X25CfgReconnTriesLimitThis specifies the number of times that DCP on the
originating side will attempt to reconnect before
clearing the call. If 0 is entered, it will not
attempt to reconnect.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.44 |
cdx6500X25CfgFacilSubscripContNONE - Subscription to facilities not enforced.
FCN-ON - Flow Control Negotiation enabled.
Packet and Window size negotiation facilities
in an inbound call will be allowed. Packet
and Window size facilities will always be
included in outbound calls and call accepted/
connected when this parameter is set.
FCN-OFF - Flow Control Negotiation disabled.
Inbound calls containing Packet and Window
size facilities will be cleared. Packet
and Window size facilities will not be
present in outbound calls and call accepted/
connected when this parameter is set.
TCN-ON - Throughput Class Negotiation enabled.
The throughput class negotiation facility in
an inbound call will be allowed. The
throughput class negotiation facility will
always be included in outbound calls and
call accepted/connected when this parameter
is set. The facility is passed onward to the
destination in the call packet transparently
and does not alter the handling of the SVC
data within the node.
TCN-OFF - Throughput Class Negotiation disabled.
Inbound calls containing the throughput class
negotiation facility will be cleared. The
throughput class negotiation facility will
not be present in outbound calls and call
accepted/connected when this parameter is
set.
Some combinations of above options are allowed
(e.g. FCN-ON+TCN-ON).ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.45 |
cdx6500X25CfgAlarmPrioritySpecify the severity level of LINK UP and LINK DOWN alarms :
network - Severity HIGH alarms will be generated.
access - Severity LOW alarms will be generated.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.46 |
cdx6500X25CfgAddrTransSelect any of the following address translation options
NONE - no option specified
Outbound Call Processing:
DEDO - delete called address.
DEGO - delete calling address.
REGO - replace calling address with configured Port Address.
REGSO - replace calling address with configured Port
Address plus Inbound Subaddress obtained from
the Inbound Call Translation Table entry where
Private Network Address matches the entire
calling address.
INGO - replace calling address with configured Port
Address and retain original calling subaddress.
SAGO - strip calling address, but retain subaddress.
Inbound Call Processing:
INGI - replace calling address with configured Port
Address and retain original calling subaddress.
REGI - replace calling address with configured Port
Address.
SRGI - select route from the Calling Address
Translation Table by replacing the called
address with the Private Network Address
where the Inbound Calling Address matches
the beginning of the calling address.
Call Accept Processing:
DADA - delete called address in inbound/outbound
call accept.
DAGA - delete calling address in inbound/outbound
call accept.
IADD - copy called and calling addresses from call
request into outbound call accepted/connected.
Some of the options may be combined (e.g. DEDO+DEGO+...)rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.47 |
cdx6500X25CfgNumberInSVCsNumber of logical channels used in One Way Incoming
Switched Virtual Circuits. The total number of PVC,
One Way Incoming, One Way Outgoing and Two Way SVC
channels should be kept as small as possible and
consistent with needs.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.48 |
cdx6500X25CfgStartInSVCChanNumThis is the starting logical channel number for the One Way
Incoming Switched Virtual Circuits on this link.
Not used if the number of One Way Incoming SVCs = 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.49 |
cdx6500X25CfgNumberOutSVCsNumber of logical channels used in One Way Outgoing
Switched Virtual Circuits. The total number of PVC,
One Way Outgoing, One Way Outgoing and Two Way SVC
channels should be kept as small as possible and
consistent with needs.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.50 |
cdx6500X25CfgStartOutSVCChanNumThis is the starting logical channel number for the One Way
Outgoing Switched Virtual Circuits on this link.
Not used if the number of One Way Outgoing SVCs = 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.51 |
cdx6500X25CfgChargeInfoReqThis parameter specifies whether Charging Information
has to be sent even without requesting.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.52 |
cdx6500X25CfgVerfnTimerSpecify the NUI verification timer in seconds.
