WANSTATS-MIB
AI MIB Summary
The WANSTATS-MIB module enables SNMP-based monitoring of Remote Monitoring (RMON) media statistics specifically for Wide Area Network (WAN) links, tracking interface-level counters such as packet transmission/reception rates, error counts, and utilization metrics to facilitate performance analysis and fault isolation on WAN infrastructure.
The MIB containing RMON media statistics for WAN links.
Main OID:
wanStatsMIB.1.3.6.1.4.1.11.2.3.7.6.1.5.1.8
592
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
592 total| Object Name |
|---|
hp OBJECT IDENTIFIER .1.3.6.1.4.1.11 |
nm OBJECT IDENTIFIER .1.3.6.1.4.1.11.2 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3 |
netElement OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7 |
lanprobe OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6 |
general OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1 |
rmonExtension OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5 |
statsExtension OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1 |
wanStatsMIBThe MIB containing RMON media statistics for WAN links. MODULE-IDENTITY .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8 |
wanStatsMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1 |
wanSignalingStats OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1 |
wanT1E1StatsTableT1/E1 signaling statistics. SEQUENCE OF WanT1E1StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1 |
wanT1E1StatsEntryStatistics for a T1/E1 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanT1E1StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1 |
wanT1E1StatsIndexThe value of this object uniquely identifies this wanT1E1StatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.1 |
wanT1E1StatsDataSourceThis object identifies the source of the data that this wanT1E1StatsEntry analyzes. This source can be any DS1 or E1 interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be ds1(18).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.2 |
wanT1E1StatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.3 |
wanT1E1StatsInFramesThe total number of frames seen originating from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.4 |
wanT1E1StatsOutFramesThe total number of frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.5 |
wanT1E1StatsInOctetsThe sum of octets from all frames seen originating from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.6 |
wanT1E1StatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.7 |
wanT1E1StatsESsFor ESF and E1-CRC links an Errored Second is a second with one or more Path Code Violations OR one or more Out of Frame defects OR one or more Controlled Slip events OR a detected AIS defect. For D4 and E1-noCRC links, the presence of Bipolar Violations also triggers an Errored Second. This is not incremented during an Unavailable Second.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.8 |
wanT1E1StatsSESsA Severely Errored Second for ESF signals is a second with 320 or more Path Code Violation Error Events OR one or more Out of Frame defects OR a detected AIS defect. For E1-CRC signals, a Severely Errored Second is a second with 832 or more Path Code Violation error events OR one or more Out of Frame defects. For E1-noCRC signals, a Severely Errored Second is a 2048 LCVs or more. For D4 signals, a Severely Errored Second is a count of one-second intervals with Framing Error events, or an OOF defect, or 1544 LCVs or more. Controlled slips are not included in this parameter. This is not incremented during an Unavailable Second.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.9 |
wanT1E1StatsSEFSsAn Severely Errored Framing Second is a second with one or more Out of Frame defects OR a detected AIS defect.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.10 |
wanT1E1StatsOOFsAn OOF defect is the occurrence of a particular density of Framing Error events. For T1 links, an Out of Frame defect is declared when the receiver detects two or more framing errors within a 3 msec period for ESF signals and 0.75 msec for D4 signals, or two or more errors out of five or fewer consecutive framing-bits. For E1 links, an Out Of Frame defect is declared when three consecutive frame alignment signals have been received with an error (see G.706 Section 4.1 [17]). Once an Out Of Frame Defect is declared, the framer starts searching for a correct framing pattern. The Out of Frame defect ends when the signal is in frame. In-frame occurs when there are fewer than two frame bit errors within 3 msec period for ESF signals and 0.75 msec for D4 signals. For E1 links, in-frame occurs when a) in frame N the frame alignment signal is correct and b) in frame N+1 the frame alignment signal is absent (i.e., bit 2 in TS0 is a one) and c) in frame N+2 the frame alignment signal is present and correct.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.11 |
wanT1E1StatsUASsUnavailable Seconds (UAS) are calculated by counting the number of seconds that the interface is unavailable. The DS1 interface is said to be unavailable from the onset of 10 contiguous SESs, or the onset of the condition leading to a failure (see Failure States). If the condition leading to the failure was immediately preceded by one or more contiguous SESs, then the DS1 interface unavailability starts from the onset of these SESs. Once unavailable, and if no failure is present, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs. Once unavailable, and if a failure is present, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs, if the failure clearing time is less than or equal to 10 seconds. If the failure clearing time is more than 10 seconds, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs, or the onset period leading to the successful clearing condition, whichever occurs later. With respect to the DS1 error counts, all counters are incremented while the DS1 interface is deemed available. While the interface is deemed unavailable, the only count that is incremented is UASs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.12 |
wanT1E1StatsCSSsA Controlled Slip Second is a one-second interval containing one or more controlled slips.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.13 |
wanT1E1StatsPCVsA Path Coding Violation error event is a frame synchronization bit error in the D4 and E1-noCRC formats, or a CRC error in the ESF and E1-CRC formats.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.14 |
wanT1E1StatsLESsA Line Errored Second, according to T1M1.3, is a second in which one or more Line Code Violation error events were detected. While many implementations are currently unable to detect the zero strings, it is expected that interface manufacturers will add this capability in deference to ANSI; therefore, it will become available in time. In the T1M1.3 specification, near end Line Code Violations and far end Line Errored Seconds are counted. For consistency, we count Line Errored Seconds at both ends.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.15 |
wanT1E1StatsBESsA Bursty Errored Second (also known as Errored Second type B) is a second with fewer than 320 and more than 1 Path Coding Violation error events, no Severely Errored Frame defects and no detected incoming AIS defects. Controlled slips are not included in this parameter. This is not incremented during an Unavailable Second.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.16 |
wanT1E1StatsDMsA Degraded Minute is one in which the estimated error rate exceeds 1E-6 but does not exceed 1E-3 (see G.821 [15]). Degraded Minutes are determined by collecting all of the Available Seconds, removing any Severely Errored Seconds grouping the result in 60-second long groups and counting a 60-second long group (a.k.a., minute) as degraded if the cumulative errors during the seconds present in the group exceed 1E-6. Available seconds are merely those seconds which are not Unavailable as described below.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.17 |
wanT1E1StatsLCVsA Line Coding Violation (LCV) is the occurrence of either a Bipolar Violation (BPV) or Excessive Zeroes (EXZ) Error Event.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.18 |
wanT1E1StatsLOFsFor T1 links, the Loss Of Frame failure is declared when an OOF or LOS defect has persisted for T seconds, where 2 <= T <= 10. The Loss Of Frame failure is cleared when there have been no OOF or LOS defects during a period T where 0 <= T <= 20. Many systems will perform 'hit integration' within the period T before declaring or clearing the failure e.g., see TR 62411 [16]. For E1 links, the Loss Of Frame Failure is declared when an OOF defect is detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.19 |
wanT1E1StatsLOSsFor T1, the Loss Of Signal failure is declared upon observing 175 +/- 75 contiguous pulse positions with no pulses of either positive or negative polarity. The LOS failure is cleared upon observing an average pulse density of at least 12.5% over a period of 175 +/- 75 contiguous pulse positions starting with the receipt of a pulse. For E1 links, the Loss Of Signal failure is declared when greater than 10 consecutive zeroes are detected (see O.162 Section 3.4.4).ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.20 |
wanT1E1StatsRAIsThe Far End Alarm failure is also known as 'Yellow Alarm' in the T1 case and 'Distant Alarm' in the E1 case. For D4 links, the Far End Alarm failure is declared when bit 6 of all channels has been zero for at least 335 ms and is cleared when bit 6 of at least one channel is non-zero for a period T, where T is usually less than one second and always less than 5 seconds. The Far End Alarm failure is not declared for D4 links when a Loss of Signal is detected. For ESF links, the Far End Alarm failure is declared if the Yellow Alarm signal pattern occurs in at least seven out of ten contiguous 16-bit pattern intervals and is cleared if the Yellow Alarm signal pattern does not occur in ten contiguous 16-bit signal pattern intervals. For E1 links, the Far End Alarm failure is declared when bit 3 of time-slot zero is received set to one on two consecutive occasions. The Far End Alarm failure is cleared when bit 3 of time-slot zero is received set to zero.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.21 |
wanT1E1StatsAISsThe Alarm Indication Signal failure is declared when an AIS defect is detected at the input and the AIS defect still exists after the Loss Of Frame failure (which is caused by the unframed nature of the 'all-ones' signal) is declared. The AIS failure is cleared when the Loss Of Frame failure is cleared.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.22 |
wanT1E1StatsTS16AISsFor E1 links, the TS16 Alarm Indication Signal failure is declared when time-slot 16 is received as all ones for all frames of two consecutive multiframes (see G.732 Section 4.2.6). This condition is never declared for T1.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.23 |
wanT1E1StatsLOMFsThe Loss Of MultiFrame failure is declared when two consecutive multiframe alignment signals (bits 4 through 7 of TS16 of frame 0) have been received with an error. The Loss Of Multiframe failure is cleared when the first correct multiframe alignment signal is received. The Loss Of Multiframe failure can only be declared for E1 links operating with G.732 [18] framing (sometimes called 'Channel Associated Signalling' mode).ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.24 |
wanT1E1StatsFarLOMFsThe Far End Loss Of Multiframe failure is declared when bit 2 of TS16 of frame 0 is received set to one on two consecutive occasions. The Far End Loss Of Multiframe failure is cleared when bit 2 of TS16 of frame 0 is received set to zero. The Far End Loss Of Multiframe failure can only be declared for E1 links operating in 'Channel Associated Signalling' mode.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.25 |
wanT1E1StatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.26 |
wanT1E1StatsStatusThe status of this wanT1E1StatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.27 |
wanVSeriesStatsTableV-series interface statistics. SEQUENCE OF WanVSeriesStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2 |
wanVSeriesStatsEntryThe statistics for a V-series interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanVSeriesStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1 |
wanVSeriesStatsIndexThe value of this object uniquely identifies this wanVSeriesStatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.1 |
