TapeAlert-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TapeAlert-MIB.
104
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
104 total| Object Name |
|---|
hp OBJECT IDENTIFIER .1.3.6.1.4.1.11 |
RFC1155-SMI Unknown .1.3.6.1.4.1.11 |
nm OBJECT IDENTIFIER .1.3.6.1.4.1.11.2 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3 |
netPeripheral OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9 |
netTape OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.7 |
tapeAlert OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.7.1 |
tapeAlertTrap1The tape drive is having problems reading data. No
data has been lost, but there has been a reduction
in the performance of the tape. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.1 |
tapeAlertTrap2The tape drive is having problems writing data. No
data has been lost, but there has been a reduction
in the capacity of the tape. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.2 |
tapeAlertTrap3The operation has stopped because an error has
occured while reading or writing data which the
drive cannot correct. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.3 |
tapeAlertTrap4Your data is at risk:
1. Copy any data you require from this tape
2. Do not use this tape again
3. Restart the operation with a different tape TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.4 |
tapeAlertTrap5The tape is damaged or the drive is faulty.
Call the tape drive supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.5 |
tapeAlertTrap6The tape is from a faulty batch or the tape drive
is faulty:
1. Use a good tape to test the drive.
2. If the problem persists, call the tape drive
supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.6 |
tapeAlertTrap7The tape cartridge has reached the end of its
calculated useful life:
1. Copy any data you need to another tape
2. Discard the old tape. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.7 |
tapeAlertTrap8The tape cartridge is not data-grade.
Any data you back up to the tape is at risk.
Replace the cartridge with a data-grade tape. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.8 |
tapeAlertTrap9You are trying to write to a write-protected
cartridge. Remove the write-protection or use
another tape. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.9 |
tapeAlertTrap10You cannot eject the cartridge because the tape
drive is in use. Wait until the operation is
complete before ejecting the cartridge. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.10 |
tapeAlertTrap11The tape in the drive is a cleaning cartridge.
If you want to back up or restore, insert a
data-grade tape. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.11 |
tapeAlertTrap12You have tried to load a cartridge of a type
which is not supported by this drive. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.12 |
tapeAlertTrap13The operation has failed because the tape in the
drive has snapped:
1. Discard the old tape.
2. Restart the operation with a different tape. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.13 |
tapeAlertTrap14The operation has failed because the tape in the
drive has snapped:
1. Do not attempt to extract the tape cartridge.
2. Call the tape drive supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.14 |
tapeAlertTrap15The memory in the tape cartridge has failed, which reduces performance.
Do not use the cartridge for further backup operations. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.15 |
tapeAlertTrap16The operation has failed because the tape cartridge was
manually ejected while the tape drive was actively writing
or reading. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.16 |
tapeAlertTrap17You have loaded a cartridge of a type that is read-only in this drive.
The cartridge will appear as write-protected TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.17 |
tapeAlertTrap18The directory on the tape cartridge has been corrupted.
File search performance will be degraded. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.18 |
tapeAlertTrap19The tape cartridge is nearing the end of its useful life.
It is recommended that you:
1. Use another tape cartridge for your next backup.
2. Store this tape cartridge in a safe place in case you
need to restore data from it. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.19 |
tapeAlertTrap20The tape drive needs cleaning:
1. If the operation has stopped, eject the tape
and clean the drive
2. If the operation has not stopped, wait for it
to finish and then clean the drive.
Check the tape drive users manual for device
specific cleaning instructions. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.20 |
tapeAlertTrap21The tape drive is due for routine cleaning:
1. Wait for the current operation to finish.
2. Then use a cleaning cartridge.
Check the tape drive users manual for device
specific cleaning instructions. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.21 |
tapeAlertTrap22The last cleaning cartridge used in the tape
drive has worn out:
1. Discard the worn out cleaning cartridge.
2. Wait for the current operation to finish.
3. Then use a new cleaning cartridge. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.22 |
tapeAlertTrap23The last cleaning cartridge used in the tape drive was an invalid type:
1. Do not use this cleaning cartridge in this drive.
2. Wait for the current operation to finish.
3. Then use a valid cleaning cartridge. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.23 |
tapeAlertTrap29Preventive maintenance of the tape drive is required.