The call is cleared if timer expires.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.53 |
cdx6500X25CfgValdFailuresThe maximum number of successive NUI verification failures
an X.25 DTE can tolerate when making verification attempts
timer expires.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.2.1.54 |
cdx6500X25CfgActionTypeThis specifies the course of action to be taken if the NUI
violations exceed the configured threshold count.
This parameter is effective only if the X25 options parameter
is set to CNUI
NONE - No action is taken.
DISC - All connections on the port are broken.
DEGR - Port is busied-out for one minute then
it is re-enabled.
LOCK - All connections on the port are broken
and the port is disabled.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.55 |
cdx6500X25CfgLineIdleModeSpecify any of the following line idle mode options:
FLAG - Flag fill between frames
MARK - Mark idle between framesrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.56 |
cdx6500X25CfgConfOptionSelect any of the following conformance control options:
NONE - no option specified
CHKFAC - Checking of facility codes enabled.rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.57 |
cdx6500X25CfgInvertTxClkThis parameter specifies whether the phase of the transmit
clock should be inverted.
NO - Don't invert
YES - Invertrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.58 |
cdx6500X25CfgDimTypeSpecify the physical interface type to be used for this port:
V.36 - V.36 physical interface
EIA-530A - EIA-530A physical interface
V.35 - V.35 physical interface
X.21 - X.21 physical interface
RS-449 - RS-449 physical interface
EIA-530 - EIA-530 physical interface
RS-232 - RS-232 physical interfacerw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.59 |
cdx6500X25CfgMoreOptionsSelect more options on this X.25 port as follows:
NONE - no option specified
INLB - set with INL option to improve performance if
inter-node link is a high speed linkrw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.2.1.60 |
cdx6500X25CfgPsfFlagEnable or Disable Port Selection Facility feature.
Used to control access to ports for Select user group applications.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.61 |
cdx6500X25CfgElectricalInterfaceTypeSpecify the Electrical Interface Type:
V.24 - V.24 Electrical Interface Type
V.35 - V.35 Electrical Interface Type
V.36 - V.36 Electrical Interface Type
X.21 - X.21 Electrical Interface Type
NONE - Electrically disabledrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.62 |
cdx6500X25CfgV24ElectricalInterfaceOptionSpecify the Pin 22 option:
RI - V.24 uses Pin 22 for Ring Indicator output signal
TM - V.24 uses Pin 22 for Test Mode input signalrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.63 |
cdx6500X25CfgHighSpeedElectricalInterfaceOptionSpecify the cable type:
NONE - V.35/V.36/X.21 DCE with straight through cable
XOVER - V.35/V.36/X.21 DCE with crossover adapter cablerw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.2.1.64 |
cdx6500CfgGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.2 |
cdx6500CGTInboundCallTranTableAll of the configuration parameters relevant
to the Inbound Call Translation table. SEQUENCE OF Cdx6500CGTInboundCallTranEntry .1.3.6.1.4.1.449.2.1.2.2.2 |
cdx6500CGTInboundCallTranEntryA row of Inbound Call Translation configuration parameters. Cdx6500CGTInboundCallTranEntry .1.3.6.1.4.1.449.2.1.2.2.2.1 |
cdx6500InCallTranEntryNumThis is not a configuration parameter. Instead, it
identifies the particular Inbound Call Translation
Table entry being configured by the other parameters
in the record.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.2.1.1 |
cdx6500InCallTranInSubAddrThis is the subaddress contained in an inbound call
from another network, usually a public data network (PDN).