wanVSeriesStatsDataSourceThis object identifies the source of the data that this wanVSeriesStatsEntry analyzes. This source can be and V-series interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be rs232(33) , v35(45), v11(64), or v36(65).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.2 |
wanVSeriesStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.3 |
wanVSeriesStatsInFramesThe total number of frames seen originating from the far end of the link including errored.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.4 |
wanVSeriesStatsOutFramesThe total number of frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.5 |
wanVSeriesStatsInOctetsThe sum of octets from all frames seen originating from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.6 |
wanVSeriesStatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.7 |
wanVSeriesStatsInFCSsTotal number of frames with an invalid frame check from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.8 |
wanVSeriesStatsOutFCSsTotal number of frames with an invalid frame check from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.9 |
wanVSeriesStatsInOverrunsTotal number of frames from the far end of the link that failed to be received because the receiver did not accept the data in time.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.10 |
wanVSeriesStatsOutOverrunsTotal number of frames from the near end of the link that failed to be received because the receiver did not accept the data in time.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.11 |
wanVSeriesStatsInterruptedFramesTotal number of frames that failed to be received or transmitted on the port due to loss of modem signals.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.12 |
wanVSeriesStatsInAbortedFramesNumber of frames from the far end of the link aborted on the port due to receiving an abort sequence.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.13 |
wanVSeriesStatsOutAbortedFramesNumber of frames from the near end of the link aborted on the port due to receiving an abort sequence.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.14 |
wanVSeriesStatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.15 |
wanVSeriesStatsStatusThe status of this wanVSeriesStatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.16 |
wanHssiStatsTableHSSI interface statistics.deprecated SEQUENCE OF WanHssiStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3 |
wanHssiStatsEntryThe statistics for a HSSI interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.deprecated WanHssiStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1 |
wanHssiStatsIndexThe value of this object uniquely identifies this wanHssiStatsTable entry.deprecated INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.1 |
wanHssiStatsDataSourceThis object identifies the source of the data that this wanT1E1StatsEntry analyzes. This source can be any HSSI interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be hssi(46).rwdeprecated OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.2 |
wanHssiStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.3 |
wanHssiStatsInFramesThe total number of frames seen originating from the far end of the link including errored frames.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.4 |
wanHssiStatsOutFramesThe total number of frames seen originating from the near end of the link including errored frames.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.5 |
wanHssiStatsInOctetsThe sum of octets from all frames seen originating from the far end of the link including errored frames.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.6 |
wanHssiStatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link including errored frames.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.7 |
wanHssiStatsRxLongFramesNumber of long frames from the far end of the link.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.8 |
wanHssiStatsRxCrcErrorsNumber of frames from far end of link with CRC errors.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.9 |
wanHssiStatsRxOverrunsNumber of frames from far end of link with FIFO overrun errors.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.10 |
wanHssiStatsRxAbortsNumber of frames from far end of link with abort status.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.11 |
wanHssiStatsTxAbortsNumber of frames from near end of link with internal abort errors.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.12 |
wanHssiStatsTxUnderrunsNumber of frames from near end of link aborted with underrun errors.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.13 |
wanHssiStatsRxRingErrorsNumber of receive ring error events.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.14 |
wanHssiStatsRxRingOverrunsNumber of receive ring overrun events.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.15 |
wanHssiStatsTxRingErrorsNumber of transmit ring error events.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.16 |
wanHssiStatsPortOpErrorsNumber of port operation error events.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.17 |
wanHssiStatsTxCmplProcessingsNumber of transmit complete processings (TINT).rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.18 |
wanHssiStatsOwnerThe entity that configured this entry.rwdeprecated OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.19 |
wanHssiStatsStatusThe status of this wanHssiStatsTable entry.rwdeprecated RowStatus (SNMPv2-TC) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.20 |
wanT3E3StatsTableT3/E3 signaling statistics SEQUENCE OF WanT3E3StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4 |
wanT3E3StatsEntryStatistics for a T3/E3 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanT3E3StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1 |
wanT3E3StatsIndexThe value of this object uniquely identifies this wanT3E3StatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.1 |
wanT3E3StatsDataSourceThis object identifies the source of the data that this wanT3E3StatsEntry analyzes. This source can be any DS3 or E3 interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value of the associated ifIndex can only be ds3(30).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.2 |
wanT3E3StatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.3 |
wanT3E3StatsInFramesThe total number of frames seen originating from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.4 |
wanT3E3StatsOutFramesThe total number of frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.5 |
wanT3E3StatsInOctetsThe sum of octets from all frames seen originating from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.6 |
wanT3E3StatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.7 |
wanT3E3StatsPESsA PES is a second with one or more PCVs OR one or more Out of Frame defects OR a detected incoming AIS. This gauge is not incremented when UASs are counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.8 |
wanT3E3StatsPSESsA PSES is a second with 44 or more PCVs OR one or more Out of Frame defects OR a detected incoming AIS. This gauge is not incremented when UASs are counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.9 |
wanT3E3StatsOOFsA DS3 OOF defect is detected when any three or more errors in sixteen or fewer consecutive F-bits occur within a DS3 M-frame. An OOF defect may also be called a Severely Errored Frame (SEF) defect. An OOF defect is cleared when reframe occurs. A DS3 Loss of Frame (LOF) failure is declared when the DS3 OOF defect is consistent for 2 to 10 seconds. The DS3 OOF defect ends when reframe occurs. The DS3 LOF failure is cleared when the DS3 OOF defect is absent for 10 to 20 seconds. An E3 OOF defect is detected when four consecutive frame alignment signals have been incorrectly received in there predicted positions in an E3 signal. E3 frame alignment occurs when the presence of three consecutive frame alignment signals have been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.10 |
wanT3E3StatsSEFSsA SEFS is a second with one or more Out of Frame defects OR a detected incoming AIS.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.11 |
wanT3E3StatsUASsUAS are calculated by counting the number of seconds that the interface is unavailable. The DS3 interface is said to be unavailable from the onset of 10 contiguous PSESs, or the onset of the condition leading to a failure (see Failure States). If the condition leading to the failure was immediately preceded by one or more contiguous PSESs, then the DS3 interface unavailability starts from the onset of these PSESs. Once unavailable, and if no failure is present, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs. Once unavailable, and if a failure is present, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs, if the failure clearing time is less than or equal to 10 seconds. If the failure clearing time is more than 10 seconds, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs, or the onset period leading to the successful clearing condition, whichever occurs later. With respect to the DS3 error counts, all counters are incremented while the DS3 interface is deemed available. While the interface is deemed unavailable, the only count that is incremented is UASs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.12 |
wanT3E3StatsLCVsThis parameter is a count of both BPVs and EXZs occurring over the accumulation period. An EXZ increments the LCV by one regardless of the length of the zero string.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.13 |
wanT3E3StatsPCVsFor all DS3 applications, a coding violation error event is a P-bit Parity Error event. A P-bit Parity Error event is the occurrence of a received P-bit code on the DS3 M-frame that is not identical to the corresponding locally- calculated code.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.14 |
wanT3E3StatsLESsA Line Errored Second is a second in which one or more CVs occurred OR one or more LOS defects.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.15 |
wanT3E3StatsCCVsFor C-bit Parity and SYNTRAN DS3 applications, this is the count of coding violations reported via the C-bits. For C-bit Parity, it is a count of CP-bit parity errors occurring in the accumulation interval. For SYNTRAN, it is a count of CRC-9 errors occurring in the accumulation interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.16 |
wanT3E3StatsCESsAn CES is a second with one or more CCVs OR one or more Out of Frame defects OR a detected incoming AIS. This count is only for the SYNTRAN and C-bit Parity DS3 applications. This gauge is not incremented when UASs are counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.17 |
wanT3E3StatsCSESsA CSES is a second with 44 or more CCVs OR one or more Out of Frame defects OR a detected incoming AIS. This count is only for the SYNTRAN and C-bit Parity DS3 applications. This gauge is not incremented when UASs are counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.18 |
wanT3E3StatsRAIsThe Remote Alarm Indication (RAI) failure, in SYNTRAN applications, is declared after detecting the Yellow Alarm Signal on the alarm channel. See ANSI T1.107a-1990 [10]. The Remote Alarm Indication failure, in C-bit Parity DS3 applications, is declared as soon as the preqsence of either one or two alarm signals are detected on then Far End Alarm Channel. See [10]. The Remote Alarm Indication failure may also be declared after detecting the far-end SEF/AIS defect (aka yellow). The Remote Alarm Indication failure is cleared as soon as the presence of the any of the above alarms are removed. Also, the incoming failure state is declared when a defect persists for at least 2-10 seconds. The defects are the following: Loss of Signal (LOS), an Out of Frame (OOF) or an incoming Alarm Indication Signal (AIS). The Failure State is cleared when the defect is absent for less than or equal to 20 seconds.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.19 |
