TelcoReturnCABLE-DEVICE-MIB
AI MIB Summary
The TelcoReturnCABLE-DEVICE-MIB enables monitoring and management of Data Over Cable Access Service (DOCSIS) return path parameters, including signal quality, noise levels, and upstream channel statistics, for cable modems and termination systems. This module facilitates the tracking of physical layer metrics such as signal-to-noise ratio (SNR), transmit power, and error counters to diagnose upstream connectivity issues in hybrid fiber-coaxial networks.
TELCO Return MIB for Data Over Cable Access modems and termination systems
Main OID:
docsTrCmMIB.1.3.6.1.2.1.10.128
53
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
53 total| Object Name |
|---|
docsTrCmMIBTELCO Return MIB for Data Over Cable Access
modems and termination systems MODULE-IDENTITY .1.3.6.1.2.1.10.128 |
docsTrCmCapabilityThis object represents the CM Capability. A CM
may be'TelcoReturn(2)', or 'TwoWay(3)', or Other e.g.,
undefinedro Enumeration .docsTrCmBase.1 |
docsTrCmModeThis object represents the CM Operating Mode. A
CM may be operating as'TelcoReturn(2)', or 'TwoWay(3)', or
Other e.g, undefinedrw Enumeration .docsTrCmBase.2 |
docsTrCmCdCodeThe value of this object indicates a further
description of what went wrong when a command fails.ro Enumeration .docsTrCmCommand.1 |
docsTrCmCdMgtStationIdThis object is a generic read-write variable
that a Management Station (MS) can use to guarantee that the
results from a given command are the results of a command
issued by that specific MS. Each MS must SET a unique value
to this object when doing commands and GET the value of this
object together with docsTrCmCdResult and docsTrCmCdReqId
to detect interference from other MSs.rw OCTET STRING .docsTrCmCommand.2 |
docsTrCmCdReqIdThis object contains the request ID field of the
SNMP PDU which invoked the most recent command on the
telephony return modem, if the request-id is unknown or
undefined, the object contains the value zerorw INTEGER .docsTrCmCommand.3 |
docsTrCmCdResultThis object can contain parameters that are raw
results to the particular command being issued.rw OCTET STRING .docsTrCmCommand.4 |
docsTrCmCdForceIn certain cases the telephony return modem may
be in a state where certain commands could adversely affect
connections. In such cases, a command request with this
object not present or set to 'false(2)' will result in a
warning. If the operator elects to ignore such warnings,
this object can be set to force 'true(1)' in a subsequent
request to cause the command to be carried out regardless of
the potentially hazardous effect.rw TruthValue (SNMPv2-TC) .docsTrCmCommand.5 |
docsTrCmCdScriptThis object can contain parameters that
specifically define a particular command or series of
commands being issued directly to the dial modem. Script
execution depends upon the inclusion in this string of a
suitable escape sequence (usually +++) to enter a dial modem
into a command mode.rw OCTET STRING .docsTrCmCommand.6 |
docsTrCmCdStatusThis object contains the result of the most
recently requested command or test, or the value none(1) if
no commands have been requested since last reset.ro Enumeration .docsTrCmCommand.7 |
docsTrTsSPD OBJECT IDENTIFIER .docsTrCmMIBObjects.3 |
docsTrTsSPDTableA table of all the SPD messages that get sent
out SEQUENCE OF DocsTrTsSPDEntry .docsTrCmMIBObjects.3.1 |
docsTrTsSPDEntryThis an entry in the SPD table which is one of
the SPD that get sent outto the cable modems DocsTrTsSPDEntry .docsTrCmMIBObjects.3.1.1 |
docsTrTsSPDindexThe unique number which identifies the Service
Provider Descriptor in the SPDTable INTEGER .docsTrCmMIBObjects.3.1.1.1 |
docsTrTsSPDnameThe name of the Service Provider. A value of
null string means no namerw DisplayString .docsTrCmMIBObjects.3.1.1.2 |
docsTrTsSPDphoneNum1The first phone number to try when trying to
