VOICE-OPT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
238
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
238 total| Object Name |
|---|
codex OBJECT IDENTIFIER .1.3.6.1.4.1.449 |
RFC1155-SMI Unknown .1.3.6.1.4.1.449 |
cdxProductSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.449.2 |
cdx6500 OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1 |
cdx6500Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2 |
cdx6500CfgProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1 |
cdx6500PCTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.1 |
cdx6500PCTVoicePortTable OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.1.25 |
cdx6500PPCTVoicePortTableThis table contains the port configuration parameters to
configure the DSPM/E&M, DSPM/FXS, DSPM/HC, and DSPM/SM. SEQUENCE OF Cdx6500PPCTVoicePortEntry .1.3.6.1.4.1.449.2.1.2.1.1.25.1 |
cdx6500PPCTVoicePortEntryA Voice Port Configuration Table Entry. Each entry contains
the configuration parameters for a single Voice Port. Cdx6500PPCTVoicePortEntry .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1 |
cdx6500VoiceCfgPortNumberPort number of the Voice port.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.1 |
cdx6500VoiceCfgPortTypeThis parameter represents the port type of the port.
voice :This is a voice port.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.2 |
cdx6500VoiceCfgInterfaceTypeSelect one of the following physical interfaces being used
for this port. The entry must match the hardware.
eAndM2 :2 wire E&M (Ear and Mouth) Interface.
eAndM4 :4 wire E&M (Ear and Mouth) Interface.
fxo :FXO (Foreign Exchange Office ) Interface.
fxs :FXS (Foreign Exchange Station) Interface.
nc :Skipped during configuration.
eAndM2 is only displayed for port numbers 1..54.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.3 |
cdx6500VoiceCfgSignalingTypeSelect the E&M signalling type.
i : EandMTypeI.
ii : EandMTypeII.
v : EandMTypeV.
iii : EandMTypeIII.
nc : Skipped during configuration.
This parameter is displayed for DSPM/E&M and skipped for
FXS, FXO, and all virtual port types.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.4 |
cdx6500VoiceCfgELeadFilterSelection for E lead filter enable or disable option.
disabled : Disables E-lead filter.
enabled : Enables E-lead filter.
nc : Skipped during configuration.
This parameter is displayed for DSPM/E&M and skipped for
FXS, FXO, and all virtual port types.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.5 |
cdx6500VoiceCfgHybridFXSHybrid balance filters and termination type based on country.
sixHundred : 600 ohm interface for USA, Japan and Ireland.
canada : 600 ohms with 2.16 uF
germany : 220 ohms in series with (820 ohms in parallel
with 115nF).
uk : 300 ohms in series with (1K ohms in parallel
with 220nF).
belgium : 150 ohms in series with (830 ohms in parallel
with 72nF).
france : 215 ohms in series with (1K ohms in parallel
with 137nF).
nc : Skipped during configuration.
This parameter is displayed for DSPM/FXS
and skipped for DSPM/E&M, DSPM/HC(FXO) and all virtual
port types.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.6 |
cdx6500VoiceCfgHybridEAndM2Hybrid balance filters and termination type based on country.
(Only for E&M-2wire interfaces.)
sixHundred : 600 ohm interface for USA, Japan and Ireland.
germany : 220 ohms in series with (820 ohms in parallel
with 115nF).
uk : 370 ohms in series with (620 ohms in parallel
with 310nF).
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.7 |
cdx6500VoiceCfgSignalingModeSelect the voice signalling mode.
normal : Allows signalling to pass end to end and
signalling will be used to control
circuit state and packet flow.
none : A permanent voice path is established and
packet flow is always enabled, but no
signalling will be passed through.
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.8 |
cdx6500VoiceCfgSignalingControlSelect signaling control transmission mode in E&M
interface type.
immediate : Digits are transmitted immediately.
wink : Digits are transmitted after the
WINK pulse.
transparent : The voice signalling states are
transmitted end to end without
interpreting the signalling state.
delay : Digits are transmitted after the end
of the Delay Dial signal.
masterColisee : 65xx is simulating Colisee master mode.
slaveColisee : 65xx is simulating Colisee slave mode.
seizureAcknowledge : Transmit Seizure acknowledge immediately
after receiving a Seizure signal from
the PBX.
nc : Skipped during configuration.
The parameter will be skipped for FXO & FXS type interface.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.9 |
cdx6500VoiceCfgNoOfDigitsToCollectSelect number of digits to collect before making a call.
The parameter will not be supported.rodeprecated INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.10 |
cdx6500VoiceCfgNoOfRingsNumber of rings to be received before a call can be
accepted. This parameter is displayed for FXO and skipped
for E&M and FXS interface types. A value of 0 implies that
this parameter was skipped during configuration.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.11 |
cdx6500VoiceCfgPCMModeSelect the PCM encoder/decoder mode.
aLaw :PCM encoder/decoder mode = A Law.
muLaw :PCM encoder/decoder mode = Mu Law.
nc :Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.12 |
cdx6500VoiceCfgCompressionRateSelect the voice compression rate to be used by the DSP.
cD8K : 8k CVSELP
c16k : 16k CVSELP
cBD8K : Bundled 8k CVSELP
cB16k : Bundled 16k CVSELP.
cE8Kb : Enhanced Bundled 8k CVSELP
cE16Kb : Enhanced Bundled 16k CVSELP
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.13 |
cdx6500VoiceCfgDSIControlSelect if the Digital Speech Interpolation (Silence Detector)
will be used with this channel.
enabled : DSI is activated.
disabled : DSI is not used.
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.14 |
cdx6500VoiceCfgSmoothingDelaySelect maximum inter packet arrival jitter due to network in
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.15 |
cdx6500VoiceCfgEchoControlSelect echo control.
disabled : Echo pass through.
enabled : This enables echo control logic.
nc : Skipped during configuration.
Echo not detected and not cancelled.