wanT3E3StatsAISsThe DS3 AIS is framed with 'stuck stuffing.' This implies that it has a valid M-subframe alignments bits, M-frame alignment bits, and P bits. The information bits are set to a 1010... sequence, starting with a one (1) after each M-subframe alignment bit, M-frame alignment bit, X bit, P bit, and C bit. The C bits are all set to zero giving what is called 'stuck stuffing.' The X bits are set to one. The DS3 AIS defect is declared after DS3 AIS is present in contiguous M-frames for a time equal to or greater than T, where 0.2 ms <= T <= 100 ms. The DS3 AIS defect is terminated after AIS is absent in contiguous M-frames for a time equal to or greater than T. The E3 binary content of the AIS is nominally a continuous stream of ones. AIS detection and the application of consequent actions, should be completed within a time limit of 1 ms.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.20 |
wanT3E3StatsLOFsA DS3 Loss of Frame (LOF) failure is declared when the DS3 OOF defect is consistent for 2 to 10 seconds. The DS3 OOF defect ends when reframe occurs. The DS3 LOF failure is cleared when the DS3 OOF defect is absent for 10 to 20 seconds. (See T1.231 section 7.1.2.2.1)ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.21 |
wanT3E3StatsLOSsThe DS3 LOS defect is declared upon observing 175 +/- 75 contiguous pulse positions with no pulses of either positive or negative polarity. The DS3 LOS defect is terminated upon observing an average pulse density of at least 33% over a period of 175 +/- 75 contiguous pulse positions starting with the receipt of a pulse.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.22 |
wanT3E3StatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.23 |
wanT3E3StatsStatusThe status of this wanT3E3StatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.24 |
wanAtmStatsTableATM signaling statistics. SEQUENCE OF WanAtmStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5 |
wanAtmStatsEntryThe statistics for an ATM interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanAtmStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1 |
wanAtmStatsIndexThe value of this object uniquely identifies this wanAtmStatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.1 |
wanAtmStatsDataSourceThis object identifies the source of the data that this wanAtmStatsEntry analyzes. This source can be any interface on this device. in order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be atm(37).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.2 |
wanAtmStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.3 |
wanAtmStatsInCellsThe total number of cells seen coming from the far end of the link including errored cells.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.4 |
wanAtmStatsOutCellsThe total number of cells seen coming from the near end of the link including errored cells.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.5 |
wanAtmStatsInCLP1The total number of cells with the CLP bit set seen coming from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.6 |
wanAtmStatsOutCLP1The total number of cells with the CLP bit set seen coming from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.7 |
wanAtmStatsConnectionEventsThis counter counts the sum of the following errors: 1) SSCOP Connection Disconnect Counter The abnormal occurrence of this event is characterized by the expiry of Timer_NO_RESPONSE. (This event is communicated to the layer management with MAA-ERROR code P. See ITU-T Q.2110.) 2) SSCOP Connection Initiation Failure This condition indicates the inability to establish an SSCOP connection. This event occurs whenever the number of expiries of the connection control timer (Timer_CC) exceeds the MaxCC or upon receipt of a connection reject message BGREJ PDU. (This event is communicated to layer management with MAA-ERROR code O. See ITU-T Q.2110.) 3) SSCOP Connection Re-Establ/Resynch This event occurs upon receipt of a BGN PDU or RESYNC PDU.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.8 |
wanAtmStatsErroredPDUsThis counter counts the sum of the following errors: 1) Invalid PDUs. These are defined in SSCOP and consist of PDUs with incorrect length (MAA-ERROR code U), undefined PDU type code or not 32-bit aligned. 2) PDUs that result in MAA error codes and are discarded See Errors A-M and Q-T defined in ITU-T Q.2110.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.9 |
wanAtmStatsSetupAttemptsThis counter counts the number of call setup attempts (both successful and unsuccessful) detected on this interface.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.10 |
wanAtmStatsInRoutesUnavailableThis counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 1 unallocated (unassigned) number 2 no route to specified transit network 3 no route to destination 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.11 |
wanAtmStatsOutRoutesUnavailableThis counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 1 unallocated (unassigned) number 2 no route to specified transit network 3 no route to destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.12 |
wanAtmStatsInResourcesUnavailableThis counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated): Cause Value Meaning 35 requested VPCI/VCI not available 37 user cell rate not available (UNI3.1 only) 38 network out of order 41 temporary failure 45 no VPCI/VCI available 47 resource unavailable, unspecified 49 Quality of Service unavailable 51 user cell rate not available (UNI3.0 only) 58 bearer capability not presently available 63 Service or option not available, unspecified 92 too many pending add party requests NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.13 |
wanAtmStatsOutResourcesUnavailableThis counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated): Cause Value Meaning 35 requested VPCI/VCI not available 37 user cell rate not available (UNI3.1 only) 38 network out of order 41 temporary failure 45 no VPCI/VCI available 47 resource unavailable, unspecified 49 Quality of Service unavailable 51 user cell rate not available (UNI3.0 only) 58 bearer capability not presently available 63 Service or option not available, unspecified 92 too many pending add party requests NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.14 |
wanAtmStatsInUnsuccessfulCallsThis counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction 27 destination out of order 31 normal, unspecified 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted. Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.15 |
wanAtmStatsOutUnsuccessfulCallsThis counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction (CLIR) 27 destination out of order 31 normal, unspecified 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted. Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.16 |
wanAtmStatsInIncorrectMsgsThe Incorrect Messages Counter reflects any sort of incorrect information in a message. This includes: ? RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, and STATUS messages transmitted or received, that contain any of the Cause values listed below. ? Ignored messages. These messages are dropped because the message was so damaged that it could not be further processed. A list of dropped messages is compiled below: Message with invalid protocol discriminator Message with errors in the call reference I.E. ? Bits 5-8 of the first octet not equal to '0000' ? Bits 1-4 of the first octet indicating a length other than 3 octets ? RELEASE COMPLETE message received with a call reference that does not relate to a call active or in progress ? SETUP message received with call reference flag incorrectly set to 1 ? SETUP message received with a call reference for a call that is already active or in progress. Message too short The following cause values are monitored by this counter (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated) Cause Value Meaning 10 VPCI/VCI unacceptable (UNI3.0 only) 36 VPCI/VCI assignment failure (UNI3.1 only) 81 invalid call reference value 82 identified channel does not exist 89 invalid endpoint reference 96 mandatory information element is missing 97 message type non-existent or not implemented 99 information element non-existent or not implemented 100 invalid information element contents 101 message not compatible with call state 104 incorrect message length 111 protocol error, unspecified NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.17 |
wanAtmStatsOutIncorrectMsgsThe Incorrect Messages Counter reflects any sort of incorrect information in a message. This includes: ? RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, and STATUS messages transmitted or received, that contain any of the Cause values listed below. ? Ignored messages. These messages are dropped because the message was so damaged that it could not be further processed. A list of dropped messages is compiled below: Message with invalid protocol discriminator Message with errors in the call reference I.E. ? Bits 5-8 of the first octet not equal to '0000' ? Bits 1-4 of the first octet indicating a length other than 3 octets ? RELEASE COMPLETE message received with a call reference that does not relate to a call active or in progress ? SETUP message received with call reference flag incorrectly set to 1 ? SETUP message received with a call reference for a call that is already active or in progress. Message too short The following cause values are monitored by this counter Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated) Cause Value Meaning 10 VPCI/VCI unacceptable (UNI3.0 only) 36 VPCI/VCI assignment failure (UNI3.1 only) 81 invalid call reference value 82 identified channel does not exist 89 invalid endpoint reference 96 mandatory information element is missing 97 message type non-existent or not implemented 99 information element non-existent or not implemented 100 invalid information element contents 101 message not compatible with call state 104 incorrect message length 111 protocol error, unspecified NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.18 |
wanAtmStatsInPartyEventsThis counter monitors error events that occur due to the originating user doing something wrong. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 78 AAL parameters cannot be supported (UNI3.1 only) 91 invalid transit network selection 93 AAL parameters cannot be supported (UNI3.0 only) NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.19 |
wanAtmStatsOutPartyEventsThis counter monitors error events that occur due to the originating user doing something wrong. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 78 AAL parameters cannot be supported (UNI3.1 only) 91 invalid transit network selection 93 AAL parameters cannot be supported (UNI3.0 only) NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.20 |
wanAtmStatsInExpiriesThe Timer Expiries Counter provides a count of network timer expiries, and to some extent, host or switch timer expiries. The conditions for incrementing this counter are: ? Expiry of any network timer ? Receipt of a RELEASE or RELEASE COMPLETE message with Cause #102, 'recovery on timer expiry'. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.21 |
wanAtmStatsOutExpiriesThe Timer Expiries Counter provides a count of network timer expiries, and to some extent, host or switch timer expiries. The conditions for incrementing this counter are: ? Expiry of any network timer ? Receipt of a RELEASE or RELEASE COMPLETE message with Cause #102, 'recovery on timer expiry'. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.22 |
wanAtmStatsInRestartErrorsThe Restart Activity Counter provides a count of host, switch, or network restart activity. This counter is incremented when receiving a RESTART message.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.23 |
wanAtmStatsOutRestartErrorsThe Restart Activity Counter provides a count of host, switch, or network restart activity. This counter is incremented when transmitting a RESTART message.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.24 |
wanAtmStatsInSVCsSVC VCCs established at this signaling entity for incoming connections.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.25 |
wanAtmStatsOutSVCsSVC VCCs established at this signaling entity for outgoing connections.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.26 |
wanAtmStatsInOCDsAn out of cell delineation from far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.27 |
wanAtmStatsOutOCDsAn out of cell delineation from near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.28 |
wanAtmStatsInLOCsA loss of cell delineation error from far end of the link. This is a persistent OCD condition.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.29 |
wanAtmStatsOutLOCsA loss of cell delineation error from near end of link. This is a persistent OCD condition.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.30 |