It will be translated into a private network address before
the call is forwarded.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.2.1.2 |
cdx6500InCallTranPrivNetAddrThis is the private network address to translate to,
before forwarding calls from a PDN.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.2.1.3 |
cdx6500CGTOutboundCallTranTableAll of the configuration parameters relevant
to the Outbound Call Translation table. SEQUENCE OF Cdx6500CGTOutboundCallTranEntry .1.3.6.1.4.1.449.2.1.2.2.3 |
cdx6500CGTOutboundCallTranEntryA row of Outbound Call Translation configuration parameters. Cdx6500CGTOutboundCallTranEntry .1.3.6.1.4.1.449.2.1.2.2.3.1 |
cdx6500OutCallTranEntryNumThis is not a configuration parameter. Instead, it
identifies the particular Outbound Call Translation
Table entry being configured by the other parameters
in the record.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.3.1.1 |
cdx6500OutCallTranPrivNetAddrThis is the private network address contained in an
outbound call to another network, usually a public
data network (PDN). It will be translated into a PDN
address before the call is forwarded.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.3.1.2 |
cdx6500OutCallTranOutNetAddrThis is the public network address to translate to,
before forwarding calls to a PDN.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.3.1.3 |
cdx6500OutCallTranOptionsThis parameter specifies options for outbound call address
translation as follows:
olda - insert the original called address into outbound
call user data.
newvalNone - same functionality as 'none', new enumeration
added for RFC1155 compatibility.rw Enumeration .1.3.6.1.4.1.449.2.1.2.2.3.1.4 |
cdx6500CGTCallingAddrTranTableAll of the configuration parameters relevant
to the Calling AddressTranslation table. SEQUENCE OF Cdx6500CGTCallingAddrTranEntry .1.3.6.1.4.1.449.2.1.2.2.13 |
cdx6500CGTCallingAddrTranEntryA row of Calling Address Translation configuration
parameters. Cdx6500CGTCallingAddrTranEntry .1.3.6.1.4.1.449.2.1.2.2.13.1 |
cdx6500CalladdrtranEntryNumThis is not a configuration parameter. Instead, it
identifies the entry being configured by the other
parameters in the record.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.13.1.1 |
cdx6500CalladdrtranInCallAddrThis is the calling address contained in an inbound call,
it will be translated into a private network address
(if a match is found in the Translation Table),
before the call is forwarded.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.13.1.2 |
cdx6500CalladdrtranPrivNetAddrThis is the private network address to translate to,
before forwarding the call.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.13.1.3 |
cdx6500CGTCudBaseAddrTranTableAll of the configuration parameters relevant
to the CUD Base AddressTranslation table. SEQUENCE OF Cdx6500CGTCudBaseAddrTranEntry .1.3.6.1.4.1.449.2.1.2.2.23 |
cdx6500CGTCudBaseAddrTranEntryA row of CUD Base Address Translation configuration
parameters. Cdx6500CGTCudBaseAddrTranEntry .1.3.6.1.4.1.449.2.1.2.2.23.1 |
cdx6500CudBaseaddrtranEntryNumThis is not a configuration parameter. Instead, it
identifies the entry being configured by the other
parameters in the record.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.23.1.1 |
cdx6500CudBaseStrEnter the sub-string to search in the CUD for the incoming
call for translating it into Called address.
For searching from index in the CUD the name can be
specified as (7)DADADIFUBBBB, it will skip 7 characters
of the CUD and match DADAIFUBBBB in the CUD starting
at Position 8.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.23.1.2 |
cdx6500CudBaseAddrEnter the X.25 Address which will be inserted for called
address of incoming X.25 call packet if the configured CUD
string is matched in the CUD of the incoming X.25 Call packet.rw DisplayString .1.3.6.1.4.1.449.2.1.2.2.23.1.3 |
cdx6500Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3 |
cdx6500StatProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1 |
cdx6500PSTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1.1 |
cdx6500PPSTX25PortTableA table of X.25 Port statistics. SEQUENCE OF Cdx6500PPSTX25PortEntry .1.3.6.1.4.1.449.2.1.3.1.1.2 |
cdx6500PPSTX25PortEntryAn X.25 Statistics Table entry. Each entry
contains the statistics for a single X.25
port. Cdx6500PPSTX25PortEntry .1.3.6.1.4.1.449.2.1.3.1.1.2.1 |
cdx6500X25StatPortNumberThe port number for this X.25 port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.1 |
cdx6500X25StatPortStatusStatus of this port :
Up - Port is active
Down - Port Is inactive
Disabled - An operator has disabled the port
Busy Out - an operator has busied out the portro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.2.1.2 |
cdx6500X25StatPortStatediscPhase - Disconnect Phase.