This parameter will be skipped in normal mode and
only displayed when DEBUG is turned on.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.16 |
cdx6500VoiceCfgEchoReturnLossSelect echo return loss in dBm.
minus3 : -3 dBm.
minus6 : -6 dBm.
minus9 : -9 dBm.
minus12 : -12dBm.
nc :Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.17 |
cdx6500VoiceCfgTxInputSignalLevelEnter the input signal level. To be specified in steps
of 0.5 dBm
FXO Interface Type : 600 Ohms +6.0 to -2.5dbm
600 Ohms Adaptive +6.0 to -2.5dbm
FXS Interface Type : 600 Ohms +6.0 to -6.0dbm
Canada +6.0 to -5.5dbm
UK +4.5 to -7.5dbm
Germany +4.0 to -8.0dbm
France -2.0 to -9.0dbm
Belgium +4.0 to -8.0dbm
E&M Interface Type : 4-Wire/600 +7.0 to -16.0dbm
2-Wire/600 +7.0 to -16.0dbm
2-Wire/UK +5.0 to -16.0dbm
2-Wire/Germany +5.0 to -16.0dbm
Virtual Ports(100 and above): +8.0 to -6.0dbm
Entering a negative number for the 'Input Signal Level'
will result in the DSPM card amplifying the signal by that
many dB. Entering a positive number for the 'Input Signal
Level' will result in the DSPM card attenuating the signal
by that many dB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.18 |
cdx6500VoiceCfgRxOutputSignalLevelEnter the output signal level. To be selected in steps of
0.5 dBm.
FXO Interface Type : 600 Ohms +0.0 to -8.0dbm
600 Ohms Adaptive +0.0 to -8.0dbm
FXS Interface Type : 600 Ohms +0.0 to -9.0dbm
Canada +0.0 to -9.0dbm
UK -1.5 to -9.0dbm
Germany -2.0 to -9.0dbm
France -1.5 to -9.0dbm
Belgium -1.5 to -9.0dbm
E&M Interface Type : 4-Wire/600 +7.0 to -16.0dbm
2-Wire/600 +3.0 to -16.0dbm
2-Wire/UK +1.0 to -16.0dbm
2-Wire/Germany +0.0 to -16.0dbm
Virtual Ports(100 and above): +6.0 to -8.0dbm
Entering a negative number for the 'Output Signal Level'
will result in the DSPM card attenuating the signal by that
many dB. Entering a positive number for the 'Output Signal
Level' will result in the DSPM card amplifying the signal
by that many dB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.19 |
cdx6500VoiceCfgFaxSupportThis parameter selects whether the FAX data is to be
supported.
disabled : FAX data will not be detected.
enabled : Detects presence of FAX data.
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.20 |
cdx6500VoiceCfgFaxRatesSpecify the speed to switch to, when FAX data is detected.
This parameter is ignored if Fax support was disabled.
fr9600 : FAX to be transmitted across the network at 9600
bits per second.
fr4800 : FAX to be transmitted across the network at 4800
bits per second.
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.21 |
cdx6500VoiceCfgVoiceBandDetectionModem data detection.
yes : Detection of modem data enabled.
no : Detection of modem data disabled.
nc : Skipped during configuration.
This parameter will be skipped in normal mode.Displayed only
when DEBUG is turned on.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.22 |
cdx6500VoiceCfgAutoCallMnemonicThis mnemonic name is used to originate the call. It consists
of 0 - 8 alphanumeric characters.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.23 |
cdx6500VoiceCfgCallControlSelect calling method.
offhook : Call only when Offhook.Disconnect on Onhook.
auto : SVC does not depend on On/Offhook condition.It
remains established permanently after the power-up.
switched : Call only when interface goes offhook and
disconnect call when interface goes onhook.
Destination is determined by the DTMF
digits received.
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.24 |
cdx6500VoiceCfgAutoCallTimeoutTime interval between two successive calls in case of failure
of previous call.Used only in `Auto' call control mode.This
parameter will be skipped if Call Control is Offhook
and Switched.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.25 |
cdx6500VoiceCfgCallRetriesEnter maximum number of call retries when previous call
failed.Used only in Auto Call Control mode.'0' means try
forever. This parameter will be skipped if Call Control is
Offhook and Switched.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.26 |
cdx6500VoiceCfgGroupSubaddressSpecifies a port subaddress that is shared by several Voice
ports. Incoming calls with this subaddress are routed to one
of several ports sharing this subaddress. Another name for
the group of ports with the same Group Subaddress is Hunt
Group.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.27 |
cdx6500VoiceCfgBillingThis controls whether billing (accounting) records will be
created for calls on this port.
enabled : Billing is enabled.
disabled : Billing is disabled.
nc : Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.28 |
cdx6500VoiceCfgRxSignalingStateChangeFilterThe amount of time to declare a valid supervisory signaling
state change. The granularity is 10 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.29 |
cdx6500VoiceCfgT1E1RxIdleOnhookStateThe signalling state that represents the idle state.
For E1 ports and T1 ESF ports, these bits represent
the ABCD signalling bits on the interface. For T1 SF ports
these bits represent ABAB signalling bits. `x' means don't
care.The range is from 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.30 |
cdx6500VoiceCfgT1E1TxIdleOnhookStateThe signalling state that represents the idle state.
For E1 ports and T1 ESF ports, these bits represent
the ABCD signalling bits on the interface. For T1 SF ports
these bits represent ABAB signalling bits.
The range is from 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.31 |
cdx6500VoiceCfgT1E1RxActiveOffhookStateThe signalling state that represents the active state.
For E1 ports and T1 ESF ports, these bits represent
the ABCD signalling bits on the interface. For T1 SF ports
these bits represent ABAB signalling bits. ` x' means don't
care. The range is from 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.32 |
cdx6500VoiceCfgT1E1TxActiveOffhookStateThe signalling state that represents the active state.
For E1 ports and T1 ESF ports, these bits represent
the ABCD signalling bits on the interface.