wanAtmStatsInLOFsA loss of frame error from far end of link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.31 |
wanAtmStatsOutLOFsA loss of frame error from near end of link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.32 |
wanAtmStatsInLOPsA loss of pointer error from far end of link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.33 |
wanAtmStatsOutLOPsA loss of pointer error from near end of link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.34 |
wanAtmStatsInLOSsA loss of signal error from far end of link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.35 |
wanAtmStatsOutLOSsA loss of signal error from near end of link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.36 |
wanAtmStatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.37 |
wanAtmStatsStatusThe status of this wanAtmStatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.38 |
wanProtocolStats OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2 |
wanX25StatsTableX.25 Packet layer statistics. SEQUENCE OF WanX25StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1 |
wanX25StatsEntryThe statistics for an X.25 interface across all LCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an X.25 network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanX25StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1 |
wanX25StatsIndexThe value of this object uniquely identifies this wanX25StatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.1 |
wanX25StatsDataSourceThis object identifies the source of the data that this wanX25StatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be rfc887-x25(5).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.2 |
wanX25StatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.3 |
wanX25StatsInFramesThe total number of frames seen coming from the far end of the link including error packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.4 |
wanX25StatsOutFramesThe total number of frames seen coming from the near end of the link including error packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.5 |
wanX25StatsInOctetsThe sum of octets from all frames seen originating from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.6 |
wanX25StatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.7 |
wanX25StatsInRejectsThe number of REJ or SREJ frames see coming from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.8 |
wanX25StatsOutRejectsThe number of REJ or SREJ frames see coming from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.9 |
wanX25StatsInAttemptsThe number of call setup attempts initiated from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.10 |
wanX25StatsOutAttemptsThe number of call setup attempts initiated from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.11 |
wanX25StatsInFailuresThe number call setup attempt failures seen coming from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.12 |
wanX25StatsOutFailuresThe number call setup attempt failures seen coming from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.13 |
wanX25StatsProviderClearsThe number of clear request seen with a cause code other than DTE initiated.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.14 |
wanX25StatsInResetsThe number of reset requests seen from the far end of the link with cause code DTE initiated.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.15 |
wanX25StatsOutResetsThe number of reset requests seen from the near end of the link with cause code DTE initiated.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.16 |
wanX25StatsProviderResetsThe number of reset requests seen with cause code other than DTE initiated.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.17 |
wanX25StatsInAccusedErrorsThe numbers of packets seen from the far end of the link containing a procedure error cause code. These include clear, reset, restart, or diagnostic packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.18 |
wanX25StatsOutAccusedErrorsThe numbers of packets seen from the near end of the link containing a procedure error cause code. These include clear, reset, restart, or diagnostic packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.19 |
wanX25StatsInInterruptsThe number of interrupts packets seen coming from the far end of the link over all VCs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.20 |
wanX25StatsOutInterruptsThe number of interrupts packets seen coming from the near end of the link over all VCs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.21 |
wanX25StatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.22 |
wanX25StatsStatusThe status of this wanX25StatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.23 |
wanFrStatsTableFrame Relay statistics. SEQUENCE OF WanFrStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2 |
wanFrStatsEntryThe statistics for a frame relay interface across all DLCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a frame relay network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanFrStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1 |
wanFrStatsIndexThe value of this object uniquely identifies this wanFrStatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.1 |
wanFrStatsDataSourceThis object identifies the source of the data that this wanFrStatsEntry analyzes. This source can be any frame relay interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be frameRelay(32).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.2 |
wanFrStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.3 |
wanFrStatsInFramesThe total number of frames seen coming from the far end of the link including error packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.4 |
wanFrStatsOutFramesThe total number of frames seen coming from the near end of the link including error packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.5 |
wanFrStatsInOctetsThe sum of octets from all frames seen originating from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.6 |
wanFrStatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.7 |
wanFrStatsInFECNsThe number of frames see coming form the far end of the link with the FECN bit set.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.8 |
wanFrStatsOutFECNsThe number of frames see coming form the near end of the link with the FECN bit set.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.9 |
wanFrStatsInBECNsThe number of frames seen coming from the far end of the link with the BECN bit set.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.10 |
wanFrStatsOutBECNsThe number of frames seen coming from the near end of the link with the BECN bit set.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.11 |
wanFrStatsInDEsThe number of frames seen coming from the far end of the link with the DE bit set.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.12 |
wanFrStatsOutDEsThe number of frames seen coming from the near end of the link with the DE bit set.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.13 |
wanFrStatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.14 |
wanFrStatsStatusThe status of this wanFrStatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.15 |
wanAal5StatsTableAAL/5 statistics. SEQUENCE OF WanAal5StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3 |
wanAal5StatsEntryThe statistics for a AAL/5 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanAal5StatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1 |
wanAal5StatsIndexThe value of this object uniquely identifies this wanAal5StatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.1 |
wanAal5StatsDataSourceThis object identifies the source of the data that this wanAal5StatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be aal5(49).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.2 |
wanAal5StatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.3 |
wanAal5StatsInCellsThe total number of cells for any AAL-5 connection seen coming from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.4 |
wanAal5StatsOutCellsThe total number of cells for any AAL-5 connection seen coming from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.5 |
wanAal5StatsInPDUsThe total number of AAL-5 PDUs seen coming from the far end of the link including error PDUs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.6 |
wanAal5StatsOutPDUsThe total number of AAL-5 PDUs seen coming from the near end of the link including error PDUs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.7 |
wanAal5StatsInOctetsThe sum of octets from all AAL-5 PDUs seen originating from the far end of the link including errored PDUs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.8 |
wanAal5StatsOutOctetsThe sum of octets from all AAL-5 PDUs seen originating from the near end of the link including errored PDUs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.9 |
wanAal5StatsInCLP1The total number of cells for any AAL-5 connection with the CLP bit set seen coming from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.10 |
wanAal5StatsOutCLP1The total number of cells for any AAL-5 connection with the CLP bit set seen coming from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.11 |
wanAal5StatsInCRCsThe total number of AAL-5 PDUs with CRC errors from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.12 |
wanAal5StatsOutCRCsThe total number of AAL-5 PDUs with CRC errors from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.13 |
wanAal5StatsInOversizedSDUsThe total number of AAL-5 SDUs from the far end of the link that were too large.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.14 |
wanAal5StatsOutOversizedSDUsThe total number of AAL-5 SDUs from the near end of the link that were too large.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.15 |
wanAal5StatsInSVCsThe total number of AAL/5 connections seen initiated from the far end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.16 |
wanAal5StatsOutSVCsThe total number of AAL-5 connections seen initiated from the near end of the link.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.17 |
wanAal5StatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.18 |
wanAal5StatsStatusThe status of this wanAal5StatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.19 |
wanPppStatsTablePPP in HDLC service statistics. SEQUENCE OF WanPppStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4 |
wanPppStatsEntryThe statistics for a PPP in HDLC service. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanPppStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1 |
wanPppStatsIndexThe value of this object uniquely identifies this wanPppStatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.1 |
wanPppStatsDataSourceThis object identifies the source of the data that this wanPppStatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be ppp(22).rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.2 |
wanPppStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.3 |
wanPppStatsInFramesThe total number of frames seen coming from the far end of the link including error frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.4 |
wanPppStatsOutFramesThe total number of frames seen coming from the near end of the link including error frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.5 |
wanPppStatsInOctetsThe sum of octets from all frames seen coming from the far end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.6 |
wanPppStatsOutOctetsThe sum of octets from all frames seen coming from the near end of the link including errored frames.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.7 |
wanPppStatsInBadAddressesThe number of frames seen from the far end of the link with an incorrect address field.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.8 |
wanPppStatsOutBadAddressesThe number of frames seen from the near end of the link with an incorrect address fieldro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.9 |
wanPppStatsInBadControlsThe number of frames seen from the far end of the link with an incorrect control field.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.10 |
wanPppStatsOutBadControlsThe number of frames seen from the near end of the link with an incorrect control field.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.11 |
wanPppStatsInLongFramesThe number of frames seen from the far end of the link that exceed the MRU.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.12 |