Check the tape drive users manual for device specific
preventive maintenance tasks or call the tape drive
supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.29 |
tapeAlertTrap30The tape drive has a hardware fault:
1. Eject the tape or magazine.
2. Reset the drive.
3. Restart the operation. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.30 |
tapeAlertTrap31The tape drive has a hardware fault:
1. Turn the tape drive off and then on again.
2. Restart the operation.
3. If the problem persists, call the tape
drive supplier helpline.
Check the tape drive users manual for device specific
instructions on turning the device power on and off. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.31 |
tapeAlertTrap32The tape drive has a problem with the host
interface:
1. Check the cables and cable connections.
2. Restart the operation. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.32 |
tapeAlertTrap33The operation has failed:
1. Eject the tape or magazine.
2. Insert the tape or magazine again.
3. Restart the operation. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.33 |
tapeAlertTrap34The firmware download has failed because you
have tried to use the incorrect firmware for
this tape drive.
Obtain the correct firmware and try again. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.34 |
tapeAlertTrap35Environmental conditions inside the tape drive are
exceeding the humidity specifications TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.35 |
tapeAlertTrap36Environmental conditions inside the tape drive are
exceeding the temperature specifications TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.36 |
tapeAlertTrap37The voltage supply to the tape drive exceeds specifications TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.37 |
tapeAlertTrap38A hardware failure of the tape drive is predicted.
Call the tape drive supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.38 |
tapeAlertTrap39The tape drive may have a hardware fault.
Run extended diagnostics to verify and diagnose the problem.
Check the tape drive users manual for device specific
instructions on running extended diagnostic tests. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.39 |
tapeAlertTrap40The changer mechanism is having difficulty
communicating with the tape drive:
1. Turn the autoloader off then on.
2. Restart the operation.
3. If problem persists, call the tape drive
supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.40 |
tapeAlertTrap41A tape has been left in the autoloader by a
previous hardware fault:
1. Insert an empty magazine to clear the fault.
2. If the fault does not clear, turn the autoloader
off and then on again.
3. If the problem persists, call the tape drive
supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.41 |
tapeAlertTrap42There is a problem with the autoloader mechanism. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.42 |
tapeAlertTrap43The operation has failed because the autoloader
door is open:
1. Clear any obstructions from the autoloader door.
2. Eject the magazine and then insert it again.
3. If the fault does not clear, turn the autoloader
off and then on again.
4. If the problem persists, call the tape drive
supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.43 |
tapeAlertTrap44The autoloader has a hardware fault:
1. Turn the autoloader off and then on again.
2. Restart the operation.
3. If the problem persists, call the tape drive supplier helpline.
Check the autoloader users manual for device specific
instructions on turning the device power on and off. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.44 |
tapeAlertTrap45The autoloader cannot operate without the magazine.
1. Insert the magazine into the autoloader
2. Restart the operation. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.45 |
tapeAlertTrap46A hardware failure of the changer mechanism is predicted.
Call the tape drive supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.46 |
tapeAlertTrap256The library mechanism is having difficulty communicating with the drive:
1. Turn the library off then on.
2. Restart the operation.
3. If problem persists, call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.256 |
tapeAlertTrap257There is a problem with the library mechanism.
If problem persists, call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.257 |
tapeAlertTrap258The library has a hardware fault:
1. Reset the library
2. Restart the operation.
Check the library users manual for device specific
instructions on resetting the device. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.258 |
tapeAlertTrap259The library has a hardware fault:
1. Turn the library off and then on again.
2. Restart the operation.
3. If the problem persists, call the library supplier helpline.
Check the library users manual for device specific
instructions on turning the device power on and off. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.259 |
tapeAlertTrap260The library mechanism may have a hardware fault.
Run extended diagnostics to verify and diagnose the problem.