The range is from 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.33 |
cdx6500VoiceCfgT1E1RingingStateThe signalling state that represents the ringing state. For
E1 ports and T1 ESF ports, these bits represent the ABCD
signalling bits on the interface. For T1 SF ports
these bits represent ABAB signalling bits. `x' means
don't care.
The range is from 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.34 |
cdx6500VoiceCfgT1E1NoRingingStateThe signalling state that represents the no ringing
state. For E1 ports and T1 ESF ports, these bits represent
the ABCD signalling bits on the interface. For T1 SF ports
these bits represent ABAB signalling bits. `x' means don't
care. The range is from 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.35 |
cdx6500VoiceCfgRxWinkStartTimerThis is the maximum time to wait for the beginning of the
wink signal from the PBX before declaring a wink start
malfunction. Granularity is 50 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.36 |
cdx6500VoiceCfgRxMinimumReceiveWinkThe amount of time required to declare a valid wink.
Granularity is 10 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.37 |
cdx6500VoiceCfgRxCalledEndGlareDetectThe length of time when a wink pulse will be detected as a
glare condition. Granularity is 50 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.38 |
cdx6500VoiceCfgRxFirstDigitTimerThe maximum time (in seconds) to wait for the first DTMF
digit before declaring a `busyout' state. Granularity is
1 second.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.39 |
cdx6500VoiceCfgRxInterdigitTimerThis is the maximum time (in seconds) to wait for a
subsequent receive digit before declaring a misdial.
Granularity is 1 second.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.40 |
cdx6500VoiceCfgTxWinkDelayThe time delay from receiving a valid Offhook state to start
transmitting a wink. Granularity is 10 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.41 |
cdx6500VoiceCfgTxWinkWidthThe width of the transmitted wink pulse. Granularity is 10
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.42 |
cdx6500VoiceCfgTxDigitDelayThe time delay before transmitting the first DTMF digit
after a wink is received.Granularity is 10 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.43 |
cdx6500VoiceCfgTxDigitOnThe time DTMF digits are transmitted. Granularity is 10
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.44 |
cdx6500VoiceCfgTxInterdigitTimeThe time between transmitting DTMF digits. Granularity is 10
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.45 |
cdx6500VoiceCfgRxInterringWaitThis is the maximum time to wait for subsequent receive
rings before declaring a call abandoned condition.
Granularity is 1 second.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.46 |
cdx6500VoiceCfgRxRingStateChangeFilterThe amount of time to declare the change in the ring state.
Granularity is 50 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.47 |
cdx6500VoiceCfgTxRingerOffLongThis timer is the long off period for ringer cadences that
have a short and long off period.For the cases where the
ring cadence defines one off period, the Tx Ringer Off Long
must be equal to Tx Ringer Off Short. Granularity is 50
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.48 |
cdx6500VoiceCfgTxRingerOffShortThis timer is the short off period for ringer cadences that
have a short and long off period.For the cases where the
ring cadence defines one off period, the Tx Ringer Off Long
must be equal to Tx Ringer Off Short. Granularity is 50
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.49 |
cdx6500VoiceCfgTxRingerOnThe time of the ringer on pulse. Granularity is 50
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.50 |
cdx6500VoiceCfgRxDisconnectTimerThe amount of time required to receive idle signaling to
disconnect a call.
For an analog FXO port, RX idle signaling is the loss of
loop current.
For a FXS port, RX idle signaling is when the interface
goes onhook.
For an analog E&M port, RX idle signaling is when the 'M'
lead goes idle.
For digital interfaces, the RX idle state is defined by the
'T1/E1 Rx Idle (on-hook) State' parameter.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.51 |
cdx6500VoiceCfgRxCalledEndDisconnectDelayTimerThe additional amount of time beyond the Rx Disconnect filter
the calling end must be Onhook to disconnect a call.
Granularity is 1 second.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.52 |
cdx6500VoiceCfgLineErrorRecoveryThe length of time voice will be suppressed after LOS or OF
condition clears.Granularity is 10 milliseconds. This parameter
will be displayed for virtual ports only.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.53 |
cdx6500VoiceCfgSignalingSampleRateThe time between sampling received signalling states and line
states.Granularity is 1 millisecond. This parameter will be
displayed only when the DEBUG flag is set.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.54 |
cdx6500VoiceCfgWaitForParamsThe amount of time to wait for a message to set the parameters
after receiving a disconnect message (messages occur in the
form of an event) before busying out the port.
Granularity is 1 second.
This parameter will be displayed only when the DEBUG flag
is set.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.55 |
cdx6500VoiceCfgSpareTimer1Spare timer number 1.Granularity is 1 millisecond.This
parameter will be displayed only when the DEBUG flag is set.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.56 |
cdx6500VoiceCfgSpareTimer2Spare timer number 2.Granularity is 1 millisecond. This
parameter will be displayed only when the DEBUG flag is set.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.57 |
cdx6500VoiceCfgTxInterdigitPauseTimeThe time between transmitting DTMF digits.
Enter in steps of 10 msec.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.58 |
cdx6500VoiceCfgRxMinimumFlashHookTimeThe shortest length of time required to be onhook to be
recognized as a flash-hook. This value must be less than
Rx Maximum Flash-Hook Time for flash-hook to be recognized.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.59 |
cdx6500VoiceCfgRxMaximumFlashHookTimeThe longest length of time to be onhook to be recognized as
a flash-hook. This value must be less than Rx Disconnect Timer
for flash-hook to be recognized. Note: the average of the
minimum and maximum flash-hook values will be the pulse width
for a transmitted flash-hook.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.60 |
cdx6500VoiceCfgTransparentSignalingIdleStateThe received signalling state that represents the idle
state. For E1 ports and T1 ESF ports, these bits represent
the ABCD signalling bits on the interface.`x' means don't care.
For E&M analog ports, Onhook is assumed for the idle state.