linkDisk - Link Disconnect.
linkSetup - The port is sending SABM frames and
waiting for a UA response.
sabmColl - SABM Collision.
frameReject - The port has rejected a received frame.
normal - The port sending/receiving data.
remoteBusy - The port is receiving RNR frames.
reset - The port is being reset.
sendRej - The port is sending REJ frames.
rbSr - The port is receiving RNR frames and
sending REJ frames.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.2.1.3 |
cdx6500X25StatActualPortSpeedThis is the speed of the port when Clock = INT; this is
the detected clock speed if Clock = EXT. If Port Speed
is 0, Clock = EXT, but clocking is not being received
fom attatched device.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.4 |
cdx6500X25StatPortUtilInPercentage of port bandwidth in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.5 |
cdx6500X25StatPortUtilOutPercentage of port bandwidth in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.6 |
cdx6500X25StatMaxSVCCountMaximum number of SVCs in use since last node, port or
statistics reset.ro Gauge .1.3.6.1.4.1.449.2.1.3.1.1.2.1.7 |
cdx6500X25StatCurrSVCCountCurrent number of SVCs in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.8 |
cdx6500X25StatInCharsNumber of characters received since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.9 |
cdx6500X25StatOutCharsNumber of characters sent since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.10 |
cdx6500X25StatInPktsNumber of packets received since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.11 |
cdx6500X25StatOutPktsNumber of packets sent since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.12 |
cdx6500X25StatInDataFramesNumber of frames received since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.13 |
cdx6500X25StatOutDataFramesNumber of frames sent since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.14 |
cdx6500X25StatNumPktsQueuedNumber of packets currently queued.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.15 |
cdx6500X25StatCharRateInSummary of the characters being received by the port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.16 |
cdx6500X25StatCharRateOutSummary of the characters being sent by the port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.17 |
cdx6500X25StatPktRateInSummary of the packets being received by the port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.18 |
cdx6500X25StatPktRateOutSummary of the packets being sent by the port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.19 |
cdx6500X25StatFrameRateInSummary of the frames being received by the port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.20 |
cdx6500X25StatFrameRateOutSummary of the frames being sent by the port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.21 |
cdx6500X25StatOverrunErrsNumber of Overrun errors since the last node or
statistics reset.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.2.1.22 |
cdx6500X25StatUnderrunErrsNumber of Underrun errors since the last node or
statistics reset.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.2.1.23 |
cdx6500X25StatCRCErrsNumber of CRC errors since the last node or
statistics reset.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.2.1.24 |
cdx6500X25StatInInfoFramesNumber of Info frames received since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.25 |
cdx6500X25StatOutInfoFramesNumber of Info frames sent since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.26 |
cdx6500X25StatInRNRFramesNumber of frames received since last node, port or
statistics reset indicating RNR.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.27 |
cdx6500X25StatOutRNRFramesNumber of frames sent since last node, port or
statistics reset indicating RNR.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.28 |
cdx6500X25StatInRRFramesNumber of frames received since last node, port or
statistics reset indicating RR.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.29 |
cdx6500X25StatOutRRFramesNumber of frames sent since last node, port or
statistics reset indicating RR.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.30 |
cdx6500X25StatInREJFramesNumber of frames received since last node, port or
statistics reset indicating REJ.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.31 |
cdx6500X25StatOutREJFramesNumber of frames sent since last node, port or
statistics reset indicating REJ.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.32 |
cdx6500X25StatInDataPktsNumber of data packets received since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.33 |
cdx6500X25StatOutDataPktsNumber of data packets sent since last node, port or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.2.1.34 |
cdx6500X25StatNumRxCallsSinceLastResetThe number of inbound calls that were attempted
since the last statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.35 |
cdx6500X25StatNumRxCallsRejectedThe number of inbound calls that were rejected
since the last statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.36 |
cdx6500X25StatRxLastCallFailureCauseThe reason the last inbound call was rejected,
since the last statistics reset.