reach the service provider. A value of null string means no
phone numberrw DisplayString .docsTrCmMIBObjects.3.1.1.3 |
docsTrTsSPDphoneNum2The second phone number to try to reach the
service provider when the first number fails. A value of
null string means no phone numberrw DisplayString .docsTrCmMIBObjects.3.1.1.4 |
docsTrTsSPDphoneNum3The third phone number to try in case the 1st
and 2nd numbers fail. A value of null string means no phone
numberrw DisplayString .docsTrCmMIBObjects.3.1.1.5 |
docsTrTsSPDConnThresholdThe number of sequential connection try failures
before indicating connection failure.rw Integer32 .docsTrCmMIBObjects.3.1.1.6 |
docsTrTsSPDuserNameThe username the CM will use during PAP or CHAP
authentication over telco link during the initialization
procedure.rw DisplayString .docsTrCmMIBObjects.3.1.1.7 |
docsTrTsSPDuserPasswordThe password that the CM will use during the PAP
or CHAP authentication over the telco link during the
initialization procedure.rw OCTET STRING .docsTrCmMIBObjects.3.1.1.8 |
docsTrTsSPDpppAuthThis instructs the telco return modem of the
authentication procedure to perform over the telco link.rw Enumeration .docsTrCmMIBObjects.3.1.1.9 |
docsTrTsSPDdhcpAuthBoolean value reserved to indicate CM MUST
authenticate DHCP messages when enable.rw TruthValue (SNMPv2-TC) .docsTrCmMIBObjects.3.1.1.10 |
docsTrTsSPDradiusRealmThe realm name contains the ASCII string which
defines a RADIUS server domain. TRAC RADIUS MUST proxy
requests to a server realm. RADIUS syntax is to address
login name as Username- String@Realm-String - RADIUS Realm-
String MUST be correlated by the TRAC RADIUS to the IP
address of a RADIUS server to be proxied to for the
designated RADIUS user profile. If the TRAC RADIUS is the
server for designated user profile,the default value is the
null string.rw DisplayString .docsTrCmMIBObjects.3.1.1.11 |
docsTrTsDemandDialTimerThis object represents the number of seconds of
networking inactivity allowed before hang-up, the default
zero indicates demand dial is not enabled. Demand dial is
desirable to allow the traffic engineering of dial-in ports.
Networking activity monitoring is a vendor specific
implementationrw Unsigned32 .docsTrCmMIBObjects.3.1.1.12 |
docsTrTsSPDdhcpAddressThe ip address of the DHCP server.rw IpAddress .docsTrCmMIBObjects.3.1.1.13 |
docsTrTsSPDfactoryDefboolean value, if true, indicates the SPD which
SHOULD be used by the CM during factory default procedure.rw TruthValue (SNMPv2-TC) .docsTrCmMIBObjects.3.1.1.14 |
docsTrTsSPDstatusWhen the status is set to disabled, that
corresponding SPD entry will be disabled from the CMTS. When
the status is set to enabled, that corresponding SPD entry
will be enabled in the CMTS. When the status is set to
deleted, that corresponding SPD entry will be deleted from
the CMTS. At least one SPD entry must be present and enabled
in a CMTSrw Enumeration .docsTrCmMIBObjects.3.1.1.15 |
docsTrCmPingAuthThis object has a value of 'true(1)' if CPE is
allowed to generate ping (ICMP request) across the network,
CPE.rw TruthValue (SNMPv2-TC) .docsTrCmSessionBase.1 |
docsTrCmTerminateOnOffHookThis object has a value of 'true(1)' if CM must
terminate data session on off hook/voice call eventsrw TruthValue (SNMPv2-TC) .docsTrCmSessionBase.2 |
docsTrCmCMTypeThis object represents the CM configured type. A
CM may be configured as a DOCSIS bridge 'ExtGeneric(1)', as
a telephony return IP forwarder 'ExtRouted(2)', or as a
single host 'InternalXXX(3-8).ro Enumeration .docsTrCmSessionBase.3 |
docsTrCmRingNoAnsThis object defines the number of rings before
answer a CM should allow (ring threshold) before failing the
connection as NO ANSWERrw INTEGER .docsTrCmSessionBase.4 |
docsTrCmWaitIntervalThis object defines the number of seconds of
time CM should wait for a call to ring after dialingro Unsigned32 .docsTrCmSessionBase.5 |
docsTrCmSPDpersistEnabletruth value contains interpretation of the SPD