The range is 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.61 |
cdx6500VoiceCfgTransparentRxDisconnectFilterThe time the received signaling state must be equal to
the idle state to disconnect the voice call. Zero value
disables idle state disconnect and maintains the voice
call in the answered state.Time is entered in minutes.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.62 |
cdx6500VoiceCfgTransparentSignalingBusyoutStateThe received signalling state that represents the Busyout
state. For E1 ports and T1 ESF ports, these bits represent
the ABCD signalling bits on the interface.For E&M analog
ports, Offhook is assumed for the busyout/alarm state. The
range is 0000 to 1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.63 |
cdx6500VoiceCfgXlateSigInfo0000FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.64 |
cdx6500VoiceCfgXlateSigInfo1000FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.65 |
cdx6500VoiceCfgXlateSigInfo0100FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.66 |
cdx6500VoiceCfgXlateSigInfo1100FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.67 |
cdx6500VoiceCfgXlateSigInfo0010FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.68 |
cdx6500VoiceCfgXlateSigInfo1010FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.69 |
cdx6500VoiceCfgXlateSigInfo0110FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.70 |
cdx6500VoiceCfgXlateSigInfo1110FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.71 |
cdx6500VoiceCfgXlateSigInfo0001FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.72 |
cdx6500VoiceCfgXlateSigInfo1001FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.73 |
cdx6500VoiceCfgXlateSigInfo0101FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.74 |
cdx6500VoiceCfgXlateSigInfo1101FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.75 |
cdx6500VoiceCfgXlateSigInfo0011FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.76 |
cdx6500VoiceCfgXlateSigInfo1011FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.77 |
cdx6500VoiceCfgXlateSigInfo0111FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.78 |
cdx6500VoiceCfgXlateSigInfo1111FromRemoteToLocalPortTranslate the signalling information received from the remote
end to a value to be transmitted out the local port.If the
local port is a T1/ESF or E1 port enter the ABCD values, for
a T1/SF port, enter the AB(AB) value.
If the local port is an analog E&M port, enter 0000 for idle
(Onhook) and 1111 for active (Offhook). The range is 0000 to
1111.ro DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.79 |
cdx6500VoiceCfgDialToneLowerFrequencyThe lower of the two frequencies needed to generate the dial
tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.80 |
cdx6500VoiceCfgDialToneLowerFrequencyAmplitudeThe amplitude of the lower frequency to generate the dial tone.
To be specified in steps of 0.5dB, -30dB turn off output.
The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.81 |
cdx6500VoiceCfgDialToneUpperFrequencyThe higher of the two frequencies needed to generate the dial
tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.82 |
cdx6500VoiceCfgDialToneUpperFrequencyAmplitudeThe amplitude of the upper frequency to generate the dial tone.
To be specified in steps of 0.5dB, -30dB turn off output.
The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.83 |
cdx6500VoiceCfgRingBackToneLowerFrequencyThe lower of the two frequencies needed to generate the
Ringback tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.84 |
cdx6500VoiceCfgRingBackToneLowerFrequencyAmplitudeThe amplitude of the lower frequency to generate the
Ringback tone. To be specified in steps of 0.5dB, -30dB
turn off output.The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.85 |
cdx6500VoiceCfgRingBackToneUpperFrequencyThe higher of the two frequencies needed to generate the
Ring-back tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.86 |
cdx6500VoiceCfgRingBackToneUpperFrequencyAmplitudeThe amplitude of the upper frequency to generate the
Ringback tone. To be specified in steps of 0.5dB, -30dB
turn off output. The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.87 |
cdx6500VoiceCfgBusyToneLowerFrequencyThe lower of the two frequencies needed to generate the Busy
tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.88 |
cdx6500VoiceCfgBusyToneLowerFrequencyAmplitudeThe amplitude of the lower frequency to generate the Busy
tone. To be specified in steps of 0.5dB, -30dB turn off
output. The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.89 |
cdx6500VoiceCfgBusyToneUpperFrequencyThe higher of the two frequencies needed to generate the Busy
tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.90 |
cdx6500VoiceCfgBusyToneUpperFrequencyAmplitudeThe amplitude of the upper frequency to generate the Busy
tone. To be specified in steps of 0.5dB, -30dB turn off
output. The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.91 |
cdx6500VoiceCfgTxBusyToneOffTimeTimer for the Busy tone off state. Granularity is 50
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.92 |
cdx6500VoiceCfgTxBusyToneOnTimeTimer for the busy tone on state. Granularity is 50
milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.93 |
cdx6500VoiceCfgFastBusyToneLowerFrequencyThe lower of the two frequencies needed to generate the Fast
Busy tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.94 |
cdx6500VoiceCfgFastBusyToneLowerFrequencyAmplitudeThe amplitude of the lower frequency to generate the Fast Busy
tone. To be specified in steps of 0.5dB, -30dB turn off
output. The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.95 |
cdx6500VoiceCfgFastBusyToneUpperFrequencyThe higher of the two frequencies needed to generate the Fast
Busy tone.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.96 |
cdx6500VoiceCfgFastBusyToneUpperFrequencyAmplitudeThe amplitude of the upper frequency to generate the Fast Busy
tone. To be specified in steps of 0.5dB, -30dB turn off output.
The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.97 |
cdx6500VoiceCfgTxFastBusyToneOffTimeTimer for the Fast Busy tone off state.
Granularity is 50 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.98 |
cdx6500VoiceCfgTxFastBusyToneOnTimeTimer for the Fast Busy tone on state.
Granularity is 50 milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.99 |
cdx6500VoiceCfgHybridFXOHybrid balance filters.
sixHundred : 600 ohm interface.
adaptive : 600 ohm with adaptive filter.
nc : Skipped during configuration.