wanPppStatsOutLongFramesThe number of frames seen from the near end of the link that exceed the MRU.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.13 |
wanPppStatsInBadFCSsThe number of packets seen from the far end of the link with incorrect FCSs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.14 |
wanPppStatsOutBadFCSsThe number of packets seen from the near end of the link with incorrect FCSs.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.15 |
wanPppStatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.16 |
wanPppStatsStatusThe status of this wanPppStatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.17 |
wanPvcStats OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3 |
wanX25PvcStatsTableX.25 per-LCI statistics for a PVC. SEQUENCE OF WanX25PvcStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1 |
wanX25PvcStatsEntryThe statistics for a X.25 PVC. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the sides the probe is not on. WanX25PvcStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1 |
wanX25PvcStatsIndexThe value of this object uniquely identifies this wanX25PvcStatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.1 |
wanX25PvcStatsDataSourceThis object identifies the source of the data that this wanX25PvcStatsEntry analyzes. This source can be any pvcEntry associated with an X.25 interface. In order to identify a particular LCI to monitor, this object shall identify the instance of the pvcIndex object that corresponds to a X.25 PVC, defined above for the desired interface.rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.2 |
wanX25PvcStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.3 |
wanX25PvcStatsInFramesThe total number of frames seen coming from the far end of the link on this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.4 |
wanX25PvcStatsOutFramesThe total number of frames seen coming from the near end of the link on this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.5 |
wanX25PvcStatsInOctetsThe sum of octets from all frames seen originating from the far end of the link on this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.6 |
wanX25PvcStatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link on this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.7 |
wanX25PvcStatsInResetsThe number of reset requests seen from the far end of the link with cause code DTE initiated for this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.8 |
wanX25PvcStatsOutResetsThe number of reset requests seen from the far end of the link with cause code DTE initiated for this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.9 |
wanX25PvcStatsProviderResetsThe number of reset requests seen with cause code other than DTE initiated for this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.10 |
wanX25PvcStatsInAccusedErrorsThe numbers of frames seen from the far end of the link containing a procedure error cause code on this LCI. These include clear, reset, restart, or diagnostic packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.11 |
wanX25PvcStatsOutAccusedErrorsThe numbers of frames seen from the near end of the link containing a procedure error cause code on this LCI. These include clear, reset, restart, or diagnostic packets.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.12 |
wanX25PvcStatsInInterruptsThe number of interrupts frames seen coming from the far end of the link on this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.13 |
wanX25PvcStatsOutInterruptsThe number of interrupts frames seen coming from the far end of the link on this LCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.14 |
wanX25PvcStatsUpTimeThe total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanX25PvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this LCI was down. It only means the probe was not certain it was up. Note: the sum of wanX25PvcStatsUpTime and wanX25PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this LCI, i.e., the total time the value of wanX25PvcStatsState was unknown(3).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.15 |
wanX25PvcStatsDownTimeThe total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanX25PvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this LCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanX25PvcStatsUpTime and wanX25PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this LCI, i.e., the total time the value of wanX25PvcStatsState was unknown(3).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.16 |
wanX25PvcStatsStateThe current state of this LCI as inferred by the probe. A value of up(2) means the LCI is active. A value of down(2) means the LCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.ro Enumeration .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.17 |
wanX25PvcStatsStateChangesThe count of the number of times the wanX25PvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanX25PvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.18 |
wanX25PvcStatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.19 |
wanX25PvcStatsStatusThe status of this wanX25PvcStatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.20 |
wanFrPvcStatsTableFrame Relay per-DLCI statistics. SEQUENCE OF WanFrPvcStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2 |
wanFrPvcStatsEntryThe statistics for a frame relay DLCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanFrPvcStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1 |
wanFrPvcStatsIndexThe value of this object uniquely identifies this wanFrPvcStatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.1 |
wanFrPvcStatsDataSourceThis object identifies the source of the data that this wanFrPvcStatsEntry analyzes. This source can be any pvcEntry associated with a frame relay interface on this device. In order to identify a particular DLCI, this object shall identify the instance of the frame relay pvcIndex object, defined in the PVCCONFIG-MIB.rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.2 |
wanFrPvcStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.3 |
wanFrPvcStatsInFramesThe total number of frames seen coming from the far end of the link on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.4 |
wanFrPvcStatsOutFramesThe total number of frames seen coming from the near end of the link on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.5 |
wanFrPvcStatsInOctetsThe sum of octets from all frames seen originating from the far end of the link on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.6 |
wanFrPvcStatsOutOctetsThe sum of octets from all frames seen originating from the near end of the link on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.7 |
wanFrPvcStatsInFECNsThe number of frames see coming form the far end of the link with the FECN bit set on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.8 |
wanFrPvcStatsOutFECNsThe number of frames seen coming from the far end of the link with the BECN bit set on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.9 |
wanFrPvcStatsInBECNsThe number of frames see coming form the near end of the link with the FECN bit set.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.10 |
wanFrPvcStatsOutBECNsThe number of frames seen coming from the near end of the link with the BECN bit set on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.11 |
wanFrPvcStatsInDEsThe number of frames seen coming from the far end of the link with the DE bit set on this DCLI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.12 |
wanFrPvcStatsOutDEsThe number of frames seen coming from the near end of the link with the DE bit set on this DLCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.13 |
wanFrPvcStatsUpTimeThe total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanFrPvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this LCI was down. It only means the probe was not certain it was up. Note: the sum of wanFrPvcStatsUpTime and wanFrPvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this DLCI, i.e., the total time the value of wanFrPvcStatsState was unknown(3).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.14 |
wanFrPvcStatsDownTimeThe total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanFrPvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this LCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanX25PvcStatsUpTime and wanFrPvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this DLCI, i.e., the total time the value of wanFrPvcStatsState was unknown(3).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.15 |
wanFrPvcStatsStateThe current state of this DLCI as inferred by the probe. A value of up(2) means the DLCI is active. A value of down(2) means the DLCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.ro Enumeration .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.16 |
wanFrPvcStatsStateChangesThe count of the number of times the wanFrPvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanFrPvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.17 |
wanFrPvcStatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.18 |
wanFrPvcStatsStatusThe status of this wanFrPvcStatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.19 |
wanAal5PvcStatsTableAAL/5 per-VPI/VCI statistics. SEQUENCE OF WanAal5PvcStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3 |
wanAal5PvcStatsEntryThe statistics for a AAL-5 VCI/VPI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanAal5PvcStatsEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1 |
wanAal5PvcStatsIndexThe value of this object uniquely identifies this wanAal5PvcStatsTable entry. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.1 |
wanAal5PvcStatsDataSourceThis object identifies the source of the data that this wanAal5StatsEntry analyzes. This source can be any pvcEntry that is associated with an ATM interface on this device. In order to identify a particular VPI/VCI, this object shall identify the instance of the pvcIndex object, defined in the PVCCONFIG-MIB.rw OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.2 |
wanAal5PvcStatsDropEventsThe total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.3 |
wanAal5PvcStatsInCellsThe total number of cells for seen coming from the far end of the link on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.4 |
wanAal5PvcStatsOutCellsThe total number of cells seen coming from the near end of the link on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.5 |
wanAal5PvcStatsInPDUsThe total number of AAL-5 PDUs seen coming from the far end of the link on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.6 |
wanAal5PvcStatsOutPDUsThe total number of AAL-5 PDUs seen coming from the near end of the link on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.7 |
wanAal5PvcStatsInOctetsThe sum of octets from all AAL-5 PDUs seen originating from the far end of the link on this VCI/VPI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.8 |
wanAal5PvcStatsOutOctetsThe sum of octets from all AAL-5 PDUs seen originating from the near end of the link on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.9 |
wanAal5PvcStatsInCLP1The total number of cells with the CLP bit set seen coming from the far end of the link on this VCI/VPI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.10 |
wanAal5PvcStatsOutCLP1The total number of cells with the CLP bit set seen coming from the near end of the link on this VCI/VPI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.11 |
wanAal5PvcStatsInCRCsThe total number of AAL-5 PDUs with CRC errors seen coming from the far end of the link on this VCI/VPI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.12 |
wanAal5PvcStatsOutCRCsThe total number of AAL-5 PDUs with CRC errors seen coming from the near end of the link on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.13 |
wanAal5PvcStatsInOversizedSDUsThe number of AAL5 SDUs from the far end of the link that were too large on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.14 |
wanAal5PvcStatsOutOversizedSDUsThe number of AAL5 SDUs from the near end of the link that were too large on this VPI/VCI.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.15 |
wanAal5PvcStatsUpTimeThe total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanAal5PvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this VPI/VCI was down. It only means the probe was not certain it was up. Note: the sum of wanAal5PvcStatsUpTime and wanAal5PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this VPI/VCI, i.e., the total time the value of wanAal5PvcStatsState was unknown(3).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.16 |
