UBQS-IP-MIB
AI MIB Summary
The UBQS-IP-MIB module enables monitoring and management of IP layer attributes, including interface status, address configurations, and routing table entries, specifically for Ubiquiti Networks (UBNT) UniFi and EdgeRouter hardware. It facilitates the retrieval of standard IP statistics such as packet counts, error rates, and fragmentation metrics via SNMP to support network performance analysis and fault isolation.
This MIB module defines IP information.
Main OID:
ubiIpMIB.1.3.6.1.4.1.7800.100.14
65
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
65 total| Object Name |
|---|
ubiIpMIBThis MIB module defines IP information. MODULE-IDENTITY .1.3.6.1.4.1.7800.100.14 |
ubiIpMIBNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.0 |
ubiIpMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.0.1 |
ubiPingMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.0.2 |
ubiPingSendCompletionThis notification is sent at the completion
of the sequence of pings. NOTIFICATION-TYPE .1.3.6.1.4.1.7800.100.14.0.2.1 |
ubiIpMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.1 |
ubiIpAddrTableThe table of addressing information relevant to
this entity's IP addresses. SEQUENCE OF UbiIpAddrEntry .1.3.6.1.4.1.7800.100.14.1.1 |
ubiIpAddrEntryThe addressing information for one of this
entity's IP addresses. UbiIpAddrEntry .1.3.6.1.4.1.7800.100.14.1.1.1 |
ubiIpAddrTypeThe IP address type.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.1.1.1 |
ubiIpAddressThe IP address to which this entry's addressing
information pertains.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.1.1.2 |
ubiIpAddrPrefixLenThe prefix length associated with the IP address.ro InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.1.1.3 |
ubiIpAddrIfIndexThe index value which uniquely identifies
the interface to which this entry is applicable.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.7800.100.14.1.1.1.4 |
ubiIpAddrStatusIndicate whether this entry is primary or not.rw Enumeration .1.3.6.1.4.1.7800.100.14.1.1.1.5 |
ubiIpAddrRowstatusThis object is used to create a new row or
delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.1.1.1.6 |
ubiInetRouteTableThe table of addressing information relevant to
this entity's IP addresses. SEQUENCE OF UbiInetRouteEntry .1.3.6.1.4.1.7800.100.14.1.2 |
ubiInetRouteEntryThe addressing information for one of this
entity's IP addresses. UbiInetRouteEntry .1.3.6.1.4.1.7800.100.14.1.2.1 |
ubiInetRouteInstanceThe instance identifier of the (conceptual) routing table
containing this route.ro Unsigned32 .1.3.6.1.4.1.7800.100.14.1.2.1.1 |
ubiInetRouteDestTypeThe destination address type.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.2.1.2 |
ubiInetRouteDestThe destination IP address of this route.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.2.1.3 |
ubiInetRouteDestPfxLenro InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.2.1.4 |
ubiInetRouteNextHopTypero InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.2.1.5 |
ubiInetRouteNextHopro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.2.1.6 |
ubiInetRouteIfIndexro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.7800.100.14.1.2.1.7 |
ubiInetRoutetypero Enumeration .1.3.6.1.4.1.7800.100.14.1.2.1.8 |
ubiInetRouteProtoro Enumeration .1.3.6.1.4.1.7800.100.14.1.2.1.9 |
ubiInetRouteMetric1ro Integer32 .1.3.6.1.4.1.7800.100.14.1.2.1.10 |
ubiInetRouteMetric2ro Integer32 .1.3.6.1.4.1.7800.100.14.1.2.1.11 |
ubiInetRouteMetric3ro Integer32 .1.3.6.1.4.1.7800.100.14.1.2.1.12 |
ubiInetRouteMetric4ro Integer32 .1.3.6.1.4.1.7800.100.14.1.2.1.13 |
ubiInetRouteMetric5ro Integer32 .1.3.6.1.4.1.7800.100.14.1.2.1.14 |
ubiInetRouteStatusro Enumeration .1.3.6.1.4.1.7800.100.14.1.2.1.15 |
ubiInetRouteDistancerw Integer32 .1.3.6.1.4.1.7800.100.14.1.2.1.16 |
ubiInetRouteTagrw Unsigned32 .1.3.6.1.4.1.7800.100.14.1.2.1.17 |
ubiInetRouteNextHopNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.1.2.1.18 |
ubiInetRouteRowstatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.1.2.1.19 |
ubiIpv6NeighborTableThe table of addressing information relevant to
this entity's IPv6 addresses. SEQUENCE OF UbiIpv6NeighborEntry .1.3.6.1.4.1.7800.100.14.1.3 |
ubiIpv6NeighborEntryThe addressing information for one of this
entity's IPv6 addresses. UbiIpv6NeighborEntry .1.3.6.1.4.1.7800.100.14.1.3.1 |
ubiIpv6NeighborIfIndexThe inde value which uniquely identifies
the interface to which this entry is applicablero InterfaceIndex (IF-MIB) .1.3.6.1.4.1.7800.100.14.1.3.1.1 |
ubiIpv6NeighborPhysAddressThe media-dependent `physical' address. This object should
return 0 when this entry is in the 'incomplete' state.