This parameter is displayed for DSPM/HC (FXO) and
skipped for DSPM/E&M, DSPM/FXS and all virtual port types.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.100 |
cdx6500VoiceCfgTxPulseThe width of the transmitted Seizure, PTS, or Answer
pulse in msec.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.101 |
cdx6500VoiceCfgRxMinPulseThe minimum pulse width to declare a valid received
Seizure, PTS, or Answer pulse.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.102 |
cdx6500VoiceCfgRxMaxPulseThe maximum pulse width to declare a valid received
Seizure, PTS, or Answer.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.103 |
cdx6500VoiceCfgTxMasterClearThe width of the transmitted Master Clear-Forward,
Clear-Back, or Release Guard pulse in msec.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.104 |
cdx6500VoiceCfgRxMinMasterClearThe minimum pulse width to declare a valid received Master
Clear-Forward, Clear-Back, or Release Guard.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.105 |
cdx6500VoiceCfgRxMaxMasterClearThe maximum pulse width to declare a valid received Master
Clear-Forward, Clear-Back, or Release Guard.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.106 |
cdx6500VoiceCfgTxSlaveClearThe width of the transmitted Slave Clear-Forward or
Clear-Back pulse in msec.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.107 |
cdx6500VoiceCfgRxMinSlaveClearThe minimum pulse width to declare a valid received
Slave Clear-Forward or Clear-Back.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.108 |
cdx6500VoiceCfgRxMaxSlaveClearThe maximum pulse width to declare a valid received
Slave Clear-Forward or Clear-Back.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.109 |
cdx6500VoiceCfgTxSlaveReleaseThe width of the transmitted Slave Release Guard pulse
in msec.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.110 |
cdx6500VoiceCfgRxMinSlaveReleaseThe minimum pulse width to declare a valid received Slave
Release Guard.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.111 |
cdx6500VoiceCfgRxMaxSlaveReleaseThe maximum pulse width to declare a valid received Slave
Release Guard.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.112 |
cdx6500VoiceCfgTxPTSTimeThe time delay from receiving a valid Seizure from the
PBX to start transmitting a PTS pulse.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.113 |
cdx6500VoiceCfgRxPTSTimeThe maximum time to wait for a PTS pulse from the PBX
after sending a Seizure before giving up and clearing
the trunk.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.114 |
cdx6500VoiceCfgMasterGuardThe time the master side waits in the guard state after
transmitting a clear pulse.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.115 |
cdx6500VoiceCfgSlaveGuardThe time the slave side waits in the guard state after
transmitting a clear pulse.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.116 |
cdx6500VoiceCfgTxFlashHookTimeThe lenght of time a flash signal will be transmitted
as a result of a flash-hook from the remote interface.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.117 |
cdx6500VoiceCfgDtmfAmplitudeThe amplitude of the DTMF digits.
To be specified in steps of 0.5dB, -30.0 turn off output.
The range is from -30dBm to -3dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.118 |
cdx6500VoiceCfgFXSOffhookFilterThis is the amoung of time a valid OFFHOOK conidtion must be
present before an analog FXS will declare OFFHOOK.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.25.1.1.119 |
cdx6500CfgGeneralGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.2 |
cdx6500GCTVoiceSwitchTable OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.2.21 |
cdx6500GGCTVoiceSwitchTableThis table contains the Voice Switch Table configuration. SEQUENCE OF Cdx6500VoiceSwitchEntry .1.3.6.1.4.1.449.2.1.2.2.21.1 |
cdx6500VoiceSwitchEntryEach entry contains a list of parameters that
makeup the Voice Switch Table. Cdx6500VoiceSwitchEntry .1.3.6.1.4.1.449.2.1.2.2.21.1.1 |
cdx6500VoiceSwitchRxDTMFDigitStringSelect the voice number plans for the 6520/6560 network.
The received DTMF digits received by the voice interface is
compared to this parameter.
- Enter a trailing asterisk(*) as a wild-card.
- Use the space bar to blank the parameter.
Range: 1 to 20 characters (valid characters are 0 through 9,
'-', ',', '/', and '*'). The characters '-', ',', and '/'
are allowed only for ease of reading. They are not sent to the
remote port.
Note: The maximum number of digits that can be sent
to the remote end is 16.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.21.1.1.1 |
cdx6500VoiceSwitchNumRxDigitToReceiveSelect the number of DTMF digits to
be received before making the call request.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.21.1.1.2 |
cdx6500VoiceSwitchCallParamDefine the network address of the called
node and the port or Hunt Group number
of the desired destination port.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.21.1.1.3 |
cdx6500VoiceSwitchAlternateDestinationThis object is no longer supported.rodeprecated Enumeration .1.3.6.1.4.1.449.2.1.2.2.21.1.1.4 |
cdx6500VoiceSwitchCompressionOverrideRateSelect the voice compression override algorithm.
none - No override, use port configured value.
c8k - 8k CVSELP
c16k - 16k CVSELP
cB8k - Bundled 8k CVSELP
cB16k - Bundled 16k CVSELP
cE8Kb - Enhanced Bundled 8k CVSELP
cE8Kb - Enhanced Bundled 16k CVSELP
nc - Skipped during configuration.ro Enumeration .1.3.6.1.4.1.449.2.1.2.2.21.1.1.5 |
cdx6500VoiceSwitchNumLeadingDigitToStripSelect the number of leading digits to
be stripped off the received digits stream
before sending the digits stream to the
remote port.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.21.1.1.6 |
cdx6500VoiceSwitchPreFixDigitsSelect digits to be added in front of or at the end
of the received stream (after the stripped digits are
removed) before sending the digit stream to the remote port.
Range: 1 to 20 characters (valid characters are 0 through 9,
'*', '#', 'R', 'P', and '-'). The character '-' is allowed
only for ease of reading. It is not sent to the remote port.
The 'P' character is used to indicate a pause is required in
the playout of the digits at the remote end. The length of
the pause is equal to 'Tx Interdigit Pause Time' as defined
at the called port (destination port). Leading 'P' characters
are not supported. The character 'R' is used to separate the
prefix digit string from the postfix digit string
Note: The maximum number of digits that can be sent
to the remote end is 16.ro DisplayString .1.3.6.1.4.1.449.2.1.2.2.21.1.1.7 |
cdx6500VoiceSwitchPostFixDigitsSelect DTMF digits to be added at the end of the received DTMF
stream before sending the digit stream to the remote port.