MIB objects for the CM local ISP selection method. If
docsTrCmSPDpersistEnable is false (2), no SPD MIB objects
persist in an active SPD if ANY SPD parameters are set in a
TFTP configuration file. In such a case the CM MUST use only
configuration file SPD settings and defaults to construct
the active SPD. When docsTrCmSPDpersistEnable is true(1),
SPD MIB objects persist in an active SPD except where
specific SPD parameters in a TFTP configuration file
override their corresponding specific SPD MIB objects. In
such a case the CM MUST first use the configuration file SPD
settings, then use ANY SPD MIB object previously set where
TFTP configuration file parameters are not present, lastly,
appropriate defaults defined in [18,20] to construct the
active SPD. The initial setting is false(2).rw TruthValue (SNMPv2-TC) .docsTrCmSPDBase.1 |
docsTrCmSPDnameThis object contains the service provider Namerw DisplayString (SNMPv2-TC) .docsTrCmSPDBase.2 |
docsTrCmISPphoneNum1This object contains the Primary ISP Phone
number 1rw DisplayString (SNMPv2-TC) .docsTrCmSPDBase.3 |
docsTrCmISPphoneNum2This object contains the Backup Phone number 2rw DisplayString (SNMPv2-TC) .docsTrCmSPDBase.4 |
docsTrCmISPphoneNum3This object contains the Backup Phone number
3rw DisplayString (SNMPv2-TC) .docsTrCmSPDBase.5 |
docsTrCmconnThresholdThe number of sequential connection try failures
before indicating connection failure.rw Integer32 .docsTrCmSPDBase.6 |
docsTrCmPPPloginNameThis object contains the PPP Login Namerw DisplayString (SNMPv2-TC) .docsTrCmSPDBase.7 |
docsTrCmPPPpasswordThis object contains the PPP Passwordrw DisplayString (SNMPv2-TC) .docsTrCmSPDBase.8 |
docsTrCmPPPauthThis object contains the secure login
verification methodrw Enumeration .docsTrCmSPDBase.9 |
docsTrCmDHCPauthThis object contains the DHCP Server IP Addressrw IpAddress .docsTrCmSPDBase.10 |
docsTrCmradiusRealmThis object contains the RADIUS Cable Access
Realm Namerw DisplayString (SNMPv2-TC) .docsTrCmSPDBase.11 |
docsTrCmdemandDialTimerThis object represents the number of seconds of
networking inactivity allowed before hang-up, the default
zero indicates demand dial is not enabled. Demand dial is
desirable to allow the traffic engineering of dial-in ports.
Networking activity monitoring is a vendor specific
implementationrw Unsigned32 .docsTrCmSPDBase.12 |
docsTrCmDHCPserverThis object contains the DHCP Server IP Addressrw IpAddress .docsTrCmSPDBase.13 |
docsTrMsgBaseTableTelco Return Message Base Table SEQUENCE OF DocsTrMsgBaseEntry .docsTrMsgBase.1 |
docsTrMsgBaseEntryThis table contains the information
about TCD/TSI and USRbackOff for each interface DocsTrMsgBaseEntry .docsTrMsgBase.1.1 |
docsTrMsgIfIndexThe value corresponds to ifIndex for
either a CATV MAC or other network interface. In Cable
Modems, the default value is the customer side interface. In
Cable Modem Termination Systems, this object has to be
specified to create a row in this table. InterfaceIndexOrZero .docsTrMsgBase.1.1.1 |
docsTrMsgTCDIntervalThe interval between CMTS transmission of
successive Telephony Channel Descriptor (TCD) messages at
this interface.rw INTEGER .docsTrMsgBase.1.1.2 |
docsTrMsgTSIIntervalThe interval between CMTS transmission of
successive Termination System Interface (TSI) messages for a
downstream channel at this interface.This is also the time
interval a CM should scan on a specific channel for a TSI
message and sets the frequency the CM monitors the CMTS
epoch counter.rw INTEGER .docsTrMsgBase.1.1.3 |
docsTrMsgUSRBackOffThis object represents the number of times
CMTS will resend User Station Reset messages if
unacknowledged by CM; Number of duplicate reset requests CM
may receiverw Unsigned32 .docsTrMsgBase.1.1.4 |
docsTrMsgRowValueControls and reflects the status of rows in
this tablerw RowStatus (SNMPv2-TC) .docsTrMsgBase.1.1.5 |