Check the library users manual for device specific
instructions on running extended diagnostic tests. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.260 |
tapeAlertTrap261The library has a problem with the host interface:
1. Check the cables and cable connections.
2. Restart the operation. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.261 |
tapeAlertTrap262A hardware failure of the library is predicted.
Call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.262 |
tapeAlertTrap263Preventative maintenance of the library is required.
Check the library users manual for device specific
preventative maintenance tasks, or call your library
supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.263 |
tapeAlertTrap264General environmental conditions inside the library have
exceeded the humidity specifications. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.264 |
tapeAlertTrap265General environmental conditions inside the library have
exceeded the temperature specifications.e TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.265 |
tapeAlertTrap266he voltage supply to the library exceeds specifications.
There is a potential problem with the power supply or failure
of a redundant power supply TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.266 |
tapeAlertTrap267A cartridge has been left in a drive inside the library by a
previous hardware fault:
1. Insert an empty magazine to clear the fault.
2. If the fault does not clear, turn the library off and then on again.
3. If the problem persists, call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.267 |
tapeAlertTrap268There is a potential problem with a drive ejecting cartridges short or
with the library mechanism picking a cartridge from a slot.
1. No action needs to be taken at this time.
2. If the problem persists, call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.268 |
tapeAlertTrap269There is a potential problem with the library mechanism
placing a cartridge into a slot
1. No action needs to be taken at this time.
2. If the problem persists, call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.269 |
tapeAlertTrap270There is a potential problem with a drive or the library
mechanism loading cartridges, or an incompatible cartridge. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.270 |
tapeAlertTrap271The operation has failed because the library door is open:
1. Clear any obstructions from the library door.
2. Close the library door.
3. If the problem persists, call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.271 |
tapeAlertTrap272There is a mechanical problem with the
library media import/export mailslot. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.272 |
tapeAlertTrap273The library cannot operate without the magazine.
1. Insert the magazine into the library
2. Restart the operation. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.273 |
tapeAlertTrap274Library security has been compromised TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.274 |
tapeAlertTrap275The security mode of the library has been changed.
The library has either been put into secure mode,
or the library has exited the secure mode.
This is for information purposes only. No action is required. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.275 |
tapeAlertTrap276The library has been manually turned offline and is unavailable for use. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.276 |
tapeAlertTrap277A drive inside the library has been taken offline.
This is for information purposes only. No action is required. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.277 |
tapeAlertTrap278There is a potential problem with the barcode label or
the scanner hardware in the library mechanism.
1. No action needs to be taken at this time.
2. If the problem persists, call the library supplier helpline. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.278 |
tapeAlertTrap279The library has detected a inconsistency in its inventory.
1. Redo the library inventory to correct inconsistency.
2. Restart the operation
Check the applications users manual or the hardware users
manual for specific instructions on redoing the library inventory. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.279 |
tapeAlertTrap280A library operation has been attempted that is invalid at this time. TRAP-TYPE .1.3.6.1.4.1.11.2.3.9.7.1.0.280 |
control OBJECT IDENTIFIER .1.3.6.1.4.1.11.2.3.9.7.1.1 |
revMajorThe TapeAlert major revision level (left of the decimal).