Range: 1 to 20 characters (valid characters are 0 through 9,
'-', ',', '/', '*', '#', and 'P'). The characters '-', ',',
and '/' are allowed only for ease of reading. They are not
sent to the remote port. The 'P' character is used to indicate
a pause is required in the playout of the digits at the remote
end. The length of the pause is equal to 'Tx Interdigit
Pause Time' as defined at the called port (destination port).
Note: The maximum number of digits that can be sent
to the remote end is 16.
This object is no longer supported.rodeprecated DisplayString .1.3.6.1.4.1.449.2.1.2.2.21.1.1.8 |
cdx6500VoiceSwitchEntryNumberThis is the entry number in the Voice Switch Table.ro INTEGER .1.3.6.1.4.1.449.2.1.2.2.21.1.1.9 |
cdx6500Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3 |
cdx6500StatProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1 |
cdx6500PSTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1.1 |
cdx6500PSTVoicePortTable OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1.1.26 |
cdx6500PPSTVoicePortTableThis table contains the port statistics for Voice ports. SEQUENCE OF Cdx6500PPSTVoicePortEntry .1.3.6.1.4.1.449.2.1.3.1.1.26.1 |
cdx6500PPSTVoicePortEntryA Voice Port Statistics Table Entry. Each entry contains
the statistics for a single Voice Port. Cdx6500PPSTVoicePortEntry .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1 |
cdx6500VoiceStatsPortNumberPort number of the Voice Port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.1 |
cdx6500VoiceStatsPortInterfaceTypeThis parameter indicates the type of DPSM card used.
eAndM2 : DPSM/E&M.
eAndM4 : DPSM/E&M.
fxo : DPSM/HC(FXO).
fxs : DPSM/FXS.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.2 |
cdx6500VoiceStatsHWRevAndPartNumberHardware revision and part number of the main card. The
revision number has format n.n and the part number is an 8
digit number of the form nnnnnnnn.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.3 |
cdx6500VoiceStatsFortyEightVoltsThis parameter indicates whether the 48 volt power supply is
installed in the node.
none : power supply not installed.
present : power supply installed.
na : Value not available.
This parameter will not be displayed for DSPM/HC.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.4 |
cdx6500VoiceStatsPortStateThis parameter indicates ths status of the port.
disabled : The port is disabled.
enabled : The port is enabled.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.5 |
cdx6500VoiceStatsCircuitStateThis parameter indicates the state of the SVC associated
with this port.
connected : SVC established.
disconnected : SVC not established.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.6 |
cdx6500VoiceStatsCurrentModeThis parameter indicates the current operating mode
of the DSP.
voice : DSP is currently operating in voice mode.
pcm : PCM mode is not supported.
fax : DSP is currently operating in fax mode.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.7 |
cdx6500VoiceStatsTimeOfLastStatResetThis parameter indicates the time since the last statistic
reset using the format month:day:year:hours:minutes:seconds
(mm:dd:yyyy:hh:mm:ss).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.8 |
cdx6500VoiceStatsCallDurationThis parameter indicates the duration of the current (last)
call using the format hours:minutes:seconds (hh:mm:ss).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.9 |
cdx6500VoiceStatsTotalCallDurationThis parameter indicates the total time of all calls since
last reset.It is measured from Offhook to Onhook and uses
the format hours:minutes:seconds (hh:mm:ss).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.10 |
cdx6500VoiceStatsPortUtilizationThis parameter is calculated as the ratio of `Total Call
Duration' to `Time Of Last Reset'. It is a percentage
value of the form nnn%.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.11 |
cdx6500VoiceStatsNumberOfCallsThis parameter indicates the total number of calls since the
last reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.12 |
cdx6500VoiceStatsLastDigitsTransmittedThis parameter indicates the last DTMF digits transmitted to
the voice interface. Not supported at this time.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.13 |
cdx6500VoiceStatsLastDigitsReceivedThis parameter indicates the last DTMF digits received from
the voice interface. Not supported at this time.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.14 |
cdx6500VoiceStatsTxPacketDroppedThis parameter indicates the number of times transmit packets
were dropped due to DSPM congestion.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.15 |
cdx6500VoiceStatsRxPacketDroppedThis parameter indicates the number of times receive packets
were dropped due to network overload or processor loading.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.16 |
cdx6500VoiceStatsDroppedPacketsThis parameter indicates the estimate of packets dropped
end to end in the network.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.17 |
cdx6500VoiceStatsDSPInternalFaultsThis parameter indicates the number of recoverable software
faults.It is displayed only when the DEBUG flag is set.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.18 |
cdx6500VoiceStatsTxPacketsThis parameter indicates the number of packets received from
the network port since the last reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.19 |
cdx6500VoiceStatsRxPacketsThis parameter indicates the number of packets sent to the
network port since the last reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.20 |
cdx6500VoiceStatsTxPacketsPerSecondThis parameter indicates the average number of packets
transmitted per second.It is calculated as the ratio of `Tx
Packets' to `Total Call Duration'.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.21 |
cdx6500VoiceStatsRxPacketsPerSecondThis parameter indicates the average number of packets
received per second.It is calculated as the ratio of `Rx
Packets' to `Total Call Duration'.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.22 |
cdx6500VoiceStatsDSIEfficiencyThis parameter is calculated by dividing `Rx Packets/sec'
by the packet rate. It is a percentage value.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.23 |
cdx6500VoiceStatsCurrentRateThis parameter indicates the current compression rate
being used.
cD8K : Compression rate is 8K.
cBD8K : Compression rate is bundled 8K.
cE8Kb : Compression rate is Enhanced bundled D8K.
cD16K : Compression rate is 16K.
cBD16K : Compression rate is bundled 16K.
cE16Kb : Compression rate is Enhanced bundled D16K.
cPcm : Compression rate is PCM.
cFax : Compression rate is FAX.
na : Value not available.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.24 |
cdx6500VoiceStatsInputPowerThis parameter indicates the input power level in dBm.