wanAal5PvcStatsDownTimeThe total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanAal5PvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this VPI/VCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanAal5PvcStatsUpTime and wanAal5PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this VPI/VCI, i.e., the total time the value of wanAal5PvcStatsState was unknown(3).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.17 |
wanAal5PvcStatsStateThe current state of this VPI/VCI as inferred by the probe. A value of up(2) means the LCI is active. A value of down(2) means the VPI/VCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.ro Enumeration .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.18 |
wanAal5PvcStatsStateChangesThe count of the number of times the wanAal5PvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanAal5PvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.19 |
wanAal5PvcStatsOwnerThe entity that configured this entry.rw OwnerString (RMON-MIB) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.20 |
wanAal5PvcStatsStatusThe status of this wanAal5PvcStatsTable entry.rw RowStatus -- .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.21 |
wanHistoryMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2 |
wanSignalingHistory OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1 |
wanT1E1HistoryTableT1/E1 signaling statistics. SEQUENCE OF WanT1E1HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1 |
wanT1E1HistoryEntryStatistics for a particular T1/E1 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanT1E1HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1 |
wanT1E1HistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.1 |
wanT1E1HistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. OBJECT IDENTIFIER SYNTAX INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.2 |
wanT1E1HistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.3 |
wanT1E1HistoryDropEventsThe change in value of wanT1E1StatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.4 |
wanT1E1HistoryInFramesThe change in value of wanT1E1StatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.5 |
wanT1E1HistoryOutFramesThe change in value of wanT1E1StatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.6 |
wanT1E1HistoryInOctetsThe change in value of wanT1E1StatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.7 |
wanT1E1HistoryOutOctetsThe change in value of wanT1E1StatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.8 |
wanT1E1HistoryESsThe change in value of wanT1E1StatsESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.9 |
wanT1E1HistorySESsThe change in value of wanT1E1StatsSESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.10 |
wanT1E1HistorySEFSsThe change in value of wanT1E1StatsSEFSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.11 |
wanT1E1HistoryOOFsThe change in value of wanT1E1StatsOOFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.12 |
wanT1E1HistoryUASsThe change in value of wanT1E1StatsUASs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.13 |
wanT1E1HistoryCSSsThe change in value of wanT1E1StatsCSSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.14 |
wanT1E1HistoryPCVsThe change in value of wanT1E1StatsPCVs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.15 |
wanT1E1HistoryLESsThe change in value of wanT1E1StatsLESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.16 |
wanT1E1HistoryBESsThe change in value of wanT1E1StatsBESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.17 |
wanT1E1HistoryDMsThe change in value of wanT1E1StatsDMs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.18 |
wanT1E1HistoryLCVsThe change in value of wanT1E1StatsLCVs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.19 |
wanT1E1HistoryLOFsThe change in value of wanT1E1StatsLOFSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.20 |
wanT1E1HistoryLOSsThe change in value of wanT1E1StatsLOSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.21 |
wanT1E1HistoryRAIsThe change in value of wanT1E1StatsRAIs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.22 |
wanT1E1HistoryAISsThe change in value of wanT1E1StatsAISs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.23 |
wanT1E1HistoryTS16AISsThe change in value of wanT1E1StatsTS16AISs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.24 |
wanT1E1HistoryLOMFsThe change in value of wanT1E1StatsLOMFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.25 |
wanT1E1HistoryFarLOMFsThe change in value of wanT1E1StatsFarLOMFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.26 |
wanT1E1HistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.27 |
wanT1E1HistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.28 |
wanVSeriesHistoryTableThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. SEQUENCE OF WanVSeriesHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2 |
wanVSeriesHistoryEntryThe statistics for a V-series interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanVSeriesHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1 |
wanVSeriesHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.1 |
wanVSeriesHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.2 |
wanVSeriesHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.3 |
wanVSeriesHistoryDropEventsThe change in value of wanVSeriesStatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.4 |
wanVSeriesHistoryInFramesThe change in value of wanVSeriesStatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.5 |
wanVSeriesHistoryOutFramesThe change in value of wanVSeriesStatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.6 |
wanVSeriesHistoryInOctetsThe change in value of wanVSeriesStatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.7 |
wanVSeriesHistoryOutOctetsThe change in value of wanVSeriesStatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.8 |
wanVSeriesHistoryInFCSsThe change in value of wanVSeriesStatsInFCSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.9 |
wanVSeriesHistoryOutFCSsThe change in value of wanVSeriesStatsOutFCSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.10 |
wanVSeriesHistoryInOverrunsThe change in value of wanVSeriesStatsInOverruns during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.11 |
wanVSeriesHistoryOutOverrunsThe change in value of wanVSeriesStatsOutOverruns during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.12 |
wanVSeriesHistoryInterruptedFramesThe change in value of wanVSeriesStatsInterruptedFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.13 |
wanVSeriesHistoryInAbortedFramesThe change in value of wanVSeriesStatsInAbortedFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.14 |
wanVSeriesHistoryOutAbortedFramesThe change in value of wanVSeriesStatsOutAbortedFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.15 |
wanVSeriesHistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.16 |
wanVSeriesHistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.17 |
wanHssiHistoryTableHSSI interface statistics.deprecated SEQUENCE OF WanHssiHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3 |
wanHssiHistoryEntryThe statistics for a HSSI interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.deprecated WanHssiHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1 |
wanHssiHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.deprecated INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.1 |
wanHssiHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.deprecated INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.2 |
wanHssiHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.rodeprecated TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.3 |
wanHssiHistoryDropEventsThe change in value of wanHssiStatsDropEvents during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.4 |
wanHssiHistoryInFramesThe change in value of wanHssiStatsInFrames during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.5 |
wanHssiHistoryOutFramesThe change in value of wanHssiStatsOutFrames during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.6 |
wanHssiHistoryInOctetsThe change in value of wanHssiStatsInOctets during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.7 |
wanHssiHistoryOutOctetsThe change in value of wanHssiStatsOutOctets during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.8 |
wanHssiHistoryRxLongFramesThe change in value of wanHssiStatsRxLongFrames during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.9 |
wanHssiHistoryRxCrcErrorsThe change in value of wanHssiStatsRxCrcErrors during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.10 |
wanHssiHistoryRxOverrunsThe change in value of wanHssiStatsRxOverruns during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.11 |
wanHssiHistoryRxAbortsThe change in value of wanHssiStatsRxAborts during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.12 |
wanHssiHistoryTxAbortsThe change in value of wanHssiStatsTxAborts during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.13 |
wanHssiHistoryTxUnderrunsThe change in value of wanHssiStatsTxUnderruns during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.14 |
wanHssiHistoryRxRingErrorsThe change in value of wanHssiStatsTxRingErrors during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.15 |
wanHssiHistoryRxRingOverrunsThe change in value of wanHssiStatsRxRingOverruns during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.16 |
wanHssiHistoryTxRingErrorsThe change in value of wanHssiStatsTxRingErrors during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.17 |
wanHssiHistoryPortOpErrorsThe change in value of wanHssiStatsPortOpErrors during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.18 |
wanHssiHistoryTxCmplProcessingsThe change in value of wanHssiStatsTxCmplProcessings during the interval.rodeprecated Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.19 |
wanHssiHistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.rodeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.20 |
wanHssiHistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.rodeprecated INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.21 |
wanT3E3HistoryTableT3/E3 signaling statistics SEQUENCE OF WanT3E3HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4 |
wanT3E3HistoryEntryStatistics for a T3/E3 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanT3E3HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1 |
wanT3E3HistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.1 |
wanT3E3HistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.2 |
wanT3E3HistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.3 |
wanT3E3HistoryDropEventsThe change in value of wanT3E3StatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.4 |
wanT3E3HistoryInFramesThe change in value of wanT3E3StatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.5 |
wanT3E3HistoryOutFramesThe change in value of wanT3E3StatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.6 |
wanT3E3HistoryInOctetsThe change in value of wanT3E3StatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.7 |
wanT3E3HistoryOutOctetsThe change in value of wanT3E3StatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.8 |
wanT3E3HistoryPESsThe change in value of wanT3E3StatsPESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.9 |
wanT3E3HistoryPSESsThe change in value of wanT3E3StatsPSESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.10 |
wanT3E3HistoryOOFsThe change in value of wanT3E3StatsOOFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.11 |
wanT3E3HistorySEFSsThe change in value of wanT3E3StatsSEFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.12 |
wanT3E3HistoryUASsThe change in value of wanT3E3StatsUASs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.13 |
wanT3E3HistoryLCVsThe change in value of wanT3E3StatsLCVs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.14 |
wanT3E3HistoryPCVsThe change in value of wanT3E3StatsPCVs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.15 |
wanT3E3HistoryLESsThe change in value of wanT3E3StatsLESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.16 |
wanT3E3HistoryCCVsThe change in value of wanT3E3StatsCCVs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.17 |