Used for presence checking.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.1.1 |
revMinorThe TapeAlert minor revision level (right of the decimal).ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.1.2 |
trapEnableIndicates whether agent should or should not send TapeAlert traps.rw INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.1.3 |
autoCleanEnableIndicates whether application should or should not perform
an automatic cleaning operation based on TapeAlert cleaning
information.rw INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.1.4 |
autoCopyEnableIndicates whether application should or should not perform
an automatic tape copy or tape discard operation based on
TapeAlert media information.rw INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.1.5 |
numDevicesTotal number of tape devices attached to server and
managed by TapeAlert agent. Zero means no devices present.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.2 |
devTableA list of tape device information entries. The number
of entries is given by the value of numDevices. SEQUENCE OF DevInfo .1.3.6.1.4.1.11.2.3.9.7.1.3 |
devInfoA tape device information entry, containing configuration
information for a particular tape device. DevInfo .1.3.6.1.4.1.11.2.3.9.7.1.3.1 |
devNumA unique index value for each tape device. Its value ranges
between 1 and the value of numDevices.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.3.1.1 |
tapeAlertCapabilityIndicates whether tape device supports TapeAlert, with
zero indicating not supported and one indicating supportedro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.3.1.2 |
hbaNameName of SCSI Host Bus Adaptor connected to tape drive,
for example Adaptec AHA2740AT.ro DisplayString .1.3.6.1.4.1.11.2.3.9.7.1.3.1.3 |
hbaNumberThe number of SCSI Host Bus Adaptor connected
to tape drive, for example 0 is first HBA on the system.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.3.1.4 |
hbaChannelSCSI Channel number of SCSI Host Bus Adaptor connected
to tape drive, for example 0 is first SCSI channel of HBA.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.3.1.5 |
driveScsiIDSCSI ID of Tape Device.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.3.1.6 |
driveInquirySCSI Inquiry data of Tape Device, with vendor ID data
followed by device ID data.ro DisplayString .1.3.6.1.4.1.11.2.3.9.7.1.3.1.7 |
driveFirmwareFirmware revision of Tape Device.ro DisplayString .1.3.6.1.4.1.11.2.3.9.7.1.3.1.8 |
driveTypeDevice type of Tape Device, for example DDS1ro DisplayString .1.3.6.1.4.1.11.2.3.9.7.1.3.1.9 |
driveCompressIndicates whether Tape Device supports hardware compression,
with zero indicating not supported and one indicating supported.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.3.1.10 |
currentMediaSoftware label of current media loaded in drivero DisplayString .1.3.6.1.4.1.11.2.3.9.7.1.3.1.11 |
driveSerialNumHardware Serial Number of Tape Device, if availablero DisplayString .1.3.6.1.4.1.11.2.3.9.7.1.3.1.12 |
numErrorsTotal number of TapeAlert error traps logged by TapeAlert
agent since agent was initialised. Zero means that no
TapeAlert trap events occurred since initialisation.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.4 |
errorHistoryTableA list of historical error entries for all tape
devices on the server. The list should contain
an entry for each TapeAlert trap sent since the
TapeAlert agent was initialised. SEQUENCE OF ErrorHistoryEntry .1.3.6.1.4.1.11.2.3.9.7.1.5 |
errorHistoryEntryAn error entry in the errorHistoryTable, containing
information on a historic TapeAlert trap sent by the
TapeAlert agent ErrorHistoryEntry .1.3.6.1.4.1.11.2.3.9.7.1.5.1 |
errorIndexA unique index value for each error entry. Its value ranges
between 1 and the value of numErrors.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.5.1.1 |
errorHbaNumberThe number of SCSI Host Bus Adaptor connected to
the tape drive that caused this specific TapeAlert
error, for example 0 is first HBA on the system.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.5.1.2 |
errorHbaChannelSCSI channel number of SCSI Host Bus Adaptor connected
to the tape drive that caused this specific TapeAlert
error, for example 0 is first SCSI channel of HBA.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.5.1.3 |
errorDriveScsiIDSCSI of the tape drive that caused this specific TapeAlert
error, for example 0 is first SCSI channel of HBA.ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.5.1.4 |
errorDateDate and time of the error in yyyymmddHHMMSS format:
where
yyyy year 1980-9999
mm month 01-12
dd day 01-31
HH hour 00-23
MM minute 00-59
SS second 00-60 (use 60 for leap-second)
Example 14:35:26 5th Oct 1996 = 19961005143526ro OCTET STRING .1.3.6.1.4.1.11.2.3.9.7.1.5.1.5 |
errorTrapNumTapeAlert trap number of the error.
For tape drive/autoloader traps, range 1-64.
For library device traps, range 256-319
(Library device traps = TapeAlert flag + 255)ro INTEGER .1.3.6.1.4.1.11.2.3.9.7.1.5.1.6 |
errorMediaSoftware label of the media that was loaded in the
tape drive at the time of the error.ro DisplayString .1.3.6.1.4.1.11.2.3.9.7.1.5.1.7 |