(Measured power).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.25 |
cdx6500VoiceStatsOutputPowerThis parameter indicates the output power level in dBm.
(Measured power).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.26 |
cdx6500VoiceStatsFAXTransmissionsThis parameter indicates the number of FAX
transmissions spoofed.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.27 |
cdx6500VoiceStatsUnsupportedFmtsFAXXmissionsThis parameter indicates the number of FAX transmissions
requesting unsupported formats but transmitted using
ISG formats.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.28 |
cdx6500PPSTSignalingSequenceTrapTxStateThe transmitting voice signalling state is displayed
as ABCD (i.e. 1010).
This object is no longer supported. Refer to
cdx6500SignalingSequenceTrapTxState.rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.29 |
cdx6500PPSTSignalingSequenceTrapRxStateThe receiving voice signalling state is displayed
as ABCD (i.e. 1010).
This object is no longer supported. Refer to
cdx6500SignalingSequenceTrapRxState.rodeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.30 |
cdx6500PPSTSignalingSequenceTrapMachineStateThe voice signalling state machine state is a 11 character
field representing the state of the signalling software.
This object is no longer supported. Refer to
cdx6500SignalingSequenceTrapMachineState.rodeprecated DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.31 |
cdx6500PPSTSignalingSequenceTrapTimeSinceLastChangeThis parameter indicates the time from the previous state to
this state, measured in milliseconds.
This object is no longer supported. Refer to
cdx6500SignalingSequenceTrapTimeSinceLastChange.rodeprecated INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.32 |
cdx6500PPSTSignalingSequenceTrapCommentThe comment field is an ASCII string upto 16 characters long.
This object is no longer supported. Refer to
cdx6500SignalingSequenceTrapComment.rodeprecated DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.33 |
cdx6500VoiceStatsCurrentStatusThis is the call processing state machine status.
inhibited : Current Status = Disconnected.
disconnected : Current Status = Disconnected.
calling : Current Status = Calling.
called : Current Status = Called.
connected : Current Status = Connected (data transfer).
null : Current Status = Undefined.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.34 |
cdx6500VoiceStatsLastClearCauseCodeThis parameter indicates the last clear cause code received
Every code corresponds to an integer value followed by its
text description in paranthesis. eg.Consider the clear
cause code for `number busy' which is CAUSE-CLR-NUM-BSY.
This corresponds to : 001 (number busy).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.35 |
cdx6500VoiceStatsLastClearDiagnosticCodeThis parameter indicates the last clear diagnostic
received.Every code corresponds to an integer value followed
by its text description in paranthesis. eg.Consider
the diagnostic code for `invalid bits in packet' which is
DIAG-INV-PKT-BITS.This corresponds to :041 (invalid bits
in packet).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.36 |
cdx6500VoiceStatsLastInboundCallPacketCalledAddressThis parameter contains the called address present in the
last inbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.37 |
cdx6500VoiceStatsLastInboundCallPacketCallingAddressThis parameter contains the calling address present in the
last inbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.38 |
cdx6500VoiceStatsLastInboundCallPacketFacilitiesThis parameter contains the facilities present in the last
inbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.39 |
cdx6500VoiceStatsLastInboundCallPacketCUDThis parameter contains the call user data present in the
last inbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.40 |
cdx6500VoiceStatsLastOutboundCallPacketCalledAddressThis parameter contains the called address present in the
last outbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.41 |
cdx6500VoiceStatsLastOutboundCallPacketCallingAddressThis parameter contains the calling address present in the
last outbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.42 |
cdx6500VoiceStatsLastOutboundCallPacketFacilitiesThis parameter contains the facilities present in the last
outbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.43 |
cdx6500VoiceStatsLastOutboundCallPacketCUDThis parameter contains the call user data present in the
last outbound call packet.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.44 |
cdx6500VoiceStatsRingerStatusThis parameter indicates the Ringer status on the board.
It is displayed only for DSPM/FXS interfaces.
rs25Hz : 25Hz Ringer status on board.
rs50Hz : 50Hz Ringer status on board.
na : Value not available.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.45 |
cdx6500VoiceStatsDSPMSMSlotNumberThis parameter indicates the slot of the DSPM/SM. It is
displayed only for DSPM/SM interfaces. A value of 0
indicates that this parameter is not available.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.46 |
cdx6500VoiceStatsDSPMNumberThis parameter indicates the DSP used for the virtual
port.It is displayed only for DSPM/SM interfaces. A value
of 0 indicates that this parameter is not available.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.47 |
cdx6500VoiceStatsT1E1PortNumberThis is the port number of the T1 or E1 port this voice
channel is on.It is displayed only for DSPM/SM interfaces.
A value of 0 indicates that this parameter is not available.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.48 |
cdx6500VoiceStatsTimeSlotNumberThis parameter indicates the time slot number. It is
displayed only for DSPM/SM interfaces. For multiple
time slots it will be displayed as 1,2-5,..ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.49 |
cdx6500VoiceStatsDaughterCardRevAndPartNumberHardware revision and part number of the daughter card.The
revision number has format n.n and the part number is an 8
digit number of the form nnnnnnnn.It is displayed only for
DSPM/HC interfaces.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.50 |
cdx6500VoiceStatsVADEfficiencyVAD (Voice Activity Detection) Efficiency shows you the
percentage of VAD efficiency. It is displayed only for
DSPM/FX interfaces. A value of 0 indicates that this
parameter is not available.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.51 |
cdx6500VoiceStatsMeanDelayDeviationThis parameter shows you Mean Delay Deviation. It is
displayed only for DSPM/FX interfaces. A value of 0
indicates that this parameter is not available.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.52 |
cdx6500VoiceStatsMaxDelayDeviationThis parameter shows you Max Delay Deviation in the
way of Max Delay Deviation/Max Delay Dev Highwater.