wanT3E3HistoryCESsThe change in value of wanT3E3StatsCESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.18 |
wanT3E3HistoryCSESsThe change in value of wanT3E3StatsCSESs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.19 |
wanT3E3HistoryRAIsThe change in value of wanT3E3StatsRAIs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.20 |
wanT3E3HistoryAISsThe change in value of wanT3E3StatsAISs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.21 |
wanT3E3HistoryLOFsThe change in value of wanT3E3StatsLOFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.22 |
wanT3E3HistoryLOSsThe change in value of wanT3E3StatsLOSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.23 |
wanT3E3HistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.24 |
wanT3E3HistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.25 |
wanAtmHistoryTableATM signaling statistics. SEQUENCE OF WanAtmHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5 |
wanAtmHistoryEntryThe statistics for an ATM interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanAtmHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1 |
wanAtmHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.1 |
wanAtmHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.2 |
wanAtmHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.3 |
wanAtmHistoryDropEventsThe change in value of wanAtmStatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.4 |
wanAtmHistoryInCellsThe change in value of wanAtmStatsInCells during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.5 |
wanAtmHistoryOutCellsThe change in value of wanAtmStatsOutCells during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.6 |
wanAtmHistoryInCLP1The change in value of wanAtmStatsInCLP1 during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.7 |
wanAtmHistoryOutCLP1The change in value of wanAtmStatsOutCLP1 during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.8 |
wanAtmHistoryConnectionEventsThe change in value of wanAtmStatsConnectionEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.9 |
wanAtmHistoryErroredPDUsThe change in value of wanAtmStatsErroredPDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.10 |
wanAtmHistorySetupAttemptsThe change in value of wanAtmStatsSetupAttempts during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.11 |
wanAtmHistoryInRoutesUnavailableThe change in value of wanAtmStatsInRoutesUnavailable during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.12 |
wanAtmHistoryOutRoutesUnavailableThe change in value of wanAtmStatsOutRoutesUnavailable during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.13 |
wanAtmHistoryInResourcesUnavailableThe change in value of wanAtmStatsInResourcesUnavailable during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.14 |
wanAtmHistoryOutResourcesUnavailableThe change in value of wanAtmStatsOutResourcesUnavailable during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.15 |
wanAtmHistoryInUnsuccessfulCallsThe change in value of wanAtmStatsInUnsuccessfulCalls during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.16 |
wanAtmHistoryOutUnsuccessfulCallsThe change in value of wanAtmStatsOutUnsuccessfulCalls during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.17 |
wanAtmHistoryInIncorrectMsgsThe change in value of wanAtmStatsInIncorrectMsgs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.18 |
wanAtmHistoryOutIncorrectMsgsThe change in value of wanAtmStatsOutIncorrectMsgs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.19 |
wanAtmHistoryInPartyEventsThe change in value of wanAtmStatsInPartyEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.20 |
wanAtmHistoryOutPartyEventsThe change in value of wanAtmStatsOutPartyEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.21 |
wanAtmHistoryInExpiriesThe change in value of wanAtmStatsInExpiries during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.22 |
wanAtmHistoryOutExpiriesThe change in value of wanAtmStatsOutExpiries during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.23 |
wanAtmHistoryInRestartErrorsThe change in value of wanAtmStatsInRestartErrors during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.24 |
wanAtmHistoryOutRestartErrorsThe change in value of wanAtmStatsOutRestartErrors during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.25 |
wanAtmHistoryInSVCsThe change in value of wanAtmStatsInSVCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.26 |
wanAtmHistoryOutSVCsThe change in value of wanAtmStatsOutSVCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.27 |
wanAtmHistoryInOCDsThe change in value of wanAtmStatsInOCDs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.28 |
wanAtmHistoryOutOCDsThe change in value of wanAtmStatsOutOCDs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.29 |
wanAtmHistoryInLOCsThe change in value of wanAtmStatsInLOCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.30 |
wanAtmHistoryOutLOCsThe change in value of wanAtmStatsOutLOCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.31 |
wanAtmHistoryInLOFsThe change in value of wanAtmStatsInLOFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.32 |
wanAtmHistoryOutLOFsThe change in value of wanAtmStatsOutLOFs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.33 |
wanAtmHistoryInLOPsThe change in value of wanAtmStatsInLOPs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.34 |
wanAtmHistoryOutLOPsThe change in value of wanAtmStatsOutLOPs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.35 |
wanAtmHistoryInLOSsThe change in value of wanAtmStatsInLOSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.36 |
wanAtmHistoryOutLOSsThe change in value of wanAtmStatsOutLOSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.37 |
wanAtmHistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.38 |
wanAtmHistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.39 |
wanProtocolHistory OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2 |
wanX25HistoryTableX.25 Packet layer statistics. SEQUENCE OF WanX25HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1 |
wanX25HistoryEntryThe statistics for an X.25 interface across all LCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a X.25 network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanX25HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1 |
wanX25HistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.1 |
wanX25HistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.2 |
wanX25HistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.3 |
wanX25HistoryDropEventsThe change in value of wanX25StatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.4 |
wanX25HistoryInFramesThe change in value of wanX25StatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.5 |
wanX25HistoryOutFramesThe change in value of wanX25StatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.6 |
wanX25HistoryInOctetsThe change in value of wanX25StatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.7 |
wanX25HistoryOutOctetsThe change in value of wanX25StatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.8 |
wanX25HistoryInRejectsThe change in value of wanX25StatsInRejects during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.9 |
wanX25HistoryOutRejectsThe change in value of wanX25StatsOutRejects during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.10 |
wanX25HistoryInAttemptsThe change in value of wanX25StatsInAttempts during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.11 |
wanX25HistoryOutAttemptsThe change in value of wanX25StatsOutAttempts during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.12 |
wanX25HistoryInFailuresThe change in value of wanX25StatsInFailures during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.13 |
wanX25HistoryOutFailuresThe change in value of wanX25StatsOutFailures during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.14 |
wanX25HistoryProviderClearsThe change in value of wanX25StatsProviderClears during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.15 |
wanX25HistoryInResetsThe change in value of wanX25StatsInResets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.16 |
wanX25HistoryOutResetsThe change in value of wanX25StatsOutResets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.17 |
wanX25HistoryProviderResetsThe change in value of wanX25StatsProviderResets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.18 |
wanX25HistoryInAccusedErrorsThe change in value of wanX25StatsInAccusedErrors during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.19 |
wanX25HistoryOutAccusedErrorsThe change in value of wanX25StatsOutAccusedErrors during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.20 |
wanX25HistoryInInterruptsThe change in value of wanX25StatsInInterrupts during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.21 |
wanX25HistoryOutInterruptsThe change in value of wanX25StatsOutInterrupts during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.22 |
wanX25HistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.23 |
wanX25HistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.24 |
wanFrHistoryTableFrame Relay statistics. SEQUENCE OF WanFrHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2 |
wanFrHistoryEntryThe statistics for a frame relay interface across all DLCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a frame relay network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanFrHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1 |
wanFrHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.1 |
wanFrHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.2 |
wanFrHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.3 |
wanFrHistoryDropEventsThe change in value of wanFrStatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.4 |
wanFrHistoryInFramesThe change in value of wanFrStatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.5 |
wanFrHistoryOutFramesThe change in value of wanFrStatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.6 |
wanFrHistoryInOctetsThe change in value of wanFrStatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.7 |
wanFrHistoryOutOctetsThe change in value of wanFrStatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.8 |
wanFrHistoryInFECNsThe change in value of wanFrStatsInFECSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.9 |
wanFrHistoryOutFECNsThe change in value of wanFrStatsOutFECNs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.10 |
wanFrHistoryInBECNsThe change in value of wanFrStatsInBECNs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.11 |
wanFrHistoryOutBECNsThe change in value of wanFrStatsOutBECNs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.12 |
wanFrHistoryInDEsThe change in value of wanFrStatsInDEs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.13 |
wanFrHistoryOutDEsThe change in value of wanFrStatsDOutDEs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.14 |
wanFrHistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.15 |
wanFrHistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.16 |
wanAal5HistoryTableAAL/5 statistics. SEQUENCE OF WanAal5HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3 |
wanAal5HistoryEntryThe statistics for a AAL/5 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table. WanAal5HistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1 |
wanAal5HistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.1 |
wanAal5HistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.2 |
wanAal5HistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.3 |
wanAal5HistoryDropEventsThe change in value of wanAal5StatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.4 |
wanAal5HistoryInCellsThe change in value of wanAal5StatsInCells during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.5 |
wanAal5HistoryOutCellsThe change in value of wanAal5StatsOutCells during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.6 |
wanAal5HistoryInPDUsThe change in value of wanAal5StatsInPDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.7 |
wanAal5HistoryOutPDUsThe change in value of wanAal5StatsOutPDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.8 |
wanAal5HistoryInOctetsThe change in value of wanAal5StatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.9 |
wanAal5HistoryOutOctetsThe change in value of wanAal5StatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.10 |
wanAal5HistoryInCLP1The change in value of wanAal5StatsInCLP1 the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.11 |