The posssible values are:
notAvailable : Value not available if not
a (virtual) switched data
port.
noFailureReported : No call failure
noAvailableVirtualPort : No virtual port available
securityViolation : Password security failed
noResourcesAvailable : No resources available
callRejected : Call failed by Xircom card
invalidPhoneNumber : Phone number is incorrect
outgoingCallRequestTimeout : Outgoing call req timeout
callCollision : Call collision
virtualPortNotAvailable : This port is not available
invalidConfiguration : Configuration is incorrect
failureNotSupported : Failure is not supportedro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.2.1.37 |
cdx6500X25StatRxLastCalledNumberThe phone number of the virtual port of the last ISDN
call made into this port.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.2.1.38 |
cdx6500X25StatRxLastCallingNumberThe phone number of last party to make an ISDN
call into this port.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.2.1.39 |
cdx6500X25StatRxMinCallDurationThe minimum call duration of all inbound ISDN calls made
into this port, since the last statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.40 |
cdx6500X25StatRxMaxCallDurationThe maximum call duration of all inbound ISDN calls made
into this port, since the last statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.41 |
cdx6500X25StatRxAvgCallDurationThe average call duration of all inbound ISDN calls made
into this port, since the last statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.42 |
cdx6500X25StatNumTxCallsSinceLastResetThe number of outbound calls that were attempted
since the last statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.43 |
cdx6500X25StatNumTxCallsRejectedThe number of outbound calls that were rejected
since the last statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.44 |
cdx6500X25StatTxLastCallFailureCauseThe reason the last inbound call was rejected,
since the last statistics reset.
The posssible values are:
notAvailable : Value not available if not
a (virtual) switched data
port.
noFailureReported : No call failure
noAvailableVirtualPort : No virtual port available
securityViolation : Password security failed
noResourcesAvailable : No resources available
callRejected : Call failed by Xircom card
invalidPhoneNumber : Phone number is incorrect
outgoingCallRequestTimeout : Outgoing call req timeout
callCollision : Call collision
virtualPortNotAvailable : This port is not available
invalidConfiguration : Configuration is incorrect
failureNotSupported : Failure is not supportedro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.2.1.45 |
cdx6500X25StatTxLastCalledNumberThe phone number of the last ISDN call made by a virtual
port from this port.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.2.1.46 |
cdx6500X25StatTxLastCallingNumberThe phone number of the virtual port that made the last
ISDN call from this port.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.2.1.47 |
cdx6500X25StatTxMinCallDurationThe minimum call duration of all outbound ISDN calls made
from this port, since the last statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.48 |
cdx6500X25StatTxMaxCallDurationThe maximum call duration of all outbound ISDN calls made
from this port, since the last statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.49 |
cdx6500X25StatTxAvgCallDurationThe average call duration of all outbound ISDN calls made
from this port, since the last statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.50 |
cdx6500X25StatSignalingStateISDN call signaling state.
The possible values are:
idle : No ISDN call present.
ringing : Pending outgoing ISDN call request.
connected : ISDN call is connected.
congested : Congested mode.
disabled : Virtual Port is disabled.
dChannelDown : D-channel is down.
disabledChannelDown : Disable and D-channel is down.
disconnecting : Pending ISDN call disconnection.
notAvailable : Value not available if not a
(virtual) switched data port.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.2.1.51 |
cdx6500X25StatMaxPortUtilInMax percentage of port bandwidth in use since last
node, port or statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.52 |
cdx6500X25StatMaxPortUtilOutMax percentage of port bandwidth in use since last
node, port or statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.2.1.53 |
cdx6500X25StatMaxPortUtilInTimeTime stamp of Max percentage of port bandwidth in use
since last node, port or statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.54 |
cdx6500X25StatMaxPortUtilOutTimeTime stamp of Max percentage of port bandwidth in use
since last node, port or statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.55 |
cdx6500X25StatMaxSVCCountTimeTime stamp of Maximum number of SVCs in use since
last node, port or statistics reset.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.2.1.56 |
cdx6500Controls OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.4 |