It is displayed only for DSPM/FX interfaces. A value
of 0 indicates that this parameter is not available.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.53 |
cdx6500VoiceStatsPktRecResyncThis parameter shows you Receiver Resets. It is
displayed only for DSPM/FX interfaces. A value of 0
indicates that this parameter is not available.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.54 |
cdx6500VoiceCallStatsNoPacketDroppedIt is the number of dropped packet occurred during the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.55 |
cdx6500VoiceCallStatsNoCallsDroppedIt is the number of dropped calls occurred during the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.56 |
cdx6500VoiceCallStatsDroppedReason0It is the number of dropped cause code 0,
[originated by DTE; no info], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.57 |
cdx6500VoiceCallStatsDroppedReason1It is the number of dropped cause code 1,
[number busy], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.58 |
cdx6500VoiceCallStatsDroppedReason3It is the number of dropped cause code 3,
[invalid facility request], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.59 |
cdx6500VoiceCallStatsDroppedReason5It is the number of dropped cause code 5,
[network congestion], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.60 |
cdx6500VoiceCallStatsDroppedReason9It is the number of dropped cause code 9,
[out of order], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.61 |
cdx6500VoiceCallStatsDroppedReason11It is the number of dropped cause code 11,
[access barred], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.62 |
cdx6500VoiceCallStatsDroppedReason13It is the number of dropped cause code 13,
[not obtainable], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.63 |
cdx6500VoiceCallStatsDroppedReason17It is the number of dropped cause code 17,
[remote procedure error], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.64 |
cdx6500VoiceCallStatsDroppedReason19It is the number of dropped cause code 19,
[local procedure error], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.65 |
cdx6500VoiceCallStatsDroppedReason21It is the number of dropped cause code 21,
[RPOA out of order], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.66 |
cdx6500VoiceCallStatsDroppedReason33It is the number of dropped cause code 33,
[incompatible destination], upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.67 |
cdx6500VoiceCallStatsDroppedReason-RestIt is the number of the rest of dropped cause codes
upto the last 24 hours.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.1.1.68 |
cdx6500PPSTSignalingSequenceTrapTableA table containing the Signaling Sequence Trap entries. SEQUENCE OF Cdx6500PPSTSignalingSequenceTrapEntry .1.3.6.1.4.1.449.2.1.3.1.1.26.2 |
cdx6500PPSTSignalingSequenceTrapEntryAn entry in the Signaling Sequence Trap table. Cdx6500PPSTSignalingSequenceTrapEntry .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1 |
cdx6500SignalingSequenceTrapPortNumberPort number of the Voice Port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.1 |
cdx6500SignalingSequenceTrapEventNumberEvent number in the Signaling Sequence Trap Entry.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.2 |
cdx6500SignalingSequenceTrapTxStateThe transmitting voice signalling state is displayed
as ABCD (i.e. 1010).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.3 |
cdx6500SignalingSequenceTrapRxStateThe receiving voice signalling state is displayed
as ABCD (i.e. 1010).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.4 |
cdx6500SignalingSequenceTrapMachineStateThe voice signalling state machine state is a 11 character
field representing the state of the signalling software.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.5 |
cdx6500SignalingSequenceTrapTimeSinceLastChangeThis parameter indicates the time from the previous state to
this state, measured in milliseconds.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.6 |
cdx6500SignalingSequenceTrapCommentThe comment field is an ASCII string upto 16 characters long.ro DisplayString .1.3.6.1.4.1.449.2.1.3.1.1.26.2.1.7 |
cdx6500StatNetworkSvcsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.4 |
cdx6500StatVCSTableThis table is showing the Voice Call Statistics in a node that
would allow a user to determine current and past perfrmance. SEQUENCE OF Cdx6500StatVCSEntry .1.3.6.1.4.1.449.2.1.3.4.4 |
cdx6500StatVCSEntryA list of objects describing a single VCS. Cdx6500StatVCSEntry .1.3.6.1.4.1.449.2.1.3.4.4.1 |
cdx6500StatVCSIndexIt is time position in the list of VCS's.ro INTEGER .1.3.6.1.4.1.449.2.1.3.4.4.1.1 |
cdx6500StatVCSTimeIt is displaying the corresponding time to index in the list of VCS's.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.4.4.1.2 |
cdx6500StatVCSNoPacketDroppedIt is the number of dropped packet occurred during the time.ro INTEGER .1.3.6.1.4.1.449.2.1.3.4.4.1.3 |
cdx6500StatVCSNoCallsDroppedIt is the number of dropped calls occurred during the time.ro INTEGER .1.3.6.1.4.1.449.2.1.3.4.4.1.4 |
cdx6500StatVCSDroppedReasonsIt is the number of 12 possible reasons from x25-causes.
(Rsn0/Rsn1/Rsn3/Rsn5/Rsn9/Rsn11/Rsn13/Rsn17/Rsn19/Rsn21/Rsn33/Rsn-Rest)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.4.4.1.5 |
cdx6500StatVCSNoCallsProcessedIt is the number of all voice calls processed.ro INTEGER .1.3.6.1.4.1.449.2.1.3.4.4.1.6 |
cdx6500StatVCSPercentPeakAvgCurOfCPULoadIt is the value of Peak, Average and Currentof CPU load in percent.
(Peak/Avg/Cur)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.4.4.1.7 |
cdx6500StatVCSPercentPeakAvgCurOfDataBufIt is the value of Peak, Average and Current of Data Buffer in percent.
(Peak/Avg/Cur)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.4.4.1.8 |
cdx6500StatVCSPercentPeakAvgCurOfIORBBufIt is the value of Peak, Average and Current of IORB Buffer in percent.
(Peak/Avg/Cur)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.449.2.1.3.4.4.1.9 |
cdx6500Controls OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.4 |