wanAal5HistoryOutCLP1The change in value of wanAal5StatsOutCLP1 during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.12 |
wanAal5HistoryInCRCsThe change in value of wanAal5StatsInCRCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.13 |
wanAal5HistoryOutCRCsThe change in value of wanAal5StatsOutCRCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.14 |
wanAal5HistoryInOversizedSDUsThe change in value of wanAal5StatsInOversizedSDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.15 |
wanAal5HistoryOutOversizedSDUsThe change in value of wanAal5StatsOutOversizedSDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.16 |
wanAal5HistoryInSVCsThe change in value of wanAal5StatsInSVCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.17 |
wanAal5HistoryOutSVCsThe change in value of wanAal5StatsOutSVCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.18 |
wanAal5HistoryInUtilizationThe best estimated of the mean AAL-5 layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.19 |
wanAal5HistoryOutUtilizationThe best estimated of the mean AAL-5 layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.20 |
wanPppHistoryTablePPP in HDLC service statistics. SEQUENCE OF WanPppHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4 |
wanPppHistoryEntryThe statistics for a PPP in HDLC service. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanPppHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1 |
wanPppHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.1 |
wanPppHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.2 |
wanPppHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.3 |
wanPppHistoryDropEventsThe change in value of wanPppStatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.4 |
wanPppHistoryInFramesThe change in value of wanPppStatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.5 |
wanPppHistoryOutFramesThe change in value of wanPppStatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.6 |
wanPppHistoryInOctetsThe change in value of wanPppStatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.7 |
wanPppHistoryOutOctetsThe change in value of wanPppStatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.8 |
wanPppHistoryInBadAddressesThe change in value of wanPppStatsInBadAddresses during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.9 |
wanPppHistoryOutBadAddressesThe change in value of wanPppStatsOutBadAddresses during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.10 |
wanPppHistoryInBadControlsThe change in value of wanPppStatsInBadControls during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.11 |
wanPppHistoryOutBadControlsThe change in value of wanPppStatsOutBadControls during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.12 |
wanPppHistoryInLongFramesThe change in value of wanPppStatsInLongFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.13 |
wanPppHistoryOutLongFramesThe change in value of wanPppStatsOutLongFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.14 |
wanPppHistoryInBadFCSsThe change in value of wanPppStatsInBadFCSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.15 |
wanPppHistoryOutBadFCSsThe change in value of wanPppStatsOutBadFCSs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.16 |
wanPppHistoryInUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.17 |
wanPppHistoryOutUtilizationThe best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.18 |
wanPvcHistory OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3 |
wanX25PvcHistoryTableX.25 per LCI statistics. SEQUENCE OF WanX25PvcHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1 |
wanX25PvcHistoryEntryThe statistics for a X.25 LCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanX25PvcHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1 |
wanX25PvcHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.1 |
wanX25PvcHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.2 |
wanX25PvcHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.3 |
wanX25PvcHistoryDropEventsThe change in value of wanX25PvcStatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.4 |
wanX25PvcHistoryInFramesThe change in value of wanX25PvcStatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.5 |
wanX25PvcHistoryOutFramesThe change in value of wanX25PvcStatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.6 |
wanX25PvcHistoryInOctetsThe change in value of wanX25PvcStatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.7 |
wanX25PvcHistoryOutOctetsThe change in value of wanX25PvcStatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.8 |
wanX25PvcHistoryInResetsThe change in value of wanX25PvcStatsInResets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.9 |
wanX25PvcHistoryOutResetsThe change in value of wanX25PvcStatsOutResets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.10 |
wanX25PvcHistoryProviderResetsThe change in value of wanX25PvcStatsProviderResets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.11 |
wanX25PvcHistoryInAccusedErrorsThe change in value of wanX25PvcStatsInAccusedErrors during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.12 |
wanX25PvcHistoryOutAccusedErrorsThe change in value of wanX25PvcStatsOutAccusedErrors during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.13 |
wanX25PvcHistoryInInterruptsThe change in value of wanX25PvcStatsInInterrupts during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.14 |
wanX25PvcHistoryOutInterruptsThe change in value of wanX25PvcStatsOutInterrupts during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.15 |
wanX25PvcHistoryUpTimeThe change in value of wanX25PvcStatsUpTime during the interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.16 |
wanX25PvcHistoryDownTimeThe change in value of wanX25PvcStatsDownTime during the interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.17 |
wanX25PvcHistoryStateChangesThe change in value of wanX25PvcStatsStateChanges during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.18 |
wanX25PvcHistoryInUtilizationThe best estimated of the mean utilization of traffic on this LCI coming from the far end of the link in hundreds of percent of the CIR.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.19 |
wanX25PvcHistoryOutUtilizationThe best estimated of the mean utilization of traffic on this LCI coming from the near end of the link in hundreds of percent of CIR.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.20 |
wanFrPvcHistoryTableFrame Relay per-DCLI statistics. SEQUENCE OF WanFrPvcHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2 |
wanFrPvcHistoryEntryThe statistics for a frame relay DLCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanFrPvcHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1 |
wanFrPvcHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.1 |
wanFrPvcHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.2 |
wanFrPvcHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.3 |
wanFrPvcHistoryDropEventsThe change in value of wanFrPvcStatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.4 |
wanFrPvcHistoryInFramesThe change in value of wanFrPvcStatsInFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.5 |
wanFrPvcHistoryOutFramesThe change in value of wanFrPvcStatsOutFrames during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.6 |
wanFrPvcHistoryInOctetsThe change in value of wanFrPvcStatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.7 |
wanFrPvcHistoryOutOctetsThe change in value of wanFrPvcStatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.8 |
wanFrPvcHistoryInFECNsThe change in value of wanFrPvcStatsInFECNs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.9 |
wanFrPvcHistoryOutFECNsThe change in value of wanFrPvcStatsOutFECNs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.10 |
wanFrPvcHistoryInBECNsThe change in value of wanFrPvcStatsInBECNs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.11 |
wanFrPvcHistoryOutBECNsThe change in value of wanFrPvcStatsOutBECNs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.12 |
wanFrPvcHistoryInDEsThe change in value of wanFrPvcStatsInDEs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.13 |
wanFrPvcHistoryOutDEsThe change in value of wanFrPvcStatsOutDEs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.14 |
wanFrPvcHistoryUpTimeThe change in value of wanFrPvcStatsUpTime during the interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.15 |
wanFrPvcHistoryDownTimeThe change in value of wanFrPvcStatsDownTime during the interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.16 |
wanFrPvcHistoryStateChangesThe change in value of wanFrPvcStatsStateChanges during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.17 |
wanFrPvcHistoryInUtilizationThe best estimated of the mean utilization of traffic on this DLCI coming from the far end of the link in hundreds of percent of the CIR.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.18 |
wanFrPvcHistoryOutUtilizationThe best estimated of the mean utilization of traffic on this DLCI coming from the near end of the link in hundreds of percent of CIR.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.19 |
wanAal5PvcHistoryTableAAL-5 per-VPI/VCI statistics. SEQUENCE OF WanAal5PvcHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3 |
wanAal5PvcHistoryEntryThe statistics for a AAL-5 VCI/VPI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. WanAal5PvcHistoryEntry .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1 |
wanAal5PvcHistoryIndexThe history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.1 |
wanAal5PvcHistorySampleIndexAn index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken. INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.2 |
wanAal5PvcHistoryIntervalStartThe value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.3 |
wanAal5PvcHistoryDropEventsThe change in value of wanAal5PvcStatsDropEvents during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.4 |
wanAal5PvcHistoryInCellsThe change in value of wanAal5PvcStatsInCells during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.5 |
wanAal5PvcHistoryOutCellsThe change in value of wanAal5PvcStatsOutCells during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.6 |
wanAal5PvcHistoryInPDUsThe change in value of wanAal5PvcStatsInPDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.7 |
wanAal5PvcHistoryOutPDUsThe change in value of wanAal5PvcStatsOutPDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.8 |
wanAal5PvcHistoryInOctetsThe change in value of wanAal5PvcStatsInOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.9 |
wanAal5PvcHistoryOutOctetsThe change in value of wanAal5PvcStatsOutOctets during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.10 |
wanAal5PvcHistoryInCLP1The change in value of wanAal5PvcStatsInCLP1 during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.11 |
wanAal5PvcHistoryOutCLP1The change in value of wanAal5PvcStatsOutCLP1 during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.12 |
wanAal5PvcHistoryInCRCsThe change in value of wanAal5PvcStatsInCRCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.13 |
wanAal5PvcHistoryOutCRCsThe change in value of wanAal5PvcStatsOutCRCs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.14 |
wanAal5PvcHistoryInOversizedSDUsThe change in value of wanAal5PvcStatsInOversizedSDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.15 |
wanAal5PvcHistoryOutOversizedSDUsThe change in value of wanAal5PvcStatsOutOversizedSDUs during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.16 |
wanAal5PvcHistoryUpTimeThe change in value of wanAal5PvcStatsUpTime during the interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.17 |
wanAal5PvcHistoryDownTimeThe change in value of wanAal5PvcStatsDownTime during the interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.18 |
wanAal5PvcHistoryStateChangesThe change in value of wanAal5PvcStatsStateChanges during the interval.ro Counter64 .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.19 |
wanAal5PvcHistoryInUtilizationThe best estimated of the mean utilization of traffic on this VPI/VCI coming from the far end of the link in hundreds of percent of the CIR.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.20 |
wanAal5PvcHistoryOutUtilizationThe best estimated of the mean utilization of traffic on this VPI/VCI coming from the near end of the link in hundreds of percent of CIR.ro INTEGER .1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.21 |