As the entries in this table are typically not persistent
when this object is written the entity should not save the
change to non-volatile storage. Note: a stronger
requirement is not used because this object was previously
defined.rw PhysAddress .1.3.6.1.4.1.7800.100.14.1.3.1.2 |
ubiIpv6NeighborNetAddressThe Ipv6Address corresponding to the media-dependent
`physical' address.
This object predates the rule limiting index objects to a
max access value of 'not-accessible' and so continues to use
a value of 'read-create'.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7800.100.14.1.3.1.3 |
ubiIpv6NeighborTypeThe type of mapping.
Setting this object to the value invalid(2) has the effect
of invalidating the corresponding entry in the
ubiIpv6NeighborTable. That is, it effectively dis-associates
the interface identified with said entry from the mapping
identified with said entry. It is an implementation-
specific matter as to whether the agent removes an
invalidated entry from the table. Accordingly, management
stations must be prepared to receive tabular information
from agents that corresponds to entries not currently in
use. Proper interpretation of such entries requires
examination of the relevant ubiIpv6NeighborType object.
As the entries in this table are typically not persistent
when this object is written the entity should not save the
change to non-volatile storage. Note: a stronger
requirement is not used because this object was previously
defined.ro Enumeration .1.3.6.1.4.1.7800.100.14.1.3.1.4 |
ubiIpv6NeighborStateThe Neighbor Unreachability Detection [3] state for the
interface when the address mapping in this entry is used.
If Neighbor Unreachability Detection is not in use,
this object is always unknown(6).ro Enumeration .1.3.6.1.4.1.7800.100.14.1.3.1.5 |
ubiIpv6NeighborLastUpdatedThe value of sysUpTime at the time this entry was last
updated. If this entry was updated prior to the last re-
initialization of the local network management subsystem,
then this object contains a zero value.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.1.3.1.6 |
ubiIpv6NeighborRowstatusThe status of this conceptual row.
As all objects in this conceptual row have default values, a
row can be created and made active by setting this object
appropriately.
The RowStatus TC requires that this DESCRIPTION clause
states under which circumstances other objects in this row
can be modified. The value of this object has no effect on
whether other objects in this conceptual row can be
modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.1.3.1.7 |
ubiPingMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.2 |
ubiPingGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.2.1 |
ubiPingSend OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.2.2 |
ubiPingSendProtoThe protocol to use.rw Enumeration .1.3.6.1.4.1.7800.100.14.2.2.1 |
ubiPingSendTargetThe address of the device to be pinged.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.2.2.2 |
ubiPingSendRepeatSpecifies the number of ping packets to send
to the target.rw Integer32 .1.3.6.1.4.1.7800.100.14.2.2.3 |
ubiPingSendPacketSizeSpecifies the size of ping packets to send
to the target.rw Integer32 .1.3.6.1.4.1.7800.100.14.2.2.4 |
ubiPingSendTimeoutSpecifies the amount of time to wait for a response.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.7800.100.14.2.2.5 |
ubiPingSendIntervalSpecifies the amount of time to wait before
sending the next packet.rw Integer32 UNITS "seconds" .1.3.6.1.4.1.7800.100.14.2.2.6 |
ubiPingSendSrcAddrSpecifies the sender IP address for sending packets.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.2.2.7 |
ubiPingSendTTLSpecifies the TTL.rw Integer32 .1.3.6.1.4.1.7800.100.14.2.2.8 |
ubiPingSendTosSpecifies the Type Of Service.rw Integer32 .1.3.6.1.4.1.7800.100.14.2.2.9 |
ubiPingSendDFSpecifies the DF bit in IP header. dont(2) means
a packet cannot be fragmented.rw Enumeration .1.3.6.1.4.1.7800.100.14.2.2.10 |
ubiPingSendExecuteSend the ping packets when value is set to
send(1).rw Enumeration .1.3.6.1.4.1.7800.100.14.2.2.15 |
ubiPingResults OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.2.3 |
ubiPingSendCompletedSet to true when all the packets in this sequence have been
either responded to or timed out.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7800.100.14.2.3.1 |
ubiPingSendPacketsThe total number of the sending ping.ro Counter32 .1.3.6.1.4.1.7800.100.14.2.3.2 |
ubiPingReceivedPacketsThe total number of the received ping.ro Counter32 .1.3.6.1.4.1.7800.100.14.2.3.3 |
ubiIpMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.3 |
ubiIpMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.3.1 |
ubiIpMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.7800.100.14.3.2 |